ROBOTICS Productspecification IRB6700 ·...
Transcript of ROBOTICS Productspecification IRB6700 ·...
ROBOTICS
Product specificationIRB 6700
Trace back information:Workspace R18-1 version a16Checked in 2018-04-18Skribenta version 5.2.025
Product specificationIRB 6700-235/2.65IRB 6700-205/2.80IRB 6700-175/3.05IRB 6700-150/3.20IRB 6700-200/2.60IRB 6700-155/2.85IRB 6700-300/2.70IRB 6700-245/3.00
IRB 6700Inv-300/2.60IRB 6700Inv-245/2.90
IRC5
Document ID: 3HAC044265-001Revision: K
© Copyright 2018 ABB. All rights reserved.
The information in this manual is subject to change without notice and should notbe construed as a commitment by ABB. ABB assumes no responsibility for any errorsthat may appear in this manual.Except as may be expressly stated anywhere in this manual, nothing herein shall beconstrued as any kind of guarantee or warranty by ABB for losses, damages topersons or property, fitness for a specific purpose or the like.In no event shall ABB be liable for incidental or consequential damages arising fromuse of this manual and products described herein.This manual and parts thereof must not be reproduced or copied without ABB'swritten permission.Keep for future reference.Additional copies of this manual may be obtained from ABB.
Original instructions.
© Copyright 2018 ABB. All rights reserved.ABB AB, Robotics
Robotics and MotionSe-721 68 Västerås
Sweden
Table of contents7Overview of this product specification .............................................................................................
91 Description91.1 Structure .........................................................................................................91.1.1 Introduction ............................................................................................121.1.2 Different robot versions ............................................................................131.1.3 Definition of version designations ...............................................................181.2 Standards ........................................................................................................181.2.1 Applicable standards ...............................................................................201.3 Installation .......................................................................................................201.3.1 Introduction to installation .........................................................................211.3.2 Operating requirements ............................................................................221.3.3 Assembling the manipulator ......................................................................291.4 Calibration and references ..................................................................................291.4.1 Fine calibration .......................................................................................301.4.2 Absolute Accuracy calibration ...................................................................321.5 Load diagrams ..................................................................................................321.5.1 Introduction ............................................................................................331.5.2 Diagrams ...............................................................................................
631.5.3 Maximum load and moment of inertia for full and limited axis 5 (center line down)
movement ..............................................................................................651.5.4 Wrist torque ...........................................................................................661.5.5 Maximum TCP acceleration .......................................................................671.6 Fitting equipment to the robot .............................................................................761.7 Maintenance and troubleshooting .........................................................................771.8 Robot motion ....................................................................................................771.8.1 Robot motion ..........................................................................................901.8.2 Performance according to ISO 9283 ............................................................921.8.3 Velocity .................................................................................................931.8.4 Robot stopping distances and times ...........................................................941.9 Cooling fan for axis 1 motor ................................................................................951.10 Servo gun ........................................................................................................951.10.1 Introduction ............................................................................................961.10.2 Stationary gun ........................................................................................971.10.3 Robot gun ..............................................................................................981.10.4 Robot gun and track motion ......................................................................991.10.5 Track motion ..........................................................................................
1012 DressPack and SpotPack1012.1 Introduction ......................................................................................................1012.1.1 Included options .....................................................................................1032.1.2 Product range .........................................................................................1042.1.3 Limitations of robot movements .................................................................1052.1.4 Impact on DressPack lifetime ....................................................................1062.1.5 Information structure ...............................................................................1072.2 DressPack .......................................................................................................1072.2.1 Introduction ............................................................................................1082.2.2 Built-in features for upper arm DressPack ....................................................1092.2.3 Interface descriptions for DressPack ...........................................................1142.2.4 Dimensions ............................................................................................1152.3 Type H/HSe ......................................................................................................1152.3.1 Introduction ............................................................................................1172.3.2 Configuration result for Type H HSe ............................................................1232.3.3 Interface description for stationary gun .......................................................1262.3.4 Summary common options Type H HSe ......................................................1272.3.5 Summary options required for Type HSe .....................................................
Product specification - IRB 6700 53HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
Table of contents
1282.4 Type Se ...........................................................................................................1282.4.1 Introduction ............................................................................................1302.4.2 Configuration result for Type Se .................................................................1422.4.3 Summary common options for Type Se .......................................................1432.5 Spot Welding cabinet .........................................................................................1432.5.1 Introduction to Spot Welding cabinet ..........................................................1502.5.2 Interface description for spot welding cabinet ...............................................1512.6 Water and air unit ..............................................................................................1512.6.1 Introduction ............................................................................................1582.6.2 Technical data ........................................................................................1592.7 Connection kits .................................................................................................1602.7.1 Base - Connector kits ...............................................................................1622.7.2 Axis 3 - Connector kits .............................................................................1632.7.3 Axis 6 - Connector kits .............................................................................
1653 Specification of variants and options1653.1 Introduction to variants and options ......................................................................1663.2 Manipulator ......................................................................................................1683.3 Equipment .......................................................................................................1723.4 Floor cables .....................................................................................................1733.5 Process DressPack ...........................................................................................1743.6 DressPack floor cables .......................................................................................1753.7 DressPack Lower and Upper arm .........................................................................1763.8 Connection kits .................................................................................................1773.9 Servo Gun .......................................................................................................1783.10 SpotPack Floor Cables .......................................................................................1793.11 Process cabinet ................................................................................................1803.12 Water and air ....................................................................................................1813.13 User documentation ..........................................................................................
1834 Accessories1834.1 Introduction to accessories .................................................................................
185Index
6 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
Table of contents
Overview of this product specificationAbout this product specification
It describes the performance of themanipulator or a complete family of manipulatorsin terms of:
• The structure and dimensions prints• The fulfillment of standards, safety and operating requirements• The load diagrams, mounting or extra equipment, the motion and the robot
reach• The specification of variants and options available
UsageProduct specifications are used to find data and performance about the product,for example to decide which product to buy. How to handle the product is describedin the product manual.
UsersIt is intended for:
• Product managers and product personnel• Sales and marketing personnel• Order and customer service personnel• Robot programmers• Project leaders• Design engineers
References
Document IDReference
3HAC047400-001Product specification - Controller IRC5IRC5 with main computer DSQC1000.
3HAC048264-001Product specification - Controller software IRC5IRC5 with main computer DSQC1000 and RobotWare 5.6x.
3HAC050945-001Product specification - Controller software IRC5IRC5 with main computer DSQC1000 and RobotWare 6.
3HAC044266-001Product manual - IRB 6700
3HAC058254-001Product manual - IRB 6700Inv
3HAC052355-001Product specification - Robot user documentation, IRC5 with RobotWare6
Revisions
DescriptionRevision
First release-
Continues on next pageProduct specification - IRB 6700 73HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
Overview of this product specification
DescriptionRevision• The variants IRB 6700-200/2.60 and IRB 6700-155/2.85 are added.• Minor corrections/updates•
A
• DressPack & SpotPack updatedB• Text for Foundry Plus updated.• Two variants added, IRB 6700-300/2.70 and IRB 6700-245/3.00.• Minor corrections/update
C
• AbsAcc data added• New loads for IRB 6700-300 and -245 added• Values for power consumption, brakes engaged/disengaged added• Tightening torque for robot adjusted• The use of guide pins for robot base added• Updated data (ISO, weight) for IRB 6700-200 and IRB 6700-155
D
• Minor corrections/update• Updated standard tool flange drawing• Guide pins for base plate changed to two cylindrical
E
• Information regarding warranty for upper arm dress pack added.• Minor corrections/update• Section SpotWelding cabinet updated.
F
• Warranty information for DressPack updated.• Dimensions (measure D), for products -150/3.20 and -205/2.80 in
table Holes for fitting extra equipment are changed from 400 mmto 500 mm.
• Illustration in section Fastening holes robot base is updated regard-ing guide holes.
• Illustration regarding centering diameters on tool flange updated.
G
Published in release R17.1. The following updates are done in this revi-sion:
• Illustration for Tool flange, standard is updated.• Major structural change is made on chapter Specifications of
variants and options.• IRB 6700Inv is added.• Restriction of load diagram added.• Working range axis 2 and 3 added.
H
Published in release R17.2. The following updates are done in this revi-sion:
• Updated list of applicable standards.• Delete option 828-1, 828-2, 768-3 and 782-1 as they were all phased
out.• 635-1,3,4,5 option phased out and replaced by 636-6.• Type HS and S are phased out.• 782-7, 796-1 phased out.
J
Published in release R18.1. The following updates are done in this revi-sion:
• Water and air unit updated.
K
8 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
Overview of this product specificationContinued
1 Description1.1 Structure
1.1.1 Introduction
GeneralThe IRB 6700 series is ABB Robotics 7:th generation of high payload, highperformance industrial robots. Based on the famous IRB 6640 series, with largeworking range, the very high wrist torque, the service friendly modular built up andthe availability, significant for ABB’s robots, the IRB 6700 robot family goes evenfurther. With focus on high production capacity, compact design and low weight,simple service and low maintenance cost. The IRB 6700 is ideal for processapplications, regardless of industry. Typical areas are for example Spot Welding,Material Handling and Machine Tending.
Software product rangeWe have added a range of software products - all falling under the umbrelladesignation of Active Safety - to protect not only personnel in the unlikely eventof an accident, but also robot tools, peripheral equipment and the robot itself.
Process optionsThere are a large number of process options for SpotWelding andMaterial Handlingintegrated in the robot. For a complete description of process options for SpotWelding see DressPack and SpotPack on page 101.
Operating systemThe robot is equipped with the IRC5 controller and robot control software,RobotWare. RobotWare supports every aspect of the robot system, such asmotioncontrol, development and execution of application programs, communication etc.See Product specification - Controller IRC5 with FlexPendant.
SafetySafety standards valid for complete robot, manipulator and controller.
Additional functionalityFor additional functionality, the robot can be equipped with optional software forapplication support - for example gluing and welding, communication features -network communication - and advanced functions such as multitasking, sensorcontrol etc. For a complete description on optional software, see the Productspecification - Controller software IRC5.
Protection type Foundry Plus 2Robots with the option Foundry Plus 2 are designed for harsh environments wherethe robot is exposed to sprays of coolants, lubricants and metal spits that aretypical for die casting applications or other similar applications.
Continues on next pageProduct specification - IRB 6700 93HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.1.1 Introduction
Typical applications are spraying insertion and part extraction of die-castingmachines, handling in sand casting and gravity casting, etc. (Please refer to FoundryPrime robots for washing applications or other similar applications). Special caremust be taken in regard to operational and maintenance requirements forapplications in foundry are as well as in other applications areas. Please contactABBRobotics Sales organization if in doubt regarding specific application feasibilityfor the Foundry Plus 2 protected robot.The robot is painted with two-component epoxy on top of a primer for corrosionprotection. To further improve the corrosion protection additional rust preventiveare applied to exposed and crucial areas, e.g. has the tool flange a specialpreventive coating. Although, continuous splashing of water or other similar rustformation fluids may cause rust attach on the robots unpainted areas, joints, orother unprotected surfaces. Under these circumstances it is recommended to addrust inhibitor to the fluid or take other measures to prevent potential rust formationon the mentioned.The entire robot is IP67 compliant according to IEC 60529 - from base to wrist,which means that the electrical compartments are sealed against water and solidcontaminants. Among other things all sensitive parts are better protected than thestandard offer.Selected Foundry Plus 2 features:
• Improved sealing to prevent penetration into cavities to secure IP67• Additional protection of cabling and electronics• Special covers that protect cavities• Well-proven connectors• Nickel coated tool flange• Rust preventives on screws, washers and unpainted/machined surfaces• Extended service and maintenance program
The Foundry Plus 2 robot can be cleaned with appropriate washing equipmentaccording to the robot product manual. Appropriate cleaning and maintenance isrequired to maintain the protection, for example can rust preventive be washed offwith wrong cleaning method.
Available robot versionsThe option Foundry Plus 2 might not be available for all robot versions.See Specification of variants and options on page165 for robot versions and otheroptions not selectable together with Foundry Plus 2.
Continues on next page10 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.1.1 IntroductionContinued
Robot axes
(A)
(B)
(C)
(D)(E)
(F)
xx1300000244
DescriptionPosDescriptionPos
Axis 2BAxis 1A
Axis 4DAxis 3C
Axis 6FAxis 5E
Product specification - IRB 6700 113HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.1.1 Introduction
Continued
1.1.2 Different robot versions
GeneralThe IRB 6700 is available in ten versions.
Robot typesThe following standard robot versions are available.
Reach (m)Handling capacity for LeanID (kg)Handling capacity (kg)Robot type
2.65 m220 kg235 kgIRB 6700
2.80 m200 kg205 kgIRB 6700
2.60 m175 kg200 kgIRB 6700
3.05 m155 kg175 kgIRB 6700
2.85 m140 kg155 kgIRB 6700
3.20 m145 kg150 kgIRB 6700
2.70 m270 kg300 kgIRB 6700
3.00 m220 kg245 kgIRB 6700
2.60 m270 kg300 kgIRB 6700Inv
2.90 m210 kg245 kgIRB 6700Inv
Note
If option 780-4, LeanID is selected, the payload will decrease as stated above,for detailed information see Load diagrams on page 32
12 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.1.2 Different robot versions
1.1.3 Definition of version designations
IRB 6700 mountingHandling capacity (kg)/Reach (m)
DescriptionPrefix
IRB 6700: Floor-mounted manipulator-MountingIRB 6700Inv: Inverted-mounted manipulator
Indicates the maximum handling capacity (kg)yyyHandling capacity (kg)
Indicates the maximum reach at wrist center (m)x.xReach (m)
Manipulator weight
WeightRobot type
1250 kg iIRB 6700-235/2.65
1260 kg iIRB 6700-205/2.80
1205 kg iIRB 6700-200/2.60
1270 kg iIRB 6700-175/3.05
1220 kg iIRB 6700-155/2.85
1280 kg iIRB 6700-150/3.20
1525 kg iIRB 6700-300/2.70
1540 kg iIRB 6700-245/3.00
1690 kg iIRB 6700Inv-300/2.60
1705 kg iIRB 6700Inv-245/2.90i Weight without DressPack
Other technical data
NoteDescriptionData
< 71 dB (A) Leq (acc. to ma-chinery directive 2006/42/EG)
The sound pressure level out-side the working space.
Airborne noise level
Power consumption at max load
Inv245/2.90
Inv300/2.60
245/3.00300/2.70150/3.20155/2.85175/3.05200/2.60205/2.80235/2.65Type of move-ment
3.33.43.23.42.72.72.82.62.62.7ISO CubeMax. velocity(kW)
Inv245/2.90
Inv300/2.60
245/3.00300/2.70150/3.20155/2.85175/3.05200/2.60205/2.80235/2.65Robot in calibra-tion position
0.170.170.150.150.160.150.160.150.170.16Brakes engaged(kW)
0.991.060.750.790.770.690.820.620.840.71Brakes disen-gaged (kW)
Continues on next pageProduct specification - IRB 6700 133HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.1.3 Definition of version designations
E1
E4 E3
E2
A
xx1000000101
DescriptionPos
1,000 mmA
Continues on next page14 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.1.3 Definition of version designationsContinued
Main dimensions of IRB 6700
78
0
20
0
1009
377
J
D
H
A
E
C
G
F
745
10
09
36
0 3
60
B
xx1300000241
DescriptionPos
200 mm (all standard variants); except 300/2.70 and 245/3.00 =220 mm350 mm (all LeanID variants, option 780-4); except IRB 300/2.70 and 245/3.00 =380 mm
A
Radius ax1, front = 532 mm (IRB 6700-235/2.65, -205/2.80, -175/3.05, -150/3.20,-200/2.60 and -155/2.85)
B
Radius ax1, front = 600 mm (IRB 6700-300/2.70 and -245/3.00)
Radius ax1, back = 633 mm (IRB 6700-235/2.65, -205/2.80, -175/3.05, -150/3.20,-200/2.60 and -155/2.85)
C
Radius ax1, back = 700 mm (IRB 6700-300/2.70 and -245/3.00)
JHGFEDRobot variant
1862091,182.5167011352300IRB 6700 - 235/2.65
2091861,182.5167012802445IRB 6700 - 205/2.80
193197.51,142.5162311252276IRB 6700 - 200/2.60
1862091,592.5208011352300IRB 6700 - 175/3.05
1862091,592.5208012802445IRB 6700 - 150/3.20
193197.51,392.5187311252276IRB 6700 - 155/2.85
Continues on next pageProduct specification - IRB 6700 153HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.1.3 Definition of version designations
Continued
JHGFEDRobot variant
187222.51212.51718.511452321IRB 6700 - 300/2.70
186222.51462.51968.511452321IRB 6700 - 245/3.00
Note
For DressPack dimensions, seeDimensions for robot with DressPack on page114
Continues on next page16 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.1.3 Definition of version designationsContinued
Main dimensions of IRB 6700Inv
1009
377
D
830
200
E
AG
F
H
360
360
1009
B
C
J
xx1700000559
DescriptionPos
220 mm (all IRB 6700Inv variants)A380 mm (all IRB 6700Inv LeanID variants, option 780-4)
Radius ax1, front = 626 mmB
Radius ax1, back = 910 mmC
JHGFEDRobot variant
187222.51212.51718.511452372IRB 6700Inv - 300/2.60
186222.51468.51968.511452372IRB 6700Inv - 245/2.90
Product specification - IRB 6700 173HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.1.3 Definition of version designations
Continued
1.2 Standards
1.2.1 Applicable standards
Note
The listed standards are valid at the time of the release of this document. Phasedout or replaced standards are removed from the list when needed.
Standards, EN ISOThe product is designed in accordance with the requirements of:
DescriptionStandard
Safety of machinery - General principles for design - Risk as-sessment and risk reduction
EN ISO 12100:2010
Safety of machinery, safety related parts of control systems -Part 1: General principles for design
EN ISO 13849-1:2015
Safety of machinery - Emergency stop - Principles for designEN ISO 13850:2015
Robots for industrial environments - Safety requirements -Part1 Robot
EN ISO 10218-1:2011
Robots and robotic devices -- Coordinate systems and motionnomenclatures
ISO 9787:2013
Manipulating industrial robots, performance criteria, and relatedtest methods
ISO 9283:1998
Classification of air cleanlinessEN ISO 14644-1:2015 i
Ergonomics of the thermal environment - Part 1EN ISO 13732-1:2008
EMC, Generic emissionEN 61000-6-4:2007 +A1:2011IEC 61000-6-4:2006 +A1:2010(option 129-1)
EMC, Generic immunityEN 61000-6-2:2005IEC 61000-6-2:2005
Arc welding equipment - Part 1: Welding power sourcesEN IEC 60974-1:2012 ii
Arc welding equipment - Part 10: EMC requirementsEN IEC 60974-10:2014 ii
Safety of machinery - Electrical equipment of machines - Part1 General requirements
EN IEC 60204-1:2006
Degrees of protection provided by enclosures (IP code)IEC 60529:1989 + A2:2013i Only robots with protection Clean Room.ii Only valid for arc welding robots. Replaces EN IEC 61000-6-4 for arc welding robots.
European standards
DescriptionStandard
Safety of machinery - Ergonomic design principles - Part 1:Terminology and general principles
EN 614-1:2006 + A1:2009
Continues on next page18 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.2.1 Applicable standards
DescriptionStandard
Safety of machinery - Two-hand control devices - Functionalaspects - Principles for design
EN 574:1996 + A1:2008
Other standards
DescriptionStandard
Safety requirements for industrial robots and robot systemsANSI/RIA R15.06
Safety standard for robots and robotic equipmentANSI/UL 1740
Industrial robots and robot Systems - General safety require-ments
CAN/CSA Z 434-14
Product specification - IRB 6700 193HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.2.1 Applicable standards
Continued
1.3 Installation
1.3.1 Introduction to installation
GeneralIRB 6700 are designed for floor mounting (no tilting allowed around X-axis orY-axis). IRB 6700Inv are designed for inverted mounting (no tilting allowed aroundX-axis or Y-axis).Depending on the robot version, an end effector with max. weightof 150 to 300 kg including payload, can be mounted on the tool flange (axis 6). SeeLoad diagrams on page 32.
Extra loadsExtra load (valve packages, transformers, DressPack) of 50 kg, which is includedin the load diagrams, can be mounted on the upper arm. An extra load of 250 kgcan also be mounted on the frame of axis 1.See Fitting equipment to the robot on page 67.
Working range limitationThe working range of axes 1 can be limited by mechanical stops as option. SeeWorking range limitation on page 170.
20 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.3.1 Introduction to installation
1.3.2 Operating requirements
Protection standards
IEC 60529Robot version/Protection standard
IP67All variants, manipulator
Explosive environmentsThe robot must not be located or operated in an explosive environment.
Ambient temperature
TemperatureStandard/OptionDescription
Minimum: +5°C i (41°F)StandardManipulator during operationMaximum: +50°C (122°F)
SeeProduct specification - Control-ler IRC5
Standard/OptionFor the controller
+ 5°C (41°F) to + 45°C (113°F)StandardFor the spot welding cabinet
Minimum: -25°C (-13°F)StandardComplete robot during transporta-tion and storage, Maximum: +55°C (+131°F)
+70°C (+158°F)Standardfor short periods (not exceeding24 hours)i At low environmental temperature (below 10° C) a warm-up phase is recommended to be run with
the robot. Otherwise there is a risk that the robot stops or runs with lower performance due totemperature dependent oil and grease viscosity.
Relative humidity
Relative humidityDescription
Maximum 95% at constant temper-ature.
Complete robot during transportation and storage
Maximum 95% at constant temper-ature.
Complete robot during operation
Product specification - IRB 6700 213HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.3.2 Operating requirements
1.3.3 Assembling the manipulator
Maximum loadMaximum load in relation to the base coordinate system.
Floor mounted
Max. load (emergency stop)Endurance load (in operation)Force
±19.8 kN i / ±21.8 kN ii±7.4 kN i / ±8.7 kN iiForce xy
14.6 ±15.7 kN i / 18.0 ±17.4 kN ii14.6 ±4.5 kN i / 18.0 ±5.4 kN iiForce z
±37.1 kNm i / ±45.3 kNm ii±21.0 kNm i / ±24.9 kNm iiTorque xy
±11.4 kNm i / ±15.5 kNm ii±5.0 kNm i / ±6.5 kNm iiTorque zi Valid for IRB 6700-235, -205, -175, -150, -200, -155.ii Valid for IRB 6700-300, -245.
Inverted Mounted
Max. load (emergency stop)Endurance load (in operation)Force
±23.7 kN i±8.9 kN iForce xy
-22.1 ± 18.1 kN i-22.1 ±6.6 kN iForce z
±45.4 kNm i±22.5 kNm iTorque xy
±15.7 kNm i±6.5 kNm iTorque zi Valid for IRB 6700Inv-300, -245.
xx1300000242
Continues on next page22 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.3.3 Assembling the manipulator
Note regarding Mxy and FxyThe bending torque (Mxy) can occur in any direction in the XY-plane of the basecoordinate system.The same applies to the transverse force (Fxy).
Fastening holes robot base - for all variants
D - D
8x 30
8x 53
4x 45 H7
4x
3x45
16
8x
49,5
0,3 A
0,12
A
800
4x 90°
52,5
°
4x 15°
D
D
E
E
2x 25 H8
20
(25
H8)
2x4
5°
24,5
2x
0,12
E - E
(A)
(A)
xx1300000243
DescriptionPos
Holes for guide pins (x2)A
Note
Holes for guide pins (x2) Rear hole straight slot, see Guide pins on page 28.
Continues on next pageProduct specification - IRB 6700 233HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.3.3 Assembling the manipulator
Continued
Fastener quality
M24 x 100 (installation on baseplate/foundation)
Suitable screws:
8.8Quality:
90% (v=0.9)Screw tightening yield point utilization factor (v)(according to VDI2230):
4 mm flat washerSuitable washer:
550 Nm (screws lubricated with Molykote1000)
Tightening torque:
600-725 Nm, typical 650 Nm (screws noneor lightly lubricated)
Note
Only two guide pins shall be used. The corresponding holes in the base plateshall be circular according to figure Base plate drawing on page 25.
AbsAcc performanceRegarding AbsAcc performance, the use of guide pins are mandatory.
Continues on next page24 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.3.3 Assembling the manipulatorContinued
Base plate drawing
Note
IRB 6700Inv is not valid for base plate.
The following figure shows the option base plate (dimensions in mm).
12x M 24
3x 25
4x
15
° 4
x 2
5°
2x
7,5
°
37
,5°
4x
9
0°
80
0
540
47
5
10°
10
°
90° 9
0°
0
27
448
0
87
45
3
A
A
B
B
C C
D
E
E
Ref A-B
E-E
1 A B
HG
F E
4x
48
3x45
13
45 P7
--0,0170,042
A-A
1,6
1,5
A
2x 12H7 0
+0,018
2x 1x452x 18±
1 (H
7)
20±1
2
32 ±
1
M5
0,1 A B
D
(A)
(B)
0,2 Common Zone E, F, G, H
xx1500000246
DescriptionPos
Hole for guide pin, cylindrical, see Guide pins on page 28A, B
Common tolerance zone (accuracy all over the base plate from one contactsurface to the other)
E, F, G, H
Continues on next pageProduct specification - IRB 6700 253HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.3.3 Assembling the manipulator
Continued
3x45
13
48
2
B-B
1,6
2x R
37
,5°
47 +
0,50
23,5
45
K7
+-
0,00
70,
018
D
CL 2x R22,5
B
3x R1
3x 90°
3x 4
C-C
xx1500000247
Continues on next page26 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.3.3 Assembling the manipulatorContinued
16x R 504x 18
2x
R52
5
50
x4
5°
(2x
) 00
00
672,5680,1
813,9784,8
2x 598
2x 298
215,9223,5
111,282,1
61
9
67
7
79
47
87
,6
2x
70
3
2x
20
3
92111,4
198,8214,1
681,9697,2
804784,6
2x
22
4,1
2x
27
8,3
2x
11
9,9
2x
13
2,8
87
27
87
27
5x M16
16x 22
(1020)
( 9
50
)
0
0
0
0
2x
27
1
2x
77
4
41
123
358
175
538
721
773
855896923 ±1
93
3±
1
2x
86
0
2x
72
6
2x
54
3
2x
36
3
2x
20
6
110
448
786
878
87±
18
7
27±127
50
18
69
2x
90
4
50
+-
31
xx1500000249
Color: RAL 9005Thickness: 80-100 µmWeight: 360 kg
A
Continues on next pageProduct specification - IRB 6700 273HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.3.3 Assembling the manipulator
Continued
Guide pins 25g6
12k6
18
1
5
(A)
XX1500000248
DescriptionPos
Cylindrical guide pin (x2)A
Assembly of guide pins
800
B B
B-B
(A)
(B)
(A)
DescriptionPos
Cylindrical guide pin (x2)A
M5 x 40. Tightening torque 6 Nm. (x2)B
Note
All screws and pins are delivered in a plastic bag together with the base plate.
28 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.3.3 Assembling the manipulatorContinued
1.4 Calibration and references
1.4.1 Fine calibration
GeneralFine calibration is made using the Calibration Pendulum, see Operatingmanual - Calibration Pendulum or Axis calibration, see Product manual - IRB 6700and Product manual - IRB 6700Inv.
(A)
(B)
(C)
(D)(E)
(F)
xx1300000244
Axes
DescriptionPosDescriptionPos
Axis 2BAxis 1A
Axis 4DAxis 3C
Axis 6FAxis 5E
Calibration
PositionCalibration
All axes are in zero positionCalibration of all axes
Axis 1 and 2 in zero positionCalibration of axis 1 and 2
Axis 3 to 6 in any position
Axis 1 in zero positionCalibration of axis 1
Axis 2 to 6 in any position
Product specification - IRB 6700 293HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.4.1 Fine calibration
1.4.2 Absolute Accuracy calibration
Note
IRB 6700Inv is valid for field AbsAcc but does not have an AbsAcc option.
GeneralRequires RobotWare option Absolute Accuracy, see Productspecification - Controller software IRC5 for more details.
The calibration conceptAbsolute Accuracy (AbsAcc) is a calibration concept, which ensures a TCP absoluteaccuracy of better than ± 1 mm in the entire working range (working range ofbending backward robots, for example IRB 6700, are limited to only forwardpositions).Absolute accuracy compensates for:
• Mechanical tolerances in the robot structure• Deflection due to load
Absolute accuracy calibration is focusing on positioning accuracy in the cartesiancoordinate system for the robot. It also includes load compensation for deflectioncaused by the tool and equipment. Tool data from robot program is used for thispurpose. The positioning will be within specified performance regardless of load.
Calibration dataThe user is supplied with robot calibration data (compensation parameters savedon the manipulator SMB) and a certificate that shows the performance (Birthcertificate). The difference between an ideal robot and a real robot without AbsAccmay reach up to 8 mm, resulting from mechanical tolerances and deflection in therobot structure.If there is a difference at first start-up between the calibration data in the controllerand the robot SMB, correct it by copying the data from the SMB to the controller.
Absolute Accuracy optionAbsolute Accuracy option is integrated in the controller algorithms for compensationof this difference and does not need external equipment or calculation.Absolute Accuracy is a RobotWare option and includes an individual calibrationof the robot (mechanical arm).
Continues on next page30 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.4.2 Absolute Accuracy calibration
Absolute Accuracy is a TCP calibration in order to reach a good positioning in theCartesian coordinate system.
xx1300002177
Product dataTypical production data regarding calibration are:
Positioning accuracy (mm)Robot
% Within 1 mmMaxAverage
1000.750.35IRB 6700-235/2.55
1000.750.35IRB 6700-205/2.80
1000.750.35IRB 6700-200/2.60
1000.750.35IRB 6700-175/3.05
1000.750.35IRB 6700-155/2.85
1000.750.35IRB 6700-150/3.20
1000.750.35IRB 6700-300/2.70
1000.750.35IRB 6700-245/3.00
1000.850.40IRB 6700 LeanID (allvariants)
Product specification - IRB 6700 313HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.4.2 Absolute Accuracy calibration
Continued
1.5 Load diagrams
1.5.1 Introduction
WARNING
It is very important to always define correct actual load data and correct payloadof the robot. Incorrect definitions of load data can result in overloading of therobot.If incorrect load data and/or loads are outside load diagram is used the followingparts can be damaged due to overload:• motors• gearboxes• mechanical structure
WARNING
In the robot system the service routine LoadIdentify is available, which allowsthe user to make an automatic definition of the tool and load, to determine correctload parameters.See Operating manual - IRC5 with FlexPendant, for detailed information.
WARNING
Robots running with incorrect load data and/or with loads outside diagram, willnot be covered by robot warranty.
GeneralThe load diagrams include a nominal payload inertia, J0 of 15 kgm2 , and an extraload of 50 kg at the upper arm housing.At different moment of inertia the load diagram will be changed. For robots thatare allowed tilted, wall or inverted mounted, the load diagrams as given are validand thus it is also possible to use RobotLoad within those tilt and axis limits.
Control of load case by "RobotLoad"To easily control a specific load case, use the calculation programABBRobotLoad.Contact your local ABB organization for more information.The result from RobotLoad is only valid within the maximum loads and tilt angles.There is no warning if the maximum permitted armload is exceeded. For over loadcases and special applications, contact ABB for further analysis.
32 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.1 Introduction
1.5.2 Diagrams
IRB 6700-235/2.65
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,10 0,20 0,30 0,40 0,50
200 m
mZ
- (
m)
L - (m)
120 kg
225 kg
190 kg
140 kg
165 kg
230 kg
235 kg
240 kg
245 kg
xx1300000245
Continues on next pageProduct specification - IRB 6700 333HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
IRB 6700-235/2.65 "Vertical Wrist" (±10o)
200 m
mZ
- (
m)
L - (m)
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,10 0,20 0,30 0,40 0,50 0,60 0,70
Z
L
10o
10o
275 kg
265 kg250 kg
235 kg 210 kg
xx1300000246
For wrist down (0o deviation from the vertical line).
Description
280 kgMax load
0.327 mZmax
0.100 mLmax
Continues on next page34 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700-235/2.65 "LeanID", option 780-4
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,10 0,20 0,30 0,40 0,50 0,60
L - (m)
Z -
(m
) 3
50
mm
110 kg
130 kg
150 kg
175 kg
200 kg
220 kg
230 kg
225 kg
xx1300000248
Continues on next pageProduct specification - IRB 6700 353HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700-205/2.80
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,10 0,20 0,30 0,40 0,50
200 m
mZ
- (
m)
L - (m)
0,60
0,90
100 kg
205 kg
150 kg
125 kg
215 kg
210 kg
200 kg
195 kg
175 kg
xx1300000249
Continues on next page36 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700-205/2.80 "Vertical Wrist" (±10o)
200 m
mZ
- (
m)
L - (m) Z
L
10o
10o
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,10 0,20 0,30 0,40 0,50 0,60 0,70
235 kg
195 kg
215 kg
225 kg
205 kg
xx1300000250
For wrist down (0o deviation from the vertical line).
Description
240 kgMax load
0.355 mZmax
0.103 mLmax
Continues on next pageProduct specification - IRB 6700 373HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700-205/2.80 "LeanID", option 780-4
35
0 m
m
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
0,10 0,20 0,30 0,40 0,50 0,60
90 kg
110 kg
130 kg
150 kg
175 kg
190 kg
195 kg
200 kg
205 kg
Z -
(m
)
L - (m)
xx1300000251
Continues on next page38 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700-200/2.60
200 m
m
Z -
(m
)
L - (m)
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,10 0,20 0,30 0,40 0,50
90 kg
110 kg
155 kg
180 kg
200 kg
205 kg
210 kg
130 kg
xx1300000333
Continues on next pageProduct specification - IRB 6700 393HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700-200/2.60 "Vertical Wrist" (±10o)
200 m
m
Z -
(m
)
L - (m) Z
L
10o
10o
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
0,10 0,20 0,30 0,40 0,50 0,60 0,70 0,80 0,90
235 kg
220 kg
120 kg
160 kg
205 kg
xx1300000334
For wrist down (0o deviation from the vertical line).
Description
242 kgMax load
0.27 mZmax
0.104 mLmax
Continues on next page40 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700-200/2.60 "LeanID", option 780-4
35
0 m
m
L - (m)
Z -
(m
)
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,10 0,20 0,30 0,40 0,50
100 kg
190 kg
185 kg
175 kg
160 kg
140 kg
120 kg
xx1300000335
Continues on next pageProduct specification - IRB 6700 413HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700-175/3.05
200 m
mZ
- (
m)
L - (m)
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
0,10 0,20 0,30 0,40 0,50 0,60
150 kg
180 kg
175 kg
170 kg
165 kg
125 kg
100 kg
160 kg
xx1300000252
Continues on next page42 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700-175/3.05 "Vertical Wrist" (±10o)
200 m
mZ
- (
m)
Z
L
10o
10o
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
0,10 0,20 0,30 0,40 0,50 0,60 0,70 0,80 0,90
200 kg
190 kg
180 kg
165 kg
140 kg
L - (m)
xx1300000253
Description
204 kgMax load
0.360 mZmax
0.101 mLmax
Continues on next pageProduct specification - IRB 6700 433HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700-175/3.05 "LeanID", option 780-4
35
0 m
m L - (m)
Z -
(m
)
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
0,10 0,20 0,30 0,40 0,50 0,60 0,70
160 kg
155 kg
150 kg
100 kg
120 kg
140 kg
145 kg
85 kg
xx1300000254
Continues on next page44 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700-155/2.85
200 m
mZ
- (
m)
L - (m)
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,10 0,20 0,30 0,40 0,50
90 kg
155 kg
150 kg
145 kg
125 kg
105 kg
160 kg
xx1300000336
Continues on next pageProduct specification - IRB 6700 453HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700-155/2.85 "Vertical Wrist" (±10o)
200 m
m
Z -
(m
)
L - (m) Z
L
10o
10o
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,10 0,20 0,30 0,40 0,50 0,60 0,70 0,80
180 kg
170 kg
130 kg
150 kg
160 kg
xx1300000337
Description
186 kgMax load
0.327 mZmax
0.101 mLmax
Continues on next page46 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700-155/2.85 "LeanID", option 780-4
35
0 m
m L - (m)
Z -
(m
)
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
0,10 0,20 0,30 0,40 0,50
80 kg
100 kg
145 kg
140 kg
135 kg
130 kg
120 kg
xx1300000338
Continues on next pageProduct specification - IRB 6700 473HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700-150/3.20
200 m
mZ
- (
m)
L - (m)
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
1,00
1,10
0,10 0,20 0,30 0,40 0,50 0,60 0,70
155 kg
80 kg
100 kg
120 kg
140 kg
145 kg
150 kg
xx1300000255
Continues on next page48 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700-150/3.20 "Vertical Wrist" (±10o)
200 m
mZ
- (
m)
L - (m)Z
L
10o
10o
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
1,00
1,10
0,10 0,20 0,30 0,40 0,50 0,60 0,70 0,80 0,90 1,00 1,10
170 kg
110 kg
140 kg
150 kg
160 kg
xx1300000256
For wrist down (0o deviation from the vertical line).
Description
177 kgMax load
0.394 mZmax
0.106 mLmax
Continues on next pageProduct specification - IRB 6700 493HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700-150/3.20 "LeanID", option 780-4
35
0 m
m L - (m)
Z -
(m
)
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
1,00
1,10
0,10 0,20 0,30 0,40 0,50 0,60 0,70 0,80
70 kg
90 kg
110 kg
130 kg
145 kg
140 kg
135 kg
xx1300000257
Continues on next page50 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700-300/2.70
220 m
mZ
- (
m)
L - (m)
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
0,10 0,20 0,30 0,40 0,50 0,60
150 kg
200 kg
230 kg
270 kg
290 kg
300 kg
310 kg
175 kg
xx1400002044
Continues on next pageProduct specification - IRB 6700 513HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700-300/2.70 "Vertical Wrist" (±10o)
220 m
mZ
- (
m)
L - (m) Z
L
10o
10o
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,10 0,20 0,30 0,40 0,50 0,60 0,70 0,80
250 kg
290 kg
310 kg
350 kg330 kg
xx1400002045
For wrist down (0o deviation from the vertical line).
Description
357 kgMax load
0.308 mZmax
0.102 mLmax
Continues on next page52 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700-300/2.70 "LeanID", option 780-4
L - (m)
Z -
(m
) 3
80
mm
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,10 0,20 0,30 0,40 0,50 0,60
140 kg
250 kg
280 kg
290 kg
190 kg
165 kg
220 kg
270 kg
275 kg
285 kg
xx1400002046
Continues on next pageProduct specification - IRB 6700 533HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700-245/3.00
220 m
m
Z -
(m
)
L - (m)
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
1,00
0,10 0,20 0,30 0,40 0,50 0,60
255 kg
140 kg
225 kg
210 kg
170 kg
245 kg
250 kg
235 kg
xx1400002041
Continues on next page54 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700-245/3.00 "Vertical Wrist" (±10o)
220 m
m L - (m)Z
L
10o
10o
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
1,00
1,10
1,20
0,10 0,20 0,30 0,40 0,50 0,60 0,70 0,80 0,90 1,00 1,10 1,20
Z -
(m
)
225 kg
185 kg
150 kg
250 kg
270 kg
xx1400002042
For wrist down (0o deviation from the vertical line).
Description
315 kgMax load
0.280 mZmax
0.102 mLmax
Continues on next pageProduct specification - IRB 6700 553HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700-245/3.00 "LeanID", option 780-4
L - (m)
Z -
(m
) 3
80
mm
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0,90
0,10 0,20 0,30 0,40 0,50 0,60
225 kg
220 kg
215 kg
210 kg
205 kg
190 kg
170 kg
150 kg
130 kg
230 kg
xx1400002043
Continues on next page56 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700Inv-300/2.60
220 m
m
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0.90
1.00
0.10 0.20 0.30 0.40 0.50 0.60
Z-
(m)
L - (m)
140 kg
170 kg
200 kg
230 kg
270 kg
290 kg
300 kg
310 kg
xx1600002017
Continues on next pageProduct specification - IRB 6700 573HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700Inv-300/2.60 "Vertical Wrist" (±10o)
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80
Z-
(m)
L - (m)
Z
L
10o
10o
220 m
m
340 kg325 kg
310 kg
290 kg
250 kg
xx1600002018
For wrist down (0o deviation from the vertical line).
Description
352 kgMax load
0.332 mZmax
0.105 mLmax
Continues on next page58 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700Inv-270/2.60 "LeanID", option 780-4
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0.10 0.20 0.30 0.40 0.50 0.60
Z-
(m)
L - (m)
38
0 m
m
150 kg
170 kg
190 kg
220 kg
250 kg
270 kg
275 kg
280 kg
xx1600002050
Continues on next pageProduct specification - IRB 6700 593HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700Inv-245/2.90
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0.90
0.10 0.20 0.30 0.40 0.50 0.60
Z-
(m)
L - (m)
220 m
m150 kg
180 kg
210 kg
225 kg
235 kg
245 kg
250 kg
255 kg
xx1600002019
Continues on next page60 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
IRB 6700Inv-245/2.90 "Vertical Wrist" (±10o)
Z
L
10o
10o
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10
Z-
(m)
L - (m)
220 m
m
275 kg255 kg
235 kg
200 kg
160 kg
xx1600002020
For wrist down (0o deviation from the vertical line).
Description
284 kgMax load
0.345 mZmax
0.101 mLmax
Continues on next pageProduct specification - IRB 6700 613HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 Diagrams
Continued
IRB 6700Inv-210/2.90 "LeanID", option 780-4
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0.90
0.10 0.20 0.30 0.40 0.50 0.60 0.70
Z-
( m)
L - (m)
38
0 m
m120 kg
150 kg
180 kg
190 kg
200 kg
210 kg
215 kg
220 kg
xx1600002051
62 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.2 DiagramsContinued
1.5.3 Maximum load and moment of inertia for full and limited axis 5 (center linedown) movement
Note
Total load given as: mass in kg, center of gravity (Z and L) in meters andmomentof inertia (Jox, Joy, Joz ) in kgm2 . L= sqr (X2 + Y2), see the following figure.
Full movement of axis 5 (±130o)
Maximum moment of inertiaRobot typeAxis
Ja5 = Load x ((Z + 0,200 i )2 + L2 ) + max (J0x, J0y) ≤ 250 kgm2IRB 6700-235/2.65IRB 6700-205/2.80
5
IRB 6700-175/3.05IRB 6700-150/3.20
Ja5 = Load x ((Z + 0,200 i )2 + L2 ) + max (J0x, J0y) ≤ 195 kgm2IRB 6700-200/2.60IRB 6700-155/2.85
Ja5 = Load x ((Z + 0,220 ii )2 + L2 ) + max (J0x, J0y) ≤ 325 kgm2IRB 6700-300/2.70IRB 6700-245/3.00IRB 6700Inv-300/2.60IRB 6700Inv-245/2.90
Ja6 = Load x L2 + J0Z ≤ 185 kgm2IRB 6700-235/2.65IRB 6700-205/2.80
6
IRB 6700-175/3.05IRB 6700-150/3.20
Ja6 = Load x L2 + J0Z ≤ 145 kgm2IRB 6700-200/2.60IRB 6700-155/2.85
Ja6 = Load x L2 + J0Z ≤ 225 kgm2IRB 6700-300/2.70IRB 6700-245/3.00IRB 6700Inv-300/2.60IRB 6700Inv-245/2.90
i For option 780-4, LeanID = 0,350 mii For option 780-4, LeanID = 0,380 m
xx1400002028
DescriptionPos
Center of gravityA
Description
Max. moment of inertia around the X, Y and Z axes at center of gravity.Jox, Joy, Joz
Continues on next pageProduct specification - IRB 6700 633HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.3 Maximum load and moment of inertia for full and limited axis 5 (center line down) movement
Limited axis 5, center line down
Maximum moment of inertiaRobot typeAxis
Ja5 = Load x ((Z + 0,200 i )2 + L2 ) + max (J0x, J0y) ≤ 275 kgm2IRB 6700-235/2.65IRB 6700-205/2.80
5
IRB 6700-175/3.05IRB 6700-150/3.20
Ja5 = Load x ((Z + 0,200 i )2 + L2 ) + max (J0x, J0y) ≤ 215 kgm2IRB 6700-200/2.60IRB 6700-155/2.85
Ja5 = Load x ((Z + 0,220 ii )2 + L2 ) + max (J0x, J0y) ≤ 360 kgm2IRB 6700-300/2.70IRB 6700-245/3.00IRB 6700Inv-300/2.60IRB 6700Inv-245/2.90
Ja6 = Load x L2 + J0Z ≤ 250 kgm2IRB 6700-235/2.65IRB 6700-205/2.80
6
IRB 6700-175/3.05IRB 6700-150/3.20
Ja6 = Load x L2 + J0Z ≤ 195 kgm2IRB 6700-200/2.60IRB 6700-155/2.85
Ja6 = Load x L2 + J0Z ≤ 320 kgmIRB 6700-300/2.70IRB 6700-245/3.00IRB 6700Inv-300/2.60IRB 6700Inv-245/2.90
i For option 780-4, LeanID = 0,350 mii For option 780-4, LeanID = 0,380 m
xx1400002029
DescriptionPos
Center of gravityA
Description
Max. moment of inertia around the X, Y and Z axes at centerof gravity.
Jox, Joy, Joz
64 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.3 Maximum load and moment of inertia for full and limited axis 5 (center line down) movementContinued
1.5.4 Wrist torque
Note
The values are for reference only, and should not be used for calculating permittedload offset (position of center of gravity) within the load diagram, since thosealso are limited by main axes torques as well as dynamic loads. Also arm loadswill influence the permitted load diagram. For finding the absolute limits of theload diagram, use the ABB RobotLoad. Contact your local ABB organization.
TorqueThe table below shows the maximum permissible torque due to payload.
Max torque valid atload
Max wrist torqueaxis 6
Max wrist torqueaxis 4 and 5
Robot type
225 kg650 Nm1324 NmIRB 6700-235/2.65
192 kg625 Nm1263 NmIRB 6700-205/2.80
175 kg429 Nm981 NmIRB 6700-200/2.60
154 kg589 Nm1179 NmIRB 6700-175/3.05
144 kg410 Nm927 NmIRB 6700-155/2.85
137 kg570 Nm1135 NmIRB 6700-150/3.20
280 kg865 Nm1825 NmIRB 6700-300/2.70
214 kg815 Nm1693 NmIRB 6700-245/3.00
280 kg865 Nm1,825 NmIRB 6700Inv-300/2.60
194 kg796 Nm1,645 NmIRB6700Inv-245/2.90
Product specification - IRB 6700 653HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.4 Wrist torque
1.5.5 Maximum TCP acceleration
GeneralHigher values can be reached with lower loads than the nominal because of ourdynamical motion control QuickMove2. For specific values in the unique customercycle, or for robots not listed in the table below, we recommend then to useRobotStudio.
Maximum Cartesian design acceleration for nominal loads
Controlled MotionMax acceleration at nominal loadCOG [m/s2 ]
E-stopMax acceleration at nominalload COG [m/s2 ]
Robot type
2241IRB 6700 - 235/2.65
2445IRB 6700 - 205/2.8
2542IRB 6700 - 175/3.05
2447IRB 6700 - 150/3.2
2351IRB 6700 - 200/2.6
2947IRB 6700 - 155/2.85
2139IRB 6700 - 300/2.7
2744IRB 6700 - 245/3.0
Note
Acceleration levels for E-stop and controlled motion includes acceleration dueto gravitational forces. Nominal load is define with nominal mass and cog withmax offset in Z and L (see load diagram).
66 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.5.5 Maximum TCP acceleration
1.6 Fitting equipment to the robot
GeneralExtra loads can be fitted on the upper arm housing, the lower arm, and on theframe. Definitions of distances andmasses are shown in the following figures. Therobot is supplied with holes for fitting extra equipment (see figure in Holes for fittingextra equipment on page 70). Maximum allowed arm load depends on center ofgravity of arm load and robot payload.
Note
All equipment and cables used on the robot, must be designed and fitted not todamage the robot and/or its parts.
Frame (hip load)Extra load can be fitted on the frame.
Description
JH = 100 kgm2Permitted extra load on frame
JH = JH0 + M4 x R2Recommended position (see the fol-lowing figure) where:
• JH0 is the moment of inertia of the equipment• R is the radius (m) from the center of axis 1• M4 is the total mass (kg) of the equipment
including bracket and harness (≤ 250 kg)
Continues on next pageProduct specification - IRB 6700 673HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.6 Fitting equipment to the robot
R
xx1300000262
Upper armAllowed extra load on the upper arm housing, in addition to the maximum handlingweight, is M1 ≤ 50 kg with a distance (a) ≤ 500 mm from the center of gravity in theaxis-3 extension.
a
(A)
M1
M1
xx1400002019
Mass centerA
Continues on next page68 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.6 Fitting equipment to the robotContinued
200
400(A)
xx1300000866
Center of gravity 50 kgA
Continues on next pageProduct specification - IRB 6700 693HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.6 Fitting equipment to the robot
Continued
Holes for fitting extra equipment
Position of attachment holes - drawing 1
0,3 80
16
0
3x M10
A
A
(2x M12)
(2x M12)
CL Axis 5
2x M8 16
80
40
100
CL Axis 3
4x M12 22
220
190
110
90
32
8
192x M12
197
M12 1922)106 (4x M12
53
52,5°
117R
13
4xM
8
M12 20
52,5°
H
H
(15
0)
(150)
(109)
JK
K
A - A
J
(2x M12 19) (M12 19)
CL Axis 4
B
B
A
B
E
L
H
J
M
K
C
D
F
G
12
N
B - B
xx1300000263
Allowed position for attachment holes, M12 through. Be careful not to touch the cables when drilling.A
Continues on next page70 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.6 Fitting equipment to the robotContinued
NMLKJHGFEDCB iVariant
21010410233147349437365652.5400270R=216IRB 6700 - 235/2.65
21010410233147349437365652.5500270R=216IRB 6700 - 205/2.80
21010410233147349437365652.5400270R=216IRB 6700 - 175/3.05
21010410233147349437365652.5500270R=216IRB 6700 - 150/3.20
2109510243143315437365650.5400270R=204.5IRB 6700 - 200/2.60
2109510243143315437365650.5400270R=204.5IRB 6700 - 155/2.85
215.598.511712152405467376652.5450310R=230IRB 6700 - 300/2.70
215.598.511712152405467376652.5450310R=230IRB 6700 - 245/3.00
215.598.511712152405467425.6652.5450310R=230IRB 6700Inv - 300/2.60
215.598.511712152405467425.6652.5450310R=230IRB 6700Inv - 245/2.90i Smallest circumscribed radius axis-4.
Continues on next pageProduct specification - IRB 6700 713HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.6 Fitting equipment to the robot
Continued
Position of attachment holes - drawing 2
190
90
32
8
CL Axis 5
80
40
100
2x M8 12
B
D
C - C
(2x M
8)
(2x M
8)
A
F G
M
(2x M8)
(M8)
(2x M8)
20)(4x M10 456
B
C
D
B
D
C C
E
K
H
J
2x M8
M8
2x M8
265
465 30
377
50
25
4x M10 20
60
50 33
CL Axis 4
CL Axis 3
CL Axis 2
CL Axis 1
L
xx1300000264
MLKJHGFEDCBA iVariant
13.8500303.5320255186208.580403418433R=456IRB 6700 - 235/2.65
13.8500303.5320255186208.580408423438R=456IRB 6700 - 205/2.80
13.8500303.5320255186208.580403418433R=456IRB 6700 - 175/3.05
13.8500303.5320255186208.580408423438R=456IRB 6700 - 150/3.20
13.8500303.5320255193197113395410425R=440IRB 6700 - 200/2.60
13.8500303.5320255193197113395410425R=440IRB 6700 - 155/2.85
15523.5273.5350265187222.580423438453R=468IRB 6700 - 245/3.00
15523.5273.5350265187222.580423438453R=468IRB 6700 - 300/2.70
15523.5273.5350265187222.580423438453R=468IRB 6700Inv - 300/2.60
Continues on next page72 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.6 Fitting equipment to the robotContinued
MLKJHGFEDCBA iVariant
15523.5273.5350265187222.580423438453R=468IRB 6700Inv - 245/2.90i Smallest circumscribed radius axis-3.
Continues on next pageProduct specification - IRB 6700 733HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.6 Fitting equipment to the robot
Continued
Tool flange, standardBelow is the standard tool flange. The guide pin hole is, in calibration position,pointing upwards in Z-direction.
221
01
12
3x R 0,8 -0,4+2
3x R0,8 0+1
1x45
45°
2,5
A 11x M12
18 H7 + 0,0180
28 + 20
25 min. (H
7)
30°
17
,4 m
in.
1
45°
24
+
20
(Cou
nter
bore
)
68,5
61
18 m
in.
23 m
ax.
B-B
CL C-D
1,6
0,2 A B
0,3 C D
0,2 C D B
12 H7 0+0,018
6x R11
3x R70
16
0
11x 30°
18°A
A
B
B
0,04 AB
1,6
16 ±1
0,5 45° X
M1
2
A-A
20
0h
8-0
,07
20
10
0H
70
+0
,03
5
0,0
2A
xx1300000280
Thread length: 18 mm.A
The turning disc for robot variants IRB 6700 - 200/2.60 and IRB 6700 - 155/2.85was redesigned when Axis Calibration was introduced for IRB 6700. Prior to AxisCalibration the holes on the disc were through. On the current turning disc theholes are not through.
Fastener qualityUse suitable screws and tightening torque for your application, screws with qualityclass 12.9 are recommended.
Continues on next page74 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.6 Fitting equipment to the robotContinued
Tool flange, LeanIDBelow is the tool flange for option 780-4, LeanID. The guide pin hole is, in calibrationposition, pointing upwards in Z-direction.
C - C
A
160
12x 30°
C
C
1
2 H
71
5
11
xM
12
1
8
2
00
h8
8 ( 100 H7)
1x45
1
00
H7
0,0
7E
0,3
EF
F
E
xx1300000290
Thread length: 18 mm.A
Fastener qualityUse suitable screws and tightening torque for your application, screws with qualityclass 12.9 are recommended.
Product specification - IRB 6700 753HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.6 Fitting equipment to the robot
Continued
1.7 Maintenance and troubleshooting
GeneralThe robot requires only minimum maintenance during operation. It has beendesigned to make it as easy to service as possible:
• Maintenance-free AC motors are used.• Oil is used for the gearboxes.• The cabling is routed for longevity, and in the unlikely event of a failure, its
modular design makes it easy to change.
MaintenanceThe maintenance intervals depend on the use of the robot. The requiredmaintenance activities also depend on the selected options. For detailed informationonmaintenance procedures, see themaintenance section in Product manual - IRB6700 and Product manual - IRB 6700Inv.
76 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.7 Maintenance and troubleshooting
1.8 Robot motion
1.8.1 Robot motion
Type of motion
NoteRange of movement- IRB 6700Inv
Range of movement -IRB 6700
Type of motionAxis
±170°±170° or ±220° (option)Rotation motionAxis 1
±65° ii-65°/+85° iArm motionAxis 2
-180° ii /+70° ii-180°/+70°Arm motionAxis 3
±300°±300°Wrist motionAxis 4
±130° iii±130° iiiBend motionAxis 5
±360° iv±360° ivTurn motionAxis 6
Maximum value.±93.7 revolutions±93.7 revolutionsThe default working range foraxis 6 can be extended by chan-ging parameter values in thesoftware.Option 610-1 Independent axiscan be used for resetting the re-volution counter after the axishas been rotated (no need for"rewinding" the axis).
i Working range for variants IRB 6700 - 300/2.70 and - 245/3.00:+85° to -65° when axis 3 is within +70° to -45°+85° to -58° when axis 3 is within +70° to -180°
ii Working ranges of axis 2 and axis 3 are limited in some areas to avoid collision with balancing.iii Working range +120° to -120° for robots with LeanID, option 780-4.iv Working range +220° to -220° for robots with LeanID, option 780-4.
Continues on next pageProduct specification - IRB 6700 773HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motion
Working range axis 2 and axis 3 for IRB 6700-300/2.70 and -245/3.00Limited in some areas to avoid collision with balancing.
xx1700000509
Working range axis 2 and axis 3 for IRB 6700Inv-300/2.60 and -245/2.90Limited in some areas to avoid collision with balancing.
xx1700000510
Continues on next page78 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motionContinued
Working range axis 5 and axis 6 for LeanID, option 780-4Allowed working area for axis 6 related to axis 5 position is shown in the figurebelow.
xx1300001587
Continues on next pageProduct specification - IRB 6700 793HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motion
Continued
Working range
Reach (m)Handling capacity (kg)Robot type
2.65235IRB 6700
1187 920
1908 2650
3114
320
xx1300000281
Continues on next page80 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motionContinued
Reach (m)Handling capacity (kg)Robot type
2.80205IRB 6700
308
3259
1281
2039
958
2794
xx1300000282
Continues on next pageProduct specification - IRB 6700 813HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motion
Continued
Reach (m)Handling capacity (kg)Robot type
2.60200IRB 6700
911 1150
1859 2601
3065
282
xx1300000341
Continues on next page82 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motionContinued
Reach (m)Handling capacity (kg)Robot type
3.05175IRB 6700
1527
2314
1109
3056
726
3520
xx1300000283
Continues on next pageProduct specification - IRB 6700 833HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motion
Continued
Reach (m)Handling capacity (kg)Robot type
2.85155IRB 6700
1352
2106
994
2848
529
3312
xx1300000340
Continues on next page84 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motionContinued
Reach (m)Handling capacity (kg)Robot type
3.20150IRB 6700
1604
2445
1067
3200
713
3665
xx1300000284
Continues on next pageProduct specification - IRB 6700 853HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motion
Continued
Reach (m)Handling capacity (kg)Robot type
2.70300IRB 6700
957 1187
1850 2720
31
54
3
49
xx1400001137
Continues on next page86 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motionContinued
Reach (m)Handling capacity (kg)Robot type
3.00245IRB 6700
2097
1518 1057
2967
59
6
33
99
xx1400001138
Continues on next pageProduct specification - IRB 6700 873HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motion
Continued
Reach (m)Handling capacity (kg)Robot type
2.60300IRB 6700Inv
957
3204
1321
1812 2617
85
xx1700000557
Continues on next page88 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motionContinued
Reach (m)Handling capacity (kg)Robot type
2.90245IRB 6700Inv
2864
162
1057 2060
345
1
1518
xx1700000558
Product specification - IRB 6700 893HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.8.1 Robot motion
Continued
1.8.2 Performance according to ISO 9283
GeneralAt rated maximum load, maximum offset and 1.6 m/s velocity on the inclined ISOtest plane, with all six axes in motion. Values in the table below are the averageresult of measurements on a small number of robots. The result may differdepending on where in the working range the robot is positioning, velocity, armconfiguration, from which direction the position is approached, the load directionof the arm system. Backlashes in gearboxes also affect the result.The figures for AP, RP, AT and RT are measured according to figure below.
xx0800000424
DescriptionPosDescriptionPos
Programmed pathEProgrammed positionA
Actual path at program executionDMean position at programexecution
B
Max deviation from E to average pathATMean distance from pro-grammed position
AP
Tolerance of the path at repeatedprogram execution
RTTolerance of position B at re-peated positioning
RP
150/3.20175/3.05205/2.80235/2.65IRB 6700
0.050.040.060.03Pose accuracy, AP i (mm)
0.060.050.050.05Pose repeatability, RP (mm)
0.340.280.170.16Pose stabilization time, PSt (s) within0.4 mm of the position
1.61.91.51.7Path accuracy, AT (mm)
0.140.120.080.08Path repeatability, RT (mm)i AP according to the ISO test above, is the difference between the teached position (positionmanually
modified in the cell) and the average position obtained during program execution.
Continues on next page90 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
1 Description1.8.2 Performance according to ISO 9283
245/3.00300/2.70155/2.85200/2.60IRB 6700
0.030.070.030.03Pose accuracy, AP i (mm)
0.050.060.080.05Pose repeatability, RP (mm)
0.140.110.190.21Pose stabilization time, PSt (s) within0.4 mm of the position
1.61.41.51.7Path accuracy, AT (mm)
0.120.070.090.11Path repeatability, RT (mm)i AP according to the ISO test above, is the difference between the teached position (positionmanually
modified in the cell) and the average position obtained during program execution.
245/2.90300/2.60IRB 6700Inv
0.060.06Pose accuracy, AP i (mm)
0.060.05Pose repeatability, RP (mm)
0.280.26Pose stabilization time, PSt (s) within 0.4 mm of theposition
1.61.6Path accuracy, AT (mm)
0.220.1Path repeatability, RT (mm)i AP according to the ISO test above, is the difference between the teached position (positionmanually
modified in the cell) and the average position obtained during program execution.
Product specification - IRB 6700 913HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.8.2 Performance according to ISO 9283
Continued
1.8.3 Velocity
Maximum axis speed
Axis 6Axis 5Axis 4Axis 3Axis 2Axis 1Robot type
190 °/s120 °/s170 °/s90 °/s90 °/s100 °/sIRB 6700-235/2.65
190 °/s120 °/s170 °/s90 °/s90 °/s100 °/sIRB 6700-205/2.80
210 °/s150 °/s190 °/s110 °/s110 °/s110 °/sIRB 6700-200/2.60
190 °/s120 °/s170 °/s90 °/s90 °/s100 °/sIRB 6700-175/3.05
210 °/s150 °/s190 °/s110 °/s110 °/s110 °/sIRB 6700-155/2.85
190 °/s120 °/s170 °/s90 °/s90 °/s100 °/sIRB 6700-150/3.20
180 °/s110 °/s140 °/s90 °/s88 °/s100 °/sIRB 6700-300/2.70
180 °/s110 °/s140 °/s90 °/s88 °/s100 °/sIRB 6700-245/3.00
180 °/s110 °/s140 °/s90 °/s88 °/s100 °/sIRB 6700Inv-300/2.60
180 °/s110 °/s140 °/s90 °/s88 °/s100 °/sIRB 6700Inv-245/2.90
There is a supervision function to prevent overheating in applications with intensiveand frequent movements (high duty cycle).
Axis resolution0.001° to 0.005°.
92 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.8.3 Velocity
1.8.4 Robot stopping distances and times
IntroductionThe stopping distances and times for category 0 and category 1 stops, as requiredby EN ISO 10218-1 Annex B, are listed in Product specification - Robot stoppingdistances according to ISO 10218-1 (3HAC048645-001).
Product specification - IRB 6700 933HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.8.4 Robot stopping distances and times
1.9 Cooling fan for axis 1 motor
Option 87-1To be used to avoid overheating of motors and gears in applications with intensivemotion (high average speed and /or high average torque and/or short wait time)of axis 1.Valid protection for cooling fan is IP54. Fan failure stops the robot. The option isnot allowed to select when the robot is placed on a track motion, IRBT.To determine the use of cooling fan for axis 1 motor use the function GearboxHeat Prediction Tool in RobotStudio. Reliable facts for the decision of need forfan or not will be achieved by entering the ambient temperature for a specific cycle.Contact your local ABB organization.
94 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.9 Cooling fan for axis 1 motor
1.10 Servo gun
1.10.1 Introduction
GeneralThe robot can be supplied with hardware and software for control of the followingconfigurations:
• Stationary Gun• Robot Gun• Robot Gun and Track Motion• Track Motion
The specific parts related to the servo motor control for electrical welding gunsand for track motion configurations are shown in the conceptual pictures below.The major parts and required options are also stated in the configurations listsbelow each picture.The cables for control of the basic robot are shown in the pictures with dotted lines.
Product specification - IRB 6700 953HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.10.1 Introduction
1.10.2 Stationary gun
General
xx1000000507
OptionsOptions according to the table below are required to complete the delivery. Forfurther details on each option see corresponding product specification.
Product specifica-tion
DescriptionOption
Stationary gun. This option includes cable G (7 mlength) for resolver signals from robot base (FB7)to stationary gun/axis 7.
785-5
Resolver connection, axis 7, on base.864-1
Product specifica-tion - ControllerIRC5
First additional drive. Drive unit for 7th axis withcorresponding cables assembled inside drive mod-ule.
907-1
Connection to first drive.786-1, -2, -3, -4Cable A (7-30m) between drivemodule and station-ary gun/axis 7 for servo drive power.
Product specifica-tion - ControllerIRC5
Spot 6. This option includes Spot Servo and SpotServo Equalizing.
635-6
96 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.10.2 Stationary gun
1.10.3 Robot gun
General
xx1000000506
OptionOptions according to table below are required to complete the delivery. For furtherdetails on each option see corresponding product specification.
Product specificationDescriptionOption
Robot gun. This option includes cables withinmanipulator for servo power signals (servogun/axis 7).
785-1
Product specifica-tion - Controller IRC5
First additional drive. Drive unit for 7th axis withcorresponding cables assembled inside drivemodule.
907-1
Connection to first drive. Cable A (7-30 m)between drive module and robot base for servodrive power.
786-1, -2, -3, -4
Product specifica-tion - Controller IRC5
Spot 6, Spot Servo, or Spot Servo Equalizing.635-6
Product specification - IRB 6700 973HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.10.3 Robot gun
1.10.4 Robot gun and track motion
General
Axis 7
M
Drive
Module
B
SMB
Axis 8F
E
Control
Module
FB7
SMB
xx1000000505
OptionsOptions according to table below are required to complete the delivery. For furtherdetails on each option see corresponding product specification.
Product specificationDescriptionOption
Product specifica-tion - IRBT4004/6004/7004
Robot Gun - Track Motion. This option in-cludes cables within manipulator for servopower signals (servo gun/axis 7).
785-1 +1002-2 i
Product specifica-tion - IRBT4004/6004/7004
Serial measurement box (SMB2, Split box)for distribution of servo power to axis 8.The box is placed on the track motion.
Track motion deliv-ery includes
Cables from serial measurement box to trackmotion.Cable B for servo power (1.5 m length).Connection to first and second drive.Cable E and F (7-22m) between drivemoduleand serial measurement box for dual servodrive power/resolver signals.
Product specifica-tion - Controller IRC5
First additional drive. Drive unit for 7th axiswith corresponding cables assembled insidedrive module.
907-1
Product specifica-tion - Controller IRC5
Second additional drive. Drive unit for 8thaxis with corresponding cables assembledinside drive module.
907-1
Product specifica-tion - Controller soft-ware IRC5
Spot 6, Spot Servo, or Spot Servo Equalizing.635-6
Resolver connection, axis 7, on base (FB7).864-1i To specify robot on track equipped with servo gun. Option 1002-2 from specification form for track
motion.
98 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.10.4 Robot gun and track motion
1.10.5 Track motion
GeneralThe robot can be supplied with a track motion, see Product specification - IRBT4004/6004/7004. For configuration and specification of hardware see the followingfigure.
SMB
Drive
Module
Control
ModuleMAxis 7
E
FB7
xx1000000504
OptionsOptions according to table below are required to complete the delivery. For furtherdetails on each option see corresponding product specification.
Product specificationDescriptionOption
Product specifica-tion - IRBT4004/6004/7004
Serial measurement (SMB) in manipulator isused, together with option 864-1, FB7 for signalsto axis 7/Track motion.
Track motiondelivery in-cludes
Cable E for between Drive Module and trackmotion servo for drive power.
First additional drive. Drive unit for 7th axis withcorresponding cables assembled inside drivemodule.
907-1
Resolver connection, axis 7, on base (FB7).864-1
Product specification - IRB 6700 993HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
1 Description1.10.5 Track motion
This page is intentionally left blank
2 DressPack and SpotPack2.1 Introduction
2.1.1 Included options
DressPackIncludes options for upper arm, lower arm and floor pos C, D and E, see thefollowing figure. These are described separately below but are designed as acomplete package for various applications.The DressPack for the floor contains customer signals.The DressPack for upper and lower arm contains process cable packages includingsignals, process media (water and/or air) and power feeding (for spot weldingpower) for customer use.Necessary supports and brackets are also included.The routing of the process cable package on the robot is available in differentconfigurations.
Note
Include everywhere that this is also for IRB 6700Inv (e.g. "This is available forall IRB 6700 and IRB 6700Inv versions").
Continues on next pageProduct specification - IRB 6700 1013HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.1.1 Included options
SpotPackThe package supplies the transformer gun/gripper with necessary media, such ascompressed air, cooling water and electrical power. It includes the above describedDressPack + Spot Welding cabinet, Water And Air unit pos A and F (if included)and software, see the following figure.
(A)
(F)
(C)
(D)
(E)
(B)
xx1300001588
DescriptionPos
SpotPack, spot welding cabinetA
Robot controller, (including 7th axis drive for servo gun)B
DressPack, floorC
DressPack, lower armD
DressPack, upper armE
SpotPack, water and air unitF
102 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.1.1 Included optionsContinued
2.1.2 Product range
DressPack solutions for different users needsThe different robot types can be equipped with the well integrated cable and hosepackages in the SpotPack or DressPack options. The DressPack is designed inclose conjunction with the development of the manipulator and is therefore wellsynchronized with the robot.As there is a big span between different users need of flexibility, depending of thecomplexity of the operation/wrist movements, there are two major levels of dresspack solutions available, see Figure below.
External
(MH)
Integrated
(MH/SW)
Complexity in
wrist movements
Performance/
Functionality
Lower flexibility demand
on production line
High flexibility demand
on production line
LeanID, MH/SW 6
MH 3
xx1300000285
IntegratedThis type of dress pack is intended for a production where there are many complexwrist movements and the need for flexibility in changing products is high.Available options are 798-3 and 780-4 for material handling/spot welding, the LeanIDconcept.
ExternalThis type of dress pack is recommended where there are less complexity in wristmovements. This normally occurs when there are not many different productsrunning in the production cell. This package requires more individual adjustmentto optimize towards robot program at set up.Available options are 798-3 and 780-3 for material handling.
Product specification - IRB 6700 1033HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.1.2 Product range
2.1.3 Limitations of robot movements
GeneralWhen using DressPack options on the upper arm the robot movements will belimited.
• In bending backwards positions there are limitations due to interference withmanipulator or Water and Air unit (if such is mounted).
• Might restrict working range, seeWorking range axis 5 and axis 6 for LeanID,option 780-4 on page 79.
Note
For more detail information please contact Serop Product support/SEROP/ABB.E-mail address: [email protected]
Restrictions for LeanID, option 780-4Limitation for axis 5 and 6 depends on how the dress pack is assembled at the tooland how adjustment has been done.
Working rangeAxis
120o to -120oAxis 5
220o to -220oAxis 6
104 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.1.3 Limitations of robot movements
2.1.4 Impact on DressPack lifetime
GeneralThere are some robot movements/positions that shall be avoided in the robotproduction program. This will improve the lifetime significantly of external upperarm DressPack and wear parts e.g. protection hose, hose reinforcement andprotective sleeves.
• The axis 5 movement is not allowed to press the DressPack against the robotupper arm.
• Combined rotation of the wrist axes must be limited so that the DressPackis not wrapped hard against the upper arm.
See the Product Manual for more detailed information and recommended set-upadjustments.
Product specification - IRB 6700 1053HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.1.4 Impact on DressPack lifetime
2.1.5 Information structure
GeneralThe information for SpotPack and DressPack is structured in the following way.The SpotPack and DressPack can be delivered in five versions developed for twodifferent applications. Each type is described in a separate section.
DescriptionOptionSection
DressPack includes general description DressPack withcommon information.
DressPack2.2
Material handling application / DressPack
DescriptionOptionSection
DressPack for Material Handling.Type H2.3
SpotPack for handling the part against electrical servodriven transformer guns stationary mounted.
Type Hse
Spot welding application / SpotPack and DressPack
DescriptionOptionSection
SpotPack for electrical servo driven transformer gunscarried by the robot manipulator.
Type Se2.4
Spot welding cabinet
DescriptionOptionSection
Includes general description of Spot Welding cabinetwith common information.
SpotWeldingCabin-et
2.5
Water and air unit
DescriptionOptionSection
Includes general description of Water and Air unit withcommon information.
Water and Air unit2.6
Connector kits
DescriptionOptionSection
Includes general description of connector kits for Spot-Pack and DressPack.
Connector Kits2.7
106 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.1.5 Information structure
2.2 DressPack
2.2.1 Introduction
Available DressPack configurations for Material HandlingThe table below shows the different DressPack configurations available for MaterialHandling.
Upper armLower arm
Option 780-3, Axis 3 to 6Option 798-3, Base to axis 3Option 778-1,External routingMaterial Handling
Option 780-4, Axis 3 to axis 6(LeanID)Internal routing
Available DressPack configurations for Spot WeldingThe table below shows the different DressPack configurations available for SpotWelding.
Upper armLower arm
Option 780-4, Axis 3 to axis 6(LeanID)
Option 798-3, Base to axis 3External routing
Option 778-2,Spot Welding
Internal routing
Product specification - IRB 6700 1073HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.2.1 Introduction
2.2.2 Built-in features for upper arm DressPack
ExternalMaterial handling (option 780-3):
• Internal routing through the rear part of the upper arm.• Protection hose can easily be replaced if damaged.• One version for all IRB 6700 versions and all IRB 6700Inv versions.• Adjustment for optimal hose/cable lengths.
InternalSpot Welding and Material handling (option 780-4):
• Partly internal routing through the upper arm.• Suitable for complex movements.• High demands for flexibility and accessibility.• Longer lifetime.• Predictable movements.• Easy exchange of DressPack.
108 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.2.2 Built-in features for upper arm DressPack
2.2.3 Interface descriptions for DressPack
GeneralBelow is an overview showing the different DressPack options connection points,and their locations. For detailed information see the circuit diagram, and Productmanual - DressPack/SpotPack IRB 6700.
(B)
(C)
(A)
xx1300000224
OptionsDescriptionLocationPos
864-1, 798-3FB7, CP/CS/CBUSBaseA
798-3CP/CS/CBUSAxis 3B
780-3, 780-4CP/CS/CBUS, WELDAxis 6C
Continues on next pageProduct specification - IRB 6700 1093HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.2.3 Interface descriptions for DressPack
BaseMaterial handling (option 798-3), see figure below:
• Included are: A, B (if applicable), one D (Proc 1) and E (if applicable).Spot welding (option 798-3), see figure below:
• Included are: A, B (if applicable), C, D (Proc 1-4) and E (if applicable).
(A) (C)
(D)
(B)
(E)
xx1000000619
For corresponding parts of the tool, see Connection kits on page 159.
DescriptionPos
R1.CP/CSA
R1.SP (Spot Welding Servo gun) or FB7 (Resolver connection)B
R1.WELD 3x35mm2 . (Spot Welding)C
R1.PROC 1 (Material Handling/Spot Welding 1/2”, M22x1.5, 24 degree seal)DR1.PROC 2 - 4 (Spot Welding 1/2”, M22x1.5, 24 degree seal)
R1.ETHERNET (M12 connector, when EtherNet communication is selected)E
Continues on next page110 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.2.3 Interface descriptions for DressPackContinued
Axis 3Material Handling (option 798-3), see figure below:
• Included are: A, B/G (if applicable) and one C (Proc 1).Spot welding (option 798-3), see figure below:
• Included are: A, D, B/E/F/G (if applicable) and C (Proc 1-4).
(D)
(A)
(E) (B) (F)
(G)
(C)
R2.SP
R2.PROC1
R2.FB
R2.CP/CS R2.ETHERNET R2.CBUS
R2.PROC4 R2.PROC3 R2.PROC2
xx1200000072
For corresponding parts of the tool, see Connection kits on page 159.
DescriptionPos
R2.CP/CSA
R2.ETHERNET (M12 connector, when EtherNet communication is selected)B
R2.PROC 1 (Material Handling 1/2”, M22x1.5, 24 degree seal)CR2.PROC 2-4 (Spot Welding 1/2”, M22x1.5, 24 degree seal)
R2.WELD 3x35mm2 (Spot Welding)D
R2.FB7E
R2.SP (Spot Welding Servo gun)F
R2.CBUS (UTOW connector when Profibus or DeviceNet communication isselected)
G
Continues on next pageProduct specification - IRB 6700 1113HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.2.3 Interface descriptions for DressPack
Continued
Axis 6
ExternalMaterial handling (option 780-3), see figure below:
• Hose and cable free length, min. 1000 mm.• Air hose ends with free end.
The cable ends with a connector, the main parts are described in the list below(for corresponding parts of the tool, see Connection kits on page 159):
xx0900000728
EtherNet connectorMaterial handling (option 780-3), see figure below:
• Cable free length, min. 1000 mm.• Signals are connected with a M12 connector.
The different main parts within the connector are described in the list below, bothwith name and Harting article number (for corresponding parts of the tool, seewithin the Harting product offer).
Harting articleName
21 03 882 1405PIN connector, R3.ETHERNET
61 03 000 0094PIN
3HAC033600-001 ABB articleSealing cap M12x1
xx1100000956
Continues on next page112 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.2.3 Interface descriptions for DressPackContinued
IntegratedMaterial Handling/Spot Welding option 780-4 (LeanID), see figure below:
• Hose and cable free length, min. 1160 mm.• Hoses and weld power cable (only for spot welding) end with free end.
The cable ends with connectors, for corresponding parts of the tool, seeConnectionkits on page 159 and within the UTOW product offer.
(B) (F) (E)(G)(A)
(C)(D)
xx1200000117
DescriptionPos
R3.CP/CS (UTOW connector 26p) Customer signals and powerA
R3.ETHERNET (M12 connector) EtherNet signals (when EtherNet communic-ation is selected)
B
R3.PROC 1-2 (1/2”, freeend) R3.PROC 2-4 (3/8”, free end) Media hosesC
R3.WELD 3x25mm2 (Free end) Spot Welding powerD
R3.FB7 (M23 connector 17p) Servo motor feedback (when Spot WeldingServo gun is selected)
E
R3.SP (M23 connector 8p) Servo motor power (when Spot Welding Servogun is selected)
F
R3.CBUS (UTOW connector 10p) BUS signals (when Profibus or DeviceNetcommunication is selected)
G
Product specification - IRB 6700 1133HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.2.3 Interface descriptions for DressPack
Continued
2.2.4 Dimensions
Dimensions for robot with DressPackDimensions are shown in figures below.
323 520
xx1300000286
Axis 3 to axis 6 (option 780-3)
650 360
580
600120
xx1300000287
Base to axis 3 + Axis 3 to axis 6 (option 798-3 + 780-4)
114 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.2.4 Dimensions
2.3 Type H/HSe
2.3.1 Introduction
GeneralVariant Type H is designed for Material Handling (MH) application and Hse tohandling parts against a stationary Spot Welding gun (pneumatic or servocontrolled). Included modules are shown in Figure below.
(A)
(B)
(C)
(D)
(E)
(G)
(H)
(F)
xx1300002178
NamePos
For type HSeSpot Welding cabinetA
Incl. 7:th axis drive for servo gun, HSeRobot Cabinet IRC5B
DressPack, FloorC
DressPack, Lower armD
Water and Air unit with hosesE
For type H and HSeDressPack, Upper armF
Robot GripperG
Pneumatic or servo controlled and HSeStationary gunH
Available configurations with linked option numbers are described below.
Continues on next pageProduct specification - IRB 6700 1153HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.1 Introduction
Option description
DescriptionTypeOption
Floor cables and connections inside the I/O sectionfor the DressPack are chosen. The length and con-figuration of the floor harness is specified under theoptions below.
Connection to cabinet16-1
Option 94-X for parallel communication.Option 90-X for parallel communication and field buscommunication with Can/DeviceNet.Option 92-X for parallel communication and field buscommunication with Profibus.
Offers the signal cables needed for parallel commu-nication in lower and upper arm DressPack. To becombined with option 94-X.
Parallel communication455-1
Offers the signal cables needed for the combinationof parallel and bus communication in lower and up-per arm DressPack. To be combined with option 90-X or 92-X.
Parallel andBus communic-ation
455-4
Offers the signal cables needed for the bus commu-nication in lower and upper arm DressPack. To becombined with option 859-X. Requires selection ofoption 94-X.
Parallel and Ethernet com-munication
455-8
The available alternatives and allowed combinations are shown in the schematicFigures below.
Option 778-1Option 94-XOption 455-1Applicatioon Inter-face connected to Material HandlingCable length,Parallel communicationOption 16-1, Cabinet Parallel communication
Option 90-XOption 455-4Option 92-XParallel and bus commu-
nication Cable length, Paralleland bus communication
Option 859-XOption 455-8Cable length, Ethernetcommunication
Parallel and Ethernetcommunication
DressPack
Upper armLower arm
Option 780-3, Axis 3 to 6Option 798-3, Base to axis 3Option 778-1.External routingMaterial Handling
Option 780-4, Axis 3 to 6Internal routing
116 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.1 IntroductionContinued
2.3.2 Configuration result for Type H HSe
GeneralDepending on the choice of options above the DressPackwill have different content.The choice of routing will not affect the content. See tables for signal content below.
DressPack Type H/HSe. Parallel communication• Option 16-1 with Connection to cabinet• (Option 94-X to specify cable length)• Option 455-1. Parallel communication• Option 778-1. Material Handling• Option 798-3. Internal routing, DressPack Lower arm
One of the options:• Option 780-3 (and Option 798-3). External routing• Option 780-4 (and option 798-3) Internal routing
The table below shows the available type of wires/media.
Allowed capacityCable/partarea
At connectionpoint. Base, Ax-is 3 or axis 6
At terminalsin cabinet
Type
Customer Power (CP)
250 VAC, 5 A rmsi
0.75 mm22+22+2Utility Power
250 VAC i0.75 mm21Protective earth
Customer Signals (CS)
50 V DC, 1 A rms0.2 mm212 (6x2) ii12Signals twisted pair
50 V DC, 1 A rms0.2 mm28 (4x2)8Signals twisted pair andseparate shielded
Media
Max. air pressure16 bar/230 PSI
12.5 mminner dia-meter
1Air (PROC 1)
i For option 780-3 50 VAC / 60 VDC.ii For option 780-3 8 signals.
Continues on next pageProduct specification - IRB 6700 1173HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.2 Configuration result for Type H HSe
DressPack Type H/HSe. Parallel and field bus communication, Can/DeviceNet• Option 16-1 with Connection to cabinet• (Option 90-X to specify cable length)• Option 455-4. Parallel and bus communication• Option 778-1 Material Handling• Option 798-3. Internal routing, DressPack Lower arm
One of the options:• Option 780-3 (and Option 798-3). External routing• Option 780-4 (and option 798-3). Internal routing
The table below shows the available type of wires/media.
Allowed capacityCable/partarea
At Connectionpoint. Base, Ax-is 3 or axis 6
At terminalsin cabinet
Type
Customer Power (CP)
250 VAC, 5 A rmsi
0.75 mm22+22+2Utility Power
250 VAC i0.75 mm21Protective earth
Customer Signals (CS)
50 V DC, 1 A rms0.2 mm212 (6x2) ii12Signals twisted pair
50 V DC, 1 A rms0.2 mm28 (4x2)8Signals twisted pair andseparate shielded
Customer bus (CBus)
Can/DeviceNetspec
0.14 mm22At bus boardBus signals
50 V DC, 1 A rms0.2 mm22At bus boardBus signals
Media
Max. air pressure16 bar/230 PSI
12.5 mminner dia-meter
1Air (PROC 1)
i For option 780-3 50 VAC / 60 VDC.ii For option 780-3, 8 signals instead of 12.
Continues on next page118 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.2 Configuration result for Type H HSeContinued
DressPack Type H/HSe. Parallel and field bus communication, Profibus• Option 16-1 with Connection to cabinet• (Option 92-X to specify cable length)• Option 455-4. Parallel and bus communication• Option 778-1. Material Handling• Option 798-3. Internal routing, DressPack Lower arm
One of the options:• Option 780-3 (and Option 798-3). External routing• Option 780-4 (and option 798-3) Internal routing
The table below shows the available type of wires/media.
Allowed capacityCable/partarea
At connectionpoint. Base, Ax-is 3 or axis 6
At terminalsin cabinet
Type
Customer Power (CP)
250 VAC, 5 A rmsi
0,75 mm22+22+2Utility Power
250 VAC i0,75 mm21Protective earth
Customer Signals (CS)
50 V DC, 1 A rms0,2 mm212 (6x2) ii12Signals twisted pair
50 V DC, 1 A rms0,2 mm28 (4x2)8Signals twisted pair andseparate shielded
Customer bus (CBus)
Profibus 12 Mbit/sspec
0,14 mm24At bus boardBus signals
Media
Max. air pressure16 bar/230 PSI
12,5 mminner dia-meter
1Air (PROC 1)
i For option 780-3 50 VAC / 60VDC.ii For option 780-3, 8 singals instead of 12.
Continues on next pageProduct specification - IRB 6700 1193HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.2 Configuration result for Type H HSe
Continued
DressPack Type H/HSe. Parallel and field bus communication, Ethernet• Option 16-1 with Connection to cabinet• (Option 859-X to specify cable length)• (Option 94-X to specify cable length)• Option 455-8. Parallel and Ethernet communication• Option 778-1. Material Handling• Option 798-3. Internal routing, DressPack Lower arm
One of the options:• Option 780-3 (and Option 798-3). External routing• Option 780-4 (and option 798-3) Internal routing
The table below shows the available type of wires/media.
Allowed capacityCable/partarea
At connectionpoint. Base,Axis 3 or axis 6
At termin-als in cabin-et
Type
Customer Power (CP)
250 VAC, 5 A rms i0.75 mm22+22+2Utility Power
250 VAC i0.75 mm21Protective earth
Customer Signals (CS)
50 V DC, 1 A rms0.2 mm212 (6x2) ii12Signals twisted pair
50 V DC, 1 A rms0.2 mm28 (4x2)8Signals twisted pair andseparate shielded
Customer bus (Ethernet)
Ethernet CAT 5e, 100Mbit iii
0.4 mm244Bus signals
Media
Max. air pressure 16bar/230 PSI
12.5 mminner dia-meter
1Air (PROC 1)
i For option 780-3 50 VAC / 60 VDC.ii For option 780-3, 8 signals instead of 12.iii Ethernet with wire colors according to PROFINET standard, M12-connectors.
Continues on next page120 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.2 Configuration result for Type H HSeContinued
Required general options for Type HSeTo enable the SpotPack IRB 6700 to perform as intended, general standard robotoptions are required. These standard options are further described under otherchapters and are also mentioned in this chapter.
• Option 727-1. 24V 8 Amps power supply• Option 635-6. Spot. Software option for pneumatic guns
Required additional options for servo gun Type HSeTo enable the spot welding function package SpotPack IRB 6700 to run with aservo controlled gun, some additional (additional to those described in Requiredgeneral options for Type HSe on page121) servo drive options are required. Thesestandard options are described under other chapters and are alsomentioned belowin this chapter.
• Option 907-1. First additional drive• Option 864-1. Resolver connection, axis 7• Option 785-5. Stationary gun• Option 786-1,-2,-3,-4. Connection to first drive (Cable length to be stated)• Option 635-6. Spot 6
Also option 630-1, Servo tool change, should be used if servo gun tool change isrequired.
Required Spot Welding cabinet options for Type HSeThe SpotPack IRB 6700 also requires a Spot Welding cabinet (option 768-4) toperform as intended. Weld timer brand and weld capacity are stated by choosingthe variant. Additional features could then be added to the cabinet variant. All theseoptions are further described under Spot Welding cabinet on page143 but are alsomentioned in this chapter.
xx1000000381
Continues on next pageProduct specification - IRB 6700 1213HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.2 Configuration result for Type H HSe
Continued
DescriptionTypeOption
This option gives a basic Spot Welding cabinetequipped with a weld timer fromBoschwith an integ-rated inverter with basic capacity. Type Bosch PSI61C0.751OEM.
Bosch MFDC ProfiNet782-13
Additional options to the Spot Welding cabinet are mentioned below. For furthertechnical details as well as restrictions in combinations see Spot Welding cabineton page 143
DescriptionTypeOption
Offers a cooling fan with housing placed on the rearof the Spot Welding cabinet which forces air on thecooling surface/grids of the thyristor or MFDC invert-er.
Forced air cooling788-1
Offers an earth fault protection integrated with thecircuit breaker for the weld power.
Earth fault protection unit789-1
Offers a weld contactor with necessary wiring placedinside the Spot Welding cabinet.
Contactor for weld power790-1
Offers floor cable of 7 m length for weld power.Weld power cable, 7 m791-1
Offers floor cable of 15 m length for weld power.Weld power cable, 15 m791-2
Offers floor cable of 7 m length for process signalsbetween the Spot Welding cabinet and to the station-ary gun.
Process cable to stationarygun, 7 m
809-1
Offers floor cable of 15 m length for process signalsbetween the Spot Welding cabinet and to the station-ary gun.
Process cable to stationarygun, 15 m
809-2
Offers additional functionality for adaptive weldingregulation. Only possible with option 782-11.
Bosch Adaptive control858-1
122 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.2 Configuration result for Type H HSeContinued
2.3.3 Interface description for stationary gun
GeneralThe interface towards the stationary gun includes 3 common parts and 2 extra forservo gun.Common parts:
• Signal interface with a signal connector type modular Harting(Cable option 809-1, -2).
• Power cable with a Multi Contact interface (Cable option 791-1 or option791-2)(Ending Multi contact type MC TSB 150/35).
• Water and air connections made by the customer directly on the water andair unit. SeeWater and air unit on page 151.
Extra for servo gun:• Servo power cable (Option 786-1,-2,-3 or -4). Cable goes from robot control
cabinet to stationary gun and ends with a 23 pin Souriau connector (TypeUT 061823SH).
• Resolver signal cable, 7 m length (included in option 785-5). Cable goes fromrobot foot R3.FB7 to stationary gun and ends with 8 pin Souriau connector(Type UT 06128SH)
The connector configurations are described in the circuit diagram.The Harting connector is shown below. The differentmain parts within the connectorare showed both with name and Harting article number. Corresponding parts atthe tool are available within the Harting product offer.
Harting article No.Name
09 30 010 0543Hood
09 14 010 0303Hinged frame, hood
09 14 025 3101Multicontact, female (HD)
09 14 012 3101Multicontact, female (DD)
09 14 008 3101Multicontact, female (EE)
For the contacts above corresponding female crimp-contacts for the different cablediameters are required.
Continues on next pageProduct specification - IRB 6700 1233HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.3 Interface description for stationary gun
Required Water and Air unit options for Type HSeThe SpotPack IRB 6700 also requires Water and Air unit options to perform asintended. These options are further described underWater and air unit on page151and are also mentioned in this chapter.
xx1700001596
xx1700001597
Continues on next page124 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.3 Interface description for stationary gunContinued
DescriptionTypeOption
Offers the basic water and air unit for type HS includ-ing splitbox for signal distribution.
Water and Air unit, type HS792-2
Offers an additional water return circuit.Second water return793-1
Offers floor cable of 7 m length for signals betweenthe cabinet and to the split box placed on the waterand air unit.
Cable to split box, 7 m797-1
Offers floor cable of 15 m length for signals betweenthe cabinet and to the split box placed on the waterand air unit.
Cable to split box, 15 m797-2
Offers floor cable of 22 m length for signals betweenthe cabinet and to the split box placed on the waterand air unit.
Cable to split box, 22 m797-3
Offers floor cable of 30 m length for signals betweenthe cabinet and to the split box placed on the waterand air unit.
Cable to split box, 30 m797-4
Product specification - IRB 6700 1253HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.3 Interface description for stationary gun
Continued
2.3.4 Summary common options Type H HSe
GeneralThe following options are theminimum required to form a complete SpotPack TypeH/HSe:
• Option 16-1. Connection to cabinet (Cable length and communication typeto be stated)
• Option 455-1, 455-4 or 455-8. Parallel, Parallel and Bus communication orEtherNet (Communication type to be stated)
• Option778-1. Material Handling• Option 798-3. DressPack Lower arm (Routing type to be stated)• Option 780-3, -4. DressPack Upper arm (Routing type to be stated)
126 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.4 Summary common options Type H HSe
2.3.5 Summary options required for Type HSe
General options• Option 727-1. 24V 8 Amps power supply• Option 635-6. Spot (only for type HS)
Servo gun• Option 907-1. First additional drive• Option 785-5. Stationary gun• Option 786-1. Connection to first drive (other lengths available)• Option 635-6. Spot 6
Spot Welding cabinet• Option 768-4. Spot Welding large• Option 782-13. Weld timer capacity• Option 791-1. Power cable 7 m (other lengths available)• Option 809-1. Process cable to stationary gun (other lengths available)
Water and air unit• Option 792-2. Water and air unit, Type HS• Option 797-1. Splitbox cable 7 m. (other lengths available)
Other described options depend on specific system need and performance.
Product specification - IRB 6700 1273HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.3.5 Summary options required for Type HSe
2.4 Type Se
2.4.1 Introduction
GeneralVariant Type Se is designed for robot handled servo-controlled tool (electrical gun).Included modules are shown in Figure below. Available configurations with linkedoption numbers are described below.
(A)
(B)
(C)
(D)
(E)
(F)
xx1300002179
NamePosition
Spot Welding cabinetA
Robot Cabinet IRC5 (including 7th axis drive), SeB
DressPack, FloorC
DressPack, Lower armD
DressPack, Upper armE
Water and Air unit with hosesF
Available configurations with linked option numbers are described below. To achivethe specific servo motor connections within the DressPack for Type Se option785-1 Robot gun must also to be chosen. See Robot gun on page 97 for details.
Continues on next page128 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.1 Introduction
Option description
DescriptionTypeOption
Floor cables and connections inside the I/Osection for the DressPack are chosen. The lengthand configuration of the floor harness is specifiedunder the options below.
Connection to cabinet16-1
Option 94-X for parallel communicationOption 90-X for parallel communication and fieldbus communication with Can/DeviceNetOption 92-X for parallel communication and fieldbus communication with Profibus
Offers the signal cables needed for parallelcommunication in lower and upper armDressPack. To be combined with option 94-X.
Parallel communication455-1
Offers the signal cables needed for the combin-ation of parallel and bus communication incombination in lower and upper arm DressPack.To be combined with option 90-X or 92-X.
Parallel and Bus communica-tion
455-4
Offers the signal cables needed for the Ethernetcommunication in combination in lower and up-per arm DressPack. To be combined with option859-X. Requires selection of option 94-X.
Parallel and Ethernet455-8
Option 778-2,Option 94-XOption 455-1, Parallelcommunication
Application Interfaceconnected to Spot WeldingCable length, Parallel
communicationOption 16-1, Cabinet
Option 90-XOption 455-4, Paralleland Bus communica-tion
Option 92-XCable length, Paralleland Bus communica-tion
Option 859-XOption 455-8, Paralleland Ethernet commu-nication
Cable length, Ethernetcommunication
DressPack
Upper armLower arm
Option 780-4, Axis 3 to 6Option 798-3, Base to axis 3Option 778-2Internal routingExternal routingSpot Welding
Product specification - IRB 6700 1293HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.1 Introduction
Continued
2.4.2 Configuration result for Type Se
GeneralDepending on the choice of options above (combined with option 785-1 Robot gun)the DressPack will have different content. The choice of routing will not affect thecontent. See tables for signal content below.
DressPack Type Se. Parallel communication• Option 16-1 with Connection to cabinet• (Option 94-X to specify cable length)• Option 455-1. Parallel communication• Option 778-2. Spot Welding• Option 798-3. External routing, DressPack Lower arm
and:• Option 780-4 (and Option 798-3). Internal routing, DressPack Upper arm
The table below shows the available type of wires/media for type S.
Allowed capacityCable/partarea
At connectionpoint. Base, ax-is 3 or axis 6
At terminalsin cabinet
Type S
Customer Power (CP)
250 VAC, 5 A rms0.75 mm22+22+2Utility Power
250 VAC0.75 mm21Protective earth
Customer Signals (CS)
50 V DC, 1 A rms0.2 mm212 (6x2)12Signals twisted pair
50 V DC, 1 A rms0.2 mm28 (4x2)8Signals twisted pair andseparate shielded
Media
Max. air pressure16 bar/ 230 PSI
12.5 mminner
4Water/Air (PROC 1-4)
Max. water pres-sure 10 bar/ 145PSI
diameter i
Welding power (WELD)
600 VAC, 150 Arms at 20°C (68°F)
35 mm2 ii2Lower and Upper arm
1Protective earth (Lower andUpper arm)i For LeanID 2x1/2" + 2x3/8", only upper armii For LeanID upper arm 25 mm2 , only upper arm, 135 A rms
Continues on next page130 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.2 Configuration result for Type Se
The table below shows the available type of wires/media for type Se.
Allowed capacityCable/partarea
At connectionpoint. Base, ax-is 2/3 or axis 6
At terminalsin cabinet
Type Se
Customer Power (CP)
250 VAC, 5 A rms0.75 mm22+22+2Utility Power
250 VAC0.75 mm21Protective earth
Customer Signals (CS)
50 V DC, 1 A rms0.2 mm212 (6x2)12Signals twisted pair
50 V DC, 1 A rms0.2 mm28 (4x2)8Signals twisted pair andseparate shielded
Servo motor signals
600 VAC, 12 A rms1.5 mm23At driveServo motor power
600 VAC1.5 mm21At driveProtective earth
50 V DC, 1 A rms0.23 mm26-Signals twisted pair for re-solver
50 V DC, 1 A rms0.23 mm22-Brake
50 V DC, 1 A rms0.23 mm22-Temperature control/PTC
Media
Max. air pressure16 bar/ 230 PSI.
12.5 mminner dia-meter i
4Water/Air (PROC 1-4)
Max. water pres-sure 10 bar/ 145PSI
Welding power (WELD)
600 VAC,35 mm2 ii2Lower and Upper arm150 A rms at 20°C(68°F)1Protective earth (Lower and
Upper arm)i For LeanID 2x1/2" + 2x3/8", only upper armii For LeanID upper arm 25 mm2 , only upper arm, 135 A rms
Continues on next pageProduct specification - IRB 6700 1313HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.2 Configuration result for Type Se
Continued
DressPack Type Se. Parallel and field bus communication, Can/DeviceNet• Option 16-1 with Connection to cabinet• (Option 90-X to specify cable length)• Option 455-4. Parallel and bus communication• Option 778-2. Spot Welding• Option 798-3. External routing, DressPack Lower arm
and:• Option 780-4 (and option 798-3). Internal routing, DressPack Upper arm
The table below shows the available type of wires/media for type S.
Allowed capacityCable/partarea
At connectionpoint. Base, ax-is 3 or axis 6
At terminalsin cabinet
Type S
Customer Power (CP)
250 VAC, 5 A rms0.75 mm22+22+2Utility Power
250 VAC0.75 mm21Protective earth
Customer signals (CS)
50 V DC, 1 A rms0.2 mm212 (6x2)12Signals twisted pair
50 V DC, 1 A rms0.2 mm28 (4x2)8Signals twisted pair andseparate shielded
Customer bus (CBus)
Can/DeviceNetspec
0.14 mm22At bus boardBus signals
50 V DC, 1 A rms0.23 mm22At bus boardBus signals
Media
Max. air pressure16 bar/230 PSI
12.5 mminner dia-meter i
4Water/Air (PROC 1-4)
Max. water pres-sure 10 bar/145PSI.
Welding power (WELD)
600 VAC,35 mm2 ii2Lower and Upper arm150 A rms at 20°C(68°F)1Protective earth (Lower and
Upper arm)i For LeanID 2x1/2" + 2x3/8", only upper armii For LeanID upper arm 25 mm2 , only upper arm, 135 A rms
Continues on next page132 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.2 Configuration result for Type SeContinued
The table below shows the available type of wires/media for type Se.
Allowed capacityCable/partarea
At connectionpoint. Base, ax-is 3 or axis 6
At terminalsin cabinet
Type Se
Customer Power (CP)
250 VAC, 5 A rms0.75 mm22+22+2Utility Power
250 VAC0.75 mm21Protective earth
Customer signals (CS)
50 V DC, 1 A rms0.2 mm212 (6x2)12Signals twisted pair
50 V DC, 1 A rms0.2 mm24 (2x2)4Signals twisted pair andseparate shielded
Customer bus (CBus)
Can/DeviceNetspec
0.14 mm22At bus boardBus signals
50 V DC, 1 A rms0.23 mm22At bus boardBus signals
Servo motor signals
600 VAC, 12 A rms1.5 mm23At driveServo motor power
600 VAC1.5 mm21At driveProtective earth
50 V DC, 1 A rms0.23 mm26-Signals twisted pair for re-solver
50 V DC, 1 A rms0.23 mm22-Brake
50 V DC, 1 A rms0.23 mm22-Temperature control/PTC
Media
Max. air pressure16 bar/230 PSI.
12.5 mminner dia-meter i
4Water/Air (PROC 1-4)
Max. water pres-sure 10 bar/145PSI.
Welding power (WELD)
600 VAC,35 mm2 ii2Lower and Upper arm150 A rms at 20°C(68°F)1Protective earth (Lower and
Upper arm)i For LeanID 2x1/2" + 2x3/8", only upper armii For LeanID upper arm 25 mm2 , only upper arm, 135 A rms
Continues on next pageProduct specification - IRB 6700 1333HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.2 Configuration result for Type Se
Continued
DressPack Type Se. Parallel and field bus communication, Profibus• Option 16-1 with Connection to cabinet• (Option 92-X to specify cable length)• Option 455-4. Parallel and bus communication• Option 778-2. Spot Welding• Option 798-3. External routing, DressPack Lower arm
and:• Option 780-4 (and option 798-3). Internal routing, DressPack Upper arm
The table below shows the available type of wires/media for type S.
Allowed capacityCable/partarea
At connectionpoint. Base, ax-is 3 or axis 6
At terminalsin cabinet
Type S
Customer Power (CP)
250 VAC, 5 A rms0,75 mm22+22+2Utility Power
250 VAC0,75 mm21Protective earth
Customer signals (CS)
50 V DC, 1 A rms0,2 mm212 (6x2)12Signals twisted pair
50 V DC, 1 A rms0,2 mm28 (4x2)8Signals twisted pair andseparate shielded
Customer bus (CBus)
Profibus 12 Mbit/sspec
0,14 mm24At bus boardBus signals
Media
Max. air pressure16 bar/230 PSI
12,5 mminner dia-meter i
4Water/Air (PROC 1-4)
Max. water pres-sure 10 bar/145PSI.
Welding power (WELD)
600 VAC,35 mm2 ii2Lower and Upper arm150 A rms at 20°C(68°F)1Protective earth (Lower and
Upper arm)i For LeanID 2x1/2" + 2x3/8", only upper armii For LeanID upper arm 25 mm2 , only upper ar, 135 A rms
Continues on next page134 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.2 Configuration result for Type SeContinued
The table below shows the available type of wires/media for type Se.
Allowed capacityCable/partarea
At connectionpoint. Base, ax-is 3 or axis 6
At terminalsin cabinet
Type Se
Customer Power (CP)
250 VAC, 5 A rms0,75 mm22+22+2Utility Power
250 VAC0,75 mm21Protective earth
Customer signals (CS)
50 V DC, 1 A rms0,2 mm212 (6x2)12Signals twisted pair
50 V DC, 1 A rms0,2 mm24 (2x2)4Signals twisted pair andseparate shielded
Customer bus (CBus)
Profibus 12 Mbit/sspec
0,14 mm26 (3x2)At bus board6
Bus signals
Servo motor signals
600 VAC, 12 A rms1,5 mm23At driveServo motor power
600 VAC1,5 mm21At driveProtective earth
50 V DC, 1 A rms0,23 mm26-Signals twisted pair for re-solver
50 V DC, 1 A rms0,23 mm22-Brake
50 V DC, 1 A rms0,23 mm22-Temperature control/PTC
Media
Max. air pressure16 bar/230 PSI.
12,5 mminner dia-meter i
4Water/Air (PROC 1-4)
Max. water pres-sure 10 bar/145PSI.
Welding power (WELD)
600 VAC,35 mm2 ii2Lower and Upper arm150 A rms at 20°C(68°F)1Protective earth (Lower and
Upper arm)i For LeanID 2x1/2" + 2x3/8", only upper armii For LeanID upper arm 25 mm2 , only upper arm, 135 A rms
Continues on next pageProduct specification - IRB 6700 1353HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.2 Configuration result for Type Se
Continued
DressPack Type Se. Parallel and field bus communication, Ethernet• Option 16-1 with Connection to cabinet• (Option 859-X to specify cable length)• (Option 94-X to specify cable length)• Option 455-8. Parallel and Ethernet communication• Option 778-2. Spot Welding• Option 798-3. External routing, DressPack Lower arm
and:• Option 780-4 (and Option 798-3). Internal routing, DressPack Upper arm
The table below shows the available type of wires/media for type S.
Allowed capacityCable/partarea
At connectionpoint. Base, ax-is 3 or axis 6
At terminalsin cabinet
Type S
Customer Power (CP)
250 VAC, 5 A rms0.75 mm22+22+2Utility Power
250 VAC0.75 mm21Protective earth
Customer signals (CS)
50 V DC, 1 A rms0.2 mm212 (6x2)12Signals twisted pair
50 V DC, 1 A rms0.2 mm28 (4x2)8Signals twisted pair andseparate shielded
Customer bus (Ethernet)
Ethernet CAT 5e,100 Mbit i
0.4 mm244Bus signals
Media
Max. air pressure16 bar/230 PSI
12.5 mminner dia-meter ii
4Water/Air (PROC 1-4)
Max. water pres-sure 10 bar/145PSI.
Welding power (WELD)
600 VAC,35 mm2 iii2Lower and Upper arm150 A rms at 20°C(68°F)1Protective earth (Lower and
Upper arm)i Ethernet with wire colors according to PROFINET standard, M12-connectors.ii For LeanID 2x1/2" + 2x3/8"iii For LeanID upper arm 25 mm2 , 135 A rms
Continues on next page136 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.2 Configuration result for Type SeContinued
The table below shows the available type of wires/media for type Se.
Allowed capacityCable/partarea
At connectionpoint. Base, ax-is 2/3 or axis 6
At terminalsin cabinet
Type Se
Customer Power (CP)
250 VAC, 5 A rms0.75 mm22+22+2Utility Power
250 VAC0.75 mm21Protective earth
Customer signals (CS)
50 V DC, 1 A rms0.2 mm212(6x2)12Signals twisted pair
50 V DC, 1 A rms0.2 mm28 (4x2)8Signals twisted pair andseparate shielded
Customer bus (Ethernet)
Ethernet CAT 5e,100 Mbit i
0.4 mm244Bus signals
Servo motor signals
600 VAC, 12 A rms1.5 mm23At driveServo motor power
600 VAC1.5 mm21At driveProtective earth
50 V DC, 1 A rms0.23 mm26-Signals twisted pair for re-solver
50 V DC, 1 A rms0.23 mm22-Brake
50 V DC, 1 A rms0.23 mm22-Temperature control/PTC
Media
Max. air pressure16 bar/230 PSI.
12.5 mminner dia-meter ii
4Water/Air (PROC 1-4)
Max. water pres-sure 10 bar/145PSI.
Welding power (WELD)
600 VAC,35 mm2 iii2Lower and Upper arm150 A rms at 20°C(68°F)1Protective earth (Lower and
Upper arm)i Ethernet with wire colors according to PROFINET standard, M12-connectors.ii For LeanID 2x1/2" + 2x3/8"iii For LeanID upper arm 25 mm2 , 135 A rms
Continues on next pageProduct specification - IRB 6700 1373HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.2 Configuration result for Type Se
Continued
Required general options for Type SeTo enable the SpotPack IRB 6700 to perform as intended, general standard robotoptions are required. These standard options are further described under otherchapters and are also mentioned in this chapter.
• Option 727-1. 24V 8 Amps power supply• Option 635-6. Spot. Software option for pneumatic guns
Required options for servo gun, type SeTo enable the spot welding function package SpotPack IRB 6700 to run with aservo controlled gun, some additional (additional to those described in Requiredgeneral options for Type Se on page 138) servo drive options are required. Thesestandard options are described under other chapters and are alsomentioned belowin this chapter.
• Option 907-1. First additional drive• Option 864-1. Resolver connection, axis 7• Option 785-1. Robot Gun• Option 786-1,-2,-3,-4. Connection to first drive (Cable length to be stated)• Option 635-6. Spot 6.
Also option 630-1, Servo tool change, should be added if servo gun tool changeis required.
Required Spot Welding cabinet options for Type SeThe SpotPack IRB 6700 also requires a Spot Welding cabinet (option 768-4) toperform as intended. Weld timer brand and weld capacity are stated by choosingthe variant. Additional features could then be added to cabinet variant. All theseoptions are further described under SpotWelding cabinet on page143 and are alsomentioned in this chapter.
xx1000000381
Continues on next page138 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.2 Configuration result for Type SeContinued
DescriptionTypeOption
This option gives a basic Spot Welding cabinetequipped with a weld timer fromBoschwith an integ-rated inverter with basic capacity. Type Bosch PSI61C0.751OEM.
Bosch MFDC ProfiNet782-13
Additional options to the Spot Welding cabinet are mentioned below. For furthertechnical details as well as restrictions in combinations see Spot Welding cabineton page 143
DescriptionTypeOption
Offers a cooling fan with housing placed on the rearof the Spot Welding cabinet which forces air on thecooling surface/grids of the thyristor or MFDC invert-er.
Forced air cooling788-1
Offers an earth fault protection integrated with thecircuit breaker for the weld power.
Earth fault protection unit789-1
Offers a weld contactor with necessary wiring placedinside the Spot Welding cabinet.
Contactor for weld power790-1
Weld power cable, 7 mWeld power cable, 7 m791-1
Offers floor cable of 15 m length for weld power.Weld power cable, 15 m791-2
Offers additional functionality for adaptive weldingregulation. Only possible with option 782-11.
Bosch Adaptive control858-1
Continues on next pageProduct specification - IRB 6700 1393HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.2 Configuration result for Type Se
Continued
Required Water and Air unit options for Type SeThe SpotPack IRB 6700 also requires Water and Air unit options to perform asintended. These options are further described underWater and air unit on page151and are also mentioned in this chapter.
xx1700001596
xx1700001597
Continues on next page140 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.2 Configuration result for Type SeContinued
DescriptionTypeOption
Offers the basic water and air unit for type S includingsplitbox for signal distribution.
Water and Air unit, type S792-1
Offers an additional water return circuit.Second water return793-1
Offers floor cable of 7 m length for signals betweenthe cabinet and to the split box placed on the waterand air unit.
Cable to split box, 7 m797-1
Offers floor cable of 15 m length for signals betweenthe cabinet and to the split box placed on the waterand air unit.
Cable to split box, 15 m797-2
Offers floor cable of 22 m length for signals betweenthe cabinet and to the split box placed on the waterand air unit.
Cable to split box, 22 m797-3
Offers floor cable of 30 m length for signals betweenthe cabinet and to the split box placed on the waterand air unit.
Cable to split box, 30 m797-4
Product specification - IRB 6700 1413HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.2 Configuration result for Type Se
Continued
2.4.3 Summary common options for Type Se
GeneralThe following options are theminimum required to form a complete SpotPack TypeS/Se:
• Option 16-1. Connection to cabinet, (Cable length and communication typeto be stated)
• Option 455-1, 455-4 or 455-8. Parallel, Parallel and Bus communication orEtherNet (Communication type to be stated)
• Option 778-2. Spot Welding• Option 798-3. External routing, DressPack Lower arm• Option 780-4 Internal routing, DressPack Upper arm
General options• Option 727-1. 24V 8 Amps power supply• Option 635-6. Spot. (only for type S)
Servo gun type Se• Option 907-1. First additional drive• Option 785-1. Robot Gun• Option 786-1,-2,-3,-4. Connection to first drive (cable length to be stated)• Option 635-6. Spot 6
Spot Welding cabinet• Option 768-4. Spot Welding large• Option 782-13. Weld timer capacity• Option 791-1. Power cable 7 m (other length available)
Water and air unit• Option 792-1. Water and air unit, Type S• Option 797-1. Splitbox cable 7 m (other lengths available)
Other described options depend on specific system need and performance.
142 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.4.3 Summary common options for Type Se
2.5 Spot Welding cabinet
2.5.1 Introduction to Spot Welding cabinet
GeneralThe Spot Welding cabinet for SpotPack contains the electric components andcircuits needed for spot welding application. The Spot Welding cabinet, with thewelding controller build in, is controlled from the robot controller via the processorsoftware. The capacity and functionality depends on the choice of different optioncombinations.The Spot Welding cabinet is designed to be placed on top of the robot controllercabinet (Single cabinet version option 700-3), see Figure below. This is also howit is assembled at delivery.
A
C
B
xx1600000525
Spot welding cabinet, mounted on IRC5 controllerA
Continues on next pageProduct specification - IRB 6700 1433HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.5.1 Introduction to Spot Welding cabinet
Spot welding cabinet, standing on the floorB
IRC5 controllerC
There are interface cables between the robot controller cabinet and the SpotWelding cabinet (cable length 1.5 m, connected at rear of the control cabinet andat front of Spot Welding cabinet). These cables includes power feeding for controlcircuits, process signals to the welding gun, safety signals, communication towardsweld timer and I/O:s for indication and control. Depending on chosen options wiringwill differ (see option descriptions below for further details).The Spot Welding cabinet has the following common main features.
• Modular build for easy repair and installation (see Figure below)• Rotary switch with adjustable thermal release and short circuit release• Cross connection of signal handling with separate fusing for different circuits
to achieve selectivity• Programmable weld timer with proportional valve control• A compact cabinet family based on a common platform prepared for additional
options and for easy exchange
Note
Dimensions of the large cabinet within brackets.
xx1700001386
Continues on next page144 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.5.1 Introduction to Spot Welding cabinetContinued
Weld power circuitThe electrical circuits of the Spot Welding cabinet consists of weld power circuitand control circuits to control the welding. The welding power for the welding gunis fed through a circuit breaker and inverter (for MFDC welding) and further out tothe welding power cable. The cabinet is prepared for power feeding from the flooror from top. The welding power cable (outgoing feeding) is connected, via cablegland, directly to terminals inside the Spot Welding cabinet.The circuit breaker has a built in thermal release that could be adjusted for customerspecific needs to protect welding equipment and to get selectivity in the powercircuit. The thermal release is set at 100 A at delivery. The maximum level shouldnot exceed 100 A.
Control CircuitsPower feeding 240/115 V AC and 24V DC for the control circuits is fed from therobot controller cabinet. Also, the safety circuits in the robot controller cabinet areused to interlock the welding timer.A welding timer (Bosch), integrated with the air cooled inverted, controls the weldingcurrent. The welding timer includes control program that gives possibility to programdifferent weld sequences. The programming is normally done on a programmingdevice or a PC that is connected directly to the welding timer. The interface betweenthe robot system and the welding timer is handled via a field bus interface (ProfiNet).Examples of signals are weld start, weld ready, weld programs choice and errorhandling.Also, cross connections, of interface signals and interlocking between the robotsystem (I/O-boards), the water and air unit, signals to DressPack or stationary gun,are done within the Spot Welding cabinet.Programming device for the welding timer is not included in the delivery.If the option 744-1 is chosen there will follow a door interlock with the SpotWeldingcabinet.
Note
For more information see:• Product manual for DressPack/SpotPack• Circuit diagrams• Separate manuals for the Bosch equipment
The welding capacity as well as the weld timer brand described below. Additionalfeatures could then be added to each of the cabinet variants.
Continues on next pageProduct specification - IRB 6700 1453HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.5.1 Introduction to Spot Welding cabinet
Continued
Option 782-13 Bosch MFDC ProfiNetThis option gives a basic Spot Welding cabinet equipped with a weld timer fromBosch with an integrated inverter with basic capacity.
General technical data
IECTechnical data
Bosch PSI 61C0.751OEMWeld timer and inverter
3x70 mm2Max wire range, incoming power
400-480 V ACPower feeding
110 A rms, 20 kA weld currentMax welding current
IP54Protection class
Specific technical data large cabinet
IECTechnical data
100 A (adjustable) 70-100 AMain breaker (ABB Sace XT1), thermalrelease
36 kAMain breaker, magnetic release
Continues on next page146 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.5.1 Introduction to Spot Welding cabinetContinued
Option 788-1 Forced air coolingOffers a cooling fan with housing placed on the rear of the Spot Welding cabinetwhich forces air on the cooling surface/grids of the thyristor or MFDC inverter (seepictures below). Cabling to the fan goes via a cable gland at the rear of the SpotWelding cabinet. The fan runs continuously when the welding system is poweredup.The fan is required to be used together with Bosch MFDC (option 782-13).
xx0900000746
Option 789-1 Earth fault protection unitOffers an earth fault protection integrated with the circuit breaker for the weldpower. If an earth fault occurs the circuit breaker is tripped.
Continues on next pageProduct specification - IRB 6700 1473HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.5.1 Introduction to Spot Welding cabinet
Continued
Option 790-1 Contactor for weld powerOffers a weld contactor with necessary wiring placed inside the Spot Weldingcabinet. The contactor is mounted after the inverter and opens up the weld circuitout from the cabinet. It is recommended to be used for increasing safety or whenusing tool change for weld guns. The contactor is open when the robot system isin motor off mode or when an specific I/O is set.
A
xx0900000747
DescriptionPos
Weld contactorA
Option 791-1 Weld power cable, 7 mOffers floor cable of 7 m length for weld power (3x35 mm2). One end of the weldpower cable is connected at terminal to the weld timer (Bosch) or the contactor(when option 790-1 is chosen). The cable enters the SpotWelding cabinet cia cablegland. The other end is equippedwith anMC connector TSB160/35 and is connectedat either the manipulator base (for robot gun Type S or Se) or to the stationary gun(for Type HSe).
Option 791-2 Weld power cable, 15 mOffers floor cable of 15 m length for weld power (3x35 mm²). See option 791-1 forfurther details.
Option 809-1 process cable to stationary gun, 7 mOffer floor cable of 7m length for process signals between the SpotWelding cabinetand the stationary gun. This option also includes internal cross connections betweenI/O, weld timer and power feeding etc.One end of the process cable enters the Spot Welding cabinet via cable gland andis connected at Phoenix terminals. The other end is equipped with a HD Harting 3modules and is connected to the stationary gun (for Type HSe).
Continues on next page148 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.5.1 Introduction to Spot Welding cabinetContinued
Option 809-2 process cable to stationary gun, 15 mOffer floor cable of 15 m length for process signals between the Spot Weldingcabinet and the stationary gun. See option 809-1 for further details.
Product specification - IRB 6700 1493HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.5.1 Introduction to Spot Welding cabinet
Continued
2.5.2 Interface description for spot welding cabinet
GeneralThe interface towards the Spot Welding cabinet is described in the tables below.
Connections for Spot Welding cabinet
Allowed capacitySpecificationPcsType
400-480 VAC,1Incoming power fromline i Max. 100 A rms, 50/60 Hz
Max. 150 A rms, 50/60 HzCable gland (min 24mm /max28 mm cable diameter)
1Outgoing power torobot
Max. 600 VAC,35 mm22Floor cable150 A rms at + 20°C (68°F)ambient temperature
Max. 600 VAC,35 mm21Floor cable protect-ive earth 150 A rms at + 20°C (68°F)
ambient temperaturei Incoming power connection made by customer. For incoming power and safety recommendations
see Product manual - DressPack/SpotPack IRB 6700.
Connections for Signals
Allowed capacitySpecificationPcsType
24 V DC, Max 0.5 A / outputModular Harting connector,type DD
1Water and air unit(on IRC5, option782-13)
24 V DC, Max 0.5 A / outputCable gland1Stationary gun (onIRC5, option 782-13)customer plate
See interface descriptionStationary gun type HSe
150 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.5.2 Interface description for spot welding cabinet
2.6 Water and air unit
2.6.1 Introduction
GeneralThe Water and Air unit contains components for water and air distribution andcontrol within the SpotPack. The water and air unit is controlled from the robotcontroller via the process software. Wiring is made via the Spot Welding cabinet.The capacity and functionality depends on the choice of different optioncombinations, see water and air unit options under this chapter.The unit is only used for the spot welding application
The water and air unitThe Water and Air unit has the following main features (see figure below):
• Adjustable, high speed water flow sensors.• Adjustable digital pressure switch for air.• Air filter with auto draining.• Possibility to balance water flow for complete package and for individual
circuits.• Preparation for additional options and preparation for easy exchange of
complete unit or separate circuits.• Equipped with extra (plugged) air outlets.
xx1700001596
The standard water and air unit consists of four main assemblies.• Water in circuit
Continues on next pageProduct specification - IRB 6700 1513HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.6.1 Introduction
• Water return circuit• Air supply circuit• Split box
Cables and hoses required for Water and Air unit are defined and described undereach option for water and air unit.
Water in circuitThe function of the water in circuit is to open / close the cooling water supply tothe Spot welding gun (see figure below). An air operated 2 port valve is used. Thevalve is controlled by a 3 port direct operated valve that is controlled by a digitalsignal from the robot control system. The circuit from left to right begins with aG1/2" thread used for the connection of the factory water supply system and endswith a male M22 x 1.5. (Suitable for a Swivel nut adapter DIN 20 078 A, werecommend a Parker 39C82-15-8BK fitting). From this point the water is led to thegun/robot base.
xx0900000749
Water return circuitThe water return circuit monitors the flow of the returning cooling water from theSpot welding gun (see figure below). The flow switch detects if the water flow istoo low in the cooling water circuit.The flow switch gives a digital signal to the robot control system, whichautomatically shuts off the electrical shut off valve in the water in circuit if the flowis too low.The system and the supply of cooling water are then automatically stopped tominimize risk of damage to the system.The water return circuit is delivered with a pre-set flow limit, set to 8 liters perminute at 0.2 MPa water pressure.The water return circuit begins from right with a Swivel Nut adapter (suitable for aSwivel nut adapter 20 078 A, we recommend a Swivel nut adapter 39C82-15-8BKfitting).
Continues on next page152 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.6.1 IntroductionContinued
It is also equipped with a flow control valve; the flow control can adjust the waterflow to the desired flow level. The flow rate can be monitored by the scale on theflow control valve. The scale can be rotated so that easy reading can be performed.This will serve as a rough function check in the flow range between 1 to 8 litresper minute.The flow control valve is when delivered adjusted for maximum flow.The circuit ends with a check-valve that will stop any reversing water flow and endswith an internal G ½" thread. From this point the water is led to the factory watersystem.
xx0900000750
A second water return, option 793-1, is also available with the same specificationas above.
Air supply circuitThe air supply circuit provides the function package with filtered air (see figurebelow).The air supply circuit begins with a internal G ½" thread, manually operated shutoff valve with residual pressure release though a silencer, air filter with nominalfiltration of 5 µm with a metal protection of the bowl, a digital pressure switch anda cross interface containing plugged air outlet ports (internal G 3/8" thread).There is a digital pressure switch to monitor the air pressure and to give a signalto the control system if the pressure becomes too low.The pressure switch is delivered with pre-set pressure limit. There is a lower limitset to 5 bar which means customer needs to provide at least 6 bar to overcomethe 1 bar pressure drop over the air preparation unit.
Continues on next pageProduct specification - IRB 6700 1533HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.6.1 Introduction
Continued
The air supply circuit ends with a Swivel Nut adapter (suitable for a Swivel Nutadapter 20 078 A, we recommend a Parker 39C82-15-8BK fitting).
xx0900000751
Continues on next page154 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.6.1 IntroductionContinued
Split box/Connection boxWith the split box, the 24VDC supply and signals are connected and distributed tothe different units on the water and air unit, see figure below. The design makesdisconnection of separate items for service and repair on the water and air unitvery easy. The split box has a protection class IP67, whichmeans it is well protectedagainst dust and water leakage.
xx0900000752
Continues on next pageProduct specification - IRB 6700 1553HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.6.1 Introduction
Continued
MountingType S, robot mounted spot welding gun, is mounted at the robot at factory andwater and air hoses are included and connected to the robot base.
xx0900000754
Type HS, robot handles part against a pedestal mounted spot welding gun, theWater and Air panel is delivered in a box together with the robot.
Signals for water and air unitElectrical connections to robot I/O board are made via the Split box on the Waterand Air unit or to connection box at robot base (the figure below shows Split box,for connection box see the circuit diagram).8 x M12 connections (4 pins) are available. The number in use depends on optionchoices. But at least two are free connection and can be used for customerpurposes.The Split box has six connections prepared for the following units:
• 1. Electric water shut off valve• 2. Pressure switch• 3. Flow switch 1• 4. Flow switch 2 (Option 793-1 Second Water Return)• 5. Proportional valve: Prop. ref. signal & pressure OK signal• 6. Proportional valve: Power supply
Continues on next page156 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.6.1 IntroductionContinued
The cable and cable length between the Split box and the Spot Welding cabinetmust be specified (see option 797-1,-2,-3,-4). See the circuit diagram.
DescriptionTypeOption
The basic water and air unit for type S is equippedfor a robot handled gun and with the following com-ponents:
Water and Air unit, type S792-1
Water in circuitWater return circuitAir supply circuitSplit box1/2 " hose between air supply circuit andmanipulatorbase (PROC 1) i1/2 " hose between water in circuit and manipulatorbase (PROC 2) i1/2 " hose between water return circuit and manipu-lator base (PROC 3) i
The basic water and air unit for type HS is equippedfor a pedestal/stationary gun.
Water and Air unit, type HS792-2
Hoses between water and air unit, welding equip-ment and robot are not supplied. These have to bearranged by the customer. i
The option adds an additional water return circuit.Second water return793-1See Water return circuit.An additonal 1/2” water hose (PROC 4) from theWater and Air unit to manipulator base is included.
Offers floor cable of 7 m length for signals to thesplit box placed on the water and air unit. This cableis connected to the cabinet with a modular Hartingand it ends with a quick connector at the split box.
Cable to split box, 7 m797-1
Offers floor cable of 15 m length for the split box.See description of option 797-1.
Cable to split box, 15 m797-2
Offers floor cable of 22 m length for the split box.See description of option 797-1.
Cable to split box, 22 m797-3
Offers floor cable of 30 m length for the split box.See description of option 797-1.
Cable to split box, 30 m797-4
i For IRB 6700Inv hoses and adapter are not supplied. These have to bearranged by the customer.
Product specification - IRB 6700 1573HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.6.1 Introduction
Continued
2.6.2 Technical data
Media interface descriptionThe interface towards the Water and Air unit is described in table below.
SpecificationPcsType
G 1/2” thread i1Incoming water
G 1/2” thread (M22 x 1.5) i1Outgoing water
G 1/2” thread i1Incoming air
G 3/8” thread ii1Extra air outleti Connection to be made by customer.ii Plugged at delivery (to be used for tip-dresser or other equipment).
General data
DescriptionWater
Max. 0.6 MPa / 87PSIOperating pressure
1.2 MPa / 174 PSIProof pressure
< 0.2 MPa at 8 litre/minute iMaximum pressure drop
1 - 16 l/minFlow regulating (each circuit)
140-170 mesh, 100 μmWater qualityi The pressure drop is measured under the following conditions:
• Measuring point 1: Incoming water connection at water and air unit.• Measuring point 2: Outgoing water connection at water and air unit.
The water hoses (Proc 2 and Proc 3) are cross-connected at the end at axis 6 (thepressure drop is measured without any tool).
DescriptionAir
Max. 1.0 MPa / 145 PSIOperating pressure
Approximately 4000 litres/min. (at 0.7 MPa with a 0.1MPa pressure drop
Flow capacity
0.100 - 1.000 MPaPressure switch set range
Use clean air.Air qualityWhen there is excessive condensate, install a devicethat eliminates water such as dryer or water separator(Drain Catch) on the inlet side of the air filter.
158 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.6.2 Technical data
2.7 Connection kits
GeneralFor detailed information on connection location see Interface descriptions forDressPack on page 109Below is an example of how a connector kit and its parts can look like.
xx1300000223
Continues on next pageProduct specification - IRB 6700 1593HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.7 Connection kits
2.7.1 Base - Connector kits
Available options
DescriptionResolver conn., axis 7DressPack options
864-1798-3NameOption
XCP/CS, Proc 1 on base459-1
XFB 7453-1
Note
Ethernet and Servo power connection kits not available.
Option 459-1, CP/CS, Proc 1 on baseR1. CP/CS and Proc 1 on base for option 798-3.This option offers a kit with connectors. This must be assembled by the customer.The kit contains:
• 1 Hose fittings (Swivel nut adapter, (½”, M22x1,5 Brass, 24 degree seal))• Connector with:
HAN EMC / M 401 pcs Hood Foundry (Harting)
Shell size 161 pcs Hinged frame (Harting)
Type HD (25 pin)2 pcs Multicontact, female (Harting)
Type DD (12 pin)1 pcs Multicontact, female (Harting)
Type EE (8 pin)1 pcs Multicontact, female (Harting)
For 1,5 mm210 pcs Female crimp contacts
For 0,5 mm210 pcs Female crimp contacts
For 1,0 mm210 pcs Female crimp contacts
For 2,5 mm210 pcs Female crimp contacts
For 0,14– 0,37 mm212 pcs Female crimp contacts
For 0,2– 0,56 mm245 sockets
Assembly Accessories to complete connector
Assembly instruction
Continues on next page160 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.7.1 Base - Connector kits
Option 453-1, FB 7R3. FB 7 on base for option 864-1This option offers a kit with a connector. This must be assembled by the customer.The kit contains:
• Connector with:
UTOW1 pcs Multiple connector (pin)
8 pin1 pcs Adaptor
for 0,13-0,25 mm28 pcs Pin
Assembly Accessories to complete connector
Assembly instruction
Product specification - IRB 6700 1613HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.7.1 Base - Connector kits
Continued
2.7.2 Axis 3 - Connector kits
Available options
DescriptionDressPack options
798-3NameOption
UTOWXCP/CS,CBUS/SP/SSProc 1 axis 3
458-1
Option 458-1, CP/CS/CBus/SP/SS, Proc 1 axis 3CP/CS/CBus/SP/SS, Proc 1 axis 3 on tool side for option 780-3 and 780-4.This kit offers a kit with connectors to be mounted at toolside of axis 3.This must be assembled by the customer.The kit contains:
• 1 Hose fitting (Parker Push lock (1/2”, M22x1,5 Brass, 24 degree seal))• Connector with:
CP/CS
UTOW71626PH05, Shell size 161 pcs UTOW Pin connector 26p, bulkhead
RM18W3K, 0.21-0.93 mm226 pcs Pin
CBUS
UTOW71210PH05 Shell size 121 pcs UTOW Pin connector 10p, bulkhead
RM18W3K, 0.21-0.93 mm210 pcs Pin
Ethernet
Harting 2103 881 pcs Socket connector M12
Harting 61 03 0, 0.13-0.33 mm24 pcs Socket
SP (Servo Power)
1 pcs Bulkhead contact M23
AWG 24-174 pcs Crimp pin 1 mm
AWG 18-144 pcs Crimp pin 2 mm
SS (Servo Signal)
1 pcs Bulkhead contact M23
AWG 28-2017 pcs Pin
Assembly Accessories to complete connector
Assembly instruction
162 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.7.2 Axis 3 - Connector kits
2.7.3 Axis 6 - Connector kits
Available options
Description
780-4(LeanID)
780-3(MH 3)
NameOption
UTOWXXCP/CS/CBUS/SP/SS Proc 1 axis 6543-1
MC, Seperateconductors
XWeld Proc 1-4 axis 6452-1
Option 543-1, CP/CS/CBus/SP/SS, Proc 1 axis 6CP/CS/CBus/SP/SS, Proc 1 axis 6 on tool side for option 780-3 and 780-4.This kit offers a kit with connectors to be mounted at toolside of axis 6.This must be assembled by the customer.The kit contains:
• 1 Hose fitting (Swivel nut adapter (1/2”, M22x1,5 Brass, 24 degree seal))• Connector with:
CP/CS
UTOW71626PH05, Shell size 161 pcs UTOW Pin connector 26p, bulkhead
RM81W3K, 0.21-0.93 mm226 pcs Pin
CBUS
UTOW71210PH05 Shell size 121 pcs UTOW Pin connector 10p, bulkhead
RM18W3K, 0.21-0.93 mm210 pcs Pin
Ethernet
Harting 2103 881 pcs Socket connector M12
Harting 61 03 0, 0.13-0.33 mm24 pcs Socket
SP (Servo Power)
1 pcs Bulkhead contact M23
AWG 24-174 pcs Crimp pin 1 mm
AWG 18-144 pcs Crimp pin 2 mm
SS (Servo Signal)
1 pcs Bulkhead contact M23
AWG 28-2017 pcs Pin
Assembly Accessories to complete connector
Assembly instruction
Continues on next pageProduct specification - IRB 6700 1633HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.7.3 Axis 6 - Connector kits
Option 452-1, Weld, Proc 1-4 axis 6Weld and Proc 1-4 axis 6 on manipulator side for option 780-4The process cable package from axis 6 ends with free end for media and for weldpower cable. The option 452-1 offers a kit for connectors. This must be assembledby the customer when hoses and power cable has been cut to required length.The kit contains:
• 4 Hose fittings (Swivel Nut adapter, (2 x ½”, M22x1,5) and (2x 3/8", M16x1.5))• 1 Multi contact connector (Female) type including:• 1 pc Welding connector 3x25 mm2
Diameter 24-28 mm1 pc Cable gland
0,21-0,93 mm21 pc End housing
PG36/PG291 pcs Reducing coupling
Assembly Accessories to complete connector
Assembly instruction
164 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
2 DressPack and SpotPack2.7.3 Axis 6 - Connector kitsContinued
3 Specification of variants and options3.1 Introduction to variants and options
GeneralThe different variants and options for the IRB 6700 are described in the followingsections. The same option numbers are used here as in the specification form.
Related informationFor the controller see Product specification - Controller IRC5.For the software options see Product specification - Controller software IRC5.
Product specification - IRB 6700 1653HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.1 Introduction to variants and options
3.2 Manipulator
Variants
Reach (m)Handling capacity (kg)IRB TypeOption
2.652356700435-111
2.802056700435-112
3.051756700435-113
3.201506700435-114
2.602006700435-115
2.851556700435-116
2.703006700435-126
3.002456700435-127
2.603006700Inv435-138
2.902456700Inv435-139
Manipulator color
NoteDescriptionOption
ABB Orange standard209-1
ABB White standard209-2
Standard colorABB Graphite White standard209-202
Colors according to RAL-codes209-4 --192
Note
Notice that delivery time for painted spare parts will increase for none standardcolors.
Protection types
NoteProtection typeOption
IP67Standard287-4
See Protection type Foundry Plus 2 on page 9 for a com-plete description of protection type Foundry Plus 2.
Foundry Plus 2287-3
Warranty
DescriptionTypeOption
Standard warranty is 12months fromCustomer DeliveryDate or latest 18 months after Factory Shipment Date,whichever occurs first. Warranty terms and conditionsapply.
Standard warranty438-1
Standard warranty extended with 12 months from enddate of the standard warranty. Warranty terms and con-ditions apply. Contact Customer Service in case of otherrequirements.
Standard warranty + 12months
438-2
Continues on next page166 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.2 Manipulator
DescriptionTypeOption
Standard warranty extended with 18 months from enddate of the standard warranty. Warranty terms and con-ditions apply. Contact Customer Service in case of otherrequirements.
Standard warranty + 18months
438-4
Standard warranty extended with 24 months from enddate of the standard warranty. Warranty terms and con-ditions apply. Contact Customer Service in case of otherrequirements.
Standard warranty + 24months
438-5
Standard warranty extended with 6 months from enddate of the standard warranty. Warranty terms and con-ditions apply.
Standard warranty + 6months
438-6
Standard warranty extended with 30 months from enddate of the standard warranty. Warranty terms and con-ditions apply.
Standard warranty + 30months
438-7
Maximum 6 months postponed start of standard war-ranty, starting from factory shipment date. Note that noclaims will be accepted for warranties that occurred be-fore the end of stock warranty. Standard warranty com-mences automatically after 6 months from FactoryShipment Date or from activation date of standard war-ranty in WebConfig.
Note
Special conditions are applicable, seeRoboticsWarrantyDirectives.
Stock warranty438-8
Warranty for DressPack
Note
Option 780-3 upper arm DressPack HM3 is not covered by warranty.
Note
Option 780-4 DressPack LeanID is covered by the warranty.
Product specification - IRB 6700 1673HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.2 Manipulator
Continued
3.3 Equipment
General
DescriptionTypeOption
A safety lamp with an orange fixed light can be mountedon the manipulator. The lamp is active in MOTORS ONmode. The safety lamp is required on a UL/UR approvedrobot.
Safety lamp213-1
Lifting device on the IRB 6700 floor standing manipulatorfor fork-lift handling.
Fork lift device IRB6700 i
159-1
Note. When Cooling Fan for axis 1 motor unit is used, thismust be disassembled in order to use fork lift device.
For IRB 6700Inv hoses and adapter are not supplied. Thesehave to be arranged by the customer.
Fork lift device IRB6700Inv i
159-2
Can also be used for IRB 7600. See Installation on page20,for dimension drawing. ii
Base plate37-1
For in use recommendations see Cooling fan for axis 1motor on page 94.
Cooling fan for axis1 motor (IP54)
87-1
Not for protection Foundry Plus. Not together with trackmotion.
See Figure in Upper arm cover on page 169.Upper arm covers430-1Included in protection Foundry.
For a more accurate marking of the synchronization posi-tion of the robot. Assembly instructions are included.
Labels for synchron-ization markings
804-1
See Figure for Synchronize labels, Axis 1 - 6.i Its recommended to remove the fork lift devices after useii Can not be used for IRB 6700Inv.
Synchronization labelsThe option contains labels for each axis. Below is an example of the synchronizationlabels.
xx1300001127
Continues on next page168 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.3 Equipment
Upper arm cover
(A)
xx1400002039
DescriptionPos
Option 430-1A
Electronic Position Switches (EPS)The mechanical position switches indicating the position of the three main axesare replaced with electronic position switches for up to 7 axes, for increasedflexibility and robustness. For more detailed information, see Productspecification - Controller IRC5with FlexPendant andApplicationmanual - ElectronicPosition Switches.
Resolver connection, axis 7
NoteDescriptionOption
Used together with first additional drive, option 907-1.On base864-1
Foundry Plus Cable GuardThe manipulator cables are equipped with an additional protection of aluminizedleather against e.g. aluminium spits and flashes and chips frommachining. Processcable for material handling from base to axis 3, option 798-3 has the sameprotection.
DescriptionTypeOption
For extra protection of cables.Foundry Plus CableGuard
908-1Requires option 287-3 Foundry Plus.
Continues on next pageProduct specification - IRB 6700 1693HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.3 Equipment
Continued
Working range limitationTo increase the safety of the robot, the working range of axis 1 can be restrictedby extra mechanical stops.
DescriptionTypeOption
Two stops which allow the working range to be restrictedin increments of 15o .
Axis 1, 15 degrees29-1
(A)(B)
xx1400002035
DescriptionPos
Two mechanical stopsA
Bolt tightening torque: 60 NmB
Extended working range
DescriptionTypeOption
To extend the working range on axis 1 from ± 170°to ±220°.
Extended workrange axis 1
561-1
When the option is used the mechanical stop shall be dis-assembled.EPS (Electronic Position Switches) functionality (option810-1 or -2) is required. i
i This option is not available for IRB 6700Inv.
Standard calibration method
DescriptionTypeOption
Preferred standard calibration method. Robust, highperformance axis calibration using only mechanicalcalibration stops and software.
Axis calibration1999-1
Continues on next page170 Product specification - IRB 6700
3HAC044265-001 Revision: K© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.3 EquipmentContinued
DescriptionTypeOption
Previous standard calibrationmethod only to be usedin special cases if customers would like to harmonizecalibration with already installed base. i
Calibration Pendulum1999-2
i This option is not available for IRB 6700Inv
Note
The calibration methods are not interchangeable.
Product specification - IRB 6700 1713HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.3 Equipment
Continued
3.4 Floor cables
GeneralAdditional floor cables for SpotPack options, seeSpotPack Floor Cables on page178.
Manipulator cable length
LengthsOption
7 m210-2
15 m210-3
22 m210-4
30 m210-5
172 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.4 Floor cables
3.5 Process DressPack
Connection to
DescriptionConnection toOption
The signals CP/CS are connected to 12-pole screw terminals,Phoenix MSTB 2.5/12-ST-5.08, in the controller. The cablebetween R1.CP/CS and the controller is supplied. For inform-ation about the limited number of signals available, see TypeH/HSe on page 115, and Type Se on page 128.
Cabinet16-1
Communication
DescriptionTypeOption
Includes customer power CP, customer signals CS.Parallel commu-nication
455-1
Includes CP, customer signals and CAN/DeviceNet or Profibusfor process cable package.
Parallel and buscommunication
455-4
Includes CP, customer signals and PROFINET or Ethernet/IPfor process cable package
Parallel andEther-net communica-tion
455-8
Product specification - IRB 6700 1733HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.5 Process DressPack
3.6 DressPack floor cables
Connection to Parallel/CAN DeviceNet/Profibus/EthernetFollowing information specifies the cable length for Parallel,CANDeviceNet/Profibus/Ethernet for connection to cabinet.
DescriptionLengthsOption
7 m90-2/92-2
15 m90-3/92-3
22 m90-4/92-4
30 m90-5/92-5
174 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.6 DressPack floor cables
3.7 DressPack Lower and Upper arm
DressPack process configuration
Note
For more information about the process cable packages, see DressPack onpage 107
NoteDescriptionOption
Includes signals and one air hose.Material Handling778-1
Includes signals, weld power cable, one air hose andthree media hoses.
Spot Welding778-2
DressPack lower arm
NoteDescriptionOption
Material Handling / Spot WeldingRouting from base toaxis 3
798-3
DressPack upper arm
NoteDescriptionOption
Requires option 778-1 and option 798-3 i .External routing fromaxis 3 to axis 6
780-3
Requires option 798-3. iInternal routing fromaxis 3 to axis 6
780-4
i Upper arm cabling is not available for IRB 6700Inv together with option Foundry plus 2.
Note
If option 780-4, LeanID, is selected the payload will decrease, for detailedinformation see Load diagrams on page 32
Product specification - IRB 6700 1753HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.7 DressPack Lower and Upper arm
3.8 Connection kits
GeneralThe connectors fit to the connectors at the manipulator base, axis 3 and 6respectively.
ContentThe kit consists of connectors, pins and sockets. For technical description, seeConnection kits on page 159.
DescriptionTypeOption
For the Customer Power/Customer Signal connectorand one Process connector on themanipulator base.Sockets for bus communication are included.
R1.CP/CS, PROC1459-1
For the 7-axis connector on the manipulator base.R3.FB7453-1
For the Customer Power/Customer Signal connectorand one Process connector at axis 3. Pins for buscommunication are included.
R2.CP/CS, PROC1458-1
Weld connector and four Process connectors at axis6, the manipulator side.
Weld, PROC1-4 axis 6452-1
Connector for customer power/customer signal/cus-tomer bus at axis 6 tool side.
CP/CS/BUS, PROC1 axis 6543-1
176 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.8 Connection kits
3.9 Servo Gun
ContentFor technical description see Servo gun on page 95.
LengthsOption
For robot handled Servo Gun.785-1
For Stationary Servo Gun.785-2
Connection to first driveFollowing information specifies the cable length for Connection to first drive. Forfurther information see Servo gun on page 95.
LengthsOption
7 m786-1
15 m786-2
22 m786-3
30 m786-4
Product specification - IRB 6700 1773HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.9 Servo Gun
3.10 SpotPack Floor Cables
Weld Power CableFollowing information specifies the cable length for the Weld Power cable, fromthe Spot Welding process cabinet to the manipulator base.
DescriptionLengthsOption
7 m791-1
15 m791-2
Process Cable to Stationary GunFollowing information specifies the cable length for the Process Cable to theStationary Gun, from the Spot Welding process cabinet to the Stationary Gun.
LengthsOption
7 m809-1
15 m809-2
Cable to Split BoxFollowing information specifies the cable length for the cable to Split Box, fromthe Spot Welding process cabinet to the Split box on the manipulator base.
LengthsOption
7 m797-1
15 m797-2
22 m797-3
30 m797-4
178 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.10 SpotPack Floor Cables
3.11 Process cabinet
Empty cabinet
DescriptionTypeOption
See Product specification - ControllerIRC5 with FlexPendant
Empty cabinet small768-1
See Product specification - ControllerIRC5 with FlexPendant
Empty cabinet large768-2
See Product specification - ControllerIRC5 with FlexPendant
Installation kit715-1
Product specification - IRB 6700 1793HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.11 Process cabinet
3.12 Water and air
Water and air unit
DescriptionTypeOption
DressPack floorType S792-1
DressPack floorType HS/HSe792-2
Second water return
DescriptionTypeOption
DressPack floorSecond water return793-1
180 Product specification - IRB 67003HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.12 Water and air
3.13 User documentation
User documentationThe user documentation describes the robot in detail, including service and safetyinstructions.All documents can be found via myABB Business Portal, www.myportal.abb.com.
Product specification - IRB 6700 1813HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
3 Specification of variants and options3.13 User documentation
This page is intentionally left blank
4 Accessories4.1 Introduction to accessories
GeneralThere is a range of tools and equipment available, especially designed for themanipulator.
Basic software and software options for robot and PCFor more information, see Product specification - Controller IRC5 with FlexPendantand Product specification - Controller software IRC5.
Robot peripherals• Track Motion• Motor Units
Product specification - IRB 6700 1833HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
4 Accessories4.1 Introduction to accessories
This page is intentionally left blank
IndexAaccessories, 183
CCalibration Pendulum, 29category 0 stop, 93category 1 stop, 93
Ddocumentation, 181DressPack warranty, 167
EElectronic Position Switches, 169EPS, 169equipment, on robot, 67
Ffine calibration, 29fitting equipment to robot, 67
Hholes for equipment, 67
Iinstructions, 181
Mmanuals, 181
Ooptions, 165
Pproduct standards, 18
Ssafety standards, 18service instructions, 181standards, 18
ANSI, 19CAN, 19EN, 18EN IEC, 18EN ISO, 18
standard warranty, 166stock warranty, 166stopping distances, 93stopping times, 93
Uuser documentation, 181
Vvariants, 165
Wwarranty, 166warranty for DressPack, 167
Product specification - IRB 6700 1853HAC044265-001 Revision: K
© Copyright 2018 ABB. All rights reserved.
Index
ABB AB, RoboticsRobotics and MotionS-721 68 VÄSTERÅS, SwedenTelephone +46 (0) 21 344 400
ABB AS, RoboticsRobotics and MotionNordlysvegen 7, N-4340 BRYNE, NorwayBox 265, N-4349 BRYNE, NorwayTelephone: +47 22 87 2000
ABB Engineering (Shanghai) Ltd.Robotics and MotionNo. 4528 Kangxin HighwayPuDong DistrictSHANGHAI 201319, ChinaTelephone: +86 21 6105 6666
ABB Inc.Robotics and Motion1250 Brown RoadAuburn Hills, MI 48326USATelephone: +1 248 391 9000
abb.com/robotics
3HAC044
265-001,Rev
K,en
© Copyright 2018 ABB. All rights reserved.