Renishaw NC2 - NC3 - Installation and User's guide
description
Transcript of Renishaw NC2 - NC3 - Installation and User's guide
Installation and user’s guideH-2000-5196-04-A
NC2 non-contact broken tool detection system andNC3 non-contact tool setting system
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-i
Warranty
Equipment requiring attention under warranty must bereturned to your supplier. No claims will be consideredwhere equipment has been incorrectly installed ormisused, or where repairs or adjustments have beenattempted by unauthorised persons. Prior consent mustbe obtained in instances where Renishaw equipment is tobe substituted or omitted. Failure to comply with thisrequirement will invalidate the warranty.
Patents
Features of the NC3 non-contact tool setting system andthe NC2 non-contact broken tool detection system aresubject to the following patents and patent applications:
© 2002-2004 Renishaw plc. All rights reserved.
Renishaw® is a registered trademark of Renishaw plc.
This document may not be copied or reproduced inwhole or in part, or transferred to any other media orlanguage, by any means, without the prior writtenpermission of Renishaw.
The publication of material within this document does notimply freedom from the patent rights of Renishaw plc.
Disclaimer
Considerable effort has been made to ensure that thecontents of this document are free from inaccuracies andomissions. However, Renishaw makes no warranties withrespect to the contents of this document and specificallydisclaims any implied warranties. Renishaw reserves theright to make changes to this document and to the productdescribed herein without obligation to notify any person ofsuch changes.
Renishaw part no: H-2000-5196-04-A
First issued: 09 2002Revised: 02 2003
08 200303 2004
CN 1339040AEP 1050368EP 1208351JP P2000-346614TW NI-153868TW NI-178572
US 2003-0060919US 6,635,894 B1US 6,496,273 B1WO 01/38822WO 01/55670WO 03/092955
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-ii Preliminary information
EC DECLARATION OF CONFORMITY
Renishaw plc declares that the products:
Name DescriptionNC2 Non-contact broken tool detection systemNC3 Non-contact tool setting system
have been manufactured in conformity with the following standards:
BS EN 61326: 1998/ Electrical equipment for measurement,A1:1998/A2:2001 control and laboratory use - EMC
requirements. Immunity to annex A -industrial locations. Emissions to class A(non-domestic) limits.
EN 60825-1:1993 Safety of laser products.A1:1997/A2:2001 Part 1: Equipment classification,
requirements and user’s guide.
and that they comply with the requirements of the followingdirectives (as amended):
89/336/EEC Electromagnetic compatibility73/23/EEC Low voltage
The above information is summarised from the full ECDeclaration of Conformity. A copy is available from Renishaw onrequest.
FCC
Information to user (FCC Section 15.19)
This device complies with Part 15 of the FCC rules. Operation issubject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,including interference that may cause undesired operation.
Information to user (FCC Section 15.105)
This equipment has been tested and found to comply with thelimits for a Class A digital device, pursuant to part 15 of the FCCRules. These limits are designed to provide reasonableprotection against harmful interference when the equipment isoperated in a commercial environment. This equipmentgenerates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with this installation guide,may cause harmful interference to radio communications.Operation of this equipment in a residential area is likely tocause harmful interference, in which case you will be required tocorrect the interference at your own expense.
Information to user (FCC Section 15.21)
The user is cautioned that any changes or modifications notexpressly approved by Renishaw plc or authorised representativecould void the user’s authority to operate the equipment.
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-iiiWarnings and cautions
Warnings
Use of controls or adjustments or performance ofprocedures other than those specified within thispublication may result in hazardous radiationexposure.
Switch off the power supply before carrying outmaintenance on the NC2 or NC3 unit.
Caution – Laser safety
The laser used in the Renishaw NC2 non-contactbroken tool detection system and NC3 non-contact tool setting system emits continuousvisible red light at a wavelength of 670 nm andhas a power output of less than 1 mW.
The laser used is classified as a Class 2 productas defined by International standard IEC60825-1:1993 + A1:1997 + A2: 2001.
The laser complies with 21CFR 1040.10 and1040.11 except for deviations pursuant to LaserNotice No. 50 dated July 26, 2001.
! The standard IEC 60825-1 directs to attach alaser warning label and explanatory label.
A warning label and explanatory label arepermanently fixed to each side of the transmitter(Tx) housing (see the next page for details). Anadhesive explanatory label is provided forattachment outside the machine.
Safety rules
● Do not stare directly into the laser beam. Thebeam may be viewed safely from the side.
● Avoid visual exposure to the beam withoptical appliances. Ensure that the beam isnot reflected into the eyes of another personvia a mirror or other reflective surface.
● Do not expose skin to the laser beam forlonger than is absolutely essential. Instructall operators about the hazards of direct eyecontact, or long skin exposure, with the laser.
● Attach the laser warning label supplied in aneasily visible location on the machine.
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-iv Laser warning labels and location of laser aperture
Label BLabel A
Warning label
Explanatory label
Label B
Label A
Laser aperture
** Except for deviations pursuant toLaser Notice No. 50 dated July 26 2001
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-1
NC2 and NC3 unitsDimensions and mounting dimensions .................................................................................... 1-3
Maintenance ............................................................................................................................. 1-4Introduction ......................................................................................................................... 1-4Guidelines .......................................................................................................................... 1-4Cleaning ............................................................................................................................. 1-4Air regulator unit ................................................................................................................. 1-7
Installation ............................................................................................................................... 1-10Base and side mounting options ...................................................................................... 1-10Angled mounting option ................................................................................................... 1-11Mounting the unit .............................................................................................................. 1-12Air supply .......................................................................................................................... 1-13Conduit adaptor and conduit ............................................................................................ 1-16Securing the conduit ........................................................................................................ 1-17
NC2 unit onlyIntroduction ............................................................................................................................. 1-18
Software routines .................................................................................................................... 1-18
Power supply .......................................................................................................................... 1-18
Cleaning .................................................................................................................................. 1-18
Specification ........................................................................................................................... 1-19
Alignment ................................................................................................................................ 1-20Achievable set-up tolerances ........................................................................................... 1-20Aligning the NC2 .............................................................................................................. 1-20
Electrical connections – NC2 to machine controller .............................................................. 1-22
Parts list .................................................................................................................................. 1-23
ContentsC-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-2
NC3 unit onlyIntroduction ............................................................................................................................. 1-25
Recommended feedrates ....................................................................................................... 1-25
Software routines .................................................................................................................... 1-25
Specification ........................................................................................................................... 1-26
Alignment ................................................................................................................................ 1-27Achievable set-up tolerances ........................................................................................... 1-27Aligning the NC3 .............................................................................................................. 1-27
NCi-4 interface installation ..................................................................................................... 1-29
Parts list .................................................................................................................................. 1-32
ContentsC-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-3Dimensions and mounting dimensions
26(1.02)
135 (5.32)
80 (3.15)29 (1.14)
34(1.34)
25(0.98)
38 (1.50)
13(0.51)
67.5(2.66)
77(3.03)
59.5(2.34)
Status LED forindication only
Ø17(0.67)
9 (0.35)
32.5(1.28)
35.5(1.40)
4.25(0.17)
47 (1.85)
31 (1.22) centre of beam
18 (0.71)
13(0.51)21.75
(0.86)
Dimensions in mm (in)
62 (2.44)
26(1.02)
±2°
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-4 Maintenance
Introduction
The NC2 and NC3 units require minimalmaintenance, having been designed to operate aspermanent fixtures on a CNC machining centre inan environment of hot metal chips and coolant.
Only the maintenance routines described in thisguide should be undertaken. Further dismantlingand repair of Renishaw equipment is a highlyspecialised operation and must only be carriedout at authorised Renishaw Service centres.
Equipment requiring repair, overhaul or attentionunder warranty should be returned to yoursupplier.
Guidelines
● The NC2 and NC3 are precision tools andmust be handled with care.
● Ensure that the unit is firmly secured to itsmounting.
● Do not allow excessive waste material tobuild up around the unit.
● Keep electrical contacts clean.
● The NC2 and NC3 units are protected by acontinuous stream of clean air.Approximately once a month, inspect theoptics for contaminants. The service intervalmay be extended or reduced dependentupon experience.
● Optimum performance is achieved byrunning the system continuously.
Cleaning
Cleaning may be required if the air to the NC2 orNC3 becomes contaminated or if the system isleft with the air off when coolant is present.
Excessive contamination will block the laserbeam and prevent the system from functioning. Ifcontamination is suspected, identify the causeand rectify the problem before cleaning thesystem. If necessary, change the air pipe.
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-5Maintenance
Clean the NC unit as follows:
1. Switch off the air supply and power supply.
2. Remove the air channel plug.
3. Remove the air caps from the transmitter andreceiver units using the pin spanner provided.
4. Switch on the air supply and increase thepressure to purge out coolant that may bepresent.
5. When no further coolant is emitted fromthe housing for 1 minute, switch off theair supply.
(continued on next page)
Air capPin
spanner
Air channelplug
Air cap
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-6
6. Wipe the optics of the NC unit with either apolyester swab or a cotton bud soaked inalcohol or similar (see the figure).
7. Replace the air channel plug and tighten to1.3 Nm (0.95 lbf.ft).
8. Clean and replace the two air caps andtighten each one to 2 Nm (1.48 lbf.ft).
9. Switch on the air supply and set the pressureto 2 bar (29 psi).
10. Switch on the power supply.
Maintenance
Cleaning solvent RS Components Ltdpart number 266-0856 (recommended).Alternatively, a mixture of 75% isopropylalcohol with 25% water may be used.
Polyester swabRS Components Ltd part number
408-1794 (recommended)
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-7Maintenance – air regulator unit
Checking the liquid level
Regularly check the level of the accumulatedliquid in each of the filter bowls. It is importantthat the level is kept below the filter element.
Draining the liquid
Drain the liquid that has accumulated in a filterbowl as follows:
1. Switch off the air supply. A quantity of liquidwill drain from the bowl.
2. Switch on the air supply. Check that thepressure is set to 2 bar (29 psi). Adjust ifnecessary.
3. If the level of the liquid in the bowl is still toohigh, repeat steps 1 and 2 until the levelreduces to a satisfactory level.
Air pressureregulator and
filter unit
Air pressureadjusting knob
Oil removalfilter unit
Filter bowldrain outlet
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-8 Maintenance – air regulator unit
Removing and refitting filterelements
Regularly inspect the filter elements. They shouldbe replaced when dirty or wet and at least onceeach year. Do this as follows:
1. Switch off the air supply.
2. Unscrew the filter bowl by hand.
3. Remove the O-ring from the recess in thefilter bowl. Discard the O-ring.
4. Unscrew and remove the filter element.
5. Fit the replacement filter and, whereapplicable, the O-ring. These are shown indotted box A in the figure on the next page.
6. Fit a new O-ring into the recess in the filterbowl.
7. Refit the filter bowl and screw hand tight.
8. Switch on the air supply and set the pressureto 2 bar (29 psi).
Air pressureregulator filter
bowl
Oil removalfilter bowl
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-9Maintenance – air regulator unit
NOTE: Items shown within dottedboxes A and B are included in the airfilter service kit obtainable fromRenishaw (see the parts lists on pages1-23 to 1-24 and 1-32 to 1-34).
Replacing other servicekit components
1. Switch off the air supply.
2. Using a 38 mm A/F spanner,remove the regulator head.
3. Remove the components (shown indotted box B in the figure) from thebody of the regulator.
4. Fit the new components to theregulator body.
5. Refit the regulator head and tightento 7.7 Nm (5.7 Ibf.ft).
6. Switch on the air supply and set thepressure to 2 bar (29 psi).
A
B
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-10 Installation – base and side mounting options
M12 (½ in)screw (notsupplied)
M10 (3/8 in)screw andwasher (notsupplied)
M4 screws(not supplied)
Adjuster block
Washer
M4 side mountingarrangement
M4 screws(supplied)
M4 screws(not supplied)
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-11Installation – angled mounting option
Angled adjuster block(see the parts lists onpages 1-23 to 1-24 and1-32 to 1-34 for orderingdetails)
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-12 Installation – mounting the unit
Mounting the unit
1. When an adjuster block is to be used formounting the NC unit, loosely secure theblock to the bed of the machine.
Carefully align the block with the X or Y axisof the machine then fully tighten the securingscrew(s). Recheck the alignment is parallelwithin 1 mm of the X or Y axis.
2. On the NC unit, unscrew the M4 adjustingscrew so that the thread protrudesapproximately 1.5 mm from the base of theNC unit.
3. Position the NC unit on the adjuster block andevenly tighten the three M4 securing screwsto 1.3 Nm (0.96 lbf.ft).
NOTE: See page 1-20 for instructions on aligningthe NC2 and page 1-27 for instructions onaligning the NC3.
M4 securingscrews
M4adjusting
screw
Adjuster block
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-13
!
Installation – air supply
Air supply
The air supply to the NC unit must conform toISO 8573-1 air quality of class 1.7.2 and bemoisture-free. If the air quality cannot beguaranteed, an optional air filtration unit isavailable from Renishaw – see the parts lists onpages 1-23 to 1-24 and 1-32 to 1-34.
The NC unit requires a continual regulated airsupply of between 1.5 bar (21.75 psi) minimumand 6 bar (87 psi) maximum, with arecommended pressure of 2 bar (29 psi).
Failure of the air supply may cause the NC unit tobecome contaminated. If contamination issuspected (denoted by the NC unit’s LEDflickering or showing permanently red) carry outthe cleaning procedure (see “Cleaning” on page1-4).
CAUTION: Do not connect the NC unit toan oiled air supply. Purge all piping priorto connection.
Connecting and purging the airsupply
CAUTION: Safety glasses must be worn.
1. Connect a suitable pipe to the air supply.
2. Before connecting the pipe to the inlet of theair regulator unit, briefly switch on the airsupply to clear out any debris from the pipe.When no more debris is emitted from thepipe, switch off the air supply.
3. Connect the pipe to the inlet of the airregulator unit.
4. Insert one end of the 4 mm air pipe into theair regulator.
5. Cut the 4 mm pipe to length and connect it tothe M4/M3 adaptor. Make sure the length ofthe pipe is as short as possible to minimisethe drop in air pressure.
!
(continued on page 1-15)
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-14 Installation – air supply
To NCi-4interface
Electrical cable
2.0 bar
90° conduitadaptor
Conduitadaptorsecuringscrews
Air outlet
Air pipe
Electricalcable
Air regulator unit
Purge air supply to dislodgedebris from pipework prior toconnection as small particlesmay block the air nozzle.
Adaptor
Ø3 mm air pipe
Ø4 mmair pipe
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-15
6. Insert one end of the 3 mm air supply pipeinto the M3/M4 adaptor.
7. Push the free end of the air supply pipethrough the conduit and conduit adaptor.
8. Cut the 3 mm pipe to length. Make sure thelength is as short as possible to minimise thedrop in air pressure.
Installation – air supply
9. Before connecting the pipe to the inlet of theNC unit, briefly switch on the air supply toclear out any debris from the pipe. When nomore debris is emitted from the pipe, switchoff the air supply.
10. Insert the air supply pipe into the air inlet ofthe NC unit.
11. Switch on the air supply.
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-16 Installation – conduit adaptor and conduit
Fitting the conduit adaptor andconduit
1. Push the NC unit cable through the conduit.
2. Slide the conduit adaptor over the ridgedsecuring ring on the NC unit.
3. Evenly tighten the two M5 screws on the topface of the conduit adaptor and the single M5screw on the underside of the adaptor to1.5 Nm (1.1 lbf.ft).
4. Push the conduit over the barb on the conduitadaptor.
5. Slide the ‘O’ clip over the conduit.
6. Use a pair of pincers to pinch the ‘O’ clip ontothe conduit.
‘O’ clip
Pincers
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-17
Securing the conduit
In some instances, straining of the conduit cancause small movements of the NC2/NC3 unit.Such movements will result in poor repeatability. Ifthe conduit is able to move relative to the NC2/NC3 unit it should be firmly secured to themachine table.
1. Use the ‘P’ clips (part no. P-CL36-0016) tosecure the conduit in a fixed position on thetable of the machine (see the figure below).
‘P’ clips
Installation – conduit adaptor and conduit
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-18 NC2 general
Introduction
This section of the guide describes how to installand maintain the Renishaw NC2 non-contactbroken tool detection system.
The NC2 is a laser-based non-contact toolbreakage detection system specifically designedfor solid centred tools, for example drills and taps.
The tool is moved into the beam, the output isactivated by the latch input line, and the NC2“latches” the output if light is detected upon thereceiver.
Software routines
Examples of programs for high-speed broken tooldetection of solid tools are available for a widerange of machine controller types. Please refer tothe Renishaw website at www.renishaw.com andthen search for “NC2 software”.
Power supply
The NC2 can draw its power from the CNCmachine’s 12 V to 24 V nominal d.c. supply. Itsinput voltage range is 10 V d.c. to 30 V d.c.maximum and it presents a load of up to 35 mA.
Alternatively, the NC2 can be powered from aRenishaw PSU3 power supply.
Cleaning
Cleaning may be required if the air to the NC2becomes contaminated or if the system is leftwith the air off when coolant is present.
Excessive contamination will block the laserbeam and prevent the NC2 from functioning. Inthis condition broken tools will not be identifiedand the LED will be permanently lit red.
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-19NC2 specification
Application High-speed non-contact tool breakage detection of solid tools
Working temperature 5 °C to 50 °C
Storage temperature -10 °C to 70 °C
IP rating IPX8 with air on
Life Tested to > 1 million on/off cycles
Tool diameter Ø0.15 mm (0.059 in) min., Ø80 mm (3.15 in) max.
Pneumatic supply Ø3 mm air pipe, 1.5 bar (21.75 psi) min., 6 bar (87 psi) max.,2 bar (29 psi) recommended.Air supply to the NC2 air regulator unit must conform to ISO 8573-1: Class 5particulates and moisture free.
Current consumption 35 mA max.
Cable 6-core plus screen cable. Each core 18/0.1 insulated.Ø6.0 (0.24 in) x 10 m (32 ft)
Weight 0.75 kg (1.65 lb)
Mounting Single M10/M12 fixing.M4 mounting holes also provided.
Input voltage 10 V to 30 V
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-20
Achievable set-up tolerances
The tolerance to which a tool can be checked isdependent on the perpendicularity of the laserbeam to the machine spindle axis.
A typical perpendicularity value sufficient for mostapplications is as follows:
spindle axis ≤ 0.1 mm
This value can be refined to suit individualapplications.
Aligning the NC2
Aligning the NC2 involves making smalladjustments to the unit in the Z-axis until the laserbeam is perpendicular to the machine Z-axiswithin the set-up tolerance. This determines theminimum length of broken tool which can bedetected.
To check the perpendicularity of the beam,determine its position at two points – P1 and P2(see below).
NOTE: It is recommended that the distancebetween P1 and P2 is at least the size of themaximum tool diameter.
Use a piece of flat-bottom ground bar of knownlength and diameter held in the spindle. Manuallywind the calibration pin into the beam at P1 andP2 and monitor the status LED to determine thebeam position (green indicates that the beam isnot broken, red that the beam is broken).
NC2 alignment
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-21
Determining the checking position
The centre line of the beam has to be determinedfor use by the high-speed tool detection program.
1. At a point approximately midway between P1and P2, manually wind the calibration pin intothe laser beam from above.
2. Use the LED to determine the beam positionat this point. It should be possible to find theposition within 10 µm.
3. Repeat steps 1 and 2 to find the left and righthand sides of the laser beam. The midpointbetween these points is the beam centre line.
4. Input this checking position into the memorylocations accessed by the high-speed tooldetection program.
NC2 alignment
To adjust the beam, raise or lower the receiverend of the NC2 as follows:
1. Slacken the single securing screw at thereceiver end.
2. To raise the receiver end of the NC2, tightenthe adjusting screw.
To lower the receiver end of the NC2, loosenthe adjusting screw.
3. Gently tighten the single securing screw.
Now determine the position of the beam again atP1 and P2, repeating steps 1 to 3 as appropriateuntil the required perpendicular alignment isachieved.
After alignment has been achieved, tighten thesingle securing screw to 1.3 Nm (0.96 lbf.ft).
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-22
The SSR output is protected by a resettable fuse.To reset, remove the power and the cause of thefault.
NOTE: Connect the screen to the machinecontroller protective earth (also referred to as‘PE’, ‘starpoint’ or ‘Earth plate’).
High-speed tool breakage detectionon/off
An M-code is required to activate the toolbreakage function. The M-code must supply aconstant voltage of 10 V to 30 V to the grey wire.To deactivate the tool breakage function, the greywire is returned to 0 V.
NC2 connections
NC2
{Powerinput
{Statusoutput
Voltagefree SSR
CNC controller
+10 V to 30 V d.c.
0 V d.c.
M-code +10 V to 30 V d.c.
I/O supply
skip input (G31) / machine input
screen
Controller protective earth
} Powerto NC2
Controller reference ground
red
black
purple
grey
white
blue
green
Electrical connections: NC2 to machine controller
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-23
epyT rebmuntraP noitpircseD
2CN 0051-2315-A resal,ediugnoitallatsni,elbacm01,ylbmessa2CNngisgninraw
tik2CN 0001-2315-A resal,tikloot,kcapretsujda,elbacm01,ylbmessa2CNdnarotalugerria,tiudnoc,ediugnoitallatsni,ngisgninraw
epipria
tiklooT 0030-9714-A .xehF/Amm0.3,hcnerw.xehF/Amm5.2,rennapsniPhcnerw
tikylbmessariA 0061-9714-A sgnittifriahtiwmm4Øotmm3ØretlifrotalugerriAepipriamm3Øxm5dnaepipriamm4Øxm52
tikecivresretlifriA 200S-10IF-P slwobretlifhtobrofstrap-rotalugerriaroftikecivreS
retlifriaexuleD 8000-10IF-P niardotuadna'noitacidniretlifdekcolb'htiwrotalugerriA
kcolbretsujdadelgnA 1051-9714-A elbatlootenihcamehtno2CNehtelgnaotkcolB
ediugnoitallatsnI 6915-0002-H ediugnoitallatsnI
dediarbleets,tiudnoC 8000-10OH-P ertemrepdlos-diarbleetshtiwesohCVPmm71Ø
nolyn,ebuT 1610-9714-M recudermm3otmm4htiw)gnolm5(ebutnolynmm3Ø
tikelzzonriA 0540-9714-A dna,tinureviecerdnatinurettimsnartrof)ffo2(spacriArennapsnip
pilc-O 5400-10AM-P pilc-O
tunkcoL 6100-90UN-P tunkcol5.1x61M
3USP 8100-9102-A )0022-0002-Hteehsatadees(tinuylppusrewop3USP
NC2 parts list
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-24 NC2 parts list
epyT rebmuntraP noitpircseD
dnalgtiudnoC 3600-16AC-P dnalgtiudnoc11PG
gniknalbdnalgtiudnoCgulp
4600-16AC-P gulpgniknalbdnalgtiudnoC
pilc-P 6100-63LC-P mm61ØpilcgnibuT
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-25
Recommended feedrates
It is recommended that a feedrate of 2 µm-per-rev.is used for a minimum of three measuring moves.A span of 5 µm over three measurements isachievable.
Software routines
Software routines for tool setting using variousmachine controllers are available from Renishaw.They are described in data sheet H-2000-2289(see www.renishaw.com).
Introduction
This section of the guide describes how to installand maintain the Renishaw NC3 non-contact toolsetting system.
The NC3 is a laser-based non-contact tool settingsystem that provides high-speed/high-precisionmeasurement of cutting tools on a machiningcentre under normal operating conditions.
As a tool moves through the laser beam, thesystem detects when the beam is broken. Outputsignals sent to the controller allow the presenceof a tool and the position of the tip (broken tooldetection) to be established.
Status LED
The LED on the NC3 indicates the status of thelaser beam:
Green = Laser beam is unobstructed
Red = Laser beam is obstructed.
NC3 general
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-26 NC3 specification
Application High-precision / high-speed non-contact tool setting and tool breakagedetection
Working temperature 5 °C to 50 °C
Storage temperature -10 °C to 70 °C
IP rating IPX8 with air on
Repeatability of triggerpoints
±0.15 µm (±6 µin) 2σ
Life Tested to > 1 million on/off cycles
Tool diameter Tool setting: 0.20 mm (0.008 in) min., 80 mm (3.15 in) max.,101.6 mm (4.00 in) off-centreTool breakage: Ø0.1 mm (0.04 in) min.
Pneumatic supply Ø3 mm air pipe, 1.5 bar (21.75 psi) min., 6 bar (87 psi) max.,2 bar (29 psi) recommended. Air supply to the NC3 air regulator unitmust conform to ISO 8573-1: Class 5 particulates and moisture free.
Current consumption(including NCi-4 interface)
120 mA @ 12 V, 70 mA @ 24 V
Cable 6-core plus screen cable. Each core 18/0.1 insulated.Ø6.0 (0.24 in) x 10 m (32 ft)
Weight 0.75 kg (1.65 lb)
Mounting Single M10/M12 fixing.M4 mounting holes also provided.
Supply protection Resettable fuses. Reset by removing power and cause of the fault.
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-27
Achievable set-up tolerances
Tool setting applications
The tolerances to which a tool can be set isdependent on the parallelism of the laser beam tothe machine axes. A value of 5 µm over a span of50 mm perpendicular to the Z-axis and 1 mm tothe X or Y-axis is easily achievable. This settingaccuracy is sufficient for the majority of toolsetting applications.
Tool breakage detection
A value of less than 0.1 mm (0.0039 in) maximumover a span of 50 mm perpendicular to the Z-axisand 1 mm with X or Y-axis is achievable. Thisshould be sufficient for the majority of toolbreakage applications.
NC3 alignment
Aligning the NC3
Aligning the NC3 involves making smalladjustments to the unit in the Z-axis until the laserbeam is parallel to the machine X or Y-axis withinthe set-up tolerances.
You will need to run the Renishaw NC softwarebeam alignment cycle before physically aligningthe NC3 (for details of this cycle, refer to theRenishaw non-contact tool setting systemprogramming guide).
After running this cycle, you will be able toascertain whether the laser beam is parallel to themachine X or Y axis or whether the receiver endof the NC3 needs to be raised or lowered withrespect to the transmitter end.
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-28
To raise or lower the receiver end ofthe NC3
1. Slacken the single securing screw at thereceiver end.
2. To raise the receiver end of the NC3, tightenthe adjusting screw.
To lower the receiver end of the NC3, loosenthe adjusting screw.
3. Gently tighten the single securing screw.
4. Run the beam alignment cycle again todetermine whether the beam is parallel to themachine X or Y-axis or whether furtheradjustments need to be made to the NC3.
Repeat steps 1 to 3 as appropriate.
5. After alignment has been achieved, tightenthe single securing screw to 1.3 Nm(0.96 lbf.ft).
NC3 alignment
M4 securingscrews
M4adjusting
screw
Adjuster block
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-29
!
Installation – NCi-4 interface
Introduction
The NCi-4 interface should be installed in theCNC control cabinet. Where possible, locate theunit away from potential sources of interferencesuch as transformers and motor controllers.
The interface processes signals from the NC3and converts them into a voltage-free solid staterelay (SSR) output. This is transmitted to theCNC machine control, which responds to theprobe inputs.
Installing the interface
WARNING: Before installing the NCi-4interface, ensure the machine is safe to
work on. Switch off machine power when workingin the control cabinet.
Install and configure the NCi-4 interface asdescribed in the publication “NCi-4 installationand user’s guide”, Renishaw part no.H-2000-5236.
What to do next
After you have finished installing the NCi-4interface, apply electrical power to the interface.
After the interface has been powered, switch onthe air supply and set the air pressure.
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-30
!
Installation – applying electrical power
Applying electrical power tothe interface
WARNING: Before switching onelectrical power, ensure the machine is
safe to work on.
1. Ensure that the NCi-4 interface and airsupplies have been connected correctly.
2. Switch on electrical power to the interface.
3. Check that the status LED on the NC3 unit islit.
Power loss and restoration
If electrical power to the NCi-4 interface is lostand then subsequently restored when the NC3system is in a normal operating mode, the NC3powers down and then powers up again withoutloss of the original gain settings.
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-31
NC3
Wiring – NC3 system
✸ Note that some early NC3 units do nothave a purple coloured wire but have oneadditional black wire. Both black wires should beconnected to pin 7.
NCi-4 connector CN1
Not used
Spare 0 V
Spare 12 V to 24 V
Analogue output 1
Analogue output 2
0 V
+12 V
Ground
NC3 White
Purple ✸
Blue
Black ✸
Red
Screen
Grey
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-32 NC3 parts list
Type Part number Description
NC3 A-4179-1500 NC3 assembly, 10 m cable, installation guide, laserwarning sign
NC3 kit A-4179-1100 NC3 assembly, 10 m cable, NCi-4 interface, adjusterpack, tool kit, laser warning sign, installation guide,conduit, air regulator and air pipe
NCi-4 interface A-5259-1000 NCi-4 interface and box with DIN rail mounting and twoterminal blocks
NCi-4 terminal block(10-way)
P-CN25-1053 10-way socket terminal for NCi-4 interface
NCi-4 terminal block(15-way)
P-CN25-0009 15-way socket terminal for NCi-4 interface
Tool kit A-4179-0300 Pin spanner, 2.5 mm A/F hex. wrench, 3.0 mm A/F hex.wrench
Air assembly kit A-4179-1600 Air regulator filter Ø3 mm to Ø4 mm with air fittings,25 m x Ø4 mm air pipe and 5 m x Ø3 mm air pipe
Air filter service kit P-FI01-S002 Service kit for air regulator - parts for both filter bowls
De luxe air filter P-FI01-0008 Air regulator with 'blocked filter indication' and auto drain
Angled adjuster block A-4179-1501 Block to angle the NC3 on the machine tool table
Installation guide H-2000-5196 Installation guide
Conduit, steel braided P-HO01-0008 Ø17 mm PVC hose with steel braid - sold per metre
Tube, nylon M-4179-0161 Ø3 mm nylon tube (5 m long) with 4 mm to 3 mm reducer
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-33NC3 parts list
epyT rebmuntraP noitpircseD
tikelzzonriA 0540-9714-A nipdna,tinureviecerdnatinurettimsnartrof)ffo2(spacriArennaps
pilc-O 5400-10AM-P pilc-O
tunkcoL 6100-90UN-P tunkcol5.1x61M
tiudnocthgiartSrotcennoc
1530-9714-A rotpadatiudnoc°09secalpeR
dnalgtiudnoC 3600-16AC-P dnalgtiudnoc11PG
dnalgtiudnoCgulpgniknalb
4600-16AC-P gulpgniknalbdnalgtiudnoC
pilc-P 6100-63LC-P mm61ØpilcgnibuT
tikerawtfosCN)cunaF(
0280-2104-A ,srellortnocIMdnaM12-61,51-01,6,0cunaFroferawtfoSediuggnimmargorp
tikerawtfosCN)kazaM(
2600-3104-A ,srellortnocsulP-Mdna23M,046noisuFkazaMroferawtfoSediuggnimmargorp
tikerawtfosCN)saaH(
5980-2104-A ediuggnimmargorp,srellortnocsaaHroferawtfoS
tikerawtfosCN)cansaY(
0200-4104-A ,srellortnoc003Jdna08I,05J,3XMcansaYroferawtfoSediuggnimmargorp
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
1-34 NC3 parts list
epyT rebmuntraP noitpircseD
tikerawtfosCN)snemeiS(
7510-4104-A ,srellortnocD048dnaD018snemeiSroferawtfoSediuggnimmargorp
tikerawtfosCN)niahnedieH(
5610-4104-A ,srellortnoc034dna624niahnedieHroferawtfoS)ylnoMEO(ediugnoitargetni,ediuggnimmargorp
tikerawtfosCN)035iniahnedieH(
3220-4104-A ,ediuggnimmargorp,rellortnoc035iniahnedieHroferawtfoS)ylnoMEO(ediugnoitargetni
tikerawtfosCN)sadleMihsibustiM(
0500-3104-A dna533M,023M,013M,3MsadleMihsibustiMroferawtfoSediuggnimmargorp,srellortnoc005M
tikerawtfosCN)rehtorB(
4090-2104-A ,noitpoorcamhtiwdettif,srellortnocrehtorBroferawtfoSediuggnimmargorp
tikerawtfosCN)yeldarBnellA(
5201-6104-A ,rellortnoc)01seires(IASOyeldarBnellAroferawtfoS)ylnoMEO(ediugnoitargetni,ediuggnimmargorp
tikerawtfosCN)ihcatiH(
0480-2104-A M81dnaM61amgiSroferawtfoS
tikerawtfosCN)onikaM(
0090-2104-A M81-61cunaFottnelaviuqe-3orProferawtfoS
tikerawtfosCN)amukO(
1201-6104-A M001UdnaM01U,M0007/M007amukOroferawtfoSediuggnimmargorp,srellortnoc
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
4-34 Elenco delle parti NC3
opiT etrap.N enoizircseD
CNerawtfostiK)saaH(
5980-2104-A enoizammargorpidadiug,saaHillortnocreperawtfoS
CNerawtfostiK)cansaY(
0200-4104-A idadiug,003Je08I,05J,3XMcansaYillortnocreperawtfoSenoizammargorp
CNerawtfostiK)snemeiS(
7510-4104-A idadiug,D048eD018snemeiSillortnocreperawtfoSenoizammargorp
CNerawtfostiK)niahnedieH(
5610-4104-A idadiug,034e624niahnedieHillortnocreperawtfoS)MEOolos(enoizargetni'llaadiug,enoizammargorp
CNerawtfostiK)035iniahnedieH(
3220-4104-A idadiug,035iniahnedieHollortnoclireperawtfoS)MEOolos(enoizargetni'llaadiug,enoizammargorp
CNerawtfostiK)sadleMihsibustiM(
0500-3104-A ,023M,013M,3MsadleMihsibustiMillortnocreperawtfoSenoizammargorpidadiug,005Me533M
CNerawtfostiK)rehtorB(
4090-2104-A adiug,orcamenoizpoiditatod,rehtorBillortnocreperawtfoSenoizammargorpid
CNerawtfostiK)yeldarBnellA(
5201-6104-A adiug,)01eires(IASOyeldarBnellAollortnoclireperawtfoS)MEOolos(enoizargetni'llaadiug,enoizammargorpid
CNerawtfostiK)ihcatiH(
0480-2104-A M81eM61amgiSillortnocreperawtfoS
CNerawtfostiK)onikaM(
0090-2104-A M81-61cunaFaitnelaviuqe-3orPillortnocreperawtfoS
tikerawtfosCN)amukO(
1201-6104-A ,M001UeM01U,M0007/M007amukOillortnocreperawtfoSenoizammargorpidadiug
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM
Renishaw plcNew Mills, Wotton-under-Edge,Gloucestershire, GL12 8JRUnited Kingdom
T +44 (0)1453 524524F +44 (0)1453 524901E [email protected]
For worldwide contact details, pleasevisit our main website at
www.renishaw.com/contact
C-CON, INC. - (972) 726-7002 - WWW.C-CONINC.COM