RENOVATION & MAINTENANCE SYSTEMS & SOLUTIONS ......Permanent Repairing Solution Easy Application...

✓ Permanent Repairing Solution

✓ Easy Application

✓ High Mechanical Strength Products

✓ Optimum Solution For Each Case

✓ Upgrade The Value Of Your Property

RENOVATION & MAINTENANCE SYSTEMS & SOLUTIONS68 COMPLETE SOLUTIONS WITH DETAILED REPAIRING INSTRUCTIONS FOR THE MOST COMMON PROBLEMS

32

ContentsPaints restoration Common problems for outdoor surfaces 14Common problems for indoor surfaces 17Common problems for metal surfaces 19Common problems for wooden surfaces 21

Ceramic tiles application Ceramic tiles application on existing tiles 22Application of ceramic tiles on plasterboard 23Ceramic tiles application on wooden surfaces (MDF etc) 23Ceramic tiles application on steek surfaces 24Damaged tile grouts restoration 25Common problems and solutions 25

Surfaces cleaning Surface cleaning from Graffiti 26Tile grouts cleaning 27Cleaning of tiles from heavy dirt 27Stone & marbles waterproofing 28

Product Presentation 29

Outside masonry repairingCorroded steel repairing 4Crack on plaster repairing 5Crack on masonry repairing (when in contact with concrete) 5Crumbled and detached plaster repairing 6Small hair-cracks on plaster repairing 7Τotally cracked plasters repairing 7Common problems and solutions 8

Inside areas repairingCracks restoration at door/window frames 9Crack restoration on plaster 10Covering electric applications 10Surfaces Puttying 11Levelling plastered walls 12Αλλαγή δαπέδου απο πάτωμα σε πλακίδιο 12

Reinforced concrete repairing Damaged plaster repairing 13

1.01.11.21.3

1.41.51.61.7

2.02.12.22.32.42.52.6

3.0 3.1

4.04.14.24.34.4

5.05.15.25.35.45.55.6

6.06.16.26.36.4

LEGAL ANNOTATIONThe technical information and instructions included in the present brochure with regard to the application and end use of THRAKON products are based on the know-how and experience the Company has acquired so far pertaining to the products and are provided with good faith as long as they are stored, used and applied in accordance with THRAKON recommendations. Due to the fact that we cannot directly check the conditions prevailing at the worksite or the product application process, the Company shall not provide any guarantee with regard to the suitability of its products for a specific purpose and shall bear no legal responsibility that could be based on the information printed on the present brochure, on written or oral or other kind of recommendations and instructions. Product users are recommended to carry out a quick test on the suitability of the products with regard to each application and intention of use. THRAKON maintains the right to modify the properties/specifications of its products without prior notice. The publication of the present technical brochure annuls all previous publications.The most recent publication shall be in effect.

Older constructions often require the need for maintenance in order to repair some problems that have appeared through time. With the necessary repairs on masonry (inside and outside), on reinforced concrete, on plasters, paints, etc, problems can be solved and construction may be renewed and upgraded.

Moreover, after a period of time restoration is a critical need. THRAKON offers complete solutions consisted of high quality and efficiency systems, in order to make the renovation process a safe and guaranteed solution, durable in time.

THRAKON products are certified accordingly with European Norms, covering the needs of the most demanding ap-plications.

The present brochure is a presentation of indicative problems that have to do with repairs most constructions usually confront.

THRAKON strongly recommends to contact us, via email ([email protected]) in order to discuss about your problem and give the best possible solution for its restoration.

OUTDOOR MASONRY REPAIRINGINDOOR MASONRY REPAIRINGSREINFORCED CONCRETE REPAIRINGPLASTERS REPAIRINGPAINTS REPAIRINGTILE APPLICATIONSURFACES CLEANING

1.0 Outside masonry repairing

1.1 Corroded steel repairing

Problems on plasters, could create big prob-lems, through time, with moisture playing a major role in this.

STEP 2: Apply anticorrosive primer WRM 510 on steel reinforcement, with a brush.

Problems could affect reinforcement, with mois-ture attacking steel and causing corrosion.

STEP 3: Spray the surface of application with water.

STEP 1: Remove with a spatula all loose parti-cles of plaster and concrete. Then, clean thor-oughly the surface with a brush, from dust and other particles.

STEP 4: Apply the fi ber-reinforced, high strength (R4) repairing product WRM 525, with a spatula. Application thickness should not exceed 4 cm.

For structuring corners, either use a cor-ner-shaped spatula, or two spatulas togeth-er (pic). WRM 525 offers excellent bonding strength making it easy to structure a corner.

WRM 525 is a premium quality repairing product, fi ber reinforced, offering high strength (R4), making it appropriate for repairing old or new, reinforced or not concrete. It is suitable for the restoration of damages on concrete. It can be applied either by pouring it with a trowel/spatula or by spraying it on the surface to be repaired. It is non-shrinking, with excellent bonding with concrete, while it develops rapidly its mechanical properties.

WRM 550Fast setting repairing plasterConsumption: 13-14 kg/m² for 1cm thickness.

Products

Crack on masonry repairing (when masonry in contact with bearing structure) 1.3

STEP 1: Start by widening the crack by 15 cm, vertically.

STEP 2: Clean surface from dust and loose particles with a brush.

STEP 3: Spray the area of application with wa-ter, to increase bonding.

STEP 4: Apply the fast setting (20’) repairing product WRM 520, which offers high strength (R3).

STEP 6: When the fi rst layer of WRM 550 is dried, apply another layer of WRM 550, on top of the fi berglass mesh, in order to level the area.

STEP 5: Apply the fi rst layer of the fast setting reparing plaster WRM 550. Before the plasters gets dried, reinforce it by pressing THRAKON’s repairing fi breglass mesh (223 g/m2).

STEP 7

Crack on plaster repairing 1.2

STEP 1: Identify the crack of concern. STEP 2: Open the crack with a spatula at a width of 3-4 mm.

STEP 3: Clean thoroughly the area with a brush from dust and loose particles.

STEP 4: Proceed with the application of ELAS-TO PU along the opening of the crack.

STEP 5: Smoothen the applied product. Smoothing must be made before the applied product dries out.

STEP 6: Apply STATUS POLYPRIMER for preparing the surface, before the application of STATUS ALL WEATHER, a paint that is fl exible and ideal for waterproofi ng of walls.

5

WRM 525High strength, fi ber reinforced,repairing mortar R4Consumption: 17-18 kg/m²/cm layer thickness.

Products

4

ELASTO PU Polyurethane Sealing masticConsumption:Joint 5mm x 5mm: 12.5m per cartridge 310ml / 24m per alum. cartridge 600mlJoint 10mm x 10mm: 3.1m per cartridge 310ml / 6m per alum. cartridge 600ml

WRM 510Anticorrosive primer for steel reinforcementConsumption: 20 kg/m² for two coats.

ADVANTAGES: Easy in Application - Very High Mechanical Strength

ADVANTAGES: High Flexibility - Permanent Protection against Moisture

ADVANTAGES: Easy in Application - Permanent Protection against Moisture

Small hair-cracks on plaster repairing 1.5

1.4 Crumbled and detached plaster repairing

Due to aging, parts of plaster become loose and fi nally detach.

STEP 3: Apply fast setting WRM 520 on the sur-face of application. Wait 20 minutes to get dried.

STEP 6: Apply deep penetration primer, GLX 292 FLEX PRIM.

STEP 1: Remove crumbled plaster with a spat-ula and clean thoroughly the surface from dust.

STEP 4: Apply WRM 483 CEM COAT which is a cementitious putty.

STEP 7: Paint the surface with STATUS ALL WEATHER in two layers.

STATUS ALL WEATHER is a pioneering product that dyes and isolates the exterior walls at the same time, ensuring absoluteprotection from the humidity and exceptional endurance.

STEP 2: Prime the surface with the deep pene-tration primer GLX 292 FLEX PRIM.

STEP 5: Once WRM 483 CEM COAT has dried, proceed to rubbing of surface.

STEP 1: Clean thoroughly the surface from dust and loose particles, with a brush.

STEP 2: Priming of surface with STATUS DUR, solvent based primer.

Widespread cracked plasters repairing 1.6

When the plaster surface of the masonry is widespreadly cracked, then the ideal solution for repairing it is the Flexible Fiber-reinforced Plastering System that THRAKON offers.

ATTENTION: In case that the application is at a seaside area or area with high moisture content, THRAKON suggests the application of our silicone system. In such case, proceed to the following steps:STEP 7: Prime the surface with the colored silicone based primer GLX 498 SIL PRIM (4).STEP 8: Application of organic silicone based top coating DEC 438, at the color tone of our selection from CLIMAPLUS fan deck.

STEP 1: Clean thoroughly with a brush, the sur-face from dust loose particles.STEP 2: Start repairing the cracked surface with the fast setting, repairing mortar WRM 520 (R3).STEP 3: Prime the surface with deep penetration primer, GLX 292 FLEX PRIM (1).STEP 4: Apply the fi rst layer of fi ber-reinforced, base coat, THC 410 (2).STEP 5: As long as THC 410 is still wet, fi rmly CLIMAPLUS fi berglass mesh (160 g/m2) (3).STEP 6: Then, apply a second layer of fi ber-rein-forced, base coat, THC 410, in order to completely cover the mesh (2).

STEP 7: Prime the surface of application with the colored acrylic primer GLX 494 PRIM (4).STEP 8: Apply the organic acrylic based top coat-ing DEC 428, at the color tone of our selection from CLIMAPLUS fan deck.

WRM 483 CEM COAT FINEExtra Fine cementitious puttyConsumption: Approximately 1.3 kg/m2/mm thickness.

WRM 483 CEM COATFine cementitious puttyConsumption: 1.3 kg/m2/mm thickness.

Products

STEP 7: When WRM 550 has dried, smoothen it with a sponge trowel.

STEP 8: Prime the surface with STATUS DUR, solvent based primer.

STEP 9: Apply STATUS ALL WEATHER in two layers.

STEP 3: As soon as primer gets dried, fix irregularities of surfaces by covering small cracks with STATUS 100% ACRYLIC PUTTY.

STEP 4: If there are bigger levelling needs, please apply STATUS ONE COVER.

STEP 5: Application of STATUS ALL WEATH-ER in two layers.

6

STATUS ALL WEATHER Elastomeric Waterproof Facade PaintConsumption: 8-10 m²/L

Products

7

STATUS 100% Acrylic PuttyConsumption: 400 g/m2

ADVANTAGES: Repairing and on the same time Permanent Protection against Moisture

ADVANTAGES: High Flexibility - Permanent Protection against Moisture

ADVANTAGES: High Flexibility - Plastering System against Cracks

ProfessionalSeries

There are cases of small hair cracks exist-ing on the surface of plaster. They should be covered with a product be flexible enough to withstand thermal expansions, protecting our masonry.

1.7 Common problems and solutions

Problem Possible Causes Solution

Cracks on plaster like a web shape.

a) Plaster was applied during low temperature conditions

b) Plaster had a lot of water (during mix)

Application of Flexible Fiber-reinforced Plastering System ( § 1.6).

A crack appears on plaster at the corner (usually diagonally).

No application of diagonal fi berglass mesh, for reinforc-ing plaster at the corners of openings (windows, doors)

1: Widening of crack at 3cm depth.2: Levelling of surface with STATUS ONE

COVER.3: Application one layer of THC 410C.4: Application of fi berglass mesh, before THC

410C gets dried (on the opposite direction of the opening).

5: Application of repairing plaster WRM 550.

Having built with AAC blocks, after plastering, horizontal and vertical cracks appear on the joints of the blocks.

a) Application of fi nal coat plaster directly on AAC blocks.

b) Application was not made with the proper tools

Application of Flexible Fiber-reinforced Plastering System ( § 1.6).

Polyurethane Mem-brane applied on top of terrace became yellow from white.

No top coating applied (ali-phatic polyurethane coating)

1: Clean dirt from surface with water under pressure.

2: Mop surface with STATUS LS-703 solvent.3: 3 - 4 hours later apply one coat of FLX 390

PU.4: When FLX 390 PU is dried (and not after 12

hours) we proceed with application of FLX 390 TOP COAT.

Polyurethane membrane applied on top of terrace has bubbles at some points of application.

Entrapped moisture content at substrate

1: Cut bubbles with a spatula or a knife.2: Mop surface with STATUS LS-703 solvent.3: 3 - 4 hours later apply one coat of FLX 390

PU.4: When FLX 390 PU is dried (and not after 12

hours) proceed with application of FLX 390 TOP COAT.


Spots appear locally on polished cement screed (waxed concrete).

a) Possible entrapped moistrure content on substrate

b) Varnish was applied too early, entrapping moisture in substrate

c) Bad choice of varnish (water varnish chosen in wet areas instead of polyurethane varnish).

d) Bad application of varnish.

1: Surface rubbing with an electric sander in order to remove varnish.

2: Leave surface as long as it is needed for moisture to be evaporated.

3: Apply GLX 292 FLEX PRIM.4: Apply DECOR PU VARNISH (mat or gloss) in two

coats. Second coating applied after fi rst one is dried.

In case of upcoming moisture to remove polished cement screed and proceed to waterproofi ng substrate with DSF 353 SUPER ELASTIC before application of DECOR.

Cracks restoration at door/window frames 2.1

STEP 3: Protect surrounding area by applying a paper tape around the area of application.

STEP 4: Apply the polyurethane sealing mastic ELASTO PU FLEX, which is ideal for vertical applications.

STEP 5: Level ELASTO PU FLEX with our fi nger, before it gets dried.

STEP 1: Widen the crack by 3-4 mm with a spatula.

STEP 2: Thoroughly clean the surface from dust.

STEP 6: Before ELASTO PU FLEX gets dried, remove the paper tape.

STEP 7: As soon as ELASTO PU FLEX gets dried, it can be painted. STATUS POLYPRIMER should be used before painting the sealing mastic.

Inside areas repairing 2.0

THC 410 C Coarse-grained, fl exible, fi ber reinforced, adhesive – plasterConsumption: 3.0 - 4.0 kg/m2.

FLX 390 PUBrushable Polyurethane based elastic membrane (1K)Consumption: 1.3-1.8 kg/m² applied in two or three layers.

Products

ELASTO PU FLEX Polyurethane Sealing mastic for vertical jointsConsumption: Joint 5mm X 5 mm: 12.5m per cartridge 310ml/24m per alum 600ml.

Joint 10mn x 10mm: 3.1m per cartridge 310ml/6m per alum 600ml.

GLX 292 FLEX PRIM Acrylic primer - High penetrationConsumption: 50-70 g/m²

Products

98

ADVANTAGES: Easy in Application - High Flexibility

2.2 Crack restoration on plaster

STEP 4: Apply WRM 483 CEM COAT FINE, an extra-fi ne cementitious putty.

STEP 5: Leveling of surface with a spatula, re-moving the material in excess.

STEP 6: Leave WRM 483 CEM COAT FINE to get dried and rub with a wet sponged trowel for making the surface smoother.

STEP 7: Apply GLX 292 FLEX PRIM, deep penetration primer.

STEP 8: Apply STATUS ECO, ecological emul-sion paint, in two coats.

STATUS ECO is a premium quality ecological emulsion paint. It is odourless, easily cleaned and sustains frequent washing and little scratches.

2.3 Covering electric applications

In restorations, there is often the need of moving an existing electical socket or creating new electric or hydraulic supply. In these cases you should apply the following method for restoring the wall.

STEP 1: Clean thoroughly the surface of ap-plication from dust and loose particles, irregu-larities, etc. Then, spray water on the surface.

STEP 2: Filling of gap should be done with fast setting repairing product WRM 518 (R2).

STEP 3: Before WRM 518 starts getting dry, en-grave it diagonally for increased bonding and easier application.

STEP 4

Surfaces Puttying 2.4

STEP 2: Preparation of mixture by placing the required amount of DEC 470 in a clean buck-et. Then add water gradually, while you stir the content of the bucket.

STEP 3: Apply DEC 470, with a spatula, in two coats.

STEP 1: Thorough cleaning of surface from dust by using a metal brush.

STEP 4: After 10 - 12 hours, rub the surface with a wet sponged trowel for making the surface smoother.

STEP 5: Apply GLX 292 FLEX PRIM, deep pen-etration primer.

STEP 6: Apply STATUS ECO, ecological emul-sion paint in two coats.

STATUS ONE COVER Lightweight Acrylic Putty

WRM 518Fast setting repairing mortar R2Consumption: About 15 kg/m²/cm layer thickness.

Products

WRM 483 CEM COAT FINEExtra Fine cementitious puttyConsumption: Approximately 1.3 kg/m2/mm thickness.

STATUS ECO Premium EcologicalMat EmulsionConsumption: 12-15 m²/L

Products

STEP 1: Widen the cracks and remove of dust and loose particles.

STEP 4: Level STATUS ONE COVER with a spatula.

STEP 2: Clean thoroughly the crack opening, with a brush, from dust and loose particles.

STEP 6: Apply STATUS ECO, ecological emul-sion paint, in two coats.

STEP 3: Apply the lightweight acrylic putty STATUS ONE COVER, with a spatula, over the crack opening.

STEP 5: Apply GLX 292 FLEX PRIM, deep pen-etration primer.

When a crack is on the surface of plaster and masonry is not affected, it can be restored with no particular problems.

1110

ADVANTAGES: Easy in Application - Durable solution

ADVANTAGES: Easy in Application - Durable solution

ProfessionalSeries

ProfessionalSeries

ADVANTAGES: Super fi ne fi nish - Easy to clean

STEP 2: Application of STATUS 100% Acrylic Putty. For bigger gaps STATUS ONE COVER should be used.

STEP 3: Press putty applied with a spatula and remove material in excess. Then rub surface with a sand paper.

STEP 4: Prime surface with GLX 292 FLEX PRIM, deep penetration primer.

STEP 5: Apply STATUS ECO, ecological emul-sion paint, which can be easily cleaned, in two coats.

STEP 1: Clean surface from loose particles with a spatula and then clean throughly surface with a brush.

2.5 Levelling plastered walls

STEP 2: Application of GLX 292 FLEX PRIM, deep penetration primer, on concrete surface.

STEP 5: Apply lightweight, thermal insulating fl oor screed NSD 620 before it gets dried.

STEP 3: Leveling is needed in order to deter-mine maximum thickness of application, while following the necessary guides.

STEP 6: When NSD 620 has dried, proceed with the application of self-leveling screed NSF 610 (up to 10 mm).

Frequently, in renovations, existing wooden fl oor could be removed and replaced with ce-ramic tiles. STEP 1: Remove wooden fl oor and clean thor-oughly from dust and other particles.

STEP 4: Application of lightweight flooring screed NSD 620, which can be applied at a maximum thickness of 30 cm (wet-on-wet, 10 cm per layer).

2.6 Replacing parquet fl oor with tiles

NSF 610 is ideal for preparation of substrates before tile application. For bigger thickness applications use of NSF 611 (1 - 4 cm) is sug-gested.

Spiky roll is used for removing bubbles which might be created during application of self-leveling screeds. Then, proceed with tile applicaiton. We recomment the one-component, super-elastic tile adhesive (S2), VKW 129, which is ideal for demanding applications, like areas with permanent moisture content and heavy expansions and contractions.

Damaged plaster repairing 3.1

Reinforced concrete repairing 3.0

STEP 4: After 10 minutes, and since WRM 510 has dried, spray water on surface to increase bonding.

STEP 5: Application of WRM 525 with a trowel, by pressing it, with a maximum thickness of 4 cm.

STEP 6: In some occasions we might have to proceed to removing plaster from the whole surface of roof.

STEP 1: Remove all loose particles of plaster, before replacing it. Proceed to corroded steel.

STEP 2: Remove all rust and dust from reinforce-ment of concrete with a steel brush.

STEP 3: Apply WRM 510 with a brush, for pro-tecting steel against corrosion.

STEP 7: Clean thoroughly surface from dust and loose particles.

STEP 8: Prime surface with GLX 298, using a roll or brush.

STEP 9: Apply spray plaster SHP 205.

NSD 620 Lightweight, thermal insulating fl oor screed 3 - 20 cmConsumption: 10-11 kg/m²/cm

NSF 610Self-levelling fl oor screed up to 10 mmConsumption: 18 kg/m² for 1 cm thickness.

Products

WRM 510Anticorrosive primer for steel reinforcementConsumption: 20 kg/m² for two coats.

WRM 525High strength, fi ber reinforced,repairing mortar R4Consumption: 17-18 kg/m²/cm layer thickness.

Products

1312

STEP 10

ADVANTAGES: Easy in Application

ADVANTAGES: High Mechanical Strength - High Flexibility

ProfessionalSeries

ProfessionalSeries

ADVANTAGES: Excellent Repairing Solution - Durable solution

STEP 10: Apply NHP 250 one coat white plaster with marble.

STEP 11: Rub the surface with a sponged trowel. STEP 12: In case fi ner surface is required, use the DEC 470 FINE putty.

DEC 470 is an extra fi ne putty, ideal for indoor or outdoor applications. Leaves an extra fi ne surface, without lines, bubbles or bursts after drying.

4.1 Common problems for outdoor surfaces


Paint has loose particles - bubbles - blows.

a) Bad quality paint appli-cation

b) Only one coat application of paint

c) Probably there is a problem with plaster

d) Probable potential moisture content on substrate

1: Remove all loose particles with a sandpa-per and then clean surface thoroughly.

2: Application of STATUS 100% ACRYLIC PUTTY where needed.

3: Priming of surface with STATUS DUR solvent based.

4: Application of STATUS ALL WEATHER, in two coats.

Paints has started turn-ing into white powder.

Moisture on substrate, coming from:a) Lack of waterproofi ng

(upcoming moisture)b) Lack of waterproofi ng

(moisture coming from the back side of the wall)

c) Some small hair-cracks on plaster caused humidity coming in from paint

1: Remove all loose particles with a sand-paper and then clean surface thoroughly with a brush. In case of moist substrate, leave to dry.

2: Application of STATUS 100% ACRYLIC PUTTY where needed.


4: Application of STATUS ALL WEATHER, in two coats.

4.0 Paints restoration


Paint peels off.

a) Bad quality paint applicationb) Only one coat of paint applicationc) Probable hair-cracks on plasterd) Application during forbidding condi-

tions (high temperature)e) Incomplete cleaning of substrate

1: Remove all loose parts with a sandpaper and then clean surface thoroughly.

2: Apply STATUS 100% ACRYLIC PUTTY where needed.

3: Prime the surface with STATUS DUR solvent based.

4: Apply STATUS ALL WEATHER, in two coats.

Cracks appearance (< 1.2 mm).

a) Bad quality paint applicationb) Only one coat application of paintc) Probable hair-cracks on plasterd) Application during forbidding condi-

tions (high temperature)e) Incomplete cleaning of substratef) Probably there is a problem on

substrateg) Probably there is no mesh applied

when concrete comes in contact with brickwork

1: Remove all loose particles with a sandpaper and then clean surface thoroughly. In case of a bigger crack (> 2 mm), due to lack of fi berglass mesh, repair crack following direc-tions at step 1.2.

2: Apply the STATUS 100% ACRYLIC PUTTY where needed.



Bubbles appear on paint.

Adhesion problem coming from:a) Possible rainfall shortly after

applicationb) Possible high moisture content on

substratec) Painting application during forbidding

conditions (high temperature)

1: Remove all loose particles with a sandpaper and then clean surface thoroughly.




Colour tone is differ-ent in some parts.

a) Application of bad quality paintb) Paint was extremely dillutedc) Bad primer usedd) Bad application of paintinge) Probable painting over silicone,

without primer


2: Application of STATUS ALL WEATH-ER, in two coats.

STATUS DUR Waterproof primer, solvent basedConsumption: 12-14 m²/L

STATUS ALL WEATHERElastomeric Waterproof Facade PaintConsumption: 8-10 m²/L

Products

STATUS 100% Acrylic PuttyConsumption: 400 g/m2

STATUS ONE COVER Lightweight Acrylic Putty

Products

1514


Putting can be seen behind paint.

a) Bad quality paint applicationb) Putty bad applicationc) Primer bad selectiond) Painting application without any

primer used before



Paint has not cov-ered homogenously the surface.

a) Bad quality paint applicationb) Paint was dilluted too much before

application


After painting, vertical lines appear on surface.

Application during forbidden weather conditions (high moisture content)

1: Clean surface with water under pres-sure and leave surface to dry.


Paint fades out at some parts of application.

a) Bad selection of paint (not resistant to moisture)

b) Application of intense tone, tinted with a paint that is not resistant to UV Radiation (fl exibility and resistance).



Paint has wrinkled in parts of application.

a) Application during forbidding condi-tions (high moisture content)

b) Surface was infl uenced from weath-er conditions before it got dried

c) Application was made in very thick coats

1: Remove all loose particles with a spatula.

2: Clean surface thoroughly with a brush.



There is no good hiding power at some parts of wall, after application of paint.

a) Bad quality paint applicationb) Paint was dilluted too much before

applicationc) Application was made with poor

quality toolsd) There are cases where 3-4 coats of

paint must be applied

1: Application of STATUS ALLWEATHER, in two coats.

Common problems for indoor surfaces 4.2


Mold, ache or humidi-ty appears at lower parts of construction.

Moisture on substrate, coming from:a) possible leakage inside the wallb) lack of waterproofi ng (moisture

coming from the back side of the wall)

c) some small hair-cracks on plaster caused humidity coming in from paint

d) Increased moisture content in the environment of room


2: Repair substrate (repairing of moisture or water leakage, depending on problem).

3: Prime the surface with STATUS POLYPRIMER.

4: Apply STATUS KITCHEN & BATH, in two coats.

Black spots appear on surface (mainly on roofs or walls oriented northern).

a) No thermal insulation (wall oriented northern)

b) Increased moisture content in the environment of room


2: Repair substrate if needed (repairing of moisture or water leakage, depending on problem).

3: Prime the surface with STATUS POLYPRIMER.

4: Apply STATUS KITCHEN & BATH, in two coats.

Paint peels off.

a) Bad quality paint applicationb) Application of only one coat of

paintc) Bad preparation of substrate

(primer choice or application method)

d) Application during forbidding conditions (high temperature)

e) Incomplete cleaning of substrate

1: Remove all loose particles with a sandpaper and then clean surface thoroughly.


3: Prime the surface with STATUS POLY-PRIMER.

4: Apply STATUS ECO, in two coats.

Puttied parts of wall appear blow outs after painting.

a) Bad quality paint applicationb) Application of only one coat of

paintc) Bad preparation of substrate

(primer choice or application method)

d) Bad quality putty applied on substrate before painting

1: Remove all loose parts with a sandpa-per and then clean surface thoroughly.


3: Prime the surface with STATUS POLY-PRIMER.


STATUS DUR Waterproof primer, solvent basedConsumption: 12-14 m²/L

STATUS ALL WEATHERElastomeric Waterproof Facade PaintConsumption: 8-10 m²/L

Products

STATUS POLYPRIMEREcological multipurpose primerConsumption: 10-12 m²/L

STATUS Kitchen & BathConsumption: 12-15 m²/L

Products

1716


Painted surface leaves marks on our hands when rubbed. Bad quality paint application 1: Prime the surface with STATUS POLYPRIMER.


Stains from putty appear on painted surface.

a) Selection of paint with low hidding powerb) Puttied surface has not been primed before

paintingc) Paint was extremely dilluted d) Bad putting application

1: Prime the surface with STATUS POLYPRIMER.2: Apply STATUS ECO, in two coats.

Painted surface leaves marks of paint on sponge or cloth when cleaned.

a) Bad quality paint applicationb) Very hard sponge usedc) Very strong cleaning agent usedd) Paint was extremely dilluted


Infl ation marks appear on painted surface.

a) Application during forbidding conditions (high temperature)

b) Possible leakage inside wallc) Bad quality of plaster created such blow outs

1: Remove all loose parts with a sandpaper and then clean surface thoroughly. In case of mois-ture content existing on substrate, leave to dry.


3: Prime surface with STATUS POLYPRIMER.4: Apply the STATUS ECO, in two coats.

Painted surface turns yellowish or spots appear.

a) Increased moisture content in the room (bath-room, kitchen etc)

b) Room used from smokers and is not properly aired

c) The surface is close to a heater, radiator or fi replace

1: Prime the surface with STATUS POLYPRIMER.2: Apply STATUS KITCHEN & BATH, in two

coats.


During painting bubbles apeear on surface, while they leave small wholes when they blow.

a) Application was made with bad tools (roll, brush etc)

b) The application with roll was made too fastc) Bad quality paint applicationd) Application of satin paint on porous surface

without primer




After application I can see marks from brush or roll.

a) Application was made with bad tools (roll, brush etc)

b) The application with made with a lot of cross overs (more than the rest of the surface) at the same point (brush or roll)

c) Bad quality paint application




Common problems for metal surfaces 4.3


Paint peels off application surface.

a) Bad quality paint applicationb) Lack of cleaning on substrate (dust, loose parts etc)c) Bad preparation of substrate (bad application or no primer at all)

1: Remove all loose parts with a sandpaper or steel brush and then clean surface thoroughly.

2: Apply one coat of STATUS RUST PRIMER or STA-TUS BUILDING PRIMER.

3: Apply STATUS DUKO, gloss, extra strong enamel paint, in one or two coats.

Paint comes off metal surface.

a) Application with bad quality paintb) Lack of cleaning on substrate (dust, loose parts etc)c) Bad preparation of substrate (bad application or no primer at all)d) Application made without having rubbed metal surfacee) Application made before primer got driedf) Application made in very thin coat

1: Remove all loose parts with a sandpaper or steel brush and then clean surface thoroughly.

2: Apply one coat of STATUS RUST PRIMER.3: Apply STATUS DUKO, gloss, extra strong enamel

paint, in one or two coats.

Paint stays on our hand when rubbed or cleaned with wet sponge.

a) Paint has been exposed to solar radiation b) Paint was extremely dilluted c) Lack of cleaning on substrate (dust, loose parts etc)d) Application during forbidding conditions (high temperature)

1: Remove problematic paint, with a sandpaper or steel brush in order to completely remove rust.

2: Apply STATUS DUKO, gloss, extra strong enamel paint, in one or two coats.


STATUS ECO Premium EcologicalMat EmulsionConsumption: 12-15 m²/L

Products

STATUS RUST PRIMERAnticorrosive PrimerConsumption: 10-12 m²/L

STATUS DUKO Gloss Enamel PaintConsumption: 13-15 m²/L

Products

1918


Bubbles appear during appli-cation.

a) Bad quality paint applicationb) Application was not made with proper tools (brush,

roll etc)c) Application made in extreme conditions (high temper-

ature)d) Proper solvent was not used

1: Rub surface with a sandpaper.2: Apply STATUS DUKO, gloss, extra strong enamel

paint, in one or two coats. WHITE SPIRIT is suggest-ed to be dilluted with STATUS DUKO.

Takes too much time for varnish to get dried.

a) Application at a very thick coat of paintb) Application made on surface with existing oil remains

Apply STATUS DUKO, gloss, extra strong enamel paint, in one or two coats.

After application I can see marks from brush on surface.

a) Bad quality paint applicationb) Application was not made with proper tools (brush, roll etc)c) Application made in extreme conditions (high temper-

ature)d) Second coat applied without the fi rst coat having

dried



Varnish applied fade out after a short period of time.

a) Normal wear down because of suffi cient time passed after application

b) Application was not made with proper tools (brush, roll etc)

c) Surface is constantly exposed on hard weather condi-tions (extreme temperatures, solar radiation etc).


paint, in one or two coats.

Varnish applied starts getting wrinkled.

a) Application at a very thick coat of paintb) Second coat applied without the fi rst coat having

driedc) Proper solvent was not usedd) Application made in extreme conditions (high tem-

perature)



After application, paint starts «running» in various spots.

a) Application at a very thick coat of paintb) Second coat applied without the fi rst coat having

driedc) Paint was extremely dillutedd) Application made in extreme conditions (high tem-

perature)



Paint applied on railings said was suitable for application on rust, but rust has started rising again, while in some spots paint peels off.

a) Very thin coat of paint applicationb) Bad quality of paint applicationc) Substrate bad preparation

1: Rub surface with a sandpaper.2: Apply STATUS RUSTBLOCK or STATUS RUST-

BLOCK HAMMER FINISH, which is an integrated paint which guarantees strong protection against rust on every metal surface, preventing its reappearence.

Common problems for wooden surfaces 4.4


Paint has loose particles - bub-bles - blows.

a) Bad preparation of substrateb) Application of bad quality of paintc) Bad application of paintd) Application made on surface that had already too

many coats previously applied

1: Rub surface with a sandpaper and remove all loose parts.

2: Clean thoroughly surface from dust.3. Apply STATUS POLYPRIMER, an ecological multi-pur-

pose primer.4: Apply the ecological water based enamel paint STATUS

AQUADROP, which has great hidding power, easy application, does not stain and is completely odorless.

Having applied enamel paint for wooden surfaces, we see that there are local differences in tone or gloss.

a) Bad preparation of substrateb) Paint was extremely dilluted


2: Clean thoroughly surface from dust.3. Apply the ecological water based enamel paint STATUS

AQUADROP, which has great hidding power, easy application, does not stain and is completely odorless. Alternatively, you can use STATUS ENAMEL PAINT FOR WOODEN SURFACES, which has excellent quali-ty, perfect workability and great hidding power.

Paint removed by hand or gets scratched very easily.

a) Bad preparation of substrateb) Application of bad quality enamel paint for wooden

surfacesc) Bad application of paintd) Application made in extreme conditions (low

temperatures, big moisture content)

1: Remove paint with water (if product used is water based) or with LS-735 (Nitro solvent).

2: Apply the ecological water based enamel paint STATUS AQUADROP, which has great hidding power, easy application, does not stain and is completely odorless.

** For wood varnishes, protective water based STATUS AQUAWOOD should be applied.

Having applied a white solvent based enamel paint, the wood-en surface turns yellowish.

a) Application of bad quality enamel paint for wooden surfaces

b) Painted surface is in a room of smokersc) Painted surface is in a room with low or no light

(basement)d) Normal corrosion through time


2: Clean thoroughly surface from dust.3. Apply STATUS POLYPRIMER, an ecological multi-pur-

pose primer4: Apply the ecological water based enamel paint STATUS

AQUADROP, which has great hidding power, easy application, does not stain and is completely odorless.

STATUS DUKO Gloss Enamel PaintConsumption: 13-15 m²/L

STATUS RUSTBLOCK Hammer fi nish Anticorrosive Enamel PaintConsumption: 6-8 m²/L

Products


STATUS AQUADROP Ecological water based enamel paintConsumption: 12-14 m²/L

Products

2120

5.0 Ceramic tiles application

5.1 Ceramic tiles application on existing tiles

In restoration, we often have the need of new tiling in order to rennovate areas. In such occa-sions the application of an elastic tile adhesive like VKW 129 is suggested.

STEP 3: Application of GLX 190 with brush or roller, on all application area. Wait until it gets dried.

STEP 5: Distances between ceramic tiles can be easily fi xed with the relevant special items (+, T, Y).

STEP 1: Clean thoroughly substrate from dust and loose particles.

STEP 4: Proceed with tile application, starting from one corner of the area.

STEP 6: Apply FMF 160 LUX tile grout at the desired tone.

STEP 2: Apply GLX 190 quartz sand primer, which will create a very strong bonding the tile adhesive.

VKW 129 is ideal for very demanding appli-cations, since it is highly fl exible (C2TE S2), offering strong bonding and high resistance to expansions and contractions.

Application of ceramic tiles on plasterboard 5.2

Ceramic tiles application on wooden surfaces (MDF etc) 5.3

STEP 2: Apply the elastic tile adhesive VKW 128 (S1), which is ideal for such substrates like gypsumboards.

STEP 3: Apply FMF 160 LUX tile grout at the desired tone.

STEP 1: Prime the surface with quartz sand GLX 190. Alternatively we could use VLX 186.

VKW 132 ACRYL is the ideal tile adhesive for such applications in inside areas (wood, MDF etc).

Application of GLX 190 is made with brush or roller, on all application area. Wait until it gets dried.

VKW 132 ACRYL is an acrylic tile adhesive that does not need any water for preparation.

A lot of times we have the need to apply ce-ramic tiles on plaster boards (gypsumboards, cementboards etc).

In rennovations we often need to make an ap-plication in a very small area/room.

STEP 1

VKW 129 Super Elastic Tile AdhesiveConsumption: 2-4 kg / m²

FMF 160 LUX Porcelain grout

Products

GLX 190Acrylic Primer with quartz sand grainsfor tile & mosaicssConsumption: 0.4 kg/m²

VKW 132 2-Component Elastic Tile AdhesiveConsumption: 2.5-4 kg/m²

Products

22 23

ADVANTAGES: High Bonding Strength - Highly Flexible Tile Adhesive

ADVANTAGES: High Flexibility - Thixotropic

ADVANTAGES: Easy in Application - No water needed

STEP 1: Apply VKW 132 with the appropriate trowel (thickness).

STEP 2: Applcation of ceramic tiles is fast and easy.


STEP 4: Apply FMF 150 tile grout at the desired tone.

Application of absorbing and non-absorbing ceramic tiles, can be made on walls and fl oors, offering a fast and durable solution.

5.4 Ceramic tiles application on steek surfaces

There are cases where for rennovation purposes we would like to apply ceramic tiles on a steel surface (stair, fridge etc).

In these cases apply VKW 132, as long as the application is not bigger than 5 m2.

STEP 3: Apply the elastic tile adhesive, VKW 132. It is a two component product, ideal for applications under contractions and expansions.

STEP 1: Thorough cleaning of surface from dust with a brush.


VKW 132 is a high quality tile adhesive able to withstand contractions and expansions. It also offers excellent bonding, making it ideal for applications on steel surfaces.

STEP 2: Apply the GLX 190, quartz sand primer, for increased bonding.

GLX 190Acrylic Primer with quartz sand grainsfor tile & mosaicssConsumption: 0.4 kg/m²

VKW 132 2-Component Elastic Tile AdhesiveConsumption: 2.5-4 kg/m²

Products

Damaged tile grouts restoration 5.5

STEP 1: With a metal spatula remove the loose particles of the problematic tile grout.

STEP 4: After tile grout has dried, clean the surface with a sponge.

STEP 2: Clean thoroghly the surface from dust. Light cleaning with water is suggested.

STEP 5: Clean the area further with a wet sponge.

STEP 3: The mix is prepared, having chosen one of THRAKON’s FMF 160 tile grouts and applied with a rubber spatula.

FMF 150Tile Grout

FMF 155 2-component epoxy grout

Products

STEP 3

Common problems and solutions 5.6


Epoxy grout applied but after a short period of time it has started breaking into peaces

a) Bad application of tile grout (probably content A was not completely mixed with content B)

b) Hot oil on tile grout resulted to breaking it into pieces

c) Cleaning of tile grouts with steam cleanerd) Cleaning of tile grouts with an acidous cleaning

agent

1. Removal of tile grout.2. Thorough cleaning of

substrate.3. Application of

FMF 155.

24 25

ADVANTAGES: High Bonding Strength - Highly Flexible Tile Adhesive

ADVANTAGES: Easy in Application - For every grout thickness

6.0 Surfaces cleaning

6.1 Surface cleaning from Graffi ti

In urban centers it is common to see walls, plas-tered fences and other objects being vandalized with graffi ti. GRAFFITI REMOVER is an environ-mentally friendly product designed specifi cally for cleaning graffi ti over almost any surface.

If needed, repeat steps 1, 2 in order to clean all graffi ti from surface. It can be applied to clean graffi ti from surfaces like concrete, plasters, nat-ural stone, marble, granite, ceramic tiles, glass, aluminium, etc. Also it can clean graffi ti on top of cars as long as they have the manufacturer’s paint.

STEP 1: Apply plenty GRAFFITI REMOVER, in gel form, on whole surface with a sponge.

STEP 2: Leave GRAFFITI REMOVER for 2-3 minutes on surface and then clean with a clean sponge, wetted with lukewarm water.

Cleaning of tiles from heavy dirt 6.3

Tile grouts cleaning 6.2

Usually in areas with heavy traffi c we can see stains that are diffi cult to be cleaned. This is also a common problem in a kitchen.

STEP 1: Pour the VLX 182 on stained surface. VLX 182 is an acid cleaner and polisher for ce-ramic tiles and tile grouts.

VLX 182 acts immediately, removing stains from ceramic tiles and tile grouts. It removes concrete crust, salts, remains of tile adhesive and cemen-titious mortars in general, while it also removes stains from varnish, oil, grease etc.

There are cases where grouts get dirty from everyday use. In such cases, they can easily been cleaned with a mild cleanser VLX 181.

STEP 3: Where necessary, rub the grout with a brush to clean.

STEP 1: Add the VLX 181 into a container of water. For each 5m² you need one bottle of VLX 181. Then mop the surface.

STEP 4: Mop the surface with water in order to complete the cleaning.

STEP 2: The results are starting to become vis-ible after a few minutes.

VLX 181 cleans perfectly without causing dam-age, while providing shine. It is ideal for tiles with screen printing and special decorations, which are cleaned with a soft cloth.

Products Products


Epoxy grout applied, has not dried yet, after a long period of time.

a) Bad application of tile grout (probably content A was not completely mixed with content B)

b) Probable existence of moisture content on sub-strate, before application of tile grout

c) Probable increased moisture content (humidity of environment or rain), soon after application

1. Removal of tile grout.2. Thorough cleaning of

substrate.3. Application of

FMF 155.

STEP 2

26 27

ADVANTAGES: Easy Cleaning - Unique Shine

ADVANTAGES: Cleans stains, varnishes, oils, grease - Acts drastically

ADVANTAGES: Easy Cleaning - Works on most surfaces

VLX 181 Non-acid General Purpose Cleanerfor joints and ceramic tilesConsumption: 5 m²/L surface

VLX 182Acid General Purpose Cleaner or joints and ceramic tilesConsumption: 5.5 m2/L surface

BORNIT®-GRAFFITI REMOVER environmentally friendly, water-based emulsion, for indoors and outdoors areasConsumption: 0.5 kg/m²

29

STEP 2: Clean surface with a brush sponge.

STEP 5: Mop the surface in order to clean sur-face.

STEP 3: Thorough cleaning of surface with a sponge.

VLX 182 cleans surfaces from almost every kind of dirt, making it a necessary tool in every cleaning operation.

STEP 4: Good cleaning of surface with a wet cloth.

VLX 182Acid General Purpose Cleaner or joints and ceramic tilesConsumption: 5.5 m2/L surface

NANOSHIELD W Nanomolecular product for protection of porous surfaces against moisture. Consumption: 100-200 ml/m2

Products

28

6.4 Stone & marbles waterproofi ng

For the protection of surfaces against mold, fungus and the creation of salts, THRAKON offers NANOSHIELD W. NA-NOSHIELD W is a nanomolecular prod-uct which seals porous surfaces. It does not create a film and doesn’t get yellow when in contact with UV Radiation.

STEP 1: Clean the surface thorougly from dust. Local stains can be easily removed with VLX 181.

STEP 2: Apply NANOSHIELD W by brush or a roller or the whole surface. Appli-cation can also be made by spraying. The application needs to be done in two layers. Second layer should be applied within 3 hours from previous layer.

NANOSHIELD W is a hydrophobic prod-uct which is ideal for the protection of innorganic substrates, it does not cre-ate a film, it is water repellent and ideal for the waterproofing of such areas.

ADVANTAGES: Easy in Application - Protects against salts

Product Presentatio

WRM 512 BUILD Mortar for plastering and buildingMortar for plastering and building. Ideal for simple applications. Suitable for indoor and outdoor use.Consumption: about 15-16 kg/m²/cm

WRM 515 FIX Repairing mortar R2Repairing cement based product, one-component, type PCC R2 based on ΕΝ 1504-3. Suitable for repairs of concrete surfaces, masonry, plaster, construction ridges of roofs, gutters construction etc.Consumption: About 15 kg/m²/cm layer thickness. Gutter construction: 1.8 - 2.6 kg/m

R2

PCCΕΝ 1504-3

WRM 500 Fast setting repairing mortarWRM 500 is a fast setting sealing mortar (3 minutes setting time). Cement based, non shrinkable and only requires water for its preparation.Consumption: 1 kg yields approximately 0.6 L of ready to use mortar.

3min.

WRM 510 Anticorrosive primer for steel reinforcementOne-component, spread anticorrosive product, consisting of special specifications cement, silicon, resins and improvers additives.Consumption: 20 kg/m² for two coats.

ΕPOSHIELD INJECT S Injectable, two-component epoxy resin suita-ble for cracks width 0.1-3.0 mm.Injectable, two-component epoxy resin without solvents. Used to apply resin injections in concrete cracks width 0.1-3.0 mm.Consumption: 1.1 kg/L headspace for crack sealing.

ΕPOSHIELD INJECT W Injectable two-component epoxy resin for cracks> 3.0mm - bonding agentInjectable, two-component epoxy resin without solvents. Used to apply resin injections in concrete cracks width 0.1-3.0 mm.Consumption: 1.1 kg/L headspace for crack sealing.

WRM 483 CEM COAT Fine cementitious puttyExtra fine cementitious putty reinforced with special resins. With excellent workability, leaving a smooth finish, with high abrasion resistance, very good adhesion to the substrate, ready for painting. Consumption: Approximately 1.3 kg/m2/mm thickness.

R2

PCCΕΝ 1504-3

WRM 483 CEM COAT FINE Extra Fine cementitious puttyFine cementitious putty reinforced with special resins. With excellent workability, leaving a smooth finish, with high abrasion resistance, very good adhesion to the substrate, ready for painting. Consumption: Approximately 1.3 kg/m2/mm thickness.

R2

PCCΕΝ 1504-3

Repairing ProductsA

60min.

R2

PCCΕΝ 1504-3

WRM 518 Fast setting repairing mortar R2WRM 518 is a one-component, resinous, cement based, fast setting repairing material, type PCC R2 based on ΕΝ 1504-3. Consumption: About 15 kg/m²/cm layer thickness.

20min.

R3

PCCΕΝ 1504-3 WRM 520

Fast setting repairing mortar R3WRM 520 is a top quality, one-component, cement based, fast setting (in 20 minutes),type CC R3, based on EN 1504-3, repairing product for concrete surfaces. Non-shrinking, shows excellent relevance with concrete. Consisting of special specifications cement, silicon resins and additives. Anticorrosion antioxidant activity. Consumption: 25 kg of dry mortar yield approximately 13 lt of ready to-use mortar.

30 31

ELASTO PU Polyurethane Sealing masticELASTO PU is a one component polyurethane for waterproofing and bonding mastic, without solvents. Excellent adhesion to all building materials, sealing joints that require high flexibility. For use in interior and exterior areas. Consumption:Joint 5mm x 5mm: 12.5m per cartridge 310ml / 24m per alum. cartridge 600mlJoint 10mm x 10mm: 3.1m per cartridge 310ml / 6m per alum. cartridge 600ml

GLX 292 FLEX PRIM Acrylic primer - High penetrationReady to use micronized acrylic water-based primer with high penetration ability. Consumption: 50-70 g/m² depending on surface porosity.

FLX 390 PU Brushable Polyurethane based elastic membrane (1K)Brushable, elastic membrane (elasticity> 800%) polyurethane based, one-component used for long term waterproofing. Lifetime: 10 years. Uses: waterproofing roof, balconies and terraces, pots and flower beds, beneath paving on balconies, bathrooms, kitchens, swimming pools, etc, protecting the heat-insulating polyurethane foam. Walkability P3. Consumption: 1.3-1.8 kg/m² applied in two or three layers.

FLX 390 TOP COAT Brushable Polyurethane Elastic membrane (1K)Brushable, elastic membrane (elasticity> 800%) polyurethane based - one component used for long term waterproofing. Lifetime: 10 years. Uses: waterproofing and roof terraces, balconies and terraces, pots and flower beds, beneath paving on balconies, bathrooms, kitchens, swimming pools, etc, protecting the heat-insulating polyurethane foam. Walkability P4.Consumption: 120-150 g/m² applied in two or three layers.

ELASTO PU FLEX Polyurethane Sealing mastic for vertical jointsElastic, thixotropic, waterproofing and bonding mastic material, polyurethane based, one component. Excellent adhesion, high elasticity and resistance to common chemical and detergents. For use in indoor and outdoor applications. Consumption:Joint 5mm x 5 mm: 12.5m per cartridge 310ml/24m per alum 600ml.Joint 10mn x 10mm: 3.1m per cartridge 310ml/6m per alum 600ml.

STATUS DUR Waterproof primer, solvent basedTransparent, solvent based, waterproof primer for walls. Impregnates, stabilizes and waterproofs surfaces, while allowing them to breathe. It is the best preparation before painting vinyl or acrylic emulsions, Relief, paints for concrete or insulation boards.Consumption: 12-14 m²/L

Waterproofing

NANOSHIELD W Nanomolecular product for protection of porous surfaces against moistureProduct of nanomolecular structure, which seals the absorbent surfaces from moisture and from the occurrence of salts, molds and fungi. Consumption: 100-200 ml/m2, depending on the absorbency of the substrate.

NanomolecularProduct

R4

PCCΕΝ 1504-3

WRM 525 High strength, fiber reinforced, repairing mortar R4Premium quality and high strength, fiber reinforced, one-component, repairing mortar for concrete, type CC R4, based on EN 1504-3. Consumption: about 17-18 kg/m²/cm layer thickness.

WRM 550 Fast setting repairing plasterWRM 550 is a white, fast setting, cement based, repairing plaster/ render. It consists of cement, lime, marble and improvers admixtures. Perfect for small repairs on walls.Consumption: 13-14 kg/m² for 1cm thickness.

CEM I 42,5 R & 52,5 N High strength Portland cementHigh strength Portland cement resistant to compression, bending, abrasion, harsh weather conditions and corrosion.Produced in two types: • CEM I -52,5 N - White• CEM I -42,5 R - Grey.

CEM EXPRESS Fast Setting CementConsumption: For the production of ready mix 1L for use required about 1.6 kg CEM EXPRESS.

3min.

Polypropylene fi bersSynthetic polypropylene fibers that are effective in small doses. For watertight concrete tanks, watertight grout, reinforced coatings, anti-friction floors etc. Manufactured only from virgin polypropylene without plasticizers. Due to its special surface treatment, it decomposes very easily to 300 million per kilo (at 6 mm).Package: 0.9kg / 6mm

Fiberglass mesh (70 g/m²)Grid width 100 cm:Fiberglass for strengthening universal sealant spreads (e.g. FLX 380, FLX 382, FLX 385) in particular tough cases of multiple cracking.Dimensions: rolls 1m x 50m

Fiberglass for wall reinforcement (223 g/m²)10x10mmDimensions: roll 0.23 x 50m

MeshETICS (160 g/m²)Anti-alkaline fibreglass mesh, produced under ETAG 004.Consumption: 1.1 m/m²Dimensions: roll 1 m x 50 m

Mesh CLIMAPLUS (160 g/m²)Anti-alkaline fibreglass mesh, produced under ETAG 004.Consumption: 1.1 m/m²Dimensions: roll 1 m x 50 m

Mesh ETICS (145 g/m²)Anti-alkaline fibreglass mesh, produced under ETAG 004.Consumption: 1.1 m/m²Dimensions: roll 1 m x 50 m

Anti-alkalinefi berglass meshfor coatings (110 g/m²)10x10mm BlueDimensions: roll 1 x 50 m

Reinforcement

GLX 298 Acrylic based primer for improving plaster adhesion strengthGLX 298 is an acrylic based primer ready to use. Replaces the traditional spray plaster. Consists of synthetic resins and quartz sand.Consumption: 300-350 g/m²

BORNIT®-GRAFFITI REMOVERGraffiti-remover is an environmentally friendly, water-based emulsion, deep-penetrating effect, used on granite, marble, limestone, concrete, glass, aluminum, bricks, plaster and glazed tiles, for indoors and outdoors areas.Consumption: 0.5 kg/m²

B

C

32 33

STATUS RUST PRIMER Anticorrosive PrimerPrimer with excellent anticorrosive properties and high durability. Provides effective protection against rust, even under harsh weather conditions. Its superior workability and excellent speading capacity ensure very good covering and exceptional final result. Consumption: 10-12 m²/L

STATUS AQUADROP Ecological water based enamel paintFinest quality certified ecological water based enamel paint, ideal for interior and exterior use. Some of the main advantages of this product is that it is odorless and does not turn into yellow after some time. It spreads easily and covers wonderfully, leaving a lovely surface to withstand frequent washing and harsh weather conditions for many years.Consumption: 12-14 m²/L

VLX 186 Acrylic Admixture for mortars – Primer for special applicationsVLX 186 is an environmental friendly, acrylic admixture for mortars and a primer for non-absorbing substrates. It does not contain organic solvents. It is used as a primer for bonding tiles on demanding substrates (old tiles, marble, mosaic). Consumption: Admixture: 40-80g VLX 186 per kgPrimer: 1 Kg / 14-15 m2 (non absorbing substrates)

1kg/5m2 (absorbing substrates)

Paints

STATUS ECO Premium Ecological Mat EmulsionPremium quality ecological emulsion paint, ideal for indoor surfaces. It is odorless and environment friendly. Spreads wonderfully, has excellent hiding power and high efficiency. Sustains frequent washing. It has the official eco-certification by the EU.Consumption: 12-15 m²/L

STATUS Kitchen & BathAntimould high quality emulsion paint with strong antifungal properties. It has excellent hiding power, high performance and easy implementation. It leaves a unique, rich mat finish that withstands washing and retains its color unchanged, giving the feeling of clean and freshly painted room for a long time.Consumption: 12-15 m²/L

STATUS ALL WEATHER Elastomeric Waterproof Facade PaintSTATUS All-weather is a pioneering product that dyes and isolates the exterior walls at the same time, ensuring absolute protection from the humidity and exceptional endurance. Its special composition creates a flexible membrane that covers all the veins and «monitors’’ the constrictions and dilations of the surface. Thanks to the built-in filters against the ultraviolet radiation it remains flexible without going off or peeling.Consumption: 8-10 m²/L

STATUS POLYPRIMER Ecological multipurpose primerEcological water soluble multipurpose undercoat for interior and exterior use. Certified with Ecolabel. Easy to apply, has excellent hiding power and ensures high adhesion and a flawless end result.Consumption: 10-12 m²/L

WACG2 FMF 160 LUX

Porcelain groutGrout with a characteristic chromatic homogeneity and stability and high mechanical strengths. It ensures sealing, achieving excellent water repellent properties and antifungal protection. Prevents the growth of microorganisms and the formation of fungus and salt stains on its surface. FMF 160 LUX is a fast setting grout and it is classified as type CG2 according to EN 13888. Consumption: 0.2 - 2 Kg/m2 (depending on the size of the plate and the joint). VKW 129

Super Elastic Tile AdhesiveSuperplastic tile adhesive suitable for most demanding applications. Consumption: 2-4 kg/m²

S2C2TE

ULTRA FLEX

Tile Adhesives & Grouts

S2C2TE

VKW 132 2-Component Elastic Tile AdhesiveHighly flexible, 2-component, tile adhesive, for surfaces subjected to thermal expansions and vibrations. For indoor and outdoor surfaces.Consumption: 2.5-4 kg/m²

RG

FMF 155 2-component epoxy groutHigh resistance for special structures and business areasFMF 155 is a two-component epoxy solvent-free tile grout, suitable for filling joints 2-12mm. After setting, it offers high mechanical strength (compressive, flexural, adhesion) and resistance to chemicals (acids, alkalis, many organic solvents). Equally resistant to weathering, water and saline water. Classified as type CG2 WA grout, according to European standard EN 13888. Available in packs of 3 kg (A: 2.82 kg - B: 0.18 kg).

WACG2

FMF 150 Tile GroutEnhanced technical features and excellent workabilityFMF 150 is a one component, polymer modified, cement based, tile grout produced with quartz sand. It is classified as type CG2 according to EN 13888. It is available in two types:• Fine grain No. 301 - No 326: application thickness up to 5mm.• Coarse grain No. 501 - No 525: application thickness 5-20 mm.

VLX 181 Non-acid General Purpose Cleanerfor joints and ceramic tilesVLX 181 is a non-acid transparent general purpose cleaner for marble and tiles with lemon perfume. It cleans in depth, without causing any disaffects, and at the same time shines perfectly. Consumption: 5.5 m²/L surface

VLX 182 Acid General Purpose Cleaner or joints and ceramic tilesVLX 182 is an acid transparent liquid cleaner and shining aid for joints and ceramic tiles. Cleans, shines and maintains the colors of grout vibrant and shiny after application. Consumption: 5.5 m²/L surface

GLX 190 Acrylic Primer with quartz sand grainsfor tile & mosaicssAdhesion primer that consists of synthetic resin, inorganic fillers and quartz sand with selected grain size. Increases the bonding strength of the tile adhesive on smooth and low absorbing surfaces.Consumption: 0.4 kg/m²

STATUS DUKO Gloss Enamel PaintGlossy extra strong enamel paint, suitable for decoration and protection of all metallic surfaces, indoor and outdoor. Featuring excellent hiding power and easy brushing, it offers a perfect finish, with exceptional resistance in hard weather conditions, providing a longlasting protection and shades that survive unaltered for a long time.Consumption: 13-15 m²/L

VKW 128 Highly Elastic Tile AdhesiveFrost flexible, cement-based, tile adhesive, produced with quartz sand, intented for applications on both horizontal and vertical surfaces. It offers slip resistance, extended open time, very high elasticity and excellent workability. For indoor and outdoor surfaces. Consumption: 2-4 kg/m²

S1

C2TESUPER FLEX

STATUS AQUAWOODProtective Water Based Wood VarnishWater based woodstain varnish, specially formu-lated for the effective protection of the indoor and outdoor wood, enhancing the natural beauty of wood. It is odorless, fast drying, does not crack or peel and offers deep penetration to the wood, while allowing it to «breath».Available in clear and in 8 shades: Pine, Oak, Cherry, Chestnut, Walnut, Mahogany, Oregon and Teak.Consumption: 18-20 m²/L

Crosses for Tiles

Shape T for tiles

Shape Y for tiles

D

Ε

34

Flooring Screeds

NSD 620 Lightweight, thermal insulatingfloor screed 3 - 20 cmNSD 620 is a light, ready to mix mortar suitable for floor filling and leveling thermal insulating properties. Consists of cement, grains form crushed AAC, quartz sand of 3.5 mm max grain and admixtures.Consumption: 10-11 kg/m² of dry mortar for 1 cm thickness.

NSF 610 Self-levelling floor screed up to 10 mmNSF 610 is a self-levelling, cement based mortar for smoothening and levelling of floors. Consists of cement, quartz sand of 0.5 mm max grain and admixtures.Consumption: 18 kg/m² for 1 cm thickness.

THC 410 C Coarse-grained, flexible, fiber reinforced, adhesive – plasterCoarse grained, fiber reinforced, polymer modified, cement based mortar. It consists of cement, quartz sand with 1.5 mm max. grain size, limestone fillers and admixtures. It complies with EN 13499 and ETAG 004. Suitable for bonding and plastering.Consumption: 3.0 - 4.0 kg/m²

GLX 498 SIL PRIM Silicone primer - TransparentSilicone based primer with high penetration. Colored according to the shade chosen for final coating (organic plaster).Consumption after dilution: 0.20 kg/m² per layer.

GLX 494 PRIM Acrylic primer - TransparentAcrylic based primer with high penetration. Colored according to the shade chosen for final coating (organic plaster).Consumption after dilution: 0.20 - 0.25 kg/m² per layer.

DEC 428 POLYPLASTDecorative Acrylic PlasterAcrylic based render with high elasticity and excellent adhesion, offering colored end surfaces in different types (RILLEN or SCRATCH), without the need to paint.

DEC 438 SILICONEColored Silicone PlasterSilicone render with high vapor permeability and additional antifungal activity. Offers colored end surfaces in different types (RILLEN or SCRATCH).

THC 410Highly flexible, fiber reinforced,adhesive – plasterPremium, highly flexible fiber-reinforced, polymer modified, cement based mortar with increased strength. It consists of cement, quartz sand with 0.5 mm max grain size, limestone fillers, polypropylene fibers and admixtures. It complies with EN 13499 and ETAG 004.Consumption: 3.5 - 4.0 kg/m²

SHP 205Spray plasterSpray plaster for surface preparation, acting as a bridge to enhance adhesion for the next layers of plaster.Consumption: 5 kg/m² for thickness of application 0.5 cm.

NHP 255One hand plaster with marbleOne hand, white plaster that replaces the base coat plaster and the final coat plaster. Provides leveling and smoothing with one hand use. The extra white marble composition contributes to the snow white result.

WHITE SPIRIT Solvent for paint brush

REMOVER New generation powerful corrosive for paints and varnishes. Does not contain dichloromethane.

STATUS ONE COVER Lightweight Acrylic PuttyWhite, ready to use, lightweight acrylic putty for indoor and outdoor surfaces. It is easily applied and does not crack. The surface can be painted as soon as the putty is dry.

STATUS Building PrimerIdeal undercoat for the preparation of metal surfaces. Workes softly spreads wonderfully, has great coverage and does not flow. Provides very good adhesion to the final color. Ensures very good accretion in the final color, offering a uniform surface and exceptional final result. Consumption: 10-12 m²/L

STATUS Enamel paint for wooden surfacesExcellent quality, solvent-based paint for interior and exterior use. Featuring excellent hiding power and easy brushing, it offers a perfect finish, washable, with great resistance in hard weather conditions, providing a long-lasting protection.Consumption: 14-16 m²/L

STATUS 100%Acrylic PuttyWhite putty for indoor and outdoor use in construction.Can be used as filling material on surfaces made of plaster, wood, concrete e.t.c. It has easy application and when sanded it offers a smooth and durable surface without cracks. Consumption: 400 g/m2

STATUS RUSTOBLOCK Hammer finish Anticorrosive Enamel PaintSpecially designed paint to be applied on rusty surfaces without prior use of rust primer, offering a hammer effect as a final result. Exhibits high adhesion and very good leveling and offers excellent resistance to harsh weather conditions. The result is a shiny, highly durable surface, with intact nuances for very long time. Available in 5 colors.Consumption: 6-8 m²/L

Plasters & Renders

DEC 470Fine-grained Spatula putty– for indoor & outdoor useWhite, one component, dry mix putty. Replaces the traditional stuccos and oil stuccos. The final result gives a very smooth surface, without lumping, lines and cracks after drying.Consumption: 1.0 kg/m² for two layers.

STATUS RUSTOBLOCK Anticorrosive Gloss Enamel PaintSpecially designed paint to be applied on rusty surfaces without prior use of rust primer, offering a glossy effect as a final result. Exhibits high adhesion and very good leveling and offers excellent resistance to harsh weather conditions. The result is a shiny, highly durable surface, with intact nuances for very long time.Consumption: 6-8 m²/L

STATUS LS-703 Solvent for air paints, oven xylene base.Suitable for dilution: CARMYPOOLPRIMER, CARMYPOOL & CARMYSAIL

CLIMAPLUS - ETICS & Facade Products

DECOR PU VARNISH Polyurethane varnish- two components, for protecting polished cement screedsTransparent polyurethane varnish, two components. It offers excellent waterproofing, high mechanical strength, resistance to chemical agents, protection against yellowing and UV radiation. Consumption: 80-120 ml/m², depending on the porosity of the substrate.*Available in gloss and mat.

F

G

H

www.thrakon.gr/en 54th km. National Road Athens-Lamia, Inofyta Viotias, PC 32011T. +30 22620 32970, F. +30 22620 56020

in8

crea

tive

des

ign

SUPORT TEHNIC

800 100 1414

RENOVATION & MAINTENANCE SYSTEMS & SOLUTIONS ......Permanent Repairing Solution Easy Application...

Documents

Transcript of RENOVATION & MAINTENANCE SYSTEMS & SOLUTIONS ......Permanent Repairing Solution Easy Application...