RFA19354 Kitchen Manual

17
Revit Content ® Copyright 2010 -2011 by Aplo Limited, All Rights reserved RFA 19354 Kitchen PLAN FRONT ELEVATION 3D VIEW Page 1 of 17

Transcript of RFA19354 Kitchen Manual

Page 1: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 1/17

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

PLAN

FRONT ELEVATION

3D VIEW

Page 1 of 17

Page 2: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 2/17

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

How To Create Drawers

In the Type P arameters under:-

Graphics

The tick boxes that need to be selected are:-UNIT HEIGHT LOCK, SHELL VISIBILITY, TOP VISIBILITY & JUST DRAWERS The result is shown in Fig 1A choice to have the Drawers in the the outerframe flushed or the exterior o f the outerframe just by selecting thePANEL BETWEEN 

Dimensions

Adjust the Height to 900mm And the Width to1000mmYou can specify and control the Drawers & The Drawer Handle.The Parameters which can be adjusted to change the Drawers are :-DRAW COUNT which adjust the amount of draws you may want to specifyDRAW HEIGHT, DRAW HANDLE OFFSET FROM TOP, DRAW HANDLE HEIGHT, DRAW HANDLE WIDTH & DRAW HANDLE HEIGHT 

(PLEASE REFER TO DIMENSIONS OVERVIEW ) 

No Drawers

For no Drawers set DRAW COUNT to zero.

How To Create Floor UnitDouble & Single

In the Type Parameters under:-

Graphics

The tick boxes that need to be selected are:-UNIT HEIGHT LOCK, SHELL VISIBILITY, TOP VISIBILITY, DOORS V ISIBILITY, DOOR HANDLE VISIBILITY & DOUBLE SWING The result is shown in Fig 2A choice to have the Doors in the the o uterframe flushed or the exterior of the outerframe just by s electing the

PANEL BETWEEN 

If the Tick Box DOUBLE SWING is:-selected,The Result is shown as a Double Swing Unitunselected, The Result is shown as a Single Swing Unit

Dimensions

You can specify and co ntrol the Door & The Door Handle.The Parameters which can be adjusted to change the Doors are :-WIDTH which adjust the panel widths when its a double or a si ngle cupboard.DOOR HANDLE OFFSET FROM TOP, DOOR HANDLE OFFSET FROM SIDE, DOOR HANDLE DEPTH,DOOR HANDLE WIDTH & DOOR HANDLE HEIGHT To Open & Close the doors, both doo rs have a swing parameter which are:-DOOR OPENING LEFT & SINGLE% & DOOR OPENING RIGHT%.

This parameter DOOR OPENING LEFT & SINGLE% is for the left door. When you untick DOUBLE SWING the result is aLeft single swing door which this p arameter is used for. To create a Right single swing door,there is a flip controlswitch as shown In plan. This will flip the cupbourd to give a result of a Right single swing door which the sameparameter is used to open and close the swing door.

(PLEASE REFER TO DIMENSIONS OVERVIEW ) 

How To Create FloorOven & Cooker Unit

FIG 2

FIG 3

FIG 1

In the Type Parameters under:-

Graphics

The tick boxes that need to be selected are:-UNIT HEIGHT LOCK, SHELL VISIBILITY, DOORS VISIBILITY, TOP VISIBILITY, COOKER VISIBILITY & OVEN VISIBILITY The result is shown in Fig 3A choice to have the Oven Door in the the outerframe flushed or the exterior of the outerframe just by selecting thePANEL BETWEEN 

If the Tick Box COOKER & OVEN is:-selected,The Result is shown as Fig 3If Tick boxes are unselected, The Result is shown asPlain Worktop with no doors & Drawers

Dimensions

The Parameters which can be adjusted to change the Cooker are :-COOKER WIDTH, COOKER DEPTH,COOKER BURNER THICKNESS,COOKER OFFSET,COOKER BURNER OFFSET FROM SIDE, COOKER BURNER F RONT & BACK OFFSET,COOKER BURNER WIDTH, COOKER BURNER DEPTH & COOKER BURNER RADIUS All these parameters adjust properly when its a double unit.The Oven Unit adjusts with the Width & Height and w ith theDRAW COUNT as shown in Fig 3

The Results of changing the values of these parameters are shown onPage 10 of 14 from Fig 11 to 16

(PLEASE REFER TO DIMENSIONS OVERVIEW ) 

Page 2 of 17

FIG 4

How To Create Floor Sink UnitIn the Type Parameters under:-

Graphics

The tick boxes that need to be selected are:-UNIT HEIGHT LOCK, SHELL VISIBILITY, TOP VISIBILITY, DOORS VISIBILITY,DRAINER VISIBILITY, SINK VISIBILITY SINK 2 VISIBILITY The result is shown in Fig 4

Dimensions

Adjust the Height to 900mm And the Width to1000mmThe Parameters which can be adjusted to change the Sink & Sink 2 are :-SINK HEIGHT,SINK DEPTH, SINK WIDTH,SINK RADIUS,SINK SHELL THICKNESS,SINK POSITION FROM THE MIDDLE & SINK FRONT & BACK OFFSET 

SINK 2 HEIGHT,SINK 2 DEPTH, SINK 2 WI DTH,SINK 2 RADIUS,SINK SHELL THICKNESS, SINK POSITION FROM SINK 

SINK DRAINER LEFT OFFSET,SINK DRAINER RIGHT OFFSET,SINK DRAINER FRONT OFFSET & SINK DRAINER BACK OFFSET 

SINK TAP HEIGHT,SINK TAP LENGTH,SINK TAP LENGTH 2, SINK TAP RADIUS SINK TAP PROFILE WIDTH, SINK TAP PROFILE LENGTH, SINK TAP PROFILE RADIUS SINK TAP POSITION FROM BACK, SINK TAP POSITION FROM SIDE 

SINK TAP KNOB WIDTH, SINK TAP KNOB DEPTH,SINK TAP KNOB RADIUS, SINK TAP KNOB HEIGHT (PLEASE REFER TO DIMENSIONS OVERVIEW ) 

The Results of changing the values of these parameters are shown onPage 11 of 14 from Fig 17 to 21

(PLEASE REFER TO DIMENSIONS OVERVIEW ) 

Page 3: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 3/17

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

How To Create Wall HungDouble & Single Unit

FIG 5

In the Type Parameters under:-

Graphics

To Create the Wall hung units, The process is the sa me as creating the floor units as described on page 1 - 5under How To Create Floor Unit Double & Single. The parameter that needs to be adjusted is WALL UNIT HEIGHT which controls & switches thevisibility on of all profiles,as shown in Fig 5

Dimensions

All parameters which are used to control the floor unit cupboard as described on page 1 o f 5 are also used forthe wall hung unit.The additional Parameters which can be adjusted to change theWall Unit are :-

WALL UNIT HEIGHT, WALL UNIT BOTTOM THICKNESS, WALL UNIT FRONT BOTTOM LENGTH & WALL UNT FRONT THICKNESS 

(PLEASE REFER TO DIMENSIONS OVERVIEW ) 

.

Page 3 of 17

FIG 6

How To CreateCorner Unit

In the Type Parameters under:-

Graphics

To Create a Corner Unit, The process is the same as creating the floor units as described on page 1 - 5 under How To Create Floor Unit Double & Single. The parameter that needs to be adjusted is CORNER UNIT VISIBILITY which controls & switches thevisibility on of the Corner Unit & all profiles,as shown in Fig 6

Dimensions

All parameters which are used to control the floor unit cupboard as described on page 1 of 5 under How To CreateFloor Unit are also used for the Corner UnitThe additional Parameters which can be adjusted to change the are :-

CORNER UNIT WIDTH 

(PLEASE REFER TO DIMENSIONS OVERVIEW ) 

How To Create Legs

In the Type Parameters under:-

Graphics

To Create Legs, adjust the parameter LEGS VISIBILITY on which controls & switchesthe visibility on of the Legs as shown inFig 7

LEGS VISIBILITY is a Integer visibility parameter for each leg, so each number willswitch on the visibility as shown in Fig 7If the LEGS VISIBILITY is on integer 7, then all legs w ill appearIf the LEGS VISIBILITY is on integer 0, then all legs will switch off and the result will be Fig 7

NOTELEGS VISIBILITY Integers 5 & 6 will only switch on whenCORNER UNIT VISIBILTY is switched on.LEGS VISIBILITY Integer 7 will switch on the four legs for a normal unit.

Dimensions

The parameters which controls the Leg Height Is Bottom Base HeightThe additional Parameters which can be adjusted to change the legs are :-

LEG RADIUS, LEG LENGTH, LEG WIDTH LEG POSITION LEFT & RIGHT & LEG POSITION FRONT & BACK 

(PLEASE REFER TO DIMENSIONS OVERVIEW ) 

1

2

3

4

5

FIG 7

6

How To Create Back SplashIn the Type Parameters under:-

Graphics

To Create Backsplash on w orktop adjust the parameter BACKSPLASH VISIBILITY as shown inImage C on Page 9 - 9

Dimensions

The parameters which controls the BACKSPLASH is:-

BACK SPLASH HEIGHT & BACKSPLASH THICKNESS 

(PLEASE REFER TO DIMENSIONS OVERVIEW ) 

Page 4: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 4/17

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

Page 4 of 17

How To Create Shelves & DividersThe Parameters are:-

A Left Divider, A Left Divider Distance, A Left Divider Height Offset &A Left Divider Height

A Right Divider, A Right Divider Distance, A Right Divider Height Offset &A Right Divider Height

Shelves Offset From Bottom, Shelves Offset From Shelve,Shelves Count Shelve Width

Shelves and Dividers parameters are found in the Dimensions and can be adjusted almost in everyway

There are 2 Dividers, 1 o n the Left & 1 o n the RightThese Dividers have a Distance from the Left & Right and also have a Height and Height Offset

NOTE

All Dividers & Shelves have a Visibility when all dimension are 0 thenDividers & Shelves will switch off visibility

(PLEASE REFER TO DIMENSIONS OVERVIEW ) 

How To Create Fix PanelIn the Type Parameters under:-

Graphics

To Create Symbol Lines adjust the parameter FIX PANEL the result will beFig 8

To adjust the offset of the fix panel, the parameter is called FIX PANEL. the result will be shown as Fig 8. Thisadjustment only works when it is a single door unit. This setup is ideal if you have a small kitchen setup, and onthe return wall there is a diffrent setup configuration of a corner unit. The Dimension Parameter that isadjusted is FIX PANEL OFFSET 

FIG 9

FIG 10

How To Create an Extractor FanIn the Type Parameters under:-

Graphics

To Create an extractor fan adjust the parameter EXTRACTOR FAN  the result will beFig 9

DimensionsThe Additional parameters that need to be adjusted areEXTRACTOR HOOD BOTTOM WIDTH,EXTRACTOR HOOD BOTTOM DEPTH,EXTRACTOR HOOD BOTTOM HEIGHT,EXTRACTOR HOOD MIDDLE BOTTOM SIDE OFFSET EXTRACTOR HOOD MIDDLE TOP FRONT OFFSET,EXTRACTOR HOOD MIDDLE TOP BACK OFFSET,EXTRACTOR HOOD MIDDLE TOP RIGHT OFFSET, EXTRACTOR HOOD MIDDLE LEFT FRONT OFFSET,EXTRACTOR HOOD TOP HEIGHT,EXTRACTOR HOOD TOP W IDTH,EXTRACTOR HOOD TOP DEPTH & EXTRACTOR HOOD RADIUS 

The Results of changing the values of these parameters are shown onPage 14 of 14 from Fig 30 to 35

(PLEASE REFER TO DIMENSIONS OVERVIEW ) 

FIG 8

How To Create Drawers on Top or BottomIn the Type Parameters under:-

Graphics

To Create swap of Drawers & Doors adjust the parameter DRAWERS ON BOTTOM  the result will be Fig 10

If Selected the Drawers will be place on the bottom of the DoorsIf Unselected the Drawers will be placed on top of the Doors

It is very easy to setup a combination of Door and Drawers with changing just a few Parameters. You can changebetween a single and double doors with s electingDOUBLE SWING and choose the number of Drawers by adjusting

 just one Parameter DRAW COUNT . To swap the position of the Door and the Drawers, just by selecting Drawers OnBottom.

The the Height of the Kitchen Unit is automatically adjusted by the number of drawers with the parameter DRAW COUNT and the DRAW HEIGHT .

If you do not want the Draw count & Draw Height to determine the Height of the unit simple select the parameterunder Graphic, UNIT HEIGHT LOCK This lets you lo ck the Height of the Kitchen Unit which results in the automatic adjustments of the DrawersHeights within the set height as shown in Fig 10

(PLEASE REFER TO DIMENSIONS OVERVIEW ) 

How To Create Symbol LinesIn the Type Parameters under:-

Graphics

To Create Symbol Lines adjust the parameter SHOW SYMBOL LINES  the result will beFig 8

To Have localised symbol lines, having the symbol lines showing the opposite side showing in Elevationadjust the parameter SHOW SYMBOL LINES FROM HINGE SIDE  the result will be a change fromFig 8

FIX PANEL

Page 5: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 5/17

SinkWidth

   S   i   n   k

    R   a    d   i   u   s

   D   o   o   r

   O   p   e   n   i   n   g

   L   e   f  t   &

   S   i   n   g   l   e

    %

  D  o  o

  r   O  p  e

  n  i  n  g

   R  i  g   h  t

SymbolLines

ReferenceLines

Sinkk2Width

Sink2PosionF

rom

Sink

   S    i   n    k    k

    2     R   a   d    i   u

  s

  S i  n  k  k  2   D  e  p  t  h

SinkDrainerLe

ftOffset

SinkDrainerRig

htOffset

  S i  n  k   D  r  a i  n  e  r  B  a  c  k   O  f  f  s  e  t

   S   i   n   k   T   a   p    P

   r   o   f   i   l  e

    W   i   d   t   h

 S  i n  k   T

 a p   L e

 n g t  h

   D  o  o  r   H  a  n  d l  e  P  o  s i  t i  o  n

   C  o  r  n  e  r  U  n i  t   W i  d  t  h

Depth

Depth

Width

  B  a  c  k  s  p l  a  s  h  T  h i  c  k  n  e  s  s

Width

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

PLAN

1/20

DIMENSIONS OVERVIEW

Page 5 of 17

Page 6: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 6/17

Panel Frame Thickness Bottom

Height

Backsplash Height

Top Thickness

Wall Unit Bottom Front Length

Bottom Base Offset

Shelves Distance

Draw Handle Thickness

 S  p a c  e

Door Handle Height

D o or  H a n d l   e Wi   d  t  h 

D

 o or  H a n d l   e Of  f   s  e t F r  o m  S i   d  e

Panel Frame Thickness Top

Sink Depth

Di  v i   d  er Di   s  t  a n c  e

Divider Height

Di  v i   d  er T  h i   c  k  n e s  s 

 S  y  m b  ol   L i   n e s 

Extractor Hood Middle Height

Extractor Hood Bottom Height

Extractor Hood Top Height

 E  x t r  a c  t  or  H o o d B  o t  t  o m  Wi   d  t  h Extractor Hood Height Position

Sink Tap Height

Wall Unit Height

Height

Wall Unit Bottom Length

 Wi   d  t  h 

Shelves Offset

T  h i   c  k  n e s  s  S i   d  e s 

Thickness Bottom

Draw Handle Offset From Top

Door Handle Offset From Top

Dr  a w H a n d l   e Wi   d  t  h 

  R  e  v i  t   C  o  n  t  e  n  t  ®

   C  o  p  y  r i  g  h  t  2  0  1  0 -  2  0  1  1  b  y   A  p l  o  L i   m i  t  e  d ,   A l l  R i  g  h  t  s  r  e  s  e  r  v  e  d

   R   F   A  1  9  3  5  4

   K i t  c  h  e  n

  E  L  E   V   A   T I   O   N  1  /  2  0

   D I   M   E   N   S I   O   N   S   O   V   E   R   V I   E    W

  P  a  g  e  6  o  f  1  7

Page 7: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 7/17

Door Thickness

Panel Glass Thickness

   B  a  c   k  s  p   l  a  s   h   H  e   i  g   h   t

   H  e   i  g   h   t

   W  a   l   l   U  n   i   t   F  r  o  n   t   L  e  n  g   t   h

   W  a   l   l   U  n   i   t   B  o   t   t  o  m    T

   h   i  c   k  n  e  s  s

   T  o  p   T   h   i  c   k  n  e  s  s

Door Handle Depth

   T  o  p   T   h   i  c   k  n  e  s  s

Top Front Offset

Top Front Offset

Skirting Offset

   D  o  o  r   H  a  n   d   l  e   H  e   i  g   h   t

Panel Glass Offset

   B  o   t   t  o  m    B

  a  s  e   H  e   i  g   h   t

   W  a   l   l   U  n   i   t   H  e   i  g   h   t

   H  e   i  g   h   t

Top Front Offset

Backsplash Thickness

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

DIMENSIONS OVERVIEW

Page 7 of 17

Page 8: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 8/17

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

12

34

56

89

1 FRIDGE

2 DRAWERS UNIT

3 COOKER/ OVEN

4 DOUBLE FLOOR UNIT

5 SINGLE FLOOR UNIT

6 SINK

7 CORNER UNIT

8 DOUBLE WALL UNIT

9 SINGLE WALL UNIT

10 SHELL WALL UNIT

11 WALL CORNER UNIT

FAMILY TYPES OVERVIEW

Page 8 of 17

7

10 11

Page 9: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 9/17

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

GRAPHICS

How to remove lines from oncefamily is setup in the project

Once you have set up your family in the project, you will notice that on theworktop there are lines that you may not want to show as shown above inImage A.

To remove these lines, there is a Tool in the Tool Bar which is called "LineWorks"

In the Type Selector, select the line style "Invisible Lines" to apply to the edgesin the model.

With the Linework tool actived & "Invisible Lines"Category selected,In the drawing area, highlight the edge lines by clicking once as shown in redlines in Image B.

Then click again and the result will be that the Line will dissapear as shown inImage C

We deliver this family as a furniture Category which does not allow you to jointhe units and clear the lines between. If it is not important to you that the familyis categorized as furniture and you do not want to have the dividing lines visible,then you can open the family in the family editor and change the familycategory from Furniture to Generic, this will then allow you to join the unitstogether once loaded back in to your project.

IMAGE A

IMAGE B

IMAGE C

Page 9 of 17

Page 10: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 10/17

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

Page 10 of 17

SAMPLE SETUP OPTIONS

FIG 11

FIG 12

FIG 13

FIG 14

FIG 15

FIG 16

Page 11: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 11/17

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

Page 11 of 17

SAMPLE SETUP OPTIONS

FIG 17 FIG 18

FIG 19 FIG 20

FIG 21

Page 12: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 12/17

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

Page 12 of 17

SAMPLE SETUP OPTIONS

FIG 22 FIG 23

FIG 24 FIG 25

FIG 26 FIG 27

Page 13: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 13/17

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

Page 13 of 17

SAMPLE SETUP OPTIONS

FIG 28

FIG 29

Page 14: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 14/17

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

SAMPLE SETUP OPTIONS

FIG 30 FIG 31

FIG 32

FIG 33

FIG 34 FIG 35

Page 14 of 17

Page 15: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 15/17

Fix Panel Offset

   B  a  c   k  s  p   l  a  s   h   L  e   f   t   O   f   f  s  e   t

   K   i  c   k  p   l  a   t  e   L  e   f   t   O   f   f  s  e   t

Top Profile Right Offset

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

NEW FEATURES IN VERSION 3.2

FIX PANEL

Page 15 of 17

FIG 36

FIG 38

FIG 40

FIG 37

FIG 39

FIG 41

Page 16: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 16/17

Top Right Side OffsetTop Left Side OffsetTop Back Offset

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

NEW FEATURES IN VERSION 3.2

Page 16 of 17

FIG 42

FIG 43

FIG 44

FIG 43

In the Type Parameters under:-

Graphics

To Create different sized drawers on top or bottom, adjust the Parameter ADDITIONAL DRAWERS COUNT from 0 to 2 and The DRAW COUNT from 0 to 1.Theresult will be an image as shown above. Please note the that the Additional Drawers are calculated in height. These Drawers will adjust in their height accordinglyby adjusting the parameters ADDITIONAL DRAWERS COUNT, DRAW COUNT DRAW HEIGHT & HEIGHT 

Please note that the parameters DOORS VISIBILTY & JUST DRAWERS parameters should be unselected you want to create Drawers or Mixed sized Drawers

(PLEASE REFER TO DIMENSIONS OVERVIEW )

NEW FEATURES IN VERSION 3.3

Page 17: RFA19354 Kitchen Manual

8/3/2019 RFA19354 Kitchen Manual

http://slidepdf.com/reader/full/rfa19354-kitchen-manual 17/17

W   i  d   t  h  

Depth

   D  e  p   t   h

L e f  t  T  o  p  A n  g l  e 

L  e  f   t   B  a  c  k   L  e  f   t   O  f   f   s  e  t  

R  i   g  h  t   B  a  c  k   L  e  f   t   O  f   f   s  e  t  

R   i     g   h   t    T    

o   p    A   n    g   l    e  

K   i  c  k   p  l   a  t  e   O  f   f   s  e  t   L  e  f   t  

K   i  c  k   p  l   a  t  e   O  f   f   s  e  t   R  i   g  h  t  

Revit Content®

Copyright 2010 -2011 by Aplo Limited, All Rights reserved

RFA 19354Kitchen

NEW FEATURES IN VERSION 3.4

In the Type Parameters under:-

Graphics

To Create a corner unit which has a 45 degree panel opening, adjust the checkbox parameter CORNER UNIT 45 DEGREE .The result will be an image as shown above. Please note the that all parameters are valid for this setup.

 (PLEASE REFER TO DIMENSIONS OVERVIEW )

Page 17 of 17

FIG 46

FIG 45

In the Instance Parameters under:-

Dimensions

To Create an arrragement of mitered unit i.e. 15 degrees, adjust the parameters which can be found under the Instance Parameters (PLEASE REFER TO DIMENSIONS OVERVIEW )