Revel Bikes: Rail, Rascal, & Ranger Bearing & Linkage ...
Transcript of Revel Bikes: Rail, Rascal, & Ranger Bearing & Linkage ...
Revel Bikes: Rail, Rascal, & Ranger
Bearing & Linkage Removal/Install
Service and maintenance of Revel bicycles require shop grade tools and knowledge of working on bicycles. It is always
recommended to take your Revel bike to a professional for service and maintenance. Always wear eye protection. It is
critical to use the proper tools, Loctite, grease, and torque specifications during assembly. Failure to follow these
instructions may result in serious bodily injury or death, and damage to your beloved bike!
Tool list (Rail, Rascal, & Ranger):
● 8mm, 6mm, and 4mm Allen wrenches
● Torque wrench with 8mm, 6mm, and 4mm hex bits
● Bearing removal tool (Enduro BearingsTM blind hole puller or Wheels ManufacturingTM bearing extractor with punch and
hammer)
● Bearing press with drifts for 6801 bearing (12x21mm)
● Medium weight grease
● Blue 243 or 242 LoctiteTM medium thread locker
● Standard sharpie marker, any color of the rainbow
● Clean towel and isopropyl alcohol
Additional tools for Ranger only:
● T25 Torx Wrench
● Bearing press drifts for 6901 bearings (12x24mm)
Replacement parts:
● REVEL Rail/Rascal Bearing kit: 18 x 6801 (12x21x5mm) full complement or Max type bearings
● REVEL Ranger Bearing kit: 6 x 6801 (12x21x5mm) full complement or Max type bearings, 12 x 6901 (12x24x6mm) full
complement or Max type bearings
● If needed: REVEL Rail/Rascal Hardware kit, or REVEL Ranger Hardware kit
Part No. Name Specification
1 310-FRA18-0131 Forward Shock Mount Bolt M6 x P1.0 x 15mm2 310-FRA18-0130 Forward Shock Mount Axle M6 x P1.0 x 39mm3 310-FRA18-0129 Forward Shock Mount Washers 13.8m x 8.5m x 1mm
4 310-FRA18-0128 Rear Shock Mount Bolt M10 x 27.9mm
5 310-FRA18-0126 Pivot #5 Axle M8 x P1.25 x L18mm
6 310-FRA18-0127 Pivot #3/5 Bolt M8 x P1.25 xL15.5mm
7 310-BEA18-6801 6801 Full Compliment Bearings 12 x 21 x 5mm
8 310-FRA18-0125 Pivot #5 Spacer 20 x 12.2 5.15mm
9 310-FRA18-0122 Pivot #3 Axle M8 x P1.25 x 24.5mm
10 310-FRA18-0121 Pivot #3 Spacer 20 x 12.2 x 7mm
11 310-FRA18-0120 Pivot #2 Axle M8 x P1.25 x 64mm
12 310-FRA18-0117 Pivot #1/2/4 Bolt M8 x P1.25 x 23mm
13 310-FRA18-0115 Pivot #1/4 Spacer 20 x 12.2 x 2mm
14 310-FRA18-0118 Pivot #2 Inner Spacer 12.1 x 14.5 x 22mm
15 310-FRA18-0116 Pivot #1 Axle M8 x P1.25 x 75mm
16 310-FRA18-0119 Pivot #2 Spacer 20 x 12.2 x 1.5mm
17 310-FRA18-0114 Pivot #1 Inner Spacer 12.1 x 14 x 35mm
18 310-FRA18-1124 Pivot #4 Axle M8 x P1.25 x 80.2mm
19 310-FRA18-0113 Chian guide Revel Rail/Rascal Custom
20 310-FRA18-1123 Pivot #4 Inner Spacer 12.1 x 14 x 24.9mm
22 310-HAN18-0107 Deraileur Hanger Revel Rail/Rascal Custom
23 310-FRA18-0109 Chainstay Protector Revel Rail/Rascal Custom24 310-FRA18-0110 Downtube Protector Revel Rail/Rascal Custom26 310-FRA18-0112 Socket Cap Screws M5 x P0.8 x 12mm27 310-FRA18-1101 Rail Front Triangle Revel Rail 28 310-FRA18-1105 Yoke/Pusher Link Revel Rail
29 310-FRA18-1104 Upper Link Revel Rail 30 310-FRA18-1103 Lower Link Revel Rail
31 310-FRA18-1102 Rail Rear Triangle Revel Rail
32 310-HAN18-0108 Deraileur Hanger Bolt M6 x P1.0 x 8 x 13.9mm
33 310-FRA18-0111 Downtube Hose Clamp Revel Rail/Rascal Custom
REVEL RAIL Part Numbers
�
�� �� � �� � �� ��
� � �
�
�
�� �� � �� � �� ��
�� �� � �� � ���
��
��
��
�
�� � � ���� ��
���
��
��
�
��
�
��
REVEL RASCAL Part Numbers
Part No. Name Specification
1 310-FRA18-0131 Forward Shock Mount Bolt M6 x P1.0 x 15mm2 310-FRA18-0130 Forward Shock Mount Axle M6 x P1.0 x 39mm3 310-FRA18-0129 Forward Shock Mount Washers 13.8m x 8.5m x 1mm
4 310-FRA18-0128 Rear Shock Mount Bolt M10 x 27.9mm
5 310-FRA18-0126 Pivot #5 Axle M8 x P1.25 x L18mm
6 310-FRA18-0127 Pivot #3/5 Bolt M8 x P1.25 xL15.5mm
7 310-BEA18-6801 6801 Full Compliment Bearings
12 x 21 x 5mm
8 310-FRA18-0125 Pivot #5 Spacer 20 x 12.2 5.15mm
9 310-FRA18-0122 Pivot #3 Axle M8 x P1.25 x 24.5mm
10 310-FRA18-0121 Pivot #3 Spacer 20 x 12.2 x 7mm
11 310-FRA18-0120 Pivot #2 Axle M8 x P1.25 x 64mm
12 310-FRA18-0117 Pivot #1/2/4 Bolt M8 x P1.25 x 23mm
13 310-FRA18-0115 Pivot #1 Spacer 20 x 12.2 x 2mm
14 310-FRA18-0118 Pivot #2 Inner Spacer 12.1 x 14.5 x 22mm
15 310-FRA18-0116 Pivot #1 Axle M8 x P1.25 x 75mm
16 310-FRA18-0119 Pivot #2 Spacer 20 x 12.2 x 1.5mm
17 310-FRA18-0114 Pivot #1 Inner Spacer 12.1 x 14 x 35mm
18 310-FRA18-2124 Pivot #4 Axle M8 x P1.25 x 79mm
19 310-FRA18-0113 Chian guide Revel Rail/Rascal Custom
20 310-FRA18-2123 Pivot #4 Spacer 20 x 12.2 x 6.5mm
22 310-HAN18-0107 Deraileur Hanger Revel Rail/Rascal Custom
23 310-FRA18-0109 Chainstay Protector Revel Rail/Rascal Custom24 310-FRA18-0110 Downtube Protector Revel Rail/Rascal Custom26 310-FRA18-0112 Socket Cap Screws M5 x P0.8 x 12mm27 310-FRA18-2101 Front Triangle Revel Rascal 28 310-FRA18-2105 Yoke/Pusher Link Revel Rascal 29 310-FRA18-2104 Upper Link Revel Rascal 30 310-FRA18-2103 Lower Link Revel Rascal 31 310-FRA18-2102 Rear Triangle Revel Rascal
32 310-HAN18-0108 Deraileur Hanger Bolt M6 x P1.0 x 8 x 13.9mm
33 310-FRA18-0111 Downtube Hose Clamp Revel Rail/Rascal Custom
�
�� �� � �� � �� ��
� � �
�
�
�� �� � �� � �� ��
�� � �� � �
��
��
��
�
�� � � ���� ��
���
��
��
��
�
��
�
# Part Number Name Specification Qty. Assembly Torque
1 320-00000-0007 Revel Ranger Rear Triangle 1
2 320-00000-0005 Revel Ranger Lower Link 1
3 320-00000-0004 Revel Ranger Upper Link 1
4 320-00000-0006 Revel Ranger Yoke/Pusher Link 1
5 320-00000-0002 Revel Ranger Front Triangle 1
6 310-00000-0028 Revel Axle 12 x 1.75 x 174mm 1 Grease 18 Nm
7 310-00000-0003 Rear Shock Mount Bolt M10 x 1.25mm 1 Ti Prep 15 Nm
8 320-00000-0001 Revel Swingarm Protector 1
9 320-00000-0008 Revel Ranger Downtube Protector 1
10 310-0000-0034 Pivot #4 Axle M8 x 1.25 x 97mm 1 Grease 10 Nm
11 310-BEA18-6901 6901 Full Compliment Bearings 12 x 24 x 6mm 12 Grease
12 310-00000-0045 Pivot #1/Pivot #2/Pivot #4 Bolt M8 x 1.25 x 12.5mm T25 3 Loctite 243 10 Nm
13 310-10021-0035 Pivot #1/Pivot #2/Pivot #4 Spacer 18 x 12.2 x 2mm 6
14 310-00000-0037 Pivot #4 Internal Axle Spacer 12.10 x 14 x 37.5mm 1
15 310-00000-0039 Pivot #2 Internal Axle Spacer 12.10 x 14 x 20mm 1
16 310-00000-0040 Pivot #2 Axle M8 x 1.25 x 65.5mm 1 Grease 10 Nm
17 310-00000-0036 Pivot #1 Axle M8 x 1.25 x 56.5mm 1 Grease 10 Nm
18 310-00000-0038 Pivot #1 Internal Axle Spacer 12.10 x 14 x 12mm 1
19 310-BEA18-6801 6801 Full Compliment Bearings 12 x 21 x 5mm 6 Grease
20 310-00000-0041 Pivot #3/Pivot #5 Spacer 12.2 x 17.5 x 5.8mm 4
21 310-00000-0043 Pivot #5 Axle M8 x 1.25 x 20mm 2 Grease 10 Nm
22 310-00000-0044 Pivot #3/Pivot #5 Bolt M8 x 1.25 x 11mm T25 4 Loctite 243 10 Nm
23 310-00000-0042 Pivot #3 Axle M8 x 1.25 x 25mm 2 Grease 10 Nm
24 310-00000-0015 Revel Ranger Derailleur Hanger M12 x 1.75mm 1
25 310-00000-0016 Revel Ranger Derailleur Hanger Bolt M12 x 1.75mm 1 Loctite 243 10 Nm
26 310-10021-0050 Forward Shock Mount Bolt M5 x 0.8 x 14mm T25 1 Ti Prep 10 Nm
27 310-10021-0051 Forward Shock Mount Axle M5 x 0.8 x 34mm 1 Grease 10 Nm
Revel Ranger Assembly Diagram
Disassembly of linkage and removal of bearing Removal of rear wheel, cranks, and chain guide is recommended.
1. Loosen all bolts while leaving axles, bolts and hardware in place. This make it easier to remove the pivot axles from their
pivots, reducing binding during removal.
2. Remove bolts, pivot axles, and spacers from position #5 and #6 using both a 6mm hex wrench and a 4mm hex wrench. Clean
pivot axles, bolts, and spacers and reassemble out of the frame, holding all spacers together so they don’t become lost or
swapped with other hardware. Carefully remove the yoke/shock assembly from the front triangle, placing it aside.
RANGER ONLY: Use a T25 Torx wrench in place of the 4mm Allen wrench.
3. Remove bolt, pivot axle, and spacers from pivot #4. Clean pivot axles, bolts, and spacers and reassemble out of the pivots,
holding all spacers together so they don’t become lost or swapped with other pivot spacers. Repeat process for pivots #3, #2,
and #1.
*Note: if rear brake and shifter are still attached, attaching the rear triangle to the front triangle, a strap (toe strap or VolleTM
work well) can be threaded through the BB and rear triangle to minimize kinking of the housing and hoses.
*Note: A SharpieTM marker can be used to push the pivot axle out of the pivot and/or hold the link in place without a pivot axle.
4. Only remove and replace bearings if needed: Remove all bearings using an Enduro BearingsTM blind hole puller slide hammer
or Wheels ManufacturingTM bearing extractor, punch, and hammer. Be careful to not damage the bearing spacer sleeve
between each bearing set in the frame and lower link. Be sure to remove the bearings straight out of the bore, avoiding any
tilting of the bearing as it is removed.
*Note: take care in holding rear triangle securely when removing bearings. Placing the rear triangle on a work bench with a
rubber matte ensures paint and rear triangle are not damaged.
5. Discard of any removed bearings and replace with the appropriate full complement or Max type bearings, per the exploded
view for your bike and using the instructions below. Rail and Rascal use 6801 bearings at all points, Ranger uses both 6801
and 6901 bearings.
Rail & Rascal Bearing installation:
6. Clean bearing bores and hardware with Isopropyl alcohol, and ensure you have new bearings and any replacement hardware
needed for reassembly.
7. Using a finger, apply a light coat of grease to each bearing bore before installation.
8. Using a bearing press with drifts for 6801 bearings, which are 12mm x 21mm in size, press each bearing into pivots #1, #2,
and #4. Double bearing pivots may require pressing one bearing in partially, then the next bearing to reach full press depth,
depending on the depth of your drift.
9. For pivots #3 and #4, press one bearing in at a time, with the bearing press sandwiching the bore location. DO NOT press
across the entire width of the rear triangle, as this could damage the frame.
Ranger Bearing installation:
6. Clean bearing bores and hardware with Isopropyl alcohol, and ensure you have new bearings and any replacement hardware
needed for reassembly.
7. Using a finger, apply a light coat of grease to each bearing bore before installation.
8. Using a bearing press with drifts for 6901 bearings, which are 12mm x 24mm in size, press each bearing into pivots #1, #2,
and #4. Double bearing pivots may require pressing one bearing in partially, then the next bearing to reach full press depth,
depending on the depth of your drift.
9. For pivots #3 and #4, using a bearing press with drifts for 6801 bearings, which are 12mm x 21mm in size, press one bearing
in at a time, with the bearing press sandwiching the bore location. DO NOT press across the entire width of the rear triangle,
as this could damage the frame.
Reassembly:
10. Staring at pivot #1, apply a thin layer of grease to the surface of the bearings. Stick the correct spacers to the surfaces of the
greasy bearing faces, with the spacer lip facing the bearing. Refer to the exploded view for proper spacer and hardware part
numbers/size.
11. Slide the lower link into position and use a SharpieTM marker as a guide pin to aid in lining up the link and spacers to the
bearings.
12. Apply a small amount of grease to the underside of where the pivot axle head and bolt head will meet the frame or link.
13. Apply a thin layer of grease to the #1 pivot axle, and install it into place, pushing the SharpieTM out of the pivot. No grease
should be present on the pivot axle threads
14. Apply 2 drops of thread locker to the pivot bolt threads. No grease should be present on the bolt threads.
15. Install the bolt lightly, but do not tighten. All bolts will be tightened after all links and hardware are in place.
16. Repeat steps 10-15 for Pivots #2, #3, then #4.
17. Using a torque wrench w/ 6mm hex bit and a 4mm Allen wrench, torque pivot bolts to 10Nm.
RANGER ONLY: Use a T25 Torx wrench in place of the 4mm Allen wrench.
18. Install the shock damper body eyelet into the yoke out of the frame. Apply a few drops of thread locker to the threads of the
M10 shock mount bolt. Apply a thin layer of the grease to the 15mm mount bolt shaft. Install bolt into the yoke, tightening
lightly.
19. Install the yoke/shock assembly into the frame and install the forward 10mm shock hardware into place. Use grease or Ti
prep if needed on the bolt threads.
20. Using a torque wrench w/ 4mm hex bit and a 4mm Allen wrench, torque forward shock bolt to 10Nm.
RANGER ONLY: Use a T25 Torx wrench in place of the 4mm Allen wrench.
21. Apply a thin layer of grease to pivot #5 axles and install it into place. No grease should be present on the pivot axle threads
22. Apply 2 drops of thread locker to the pivot #5 bolt threads. No grease should be present on the bolt threads.
23. Using a torque wrench w/ 6mm hex bit and a 4mm Allen wrench, torque pivot #5 bolts to 10Nm.
RANGER ONLY: Use a T25 Torx wrench in place of the 4mm Allen wrench.
24. Using a torque wrench w/ 8mm hex bit, torque rearward shock mount bolt to 15Nm.
25. Reinstall any other removed parts to the manufacturer's specifications.
GO RIDE YOUR BIKE!