rollup double sided 01 -...
Transcript of rollup double sided 01 -...
banner stands
rollup double sided 01RU-D1-S-3 The Rollup Double Sided 01 is a premium double-sided retractable banner stand that comes with a hybrid bungee/ telescoping pole, graphic tensioner and offers all the latest features for trade show banner displays.
dimensions:Hardware Graphic
additional information:Graphic materials:anti-curl vinyl, premium opaque fabric, melinex
Stand-off rectangle counter top is available in black thermoform only.
Stand-off literature rack is available (L112-2 only)
LV4 banner lighting option available
- Variable graphic height = 60” - 83.25”- Hybrid bungee/ telescoping pole with toolless
quick rail - Accessory channel featured on the top of the
unit (to add a literature pocket or arm table accessory)
- Adjustable feet on base
features and benefi ts:- Supplied with carry bag with strap- Anodized silver base- Single or double-sided- Quick slide graphic to leader attachment- Lifetime limitedwarranty against
manufacturer defects
Assembled unit: 33.75”(w) x 88.25”(h) max x 10.83”(d) approx.857mm(w) x 2178mm(h) x 275mm(d) approx.
Base dimensions:33.75”(w) x 3.5”(h) x 10.83”(d) approx.857mm(w) x 89mm(h) x 275mm(d) approx.
Shipping
Shipping dimensions - ships in one box42”(l) x 12”(h) x 5”(d)1067mm(l) x 305mm(h) x 127mm(d)
Approximate shipping weight (without graphics):16 lbs / 7.26 kg
Refer to related graphic template for more information.
WARNING: Always attach graphic to base and top rail before removing the locking pin. After fi tting, the graphic should be left for 24 hours before use to ensure the adhesive bonds suffi ciently. Opening the base will invalidate the product warranty.
Graphic tension may be re-applied or added by removing the end cap, then turn the ratchet tensioner clockwise.
02.01.16 © Nimlok Display and Exhibit Solutions Worldwide. For questions contact your local Nimlok distributor
Banner Stand Accessories:easy connection with cam lock and
channel
Carry bag included
Hybrid pole
Set-up
Secure pole(s) in the base of stand then add doublerTwist telescopic pole to extend 1 2 3 4
Gently lean the unit back and pull the graphic up by the toprail
Graphic to top rail attachment (metal insert)
Peel fi lm to expose adhesive; place metal insert from graphic rail on top back side of the graphic point
Loosen each screw from the rail using provided allen key and remove metal insert (do not remove screws) 1 2 3 4
Press down on the metal insert to make sure adhesive is secure on graphic
5
Insert the metal insert with graphic attached into the top graphic profi le rail
1
Quick slide top rail attachment (plastic insert)
2
Tighten the screws back in place to hold metal insert and graphic with an allen key
Leveling feet located under unit
metal insert
metal insert
metal insert
3Remove top slider from graphic railRemove fi lm to expose adhesive on top slider
Align and apply to top slider on the top front of graphic
top slider
printed side down
doubler
Align and apply to back of graphic
printed side up
4 32Insert graphic onto graphic railPeel film to expose adhesive tape on quick slider
Insert slider with graphic applied into quick slider, then center
Remove pin while holding onto the graphic so the graphic does not retract in quickly
Slide the quick slider off the leader
Slowly retract the graphic back into the base
Quick slide base attachment
quick slider
1
4 5 6
top rail slider bottom slider
graphic back
graphic frontgraphic back
graphic front
check out these related products:
We continue to improve and modify our product range and reserve the right to vary the specifi cations without prior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE. See Graphic Templates for graphic bleed specifi cations.
rollup 01
rollup 06 smart banner 01 smart banner 02
rollup 04 rollup 05rollup 02 rollup 03
rollup DS 01 rollup DS 02
rollup 03