RENOVATION WORK FOR FLAT NO. 3-4 AND 5-6 … Granite frame for toilet door- Providing and laying pre...
Transcript of RENOVATION WORK FOR FLAT NO. 3-4 AND 5-6 … Granite frame for toilet door- Providing and laying pre...
PART - A DGM HOUSE (FLAT NO. 3-4 AND 5-6 ZONE I
AND ZONE II )
Sr. no. Details/ Description of items Unit Qty Rate Amt
1 RCC: Providing and laying cast in situ nominal mix M-25 grade
cement concrete of ratio 1:1:2 (Cement: Sand: Aggrigate), for
reinforced cement concrete work for Slabs, Suspended floors,
roofs, landings, balconies, canopy and access platform, Stairs
(waist slab), folded slab, inclined slab, using cement content as
per approved design mix, including pumping of concrete to site of
laying and the cost of centering, shuttering, deshuttering and
hacking of concrete after deshuttering. finishing and excluding
reinforcement, including admixtures in recommended proportions
as per IS: 9103 to accelerate, retard setting of concrete, improve
workability without impairing strength and durability as per
direction of Engineer-in-charge.The Mix design as per particular
specfications shall be got approved by Engineer-in-Charge before
execution of the item.The rate shall include cost of all specified
materials and operations at all levels and heights, including the
cost of centering, shuttering and including main reinforcement of
16mm dia bars and distribution steel of 10mm dia bars.Honey
combing if found after deshuttering then contractor has to finish
the same with cement sand mortar with ratio 1:3 at no extra
cost.(Note :- Cement content considered in this item is @ 340
kg/cum as per IS 456 table showing minimum cement content.
CUFT 20
2 Autoclaved areated blocks (100MM thk)- Providing and
laying autoclaved aerated[cellular] cement block masonry with
100/ 150/200/230/240 mm thk AAC Blocks in cement mortar
1:4[1cement ;4 coarse sand] including RCC Stiffners the rate
includes providing and placing in position 2 nos of 8mm dia ms
bars at every third course of masonry work racking of joints
scaffolding and curing etc completed as directed by Engineer-in-
charge.
SQFT 980
3 Internal plaster - Providing plaster in cement mortar in 1:3
with wall putty of Birla, JK Cement or aproved equivalent and
finishing to concrete or masonry surface in all position including
scaffolding and curing also providing chicken mesh at “V-
groove” joints at ceiling and cracks in wall plaster complete.
b) 20 mm thick two coats (Walls) SQFT 2200
RENOVATION WORK FOR FLAT NO. 3-4 AND 5-6 ZONE I AND ZONE II DGM'S HOUSE AND FLAT NO. 7-8
GUEST HOUSE IN BUILDING NO. 4, SBI OFFICE MADHUBAN PUNE.
A) CIVIL WORKS
Vastukala Design Build Solutions Pvt. Ltd. 1Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
4 Providing waterproof in WC and bath at flooring and 1' high of
dado including brick bat coba- Clean the RCC slab surface & wall
for treatment by removing dust, dirt and layers of concrete over the
surface. Identifying the cracks, construction joints & filling the same
with Polymer Modified Mortar using POLYALK EP (Sunanda
Speciality Coatings Pvt.Ltd. or approved equivalent ). (IS code -
2645 - 2003) Injection grouting shall be done with providing and
injection non shrink cementations grout by mixing – 2 pouches (330
gms. each) of “SUNPLEX” (Sunanda Speciality Coatings
Pvt.Ltd. or approved equivalent ) (IS code - 2645 - 2003) and 50
kgs of cement and sufficient water for flow ability, grouting the
same under pressure, complete. 24 hours after grouting is completed.
After completion of crackfilling & grouting ponding shall be done
for 3 days to ensure the success of pressure grouting, if there is no
leakages/ seepage/ dampness then only further activities shall be
started. Providing and applying three coats of “POLYALK WP”
(Sunanda Speciality Coatings Pvt.Ltd. or approved equivalent)
and cement in 1:1.25 ratio at an interval of 24 hours on the slab and
side walls upto 1 ft above slab level of toilet. Apply two coats and
cure the same and apply the third coat and while it is still wet and
tacky providing wet chat/dash coat of 1:4 cement mortar in 10-12
mm thickness. for application confirming to (IS code 1318 - 2000)
SQFT 630
Lay an average 2½” thick well soaked brick bat metal coba in
cement mortar 1:4 to proper level and slope as per instructions
adding “SUNPLEX” - 330 gms pouch (Sunanda Speciality
Coatings Pvt.Ltd. or equivalent ) per 50 Kg bag of cement to
the mortar mix. Fill up the brick joints and lay metal coba in C:M
1:4 adding “SUNPLEX”- 330 gms pouch (Sunanda Speciality
Coatings Pvt.Ltd. or equivalent ) or equivalent per 50 Kg bag
of cement and finished with chequered markings for further
provision of floor tiles. Rate to include for making border at
the junction of watta and wall plaster upto 1 ft above slab level,
ponding for seven days by closing the UPVC and soil outlets and
making watas etc. complete to the satisfaction of the EIC.
5 Ceramic tile flooring- Providing and laying ceramic tile
flooring (equivalent to Bell, Nitco, Johnson, Kajaria etc) of size
300 x 300 mm (Anti skid) conforming to IS:13712-2006, of
approved colour including cement float, filling the joints with
matching colour, with pigments added to white cement slurry
cleaning etc. complete. (Required size with approved design)
(Ceramic tiles of base rate 75 Rs/ Sqft)
SQFT 400
6 Ceramic tile Dado- Providing and fixing decorative ceramic
tiles including single coat plaster with waterproofing
compound(equivalent to Bell, Nitco, Johnson, Kajaria etc) of
size 300 mm x 600 mm (Including highlighter tiles) and above 5
to 6 mm thick for dado and skirting in required position fixed
on single coat plaster of cement mortar 1:4, neat cement paste,
filling joints with neat cement float, filling joints with neat
cement slurry, curing and cleaning complete. (required size with
approved design) (Decorative Ceramic tiles of base rate 55-65
Rs/ Sqft)
SQFT 1380
Vastukala Design Build Solutions Pvt. Ltd. 2Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
7 Granite frame for toilet door- Providing and laying pre
polished granite frame of 150mm to 175mm wide for toilet
doors in stepped manner of 20 mm thickness, size and colour
including cutting to the required size, polished edges from inside
toilet, photo frame of 2.5" confirming to (IS code 14223(1) - 1995
) wide from outside, laying jointing and grouting the joints with
cement slurry of required colour made of white cement and colour
on a bed of 1:4 cement mortar all labour & materials etc.
complete. ( Tiles from inside shall be flushed with grainte) (
Basic rate of granite - 165 - 180 Rs/Sq. Ft)
RFT 170
8 Internal wall paint- Providing and applying plastic emulsion
paint conforming to IS:15489-2004 part I of superior quality of
approved make, colour and shade to the old & new surfaces in
two coats over primers, including scaffolding, preparing the
surfaces to receive the paint by removing old paint, thoroughly
cleaning oil, grease dirt and other foreign matter with brushing,
fine fire steel wool, sand paper and applying putty of approved
make etc. complete.(including primer)
SQFT 7000
9 Synthetic enamel paint on metal - Providing and applying two
coats of synthetic enamel paint of approved colour to new/old
structural steel work and wood work in buildings and
workshops including scaffolding if necessary, cleaning and
preparing surfaces by solvent, degreasing and derusting by
manual scrapping/mechanically by sand blasting/shot blasting
flame cleaning/by chemical methods, scaffolding etc. complete.
(including primer coat)
SQFT 500
10 Texture paint - Providing & applying painting two or more coats
of plastic/acrylic light textured emulision paint of approved shade
& manufactured by spectrum or asian spl paint equivalent to
walls after scrapping the original surface rubbing with sand paper
of zero size for smooth surface,two coats of putty & two coats of
emulsion paint of approved colour & make successively after
drying each coat & finishing with sponge roller(matt finish) over
a coat of approved primer with necessary scaffolding
etc,complete as per specification.
SQFT 600
11 Providing and laying 10mm thick nano finish colour Vitrified
tiles johnson ,Nitco , kajaria or approved equivalent of 600 mm x
600mm in flooring, skirting, dado and in other places as shown in
tiles laid on 12mm thick cement mortar bed or backing of mix
1:3, with joints properly aligned, filled with white cement slurry
with matching pigment, OR LATICRETE PLATINUM with
joints properly aligned filled with Laticrete permacolor grout of
colour to match tile at all levels and locations to different patterns
as per specifications ,and direction of the Engineer all complete
(glossy or mat finish as required). Tiles shall be bevelled at the
vertical corner joints and horizontal edge joints. Top of
skirting/dado shall
be finished smooth to line and level.
Flooring &Skirting tile basic rate 80 rs per sq.ft
Cement - Ultratech / Ambuja / ACC cement, Jointing same colour
grout material
SQFT 3200
Vastukala Design Build Solutions Pvt. Ltd. 3Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
12 Providing & applying Plaster of Paris on walls in line & level,
and in right angle by making the existing surface rough enough to
take the plaster material. The finished surface shall be smooth
and without any undulations.
SQFT 600
13 Sliding Window with mosquito net and granite frame -
Providing and fixing in position aluminium windows and
ventilators as per aprroved drawings with sliding and shutters
using three track window frame of size 92 x 31.75 mm bottom
section 1.3 mm thick, weight 1.07 kg/m; sides and top sections
1.3 mm, thick, weight 0.933 kg/m. shutter frame section
comprising top and bottom section of size 40 x 18 mm, wall
thickness 1.25. weight 0.417 kg/m. shutter side outer 40 x 18
mm. wall thickness 1.25mm, weight 0.417kg/m, shutter interlock
section 40 x 26.7mm, wall thickness 1.1mm, weight 0.469 kg/m,
the shutters mounted on nylon rollerswith approved quality of
fixtures such as aluminium handles, tower bolt etc. providing and
fixing 5mm thick plain glass for shutters fitted with rubber
bedding all aluminium sections including cutting to required
length, joints mitred subdividing the frame tenonned and rivetted
, in the assembled frame, stimmened with end clips for corners,
angles etc., and fixed to the walls, lintels, floor beams, sill as the
case may be, with necessary steel screws, raul plug or teak wood
gaatties including cutting masnory or concrete and making good
the original surface using cement mortar
SQFT 450
Granite frame (Window frame) - Providing and laying pre
polished double stepped granite frame of minimum 18 mm
thickness, with photo frame from inside of 150mm wide, size and
colour including cutting to the required size, laying jointing and
grouting the joints with cement slurry of required colour made of
white cement and colour on a bed of 1:4 cement mortar all labour
& materials etc. complete. Rate to be include moulding and edge
polish.(Granite basic rate: 1100 Rs/Sqm) (Mode of
measurement - length x height)
Window mosquito net-Providing and fixing aluminium sliding
shutter with G.I mosquito net, silicon Sealant / Neoprene
gasket etc. complete. The thickness of Aluminium Frame to be
1.2 to 1.5 mm thick. Aluminium shutters (top, bottom, side and
intermediate sections) to be 40mm x 18mm x 1.5mm thick.with
approved type of locking arrangement, handles and other fixtures
including fixing, cleaning polishing the aluminium section with
petrol and / or other agents as specified by the manufacturers etc.
Complete. (Mode of measurement - length x height)
14 Providing and fixing M.S. grill work to windows or openings
made out of 10 mm square bars and MS flats of 25 mm x 4 mm
welded to L angle frame made out of 25 X 25 X 4 mm including
bracket of "L-angle" at bottom of M.S. grill with necessary
holdfast one coat of primer and two coats of synthetic enamel
paint (IS 2932 - 2003) etc complete including welding as
necessory at all heights & levels including scaffolding if
necessary.
SQFT 500
Vastukala Design Build Solutions Pvt. Ltd. 4Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
15 Aluminium louvered window with granite frame and MS
grill - Providing and fixing in position aluminum louvered
window with anodised aluminum frame of approved make and of
size 40mm x 20mm x 2.0mm (wt. 0.605 kg/Rm) including
adjustable aluminum frame, 4 to 6mm thk. frosted glass, fixtures
and fastenings etc. complete as directed by by Engineer In
Charge. (Mode of measurement - length x height)
SQFT 70
Granite frame (Window frame) - Providing and laying pre
polished double stepped granite frame of minimum 18 mm
thickness, with photo frame from inside of 150mm wide, size and
colour including cutting to the required size, laying jointing and
grouting the joints with cement slurry of required colour made of
white cement and colour on a bed of 1:4 cement mortar all labour
& materials etc. complete. Rate to be include moulding and edge
polish.(Granite basic rate: 1100 Rs/Sqm)
16 Granite Kitchen Counter-Providing and laying granite kitchen
counter of 750mm width (clear) and at 750mm height (top)
above FFL of approved 20 mm thick granite fixed on 40mm thick
horizontal kadappa with 1:4 cement mortar and vertical kadappa
supports of 25 mm thick as required. A 75- 100 mm high granite
facia should be provided with bull nosed edges, the top of facia to
be 12mm above the granite platform. Rate shall be inclusive of
making cut out sand polishing the edges for S.S. Sink as per size
required.Inclusive of 32mm dia down take pipe as required up to
nahani trap. ( Basic rate of granite - 1000 - 1350 Rs/Sq. m)
(Mode of measurement - length x width )
RFT 34
17 PVC doors- Providing and fixing PVC Door of required size
and colour along with all accessories like Hinges, Tower Bolts,
Aldrop, Screw, Handel, tadi etc. hollow section of size
150mmX31mmX1.2mm UPVC profile with bordar of "U" hollow
size section of size 35mmX35mmX2mm the corner will be joined
with tough plastic of "L" angles at all corners with chromium
plated fixtures and fasteners stainless screws etc. complete. The
PVC door to have wood grain type finish to match the guest room
door laminate. Spec: (As directed by engineer in charge)
NOS. 8
18 Flush Door - Providing and fixing solid core flush door shutter
commercial in single leaf 32mm thick without ventilator
commercial type of exterior grade as per detailed drawings. Rate
shall be inclusive of all necessary approved fittings like hinges,
locks, 300mm long SS brushed finish handles,tower bolts, locks
and any necessary hardware items.SS handles to be provided on
both sides and finishing with decorative laminate 1mm thick on
both sides as approved by client or Architect. (Mode of
measurment - length x Height)
NOS. 20
Vastukala Design Build Solutions Pvt. Ltd. 5Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
19 Gypsum board false ceiling SQFT 1800
Providing and fixing in position Gypsum Board False Ceiling
including Two coats of Plastic emulsion Paint of appd.quality as
per manufacturer's specifications and instructions with 12.5 mm
thick `Gypboard' Screw-fixed to the underside Of suspended G.I.
grid. G.I. grid should be Constructed and suspended from the
main ceiling as per manufacturer's instructions and as per
specifications using Original Co. Specified Framework Sections
G.I.24 gauge The Gypboard should be fixed to G.I. grid with 25
mm long Drawali Screws. The `Gypboard ' to be used should be
12.5mm thick tapered edge boards. The boards should Be taped
and filled from underside to give smooth, seamless ceiling. The
rate should include necessary additional ceiling sections and
intermediate channels openings for light fixtures, A.C. ducts,
vertical drops, offsets. etc.
Additional Intermediate channels should be fixed to strap
hangers for additional support to prevent strap hangers from
buckling/swaying at every 1200 mm. Item to be completed in all
respect including necessary sleeves for ducts finishing of joints
cut outs supports for A.C. grills, light fixtures, speakers
etc.Make: Gypusm board-India Gypsum. Panint-Asian/ ICI
The rate should include necessary additional ceiling sections and
intermediate channels openings for light fixtures, A.C. ducts,
vertical drops, offsets.and with two coats of putty, two coats of
approved primer, and three coats of approved lustre paint
19a Specification same as above for Vertical band of Gypsum 4" -6"
BAND
RFT 690
20 AC ply Boxing: Providing and fixing 18 mm thk Marine plywood
boxing conforming to IS710 on wooden / GI frame for covering
AC pipes. The boxing to be finished with gypsum board and 2
coats of plastic emulsion paint
SQFT 300
21 Providing & fixing 2' wide Granite Base Wash Basin Counter for
passage. The basic cost of Granite 200/- per sft
RFT 50
22 Supplying & fixing approved colors/ design wall paper as per site
requirement.
SQFT 1000
1 15/20/25mm CPVC Pipes- Providing and fixing Chlorinated
Polyvinyl Chloride (CPVC) pipes confirming to IS 15778-2007
having 15/20/25 mm nominal outer dia Pipes for internal water
circulation. There are two types of water supply connection one
from 'PMC' and one from well water in 6 flats at all levels and
heights. item includes providing both the water supply
connections in all toilets and kitchen. for flushing in toilets only
provide well water connection with neccessary fittings. the
contractor should visit the site and understand the scope and
extent of piping before filling the tender
LS
2 40mm dia UPVC pipe for basin drainage- Providing and fixing
leak proof and frost proof ASTMD (UPVC) Pipes of 40mm
dia having a wall thickness 5.08mm schedule 80 pipes (pressure
rating) for normal water supply and painting the pipe in white oil
paint etc. complete. Spec: (As directed by Engineer in charge))
RFT 88
TOTAL CIVIL WORK COST (A)
B) PLUMBING WORKS
Vastukala Design Build Solutions Pvt. Ltd. 6Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
3 110MM UPVC soil pipe: Providing, fitting and laying UPVC
soil pipe Confirming to IS 13592 - B type, including vent pipe
with all required C.I specials, plugs, clamps etc., of approved
Neco make(red color) confirming to IS 3989 , including,
excavation & back filling, jointing with drip seal all complete as
per specifications and direction of Engineer.
RFT 10
4 Concealed stopcock- Supply & Fixing of CP brass Concealed
stopcock with regular body of standard design and of approved
make confirming to ISI. (Jaquar continental series or
equivalent)Concealed stopcock- Supply & Fixing of CP brass
Concealed stopcock with regular body of standard design and
of approved make confirming to ISI. (Jaquar continental series
or equivalent)
NOS. 30
5 Angle stopcock- Supply & Fixing of CP brass Angle stopcock
of standard design and of approved make confirming to
ISI.(Jaquar continental series cat no. 055)Angle stopcock-
Supply & Fixing of CP brass Angle stopcock of standard
design and of approved make confirming to ISI.(Jaquar
continental series cat no. 055)
NOS. 10
6 Bib Tap- Providing & fixing in position CP brass two way
bib tap approved make full turn type, with heavy casted CP
brass wall flange. (Jaquar continental series or
equivalent)Bib Tap- Providing & fixing in position CP brass
two way bib tap approved make full turn type, with heavy
casted CP brass wall flange. (Jaquar continental series or
equivalent)
NOS. 28
7 Health faucet- Providing & fixing stealth faucet jet spray of
approved Jaguar or equivalent make including necessary
socket/union etc. complete as directed. (As directed by Engineer
in charge)Health faucet - Providing & fixing stealth faucet jet
spray of approved Jaguar or equivalent make including necessary
socket/union etc. complete as directed. (As directed by Engineer
in charge)
NOS. 8
8 Hand shower- Providing & fixing Handshower of approved
make including necessary fittings etc. complete. (Jaquar
continental series or equivalent)Hand shower- Providing &
fixing Handshower of approved make including necessary
fittings etc. complete. (Jaquar continental series or equivalent)
NOS. 8
9 Soap Dish holder- Providing & fixing in position Soap Dish
holder of standard make for complete finish item of work.
(Jaquar continental series or equivalent)Soap Dish holder-
Providing & fixing in position Soap Dish holder of standard
make for complete finish item of work. (Jaquar continental
series or equivalent)
NOS. 10
10 Toilet paper Holder- Supply & Fixing of Toilet paper holder
with paper of standard make for complete finish item of work.
(Jaquar continental series or equivalent)Toilet paper Holder-
Supply & Fixing of Toilet paper holder with paper of standard
make for complete finish item of work. (Jaquar continental
series or equivalent)
NOS. 8
11 Towel rail- Supply & Fixing single towel rail of 600 mm long
with standard make for complete finish item of work. (Jaquar
continental series or equivalent)Towel rail- Supply & Fixing
single towel rail of 600 mm long with standard make for
complete finish item of work. (Jaquar continental series or
equivalent)
NOS. 10
Vastukala Design Build Solutions Pvt. Ltd. 7Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
12 Mirror- Providing and fixing Box type mirror including
necessory fittings of size 450mm x400 mm single door. Note:
Prior approval of sample and brand by Incharge Engineer is
necessary before use.Mirror- Providing and fixing Box type
mirror including necessory fittings of size 450mm x400 mm
single door. Note: Prior approval of sample and brand by
Incharge Engineer is necessary before use.
NOS. 10
13 Wash Basin- Providing and fixing White Vitreous China
wash basin (Parryware - Kingsmere 0414) size 630 x 450 mm
with C.I. brackets, with bottle trap of approved make, 32 mm
C.P. brass waste of standard pattern, including painting of fittings
and brackets, cutting and making good the walls wherever
require. Wash Basin- Providing and fixing White Vitreous
China wash basin (Parryware - Kingsmere 0414) size 630 x
450 mm with C.I. brackets, with bottle trap of approved make, 32
mm C.P. brass waste of standard pattern, including painting of
fittings and brackets, cutting and making good the walls wherever
require.
NOS. 10
14 Overhead Shower- Providing and fixing Overhead shower
(ABS Chrome Plated) with Rubit cleaning system of approved
make including necessory fittings etc. complete. (Jaquar
continental series or equivalent)Overhead Shower- Providing
and fixing Overhead shower (ABS Chrome Plated) with
Rubit cleaning system of approved make including necessory
fittings etc. complete. (Jaquar continental series or equivalent)
NOS. 8
15 Napkin Ring Square- Providing and fixing SS Napkin ring
square of approved make including necessory fittings etc.
complete. (Jaquar continental series or equivalent)Napkin
Ring Square- Providing and fixing SS Napkin ring square of
approved make including necessory fittings etc. complete.
(Jaquar continental series or equivalent)
NOS. 10
16 European type commode- Providing and fixing European
type commode with Ceramic cistern (Parryware - Flair-
C0237/281/C2067/C0757) conforming to IS:2556 -1994 (Part-
II) latest edition with PVC double seat cover commode or
equivalent including outlet, inter connections through walls
including all fittings etc. complete. Note: Prior approval of
sample and brand by Incharge Engineer is necessary before
use.
NOS. 6
17 Indian type water closet: Providing and fixing vitreous China
white glazed Indian type water closet of superior quality
580mmX480MM size Orissa pan(PARRYWARE make, model-
Orissa 580 with ISI-mark) with 'P' or 'S' trap, vent hole, with low
level PVC cistern of 10 liters capacity of "PARRYWARE make”,
syphon & standard flush fittings, CP connecting flush pipe,
15mm CP bras concealed stop cock deluxe type, 15mm dia
flexible PVC inlet water connection, all fittings Complete
including all materials etc complete
NOS. 2
Vastukala Design Build Solutions Pvt. Ltd. 8Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
18 Providing and Fixing Steel Sink (Nirali - Eureka delux small -
satin finish) of size 53.3 X 35.5 X 20 cm to the Kitchen
platform including UPVC waste coupling pipe and coupling,
necessory fittings & making good the damaged surface etc.
complete. Note: Prior approval of sample and brand by
Incharge Engineer is necessary before use.
NOS. 2
19 Wall Mixer- Providing and fixing Wall Mixer with provision
for overhead Shower and Tel. Shower with 115mm long bend
pipe and wall Flange of approved make including necessory
fittings etc. complete. (Jaquar continental series or
equivalent)
NOS. 8
20 Piller Cock- Providing and fixing 15mm diameter Piller cock
P.V.C. polymer scratch resistant, anti-static with guarantee
against any manufacturing defect including socket, union nuts
etc. complete. Spec. (As directed by Engineer in Charge)
NOS. 10
21 Kitchen 2 way sink cock with Aquaguard arrangement-
Providing and fixing kitchen sink cock (wall mounted) with
swinging casted spout of approved make including necessory
fittings etc. complete. (Jaquar continental series or
equivalent)
NOS. 2
22 Nahani Trap- Providing and fixing 100 x 75mm HSI
floor/Nahani trap with CP hinged heavy brass grating to be
fixed with M15 and make water tight.
NOS. 20
1 Trolley baskets- Providing and fixing Stainless steel baskets of
S.S. 304 grade of approved size with 2mm thk SS sheet & frames
with including necessory fitting etc. complete.
Type 1 - (520 x 535 x 100) NOS. 4
Type 2 - (520 x 535 x 150) NOS. 4
Type 3 - (520 x 535 x 350) NOS. 4
Type 4 - (520 x 535 x 300) NOS.
2 Shutter front- Providing and fixing 18 mm thk Marine
plywood conforming to IS710 shutter front with ply frame,
skirting. Shutter front shall be hinged to the frame work and
finished with 1 mm thk laminate of approved shade from outside,
0.8 mm white laminate from inside and 2 mm thk PVC edges
binding from all sides. Rate shall be inclusive of all necessary
approved fittings like hinges, magnet, handle, and any necessary
hardware items.
SQFT 90
3 Drawer front- Providing and fixing 18 mm thk Marine
plywood conforming to IS710 drawer front with ply frame,
skirting. Drawer front shall be fixed with heavy duty sliders to the
frame work and finished with 1 mm thk laminate of approved
shade from outside, 0.8 mm white laminate from inside and 2 mm
thk PVC edges binding from all sides. Rate shall be inclusive of
all necessary approved fittings like heavy duty sliders, ballcatch,
handle, slow closer and any necessary hardware items. (Designer
laminate base rate of 1350 Rs/ Sq.ft)
SQFT 50
TOTAL PLUMBING WORK COST (B)
C) FURNITURE WORK
Vastukala Design Build Solutions Pvt. Ltd. 9Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
4 Storage Unit- Providing and fixing storage units of full height as
per drawng. They shall consist of 18mm thk.marine. ply top,
sides,back, bottom, shelves and shutters. The bottom of the
storages shall be at 3” from FFL. The top of storages shall touch
the false ceiling level or 7'-0" ht. The shutter with box type higes
of approved make & steam beach lipping finished with melamine
with approved laminate on all the shutter edges. Division of the
shutters shall be made equally according to the length of the
storages (as approved by Bank/ architect). All the external
surfaces shall be finished with 1.0mm thick decorativeLaminate
(suede finish) of approved make.
SQFT 450
18mm thk. Ply shelves removable type supported on side steam
beach wood battens on both sides at 16” interval ( approximately
/ divided equally) shall be provided. All inner surfaces shall be
finished with 0.8 mm white laminate including the shutters . Rate
shall be inclusive of all necessary approved fittings like hinges,
locks, 150mm long SS brushed finish handles,tower bolts, locks
and any necessary hardware items. The top ply edge should be
fitted with 19mm x 7mm size steam beach moulding finished
with melamine. Wherever the plywood comes in contact with
the wall Black Japan shall be applied on backside of the
plywood.
5 Providing & fixing shutters below Wash basin counter with
19mm thick marine ply wood & approved 1mm lamination &
hardware fittings.
SQFT 50
6 Providing and fixing curtain with stichng of approved shade (
Basic cost of curtain - Rs. 350-375/-per metre)
SQFT 800
7 Providing and fixing curtain rod RFT 340
1 Buy Back existing windows with MS grill ( the
contractor to give rebate )
Contractor to visit the flats to check the quantity and
quality of existing furniture,etc to buy back. The
furniture,etc. shall be taken back on "As it is where it
is basis" After removing the window from the location
contractor has to finish the edges of the window
opening to fix the new window.
Window – 6'-0” x 4'-0” LS
Window – 3'-0” x 4'-0”2 Removing tiles- Removing any type of tiled flooring/ dado
with plaster in toilet walls and kitchen including levelling the
surface, cleaning the site including sorting out serviceable tiles
and carting away debris to approved lcoation of authority having
jurisdiction. Spec: (As directed by engineer in charge)
LS
3 Removing existing platform with partion in kitchen-Removing
existing kitchen platform and plastering the surface including
carting away debris to approved lcoation of authority having
jurisdiction. Spec: (As directed by engineer in charge)
LS
4 Demolition of existing brick wall-Dismantling 6” thk, brick
wall carefully by using chisel to cut & making good wall edges
with 1:4 cement plaster including removal of debris from site.
LS
D) REBATE ITEMS
TOTAL DISMANTLING COST (D)
FURNITURE WORK COST (C )
Vastukala Design Build Solutions Pvt. Ltd. 10Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
PART - B GUEST HOUSE (FLAT NO. 7-8)
Sr. no. Details/ Description of items Unit Qty Rate Amt
1 RCC: Providing and laying cast in situ nominal mix M-25 grade
cement concrete of ratio 1:1:2 (Cement: Sand: Aggrigate), for
reinforced cement concrete work for Slabs, Suspended floors,
roofs, landings, balconies, canopy and access platform, Stairs
(waist slab), folded slab, inclined slab, using cement content as
per approved design mix, including pumping of concrete to site of
laying and the cost of centering, shuttering, deshuttering and
hacking of concrete after deshuttering. finishing and excluding
reinforcement, including admixtures in recommended proportions
as per IS: 9103 to accelerate, retard setting of concrete, improve
workability without impairing strength and durability as per
direction of Engineer-in-charge.The Mix design as per particular
specfications shall be got approved by Engineer-in-Charge before
execution of the item.The rate shall include cost of all specified
materials and operations at all levels and heights, including the
cost of centering, shuttering and including main reinforcement of
16mm dia bars and distribution steel of 10mm dia bars.Honey
combing if found after deshuttering then contractor has to finish
the same with cement sand mortar with ratio 1:3 at no extra
cost.(Note :- Cement content considered in this item is @ 340
kg/cum as per IS 456 table showing minimum cement content.
CUFT 10
2 Autoclaved areated blocks (100MM thk)- Providing and
laying autoclaved aerated[cellular] cement block masonry with
100/ 150/200/230/240 mm thk AAC Blocks in cement mortar
1:4[1cement ;4 coarse sand] including RCC Stiffners the rate
includes providing and placing in position 2 nos of 8mm dia ms
bars at every third course of masonry work racking of joints
scaffolding and curing etc completed as directed by Engineer-in-
charge.
SQFT 490
4 Internal plaster - Providing plaster in cement mortar in 1:4 for
walls finished with wall putty of Birla, JK Cement or aproved
equivalent and finishing to concrete or masonry surface in all
position including scaffolding and curing also providing chicken
mesh at “V-groove” joints at ceiling and cracks in wall plaster
complete.
b) 12-15 mm thick single coat (Walls) finished with putty SQFT 1100
A) CIVIL WORKS
TOTAL OF PART - A (A+B+C+D)
Vastukala Design Build Solutions Pvt. Ltd. 11Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
5 Providing waterproof in WC and bath at flooring and 1' high of
dado including brick bat coba- Clean the RCC slab surface & wall
for treatment by removing dust, dirt and layers of concrete over the
surface. Identifying the cracks, construction joints & filling the same
with Polymer Modified Mortar using POLYALK EP (Sunanda
Speciality Coatings Pvt.Ltd. or approved equivalent ). (IS code -
2645 - 2003) Injection grouting shall be done with providing and
injection non shrink cementations grout by mixing – 2 pouches (330
gms. each) of “SUNPLEX” (Sunanda Speciality Coatings
Pvt.Ltd. or approved equivalent ) (IS code - 2645 - 2003) and 50
kgs of cement and sufficient water for flow ability, grouting the
same under pressure, complete. 24 hours after grouting is completed.
After completion of crackfilling & grouting ponding shall be done
for 3 days to ensure the success of pressure grouting, if there is no
leakages/ seepage/ dampness then only further activities shall be
started. Providing and applying three coats of “POLYALK WP”
(Sunanda Speciality Coatings Pvt.Ltd. or approved equivalent)
and cement in 1:1.25 ratio at an interval of 24 hours on the slab and
side walls upto 1 ft above slab level of toilet. Apply two coats and
cure the same and apply the third coat and while it is still wet and
tacky providing wet chat/dash coat of 1:4 cement mortar in 10-12
mm thickness. for application confirming to (IS code 1318 - 2000)
SQFT 385
Lay an average 2½” thick well soaked brick bat metal coba in
cement mortar 1:4 to proper level and slope as per instructions
adding “SUNPLEX” - 330 gms pouch (Sunanda Speciality
Coatings Pvt.Ltd. or equivalent ) per 50 Kg bag of cement to
the mortar mix. Fill up the brick joints and lay metal coba in C:M
1:4 adding “SUNPLEX”- 330 gms pouch (Sunanda Speciality
Coatings Pvt.Ltd. or equivalent ) or equivalent per 50 Kg bag
of cement and finished with chequered markings for further
provision of floor tiles. Rate to include for making border at
the junction of watta and wall plaster upto 1 ft above slab level,
ponding for seven days by closing the UPVC and soil outlets and
making watas etc. complete to the satisfaction of the EIC.
6 Ceramic tile flooring- Providing and laying ceramic tile
flooring (equivalent to Bell, Nitco, Johnson, Kajaria etc) of size
300 x 300 mm (Anti skid) conforming to IS:13712-2006, of
approved colour including cement float, filling the joints with
matching colour, with pigments added to white cement slurry
cleaning etc. complete. (Required size with approved design)
(Ceramic tiles of base rate 75 Rs/ Sqft)
SQFT 235
7 Ceramic tile Dado- Providing and fixing decorative ceramic
tiles including single coat plaster with waterproofing
compound(equivalent to Bell, Nitco, Johnson, Kajaria etc) of
size 300 mm x 600 mm (Including highlighter tiles) and above 5
to 6 mm thick for dado and skirting in required position fixed
on single coat plaster of cement mortar 1:4, neat cement paste,
filling joints with neat cement float, filling joints with neat
cement slurry, curing and cleaning complete. (required size with
approved design) (Decorative Ceramic tiles of base rate 55-65
Rs/ Sqft)
SQFT 940
Vastukala Design Build Solutions Pvt. Ltd. 12Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
8 Granite frame for toilet door- Providing and laying pre
polished granite frame of 150mm to 175mm wide for toilet
doors in stepped manner of 20 mm thickness, size and colour
including cutting to the required size, polished edges from inside
toilet, photo frame of 2.5" confirming to (IS code 14223(1) - 1995
) wide from outside, laying jointing and grouting the joints with
cement slurry of required colour made of white cement and colour
on a bed of 1:4 cement mortar all labour & materials etc.
complete. ( Tiles from inside shall be flushed with grainte) (
Basic rate of granite - 165 - 180 Rs/Sq. Ft)
RFT 85
9 Internal wall paint- Providing and applying plastic emulsion
paint conforming to IS:15489-2004 part I of superior quality of
approved make, colour and shade to the old & new surfaces in
two coats over primers, including scaffolding, preparing the
surfaces to receive the paint by removing old paint, thoroughly
cleaning oil, grease dirt and other foreign matter with brushing,
fine fire steel wool, sand paper and applying putty of approved
make etc. complete.(including primer)
SQFT 3500
10 Synthetic enamel paint on metal - Providing and applying two
coats of synthetic enamel paint of approved colour to new/old
structural steel work and wood work in buildings and
workshops including scaffolding if necessary, cleaning and
preparing surfaces by solvent, degreasing and derusting by
manual scrapping/mechanically by sand blasting/shot blasting
flame cleaning/by chemical methods, scaffolding etc. complete.
(including primer coat)
SQFT 250
11 Texture paint - Providing & applying painting two or more coats
of plastic/acrylic light textured emulision paint of approved shade
& manufactured by spectrum or asian spl paint equivalent to
walls after scrapping the original surface rubbing with sand paper
of zero size for smooth surface,two coats of putty & two coats of
emulsion paint of approved colour & make successively after
drying each coat & finishing with sponge roller(matt finish) over
a coat of approved primer with necessary scaffolding
etc,complete as per specification.
SQFT 300
12 Providing and laying 10mm thick nano finish colour Vitrified
tiles johnson ,Nitco , kajaria or approved equivalent of 600 mm x
600mm in flooring, skirting, dado and in other places as shown in
tiles laid on 12mm thick cement mortar bed or backing of mix
1:3, with joints properly aligned, filled with white cement slurry
with matching pigment, OR LATICRETE PLATINUM with
joints properly aligned filled with Laticrete permacolor grout of
colour to match tile at all levels and locations to different patterns
as per specifications ,and direction of the Engineer all complete
(glossy or mat finish as required). Tiles shall be bevelled at the
vertical corner joints and horizontal edge joints. Top of
skirting/dado shall
be finished smooth to line and level.
Flooring &Skirting tile basic rate 80 rs per sq.ft
Cement - Ultratech / Ambuja / ACC cement, Jointing same colour
grout material
SQFT 1880
Vastukala Design Build Solutions Pvt. Ltd. 13Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
13 Providing & applying Plaster of Paris on walls in line & level,
and in right angle by making the existing surface rough enough to
take the plaster material. The finished surface shall be smooth
and without any undulations.
SQFT 1000
14 Sliding Window with mosquito net and MS grill including
granite frame -Providing and fixing in position aluminium
windows and ventilators as per aprroved drawings with sliding
and shutters using three track window frame of size 92 x 31.75
mm bottom section 1.3 mm thick, weight 1.07 kg/m; sides and
top sections 1.3 mm, thick, weight 0.933 kg/m. shutter frame
section comprising top and bottom section of size 40 x 18 mm,
wall thickness 1.25. weight 0.417 kg/m. shutter side outer 40 x
18 mm. wall thickness 1.25mm, weight 0.417kg/m, shutter
interlock section 40 x 26.7mm, wall thickness 1.1mm, weight
0.469 kg/m, the shutters mounted on nylon rollerswith approved
quality of fixtures such as aluminium handles, tower bolt etc.
providing and fixing 5mm thick plain glass for shutters fitted
with rubber bedding all aluminium sections including cutting to
required length, joints mitred subdividing the frame tenonned and
rivetted , in the assembled frame, stimmened with end clips for
corners, angles etc., and fixed to the walls, lintels, floor beams,
sill as the case may be, with necessary steel screws, raul plug or
teak wood gaatties including cutting masnory or concrete and
making good the original surface using cement mortar
SQFT 225.00
Granite frame (Window frame) - Providing and laying pre
polished double stepped granite frame of minimum 18 mm
thickness, with photo frame from inside of 150mm wide, size and
colour including cutting to the required size, laying jointing and
grouting the joints with cement slurry of required colour made of
white cement and colour on a bed of 1:4 cement mortar all labour
& materials etc. complete. Rate to be include moulding and edge
polish.(Granite basic rate: 1100 Rs/Sqm) (Mode of
measurement - length x height)
Window mosquito net-Providing and fixing aluminium sliding
shutter with G.I mosquito net, silicon Sealant / Neoprene
gasket etc. complete. The thickness of Aluminium Frame to be
1.2 to 1.5 mm thick. Aluminium shutters (top, bottom, side and
intermediate sections) to be 40mm x 18mm x 1.5mm thick.with
approved type of locking arrangement, handles and other fixtures
including fixing, cleaning polishing the aluminium section with
petrol and / or other agents as specified by the manufacturers etc.
Complete. (Mode of measurement - length x height)
Providing and fixing M.S. grill work to windows or openings
made out of 10 mm square bars and MS flats of 25 mm x 4 mm
welded to L angle frame made out of 25 X 25 X 4 mm including
bracket of "L-angle" at bottom of M.S. grill with necessary
holdfast one coat of primer and two coats of synthetic enamel
paint (IS 2932 - 2003) etc complete including welding as
necessory at all heights & levels including scaffolding if
necessary.
Vastukala Design Build Solutions Pvt. Ltd. 14Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
15 Aluminium louvered window with granite frame and MS
grill - Providing and fixing in position aluminum louvered
window with anodised aluminum frame of approved make and of
size 40mm x 20mm x 2.0mm (wt. 0.605 kg/Rm) including
adjustable aluminum frame, 4 to 6mm thk. frosted glass, fixtures
and fastenings etc. complete as directed by by Engineer In
Charge. (Mode of measurement - length x height)
SQFT 35.00
Granite frame (Window frame) - Providing and laying pre
polished double stepped granite frame of minimum 18 mm
thickness, with photo frame from inside of 150mm wide, size and
colour including cutting to the required size, laying jointing and
grouting the joints with cement slurry of required colour made of
white cement and colour on a bed of 1:4 cement mortar all labour
& materials etc. complete. Rate to be include moulding and edge
polish.(Granite basic rate: 1100 Rs/Sqm)
Providing and fixing M.S. grill work to windows or openings
made out of 10 mm square bars and MS flats of 25 mm x 4 mm
welded to L angle frame made out of 25 X 25 X 4 mm including
bracket of "L-angle" at bottom of M.S. grill with necessary
holdfast one coat of primer and two coats of synthetic enamel
paint (IS 2932 - 2003) etc complete including welding as
necessory at all heights & levels including scaffolding if
necessary.
16 GRANITE KITCHEN COUNTER-Providing and laying granite
kitchen counter of 750mm width (clear) and at 750mm height
(top) above FFL of approved 20 mm thick granite fixed on 40mm
thick horizontal kadappa with 1:4 cement mortar and vertical
kadappa supports of 25 mm thick as required. A 75- 100 mm
high granite facia should be provided with bull nosed edges, the
top of facia to be 12mm above the granite platform. Rate shall be
inclusive of making cut out sand polishing the edges for S.S. Sink
as per size required.Inclusive of 32mm dia down take pipe as
required up to nahani trap. ( Basic rate of granite - 1000 - 1350
Rs/Sq. m) (Mode of measurement - length x width )
RFT 17
17 PVC doors - Providing and fixing PVC Door of required size
and colour along with all accessories like Hinges, Tower Bolts,
Aldrop, Screw, Handel, tadi etc. hollow section of size
150mmX31mmX1.2mm UPVC profile with bordar of "U" hollow
size section of size 35mmX35mmX2mm the corner will be joined
with tough plastic of "L" angles at all corners with chromium
plated fixtures and fasteners stainless screws etc. complete. The
PVC door to have wood grain type finish to match the guest room
door laminate. Spec: (As directed by engineer in charge)
NOS. 5
18 FLUSH DOOR- Providing and fixing solid core flush door
shutter commercial in single leaf 32mm thick without ventilator
commercial type of exterior grade as per detailed drawings. Rate
shall be inclusive of all necessary approved fittings like hinges,
locks, 300mm long SS brushed finish handles,tower bolts, locks
and any necessary hardware items.SS handles to be provided on
both sides and finishing with decorative laminate 1mm thick on
both sides as approved by client or Architect. (Mode of
measurment - length x Height)
NOS. 11
19 Gypsum board false ceiling SQFT 900
Vastukala Design Build Solutions Pvt. Ltd. 15Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
Providing and fixing in position Gypsum Board False Ceiling
including Two coats of Plastic emulsion Paint of appd.quality as
per manufacturer's specifications and instructions with 12.5 mm
thick `Gypboard' Screw-fixed to the underside Of suspended G.I.
grid. G.I. grid should be Constructed and suspended from the
main ceiling as per manufacturer's instructions and as per
specifications using Original Co. Specified Framework Sections
G.I.24 gauge The Gypboard should be fixed to G.I. grid with 25
mm long Drawali Screws. The `Gypboard ' to be used should be
12.5mm thick tapered edge boards. The boards should Be taped
and filled from underside to give smooth, seamless ceiling. The
rate should include necessary additional ceiling sections and
intermediate channels openings for light fixtures, A.C. ducts,
vertical drops, offsets. etc.
Additional Intermediate channels should be fixed to strap
hangers for additional support to prevent strap hangers from
buckling/swaying at every 1200 mm. Item to be completed in all
respect including necessary sleeves for ducts finishing of joints
cut outs supports for A.C. grills, light fixtures, speakers
etc.Make: Gypusm board-India Gypsum. Panint-Asian/ ICI
The rate should include necessary additional ceiling sections and
intermediate channels openings for light fixtures, A.C. ducts,
vertical drops, offsets.and with two coats of putty, two coats of
approved primer, and three coats of approved lustre paint
19a Specification same as above for Vertical band of Gypsum 4" -6"
BAND
RFT 345
20 AC ply Boxing: Providing and fixing 18 mm thk Marine plywood
boxing conforming to IS710 on wooden / GI frame for covering
AC pipes. The boxing to be finished with gypsum board and 2
coats of plastic emulsion paint
SQFT 150
21 Providing & fixing 2' wide Granite Base Wash Basin Counter for
passage. and at 750mm height (top) above FFL of approved 20
mm thick granite fixed on 40mm thick horizontal kadappa with
1:4 cement mortar and vertical kadappa supports of 25 mm thick
as required. A 75- 100 mm high granite facia should be provided
with bull nosed edges, the top of facia to be 12mm above the
granite platform. the end to be granite with polished & full bull
nose moulding ( Basic rate of granite - 1000 - 1350 Rs/Sq. m)
(Mode of measurement - length x width ) The basic cost of
Granite 200/- per sft
RFT 25
1 15mm CPVC Pipes- Providing and fixing Chlorinated
Polyvinyl Chloride (CPVC) pipes confirming to IS 15778-2007
having 15/20/25 mm nominal outer dia Pipes for internal water
circulation. There are two types of water supply connection one
from 'PMC' and one from well water in 6 flats at all levels and
heights. item includes providing both the water supply
connections in all toilets and kitchen. for flushing in toilets only
provide well water connection with neccessary fittings. contractor
should visit the site and understand the scope and extent of piping
before filling the tender
LS
TOTAL CIVIL WORK COST (E)
B) PLUMBING WORKS
Vastukala Design Build Solutions Pvt. Ltd. 16Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
2 40mm dia UPVC pipe for basin drainage- Providing and fixing
leak proof and frost proof ASTMD (UPVC) Pipes of 40mm
dia having a wall thickness 5.08mm schedule 80 pipes (pressure
rating) for normal water supply and painting the pipe in white oil
paint etc. complete. Spec: (As directed by Engineer in charge))
RFT 50
3 110MM UPVC soil pipe: Providing, fitting and laying UPVC
soil pipe Confirming to IS 13592 - B type, including vent pipe
with all required C.I specials, plugs, clamps etc., of approved
Neco make(red color) confirming to IS 3989 , including,
excavation & back filling, jointing with drip seal all complete as
per specifications and direction of Engineer.
RFT 25
4 Concealed stopcock- Supply & Fixing of CP brass Concealed
stopcock with regular body of standard design and of approved
make confirming to ISI. (Jaquar continental series or
equivalent)Concealed stopcock- Supply & Fixing of CP brass
Concealed stopcock with regular body of standard design and
of approved make confirming to ISI. (Jaquar continental series
or equivalent)
NOS. 22
5 Angle stopcock- Supply & Fixing of CP brass Angle stopcock
of standard design and of approved make confirming to
ISI.(Jaquar continental series cat no. 055)Angle stopcock-
Supply & Fixing of CP brass Angle stopcock of standard
design and of approved make confirming to ISI.(Jaquar
continental series cat no. 055)
NOS. 7
6 Bib Tap- Providing & fixing in position CP brass two way
bib tap approved make full turn type, with heavy casted CP
brass wall flange. (Jaquar continental series or
equivalent)Bib Tap- Providing & fixing in position CP brass
two way bib tap approved make full turn type, with heavy
casted CP brass wall flange. (Jaquar continental series or
equivalent)
NOS. 16
7 Health faucet- Providing & fixing stealth faucet jet spray of
approved Jaguar or equivalent make including necessary
socket/union etc. complete as directed. (As directed by Engineer
in charge)Health faucet - Providing & fixing stealth faucet jet
spray of approved Jaguar or equivalent make including necessary
socket/union etc. complete as directed. (As directed by Engineer
in charge)
NOS. 5
8 Hand shower- Providing & fixing Handshower of approved
make including necessary fittings etc. complete. (Jaquar
continental series or equivalent)Hand shower- Providing &
fixing Handshower of approved make including necessary
fittings etc. complete. (Jaquar continental series or equivalent)
NOS. 5
9 Soap Dish holder- Providing & fixing in position Soap Dish
holder of standard make for complete finish item of work.
(Jaquar continental series or equivalent)Soap Dish holder-
Providing & fixing in position Soap Dish holder of standard
make for complete finish item of work. (Jaquar continental
series or equivalent)
NOS. 6
10 Toilet paper Holder- Supply & Fixing of Toilet paper holder
with paper of standard make for complete finish item of work.
(Jaquar continental series or equivalent)Toilet paper Holder-
Supply & Fixing of Toilet paper holder with paper of standard
make for complete finish item of work. (Jaquar continental
series or equivalent)
NOS. 5
Vastukala Design Build Solutions Pvt. Ltd. 17Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
11 Towel rail- Supply & Fixing single towel rail of 600 mm long
with standard make for complete finish item of work. (Jaquar
continental series or equivalent)Towel rail- Supply & Fixing
single towel rail of 600 mm long with standard make for
complete finish item of work. (Jaquar continental series or
equivalent)
NOS. 6
12 Mirror- Providing and fixing Box type mirror including
necessory fittings of size 450mm x400 mm single door. Note:
Prior approval of sample and brand by Incharge Engineer is
necessary before use.Mirror- Providing and fixing Box type
mirror including necessory fittings of size 450mm x400 mm
single door. Note: Prior approval of sample and brand by
Incharge Engineer is necessary before use.
NOS. 6
13 Wash Basin- Providing and fixing White Vitreous China
wash basin (Parryware - Kingsmere 0414) size 630 x 450 mm
with C.I. brackets, with bottle trap of approved make, 32 mm
C.P. brass waste of standard pattern, including painting of fittings
and brackets, cutting and making good the walls wherever
require. Wash Basin- Providing and fixing White Vitreous
China wash basin (Parryware - Kingsmere 0414) size 630 x
450 mm with C.I. brackets, with bottle trap of approved make, 32
mm C.P. brass waste of standard pattern, including painting of
fittings and brackets, cutting and making good the walls wherever
require.
NOS. 6
Vastukala Design Build Solutions Pvt. Ltd. 18Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
14 Overhead Shower- Providing and fixing Overhead shower
(ABS Chrome Plated) with Rubit cleaning system of approved
make including necessory fittings etc. complete. (Jaquar
continental series or equivalent)Overhead Shower- Providing
and fixing Overhead shower (ABS Chrome Plated) with
Rubit cleaning system of approved make including necessory
fittings etc. complete. (Jaquar continental series or equivalent)
NOS. 5
15 Napkin Ring Square- Providing and fixing SS Napkin ring
square of approved make including necessory fittings etc.
complete. (Jaquar continental series or equivalent)Napkin
Ring Square- Providing and fixing SS Napkin ring square of
approved make including necessory fittings etc. complete.
(Jaquar continental series or equivalent)
NOS. 6
16 European type commode- Providing and fixing European
type commode with cistern (Parryware - Flair-
C0237/281/C2067/C0757) conforming to IS:2556 -1994 (Part-
II) latest edition with PVC double seat cover commode or
equivalent including outlet, inter connections through walls
including all fittings etc. complete. Note: Prior approval of
sample and brand by Incharge Engineer is necessary before
use.
NOS. 5
17 Indian type water closet: Providing and fixing vitreous China
white glazed Indian type water closet of superior quality
580mmX480MM size Orissa pan(PARRYWARE make, model-
Orissa 580 with ISI-mark) with 'P' or 'S' trap, vent hole, with low
level PVC cistern of 10 liters capacity of "PARRYWARE make”,
syphon & standard flush fittings, CP connecting flush pipe,
15mm CP bras concealed stop cock deluxe type, 15mm dia
flexible PVC inlet water connection, all fittings Complete
including all materials etc complete
NOS. 1
18 Providing and Fixing Steel Sink (Nirali - Eureka delux
small - satin finish) of size 53.3 X 35.5 X 20 cm to
the Kitchen platform including UPVC waste coupling
pipe and coupling, necessory fittings & making good
the damaged surface etc. complete. Note: Prior
approval of sample and brand by Incharge
Engineer is necessary before use.
NOS. 1
19 Wall Mixer- Providing and fixing Wall Mixer with provision
for overhead Shower and Tel. Shower with 115mm long bend
pipe and wall Flange of approved make including necessory
fittings etc. complete. (Jaquar continental series or
equivalent)
NOS. 5
20 Piller Cock- Providing and fixing 15mm diameter Piller cock
P.V.C. polymer scratch resistant, anti-static with guarantee
against any manufacturing defect including socket, union nuts
etc. complete. Spec. (As directed by Engineer in Charge)
NOS. 6
21 Kitchen 2 way sink cock with Aquaguard arrangement-
Providing and fixing kitchen sink cock (wall mounted) with
swinging casted spout of approved make including necessory
fittings etc. complete. (Jaquar continental series or
equivalent)
NOS. 1
22 Nahani Trap- Providing and fixing 100 x 75mm HSI
floor/Nahani trap with CP hinged heavy brass grating to be
fixed with M15 and make water tight.
NOS. 10
- TOTAL PLUMBING WORK COST (F)
Vastukala Design Build Solutions Pvt. Ltd. 19Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
1 Trolley baskets- Providing and fixing Stainless steel baskets of
S.S. 304 grade of approved size with 2mm thk SS sheet & frames
with including necessory fitting etc. complete.
Type 1 - (520 x 535 x 100) NOS. 2
Type 2 - (520 x 535 x 150) NOS. 2
Type 3 - (520 x 535 x 350) NOS. 2
Type 4 - (520 x 535 x 300) NOS.
2 Shutter front- Providing and fixing 18 mm thk Marine
plywood conforming to IS710 shutter front with ply frame,
skirting. Shutter front shall be hinged to the frame work and
finished with 1 mm thk laminate of approved shade from outside,
0.8 mm white laminate from inside and 2 mm thk PVC edges
binding from all sides. Rate shall be inclusive of all necessary
approved fittings like hinges, magnet, handle, and any necessary
hardware items.
SQFT 45
3 Drawer front- Providing and fixing 18 mm thk Marine
plywood conforming to IS710 drawer front with ply frame,
skirting. Drawer front shall be fixed with heavy duty sliders to the
frame work and finished with 1 mm thk laminate of approved
shade from outside, 0.8 mm white laminate from inside and 2 mm
thk PVC edges binding from all sides. Rate shall be inclusive of
all necessary approved fittings like heavy duty sliders, ballcatch,
handle, slow closer and any necessary hardware items. (Designer
laminate base rate of 1350 Rs/ Sq.ft)
SQFT 25
4 Storage Unit- Providing and fixing storage units of full height as
per drawng. They shall consist of 18mm thk.marine. ply top,
sides,back, bottom, shelves and shutters. The bottom of the
storages shall be at 3” from FFL. The top of storages shall touch
the false ceiling level or 7'-0" ht. The shutter with box type higes
of approved make & steam beach lipping finished with melamine
with approved laminate on all the shutter edges. Division of the
shutters shall be made equally according to the length of the
storages (as approved by Bank/ architect). All the external
surfaces shall be finished with 1.0mm thick decorativeLaminate
(suede finish) of approved make.
SQFT 225
18mm thk. Ply shelves removable type supported on side steam
beach wood battens on both sides at 16” interval ( approximately
/ divided equally) shall be provided. All inner surfaces shall be
finished with 0.8 mm white laminate including the shutters . Rate
shall be inclusive of all necessary approved fittings like hinges,
locks, 150mm long SS brushed finish handles,tower bolts, locks
and any necessary hardware items. The top ply edge should be
fitted with 19mm x 7mm size steam beach moulding finished
with melamine. Wherever the plywood comes in contact with
the wall Black Japan shall be applied on backside of the
plywood.
5 Providing & fixing shutters below Wash basin counter with
19mm thick marine ply wood & approved 1mm lamination &
hardware fittings.
SQFT 50
C) FURNITURE WORK
Vastukala Design Build Solutions Pvt. Ltd. 20Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
6 Providing and fixing TV unit consisting of 3 drawers of 12-16"
deep on telescopic channels finished with corian finish. The item
includes panelling of 12mm thick around the TV for concealing
wiring and 12" wide ledge made out of 12 mm thick glass with
polished edges fixed with SS studs. Mode of measurement - Front
area of the TV unit in sq.ft including the cut out for TV .
SQFT 110
7 Providing & Fixing Study table made out of 18mm
thick ply frame work & beading patti as required. The
height of the table shall be 2'-6". Depth of the table
shall be 2'-0". The table shall have 1'-6" wide drawer
unit with one drawer and one shutter below the
drawers at the right side of the table. The front apron
shall be made in 12mm thk ply covered with additional
4" X 12mm thk ply finish with 1.00mm thick approved
color/make laminate as shown in detail drawing or as
per Banks Standard Design. All exposed surfaces of
the table & side table shall be finish with 1.00mm thick
approved make/color laminate from out side & 1.5mm
thick approved make/color laminate for TOP finish
with FRENCH polish from inside of matching of
laminate shades including approved make / design
Brush Finish S. Steel Handles, Brass Ball Catches,
Brass Locks,
RFT 15
Foot Rest made out of 12mm thick ply tapered box
finish with Rubber Matting, Brass Powder Coated
Wire Manager, Twin Telescopic Drawer Channel,
Metal CPU Metal Stand with Casters, necessary T.W.
NO. round 2" moulding etc. complete as per detail
drg. & instructions of the Architect.8 Supplying & fixing dining table with 6 chairs. NOS. 1
9 Supplying 3 seater sofa set as per approved Design. NOS. 2
10 supplying 2 seater sofa as per approved Design NOS. 2
11 Supplying king size double bed NOS. 5
12 Supplying Single bed for care taker NOS. 1
13 providing and fixing steel rod in balcony for drying cloths RFT 100
14 Providing and fixing curtain with stichng of approved shade RMT 50
15 Providing and fixing curtain rod RFT 170
1 Removing tiles- Removing any type of tiled flooring/ dado
with plaster in toilet walls and kitchen including levelling the
surface, cleaning the site including sorting out serviceable tiles
and carting away debris to approved lcoation of authority having
jurisdiction. Spec: (As directed by engineer in charge)
LS
2 Removing existing platform with partion in kitchen-Removing
existing kitchen platform and plastering the surface including
carting away debris to approved lcoation of authority having
jurisdiction. Spec: (As directed by engineer in charge)
LS
3 Demolition of existing brick wall-Dismantling 6” thk, brick
wall carefully by using chisel to cut & making good wall edges
with 1:4 cement plaster including removal of debris from site.
LS
FURNITURE WORK COST (G )
D) REBATE ITEMS
Vastukala Design Build Solutions Pvt. Ltd. 21Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune
4 Buy Back existing windows with MS grill ( the
contractor to give rebate )
Contractor to visit the flats to check the quantity and
quality of existing furniture,etc to buy back. The
furniture,etc. shall be taken back on "As it is where it
is basis"After removing the window from the location
contractor has to finish the edges of the window
opening to fix the new window.Window – 6'-0” x 4'-0” LS
Window – 3'-0” x 4'-0” LS
TOTAL DISMANTLING COST (H)
TOTAL OF PART - B (E+F+G+H)
GRAND TOTAL OF PART A & B
Vastukala Design Build Solutions Pvt. Ltd. 22Renovation work of
SBI-Madhuban flats 3-4, 5-6 and 7-8 at pune