Ribbon Hari Bows
-
Upload
holly-clark -
Category
Documents
-
view
226 -
download
0
Transcript of Ribbon Hari Bows
8/6/2019 Ribbon Hari Bows
http://slidepdf.com/reader/full/ribbon-hari-bows 1/2
RIBBO
Give Me
An easy, ho5 designer h
{
The Corker Bow
4. Criss-cross the cut curls (as shown) and secure
in the center with thread.
5. Glue bow to hair clip. Trim curls as needed, and
u bow.
1. Tightly wrap
ribbon around
dowel rods
and secure
with clamps at
both ends.
SUPPLY LIST
Assorted ribbons, narrow-width
Fabric stiener
Three 1/4˝ dowel rods
Needle and Thread
3. Make loops as
shown with other 30˝
length o 3/8˝ and 5/8˝
ribbon, placing one
ribbon atop the other.
Form a cloverlea shape
and make sure loops
are even, then hot glue
ribbon layers together.
4. With a 29˝
length o 1 ½˝
wide ribbon, make
a narrow Figure 8.
Bring in the ends,
weave the needle
through and cinchtogether. Wrap
thread around and tie o.
5. Place the wider
7” ribbon on
bottom, then make
an “X” on top with
the two narrow
7˝ ribbons. Tack
together in center.
6. Layer the ribbons
and arrange as
desired on top o the
ribbon spray. Wrap a
French knot around all
the layers and glue in
back. Attach hair clip.
Trim ends and apply
Fray Check.
1. Using a 30˝ length o 1 ½˝ wide
ribbon, make a wide fgure 8.
2. Bring ends o loop
to center, as shown,
and weave needle and
thread through center
and cinch together.
Wrap thread around
center and tie o in
back o bow.
www.hobbylobby.com www.getinspire dbyhl.com Fabric - 357814
©2010 Hobby Lobby® - The information in these instructions is presented in good faith, but no warranty is given, nor results guaranteed, nor is freedom from any patent to be inferred. Since we have no control over physical conditions surrounding the application of information herein contained, Hobby Lobby Stores, Inc.
disclaims any liability for untoward results. Follow manufacturer’s instructions in using paints and other materials, keeping them out of reach of children,since some may be toxic, or otherwise cause injury. Photography by Sanford Mauldin.
The Four-Layer Loopy BowSUPPLY LIST
Two lengths of 3/8˝ wide ribbon, each 30˝ long
Two lengths of 5/8˝ ribbon for spray, each 7˝ long
Length of 1 ½˝ wide ribbon, 30˝ long
Length of 1 ½˝ wide ribbon, 29˝ long
One length of 5/8˝ ribbon, 30˝ long
One length of 7/8˝ ribbon for spray, 7˝ long
Hair clip
Fray Check
Needle and thread
Scissors
Hot glue gun
2. Using paintbrush, apply abric stiener and
thoroughly coat ribbon. Let dry overnight.
3. Once dry, gently remove ribbon rom the dowel
rods and cut to desired length. Ours were 6˝ long.
Hair clip
Binder clips
Paintbrush
Scissors
Hot glue gun
8/6/2019 Ribbon Hari Bows
http://slidepdf.com/reader/full/ribbon-hari-bows 2/2
The Pinwheel
SUPPLY LIST
Ribbon (approximately 2 yards)
Hair clip
Jewelry wire (approximately 9˝)
Fray Check
Adhesive tape runner
Scissors
Hot glue gun
5. Wrap French knot around center and glue in
back. Adhere hair clip to back. Trim ends and apply
Fray Check.
2. Loop
ribbon length
around hand
with ends
pointing in
opposite
directions,
as shown.
3. Lay at, taking care not to move loops.
Pinch the center o loops to create a gather.
4. Wrap gathered center with jewelry wire to
secure loops.
5. To create rench knot, see steps 6-8 o
Three-Tiered Bow.
6. Hot glue knot in center, covering the wire, and
wrap ends to back. Also secure hair clip to the back
of bow with glue.
1. Cut o a 10˝ length o ribbon and set aside. Cut
remaining ribbon in hal, then adhere these two
pieces back to back. Trim ends with a “V” shape
and apply Fray Check.
The Triple Stack
SUPPPLY LIST
Three dierent patterns o ribbon,
approximately 1 ½˝ wide each
Xyron®
Hair Clip
Fray Check
Needle and thread
Scissors
Hot glue gun
2. For each pattern o ribbon, make a Figure
8 as shown, leaving 2˝ o ribbon ree on
one end.
1. To apply adhesive to back o ribbon, cut two
pieces rom each ribbon pattern each 19˝ long.
Run one 19˝ piece through the Xyron®, then
adhere to the matching length.
3. Careully pinch center and weave needle and thread
in and out o the layers to secure the loops.
4. Repeat Steps 2 and 3 with other two
ribbon patterns. Stack ribbon layers as
desired and tack together.
2. Repeat, making
needle and thread
shown, to secure
4. Stack each
tier, sewing
middle tier to
bottom tier,
then top tier
to middle to
secure.
6. To make the Fr
a piece o ribbon
10˝ long and loop
SUPPPLY LIST
1˝ wide satin r
½” wide satin
1˝ wide grosgr
Hair clip
The Thr
1. For the bottom
ribbons 32˝ long.
side out, and mak