CONTENT

PRECAUTIONS ...................1-2

USING THE REMOTECONTROL UNIT .....................3

OPERATION ........................4-9

Thank you forpurchasing ourRoom Air Conditioner.

Before using your air-conditioner, please read thisoperating instruction carefully and keep itfor future reference.

REMOTE CONTROL MANUAL

EN

GLI

SH

468040325/01

PRECAUTIONSPRECAUTIONS

DISPLAYInformation are displayed when the remote control unit is switched on.Operation Mode

AutomaticFan only

Heating CoolingDehumidification (dry)

Displayed when data trasmitted Or remote control unit lock

Displayed when the timer on is set and activatedDisplayed when the timer off is set and activated

Clock (hours and minutes)

Indicate that the air conditioner is operating in Clean modeDisplayed in Sleep Mode OperationDisplay in ionizer & E.S.F mode operationIndicate that the air conditioner is operating in Economy modeSet temperature or room temperatureDisplayed when the temperature is the room temperatureIndicate that the air conditioner is operating in I FEEL modeAutomatic horizontal air flow oscillation switched onAutomatic supply air flap oscillation switched on

Fan speed indicationSilent speed Low speed

High speed Strong speed

Medium speed

Automatic fan speed

ON/OFF OPERATION BUTTONThis button turns the air conditioner ON and OFF.

MODE SELECTOR BUTTONPress this button to modify the air conditioner mode. (automatic)When this setting is selected, the air conditioner calculates thedifference between the thermostat setting and the room temperature and automatically switches to the "cool" or "heat" mode. (heating)The air conditioner makes the room warmer. dehumidification (dry)The air conditioner reduces the humidity in the room. (cooling)The air conditioner makes the room cooler. (fan)The air conditioner circulate the air.

COOL / DRY / HEAT / FAN Models

SLEEP/ECO BUTTON

1

Description of Low battery detection• The low-battery indicator on the remote control will continue to blink when the batteries are low, it may reduce the transmission distance of the remote control and the display becomes blurred. Replace with new batteries immediately.• The low-battery indicator will disappear after the batteries are replaced.

This button has 2 functions: Sleep function (short press — press it less than 3 seconds). When you short press this button, the mark will appear on the display.

Economy function (long press — press it over 3 seconds). When you long press this button, the mark will appear on the display.For detail see “SLEEP MODE” and “ECONOMY FUNCTION OPERATION”.

I FEEL TEMPERATURE SENSING AND ROOM TEMPERATURE DISPLAY BUTTON

TRANSMITTERWhen you press the buttons of the remote control unit, the mark appears on the display to transmit the setting changes to the receiver in the air conditioner.

SENSOR

TIMER AND PRESENT TIME SETTING BUTTONS

SET BUTTONPush this button to select the functions:

set the present time set the ON-OFF timerFor detail see "HOW TO SET THE PRESENT TIME" and "SETTING THE TIMER".

TIMER BUTTON (timer setting)

TEMPERATURE SETTING BUTTONS- (cooler) Press this button to decrease the set temperature.+ (warmer) Press this button to increase the set temperature.

FAN SPEED SELECTOR BUTTON

Silent speed. Low speed.

High speed. Strong speed.

Fan speed is automatically selected by the microcomputer

LOCKING THE REMOTE CONTROL

VERTICAL SWING BUTTONPush button to activate the supply air flap to auto swing.

TIMER RESET

ION(OPTIONAL)/CLEAN BUTTON

Push the CLEAR button to cancel all timer setting.

2

Medium speed.

Push this button to activate the temperature control in the remote control unit and show the actual room temperature around the remote control.

A temperature sensor inside the remote control unit detects the room temperature.

This button has 2 functions:Ionizer function (short press — press and release it within 3 seconds). When

you short press this button, the mark will appear on the display.Clean function (long press — press it over 3 seconds). When you long press

this button, the mark will disappear after flash five seconds.For detail see “IONIZER FUNCTION OPERATION (OPTIONAL)” and “CLEAN FUNCTION OPERATION”.

Pushing + or - buttons the setting of the time and timer can be activated. For detail see "HOW TO SET THE PRESENT TIME"and "SETTING THE TIMER".

Push theTIMER on the display starts the timer ON and OFF setting procedure. For detail see "SETTING THE TIMER".

Pushing this button freezes the last operation setting.When is activated the remote control will not be able to control the air conditioner.To release the lock status push again.

HORIZONTAL SWING/VERTICAL MANUAL SWING BUTTONPress this button, the remote control will run one of the following functions:

Horizontal auto swing. If the air-condition has horizontal swing motor, push the button will activate the horizontal air flow to auto swing.

Vertical manual swing. If the air-condition only has vertical swing motor, push the button will change the position of vertical air flap by manual.For detail see “ADJUST THE AIR FLOW DIRECTION”.

TEMPERATURE SENSOR SELECTORUnder normal conditions the room temperatureis detected and checked by the temperaturesensor placed in the air conditioner.Press the remote control I FEEL button toactivate the temperature sensor placed inthe remote control. This function is designedto provide a personalised environment bytransmitting the temperature control commandfrom the location next to you. Therefore, inusing this function, the remote control shouldalways be aimed, without obstruction, at the airconditioner.

OPERATION WITH THE REMOTE CONTROL UNIT

Check that the circuit breaker on the powerpanel is turned ON and the STANDBY lamp islight up.When using the remote control unit, alwayspoint the unit transmitter head directly at the airconditioner receiver.

HOW TO TURN ON THE AIR CONDITIONER

Press the ON/OFF button to turn the air conditioner on. The indicator OPERATION will light up, indicating the unit is in operation.

NOTEThe remote control unit sends the temperature signal to the air-condition per four minutes, If the remote control unit stops for more than five minutes due to some troubles, the air conditioner will switch to the

temperature sensor which is built into the indoor unit and controls the room temperature. In these cases, the temperature around the remote control unit may differ from the temperature detected in the air conditioner position. REMOTE CONTROL

UNIT DISPLAY

USING THE REMOTE CONTROL UNITUSING THE REMOTE CONTROL UNIT

HOW TO INSTALL BATTERIESRemove the lid in the rear part of the remote control unit.Insert two AAA alkaline batteries of 1,5 V-DC.Make sure to insert the batteries according to the polarity(+/-) marked in the battery compartment.Push the lid back on.

Remove the lid in the rear part.Press the battery toward the negative end and lift it out by its positive end as shown.

General Note:

Remove the other battery in the same way.

HOW TO REMOVE BATTERIES

Replace the batteries when the remote control unit lamp fails to light, or when the air conditioner does not receive the remote control unit signals.Remove the batteries if you do not use the remote control unit for more than one month.The batteries last about six months, depending on how much you use the remote control unit.The batteries of the remote control contain polluted substances exhausted batteries must be disposed according to the laws in force.

After batteries change:Press the +, -, SET and CLEAR buttons together.( After batteries change the remote control needs to be reset to ensure proper functioning. By pressing above mentioned buttons, remote control programs are reset.)The button + , - refered to above is the buttons for setting the hour not temperature.

3

OPERATIONOPERATION

HOW TO SET THE PRESENT TIME

1. Press the SET button for three seconds. The time indication alone flashes.

2. Press the + or - buttons until the present time is displayed.

3. Press the SET button to stop the indication flashing.

COOLINGVeri fy that the uni t is connected to the main power and the STANDBY lamp is light up.1. Set the MODE selector

to COOL .2. P ress the ON/OFF

button and switch the airconditioner ON.

3.

THE DISPLAY SHOWS THESELECTED TEMPERATURE.

4. Press the FAN SPEED button to select the fan speed.

5.

HEATING 1. Set the MODE selector to HEAT .2. Press the ON/OFF button and switch the air

condioner ON.3.

THE DISPLAY SHOWS THESELECTED TEMPERATURE.

4. Press the FAN SPEED button to select the fan speed.

5.

NOTEFor several minutes after the start of heating operation, the indoor fan will not run until the indoor heat exchanger coil has warmed up sufficiently. This is because the COLD DRAFT PREVENTION SYSTEM is operating.

When the outdoor temperature is low, frost or ice may appear on the heat exchanger coil, reducing the heating performance. When this happens, a microcomputer defrosting system operates. At the same time, the fan in the indoor unit stops and the OPERATION lamp is flashing until defrosting is completed. Heating operation restarts after several minutes. (This interval will vary slightly depending on the room and outdoor temperature).

DEFROSTING OF HEAT EXCHANGE OUTDOOR UNIT “STANDBY”

HEATING PERFORMANCE

A heat pump conditioner heats a room by taking heat from outside air. The heating efficiency will fall off when the outdoor temperature is very low. If enough heat is not obtained with this air conditioner, use another heating appliance in conjunction with it.

4

Press button and button can adjust the air flow direction. For detail see “ADJUST THE AIR FLOW DIRECTION”.

Press button and button can adjust the air flow direction. For detail see “ADJUST THE AIR FLOW DIRECTION”.

Press the TEMP buttons to set the desired temperature (the temperature range is between 30°C (or 26°C) max. and 16°C (or 12°C) min.).Note: The temperature range has 2 options: 16°C -30°C or 12°C -26°C.

Press the TEMP buttons to set the desired temperature (the temperature range is between 30°C (or 26°C) max. and 16°C (or 12°C) min.).Note: The temperature range has 2 options: 16°C -30°C or 12°C -26°C.

AUTOMATIC OPERATION

1. Set the MODE selector to AUTO .2. Press the ON/OFF button and switch the air

condioner ON.3. Press the TEMP. buttons to set the desired

temperature (The temperature range is

THE DISPLAY SHOWS THESELECTED TEMPERATURE.

When th is set t ing is se lected, the a i r cond i t ioner ca lcu la tes the d i f fe rence between the thermostat setting and the room temperature and automatically switches to the COOL or HEAT mode as appropriate.

4. Switch the FAN SPEED selector button to the setting you want.Example of operation diagram in the (Auto) mode with the set room temperature at 23°C.

NOTEThe air conditioner changes the operation mode (from cool to heat), if one of the following conditions occurs:- ZONE A: changes if the difference between the room temperature and the temperature set on the remote control unit is at least 3°C..- ZONE B: changes if the difference between the room temperature and the temperature set on the remote control unit is at least 1°C,one hour after the compressor stop.- ZONE C: never changes if the difference between the room temperature and the temperature set on the remote control unit isno more than 1°C.

DEHUMIDIFYING (DRY)

1. Set the MODE selector switch to “DRY” .2. Press the ON/OFF button and switch the air

condioner ON.3. Press the TEMP. buttons to set the desired

temperature (The temperature range is

THE DISPLAY SHOWS THESELECTED TEMPERATURE.

NOTEUse DRY operation when you want to reduce the humidity in the room.Once the room temperature reaches the set level, the unit repeats the cycle of turning on and off automatically.During DRY operation, the fan speed is automatically set to low or stops to prevent overcooling.Dry operation is not possible if the indoor temperature is 15 °C or less.

FAN ONLY

If you want to make air circulate without any temperature control, follow these steps:

1. Set the MODE selector switch to “FAN” .2. Press the ON/OFF button and switch the air

conditioner ON.

OPERATIONOPERATION

5

between 30℃(or 26℃) max. and 16℃(or 12℃)Note: the temperature range has 2 options: 16℃-30℃ or 12℃-26℃

between 30℃(or 26℃) max. and 16℃(or 12℃)Note: the temperature range has 2 options: 16℃-30℃ or 12℃-26℃

OPERATIONOPERATION

ADJUSTING THE FAN SPEED

AUTOMATIC

Simply set the FAN SPEED selector to the position . A microcomputer automatically controls the fan speed when the AUTO mode is selected. When the air conditioner starts operating, the difference between the room temperature and the set temperature is detected by the microcomputer which then automatically switches the fan speed to the most suitable level.

NOTEIn FAN Only mode the fan speed is adjusted automatically as in cooling mode.

WHEN DIFFERENCE BETWEENROOM TEMPERATURE AND SET

TEMPERATURE ISFAN SPEED

Cooling anddehumidifyingmodes:

2 °C and over HighBetween 2 and 1 °C Medium

Below 1 °C Low

Heating mode:2 °C and over High

Below 2 °C Medium

The above mentioned data make reference to the conditioner operating when the sensor on the remote control unit is ON. If the sensor on the indoor unit is being used then actual operation will slightly differ from that described in the above tables.

MANUAL

If you want to manually adjust speed just set the FAN SPEED selector as desired.

Each time the button is pressed, the fan speed is changed in sequence:

SLEEP MODE

The SLEEP mode enables you to save energy.1. Set the MODE selector to cool, dry or heat.

What does the SLEEP mode mean?

In this mode, the air conditioner will cool or heat the room to the set temperature, and then the thermostat will make the unit pause. After about 1 hour, the air conditioner will automatically reset the set temperature as follows (also refer to graphs).

OPERATING MODE SET TEMPERATURE CHANGEHeating Lowered by 1 °C

Cooling and Dehumidifying Raised by 1 °C

When the room temperature reaches the new set value, the thermostat will cause the unit to pause. After about 1 hour the temperature will be raised by 1 °C in cooling, or lowered by 1 °C in heating. This enables you to save energy without sacrificing your comfort.

Setting temperature Room temperature

Setting temperature Room temperature

COOLING AND DEHUMIDIFYING

1 hour 1 hour TIME

1 hour 1 hour TIME

HEATING

6

(Silent) (Low)

(High)

(Medium)

(Strong) (Auto)

1) Strong fan will only operation cooling & heating mode.2) Silent fan and Strong fan are both optional, and they depends on the air-condition type.

2. Short press the SLEEP/ECO button (release it within three seconds).3. The mark appears on the display. Short press the SLEEP/ECO button again to release the SLEEP function.

OPERATIONOPERATION

I FEEL/ROOM TEMP FUNCTION OPERATION

Press button I FEEL/ROOM to activate the I FEEL function. Thermometer sign will appear on the LCD operation display . Select suitable temperature setting. Make sure that the remote control unit is aimed at the air conditioner, with the I FEEL sensor in front. Prevent the I FEEL sensor from being affected by heat sources such as lamps, heaters, direct sun, etc. or from being directly affected by the air conditioner air flow. These may cause the sensor to transmit the wrong temperature data, thereby disturbing the performance of the I FEEL function. By pressing on ROOM temperature, the measured room temperature sign will be displayed .To cancel the ROOM Temperature display press on one of the following:

Press again on ROOM Temperature button.Change of MODE button.

NOTERoom temperature range is between 0 and 50 in 1 increments. Display should show "HI" or "LO" to represent temperature that is above 50 or below 0.

LOCK FUNCTION

By pressing LOCK button, the remote control will lock the last operation program. All the function buttons will be inoperative, including START/STOP button. By pressing LOCK button again the remote control will be released from its locked position. When lock mode is functioning, the transmission sign will be on.

SETTING THE TIMER

There are two daily timers that can be selected on the remote control. Each timer can beselected by pressing TIMER button.The daily timers T1 and T2 can be set for ON and OFF separately for two different time periods.Timer setting will not change until new setting is input.

A) HOW TO SET THE ON TIME

1. Press the TIMER button to select the desired timer.

2. Press the SET button till the ON sign blinks.

3. Press the + or - (HOUR) button until the desired value is displayed.

4. Press the SET button to activate the timer.

B) HOW TO SET THE OFF TIME

1. Press the TIMER button to select the desired timer.

2. Press the SET buttons till the OFF sign blinks.

7

Short press ION/CLEAN button (release it within three seconds), the mark appears on the display. Short press the button again to release the IONIZER function (E.S.F works together with Ionizer).

IONIZER FUNCTION OPERATION (OPTIONAL)

OPERATIONOPERATION

C) HOW TO SET A PROGRAM FOR DAILY ON/OFF OPERATION

1. Press the TIMER button to select the desired timer.

2. Press the SET button till the ON sign blinks.3. Press the + or - (HOUR) button until the

desired value is displayed.4. Press the SET button again, the OFF sign

blinks.5. Press the + or - (HOUR) button until the

desired value is displayed.6. Press the SET button to activate the timer.

D) HOW TO CLEAR THE TIMER1. Press the TIMER button to select the timer.2. Press the CLEAR button if you want that every

timer operation will be cleared.

Set vertical vanes to the front position during COOLING/DRY operation if humidity is high.If the vertical vanes are set to the left-most or right-most position, condensation will form around the air outlet and drip off.

NOTEIf the procedure to set the timer is not completed, by pushing the SET button, within 15 seconds the timer operation will be cancelled and the last set-up is restored.

Do not move the flap with your hands when the air conditioner is running.

NOTESThe flap automatically closes when the unit is off.During the heating operation, the fan speed will be very low and the flap will be in the horizontal position until the air being blown out of the unit begins to warm. Once the air warms up, the flap position and fan speed change to the settings specified with the remote control.

Use the FLAP button on the remote control to adjust the position of the flap. If you move the flap by hand, the factual flap position and the flap position on the remote control may no longer match. If this should happen, shut off the unit, wait for the flap to close, and then turn on the unit again; the flap position will now be normal again.Do not have the flap pointed down during cooling operation. Condensation may begin to form around the air vent and drip down.

3. Press the + or - (HOUR) button until the desired value is displayed.

4. Press the SET button to activate the timer.

ADJUSTING THE AIR FLOW DIRECTION

Press button to activate the supply air flap to auto swing. If you push again the flap stops immediately.

8

Press button has two options:If the indoor unit has a horizontal motor, press the button to activate the horizontal air flow auto swing, and press it again, the flap stops immediately.If the indoor unit has not horizontal motor, press the button to stop the vertical air flow auto swing, and the position of vertical air flap will be changed by manual.

OPERATIONOPERATION

9

Some functions of remote controller will not be available when the unit does not support them!

NOTES

The CLEAN function comes to dry the indoor coil as well as mould prevention.Long press the ION/CLEAN button (release it after three seconds), the mark will disappear after flash five seconds and notice the indoor unit execute CLEAN function.

CLEAN FUNCTION OPERATION

The function comes to reduce energy of the unit operation by limiting the maximum allowed power input 1. Long press the SLEEP/ECO button (release it after three seconds).2. The mark appears on the display. Long press the SLEEP/ECO button again, to release the ECONOMY function.

ECONOMY FUNCTION OPERATION