Renault Store - Technical specifications The configurator · 2017. 1. 16. · Renault Store /...
Transcript of Renault Store - Technical specifications The configurator · 2017. 1. 16. · Renault Store /...
© Renault Brand Stores - July 2015
Renault Store - Technical specifications
The configurator
2
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Contents
Contents
General
Introduction 4
Colours & materials 5
Technical principles
General description 7
Detailed description 12
Multimedia unit and screen 13
IT equipment wiring diagram 16
Bodywork shade samples 18
Upholstery samples 20
Wheel rims and wheel trims 22
General assembly diagram 26
General
4
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / General
Introduction
The configurator allows customers to find out about the range of shades and options available to customise the vehicle of their choice.
In this way, with the help of the sales advisor or independently, customers can complete the configuration of their vehicle using the samples on display: shades, upholstery and wheel rims.
A touch screen completes configuration and establishes a link between the virtual and the physical elements. This unit must systematically be positioned in the visitor flow and near sales desks where possible.
Composition of configurator:
1 A unit2 A touchscreen3 A communications message4 A paintwork palette5 An upholstery sample holder6 Two wheel rims7 A wheel trim
1
2
3
4
5
6
7
5
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / General
Typeface Renault Life
Branding and texts Refer to the «Showroom communications» specifications
Colours & materials
RAL 9003 satin white
- Lightweight particle board panel with white melamine veneer in EGGER W1000 ST9 premium white
- White PVC veneer edges- Lacquered aluminium
Dark grey equivalent to RAL 7024
- Particle board panel with melamine finish in EGGER U963 ST15 diamond grey
- Lacquered steel- Solid-coloured PVC
Pantone 426 EC grey
- Branding- Satin or matt adhesive
Pantone 185 EC red
- Branding- Satin or matt adhesive
Technical principles
7
Le configurateur vous guide !C’est simple.
Habillez votre Renault aux couleursde vos envies.
Un, deux, trois... Et votre Renaultdevient unique.
LES TEINTES DE CARROSSERIE ET LES SELLERIES
Les teintes de base Les teintes métallisées Les jantes en alliage
LES JANTES
Les teintes spéciales
Les enjoliveurs
Les jantes spéciales
8 1191041 6 73 52 125
60 601200
1840
201
8
6060
20
900 1200
3420
8 1191041 6 73 52 125
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Front view1 Lightweight particle board panels, 60 mm thick
White melamine veneer in EGGER W1000 ST9 premium white, veneered white PVC edges
2 Adhesive markings in Pantone 185 EC red and black Satin or matt finish (refer to the «Showroom communications» specifications).
3 Particle board panel, 20 mm thick White melamine veneering of front panel, EGGER W1000 ST9 premium white
4 32" LED multi-touch screen5 Edge-to-edge joint seams between panels6 Front of the unit Particle board panel, 20 mm
thick Dark grey melamine finish in EGGER U963 ST15 diamond grey
7 Colour strips8 RAL 7024 dark grey lacquered brackets for the
colour strips9 Suspension rail, 12 mm diameter RAL 7024 dark
grey lacquered aluminium Room for four rails per unit
10 Textile and leather samples on ABS plastic hanging rail (not supplied)
11 Plinth inset by 20 mm Water-repellent particle board panel with PVC veneered edges. Finish same as for attachment plate.
12 Steel attachment plate, 5 mm thick RAL 7024 dark grey lacquered steel sheet with rounded-off edges.
General description
8
1100 6060 11001100
1550
3420
1550
1
2
3
4
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Back view1 Lightweight particle board panels, 60 mm thick
White melamine veneering of outer surfaces, EGGER W1000 ST9 premium white, straight edges White PVC veneer edges
2 Plinth inset by 20 mm Water-repellent particle board panel with PVC veneered edges Finish same as for attachment plate, RAL 7024 dark grey
3 Steel attachment plate, 5 mm thick RAL 7024 dark grey lacquered steel sheet
4 Particle board panel, 20 mm thick White melamine veneer in EGGER W1000 ST9 premium white
NOTE: This panel may be used for communications about a nearby vehicle (POS display).
General description
9
1998
20
2018
300
3420
3460
2020
600
60
VUE DE CÔTÉ COUPE BB’ (vue de côté) COUPE AA’ (vue du dessus)
1154
350
650
22060 20
AA’
BB’
2
5
1
8
6
8
8 8
8
7
3
4
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
General description
Side views and cross-sections
Integration of the screenThe screen is affixed on the front of the configurator using a bracket compliant with the 200 x 400 VESA standard.
A hole measuring approximately 350 x 650 mm in the front panel of the unit allows cable routing and embedding. Heat is removed through the top of the unit via an exhaust vent in the top.
Key1 Attachment plate with rubber pads2 Exhaust vent3 32" touch screen4 Metal screen bracket5 IT equipment access hatch6 Back of the unit
Particle board panel, 20 mm thick7 Front of the unit
Particle board panel, 20 mm thick8 Unit housing, 60 mm thick
Lightweight particle board panel White melamine finish White PVC veneer edges
SIDE VIEW BB’ CROSS-SECTION (side view) AA’ CROSS-SECTION (top view)
10
3460
1154 11541154r.10
1154
= 900
3460
=
Face arrière
r.10
CONFIGURATION STANDARD
ADAPTATION
300r.10
1154
150
1 2 3 4
1 2 3 4
5 6
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
General description
Attachment platesThe base of the configurator comprises three identical attachment plates, 1154 mm long.
A 300 x 100 mm hole is drilled in each attachment plate for the routing of power cables.
Edges should be rounded off slightly following cutting to avoid any risks to personnel in the dealership.
The attachment plate shall be equipped with pads to avoid damaging floors.
Principle of adaptationWhere the configurator is installed at the back of the canopy, the central plate shall be cut at the back to allow the base of the canopy to pass through it.
The cut-out will be of the following size: l. 900 mm x w. 150 mm.
Key1 Central attachment plate2 Plinth inset by 20 mm3 Edge of the unit4 Screen5 Cable routing6 Drill holes to fasten wooden parts to the
attachment plate
STANDARD CONFIGURATION
ADAPTATION
Back side
11
2 3 4 5 8 976 12 1411 13101
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Schematic exploded view
1 IT equipment access hatch RAL 9003 white 2 mm aluminium
2 Steel attachment plate, 5 mm thick RAL 7024 dark grey lacquered steel sheet
3 Plinth inset by 20 mm Water-repellent particle board panel with PVC veneered edges. Finish same as for attachment plate.
4 Adhesive markings5 32" LED touch screen6 Dark grey lacquered screen bracket7 Textile and leather samples on ABS plastic
hanging rail (not supplied)8 Colour strips (not supplied)9 Front of the unit Particle board panel, 20 mm
thick Melamine finish10 Back of the unit Particle board panel, 20 mm
thick Melamine finish11 Lightweight particle board panels, 60 mm thick
Holes drilled for power supply routing12 Inside décor of the background particle board
panel, 20 mm thick, dark grey melamine13 Lightweight particle board panels, 60 mm thick
White melamine veneering of outer surfaces, EGGER W1000 ST9 premium white White PVC veneer edges
14 Longitudinal vent or holes
12
60 6070
55 85
900 80
550
6047
055
0
448 7070 799 331 230
6023
264420
028
480
7443
0
422020
2020
2020
2013
013
013
013
013
013
013
070
405
717
405530
2050Ecran maxi 760 mm 518 869 391 20
405 40541 41 41
70
787= =
12,5 12,516
70Screen max. 760 mm
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Detailed description
13
786.14
480.74
698.7
393.3
4469
25.2
105.94
590
280.2
69 194
250
40
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Multimedia unit and screen
1 32" touch screenExample: iiyama T3234MSC700 x 390 mm formatResolution 1920 x 1080
NB. Ensure that the dimensions of the chosen screen are fully compatible with the fastening system. Check that the screen has a sufficient resolution to support display of content in at least HD quality.
2 Multimedia unitMultimedia unit for displaying video content on the screen in conjunction with a content delivery management solution.
The specifications of this unit are to be determined in consultation with the supplier of the content management solution. It is also necessary to ensure that the dimensions of the cabinet and the unit are compatible.
Example: Quanmax MVP225 player deployed for the central digital solution. 1 2
14
29
7
60
20
0
4 5 0
5
d.7 débouchant
3 0 0
( c e n tr é ) 5 0
20
( c e n tr é )d.7
11
4 1 0
( c e n tr é )
4 x
3
X
4 5°
Chanfrein
4 x
5
X
45 °
Chanfrein
8
17
90°4 0 0
( c e n tr é )
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Screen bracket (1)
Bracket fastened to the back of the screenThis bracket is made of sheet steel. It has a 90° bend at the top to enable it to be bolted to the wall-mounted section fastened to the front of the configurator.
400 (centered)
300 (centered)
chamfer
chamfer
hole
20 (centered)
15
30
3
2 7
1 5
4 5 0
6
4 10
( c e n tr é )
2 0
27
90°
53 ,52 9 6 ,5
( c en tr é )
9 3,5212 écrous sertis ou soudés M6
4 x 5 x 45° Chanfrein
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Wall bracket fastened to the front of the configuratorThis bracket is made of sheet steel. It has a 90° bend at the top to which two bolts are attached for fastening the screen bracket.
Screen bracket (2)
2 M6 crimped or welded nuts
296,5 (centered)
296,5 (centered)
4 x 5 x 45° chamfer
16
COUPE AA’ COUPE BB’ CÔTÉ GAUCHE
400
120
r. 10
AA’
18080 40 15050 90
5
7
2
6
1
8
4
3
1
2
9
5
9
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
IT equipment wiring diagram
Power supply routing (red)The power supply inlet passes through the attachment plate. A connection box is installed at the bottom of the unit.Two RJ 45 Ethernet cables run alongside the general power cable.
Distribution (blue)The power cable travels up through the inside of the unit to a socket board.
Ethernet wiring (yellow)The multimedia unit and touch screen are connected to the local network via an Ethernet cable.
Screen connectionAn HDMI cable and RS 232 cable connect the multimedia unit to the screen.The touch screen is connected to the screen via an HDMI cable.1 Power supply inlet2 Connection box3 Plug socket board (5 sockets)4 Multimedia unit5 Screen6 HDMI cable7 RS 232 cable8 RJ 45 Ethernet cable9 Power supply AA’ CROSS-SECTION BB’ CROSS-SECTION LEFT SIDE
17
A
(
1 : 1 )
400
130
26
75
14,5
14,5
45°
2
12
15,5
15
120°
32x
Ch.
à
45°
soudure
par
point
face
visible,
aucune
trace.
8035
30
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
IT equipment access hatch
PrincipleThe drawings opposite show the hatch providing access to the electrical wires routed through the attachment plates.
The design of this element may be adapted if necessary depending on the type of internal frame structure developed by each supplier but the overall dimensions must be retained to allow hands to pass through the opening provided.
spot welding
apparent sideno traces
18
17
972054 ==
20 17 3
1720
2013
0
779
4
Entretoise
Le supportse termine
10 mmavant le bord
de la plaque�e
Le vis de fixationdu support des
plaque�essont masquées
par les plaque�es
428
311
Prévoir un rayon r. 1 mm
pour faciliter la mise en place
de la plaque�e10
10
= =
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Bodywork shade samples
Brackets Allow a radius of 1 mm to facilitate fitting of the strip.
The bolts fastening the strip brackets are hidden by the
strips.
There is a 10 mm gap between the bracket and the
edge of the strip.
Spacer
19
LES TEINTES DE CARROSSERIE
Les teintes de base Les teintes métallisées Les teintes spéciales Les jantes en alliage
Les jantes spéciales
Les enjoliveurs
LES JANTES
727
ENR
460
ENW
QXB
489
RPE
423396
NNL
719
QNG
C70
369
RNQ
D31 D32D16
RPS
RPC
144
D14 D17 QNCD37 RNT RPH
HXA
RNL RNU
CNF
J43
KXC
CNG
NNM NXE
QNF QXA
676472 B66 ENVC66 J37CNB
KNG
CXA
KNH KNR
KNV KNX
D68
RNW RNY
W XC
266
LNE
D92 GNDGNAG64 GNE
HNK
D69
RNT
NNJ
31
EXEMPLE DE PLAN D’IMPLANTATION DES ÉCHANTILLONS
LES SELLERIES
HNP
D47
NNP
RPJ
0
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Bodywork shade samples
Layout principlesEach bodywork sample has a given position on the front panel of the configurator.
The number of samples on display is specific to each country.
The samples may be updated or new samples may appear depending on changes to the range.
Each supplier should ensure that they have the up-to-date general sample layout plan at their disposal when the unit is delivered to the dealership.
NOTE: The colour strip brackets are a standard length, which means that new shades can be added if necessary.
BODYWORK SHADES
UPHOLSTERY
EXAMPLE OF SAMPLE LAYOUT PLAN
Basic shades Metallic shades Special shadesAlloy rims
Special rims
Wheel trims
WHEEL RIMS
20
3535 55
125
AA’ BB’ CC’
ECHANTILLONPLAN DE LA BARRE SUPPORT D’ECHANTILLONS
d.5
430
430
60 60
r.4
60 60
2,3 313r.7
11
55 72,5 55 72,5 55
2
12,5 1,5
92,5°
CC’BB’AA’
r.34
3
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Upholstery samples
Display railThe upholstery samples are displayed on an injected ABS rail that can hold three sets of samples across an overall length of 430 mm.
These samples are cut to a 125 x 200 mm format with serrated edges and bolted to the rail.
The rails have notches at each end, giving two 12 mm axes 405 mm apart.
The company SURVIVAL supplies rails and samples and ensures that upholstery samples are updated according to new references.
http://www.sampleselector.com
DRAWING OF THE SAMPLE BRACKET RAILSAMPLE
21
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Upholstery samples
Display rail bracketThe bracket for the upholstery sample rails is made by turning an aluminium bar.
This bar placed in an insert in the front of the unit.
The finish is a dark grey melamine finish in EGGER U963 ST15 diamond grey.
48 mm built-in
22
1998
20
2018
26020 20
3420
3460
2020
300
600
60
VUE DE CÔTÉ COUPE BB COUPE AA’
BB’
AA’
22060 20
2
3
6
7
1
8
4
5
ATTENTIONJante 16“
ATTENTIONJante 15“
ATTENTIONEnjoliveur pour
jante 16“
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Wheel rims and wheel trims
Integration of the wheel rimsThe rims are integrated into the unit, fastened to an attachment plate comprising fastening studs for the rim bolts (corresponding to the drill spacing of the rims).
This attachment plate is fastened at the back of the unit, with an adjustable sleeve to ensure the rim sticks out from the front of the unit by 38 mm regardless of its offset.
The front of the unit has a hole equivalent to the external diameter of the rim + 10 mm.
Integration of the wheel trimsThe wheel trims are fastened in the cut-out panel of the unit using their system of integrated metal tabs. The drilling of the front of the unit means only one diameter can be installed (corresponding to 15" or 16" wheel trims).
Key1 Attachment plate2 Front of the unit3 Rim attachment plate4 Attachment plate bracket5 Aluminium rim6 Inside of the unit7 Wheel trim8 Particle board
SIDE VIEW BB’ CROSS-SECTION
NOTE:16’’ rim
NOTE:15’’ rim
NOTE:Trim for 16’’ rim
AA’ CROSS-SECTION
23
10
7 2°
102 ,5
Vis M20 x 90 Filetage totalSoudure résistante
Brossage du chantou découpe azote
d. 120
5 x M14 x 2
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Wheel rims and wheel trims
Attachment plate for wheel rimsThis attachment plate allows for fine adjustment of depth to allow an identical offset of the wheel rim to be obtained in relation to the surface of the configurator regardless of the width of the wheel rim.
The number and the position of the drill holes (4 or 5) must be adapted to each type of wheel rim.
M20 X 90 bolt, fully threadedResistant weld
Bruches edgeor nitrogen-cut
24
200
200
3
d. 22
16 x d.5 mm
45
45
10
10
5
5
90°
Si laser :brossage du chant ou
découpe azote
Face d’appui :Soudures arrasées
résistantes
Ecrou M20 x 2,5soudé solidement
et bien à plat
Soudures résistantes
118
120 (centré)
120
(cen
tré)
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Wheel rims and wheel trims
Bracket for attachment plate on which wheel rim is mountedThe depth of this bracket may be adapted if necessary depending on the type of internal frame structure developed by each supplier.
If laser-cut:brushed edge or
nitrogen-cut
Resistant welded
120
(cen
tred
)
120 (centred)
M20 x 2.5 nut,solidly welded
and well-levelled
Bearing surface:levelled resistant
welds
25
1021
1895
19
310
474
1024
1574
440
420
410
VUE ARRIÈRE DU PANNEAU
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
Wheel rims and wheel trims
Wheel rim front panelEach country or region chooses the type of wheel rims to be displayed on the configurators.
The design of the front panel must be adapted to the diameters of the wheel rims and wheel trims selected.
The drawing opposite shows drilling of the panel adapted (from top to bottom) to 15 and 16-inch wheel rims, and a 16-inch wheel trim.
BACK VIEW OF PANEL
26
© Renault Brand Stores - July 2015
Renault Store / Technical specifications for configurator / Technical principles
General assembly diagram
PrincipleThe diagram opposite shows the general assembly principles for the unit to allow transportation of pre-assembled sub-assemblies.