oar.icrisat.orgoar.icrisat.org/8338/1/SPIA.pdfii Table of Contents LIST OF ACRONYMS ...
RETROFIT!KITS! - [email protected]!...
Transcript of RETROFIT!KITS! - [email protected]!...
HiLumzUSA.com [email protected]
PHONE: (1) 770-‐888-‐8338 FAX: 404-‐537-‐1900
Copyright © HiLumz® LLC 2014. All Rights Reserved. Product and company names mentioned herein may be trademarks of their respective owners. Product enhancements may result in specification changes without notice. Specifications are deemed accurate, but not guaranteed. Contact us for the most current information.
Diamonz® LED Retrofit Series
ADDITIONAL SPECIFICATIONS:
• LED L70 Life Hours: >100,000 @ 55°C • Beam Angle: (130W-‐125°) (40W / 75W – 115°) • Operating Temperature: -‐40°C to +60°C • Color Temperature: 5500K-‐STD • Protection: Short circuit / Over-‐current / Over-‐voltage / Over-‐temperature
protection with auto-‐recovery • Certification: (40W, 75W, 130W) ETL (UL-‐1598-‐C) & cETL (ANSI/UL 1598/
CAN/CSA C22.2)
ADDITIONAL FEATURES: • SUNON® MagLev Fan Technology: 70,000+ hours operating life suitable for 24/7
operation, providing a cool running LED unit. • Light Dispersion: Multiple lensing options available for maximum light distribution, if needed. • Mounting: Bracket mounting system or custom-‐fabricated plates to fit most any HID fixture.
HiLumz® Diamonz® 5/10 Year WARRANTY: Included in this warranty are the Diamonz® Retrofit Series or any fixture containing a Diamonz® LED engine. 5-‐year warranty on the LED Driver and 10-‐year warranty on all remaining components, including the LEDs, fan, heat sink, etc.
PRODUCT LED
WATTAGE NUMBER OF LEDs
AMPS REPLACES LUMENS*
CRI
VOLTAGE
L x W x H DIMENSIONS
FULL KIT WEIGHT
DZ40 Coming Soon
40W 21
1.67 100W – 175W HID TBD 70
100 – 277V 347 – 480V
(with step down transformer)
HEAD – 4.7" Diameter DRIVER – 6.4" x 1.7" x 1.3” 5 lbs.
DZ75 75W 42 3.1 250W HID 6,800 70 100 – 277V 347 – 480V
HEAD – 6.75" x 4.5" x 3.0" DRIVER – 8.7" x 2.4" x 1.5” 5.5 lbs.
DZ130 130W 16 5 400W HID 12,900 70 100 – 277V 347 – 480V
HEAD – 6.75” x 4.5” x 3.0” DRIVER – 8.7" x 2.7" x 1.5” 6 lbs.
DZ260 Dual Head 260W 32 10 750W HID 25,800 70 100 – 277V
347 – 480V Dual Heads Dual Driver 12 lbs.
DZ360 Tri-‐Head 360W 48 15 1000W HID 38,700 70 100 – 277V
347 – 480V Triple Heads Triple Driver 18 lbs
*Lumen values based on highest color temperature
DZ130
DZ75
Back of DZ130 and DZ75
RETROFIT KITS Easy Replacement for 95% of Traditional Fixtures
HiLumzUSA.com [email protected]
PHONE: (1) 770-‐888-‐8338 FAX: 404-‐537-‐1900
Copyright © HiLumz® LLC 2014. All Rights Reserved. Product and company names mentioned herein may be trademarks of their respective owners. Product enhancements may result in specification changes without notice. Specifications are deemed accurate, but not guaranteed. Contact us for the most current information.
DZ130 56 Optics
OPTICS SKU: Example
Product
ORDERING OPTIONS: When placing an order, build your SKU code by selecting the various options in each column below. Use the numbers in bold as the numbers/characters to create the appropriate SKU code. See example below. Example: HiLumz® Diamonz® 130W, 5500K Color Temp, 100-‐277V Driver Dimmable, with Y Bracket
OTHER OPTIONS:
PRODUCT COLOR TEMP DRIVER TYPE MOUNTING
DZ40 50K – 5000K -‐STD 41K – 4100K (Special Order)
DV40-‐277 -‐ 100-‐277V, 40W Driver DV40-‐480S for 347-‐480V – a 480V Step Down Transformer Included 100-‐277V 40W Driver
H– Horizontal Mount V-‐ Vertical Mount FT – Flex Trim
DZ75 50K – 5000K -‐ STD 41K – 4100K (Special Order)
DV75-‐277 -‐ 100-‐277V, 75W Driver DV80-‐277D -‐ 100-‐277V, 75W Dimmable Driver DV100-‐480 -‐ 347-‐480V, 100W Driver (Tuned to 75W)
H– Horizontal Mount V-‐ Vertical Mount FT – Flex Trim
DZ130 50K – 5000K -‐ STD 41K – 4100K (Special Order)
DV150-‐277 -‐ 100-‐277V, 150W Driver DV150-‐277D -‐ 100-‐277V, 150W, Dimmable Driver DV150-‐480 – 347-‐480V, 150W Driver
H– Horizontal Mount V-‐ Vertical Mount FT – Flex Trim GP– General Plate
DZ260 Dual Head
50K – 5000K -‐ STD 41K – 4100K (Special Order)
DV150-‐277 -‐ 100-‐277V, 150W Driver (2 Drivers) DV150-‐277D -‐ 100-‐277V, 150W, Dimmable Driver (2 Drivers) DV150-‐480 – 347-‐480V, 150W Driver (2 Drivers)
CST– Custom Plate System
DZ360 Tri-‐Head
50K – 5000K -‐ STD 41K – 4100K (Special Order)
DV150-‐277 -‐ 100-‐277V, 150W Driver (3 Drivers) DV150-‐277D -‐ 100-‐277V, 150W, Dimmable Driver (3 Drivers) DV150-‐480 – 347-‐480V, 150W Driver (3 Drivers)
CST– Custom Plate System
SURGE PROTECTION PRODUCT SKU# DESCRIPTION
SP277 SP480
Surge Protector 20kA, 100-‐277V Surge Protector 20kA, 347-‐480V
OPTICS PRODUCT SKU# DEGREES
DZ40 45 -‐ 45° 30 -‐ 30°
DZ130
Type I Type2 Type 3 Type 4 Type 5 56 -‐ 56° Aisle
PHOTO CELL SENSOR
PRODUCT SKU# DESCRIPTION
PC120 PC277 PC120R
Photo Cell 120V Photo Cell 208-‐277V Photo Cell 120V Rotatable
DZ130 DV150-‐277D H
50K Color Temp
Driver Mounting
SKU:
Product
www.HiLumzUSA.com [email protected]
TOLL FREE: 1-‐888-‐347-‐0101 PHONE: 770-‐888-‐8338 FAX: 404-‐537-‐1900
Copyright © HiLumz® LLC 2014. All Rights Reserved. Product and company names mentioned herein may be trademarks of their respective owners. Product enhancements may result in specification changes without notice. Specifications are deemed accurate, but not guaranteed. Contact us for the most current information.
Single Head Mounting Instructions Included in Horizontal kit:
(1) Diamonz Light Head (1) Flex Bracket (1) 1/4"-‐20 Thread, 1/2" Nut
Vertical Kit includes the same as above with addition of a Y-‐Bracket
(1) Hose Clamp (1) Driver Plate (2) Self Drilling Screws to attach Driver to Driver Plate
Horizontal Installation – Easy as 1-2-3
1) The Diamonz Head’s Fan plate (Pic A) is designed with a slotted section that the Flex Bracket (Pic B) attached to with the ¼” nut. 2) The Flex Bracket is sent straight and is bent in the field by placing thumbs on each “Bend Point” and bending to 90 degrees as seen in
the same pic. Either attach the Diamonz head to the Flex Bracket or attach the Flex Bracket to the mogul base. 3) The Flex Bracket is secured to the mogul base with hose clamp. The Flex Bracket is designed with snap off section so that it can be
shortened for better flexibility in centering the head. Vertical Installation
Pic A Pic B Pic C
Bend Points
1) The Y-‐Bracket is attached to the sides of the Diamonz Head using the 1/4"-‐20 Thread, 1/2" length screws on the side of the unit.
2) The Flex Bracket is sent straight and is bent in the field by placing thumbs on each “Bend Point” and bending to 90 degrees as seen in the same pic. Either attach the Diamonz head to the Flex Bracket or attach the Flex Bracket to the mogul base.
3) The Flex Bracket is secured to the mogul base with hose clamp. The Flex Bracket is designed with snap off section so that it can be shortened for better flexibility in centering the head.
Snap off sections to shorten bracket.
www.HiLumzUSA.com [email protected]
TOLL FREE: 1-‐888-‐347-‐0101 PHONE: 770-‐888-‐8338 FAX: 404-‐537-‐1900
Copyright © HiLumz® LLC 2014. All Rights Reserved. Product and company names mentioned herein may be trademarks of their respective owners. Product enhancements may result in specification changes without notice. Specifications are deemed accurate, but not guaranteed. Contact us for the most current information.
Dual Head Mounting Instructions Included in Horizontal kit:
(1) Diamonz 2 Head Light Assembly (2) Drivers (1) Flex Bracket (2) Cable Connection
(1) Hose Clamp (2) Driver Plates (4) Self Drilling Screws to attach Drivers to Driver Plates
Horizontal Installation
Vertical Installation
1. The ballast is removed and the Driver plates are affixed to the
screw ports with screws or with 3M HVB tape provided. 2. The Diamonz Head’s center Bracket (Pic D) is designed with a
slotted section that the Flex Bracket (Pic B) attached to with the ¼” nut.
2) The Flex Bracket is delivered straight and is bent in the field by placing thumbs on each side of the “Bend Point” (Pic B) and bending to 90 degrees as seen in the same pic. Either attach the Diamonz head to the Flex Bracket or attach the Flex Bracket to the mogul base/
3) The Flex Bracket is secured to the mogul base (Pic C) with hose clamp. The Flex Bracket is designed with snap off section so that it can be shortened for better flexibility in centering the head. (Pic B)
4) Support cables are screwed into the sides (Pic X). The 3M HVB tape that are attached to the tabs is peeled back and then attached the interior sides of the fixture.
5)
Pic D
1) Same as above but loosen the nuts to center bracket and rotate to a vertical position and re-‐tighten nuts.
2) Attach Flex bracket to center hole.
www.HiLumzUSA.com [email protected]
TOLL FREE: 1-‐888-‐347-‐0101 PHONE: 770-‐888-‐8338 FAX: 404-‐537-‐1900
Copyright © HiLumz® LLC 2014. All Rights Reserved. Product and company names mentioned herein may be trademarks of their respective owners. Product enhancements may result in specification changes without notice. Specifications are deemed accurate, but not guaranteed. Contact us for the most current information.
Three Head Mounting Instructions Included in Horizontal kit:
(2) Diamonz 3 Head Light Assembly (3) Drivers (1) Flex Bracket (2) Cable Connectors (1) Y-‐Bracket
(1) Hose Clamp (3) Driver Plates (6) Self Drilling Screws to attach Drivers to Driver Plates
Vertical Kit includes the same as above with addition of a Y-‐Bracket
Horizontal Installation
Vertical Installation Vertical will be the similar to Dual Head.
3. The ballast is removed and the Driver plates are affixed to the
screw ports with screws or with 3M HVB tape provided. 4. The Diamonz Head’s center Bracket (Pic D) is designed with a
slotted section that the Flex Bracket (Pic B) attached to with the ¼” nut.
6) The Flex Bracket is sent straight and is bent in the field by placing thumbs on each “Bend Point” (Pic B) and bending to 90 degrees as seen in the same pic. Either attach the Diamonz head to the Flex Bracket or attach the Flex Bracket to the mogul base/
7) The Flex Bracket is secured to the mogul base (Pic C) with hose clamp. The Flex Bracket is designed with snap off section so that it can be shortened for better flexibility in centering the head. (Pic B)
8) Support cables are screwed into the sides (Pic X). The 3M HVB tape that are attached to the tabs is peeled back and then attached the interior sides of the fixture.
9)
Pic D
3) Same as above but loosen the nuts to center bracket and rotate to a vertical position and re-‐tighten nuts.
4) Attach Flex bracket to center hole.
www.HiLumzUSA.com [email protected]
TOLL FREE: 1-‐888-‐347-‐0101 PHONE: 770-‐888-‐8338 FAX: 404-‐537-‐1900
Copyright © HiLumz® LLC 2014. All Rights Reserved. Product and company names mentioned herein may be trademarks of their respective owners. Product enhancements may result in specification changes without notice. Specifications are deemed accurate, but not guaranteed. Contact us for the most current information.
RETROFIT MOUNTING Greater Flexibility For Your Diamonz® LED Retrofit Kits
Mounting Enhancements
You Spoke. We Listened. “Your 1st Generation Diamonz Retrofit Kits Are Good, But There’s Too Much Assembly Required in the Field.”
You Wanted Easier Assembly with Fewer Pieces.
2nd Generation Diamonz Retrofits Mounting – “Much Better!”
Horizontal Installation
1st Generation Diamonz Retrofit Kit Mounting
As you can see, this is a much easier assembly and the design provides greater flexibility to position the head for maximum light output! The fan plate offers two slots so the head can be moved up or down, if needed. Introducing…The Flex Mount™ System
With the newly designed fan plate, just attach the Flex Mount™ bracket with a single nut. Then, using a hose clamp secure around the mogul base. Done! The Flex Mount bracket is designed with snap off sections for better centering in the fixture. This provides a much more secure, solid installation than screwing into the mogul base.
www.HiLumzUSA.com [email protected]
TOLL FREE: 1-‐888-‐347-‐0101 PHONE: 770-‐888-‐8338 FAX: 404-‐537-‐1900
Copyright © HiLumz® LLC 2014. All Rights Reserved. Product and company names mentioned herein may be trademarks of their respective owners. Product enhancements may result in specification changes without notice. Specifications are deemed accurate, but not guaranteed. Contact us for the most current information.
Vertical Installation Uses a Y-bracket like in the 1st Generation Diamonz product that attaches directly to the side of the fan plate. No more L-brackets!
PRODUCT
SKU# DESCRIPTION H Horizontal Mount V Vertical Mount CP Custom Plate
H SKU:
Mounting
ORDERING OPTIONS: When placing an order, build your SKU code by selecting the various options in each column below. Use the numbers in bold as the numbers/characters to create the appropriate SKU code. See the following example.
Example: Horizontal Mount Option (added to the end of the SKU of the Retrofit Kit product chosen)