Rf Punch 200
-
Upload
kevin-jones -
Category
Documents
-
view
22 -
download
6
description
Transcript of Rf Punch 200
® ®
INSTALLATION & OPERATION
MANUAL
PUNCH 40ix / PUNCH 60ix
PUNCH 100ix / PUNCH 200ix
2-CHANNEL DSM AMPLIFIERS
Dear Customer,
Congratulations on your purchase of the world's finest brand of car audioamplifiers. At Rockford Fosgate we are committed to musical reproduction at itsbest, and we are pleased you chose our product. Through years of engineeringexpertise, hand craftsmanship and critical testing procedures, we have created awide range of products that reproduce music with all the clarity and richness youdeserve.
For maximum performance we recommend you have your new Rockford Fosgateproduct installed by an Authorized Rockford Fosgate Dealer, as we providespecialized training through Rockford Technical Training Institute (RTTI). Pleaseread your warranty and retain your receipt and original carton for possible futureuse.
To add the finishing touch to your new Rockford Fosgate image order your Rockfordaccessories, which include everything from T-shirts and jackets to hats andsunglasses.
To get a free brochure on Rockford Fosgate products and Rockford accessories, inthe U.S. call 602-967-3565 or FAX 602-967-8132. For all other countries, call+001-602-967-3565 or FAX +001-602-967-8132.
The serial number can be found on the outside of the box. Please record itin the space provided below as your permanent record. This will serve asverification of your factory warranty and may become useful in recoveringyour amplifier if it is ever stolen.
Serial Number: ____________________
Model Number: ____________________
If, after reading your manual, you still have questions regarding thisproduct, we recommend that you see your Rockford Fosgate dealer. If youneed further assistance, you can call us direct at 1-800-795-2385. Be sure tohave your serial number, model number and date of purchase availablewhen you call.
PRACTICE SAFE SOUND™CONTINUOUS EXPOSURE TO SOUND PRESSURE LEVELS
OVER 100dB MAY CAUSE PERMANENT HEARING LOSS. HIGH
POWERED AUTO SOUND SYSTEMS MAY PRODUCE SOUND
PRESSURE LEVELS WELL OVER 130dB. USE COMMON SENSE
AND PRACTICE SAFE SOUND.
TA B L E O F CO N T E N T S
Introduction ...................................................................................... 1
Punch 2-Channel Amplifier Accessory Pack ...................................... 1
Rockford Fosgate Accessories ............................................................ 2
Technical Design Features ................................................................ 3
Design Features ................................................................................. 6
Installation Considerations ................................................................ 8
Mounting Location ............................................................................ 9
Battery and Charging....................................................................... 10
Wiring the System ........................................................................... 10
Using the XCard .............................................................................. 13
Basic Connections........................................................................... 14
System Diagrams............................................................................. 18
Troubleshooting .............................................................................. 22
Dynamic Power Measurements ....................................................... 24
Specifications .................................................................................. 26
Warranty Information ...................................................................... 28
G E T T I N G S TA R T E DWelcome to Rockford Fosgate! This manual is designed to provide
information for the owner, salesperson and installer. For those of
you who want quick information on how to install this product,
please turn to the Basic System Diagrams in the Installation section
of this manual. Other information can be located by using the Table
of Contents. We, at Rockford Fosgate, have worked very hard to
make sure all the information in this manual is current. But, as we
are constantly finding new ways to improve our product, this
information is subject to change without notice.
– 1 –
I N T R O D U C T I O N
Rockford engineers designed the Punch 2-channel amplifiers towithstand the rugged automotive environment while deliveringsuperior sound quality in a flexible, reliable, and efficient pack-age. A grounding technique called TOPAZ was used to eliminatenoise problems associated with car audio systems, while flexibil-ity was accomplished with the use of a built-in XCard. Reliabilitywas accomplished with the use of protection circuits called RTPand NOMAD, while MOSFET and DSM technology improveamplifier efficiency. The result of these components give thePunch amplifier awesome sound quality in a “Bullet Proof”package. An explanation of these technologies, some exclusivelydesigned by Rockford, are described in the Technical DesignFeatures.
PUNCH 2-CHANNEL AMPLIFIER
ACCESSORY PACK
The accessory pack shipped with the Punch 2-channel amplifiersincludes the mounting hardware necessary to secure them to thevehicle as well as attaching the end caps.
Installation & Operation ManualPunch Verification Certificate(1) 17' (518.16cm) Red Power Wire(1) 12' (365.76cm) Remote Turn-On Wire(1) 1.5' (45.72cm) Black Grounding Wire(1) Female Connector for Remote Turn-On Wire(1) Ring Terminal for Ground Wire(1) Ring Terminal for Battery Post(1) ATC Inline Fuseholder (Punch 40ix, 60ix, 100ix)(1) AGU Inline Fuseholder (Punch 200ix)(6) Hex Head Screws for speaker and power connectors(4) Mounting Screws for end caps(4) Mounting Screws for amplifier(1) Allen Wrench 7/64"(1) Allen Wrench 3/32"
– 2 –
ROCKFORD FOSGATE ACCESSORIES
The following accessories were designed to enhance the perfor-mance of the Punch 2-channel amplifiers.
Energy Storage CapacitorThe Punch capacitors are used to provide extra current needed byamplifiers to reproduce musical transients. The Punch Caps alsohave the natural ability to filter AC ripple caused by the alternator,reducing the chance of noise in the system. The Punch Caps willmaximize both the sound quality and performance that RockfordFosgate amplifiers can deliver.
Punch Link (FG-LINK)The Punch Link is a specially cast heatsink interconnect whichallows you to join any of our current Punch or Punch Poweramplifiers together. While providing additional cooling throughthe coupling process, the Punch Link adds the finishing touch bygiving you the look of one awesome amplifier.
XCard
Additional crossover card frequencies are available for special-ized requirements. You can get the following XCards from yourAuthorized Rockford Fosgate Dealer.
XM50 = 50Hz XM275 = 275HzXM70 = 70Hz XM400 = 400HzXM100 = 100Hz XM4.5k = 4,500HzXM150 = 150Hz XM6.5k = 6,500HzXM200 = 200Hz XM00 = Blank card for
custom crossover
– 3 –
TECHNICAL DESIGN FEATURES
TOPAZ (Tracking Operation Pre-Amplifier Zone)
The TOPAZ (Tracking Operation Pre-Amplifier Zone) circuitrysolves ground loop noise problems common to automotiveamplifier design. This innovative new development allows vastlyimproved isolation of the input signal grounds from the powersupply ground of the amplifier. This is accomplished by allowingthe source unit to control the potential “environment” of theentire input structure or “zone” of the amplifier. This processimproves the noise rejection of the amplifier by 30-40dB – anastounding 30-100 times better than amplifiers without TOPAZ.
THE RESULT: Elimination of troublesome ground loop noisebetween source and amplifier.
RTP (Real Time Protection)NOMAD (NOn-Multiplying AdvancedDecision)
The Punch and Power amplifiers use an analog computerprocess to maximize safe output power under all operatingconditions. Rockford Fosgate pioneered and developed RTP(Real Time Protection), a crucial element in the performanceedge of our amplifiers. The innovative NOMAD (NOn-Multiply-ing Advanced Decision) system is the most sophisticated versionof this technique ever used, bringing previously unavailablelevels of accuracy, stability, temperature immunity and reliabil-ity to this critical process. NOMAD makes advanced decisionsbased on device voltages to precisely control the awesome levelsof current available in the output MOSFETs to safe values – butonly when absolutely needed.
THE RESULT: Extremely fast protection system that alwaysprotects the amplifier and never degrades the sound.
– 4 –
DSM (Discrete Surface Mount) Technology
The DSM (Discrete Surface Mount) manufacturing process com-bines the advantages of both discrete components and integratedcircuitry. Rockford Fosgate is the only American amplifier manu-facturer to have invested millions into this process. DSM compo-nents differ from conventional discrete components in threedifferent ways. They are more compact, more rugged, and theytake much better advantage of the PC board to allow them to getrid of any heat they generate. Using them wherever appropriateallows the advantages associated with discrete circuitry to beretained while also providing room for both highly advancedprocessing features and generous PC board copper paths whereneeded. Their short lead-out structures allow maximum audioperformance and highest signal-to-noise ratios to be obtained inamplifiers of desirable package size without resorting to “ampli-fier-on-a-chip” shortcuts. These advantages are shown below inFigure 1.
Figure 1
Thru-Hole Surface Mount
Component
Solder
THE RESULT: Fewer connections, improved reliability, shortersignal paths, superior signal-to-noise ratio and awesome sonicperformance.
Solder
– 5 –
XCard (Internal Crossover)
The Punch and Power amplifiers utilize internal active crossovers.These crossovers have many performance advantages such as usingdiscrete components for exact frequency adjustments which are farsuperior to potentiometers. Additionally, the XCard can be config-ured for high-pass, low-pass and full range operation. With slightmodifications, many crossover frequencies and slope configurationscan be achieved.
THE RESULT: Increased system design flexibility with a preciseelectronic crossover without the limitations of conventional poten-tiometer designs.
MOSFET DevicesRockford Fosgate is one of the few manufacturers in the soundcommunity to utilize MOSFET devices in both the power supplyand the output stages. MOSFET (Metal Oxide SemiconductorField Effect Transistor) devices offer several important inherentadvantages over the 30 year old technology of bi-polar design.These advantages include: thermal stability, switching speed,ultra low output impedance and wider bandwidth linearity. Inaddition, MOSFETs and vacuum tubes share many importantoperating characteristics. However, the MOSFET device is muchfaster, wider in bandwidth, measurably lower in distortion and farmore linear than vacuum tubes.
THE RESULT: Operational characteristics of vacuum tubeswithout the performance limitations of tube design.
DESIGN FEATURES
1. Cast Aluminum Heatsink – The cast aluminum heatsink of thePunch amplifier dissipates heat generated by the amplifier'scircuitry. The inherent advantage of casting provides a 30%improvement of cooling over conventional extrusion heatsinkdesigns.
2. End Caps – Interchangeable end caps conceal the wiring andinput cables, giving the amplifier a clean “stealth” look.
– 6 –
3. Speaker Terminals – The heavy duty, gold-plated terminal blockconnectors (+ and –) will accept wire sizes from 8 AWG to 18AWG. These gold-plated connectors are immune to corrosionthat can cause signal deterioration.
4. Power Terminals – The power and ground connectors on thePunch amplifier are gold-plated and will accommodate up to 8AWG wire maximizing the input current capability of theamplifier.
5. REM Terminal – This spade terminal is used for the AP (autopower) or remote turn on of the Punch amplifier.
49 5
GNDB+
LED
REM
+ R –+ L –Bass
RightGain
RightInput
LeftInput
LeftGainTreble
Speaker Speaker
3 8 7 76 6 8 3
6. RCA Input Jacks – The industry standard RCA jacks provideeasy connections for signal level input. They are gold-plated toresist the signal degradation caused by corrosion.
7. Input Sensitivity Controls – The input level controls are presetfor 825mV which will match the output of most source units.They can be adjusted to match input levels ranging from 150mVto 3V.
8. Punch Equalization Controls – The Punch EQ helps correct foracoustical deficiencies of the listening environment. The Basscontrol allows a narrow band adjustment of up to 18dBcentered at 45Hz. The Treble control is a wide band hingedadjustment with a maximum of 18dB at 20kHz. The Punch EQcan be bypassed by turning the controls to their minimum orcounterclockwise position.
9. LED Power Indicator – The LED illuminates when the unit isturned on.
10. XCard (Internal Crossover) – This built-in crossover card isconfigurable for a multitude of operating frequencies. Theorientation of the card in its socket determines the function ofhigh-pass, low-pass, or full range operation.
– 7 –
FrontXCard
10
Low-Pass Full RangeHigh-Pass
HP
LP HP
LP FULL D S M
®
MOSFET AMPLIFIER®
100 Watts RMS continuous power per channel into 4 Ohms with less than 0.05% Total Harmonic Distortion from 20-20kHz.
ROCKFORD CORPORATIONMADE IN THE USA
®
XCard
INSTALLATION CONSIDERATIONS
– 8 –
This section focuses on some of the vehicle considerations forinstalling your new Punch amplifier. Checking your battery andpresent sound system, as well as pre-planning your system layout andbest wiring routes will save installation time. When deciding how tolay out your new system, be sure that each component will be easilyaccessible for making adjustments.
Before beginning any installation, be sure to follow these simple rules:
1. Be sure to carefully read and understand the instructions beforeattempting to install the amplifier.
2. For safety, disconnect the negative lead from the battery prior tobeginning the installation.
3. For easier assembly, we suggest you run all wires prior tomounting your amplifier in place.
4. Route all of the RCA cables close together and away from anyhigh current wires.
5. Use high quality connectors for a reliable installation and tominimize signal or power loss.
6. Think before you drill! Be careful not to cut or drill into gas tanks,fuel lines, brake or hydraulic lines, vacuum lines or electricalwiring when working on any vehicle.
7. Never run wires underneath the vehicle. Running the wiresinside the vehicle provides the best protection.
8. Avoid running wires over or through sharp edges. Use rubber orplastic grommets to protect any wires routed through metal,especially the firewall.
9. ALWAYS protect the battery and electrical system from damagewith proper fusing. Install a fuseholder and appropriate fuse onthe +12V power wire within 18” (45.7 cm) of the battery terminal.
10. When grounding to the chassis of the vehicle, scrape all paintfrom the metal to ensure a good, clean ground connection.Grounding connections should be as short as possible and alwaysbe connected to metal that is welded to the main body, or chassis,of the vehicle.
The following is a list of tools you will need for installing the Punchamplifier:
Allen wrenches 7/64" & 3/32" (included) VoltmeterWire strippers Battery post wrenchElectric hand drill w/assorted bits Wire cuttersWire crimpers Assorted connectors
MOUNTING LOCATION
– 9 –
The mounting location and position of your amplifier will have a greateffect on its ability to dissipate the heat generated during normaloperation. The design of our cast aluminum heatsink serves to easilydissipate the heat generated over a wide range of operating condi-tions. However, to maximize the performance of your amplifier, careshould be taken to ensure adequate ventilation.
Trunk MountingMounting the amplifier vertically on a surface with the fin groovesrunning up and down will provide the best cooling of the amplifier.
Mounting the amplifier on the floor of the trunk will work but providesless cooling capability than vertical mounting.
Mounting the amplifier upside down to the rear deck of the trunk willnot provide proper cooling and will severely affect the performanceof the amplifier and is strongly not recommended.
Passenger Compartment MountingMounting the amplifier in the passenger compartment will work aslong as you provide a sufficient amount of air for the amplifier to coolitself. If you are going to mount the amplifier under the seat of thevehicle, you must have at least 1" (2.54cm) of air gap around theamplifier's heatsink.
Mounting the amplifier with less than 1" (2.54cm) of air gap aroundthe amplifier's heatsink in the passenger compartment will notprovide proper cooling and will severely affect the performance of theamplifier and is strongly not recommended.
Engine Compartment MountingRockford Fosgate amplifiers should never be mounted in the enginecompartment. Not only will this void your warranty but could createan embarrassing situation caused by the ridicule from your friends.
Amplifiers will put an increased load on the vehicle's battery andcharging system. We recommend checking your alternator andbattery condition to ensure that the electrical system has enoughcapacity to handle the increased load of your stereo system. Stockelectrical systems which are in good condition should be able tohandle the extra load of any Rockford amplifier without problems,although battery and alternator life can be reduced slightly. Tomaximize the performance of your Rockford Fosgate amplifier, wesuggest the use of a heavy duty battery, high output alternator and anenergy storage capacitor.
– 10 –
BATTERY AND CHARGING
WIRING THE SYSTEM
CAUTION: Avoid running power wires near the low level inputcables, antenna, power leads, sensitive equipment or harnesses. Thepower wires carry substantial current and could induce noise into theaudio system.
• For safety, disconnect the negative lead from the battery prior tobeginning the installation.
1. Plan the wire routing. Take care when running signal level RCAcables to keep them close together but isolated from the amplifier'spower cables and any high power auto accessories, especiallyelectric motors. This is done to prevent coupling the noise fromradiated electrical fields into the audio signal. When feeding thewires through the firewall or any metal barrier, protect them withplastic or rubber grommets to prevent short circuits. Leave thewires long at this point to adjust for a precise fit at a later time.
2. Prepare the Power cable for attachment to the amplifier bystripping 5/8" of insulation from the end of the wire. The use of 8gauge power cable can interfere with the installation of the endcaps. Proper wire dress can prevent this from occurring. Toprevent the wire from fraying, strip the insulation at a 45° angle.Insert the bared wire into the B+ terminal with the long side of theinsulation on the top. Bend the cable down at a 90° angle. Tightenthe set screw to secure the cable in place.
– 11 –
Punch 40ix, 60ix, 100ixTrim the power cable to within 18" of the battery and install theprotective rubber boot, which is packed with the fuseholder,over the end of the wire. Strip 3/8" of insulation from the wireand insert into the end of the fuseholder, then crimp it in place.Slide the rubber boot into place to cover the connection. Usethe section of cable that was trimmed earlier and connect it tothe other end of the fuseholder.
Punch 200ixMount the fuseholder within 18" of the battery using two (2) #8screws. Disassemble the fuseholder. You should have 2 blackplastic end caps, 2 gold-plated fuse clips, a plastic spacer andthe fuseholder body. Trim the amplifier power cable to reachthe fuseholder and strip the wire 3/8". Slide one of the end capsover the wire (narrow end first) and insert the wire into one ofthe fuse clips. Tighten the set screw. Screw the black end capto the fuseholder body to secure the cable. Use the section ofcable that was trimmed earlier and connect it to the other endof the fuseholder. Install the plastic spacer in the fuseholderand attach the cable to the fuseholder body.
NOTE: The B+ cable MUST be fused 18" or less from thevehicle's battery. Install the fuseholder under the hood andprepare the cable ends as stated above. Connections shouldbe water tight.
3. Strip 3/8" from the battery end of the power cable and crimpthe large ring terminal to the cable. Use the ring terminal toconnect to the battery positive terminal. Do not install the fuseat this time.
4. Prepare a length of cable to be used for the ground connection.Strip 5/8" of insulation from the end of the cable as describedpreviously and connect to the appropriate terminal of theamplifier. Prepare the chassis ground by scraping any paintfrom the metal surface and thoroughly clean the area of all dirtand grease. Strip the other end of the wire and attach a ringconnector. Fasten the cable to the chassis using a non-anodized screw and star washers.
5. Prepare the REM turn-on wire for connection to the amplifierby stripping 5/8" of insulation from the wire end and crimpingan insulated spade connector in place. Slide the connectorover the REM terminal on the amplifier. Connect the other endof the REM wire to a switched 12 volt positive source. Theswitched signal is usually taken from the source unit's autoantenna or the accessory lead. If the source unit does not havethese outputs available, the recommended solution is to wirea mechanical switch in line with a 12 volt source to activatethe amplifier.
6. Connect the source signal to the amplifier by plugging the RCAcables into the input jacks at the amplifier.
7. Connect the speakers. Strip the speaker wires 5/8" and insertinto the appropriate terminal on the amplifier. Insert the baredwire into the speaker terminal and tighten the set screw tosecure into place. Be sure to maintain proper speaker polarity.DO NOT chassis ground any of the speaker leads as unstableoperation may result.
8. Perform a final check of the completed system wiring to ensurethat all connections are accurate. Check all power and groundconnections for frayed wires and loose connections whichcould cause problems.
9. After the final inspection is complete, install the power fuseand enjoy listening. During the initial listening period, youmay need to “fine tune” any phasing and level settings withinyour particular vehicle. To aid in this procedure, play a trackwith high musical content and cruise around your neighbor-hood. After fully evaluating the transient response of yoursystem and making any final adjustments, all your neighborswithin a 1 mile radius will assume that you have just success-fully completed another upgrade to your audio system forwhich they will probably spill thumbtacks on your driveway.
– 12 –
– 13 –
USING THE XCARD
The crossover functions are controlled through the use of anXCard and can be set for high-pass, low-pass or full rangeoperation. Each crossover card has two faces: one face operatesFull Range, the other has arrows to indicate the edge for selectingHP (high-pass) or LP (low-pass) operation. Orient the card withthe desired operating edge, indicated by the arrow, toward thesocket terminals inside the amplifier. Firmly, but carefully, plugthe card into the socket.
The crossover point can be altered by changing the resistor value.Use the following formula to select the appropriate resistor valueto be placed on the XCard.
3386fo
= R (in kΩ) for .047µf cap
= R (in kΩ) for .022µf cap7234fo
Where: R = Ωfo = desired crossover frequencyc = capacitor in faradsex: .047 x 10-6 for .047mf cap
Crossover CardHigh PassLow PassFull Range
R1
R2
R1
R2FULL
The actual formula is:
R =1
2πfoc
Low-Pass Full RangeHigh-Pass
FULL HP
LP HP
LP
BASIC CONNECTIONS
– 14 –
*Keep grounds as short as possible.
LED
REM
Connect to remote turn-on lead of
source unit.
Connect to chassis ground of vehicle*
Connect to B+ of battery with appropriate fuse value.
Less than 18"
GNDB+
P40ix
P60ix
P100ix
P200ix
- 20A
- 30A
- 40A
- 50A
Power Connections
– 15 –
Stereo Operation
BassRightGain
RightInput
LeftInput
LeftGainTreble
–
+
+ L –Speaker
+ R –Speaker
–
+
RCA Input
• RCA inputs are connected to both left and right channels.• Gain for left and right channels operate independently.• Impedance for each channel should be 2Ω minimum.• XCard can be set for High-Pass, Low-Pass or Full Range.
– 16 –
BassRightGain
RightInput
LeftInput
LeftGainTreble
+ –
+ L –Speaker
+ R –Speaker
RCA Input
4Ω
Mono Operation
• RCA inputs are connected to both left and right channels.• Gain for left and right channels are set equally to balance
the subwoofer.• Impedance for mono channel should be 4Ω minimum.• XCard can be set for High-Pass, Low-Pass or Full Range.
– 17 –
• RCA inputs are connected to both left and right channels.• Gain for left and right channels are set equally to balance
the subwoofer.• Impedance for each channel should be 2Ω minimum.• Impedance for mono channel should be 4Ω minimum.• XCard is set for Full Range
Stereo/Mono Operation
BassRightGain
RightInput
LeftInput
LeftGainTreble
+ L –Speaker
RCA Input
+ –
4Ω
–
+ –
+
+ R –Speaker
SYSTEM DIAGRAMS
– 18 –
2-Way System
D S M
®
4
PCH-142X
PCH-14X
PCH-54
PCH-142X
PCH-14X
PCH-54
100Hz HP or Full Range
XCard
12dB/octave HP100Hz
– 19 –
3-Way System
PCH-142X
PCH-14X
PCH-54
PCH-142X
PCH-14X
PCH-54
D S M
®
4D S M
®
6
RFP-8128Ω
RFP-8128Ω
Front Rear
100Hz LP
XCard
100Hz HP
XCard
12dB/octave HP100Hz
12dB/octave LP100Hz
4-Way System
– 20 –
PCH-142X
PCH-14X
PCH-54
PCH-142X
PCH-14X
PCH-54
D S M
®
4
Front
®
D S M
®®
D S M
®
6
RFP-8128Ω
RFP-8128Ω
100Hz HP24dB/octave HP
100Hz24dB/octave HP12dB/octave LP
275Hz
30Hz12dB/octave HP12dB/octave LP
100Hz
® ®
A P A S S I O N F O R P E R F O R M A N C E
3
RFA-64
RFA-64
100Hz HP12dB/octave HP
100Hz HP24dB/octave HP
30Hz12dB/octave HP
100Hz HP
XCard
275Hz LP
XCard
100Hz LP
XCard
4-Way System w/Fadable Rear Stage
– 21 –
PCH-142X
PCH-14X
PCH-54
PCH-142X
PCH-14X
PCH-54
D S M
®
4
100Hz HP
XCard
275Hz LP
XCard
Front
®
D S M
®®
D S M
®
6
RFP-8128Ω
RFP-8128Ω
100Hz LP
XCard
100Hz HP24dB/octave HP
100Hz24dB/octave HP12dB/octave LP
275Hz
30Hz12dB/octave HP12dB/octave LP
100Hz
® ®
A P A S S I O N F O R P E R F O R M A N C E
3
RFA-64
RFA-64
100Hz HP12dB/octave HP
100Hz HP24dB/octave HP
30Hz12dB/octave HP
D S M
®
4
PCH-142X
PCH-14X
PCH-54
PCH-142X
PCH-14X
PCH-54
100Hz HP
XCard
Rear
TROUBLESHOOTING
– 22 –
Amplifier does notturn on(Power LED is off)
Symptom Diagnosis Remedy
Voltage applied to theREM terminal of theamplifier is not between10.5 and 15.5 volts orthere is no voltagepresent.
Voltage to the B+ termi-nal of the amplifier isnot between 10.5 and15.5 volts or there is novoltage present.
Amplifier is not prop-erly grounded.
Amplifier has nosound(Power LED is on)
RCA Input from sourceunit is not connected ornot functioning prop-erly.
XCard is missing or notplaced properly in cross-over slots.
Speaker leads areshorted to each other orto the chassis of the ve-hicle.
Speakers are defective.
Check connections, substi-tute with known workingsource and cables and repairor replace as necessary.
Check XCard position andrepair or replace as neces-sary.
Disconnect existing speak-ers and test with knownworking speakers and wires.If amplifier plays, check andrepair wiring and installa-tion of speakers as neces-sary.
Disconnect existing speak-ers and test with knownworking speakers. If ampli-fier plays, check and repairspeakers as necessary.
Check the alternator, bat-tery, fuse, and wiring andrepair as necessary. If thevoltage is above 15.5 volts,have the electrical systeminspected by an authorizedcar service center.
Check the alternator, bat-tery, fuse, and wiring andrepair as necessary. If thevoltage is above 15.5 volts,have the electrical systeminspected by an authorizedcar service center.
Check wiring and repair asnecessary.
Speaker OutputLow or Distorted
Readjust input gains ofamplifier.
Check system with knownworking source and repairor replace original sourceas needed.
Check XCard position andrepair or replace as neces-sary.
Check the alternator, bat-tery, fuse, and power andground wiring. Repair asnecessary.
Symptom Diagnosis Remedy
Input gain signal foramplifier is incorrectlyset.
Source unit output toolow or source unit hasno output.
XCard is missing or notplaced properly in cross-over slots.
Low battery voltage orlarge voltage drops tothe amplifier under load.
– 23 –
Amplifier Noise(Turn-on Pop)
Voltage spike from out-put of preceding com-ponent is entering am-plifier through input sig-nal.
Voltage spike from re-mote turn-on lead isentering through REMinput terminal.
Disconnect input signal toamplifier and turn ampli-fier on and off. If noise iseliminated, connect REMlead of amplifier to sourceunit with a delay turn-onmodule.
Use a different 12 voltsource for REM lead ofamplifier. (i.e., battery di-rect) If noise is eliminated,use a relay to isolate am-plifier from noisy turn-onoutput.
– 24 –
Noise is radiating intoRCA signal cable.
Bad component in the sig-nal chain.
Noise is radiating intospeaker cables.
Multiple grounds in theaudio system.
Ground loop betweensource unit and antenna.
Engine Noise
Symptom Diagnosis Remedy
Check connections, run theRCA cables on a differentroute away from sources ofhigh voltage.
Check connections, bypassadditional components(crossovers and equalizers)between the source unitand the amplifier. Connectone component at a timeto determine the culprit.Repair or replace compo-nents as necessary.
Disconnect existing speak-ers and connect a testspeaker to the output ter-minals of the amplifier. Ifnoise is gone, reroute thespeaker cables away fromsources of high voltage.
Check ground connectionsand connect amplifiers, sig-nal processors, and othercomponents to a centrallocation or try a differentgrounding point on thechassis.
Check connections, dis-connect antenna fromsource unit. If noise is gone,install an antenna groundloop isolator.
• If noise persists, see your Authorized Rockford Fosgate Dealer.
– 25 –
DYNAMIC POWER MEASUREMENTS
About the Dynamic Power MeasurementsThe Audio Graph PowerCube is a test instrument used to measure theoutput of an amplifier in accordance with IHF-202 industry stan-dards. The IHF-202 standard is a dynamic power measurement andwas developed as a means of measuring power in a manner that bestrepresents the Real World operation of an amplifier. Many manufac-turers, including Rockford Fosgate, at times will measure amplifierpower into a fixed resistor (4 Ohm, 2 Ohm). While this method isuseful in some types of evaluation and testing, it is not representativeof an amplifier that is connected to a speaker and playing music.
MusicMusic is dynamic; the sound waves are complex and constantlychanging. In order to simulate this, the IHF-202 standard calls for theinput signal to the amplifier to be a 1kHz bursted tone. This signal isinput (on for 20 milliseconds) and reduced 20dB for 480 millisec-onds. The signal is gradually increased in level until the amplifier'soutput exceeds 1% Total Harmonic Distortion (THD). At 1% distor-tion becomes audible, therefore, any power produced above thatlevel is considered not usable. Many manufacturers represent theiramplifiers' output power in excess of 10% distortion. They use manynames for this measurement, such as Total Maximum Power orMaximum Output Power. This is not indicative of the actual usableoutput power.
Listening to Loudspeakers - Not ResistorsA loudspeaker is not a resistor. A resistor's value (resistance measuredin ohms) is fixed. A loudspeaker's impedance is dynamic. It isconstantly changing in value, dependent upon the frequency of theinput signal. Therefore, measuring power with the amplifier loadedinto a 4 ohm resistor is not the same as measuring power with theamplifier connected to a 4 ohm speaker. Most people do not listen tomusic through a resistor.
A 4 Ohm speaker may experience a drop in impedance 4-6 times lowerthan its nominal (printed) impedance. A speaker will also create phaseshifts in the signal that is passed through it. These phase shifts happenbecause a speaker is an inductor (voice coil) and a capacitor (compli-ance of the surround/spider), as well as a resistor (voice coil wire).
To simulate a speaker the Audio Graph PowerCube measures outputpower into 20 different loads. It tests at 8 Ohms, 4 Ohms, 2 Ohms and1 Ohm. Each of these impedances is also tested at –60°, –30°, 0°, +30°and +60° phase angles. These different impedances and phase anglesrepresent the shifts in impedance and phase that can occur in a typicalloudspeaker.
Information CubedThe data acquired in the testing procedure is then graphed in the formof a 3-dimensional cube. Hence the name PowerCube.
The Phase Angle is expressed on the horizontal axis, the OutputVoltage is presented on the vertical axis and the Impedance isdisplayed on the Z axis. Output Power, in watts, is listed on the lefthand side for each impedance at each phase angle.
What is an Amplifier?An amplifier by definition is a voltage generating device, recreatingthe signal which is input to it identically but with increased volume.It will be connected to a reactive load (the speaker). The impedanceof this load and phase of the signal passing through the load will vary,dependent upon the frequency of the input signal (music).
Therefore, a perfect amplifier will be able to maintain the same outputvoltage regardless of load characteristics and will not alter the signalit is reproducing. A perfect amplifier when measured by theAudioGraph PowerCube would present data that forms a perfectcube. Unfortunately, amplifiers are not perfect. The laws of physicsgenerally prevent it. A great amplifier is about the best one can hopeto attain.
As you can see by the PowerCube and as you will experience bylistening, your Punch amplifier is a GREAT AMPLIFIER!
– 26 –
–60° (Cap)0°
(Ind) +60°1Ω
2Ω4Ω
Impedance
8Ω
10V
30V
50V
8Ω –60°–30°
0°30°60°
4Ω –60°–30°
0°30°60°
2Ω –60°–30°
0°30°60°
1Ω –60°–30°
0°30°60°
84 W84 W83 W84 W85 W
159 W154 W153 W154 W158 W266 W251 W245 W248 W261 W378 W343 W333 W339 W373 W
AudioGraph – The PowerCube™
Amplifier:Serial No:Owner :
PUNCH 200ix 14.4V x 2
ROCKFORD CORPORATION
Rated Power : 100 W @ 4 Ohms
IM
PE
DA
NC
E
MODEL BEING TESTED
x2 = STEREOMONO = BRIDGED MONO
VOLTAGE FROM BATTERY
OU
TP
UT
V
OL
TA
GE
*
*
*
*
PHASE ANGLES
POWER IN
WATTS
• Example of a 200ix PowerCube
– 27 –
PUN
CH
40i
xPU
NC
H 6
0ix
PUN
CH
100
ixPU
NC
H 2
00ix
Dyn
amic
Pow
er R
atin
g (IH
F-20
2 St
anda
rd) -
Mea
sure
d at
14.
4 V
olts
Mon
o in
to a
4Ω
Loa
d16
0 W
atts
260
Wat
ts42
0 W
atts
500
Wat
ts
Per
chan
nel i
nto
a 2Ω
Loa
d 7
5 W
atts
130
Wat
ts20
0 W
atts
240
Wat
ts
Per
chan
nel i
nto
a 4Ω
Loa
d 4
0 W
atts
80
Wat
ts11
0 W
atts
150
Wat
ts
Con
tinuo
us P
ower
Rat
ing
(Com
petit
ion
Stan
dard
) - M
easu
red
at 1
2.6
Bat
tery
Vol
ts
RM
S co
ntin
uous
pow
er p
er c
hann
el,
both
cha
nnel
s dr
iven
into
a 4
Ω lo
ad 2
0 W
atts
30
Wat
ts 5
0 W
atts
100
Wat
tsfr
om 2
0 to
20,
000
Hz
with
less
than
0.05
% T
otal
Har
mon
ic D
isto
rtio
n (T
HD
)
RM
S co
ntin
uous
pow
er p
er c
hann
el,
both
cha
nnel
s dr
iven
into
a 2
Ω lo
ad 4
0 W
atts
60
Wat
ts10
0 W
atts
200
Wat
tsfr
om 2
0 to
20,
000
Hz,
with
less
than
0.1%
Tot
al H
arm
onic
Dis
tort
ion
(TH
D)
RM
S co
ntin
uous
pow
er m
ono
into
a4Ω
load
from
20
to 2
0,00
0 H
z, w
ith 8
0 W
atts
120
Wat
ts20
0 W
atts
400
Wat
tsle
ss th
an 0
.1%
Tot
al H
arm
onic
Dis
tort
ion
(TH
D)
Sign
al-t
o-N
oise
Rat
io>
100
dB A
-wei
ghte
d
SP
EC
I FIC
AT
ION
S
PUN
CH
40i
xPU
NC
H 6
0ix
PUN
CH
100
ixPU
NC
H 2
00ix
Dim
ensi
ons
9-5/
8" (2
4.4c
m) W
9-5
/8"
(24.
4cm
) W 9
-5/8
" (2
4.4c
m) W
9-5
/8"
(24.
4cm
) W9-
5/8"
(24.
4cm
) L10
-5/8
" (2
7.0c
m) L
11-5
/8"
(29.
5cm
) L12
-5/8
" (3
2.0c
m) L
2-5/
8" (
6.6
cm) H
2-5
/8"
( 6.
6cm
) H 2
-5/8
" (
6.6c
m) H
2-5
/8"
( 6.
6cm
) H
Ban
dwid
th10
Hz
to 2
00kH
z ±3
dB
Dam
ping
Fac
tor
@ 4
ΩA
t out
put c
onne
ctor
- O
ver
200
Freq
uenc
y R
espo
nse
20H
z to
20k
Hz
±1.0
dB /
10H
z to
100
kHz
±0.5
dB
Slew
Fac
tor
50 V
olts
µs
IM D
isto
rtio
n (IH
F)Le
ss th
an 0
.05%
Inpu
t Sen
sitiv
ityV
aria
ble
from
150
mV
to 3
VPr
eset
at t
he fa
ctor
y fo
r 50
0mV
Prot
ectio
nR
TP/N
OM
AD
- In
tern
al a
nalo
g-co
mpu
ter
outp
ut p
rote
ctio
n ci
rcui
try
limits
pow
er in
cas
e of
over
load
. The
rmal
sw
itch
shut
s do
wn
the
ampl
ifier
in c
ase
of o
verh
eatin
g.
Bat
tery
Fus
ing
Rat
es20
Am
ps30
Am
ps40
Am
ps50
Am
ps(E
xter
nal t
o A
mpl
ifier
)Fu
se T
ype
ATC
ATC
ATC
AG
U
Equa
lizat
ion
Bas
s: +
18dB
Max
imum
at 4
5Hz
Treb
le:
+12
dB M
axim
um a
t 20k
Hz
Inpu
t Im
peda
nce
20,0
00 O
hns
Spec
ifica
tions
sub
ject
to c
hang
e w
ithou
t not
ice.
– 28 –
WA R R A N T Y IN F O R M AT I O N
Rockford Fosgate warrants all electronics to the original consumer/purchaser tobe free from defects in materials or workmanship for a period of three (3) years.We will cover parts and labor provided the product was purchased from anAuthorized Rockford Fosgate Dealer. This warranty does not apply to any producton which the seals and/or serial number have been broken, removed, tamperedwith, defaced or altered in any manner. This warranty only applies to the originalconsumer/purchaser and is not transferable.
Electronics found to be defective during the warranty period will be repaired orreplaced at Rockford Fosgate’s discretion. Repaired or replaced electronics willbe covered by the balance of the original warranty period only. Rockford Fosgateshall not be responsible for any incidental or consequential damages resultingfrom a defect in electronics. Some states do not allow the exclusion or limitationof incidental or consequential damages, so the previous limitation may not beapplicable.
The warranty does not cover any appearance item, any cost or expense related tothe removal or reinstallation of the product, any accessory used in conjunctionwith the product, damage to the product resulting from alteration, accident,misuse or abuse, or improper installation. This warranty does not apply if the partsor labor, which would otherwise be provided without charge under this warranty,are obtained from any source other than Rockford Fosgate or an AuthorizedRockford Fosgate Service Center.
This warranty is the only express warranty and does not create any impliedwarranties. Rockford Fosgate limits its obligations under any implied warrantiesunder state laws to a period not to exceed the written warranty period. Some statesdo not allow limitation on how long an implied warranty lasts, so the abovelimitation may not apply. This warranty applies only to products sold in the UnitedStates of America or its possessions. For warranty outside the U.S.A., pleasecontact the nearest Authorized Rockford Fosgate Dealer. This warranty gives theconsumer specific legal rights, and the consumer may have other rights which varyfrom state to state.
A defective product must be shipped prepaid to the Authorized Rockford FosgateDealer from which the consumer purchased the product or to the RockfordFosgate factory in Tempe, Arizona in the original factory carton or equivalent. Anyshipping loss or damage will be borne by the consumer or the consumer’s shipper.A consumer returning a product to the factory must call (800) 669-9899 for aReturn Authorization Number. All shipments shall be clearly marked with theReturn Authorization Number on the outside of the shipping carton.
Ship to:Rockford CorporationWarranty Repair Department2055 E. 5th StreetTempe, AZ 85281 U.S.A.Return Authorization Number:_________________
NO T E S
NO T E S
Rockford FosgateRockford Corporation
546 South Rockford DriveTempe, Arizona 85281 U.S.A.
In U.S.A., (602) 967-3565In Canada, Fax Korbon (905) 567-1929
In Europe, Fax (49) 4207-801250In Japan, Fax (81) 559-79-1265
3/95MAN-0915-A