RNC Product Description
-
Upload
vladimir-vozian -
Category
Documents
-
view
813 -
download
15
Transcript of RNC Product Description
Product Description
RNC V200R010
Issue 02
Date 2008-03-30
HUAWEI TECHNOLOGIES CO., LTD.
Issue 02 (2008-03-30) Commercial in Confidence Page 2 of 65
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. Please feel free to contact our local office or company headquarters.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Email: [email protected]
Copyright © Huawei Technologies Co., Ltd. 2008. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.
Issue 02 (2008-03-30) Commercial in Confidence Page 3 of 65
About This Document
Author Prepared by Zhang Lijun Date 2007-06-30
Reviewed by Chang Rong, Dai Hongfeng, Dong Qing, Hu Guang, Lian Haichun, Qian Chunxia, Tong Aruna, Wu Yuqiong, Yang Yongpeng, Yu Huichun, and Zhu Lingyan
Date 2007-07-15
Approved by Date
Summary This document provides information for Huawei WCDMA Radio Network Controller (RNC).
This document includes:
Chapter Details
1 Introduction to the RNC Describes the position of the RNC in the WCDMA network.
2 Key Benefits Describes the key benefits of the RNC.
3 System Architecture Describes the hardware structure, logical structure, and hardware configuration of the RNC.
4 Operation and Maintenance Describes the OM structure and OM functions of the RNC.
5 Reliability Describes the system reliability, hardware reliability, and software reliability of the RNC.
6 Technical Specifications Describes the technical specifications for the RNC.
7 Installation Describes the hardware and software installation requirements for the RNC.
Issue 02 (2008-03-30) Commercial in Confidence Page 4 of 65
History Issue Details Date Author Approved by
01 This is the initial commercial release.
2007-07-15 Zhang Lijun
02 This is the second commercial release. � The model N68-22 of
RNC cabinets is changed to N68E-22.
� The descriptions about CSU are deleted.
2008-03-30 Zhang Lijun
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 5 of 65
Contents
1 Introduction to the RNC .......................... .......................................................................8
1.1 About This Chapter........................................................................................................................... 8
1.2 Position of the RNC in the WCDMA Network................................................................................... 8
1.3 Main Functions of the RNC .............................................................................................................. 9
2 Key Benefits ..................................... .............................................................................10
2.1 About This Chapter......................................................................................................................... 10
2.2 All-IP Platform of Advanced Radio Controller................................................................................. 10
2.3 High Integration and Large Capacity.............................................................................................. 10
2.4 Flexible Configurations Adapting to Traffic Models .........................................................................11
2.5 Resource Sharing Between Control Plane and User Plane ...........................................................11
2.6 Multiple Clock Sources....................................................................................................................11
2.7 Diverse Transmission Solutions ..................................................................................................... 12
2.7.1 Multiple Iub Network Topologies............................................................................................ 12
2.7.2 Multiple Types of Transmission Port...................................................................................... 12
2.7.3 High Reliability of Transmission ............................................................................................ 13
2.7.4 Flexible Configuration of Interface Boards ............................................................................ 13
2.7.5 IP Transport on the Iub/Iur/Iu Interfaces................................................................................ 13
2.7.6 Hybrid IP Transport on the Iub Interface ............................................................................... 13
2.7.7 ATM/IP Dual Stack on the Iub Interface................................................................................. 13
2.7.8 Satellite Transmission on the Iub Interface ........................................................................... 13
2.7.9 Efficient Transmission on the Iub Interface ........................................................................... 14
2.7.10 Dynamic Management of the Bandwidth............................................................................. 14
2.7.11 Inverse Multiplexing on ATM................................................................................................ 14
2.7.12 Fractional Functions ............................................................................................................ 14
2.7.13 Timeslot Cross Connection ................................................................................................. 15
2.7.14 Multilink PPP ....................................................................................................................... 15
2.8 Advanced RRM Algorithms ............................................................................................................ 15
2.8.1 Power Control........................................................................................................................ 15
2.8.2 Handover ............................................................................................................................... 15
2.8.3 Radio Resource Allocation .................................................................................................... 15
2.8.4 CAC and Load Control .......................................................................................................... 16
2.8.5 Service Differentiation Based on Subscriber Priorities.......................................................... 16
2.9 Advanced Solutions to Radio Data Services.................................................................................. 16
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 6 of 65
2.9.1 HSDPA................................................................................................................................... 16
2.9.2 HSUPA................................................................................................................................... 16
2.9.3 MBMS.................................................................................................................................... 17
2.10 High Compatibility of Protocols .................................................................................................... 17
3 System Architecture .............................. .......................................................................18
3.1 About This Chapter......................................................................................................................... 18
3.2 Physical Structure .......................................................................................................................... 18
3.2.1 Cabinet Appearance .............................................................................................................. 18
3.2.2 Cabinet Components............................................................................................................. 19
3.2.3 Subrack Components ............................................................................................................ 21
3.2.4 RSS Subrack ......................................................................................................................... 22
3.2.5 RBS Subrack ......................................................................................................................... 25
3.3 Logical Structure............................................................................................................................. 26
3.3.1 Internal Switching Module ..................................................................................................... 26
3.3.2 User Plane Data Processing Module .................................................................................... 26
3.3.3 Control Plane Data Processing Module ................................................................................ 27
3.3.4 Clock Module......................................................................................................................... 27
3.3.5 Transmission Interface Module ............................................................................................. 27
3.3.6 OM Module ............................................................................................................................ 27
3.4 Hardware Configuration ................................................................................................................. 28
3.4.1 Minimum Configuration.......................................................................................................... 28
3.4.2 Maximum Configuration......................................................................................................... 28
3.4.3 Typical Configurations ........................................................................................................... 29
3.4.4 Hardware Expansion Schemes ............................................................................................. 30
4 Operation and Maintenance........................ .................................................................31
4.1 About This Chapter......................................................................................................................... 31
4.2 OM Structure .................................................................................................................................. 31
4.3 OM Functions ................................................................................................................................. 32
4.3.1 Security Management............................................................................................................ 33
4.3.2 Configuration Management ................................................................................................... 33
4.3.3 Maintenance Management .................................................................................................... 35
4.3.4 Fault Detection ...................................................................................................................... 37
4.3.5 Performance Management .................................................................................................... 38
4.3.6 Alarm Management ............................................................................................................... 38
4.3.7 Loading Management............................................................................................................ 39
4.3.8 Status Monitoring................................................................................................................... 39
4.3.9 Message Tracing ................................................................................................................... 40
4.3.10 Log Management................................................................................................................. 41
4.3.11 Software Management......................................................................................................... 41
5 Reliability...................................... .................................................................................43
5.1 About This Chapter......................................................................................................................... 43
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 7 of 65
5.2 System Reliability ........................................................................................................................... 43
5.3 Hardware Reliability ....................................................................................................................... 44
5.4 Software Reliability......................................................................................................................... 45
6 Technical Specifications ......................... .....................................................................47
6.1 About This Chapter......................................................................................................................... 47
6.2 Performance Specifications............................................................................................................ 47
6.3 Transmission Port Specifications ................................................................................................... 48
6.4 GPS Feeder Specifications ............................................................................................................ 49
6.5 Reliability Specifications................................................................................................................. 49
6.6 Structural Specifications ................................................................................................................. 49
6.7 Electrical Specifications.................................................................................................................. 50
6.8 Power Consumption in Typical Configurations .............................................................................. 50
6.9 Clock Precision Specifications ....................................................................................................... 51
6.10 Noise and Safety Compliance...................................................................................................... 51
6.11 Environmental Protection Specifications ...................................................................................... 52
6.12 International Protection Specifications ......................................................................................... 52
6.13 Environmental Requirements....................................................................................................... 52
6.13.1 Storage Environment ........................................................................................................... 52
6.13.2 Transportation Environment ................................................................................................ 55
6.13.3 Working Environment .......................................................................................................... 57
7 Installation ..................................... ................................................................................60
7.1 About This Chapter......................................................................................................................... 60
7.2 Hardware Installation...................................................................................................................... 60
7.3 Software Installation ....................................................................................................................... 61
A Acronyms and Abbreviations ...................... .............................................................62
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 8 of 65
1 Introduction to the RNC
1.1 About This Chapter This chapter consists of the following sections:
� Position of the RNC in the WCDMA Network � Main Functions of the RNC
1.2 Position of the RNC in the WCDMA Network The RNC is an important element of the WCDMA network. RNCs and NodeBs compose the UMTS Terrestrial Radio Access Network (UTRAN).
Figure 1-1 shows the position of the RNC in the WCDMA network.
Figure 1-1 Position of the RNC in the WCDMA network
UTRANUu
UEIu
CN
Iu-CS
MSC server
MGW
Iub
NodeB
NodeB
Iub
NodeB RNC
RNC
Iu-PS
Iu-BC
CBC
SGSN
Iur
Iub
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 9 of 65
CN: Core Network CBC: Cell Broadcast Center MGW: Media Gateway MSC server: Mobile Switching Center server RNC: Radio Network Controller SGSN: Serving GPRS Support Node UE: User Equipment UTRAN: UMTS Terrestrial Radio Access Network
As shown in Figure 1-1, each RNC can be connected to:
� NodeBs through the lub interface � The MSC (or the MSC server and MGW in R4/R5/R6), which processes Circuit
Switched (CS) services through the Iu-CS interface � The SGSN, which processes Packet Switched (PS) services through the Iu-PS
interface � The CBC, which processes broadcast services through the Iu-BC interface � Another RNC through the Iur interface
1.3 Main Functions of the RNC The RNC has the following main functions:
� Broadcasting system information and controlling UE access � Performing mobility management, such as handover and Serving Radio Network
Subsystem (SRNS) relocation � Performing radio resource management, such as Macro Diversity Combining
(MDC), power control, and cell resource allocation � Providing radio bearer services for both CS and PS domains � Providing transport channels between the CN and UEs � Ciphering and deciphering the signaling and data on radio channels
The model of Huawei RNC is BSC6810. Throughout the rest of this document, Huawei RNC is referred to as BSC6810. All its interfaces, including the Iub, Iur, Iu-CS, Iu-PS, and Iu-BC are standard interfaces, which enable the BSC6810 to connect to the NodeB, RNC, MSC, SGSN, and CBC of other vendors.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 10 of 65
2 Key Benefits
2.1 About This Chapter The design of the BSC6810 takes into consideration the factors such as services, capacity, transmission, and Operation and Maintenance (OM).
The BSC6810 brings the following benefits:
� All-IP Platform of Advanced Radio Controller � High Integration and Large Capacity � Flexible Configurations Adapting to Traffic Models � Resource Sharing Between Control Plane and User Plane � Multiple Clock Sources � Diverse Transmission SolutionsDiverse Transmission Solutions � Advanced RRM AlgorithmsAdvanced RRM Algorithms � Advanced Solutions to Radio Data ServicesAdvanced Solutions to Radio Data
Services � High Compatibility of Protocols
2.2 All-IP Platform of Advanced Radio Controller The BSC6810 uses the all-IP Platform of Advanced Radio Controller (PARC) developed by Huawei. PARC unifies the switching system of Asynchronous Transfer Mode (ATM), Time Division Multiplexing (TDM), and IP. Thus, it can serve as a uniform platform of GSM, CDMA, and WCDMA controllers. This platform can meet the requirements for the development of high-speed packet services and fully protect your network investment.
2.3 High Integration and Large Capacity The BSC6810 has the following features:
� The BSC6810 is highly integrated. Based on the Gigabit Ethernet (GE) star non-blocking switching on the Medium Access Control (MAC) sublayer, the BSC6810 achieves a central switching capacity of 120 Gbit/s.
� The BSC6810 supports up to 1,700 NodeBs and 5,100 cells.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 11 of 65
� The BSC6810 supports up to 51,000 Erlang voice traffic or a total of 3,264 Mbit/s PS throughput in the uplink (UL) plus downlink (DL). Such capacity, however, is implemented by only two cabinets.
� The BSC6810 provides a single-cabinet solution that supports 24,000 Erlang voice traffic or 1,536 Mbit/s (UL + DL) PS throughput.
2.4 Flexible Configurations Adapting to Traffic Mod els The number of signaling processing boards and that of data processing boards are flexible so that the quantity of resources on the user plane and control plane can meet the requirements of traffic models.
In the case that a single set ratio of board configuration is inconsistent with the actual traffic model, the flexible configurations of boards in the BSC6810 help prevent wasting resources. The waste of control plane resources may attribute to the bottleneck at user plane resources, and the other way round.
2.5 Resource Sharing Between Control Plane and User Plane
In BSC6810, an SPUa board has four independent subsystems. Each subrack has a subsystem working as the Main Processing Unit (MPU) subsystem for the management of resources on the user plane and resource allocation during a call. The other subsystems work as Signaling Process Unit (SPU) subsystems, which process signaling messages on the Iu, Iur, Iub, and Uu interfaces to implement the signaling processing function.
The SPU subsystems, working as the processor for control plane data, form a control plane resource pool; the DSPs, working as the processor for user plane data, form a user plane resource pool.
The resources of control plane and user plane within a subrack are managed and allocated by the MPU subsystem. When a new call travels to the subrack, the MPU subsystem forwards the resources request to other subracks in case of overload. If any subrack has enough resources of control plane and user plane, the new call can be successfully processed.
2.6 Multiple Clock Sources Multiple clock sources are available for the BSC6810. Thus, the BSC6810 can select system synchronization clocks conveniently.
The available clock sources are as follows:
� Building Integrated Timing Supply System (BITS) � Global Positioning System (GPS) � Line clock extracted from the Iu interface � External 8 kHz clock provided by an external device
The BSC6810 can set a priority for each clock source.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 12 of 65
If the BSC6810 fails to obtain any external clock, the BSC6810 obtains its working timing signals from the local oscillator. The timing signals generated by the local oscillator, however, do not meet the requirements of NodeBs for the clock precision. Therefore, when the BSC6810 uses such timing signals, the NodeBs fail to obtain timing signals from the BSC6810.
2.7 Diverse Transmission Solutions The BSC6810 provides diverse transmission solutions by supporting:
� Multiple Iub Network Topologies � Multiple Types of Transmission Port � High Reliability of Transmission � Flexible Configuration of Interface Boards � IP Transport on the Iub/Iur/Iu Interfaces � Hybrid IP Transport on the Iub Interface � ATM/IP Dual Stack on the Iub Interface � Satellite Transmission on the Iub Interface � Efficient Transmission on the Iub Interface � Dynamic Management of the Bandwidth � Inverse Multiplexing on ATM � Fractional Functions � Timeslot Cross Connection � Multilink PPP
2.7.1 Multiple Iub Network Topologies The BSC6810 supports multiple Iub network topologies, such as star, chain, and tree topologies. The type of topology depends on the site requirement.
2.7.2 Multiple Types of Transmission Port The BSC6810 provides multiple types of physical transmission port for the Iub, Iur, and Iu interfaces.
The ATM transmission ports are of the following types:
� E1/T1 � Unchannelized STM-1/OC-3c � Channelized STM-1/OC-3
The IP transmission ports are of the following types:
� E1/T1 � Unchannelized STM-1/OC-3c � Channelized STM-1/OC-3 � Fast Ethernet (FE) � GE
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 13 of 65
2.7.3 High Reliability of Transmission To achieve high reliability of transmission, the BSC6810 uses the following solutions:
� Transmission port redundancy
− Unchannelized optical ports support Multiplex Section Protection (MSP) 1:1 or MSP 1+1 redundancy.
− Channelized optical ports support MSP 1:1 redundancy.
− FE or GE ports support redundancy and load sharing between the ports. � Diverse ways of fault detection:
− Quick check based on Bi-directional Forwarding Detection (BFD)
− Address Resolution Protocol (ARP) check
− End-to-end ATM Continuous Check (CC) based on the F5 protocol
2.7.4 Flexible Configuration of Interface Boards The BSC6810 does not place restrictions on which slots hold interface boards for the Iub, Iur, or Iu. A subrack can host different types of ATM and IP interface board at the same time.
2.7.5 IP Transport on the Iub/Iur/Iu Interfaces In addition to ATM transport, the BSC6810 supports IP transport on the Iub, Iur, and Iu interfaces. This is consistent with the evolution to an all-IP network, provides sufficient bandwidth for high-speed and large-volume data services, and reduces the cost of construction, operation, and maintenance of transport networks.
2.7.6 Hybrid IP Transport on the Iub Interface When IP transport is applied to the Iub interface, data of different priorities can be transmitted separately through E1/T1 ports and FE ports. The transmission mode of a service depends on the Quality of Service (QoS) requirement. Services with high QoS requirements are transmitted through E1/T1 ports, and those with low QoS requirements are transmitted on the Ethernet.
Hybrid IP transport guarantees the QoS and provides sufficient interface bandwidth for high-speed PS services such as High Speed Downlink Packet Access (HSDPA) and High Speed Uplink Packet Access (HSUPA), thus saving the transmission cost and protecting the investment of operators.
2.7.7 ATM/IP Dual Stack on the Iub Interface ATM/IP dual stack is supported between the BSC6810 and a NodeB. Services with high QoS requirements are transmitted through ATM, while those with low QoS requirements through IP.
Such data transmission guarantees the QoS and provides sufficient interface bandwidth for high-speed PS services such as HSDPA and HSUPA, thus saving the transmission cost and protecting the investment of operators.
2.7.8 Satellite Transmission on the Iub Interface The BSC6810 supports satellite transmission on the Iub interface to cover isolated areas.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 14 of 65
2.7.9 Efficient Transmission on the Iub Interface The BSC6810 improves transmission efficiency by taking the following techniques on the Iub interface:
� Iub overbooking and Frame Protocol Multiplexing (FP MUX)
Without additional transmission devices, the BSC6810 improves the efficiency of transmission on the Iub interface, thus increasing the revenue of operators.
− With Iub overbooking, the BSC6810 can estimate the bandwidth of a service on the Iub interface and allocate an appropriate bandwidth to the service. In this way, the Iub transmission efficiency increases greatly.
− With FP MUX, the BSC6810 can multiplex Iub FP data. That is, the BSC6810 multiplexes multiple User Datagram Protocol (UDP) or IP packets into one data packet in a specific format before transmitting it, thus increasing the efficiency of IP transport on the Iub interface.
� IP shaping/policing
Usually, the links on the NodeB side are low-speed ones. When a high-speed port on the BSC6810 connects to a low-speed port on a NodeB, packet loss may occur if the BSC6810 transmits packets to the NodeB. IP shaping/policing, however, can prevent such packet loss, balance traffic, and improve the efficiency of transmission on the Iub interface.
2.7.10 Dynamic Management of the Bandwidth The BSC6810 detects the IP QoS information, such as the packet loss rate, delay, and delay variation. Based on the QoS, the BSC6810 then adjusts the bandwidth of logical ports and of resource groups. Thus, the transmission efficiency is enhanced.
2.7.11 Inverse Multiplexing on ATM The BSC6810 provides the Inverse Multiplexing on ATM (IMA) function over E1/T1 links. An ATM cell stream from a high-speed transport link is multiplexed inversely onto multiple low-speed E1/T1 links. Then, at the receiver end, the low-speed cell streams are converged to the original high-speed cell stream.
The IMA function enables high-speed transmission through low-speed links. Thus, it broadens the application scope of E1/T1 links. In addition, this function has a relatively high fault tolerance. Provided that the number of working links is not smaller than the specified minimum number of active links in an IMA group, services can continue. Thus, the IMA function ensures high transmission reliability.
2.7.12 Fractional Functions The BSC6810 provides the fractional functions, that is, fractional ATM and fractional IMA. The fractional functions enable 3G equipment to share the E1/T1 links of a 2G network with 2G equipment, thus allowing 2G and 3G concurrent transmission.
With the fractional functions, you can quickly deploy NodeBs at an early stage of WCDMA network construction by using the existing 2G transmission resources. Thus, you can launch the system at a comparatively low cost and within a relatively short period of time.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 15 of 65
2.7.13 Timeslot Cross Connection The BSC6810 supports the timeslot cross connection function. The 2G equipment cross-connects the timeslots on a 2G link to the BSC6810, so as to enable concurrent transmission of 2G and 3G data. Such timeslot cross connection does not require additional timeslot cross connection equipment.
2.7.14 Multilink PPP The BSC6810 provides the Multilink PPP (MLPPP) function. This function combines physically independent links to form only one logical channel. Thus, the network layer can send data directly to this logical channel. The MLPPP function provides a relatively high bandwidth and implements rapid data forwarding.
2.8 Advanced RRM Algorithms The BSC6810 uses Huawei-patented Radio Resource Management (RRM) algorithms in the following functions:
� Power control � Handover � Radio resource allocation � Call Admission Control (CAC) � Load control
In addition, the BSC6810 applies these algorithms in new features such as HSDPA, HSUPA, and Multimedia Broadcast and Multicast Service (MBMS). Thus, the BSC6810 offers optimum network coverage, capacity, and quality.
2.8.1 Power Control The BSC6810 uses outer loop power control algorithms. It aims to provide the required quality for UEs when the radio environment changes and to increase the usage of system capacity.
2.8.2 Handover The BSC6810 supports flexible handover strategies and parameter configurations. Based on different coverage areas, services and loads, it performs different kinds of handover, such as intra-frequency handover, inter-frequency handover, and inter-RAT handover. Thus, it improves the speech quality, reduces the call drop rate, and implements traffic absorption in special areas.
2.8.3 Radio Resource Allocation Based on the QoS requirements, actual traffic volume, and actual cell load, the BSC6810 can allocate resources dynamically. Thus, it fulfills the communication requirements and increases the efficiency of radio channel resources.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 16 of 65
2.8.4 CAC and Load Control The BSC6810 applies multiple Huawei-patented technologies, such as load sharing and admission based on rate downsizing, to balance loads between cells and to control service access. Thus, it increases the system capacity and guarantees the current QoS.
2.8.5 Service Differentiation Based on Subscriber P riorities Based on the allocation retention priorities set at the CN for subscribers, the BSC6810 can set the subscribers to three levels: gold, silver, and bronze. The BSC6810 then provides different services for the three levels of subscribers.
� Based on priorities of subscribers, the BSC6810 sets different Guaranteed Bit Rates (GBRs) for Best Effort (BE) services of different subscribers. GBR guarantees that the basic requirements of BE services are met.
� With the pre-emption algorithm, high-priority subscribers can pre-empt the resources over low-priority subscribers.
� With the algorithm of rate downsizing against congestion, the BSC6810 preferentially downsizes the rates of low-priority subscribers to their GBRs.
� With the scheduling algorithm, the BSC6810 proportionally allocates bandwidths to subscribers. This algorithm takes subscriber priorities into account in the condition that the GBRs of the subscribers are guaranteed.
� With the flow control algorithm, the BSC6810 proportionally allocates bandwidths to subscribers. This algorithm takes subscriber priorities into account in the condition that the GBRs of the subscribers are guaranteed.
When radio resources are limited, the BSC6810 can guarantee GBRs of subscribers before allocating the remaining resources proportionally.
2.9 Advanced Solutions to Radio Data Services The BSC6810 adopts the advanced technologies, such as HSDPA, HSUPA, and MBMS, to meet the requirements of different types of data service.
2.9.1 HSDPA The BSC6810 adopts HSDPA as the solution for high-speed DL data transmission. The DL rate for a single UE can reach up to 14.4 Mbit/s on the physical sublayer.
In addition, the BSC6810 supports VoIP over HSDPA and IMS over HSDPA, where VoIP stands for Voice over IP and IMS stands for IP Multimedia Subsystem.
HSDPA enhances the performance of the WCDMA network in the following aspects:
� Higher DL data rate � Shorter service delay and more pleasant user experience in high-speed services � More efficient DL coding and power utilization
2.9.2 HSUPA The BSC6810 adopts HSUPA as the solution for high-speed UL data transmission. The UL rate for a single UE can reach up to 5.76 Mbit/s on the physical sublayer.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 17 of 65
In addition, the BSC6810 supports VoIP over HSUPA and IMS over HSUPA.
HSUPA enhances the performance of the WCDMA network in the following aspects:
� Higher UL data rate � Shorter service delay and more pleasant user experience in high-speed services � Faster UL resource control � Better quality of service
2.9.3 MBMS The BSC6810 adopts MBMS to provide the high-speed multimedia broadcast service. The transmission rate of MBMS services can reach up to 256 kbit/s.
MBMS enhances resource efficiency and provides diversified multimedia services.
2.10 High Compatibility of Protocols The BSC6810 is developed according to 3GPP R6 specifications. It is compatible with other Network Elements (NEs) and UEs based on 3GPP R6, R5, R4, or R99 specifications.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 18 of 65
3 System Architecture
3.1 About This Chapter This chapter consists of the following sections:
� Physical Structure � Logical Structure � Hardware Configuration
3.2 Physical Structure
3.2.1 Cabinet Appearance The BSC6810 uses the standard N68E-22 or N68-21-N cabinet of Huawei. The design complies with the IEC60297 and IEEE standards.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 19 of 65
Figure 3-1 shows the cabinet.
Figure 3-1 BSC6810 cabinet
3.2.2 Cabinet Components The BSC6810 has the following two types of cabinet:
� RNC Switching Rack (RSR) � RNC Business Rack (RBR)
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 20 of 65
Figure 3-2 shows the components of the cabinets.
Figure 3-2 Components of the BSC6810 cabinets
RBS
RSR RBR
RBS
RBS
RBS
Power distribution box Power distribution box
RSS
RINT
RINT
RINT
RINT
RINT
RINT
GCUa
DPUb
DPUb
GCUa
SCUa
SPUa
SPUa
SPUa
SPUa
SCUa
DPUb
DPUb
RBS
SPUa
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
SPUa
DPUb
DPUb
DPUb
DPUb
SCUa
SPUa
SPUa
SPUa
SPUa
SCUa
DPUb
DPUb
SPUa
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
SPUa
DPUb
DPUb
DPUb
DPUb
SCUa
SPUa
SPUa
SPUa
SPUa
SCUa
DPUb
DPUb
SPUa
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
SPUa
DPUb
DPUb
DPUb
DPUb
SCUa
SPUa
SPUa
SPUa
SPUa
SCUa
DPUb
DPUb
SPUa
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
SPUa
DPUb
DPUb
DPUb
DPUb
SCUa
SPUa
SPUa
SPUa
SPUa
SCUa
DPUb
DPUb
SPUa
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
SPUa
DPUb
DPUb
DPUb
DPUb
SCUa
SPUa
SPUa
SPUa
SPUa
SCUa
DPUb
DPUb
OMUa
OMUa
RINT
RINT
RINT
RINT
SPUa
SPUa
The RINT refers to the interface board of the BSC6810. Physically, there is no board named RINT.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 21 of 65
RSR
The RSR provides the single-cabinet solution.
The RSR has the following components:
� One RNC Switching Subrack (RSS) � Zero to two RNC Business Subracks (RBSs)
RBR
The RBR is configured when the required service processing capability exceeds the specifications for the RSR. At most one RBR can be configured.
The RBR is configured with only RBSs. The number of RBSs in the RBR ranges from 1 to 3. If the RBR is configured with one or two RBSs, the RBSs should be configured from the bottom to the top.
3.2.3 Subrack Components The BSC6810 has two types of subrack, according to board configuration. They are the RSS and the RBS. The BSC6810 can be configured with up to six subracks. Among the subracks, one is the RSS, and the others are RBSs. The number of RBSs ranges from 0 to 5.
The subracks of the BSC6810 have a standard width of 19 inches, which complies with the IEC60297 standard. The height of a single subrack is 12 U. In a subrack, the backplane is positioned in the middle, and front and rear boards are installed on both sides of the backplane, as shown in Figure 3-3. The slots are of the same length.
Figure 3-3 Subrack of the BSC6810
A
C
B
0 13
14 27
6
20
A: front boards B: backplane C: rear boards
Each subrack of the BSC6810 provides a total of 28 slots. The 14 slots on the front side of the backplane are numbered from 0 to 13, and those on the rear side from 14 to 27.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 22 of 65
On each plane from leftmost to rightmost, every two even- and odd-numbered neighboring slots have an active/standby relationship. For example, slots 0 and 1 are active/standby slots. The same is true for slots 2 and 3. Only the boards that work in active/standby mode must be installed in active/standby slots.
3.2.4 RSS Subrack The mandatory RSS is configured at the bottom of the RSR. The RSS is the central switching subrack of the BSC6810.
This subrack has the following functions:
� Connecting to each RBS and transferring data between RBSs through data switching on the MAC sublayer
� Providing system timing signals � Providing the same service processing functions as the RBS � Serving physical transmission on the Iub, Iur, and Iu interfaces � Performing OM management of the Back Administration Module (BAM)
Figure 3-4 shows the boards in the RSS.
Figure 3-4 Boards in the RSS
1311975310 2 4 6 8 10 12
2725232119171514 16 18 20 22 24
GCUa
DPUb
DPUb
GCUa
SCUa
SPUa
SPUa
SPUa
SPUa
SCUa
DPUb
DPUb
26
OMUa
OMUa
RINT
RINT
RINT
RINT
SPUa
SPUa
RINT
RINT
RINT
RINT
RINT
RINT
Figure 3-4 presents only an example of board configuration. You can change the configuration as required.
The RSS provides 28 slots. Table 3-1 describes the boards in the RSS.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 23 of 65
Table 3-1 Boards in the RSS
Board Full Spelling Function Configuration
DPUb RNC Data Processing Unit REV:b
Processing and distributing service data on the user plane
The following slots are available for the DPUb: � Slots 8–11 and 14–19
in the RSS � Slots 8–19 in an RBS
GCUa RNC General Clock Unit REV:a
� Performing phase-lock and hold on the system clock
� Generating RNC Frame Number (RFN) signals for the system
Two boards are permanently configured in slots 12 and 13 of the RSS.
GCGa RNC General Clock with GPS Card REV:a
Having all the functions of the GCUa; in addition, receiving and processing GPS signals
Two boards are permanently configured in slots 12 and 13 of the RSS.
OMUa RNC Operation and Maintenance Unit REV:a
� Performing configuration management, performance management, fault management, security management, loading management, and so on
� Working as the OM agent of the M2000 and Local Maintenance Terminals (LMTs) to provide the BSC6810 OM interface for the M2000 and LMTs and to control communication between the BSC6810 and the M2000/LMTs
One board is permanently configured in slots 20 and 21 of the RSS, and the other in slots 22 and 23.
SCUa RNC GE Switching and Control Unit REV:a
� Providing MAC switching, and enabling convergence of ATM and IP networks
� Providing 60 Gbit/s switching capacity
� Providing the port trunking function � Enabling inter-subrack connections � Providing configuration and
maintenance of a subrack or of the whole BSC6810
� Distributing timing signals and RFN signals for the BSC6810
Two boards are permanently configured in slots 6 and 7.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 24 of 65
Board Full Spelling Function Configuration
SPUa RNC Signaling Processing Unit REV:a
� Processing high-layer signaling of the Uu, Iu, Iur, and Iub interfaces
� Processing transport layer signaling � Allocating and managing various
resources necessary to service setup, and establishing signaling and service connections
� Providing 4 independent processor systems
� Processing RFN signals
The following slots are available for the SPUa: � Slots 0–5 and 8–11 in
the RSS � Slots 0–5 and 8–11 in
an RBS
AEUa
RNC 32-port ATM over E1/T1/J1 Interface Unit REV:a
� Providing 32 E1s/T1s � Providing ATM over E1/T1 � Providing 32 IMA groups or 32 UNI
links (Each IMA group contains a maximum of 32 IMA links.)
� Providing the fractional ATM and fractional IMA functions
� Providing the timeslot cross connection function
� Providing ATM Adaptation Layer 2 (AAL2) switching
� Extracting the clock from E1/T1 links, exporting 2 MHz signals, and sending the 2 MHz timing signals to the GCUa/GCGa
The following slots are available for the AEUa: � Slots 14–19 and
24–27 in the RSS � Slots 14–27 in an
RBS
AOUa
RNC 2-port ATM over Channelized Optical STM-1/OC-3 Interface Unit REV:a
� Providing 2 STM-1/OC-3 optical ports � Providing 126 E1s or 168 T1s � Providing ATM over E1/T1 over SDH � Providing the IMA and UNI functions � Providing 84 IMA groups, each of
which contains 32 E1s/T1s � Providing AAL2 switching � Receiving timing signals from
upper-level equipment and sending them to the GCUa/GCGa
� Providing timing signals for NodeBs
The following slots are available for the AOUa: � Slots 14–19 and
24–27 in the RSS � Slots 14–27 in an
RBS
RINT
UOIa
RNC 4-port ATM/Packet over Unchannelized Optical STM-1/OC-3c Interface Unit REV:a
� Providing 4 STM-1/OC-3c optical ports
� Providing ATM over SDH or IP over SDH
� Receiving timing signals from upper-level equipment and sending them to the GCUa/GCGa
� Providing timing signals for NodeBs
The following slots are available for the UOIa: � Slots 14–19 and
24–27 in the RSS � Slots 14–27 in an
RBS
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 25 of 65
Board Full Spelling Function Configuration
PEUa
RNC 32-port Packet over E1/T1/J1 Interface Unit REV:a
� Providing 32 E1s/T1s � Providing IP over PPP/MLPPP over
E1/T1 � Providing 128 Point-to-Point Protocol
(PPP) links or 64 MLPPP groups (Each MLPPP group contains a maximum of 8 MLPPP links.)
� Providing the timeslot cross connection function
� Receiving timing signals from upper-level equipment and sending them to the GCUa/GCGa
� Providing timing signals for NodeBs
The following slots are available for the PEUa: � Slots 14–19 and
24–27 in the RSS � Slots 14–27 in an
RBS
POUa
RNC 2-port IP over Channelized Optical STM-1/OC-3 Interface Unit REV:a
� Providing 2 STM-1/OC-3 optical ports � Providing 126 E1s or 168 T1s � Providing IP over E1/T1 over SDH � Receiving timing signals from
upper-level equipment and sending them to the GCUa/GCGa
� Providing timing signals for NodeBs
The following slots are available for the POUa: � Slots 14–19 and
24–27 in the RSS � Slots 14–27 in an
RBS
FG2a
RNC Packet over Electrical 8-port FE or 2-port GE Ethernet Interface Unit REV:a
� Providing 8 FE ports or 2 GE electrical ports
� Providing IP over FE or IP over GE
The following slots are available for the FG2a: � Slots 14–19 and
24–27 in the RSS � Slots 14–27 in an
RBS
GOUa
RNC 2-port Packet over Optical GE Ethernet Interface Unit REV:a
� Providing 2 GE optical ports � Providing IP over GE
The following slots are available for the GOUa: � Slots 14–19 and
24–27 in the RSS � Slots 14–27 in an
RBS
The RSS can be configured with one or two OMUa boards. In the latter case, the two boards work in active/standby mode.
3.2.5 RBS Subrack The optional RBS is configured in the RSR or the RBR. The RBS is the basic service processing subrack of the BSC6810. Working as the extension subrack of the RSS, the RBS is used to extend the service processing capability of the BSC6810. This subrack has the following functions:
� Processing signaling on the control plane � Processing and distributing service data on the user plane � Serving physical transmission on the Iub, Iur, and Iu interfaces
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 26 of 65
Figure 3-5 shows the boards in the RBS.
Figure 3-5 Boards in the RBS
1311975310 2 4 6 8 10 12
2725232119171514 16 18 20 22 24 26
SPUa
SPUa
DPUb
DPUb
DPUb
DPUb
SCUa
SPUa
SPUa
SPUa
SPUa
SCUa
DPUb
DPUb
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
RINT
Figure 3-5 presents only an example of board configuration. You can change the configuration as required.
The RBS provides 28 slots. The RBS holds all types of board in the RSS except the GCUa/GCGa and OMUa.
3.3 Logical Structure The BSC6810 consists of the following functional modules:
� Internal Switching Module � User Plane Data Processing Module � Control Plane Data Processing Module � Clock Module � Transmission Interface Module � OM Module
3.3.1 Internal Switching Module The internal switching module is mainly implemented by the SCUa boards. The SCUa in the RSS performs first-level switching and that in the RBS performs second-level switching. Thus, the BSC6810 provides internal MAC switching at two levels. The two-level switching enables full connection between all modules of the BSC6810.
3.3.2 User Plane Data Processing Module The user plane data processing module is mainly implemented by the DPUb boards. This module performs protocol processing at each layer on the user plane data for the RNC.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 27 of 65
The DPUb boards perform the following protocol:
� Frame Protocol (FP) � MDC � MAC � RLC � PDCP � Iu User Plane (Iu UP) protocols � GTP-U
3.3.3 Control Plane Data Processing Module The control plane data processing module is mainly implemented by the SPUa boards. This module processes control plane signaling on each interface for the RNC. The processed messages are of the following types:
� Radio Access Network Application Part (RANAP) � NodeB Application Part (NBAP) � Radio Network Subsystem Application Part (RNSAP) � Radio Resource Control (RRC) � Service Area Broadcast Protocol (SABP)
The SPUa boards are configured in both the RSS and RBSs.
3.3.4 Clock Module The clock module is mainly implemented by the GCUa/GCGa boards and the clock processing units of other boards. This module provides the clock for the operation of the RNC, generates RFN signals, and provides NodeBs with timing signals.
The GCUa/GCGa boards are configured only in the RSS. If the RNC requires GPS signals, the GCGa is required.
3.3.5 Transmission Interface Module The transmission interface module is mainly implemented by the AEUa, AOUa, UOIa, PEUa, POUa, FG2a, or GOUa boards. This module provides the transmission interface between the BSC6810 and other NEs. In addition, it performs related protocol processing at the transport network layer.
For ATM transport, the AAL2 and ATM Adaptation Layer 5 (AAL5) messages are terminated at the transmission interface module.
For IP transport, this module processes UDP and IP messages on the user plane and forwards IP messages on the control plane.
3.3.6 OM Module The OM module is mainly implemented by the LMT, BAM, and related modules of host boards. This module performs operation and maintenance on the BSC6810.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 28 of 65
3.4 Hardware Configuration
3.4.1 Minimum Configuration In minimum configuration, the BSC6810 needs only one RSR that has only the RSS. The minimum configuration applies to an early stage of construction of a commercial network.
Figure 3-6 shows the minimum configuration of the BSC6810.
Figure 3-6 Minimum configuration of the BSC6810
RSS
Cabinet 1
Empty
Empty
The maximum capacity of the BSC6810 in minimum configuration is as follows:
� 6,000 Erlang voice traffic or 384 Mbit/s (UL + DL) PS throughput � 200 NodeBs � 600 cells
3.4.2 Maximum Configuration In maximum configuration, the BSC6810 needs two cabinets, that is, one RSR and one RBR. You can add RBSs to expand the system capacity without disrupting ongoing services.
Figure 3-7 shows the maximum configuration of the BSC6810.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 29 of 65
Figure 3-7 Maximum configuration of the BSC6810
RBS
Cabinet 2
RBS
RBS
RSS
Cabinet 1
RBS
RBS
The maximum capacity of the BSC6810 in maximum configuration is as follows:
� 51,000 Erlang voice traffic or 3,264 Mbit/s (UL + DL) PS throughput � 1,700 NodeBs � 5,100 cells
3.4.3 Typical Configurations Table 3-2 shows the typical configurations of the BSC6810. You can choose a typical configuration as required.
Table 3-2 Typical configurations of the BSC6810
Number of Subracks
BHCA Voice Traffic (Erlang)
(UL + DL) PS Throughput (Mbit/s)
Number of NodeBs
Number of Cells
1 RSS 160,000 6,000 384 200 600
1 RSS + 1 RBS 400,000 15,000 960 500 1,500
1 RSS + 2 RBSs 640,000 24,000 1,536 800 2,400
1 RSS + 3 RBSs 880,000 33,000 2,112 1,100 3,300
1 RSS + 4 RBSs 1,120,000 42,000 2,688 1,400 4,200
1 RSS + 5 RBSs 1,360,000 51,000 3,264 1,700 5,100
Note: BHCA: Busy Hour Call Attempt
The values of BHCA and voice traffic are calculated on the basis of Huawei traffic model.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 30 of 65
3.4.4 Hardware Expansion Schemes You can expand the capacity of the BSC6810 by adding RBSs or service processing boards. The addition of SPUa boards contributes to the expansion of control plane resources, and the addition of DPUb boards contributes to the expansion of user plane resources.
When adding boards, note the following items:
� In the RSS, SPUa boards can be configured in slots 0–5 and 8–11. The maximum number of SPUa boards in the RSS is 10. In an RBS, SPUa boards can be configured in slots 0–5 and 8–11. The maximum number of SPUa boards in an RBS is 10.
� In the RSS, DPUb boards can be configured in slots 8–11 and 14–19. The maximum number of DPUb boards in the RSS is 10. In an RBS, DPUb boards can be configured in slots 8–19. The maximum number of DPUb boards in an RBS is 12.
Table 3-3 lists the processing capabilities of SPUa and DPUb boards. The processing capability of the SPUa can be calculated on the basis of the capability of each SPU subsystem.
Table 3-3 Processing capability of a single SPU subsystem or DPUb board
Board or Subsystem
BHCA Voice Traffic (Erlang)
(UL + DL) PS Throughput (Mbit/s)
SPU subsystem
20,000 – –
DPUb – 1,500 96
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 31 of 65
4 Operation and Maintenance
4.1 About This Chapter This chapter consists of the following sections:
� OM Structure � OM Functions
4.2 OM Structure Figure 4-1 shows the OM system of the BSC6810. The system consists of the Front Administration Module (FAM), BAM, OM terminals and alarm box. These components are described as follows:
� The FAM consists of the boards in the RSS and RBSs. It is the OM object entity. � The physical entity of the BAM is the OMUa boards in the RSS. The BAM collects
and processes OM information and sends the information to LMTs and the iManager M2000.
� The LMTs are OM terminals on the BSC6810 side. The iManager M2000 is a centralized OM system.
� The alarm box provides audible and visible alarms.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 32 of 65
Figure 4-1 OM system of the BSC6810
VLAN
BAM
iManager M2000
LMTLMT
FAM
OM system of the BSC6810
Alarm box
VLAN
IP
BAM: Back Administration Module FAM: Front Administration Module LMT: Local Maintenance Terminal IP: Internet Protocol VLAN: Virtual Local Area Network
The LMT is the OM terminal on the NE side. It can access the BAM through Virtual Local Area Network (VLAN), an intranet, and the Internet.
The LMT is an intelligent Man Machine Language (MML) client working in Graphic User Interface (GUI) mode. It provides the BSC6810 with OM functions.
Through an external alarm box, the LMT can report audible and visible alarms if faults are detected.
4.3 OM Functions The BSC6810 provides MML commands and GUIs as an interface for system management, configuration, maintenance, alarm management, and so on. Such an interface is explicit and easy to use. In addition, the BSC6810 can check the data integrity for an MML command to be run.
This section describes the following OM functions:
� Security Management � Configuration Management � Maintenance Management � Fault Detection
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 33 of 65
� Performance Management � Alarm Management � Loading Management � Status Monitoring � Message Tracing � Log Management � Software Management
4.3.1 Security Management BSC6810 security management provides the following functions:
� Grade-based operator right setting
You can set the operator right, operation time limit, and password to ensure system security and operation flexibility.
� Operator information protection
If no operation is performed for a certain period, the user interface is automatically locked.
� File Transfer Protocol (FTP) transmission based on ciphering
This ensures the security of FTP transmission. � Encryption of the communication interface between the BSC6810 and the
Element Management System (EMS)
The BSC6810 uses the Security Socket Layer (SSL) protocol to fulfill transmission of ciphertext over the OM channel between the BSC6810 and the EMS. This ensures data security.
4.3.2 Configuration Management The BSC6810 provides certain functions for configuration management. These functions are described in the following topics.
Automatic Data Configuration
The BSC6810 can automatically generate the configuration data that is necessary for internal physical and logical connections and configure the data for the corresponding parts. No manual configuration is required. You need to configure only the data for connections between the BSC6810 and external devices, thus improving the serviceability of the BSC6810.
Online and Offline Data Configuration
The BSC6810 supports the following configuration modes:
� Offline data configuration
In offline data configuration mode, configuration data is stored only in the BAM. The data is not sent to the host before being loaded onto the host. Therefore, this mode increases the efficiency of configuring a large amount of data. The BSC6810 also supports offline data configuration based on host subracks. Therefore, it allows capacity expansion without disrupting services.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 34 of 65
� Online data configuration
In online data configuration mode, configuration data is sent to the host immediately after the configuration. There is no need to reset the BSC6810 or to reload the data. Thus, dynamic data configuration is enabled.
Dynamic Batch Data Configuration
The BSC6810 supports dynamic configuration of data in batches. With this function, the batch data configuration scripts are executed when the BSC6810 is offline. After the BSC6810 switches to the online mode, the BAM sends all the configuration data to the host in batches. The data takes effect with no need to restart or reset the subracks or boards. This avoids disrupting ongoing services.
In the case of bulk data modification, such as NodeB reparent and change of interface board types, dynamic batch data configuration improves efficiency.
Data Configuration Right Control
Under data configuration right control, only one user has the right to perform data configuration for the BSC6810 at any time. The configuration is allowed on only one configuration console at a time, that is, either on the LMT or on the M2000.
With the control, data configuration on the LMT and that on the M2000 are not allowed at the same time, thus improving reliability of the BSC6810.
Data Configuration Rollback
The BSC6810 provides the data configuration rollback function. If data configuration fails to achieve the expectation or even causes equipment or network exceptions, you can perform rollback to restore the configurations quickly. This ensures proper running of the BSC6810.
Data Backup
When two OMUa boards are configured, they work in active/standby mode. The data on the standby OMUa is synchronized with that on the active OMUa. The BSC6810 supports automatic and manual data backup. It provides a data backup and recovery tool.
Data Validity Check
The BSC6810 can check the integrity and consistency of configuration data, such as the data of a cell.
Configuration Data Query
The BSC6810 supports the object-based query of configuration data.
Online Reconfiguration of the RINT and Backup Mode
The BSC6810 supports online reconfiguration of the RINT and of the board and port redundancy mode, thus facilitating reconfiguration of services.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 35 of 65
Dynamic Assignment of IP Addresses to a NodeB
When ATM transport is applied to the Iub interface, the BSC6810 uses the Bootstrap Protocol (BOOTP) to automatically assign the OM IP address to a NodeB.
When IP transport is applied to the Iub interface, the BSC6810 uses the Dynamic Host Configuration Protocol (DHCP) to automatically assign the OM IP address to the NodeB.
Compared with BOOTP, DHCP has relatively powerful functions. In addition, DHCP is compatible with BOOTP.
Network Parameter Setting
The radio network parameters of the BSC6810 are of two types: RNC-oriented and cell-oriented. They can adapt to different radio environments.
4.3.3 Maintenance Management The BSC6810 provides certain functions for maintenance management. These functions are described in the following topics.
Board Maintenance
The BSC6810 supports the following board maintenance functions:
� Resets on different levels, including equipment reset, subrack reset, board reset, and subsystem reset
� Query of board reset causes � Hot swap � Setting of boards to the out-of-service state for troubleshooting � Query of board status and version information � Board self-detection and board diagnosis test � Query of the Central Processing Unit (CPU) usage of a board subsystem � Forced active/standby board switchover initiated on the LMT
Object Status Query
The BSC6810 supports the query of the status of certain objects, the reasons for status changes, and the time when the status changes. The objects are as follows:
� Equipment objects, such as boards, subsystems, Digital Signal Processors (DSPs), clocks, optical ports, and BAM
� Physical transmission resource objects, such as E1/T1 links, IMA links, and UNI links
� IP transport links, such as PPP links and MLPPP links � Logical transmission resource objects, such as Signaling ATM Adaptation Layer
(SAAL) links, Stream Control Transmission Protocol (SCTP) links, Message Transfer Part level 3 - broadband (MTP3-b) links, AAL2 paths, IP paths, NodeB Control Ports (NCPs), and Communication Control Ports (CCPs)
� Radio resource objects, such as cells and channels
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 36 of 65
Panel Emulation
The emulated panel on the LMT interface can display the status of boards, Light Emitting Diodes (LEDs) on boards, external physical ports, and DSPs.
Physical Link Maintenance
The BSC6810 supports the status query and loopback test of physical links.
Logical Link Maintenance
The BSC6810 supports the following logical link maintenance functions:
� Status query, activation, and deactivation of Signaling System No. 7 (SS7) signaling links
� Status query of SAAL links and SCTP links � Query about the status of IP traffic channels, and dynamic adjustment of the IP
bandwidth � Status query, blocking, unblocking, and reset of AAL2 traffic channels � Status query and reset of PPP links, MLPPP links, and MLPPP groups � Status query of IMA groups, UNI links, and IMA links � Loopback test � ATM F5 end-to-end detection
SS7 Signaling Point Maintenance
The BSC6810 supports maintenance of SS7 signaling points. The maintenance includes query, inhibit and uninhibit of destination signaling points.
Measurement of Out-of-Service NodeBs or Cells
If a NodeB or cell is out of service, it is unavailable.
The BSC6810 supports the measurement of out-of-service duration and out-of-service ratio. The measurement results can be used to analyze the general serving states of NodeBs or cells.
NodeB Blocking and Unblocking
The BSC6810 can block a NodeB by deactivating all the cells controlled by this NodeB. The BSC6810 can also unblock a NodeB by activating all of the cells controlled by this NodeB.
Cell Blocking and Unblocking
The BSC6810 can block or unblock cells.
When a cell is blocked, all the connections to the cell are released, and the cell becomes unavailable. After it is unblocked, the cell recovers to be available.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 37 of 65
Guarantee for VIP Cells and NodeBs
The BSC6810 can provide OM guarantee and service guarantee for VIP cells and NodeBs. Thus, the VIP cells and NodeBs can run stably with high quality of service.
� OM guarantee means monitoring VIP cells and NodeBs through detailed monitoring items on a specific interface, so that the maintenance engineers can identify faults rapidly and rectify them efficiently.
� Service guarantee means providing special network planning and configuration for VIP cells and NodeBs, so that they can provide better services. The resources shared between VIP cells, VIP NodeBs, common cells, and common NodeBs are offered preferentially to VIP cells and VIP NodeBs.
Remote Maintenance
The BSC6810 supports remote maintenance by allowing remote access through the Internet or Virtual Private Network (VPN).
Provision of OM Channels for the NodeBs
The BSC6810 provides the following OM channels for NodeBs:
� Transparent OM channels, through which you can operate and maintain NodeBs on the LMT of the BSC6810 or on the M2000
� Reverse OM channels, through which you can operate and maintain other NodeBs on the local NodeB
4.3.4 Fault Detection The BSC6810 provides physical layer fault detection, data link layer fault detection, and other fault detection.
Physical layer fault detection covers the following aspects:
� Local E1 loopback test � Remote E1 loopback test � E1 Bit Error Rate (BER) test � E1 loopback detection � E1 misconnection test � SDH loopback detection � FE/GE port fault detection
Data link layer fault detection covers the following aspects:
� AAL2 path fault detection � IP path fault detection � SAAL fault detection � SCTP fault detection � PPP/MLPPP misconnection test � NodeB OM IP over ATM (IPoA) fault detection � Iu-PS IPoA fault detection � Virtual Connect Link (VCL) CC
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 38 of 65
Other fault detection covers the following aspects:
� Inter-Process Communication (IPC) connectivity check � Cell common channel fault detection � RFN fault detection � Clock fault detection � Board loading control fault detection
4.3.5 Performance Management The BSC6810 provides various performance counters for the upper-layer Network Management System (NMS) to facilitate performance analysis and network optimization.
By default, the BSC6810 supports two measurement periods. One is the normal period whose duration is 30 minutes, and the other is the short period whose duration is 5 minutes. The latter is used to monitor Key Performance Indicators (KPIs) in real time.
A measurement item supports both measurement periods, that is, a measurement item can be included in both a normal-period task and a short-period task.
You can register various performance measurement tasks on the M2000. The BSC6810 can store measurement results generated in the past 72 hours.
4.3.6 Alarm Management The BSC6810 provides advanced fault diagnosis and handling methods, performs relevance analysis of alarms raised from the host, and reports valid alarms to the user.
The BSC6810 provides certain functions for maintenance management. These functions are described in the following topics.
Alarm Processing
You can browse alarm information in real time, query history alarm information, and store alarm information. The online help provides detailed troubleshooting methods for each alarm.
The BSC6810 can store the history alarm information generated in the past 90 days and at most 100,000 alarms.
Alarm Masking
The BSC6810 allows you to mask derivative alarms to reduce the number of the reported alarms.
Alarm Filtering
The BSC6810 can filter the alarms of a specific object. If an object is filtered, the alarms of this object are not sent to the alarm management system.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 39 of 65
Alarm Indication
When a fault alarm is generated, the BSC6810 can notify you in the following ways: blinking of the icon, audible indication of the terminal, and audible and visible indications on the alarm box.
Classified Alarm Management
The BSC6810 supports classified management of alarms raised from normal cells and NodeBs and from abnormal ones. The latter can be the following cells and NodeBs: those under commissioning and those not put into use.
4.3.7 Loading Management The following modes are available for loading program files and data files onto boards of the BSC6810:
� Loading from the flash memories of the boards � Loading from the BAM
The mode of loading program files and data files onto a board depends on the consistency between the files in the flash memory of the board and those in the BAM. See specifics as follows:
� If the files are consistent, the board loads the files from its flash memory. � If the files are inconsistent, the board loads the files from the BAM and updates
the files in the flash memory of the active workspace on the board, so as to ensure the program and data consistency.
4.3.8 Status Monitoring The BSC6810 can monitor in real time the system status, including CPU usage, cell performance, connection performance, link performance, and board resources.
The BSC6810 can monitor the following cell performance:
� Pilot transmit (TX) power of the Primary Common Pilot Channel (P-CPICH) � UL Received Total Wideband Power (RTWP) � DL frequency TX power � Number of UEs, including UEs on Dedicated Channels (DCHs), UEs on common
channels, HSDPA UEs, and HSUPA UEs � Node synchronization � UL CAC � DL CAC � UL equivalent number of users � DL equivalent number of users � Usage of the code tree � Minimum High Speed Downlink Shared Channel (HS-DSCH) power requirement � Bit rate provided by the HS-DSCH � Bit rate provided by the Enhanced Dedicated Channel (E-DCH)
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 40 of 65
The BSC6810 can monitor the following connection performance:
� Signal-to-Noise Ratio (SNR) and receive (RX) signal code power of a cell � Measurement value of Signal-to-Interference Ratio (SIR) of a UL radio link set � SIR target of a UL radio link set � SIR error value of a UL radio link set � Block Error Rate (BLER) of a UL transport channel � BLER of a DL transport channel � DL code TX power � UE TX power � BER of a UL physical channel � UL traffic volume � DL traffic volume � UL throughput and bandwidth � DL throughput and bandwidth � Handover delay � Adaptive Multi Rate (AMR) mode
The BSC6810 can monitor the following link performance:
� IMA groups � UNI links � Fractional ATM links � SAAL links � IPoA Permanent Virtual Channels (PVCs) � IP path QoS � AAL2 paths � IP paths � FE/GE traffic � Traffic on PPP links � Traffic on MLPPP groups � Traffic on SCTP links
The BSC6810 can monitor the board resource, that is, the license.
4.3.9 Message Tracing The BSC6810 can perform the following types of message tracing:
� Message tracing on standard interfaces � Protocol message tracing on the transport layer � Call tracing � Tracing on missed neighboring cell configuration � Cell message tracing � Intra-system inter-module message tracing � Message tracing on the serial port after redirection
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 41 of 65
� IP tracing � Call Data Tracing (CDT) � CellDT message tracing � Location message tracing
The function of message tracing is integrated into the LMT, which facilitates problem identification. The BSC6810 also provides a tool called Trace Viewer, which allows you to view the stored messages.
4.3.10 Log Management Various logs are available for you to know the running state of the BSC6810 and to troubleshoot faults. The BSC6810 provides the following logs:
� Operation log: records the operation information of operators in real time. � Running log: records the running information of the BSC6810 in real time. � Subscriber log: records the calling procedure information, which, in case of
calling failure, is exported to the BAM for problem identification. � Cell log: records the cell procedure information, which, in case of cell abnormality,
is exported to the BAM for problem identification.
4.3.11 Software Management The BSC6810 provides certain functions for software management. These functions are described in the following topics.
Online Patching
The BSC6810 supports online patching without disrupting ongoing services.
Patches are provided in patch packages. The BSC6810 supports totally and, in some cases, partially one-push solution to facilitate the upgrade. In addition, it supports version rollback, which guarantees the stability of the system.
Remote Upgrade
The BSC6810 supports remote upgrade. You can upgrade it on a remote terminal. In addition, the BSC6810 provides automatic upgrade tools, which can reduce human interference and errors.
Remote Patching
The BSC6810 supports remote patching. You can perform the following operations on a remote terminal:
� Patching the BAM
The patches include Windows operating system patches of hotfix type and BAM software patches.
� Patching the host of the BSC6810
The patches are specific for DSPs and .bin program files. � Querying all the patches on the BSC6810 through MML commands
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 42 of 65
Online Upgrade of BIOS
The BSC6810 supports online upgrade of the Basic Input Output System (BIOS). It can load BootROM software onto boards through MML commands without disrupting ongoing services.
Online Expansion
You can expand the capacity of the BSC6810 by adding RBSs or service processing boards. After startup, the new board can automatically load programs, obtain intra-system connection data and configuration data, and enter the serving state.
Batch Command Processing
The BSC6810 supports the editing and modification of commands in batches.
Scheduled Task Processing
The BSC6810 supports scheduled tasks. You can preset commands in the system. The system will automatically run the commands at the preset time.
Online Help
The BSC6810 provides the GUI-based online help.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 43 of 65
5 Reliability
5.1 About This Chapter This chapter consists of the following sections:
� System Reliability � Hardware Reliability � Software Reliability
5.2 System Reliability The system reliability design of the BSC6810 takes into account the following techniques:
� Load control
The system performs load control based on the CPU usage, traffic over each interface, and radio resource load of the system. Thus, the BSC6810 can keep on working in case of CPU overload and resource congestion. In this way, the system reliability is enhanced.
� Dynamic sharing of resources in the system
The DPUb boards and DSPs work in resource pool mode, that is, all the DSPs in a subrack work as a resource pool. The MPU in a subrack manages and allocates all the user plane resources within the subrack to fulfill intra-subrack sharing of user plane resources.
In case of overload, the MPU forwards Radio Resource Control (RRC) connection requests to other subracks, so as to fulfill inter-subrack sharing of user plane resources and intra- and inter-subrack sharing of control plane resources.
� Port trunking
SCUa boards support port trunking. This function allows data backup in case of link failure, thus preventing inter-plane switchover and cascading switchover and improving the reliability of intra-system communication.
� Dual planes for timing signal transmission
The BSC6810 provides the dual planes for transmission of timing signals between the GCUa/GCGa and SCUa boards.
The active and standby GCUa/GCGa boards are connected to the active and standby SCUa boards through the Y-shaped cables. This connection mode ensures proper working of the timing signals for the system if a single-point failure
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 44 of 65
occurs to the GCUa/GCGa, cable, or SCUa. In addition, with the Y-shaped cable, switchover between GCUa/GCGa boards does not affect the SCUa boards.
� Transmission port backup
− Unchannelized optical ports support MSP 1:1 or MSP 1+1 redundancy.
− Channelized optical ports support MSP 1:1 backup.
− FE or GE ports support port backup and load sharing between the ports.
All these improve the reliability of transmission. � OM dual planes
To improve the reliability of OM channels, the BSC6810 provides the OM dual planes, including dual OMUa boards, dual Ethernet adapters, and dual main control boards.
� Crystal Aging Compensation technology
The BSC6810 adopts the Huawei-patented Crystal Aging Compensation technology to compensate for frequency deviation caused by the aging of temperature-constant crystal oscillators. This technology protects the clock precision from the influence of the aging of the crystal oscillators and ensures long-term stability and reliability of the system clock.
� Dual –48 V power supplies
The two independent –48 V power supplies operate at the same time to ensure normal operations in case either of them fails. The failed supply can be restored without a power cut. This improves the reliability and availability of the power system.
5.3 Hardware Reliability The BSC6810 adopts the reliability design such as board and port backup and load sharing. In addition, the BSC6810 improves the reliability and maintainability by optimizing the fault detection and isolation techniques for boards and the whole system.
The hardware reliability design of the BSC6810 takes into account the following techniques:
� The system uses the multi-level cascaded and distributed cluster control mode. Several CPUs form a cluster processing system. Each module has distinct functions. The communication channels between modules are based on the backup design or anti-suspension/breakdown design.
� The system uses the redundancy design, as shown in Table 5-1, to support hot swap of boards and backup of important modules. Therefore, the system has great error tolerance.
Table 5-1 Parts redundancy
Part Redundancy Mode
GCUa/GCGa Board redundancy
SCUa Board redundancy + port trunking on GE ports
SPUa Board redundancy
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 45 of 65
Part Redundancy Mode
DPUb Board resource pool
AOUa Board redundancy + MSP 1:1 optical port redundancy
POUa Board redundancy + MSP 1:1 or MSP 1+1 optical port redundancy
UOIa Board redundancy + MSP 1:1 or MSP 1+1 optical port redundancy
FG2a Board redundancy
GOUa Board redundancy
GE port on the FG2a or GOUa
Port redundancy or load sharing
FE port on the FG2a
Port redundancy or load sharing
OMUa Board redundancy
� When an entity fails, the isolation mechanism transfers the services to another entity for processing. After the system finds a faulty board in the resource pool, it isolates the board. Then another board in the resource pool will process the subsequent services.
� When a board with a single function fails, restarting the system might clear the fault.
� All boards support dual-BIOS. Faults at one BIOS do not affect startup or operation of the boards.
� The system uses the non-volatile memory to store important data. � With advanced integrated circuits, the system features high integration, good
technology, and high reliability. � All the parts of the system pass the aging test. The process of hardware
assembly is strictly controlled. These methods ensure the high stability and reliability for long-term operation.
5.4 Software Reliability The error tolerance ability of the software system indicates the software reliability. In other words, the whole system can keep on working in case of software failure. This indicates that the system has self-healing ability. The BSC6810 derives this ability from the following aspects:
� Regular check of key resources
Usage check is provided for various software resources in the system. If a resource is unavailable because of a software error, the unavailability lasts only a short time. The reason is that the check mechanism ensures the release of this resource and the output of logs and alarms.
� Task monitoring
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 46 of 65
During the running of software, the BSC6810 monitors the internal errors of all software and some hardware faults, if any. It then reports the errors and faults to the OM system.
� Load sharing
The FG2a and GOUa boards support inter-board load sharing between ports.
The DPUb boards work in resource pool mode. If a DPUb board is faulty, other DPUb boards in the same subrack take over the services carried on the faulty board.
� Data check
The system is able to perform regular or event-driven check for data consistency and export the related log records and alarms.
� Dual versions
The boards of the BSC6810 have active/standby workspaces. The active workspace stores the current version files, and the standby workspace stores the version files except those in the active workspace.
Switchover between the active and standby workspaces can be performed to upgrade or roll back the RNC version. Therefore, the active and standby workspaces facilitate the upgrade of and rollback for the RNC and greatly reduce the time of service disruption caused by the upgrade.
� Data backup
The BAM data and FAM data can be backed up, so that the reliability and consistency of the data are ensured.
� Storage of operation information
The BSC6810 records the operations that you perform and saves the records in the operation log. You can use the operation log to identify and clear errors or faults caused by operations.
� Flow control
The BSC6810 automatically controls the flows on the Iub, Iur, and Iu interfaces to avoid overload caused by heavy traffic.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 47 of 65
6 Technical Specifications
6.1 About This Chapter This chapter consists of the following sections:
� Performance Specifications � Transmission Port Specifications � GPS Feeder Specifications � Reliability Specifications � Structural Specifications � Electrical Specifications � Power Consumption in Typical Configurations � Clock Precision Specifications � Noise and Safety Compliance � Environmental Protection Specifications � International Protection Specifications � Environmental Requirements
6.2 Performance Specifications Table 6-1 describes the performance specifications for the BSC6810.
Table 6-1 Performance specifications
Item Specification
Maximum number of cabinets 2, that is, 1 RSR and 1 RBR
Maximum number of subracks 6, that is, 1 RSS and 5 RBSs
BHCA 1,360,000 (calculated on the basis of Huawei traffic model)
Maximum voice traffic 51,000 Erlang (calculated on the basis of Huawei traffic model)
PS throughput (UL + DL) 3,264 Mbit/s
Maximum number of NodeBs 1,700
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 48 of 65
Item Specification
Maximum number of cells 5,100
6.3 Transmission Port Specifications Table 6-2 describes the transmission port specifications for the BSC6810.
Table 6-2 Transmission port specifications
Transmission Type
Standard Board or Port Type
Connector Type
Remarks
AEUa DB44 The AEUa provides 32 E1s/T1s for ATM transport on the Iub interface.
E1/T1 ITU-T G.703/G.704
PEUa DB44 The PEUa provides 32 E1s/T1s for IP transport on the Iub interface.
AOUa LC/PC The AOUa provides 2 channelized STM-1/OC-3 optical ports for ATM transport on the Iub interface. Channelized
STM-1/OC-3
� ITU-T G.957 � ITU-T I.432.1 � ITU-T I.432.2
POUa LC/PC The POUa provides 2 channelized STM-1/OC-3 optical ports for IP transport on the Iub interface.
The UOIa provides 4 unchannelized STM-1/OC-3c optical ports for ATM transport on the Iub, Iur, and Iu interfaces. Unchannelized
STM-1/OC-3c
� ITU-T G.957 � ITU-T I.432.1 � ITU-T I.432.2
UOIa LC/PC The UOIa provides 4 unchannelized STM-1/OC-3c optical ports for IP transport on the Iub, Iur, and Iu interfaces.
FE IEEE 802.3 FE port on the FG2a RJ45
The FG2a provides 8 FE ports for IP transport on the Iub, Iur, and Iu interfaces.
GE electrical port on the FG2a
RJ45 The FG2a provides 2 GE electrical ports for IP transport on the Iub, Iur, and Iu interfaces.
GE IEEE 802.3 GE optical port on the GOUa
LC/PC The GOUa provides 2 GE optical ports for IP transport on the Iub, Iur, and Iu interfaces.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 49 of 65
The maximum transmission distances of different port types are as follows:
� E1/T1 port: 500 m
� STM-1 port: 15 km
� FE port: 100 m
� GE electrical port on the FG2a: 100 m
� GE optical port on the GOUa: 10 km
6.4 GPS Feeder Specifications The BSC6810 provides GPS feeders that meet the following specifications:
� Length of the GPS feeder � 100 m
� 100 m < length of the GPS feeder � 300 m
� 300 m < length of the GPS feeder � 500 m
6.5 Reliability Specifications Table 6-3 describes the reliability specifications for the BSC6810.
Table 6-3 Reliability specifications
Item Specification
System inherent availability ƒ 99.999%
Mean Time Between Failures (MTBF) ƒ 347,700 h
System restarting time � 10 min
Mean Time To Repair (MTTR) � 1 h
6.6 Structural Specifications Table 6-4 describes the structural specifications for the BSC6810.
Table 6-4 Structural specifications
Item Specification
Cabinet standard The structural design conforms to the IEC60297 standard and IEEE standard.
Dimensions of a cabinet � N68E-22 cabinet: 2,200 mm (height) x 600 mm
(width) x 800 mm (depth) � N68-21-N cabinet: 2,133 mm (height) x 600 mm
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 50 of 65
Item Specification
(width) x 800 mm (depth)
Height of the available space in a cabinet
� N68E-22 cabinet: 46 U � N68-21-N cabinet: 44 U
Weight of a single cabinet � N68E-22 cabinet: � 350 kg � N68-21-N cabinet: � 410 kg
Load bearing capacity of the equipment room ƒ 450 kg/m2
6.7 Electrical Specifications Table 6-5 describes the electrical specifications for the BSC6810.
Table 6-5 Electrical specifications
Item Specification
Power supply � –48 V DC power � Input voltage range: –40 V to –57 V
Electromagnetic Compatibility (EMC) Meets the requirements in ETSI EN300 386 and Council directive 89/336/EEC
RSS power consumption � 1,530 W
RBS power consumption � 1,540 W
Power consumption of the RSR in full configuration � 4,650 W
Power consumption of the RBR in full configuration � 4,660 W
6.8 Power Consumption in Typical Configurations Table 6-6 describes the specifications for power consumption of the BSC6810 in typical configurations.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 51 of 65
Table 6-6 Power consumption of the BSC6810 in typical configurations
Number of Subracks
Iu/Iur/Iub ATM Optical Transport with Ports in Redundancy
Iu/Iur/Iub GE Optical Transport with Ports Not in Redundancy
Voice Traffic (Erlang)
(UL + DL) PS Throughput (Mbit/s)
Number of Cells
1 RSS � 1,570 W � 1,260 W 6,000 384 600
1 RSS + 1 RBS � 3,110 W � 2,400 W 15,000 960 1,500
1 RSS + 2 RBSs � 4,650 W � 3,540 W 24,000 1,536 2,400
1 RSS + 3 RBSs � 6,230 W � 4,720 W 33,000 2,112 3,300
1 RSS + 4 RBSs � 7,770 W � 5,860 W 42,000 2,688 4,200
1 RSS + 5 RBSs � 9,310 W � 7,000 W 51,000 3,264 5,100
6.9 Clock Precision Specifications The precision of the clock for the BSC6810 meets the associated requirements of the stratum 3 clock.
6.10 Noise and Safety Compliance Table 6-7 describes the noise and safety compliance for the BSC6810.
Table 6-7 Noise and safety compliance
Item Specification
Noise < 72 dB; fulfilling the requirements in EUROPEAN ETS 300 753
Safety
Fulfilling the requirements in: � IEC 60950 � EN 60950 � UL60950 � IEC 60825-1 � IEC 60825-2 � AS/NZS 60950-1 � GB4943-2001
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 52 of 65
6.11 Environmental Protection Specifications The environmental protection specifications for the BSC6810 are as follows:
� RoHS: Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
� WEEE: The EU Directive on Waste of Electrical and Electronic Equipment
6.12 International Protection Specifications The BSC6810 reaches the protection degree of IP50.
6.13 Environmental Requirements The storage, transportation, and working environments of the BSC6810 conform to the following standards:
� GB2423.1-1989 � GB2423.2-1989 � GB2423.4-1993 � GB2423.22-1987 � GB/T13543 � ETS 300 019 � NEBS GR-63-core
6.13.1 Storage Environment The BSC6810 has storage requirements for climate, waterproofing conditions, biological environment, air purity, and mechanical stress.
Climatic Requirements
Table 6-8 describes the climatic requirements for storing the BSC6810.
Table 6-8 Climatic requirements for storing the BSC6810
Item Specification
Temperature –40°C to +70°C
Temperature change rate � 1°C/min
Relative humidity 10% to 100% RH
Altitude � 5,000 m
Air pressure 70 kPa to 106 kPa
Solar radiation � 1,120 W/m²
Thermal radiation � 600 W/m²
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 53 of 65
Item Specification
Wind speed � 30 m/s
Waterproofing Requirements
The waterproofing requirements for storing the BSC6810 are as follows:
� The equipment is usually stored in a room. � There is no water on the floor or any water entering the package. � In the equipment room, there is no water that may damage the equipment, such
as water from automatic fire protection devices or the air conditioner.
If the equipment has to be placed outdoors, ensure that:
� The package is intact. � Waterproofing measures are taken to prevent rainwater from entering the
package. � There is no water on the ground or any water entering the package. � The package is not exposed to direct sunlight.
Biological Requirements
The biological requirements for storing the BSC6810 are as follows:
� No fungus or mildew may grow in the equipment room or near the equipment. � The place is free from rodents, such as rats.
Air Purity Requirements
The air purity requirements for storing the BSC6810 are as follows:
� The air is free from explosive, conductive, magnetically conductive, or corrosive dust.
� The density of physically active materials must meet the requirements listed in Table 6-9.
� The density of chemically active materials must meet the requirements listed in Table 6-10.
Table 6-9 Storage requirements for physically active materials
Physically Active Material Unit Density
Suspended dust mg/m³ � 5.00
Falling dust mg/m²·h � 20.0
Sand mg/m³ � 300
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 54 of 65
Physically Active Material Unit Density
Note: � Suspended dust: diameter � 75 µm
� Falling dust: 75 µm � diameter � 150 µm
� Sand: 150 µm � diameter � 1,000 µm
Table 6-10 Storage requirements for physically active materials
Chemically Active Material Unit Density
SO2 mg/m³ � 0.30
H2S mg/m³ � 0.10
NO2 mg/m³ � 0.50
NH3 mg/m³ � 1.00
Cl2 mg/m³ � 0.10
HCl mg/m³ � 0.10
HF mg/m³ � 0.01
O3 mg/m³ � 0.05
Mechanical Stress Requirements
Table 6-11 describes the mechanical stress requirements for storing the BSC6810.
Table 6-11 Mechanical stress requirements for storing the BSC6810
Item Sub-item Specification
Offset � 7.0 mm –
Accelerated speed – � 20.0 m/s² Sinusoidal vibration
Frequency range 2 Hz to 9 Hz 9 Hz to 200 Hz
Impact response spectrum II � 250 m/s²
Unsteady impact
Static payload � 5 kPa
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 55 of 65
Item Sub-item Specification
Note: � Impact response spectrum: maximum acceleration response curve generated by the
equipment under specified impact excitation Impact response spectrum II means that the duration of semi-sine impact response spectrum is 6 ms.
� Static payload: capability of the equipment in package to bear the pressure from the top in normal pile-up method
6.13.2 Transportation Environment The BSC6810 has transportation requirements for climate, waterproofing conditions, biological environment, air purity, and mechanical stress.
Climatic Requirements
Table 6-12 describes the climatic requirements for transporting the BSC6810.
Table 6-12 Climatic requirements for transporting the BSC6810
Item Specification
Temperature –40°C to +70°C
Temperature change rate � 3°C/min
Relative humidity 5% to 100% RH
Altitude � 5,000 m
Air pressure 70 kPa to 106 kPa
Solar radiation � 1,120 W/ m²
Thermal radiation � 600 W/ m²
Wind speed � 30 m/s
Waterproofing Requirements
The waterproofing requirements for transporting the BSC6810 are as follows:
� The package is intact. � Waterproofing measures are taken to prevent rainwater from entering the
package. � The inside of the vehicle is completely dry.
Biological Requirements
The biological requirements for transporting the BSC6810 are as follows:
� No fungus or mildew may grow in the vehicle.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 56 of 65
� The place is free from rodents, such as rats.
Air Purity Requirements
The air purity requirements for transporting the BSC6810 are as follows:
� The air is free from explosive, conductive, magnetically conductive, or corrosive dust.
� The density of physically active materials must meet the requirements listed in Table 6-13.
� The density of chemically active materials must meet the requirements listed in Table 6-14.
Table 6-13 Transportation requirements for physically active materials
Physically Active Material Unit Density
Suspended dust mg/m³ No requirement
Falling dust mg/m²·h � 3.0
Sand mg/m³ � 100
Note: � Suspended dust: diameter � 75 µm � Falling dust: 75 µm � diameter � 150 µm � Sand: 150 µm � diameter � 1,000 µm
Table 6-14 Transportation requirements for chemically active materials
Chemically Active Material Unit Density
SO2 mg/m³ � 0.30
H2S mg/m³ � 0.10
NO2 mg/m³ � 0.50
NH3 mg/m³ � 1.00
Cl2 mg/m³ � 0.10
HCl mg/m³ � 0.10
HF mg/m³ � 0.01
O3 mg/m³ � 0.05
Mechanical Stress Requirements
Table 6-15 describes the mechanical stress requirements for transporting the BSC6810.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 57 of 65
Table 6-15 Mechanical stress requirements for transporting the BSC6810
Item Sub-item Specification
Offset � 7.5 mm – –
Accelerated speed – � 20.0 m/s² � 40.0 m/s² Sinusoidal vibration
Frequency range 2 Hz to 9 Hz 9 Hz to 200 Hz
200 Hz to 500 Hz
Spectrum density of accelerated speed
10 m²/s³ 3 m²/s³ 1 m²/s³ Random vibration
Frequency range 2 Hz to 9 Hz 9 Hz to 200 Hz
200 Hz to 500 Hz
Impact response spectrum II � 300 m/s² Unsteady
impact Static payload � 10 kPa
Note: � Impact response spectrum: maximum acceleration response curve generated by the
equipment under specified impact excitation Impact response spectrum II means that the duration of semi-sine impact response spectrum is 6 ms.
� Static payload: capability of the equipment in package to bear the pressure from the top in normal pile-up method
6.13.3 Working Environment The BSC6810 has working environment requirements for climate, biological environment, air purity, and mechanical stress.
Climatic Requirements
Table 6-16 and Table 6-17 describe the climatic requirements for operating the BSC6810.
Table 6-16 Temperature and humidity requirements for operating the BSC6810
Temperature Relative Humidity
Normal Safe Normal Safe
0°C to 45°C –5°C to +55°C 5% to 85% RH 5% to 95% RH
Note: � The values are measured 1.5 m above the floor and 0.4 m in front of the equipment, without
protective panels in front of or behind the cabinet. � Safe refers to continuous operation for not more than 96 hours or accumulated operation for
not more than 15 days in a year.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 58 of 65
Table 6-17 Other climatic requirements for operating the BSC6810
Item Specification
Altitude � 4,000 m
Air pressure 70 kPa to 106 kPa
Temperature change rate � 3°C/min
Solar radiation � 700 W/m²
Thermal radiation � 600 W/m²
Wind speed � 5 m/s
Biological Requirements
The biological requirements for operating the BSC6810 are as follows:
� No fungus or mildew may grow in the area where the equipment is operated. � The place is free from rodents, such as rats.
Air Purity Requirements
The air purity requirements for operating the BSC6810 are as follows:
� The air is free from explosive, conductive, magnetically conductive, or corrosive dust.
� The density of physically active materials must meet the requirements listed in Table 6-18.
� The density of chemically active materials must meet the requirements listed in Table 6-19.
Table 6-18 Working environment requirements for physically active materials
Physically Active Material Unit Density
Dust particles Particles/m³ � 3 x 104
(no visible dust on the desktop within three days)
Note: Dust particles: diameter ƒ 5 µm
Table 6-19 Working environment requirements for chemically active materials
Chemically Active Material Unit Density
SO2 mg/m³ � 0.20
H2S mg/m³ � 0.006
NH3 mg/m³ � 0.05
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 59 of 65
Chemically Active Material Unit Density
Cl2 mg/m³ � 0.01
Mechanical Stress Requirements
Table 6-20 describes the mechanical stress requirements for operating the BSC6810.
Table 6-20 Mechanical stress requirements for operating the BSC6810
Item Sub-item Specification
Offset � 3.5mm –
Accelerated speed – � 10.0 m/s² Sinusoidal vibration
Frequency range 2 Hz to 9 Hz 9 Hz to 200 Hz
Impact response spectrum II � 100 m/s²
Unsteady impact
Static payload 0
Note: � Impact response spectrum: maximum acceleration response curve generated by the
equipment under specified impact excitation Impact response spectrum II means that the duration of semi-sine impact response spectrum is 6 ms.
� Static payload: capability of the equipment in package to bear the pressure from the top in normal pile-up method
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 60 of 65
7 Installation
7.1 About This Chapter This chapter consists of the following sections:
� Hardware Installation � Software Installation
7.2 Hardware Installation During hardware installation, adhere to the following principles:
� The height of the equipment room is not less than 3,000 mm. The height refers to the distance between the lowest level of the ceiling and the highest position of the floor.
� The aisle between two rows of cabinets is at least 1,000 mm wide. � The distance between the wall and the side/front/back of a cabinet that is closest
to the wall is not less than 800 mm. � An aisle of at least 1,000 mm in width is reserved in the equipment room.
Do not install the cabinet against the wall.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 61 of 65
Figure 7-1 shows the equipment room floor plan.
Figure 7-1 Equipment room floor plan (unit: mm)
≥ 800
≥ 800
≥ 800
≥ 1000 ≥ 800
� The BSC6810 supports both overhead and underfloor cabling.
� The BSC6810 supports both front and back maintenance.
� The BSC6810 does not support back-to-back installation of cabinets. Interconnect the cabinets side by side if necessary.
For details about the environmental requirements of the BSC6810, refer to section 6.13 "Environmental Requirements."
7.3 Software Installation The software can be easily installed on the engineering site. Before delivery, plenty of internal data is automatically generated or configured. You need to install only the BAM software and LMT software during either initial installation or upgrade.
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 62 of 65
A Acronyms and Abbreviations
2G The Second Generation
3G The Third Generation
3GPP Third Generation Partnership Project
AAL2 ATM Adaptation Layer type 2
AAL5 ATM Adaptation Layer type 5
AMR Adaptive Multi Rate
ARP Address Resolution Protocol
ATM Asynchronous Transfer Mode
BAM Back Administration Module
BE Best Effort
BER Bit Error Rate
BFD Bidirectional Forwarding Detection
BHCA Busy Hour Call Attempt
BIOS Basic Input Output System
BITS Building Integrated Timing Supply System
BLER Block Error Rate
BOOTP Bootstrap Protocol
CAC Call Admission Control
CBC Cell Broadcast Center
CC Continuous Check
CCP Communication Control Port
CDT Call Data Tracing
CN Core Network
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 63 of 65
CPU Central Processing Unit
CS Circuit Switched
DC Direct Current
DCH Dedicated Channel
DHCP Dynamic Host Configuration Protocol
DL Downlink
DSP Digital Signal Processor
E-DCH Enhanced Dedicated Channel
EMC Electromagnetic Compatibility
EMS Element Management System
ETS European Telecommunication Standard
ETSI European Telecommunications Standards Institute
FAM Front Administration Module
FE Fast Ethernet
FP Frame Protocol
FP MUX Frame Protocol Multiplexing
FTP File Transfer Protocol
GBR Guaranteed Bit Rate
GE Gigabit Ethernet
GPRS General Packet Radio Service
GPS Global Positioning System
GTP-U GPRS Tunneling Protocol for User Plane
GUI Graphic User Interface
HSDPA High Speed Downlink Packet Access
HS-DSCH High Speed Downlink Shared Channel
HSUPA High Speed Uplink Packet Access
IEEE Institute of Electrical and Electronics Engineers
IMA Inverse Multiplexing on ATM
IMS IP Multimedia Subsystem
IP Internet Protocol
IPC Inter-Process Communication
IPoA Internet Protocols over ATM
ITU-T International Telecommunication Union - Telecommunication
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 64 of 65
Standardization Sector
KPI Key Performance Indicator
LAN Local Area Network
LED Light Emitting Diode
LMT Local Maintenance Terminal
MAC Medium Access Control
MBMS Multimedia Broadcast and Multicast Service
MDC Macro Diversity Combining
MGW Media Gateway
MLPPP Multilink PPP
MML Man Machine Language
MSC Mobile Switching Center
MSP Multiplex Section Protection
MTBF Mean Time Between Failures
MTP3-b Message Transfer Part level 3 - broadband
MTTR Mean Time To Repair
NBAP NodeB Application Protocol
NCP NodeB Control Port
NE Network Element
NMS Network Management System
OM Operation and Maintenance
PARC Platform of Advanced Radio Controller
P-CPICH Primary Common Pilot Channel
PDCP Packet Data Convergence Protocol
PPP Point-to-Point Protocol
PS Packet Switched
PVC Permanent Virtual Channel
QoS Quality of Service
RANAP Radio Access Network Application Part
RBR RNC Business Rack
RBS RNC Business Subrack
RFN RNC Frame Number
RLC Radio Link Control
RNC V200R010
Product Description
Issue 02 (2008-03-30) Commercial in Confidence Page 65 of 65
RNC Radio Network Controller
RNSAP Radio Network Subsystem Application Part
RRC Radio Resource Control
RRM Radio Resource Management
RSR RNC Switching Rack
RSS RNC Switching Subrack
RTWP Received Total Wideband Power
RX Receiver/Reception/Receive
SAAL Signaling ATM Adaptation Layer
SABP Service Area Broadcast Protocol
SCTP Stream Control Transmission Protocol
SDH Synchronous Digital Hierarchy
SGSN Serving GPRS Support Node
SIR Signal-to-Interference Ratio
SNR Signal-to-Noise Ratio
SRNS Serving Radio Network System
SS7 Signaling System Number 7
SSL Security Socket Protocol
STM-1 Synchronous Transport Mode-1
TDM Time Division Multiplexing
TX Transmitter/Transmit
UDP User Datagram Protocol
UE User Equipment
UL Uplink
UMTS Universal Mobile Telecommunications System
UTRAN Universal Terrestrial Radio Access Network
VCL Virtual Connect Link
VLAN Virtual Local Area Network
VoIP Voice over IP
VPN Virtual Private Network
WCDMA Wideband Code Division Multiple Access