Remote Control Keys V2.4 Last updated: 2014-03-18

1

Product: Page Model 3 A20 / I20 / I21 4 A30.1 / I30 5 D20 / D30.2 6 PRE30 7 T21 / T22 / T30 8 SP31.7 / SPA20 9 SP31 / SPA21 10 V10, V20, V25 11 DVD30 13 P30 14 DVD26 16 CD21 /CD31 17 Master Delay Box 18 T23 20 CDI10 22 DVDI10 24 SPA22/SP32 26 CD32 27 I32 28 PRE32 29 NP30 30 DAC30 31 BD32 33 History

2

A20 / I20 / I21 Remote Control Commands. RC5 address = 20 (0x14) Bits: 0x0500 = 0000 0101 0000 0000 (=1280) xxxx tsss ssdd dddd (s ssss = 1 0100 = 0x14 = 20) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands Key Dec. Value Hex. Value Action standby 12 (0x0c) Standby ON (common) standby 1 (0x01) Standby ON (unique) operate 2 (0x02) Operate (Standby OFF) step up 30 (0x1e) Next input step down 31 (0x1f) Previous input input mode 26 (0x1a) Toggle input mode (balance, master volume) mute 49 (0x31) Toggle mute on/off plus 16 (0x10) Increase/change master volume and balance minus 17 (0x11) Decrease/change master volume and balance dim 10 (0x0a) Toggle display on/off 1 60 (0x3c) Used for main input selection 2 61 (0x3d) Used for main input selection 3 62 (0x3e) Used for main input selection 4 63 (0x3f) Used for main input selection For complete command, just add system address value 1280 with key value 1 (for standby) = 1281 (0x0501).

3

A30.1 / I30 Remote Control Commands. RC5 address = 20 (0x14) bits: 0x0500 = 0000 0101 0000 0000 (=1280) xxxx tsss ssdd dddd (s ssss = 1 0100 = 0x14 = 20) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands Note !. Commands in Red Require Firmware update for use on A30.1 and some I30. Key Dec. Value Hex. Value Action standby 12 (0x0c) Standby ON (common) (with d20/d30)) standby 1 (0x01) Standby ON (unique) operate 2 (0x02) Operate (Standby OFF) step up 30 (0x1e) Next input step down 31 (0x1f) Previous input input mode 26 (0x1a) Toggle input mode (balance, master volume) mute 49 (0x31) Toggle mute on/off plus 16 (0x10) Increase/change master volume and balance minus 17 (0x11) Decrease/change master volume and balance dim 10 (0x0a) Toggle display on/off 1 60 (0x3c) Used for main input selection 2 61 (0x3d) Used for main input selection 3 62 (0x3e) Used for main input selection 4 63 (0x3f) Used for main input selection 5 3 (0x03) Used for main input selection 6 4 (0x04) Used for main input selection For complete command, just add system address value 1280 with key value 12 (for standby) = 1292 (0x050c).

4

D20/D30.2 Remote Control Commands. RC5 address = 20 (0x14) bits: 0x0500 = 0000 0101 0000 0000 (=1280) xxxx tsss ssdd dddd (s ssss = 1 0100 = 0x14 = 20) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands Key Dec. Value Hex. Value Action Open 45 (0x2d) play 53 (0x35) play/pause stop 54 (0x26) standby 12 (0x0c) long press = Standby ON, any other key = Operate operate 58 (0x3a) dim 10 (0x0a) next_track 32 (0x20) ff 52 (0x34) prev_track 33 (0x21) rew 50 (0x32) plus10 47 (0x2f) time 11 (0x0b) a_b 59 (0x3b) repeat 29 (0x1d) mem 41 (0x29) 1 13 (0x0d) 2 14 (0x0e) 3 15 (0x0f) 4 18 (0x12) 5 19 (0x13) 6 20 (0x14) 7 21 (0x15) 8 22 (0x16) 9 23 (0x17) 0 24 (0x18) check 25 (0x19) clear 27 (0x1b) shuffle 28 (0x1c) intro 34 (0x22) auto_space 35 (0x23) play2 36 (0x24) only play pause 37 (0x25) only pause For complete command, just add system address value 1792 with key value 50 (for standby) = 1842 (0x0732).

5

Pre30 Remote Control Commands. RC5 address = 24 (0x18) bits: 0x0600 = 0000 0110 0000 0000 (=1536) xxxx tsss ssdd dddd (s ssss = 1 1000 = 0x18 = 24) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands Key Dec. Value Hex. Value Action standby 50 (0x32) Standby ON step up 30 (0x1e) Next input (surround/record/main) step down 31 (0x1f) Previous input (surround/record/main) input level 38 (0x26) toggle input mode (input level/master volume) balance 26 (0x1a) toggle input mode (balance, master volume) mute 49 (0x31) Toggle mute on/off plus 16 (0x10) Increase/change master volume, balance, input level minus 17 (0x11) Decrease/change master volume, balance, input level dim 10 (0x0a) Toggle display on/off mode 42 (0x2a) Toggle surround mode on/off record 48 (0x30) Toggle input mode record input path/main input path operate 58 (0x3a) Operate (Standby OFF) select 43 (0x2b) Reserved 1 13 (0x0d) Used for main input selection 2 14 (0x0e) Used for main input selection 3 15 (0x0f) Used for main input selection 4 18 (0x12) Used for main input selection 5 19 (0x13) Used for main input selection 6 20 (0x14) Used for main input selection 7 21 (0x15) Used for main input selection 8 22 (0x16) Used for main input selection 9 23 (0x17) Used for main input selection 0 24 (0x18) Used for main input selection 10 47 (0x2f) Used for main input selection For complete command, just add system address value 1536 with key value 50 (for standby) = 1586 (0x0632).

6

T21 / T22 / T30 Remote Control Commands. RC5 address = 16 (0x10) bits: 0x0400 = 0000 0100 0000 0000 (=1024) xxxx tsss ssdd dddd (s ssss = 1 0000 = 0x10 = 16) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands Key Dec. Value Hex. Value Action operate 1 (0x01) Operate (Standby OFF / STANDBY ON?) display 2 (0x02) preset/tune 3 (0x03) antenna 4 (0x04) blend 5 (0x05) if 6 (0x06) mono 7 (0x07) scan up 8 (0x08) scan down 9 (0x09) preset 1 10 (0x0a) preset 2 11 (0x0b) preset 3 12 (0x0c) preset 4 13 (0x0d) preset 5 14 (0x0e) preset 6 15 (0x0f) preset 7 16 (0x10) preset 8 17 (0x11) preset 9 18 (0x12) store 19 (0x13) preset up 20 (0x14) preset down 21 (0x15) dim 22 (0x16) For complete command, just add system address value 1024 with key value 1 (for operate) = 1025 (0x0401).

7

SP31.7 / SPA20 Remote Control Commands. RC5 address = 28 (0x1c) bits: 0x0700 = 0000 0111 0000 0000 (=1792) xxxx tsss ssdd dddd (s ssss = 1 1100 = 0x1c = 28) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands Key Dec. Value Hex. Value Action standby 50 (0x32) long press = Standby ON operate 58 (0x3a) Operate (Standby OFF) step up 16 (0x10) In menus: previous row

Other: Next input step down 17 (0x11) In menus: next row

Other: Previous input input mode 26 (0x1a) toggle input mode (balance, center, side, rear, sub, master) mute 49 (0x31) Toggle mute on/off plus 30 (0x1e) In menus: menucommand "next"

Other: Increase/change master volume, balance, center, side, rear, sub

minus 31 (0x1f) In menus: menucommand "previous" Other: Decrease/change master volume, balance, center, side, rear, sub

dim 10 (0x0a) Toggle display on/off menu 38 (0x26) In menus: short press = previous menu

long press = leave menus Other: Enter menus

mode 42 (0x2a) Next surround mode for 2ch inputs select 43 (0x2b) In menus: menucommand "next" record 48 (0x30) Next input for record path

(This command does not exist on SPA20) 1 13 (0x0d) Used for main input selection 2 14 (0x0e) Used for main input selection 3 15 (0x0f) Used for main input selection 4 18 (0x12) Used for main input selection 5 19 (0x13) Used for main input selection 6 20 (0x14) Used for main input selection 7 21 (0x15) Used for main input selection 8 22 (0x16) Used for main input selection 9 23 (0x17) Used for main input selection 0 24 (0x18) Used for main input selection 10 47 (0x2f) Used for main input selection For complete command, just add system address value 1792 with key value 50 (for standby) = 1842 (0x0732).

8

SP31 / SPA21 Remote Control commands. RC5 address = 28 (0x1c) bits: 0x0700 = 0000 0111 0000 0000 (=1792) xxxx tsss ssdd dddd (s ssss = 1 1100 = 0x1c = 28) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands Key Dec. Value Hex Value Action standby 50 (0x32) Toggle Standby/Operate operate 58 (0x3a) Operate (Standby OFF) standby 59 (0x3b) Standby (Standby ON) step up 16 (0x10) In menus: previous row

Other: Next input step down 17 (0x11) In menus: next row

Other: Previous input input mode 26 (0x1a) toggle input mode (balance, center, side, rear, sub, master) mute 49 (0x31) Toggle mute on/off plus 30 (0x1e) In menus: menucommand "next"

Other: Increase/change master volume, balance, center, side, rear, sub

minus 31 (0x1f) In menus: menucommand "previous" Other: Decrease/change master volume, balance, center, side, rear, sub

dim 10 (0x0a) Toggle display on/off menu 38 (0x26) In menus: short press = previous menu

long press = leave menus Other: Enter menus

mode 42 (0x2a) Next surround mode for 2ch inputs select 43 (0x2b) In menus: menucommand "next" record 48 (0x30) Next input for record path

(This command does not exist on SPA21) 1 13 (0x0d) Used for main input selection 2 14 (0x0e) Used for main input selection 3 15 (0x0f) Used for main input selection 4 18 (0x12) Used for main input selection 5 19 (0x13) Used for main input selection 6 20 (0x14) Used for main input selection 7 21 (0x15) Used for main input selection 8 22 (0x16) Used for main input selection 9 23 (0x17) Used for main input selection 0 24 (0x18) Used for main input selection 10 47 (0x2f) Used for main input selection For complete command, just add system address value 1792 with key value 50 (for standby) = 1842 (0x0732).

9

V10 / V20 / V25 Remote Control commands. NEC system (32 bits) SYSTEM CODE: 00FEH Key Dec. Value Hex. Value Action Open 65 0x41 Power 93 0x5D Mute 73 0x49 Goto 77 0x4D Menu 85 0x55 Title 88 0x58 1 64 0x40 2 68 0x44 3 80 0x50 Audio 92 0x5C 4 72 0x48 5 76 0x4C 6 84 0x54 Angle 27 0x1B 7 3 0x03 8 7 0x07 9 19 0x13 Subtitle 31 0x1F 0 15 0x0F Subtitle_On 26 0x1A Setp 2 0x02 Repeat 18 0x12 Repeat_AB 30 0x1E Slow- 10 0x0A Slow+: 14 0x0E Program 22 0x16 Clear 28 0x1C Display 0 0x00 Zoom 4 0x04 Setup 16 0x10 Return 24 0x18 Play 8 0x08 Stop 20 0x14 Up 5 0x05 Down 13 0x0D Left 1 0x01 Right 25 0x19 Rew 69 0x45 Ff 9 0x09 Prev 21 0x15 Next 29 0x1D Power_Off (unique): 11 0x0B (Note! only for V25 with newer software) Power_On (unique): 23 0x17 (Note! only for V25 with newer software) Dimmer 89 0x59 Select 17 0x11

10

DVD30 Remote Control Keys Remote Control commands. RC5 address = 12 (0x0c) bits: 0x0300 = 0000 0011 0000 0000 (=768) xxxx tsss ssdd dddd (s ssss = 0 1100 = 0x0c = 12) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands

Key Dec. Value Hex. Value Action STOP 0 0x00

FF 1 0x01

REW 2 0x02

SKIP+ 3 0x03

SKIP- 4 0x04

PLAY 5 0x05

PAUSE 6 0x06

OPEN/CLOSE 7 0x07

POWER ON/OFF 8 0x08

JOG FWD 0 9 0x09

JOG FWD 1 10 0x0A

JOG FWD 2 11 0x0B

JOG FWD 3 12 0x0C

JOG REV 0 13 0x0D

JOG REV 1 14 0x0E

JOG REV 2 15 0x0F

JOG REV 3 16 0x10

VNR (picture adjust) 17 0x11

POWER ON 18 0x12

POWER OFF 19 0x13

SUBTITLE 23 0x17

CURSOR LEFT 24 0x18

CURSOR RIGHT 25 0x19

CURSOR UP 26 0x1A

CURSOR DOWN 27 0x1B

FUNCTION MEMORY 28 0x1C

CONDITION MEMORY 29 0x1D

LAST MEMORY 30 0x1E

MULTISPEED FWD 1 31 0x1F

MULTISPEED FWD 2 32 0x20

11

MULTISPEED REV 1 33 0x21

MULTISPEED REV 2 34 0x22

STEP/SLOW FWD 35 0x23

STEP/SLOW REV 36 0x24

0 37 0x25

1 38 0x26

2 39 0x27

3 40 0x28

4 41 0x29

5 42 0x2A

6 43 0x2B

7 44 0x2C

8 45 0x2D

9 46 0x2E

+10 47 0x2F

SETUP 48 0x30

MENU 49 0x31

TOPMENU 50 0x32

DISPLAY (osd) 51 0x33

SEARCHMODE 52 0x34

ANGLE 53 0x35

AUDIO 54 0x36

REPEAT 55 0x37

REPEAT A-B 56 0x38

RANDOM 57 0x39

CLEAR 58 0x3A

PROGRAM 59 0x3B

ENTER 60 0x3C

RETURN 61 0x3D

DIMMER 62 0x3E

PLAY/PAUSE 63 0x3F

12

P30 Remote Control commands. RC5 address = 20 (0x14) bits: 0x0500 = 0000 0101 0000 0000 (=1280) xxxx tsss ssdd dddd (s ssss = 1 0100 = 0x14 = 20) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) Key Dec. Value Hex. Value Action standby 39 (0x27) Standby ON step up 30 (0x1e) In menus: menucommand "next"

Other: Next input step down 31 (0x1f) In menus: menucommand "previous"

Other: Previous input input mode 26 (0x1a) In menus: short press = previous menu

long press = leave menus short press = toggle input mode (balance, center, rear, sub, master) Other long press = enter menus

mute 12 (0x0c) Toggle mute on/off plus 16 (0x10) In menus: previous row

Other: Increase/change master volume, balance, center, rear, sub

minus 17 (0x11) In menus: next row Other: Decrease/change master volume, balance, center, rear, sub

dim 10 (0x0a) Toggle display on/off menu 38 (0x26) Enter/leave menus For complete command, just add system address value 1280 with key value 39 (for standby) = 1319 (0x0527).

13

DVD26 Remote Control Keys Remote Control commands. RC5 address = 12 (0x0c) bits: 0x0300 = 0000 0011 0000 0000 (=768) xxxx tsss ssdd dddd (s ssss = 0 1100 = 0x0c = 12) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands

Key Dec. Value Hex. Value Action STOP 0 0x00 FF 1 0x01 REW 2 0x02 SKIP+ 3 0x03 SKIP- 4 0x04 PLAY 5 0x05 PAUSE 6 0x06 OPEN/CLOSE 7 0x07 POWER ON/OFF TOGGLE 8 0x08 POWER ON 18 0x12 POWER OFF 19 0x13 SUBTITLE 23 0x17 CURSOR LEFT 24 0x18 CURSOR RIGHT 25 0x19 CURSOR UP 26 0x1A CURSOR DOWN 27 0x1B RESUME ON/OFF 29 0x1D SLOW FWD 1 31 0x1F FRAME FWD 2 32 0x20 SLOW REW 1 33 0x21 FRAME REW 2 34 0x22 0 37 0x25 1 38 0x26 2 39 0x27 3 40 0x28 4 41 0x29 5 42 0x2A 6 43 0x2B 7 44 0x2C 8 45 0x2D

14

9 46 0x2E +10 47 0x2F SETUP 48 0x30 TITLE MENU 49 0x31 TOPMENU 50 0x32 DISPLAY (osd) 51 0x33 SEARCHMODE (goto) 52 0x34 ANGLE 53 0x35 AUDIO 54 0x36 REPEAT 55 0x37 REPEAT A-B 56 0x38 RANDOM 57 0x39 CLEAR 58 0x3A PROGRAM 59 0x3B ENTER 60 0x3C RETURN 61 0x3D DIMMER 62 0x3E PLAY/PAUSE TOGGLE 63 0x3F

15

CD21 / CD31 Remote Control Commands. RC5 address = 20 (0x14) bits: 0x0500 = 0000 0101 0000 0000 (=1280) xxxx tsss ssdd dddd (s ssss = 1 0100 = 0x14 = 20) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands Key Dec. Value Hex. Value Action Open 45 (0x2d) Play/Pause (Toggle) 53 (0x35) stop 54 (0x26) standby (Toggle) 12 (0x0c) standby (Unique) 57 (0x39) operate (Unique) 58 (0x3a) dim 10 (0x0a) next_track 32 (0x20) ff 52 (0x34) prev_track 33 (0x21) rew 50 (0x32) plus10 47 (0x2f) time 11 (0x0b) a_b 59 (0x3b) repeat 29 (0x1d) Mem 41 (0x29) 1 13 (0x0d) 2 14 (0x0e) 3 15 (0x0f) 4 18 (0x12) 5 19 (0x13) 6 20 (0x14) 7 21 (0x15) 8 22 (0x16) 9 23 (0x17) 0 24 (0x18) shuffle 28 (0x1c) intro 34 (0x22) play2 (only Play) 36 (0x24) pause (only Pause) 37 (0x25) For complete command, just add system address value 1792 with key value 50 (for standby) = 1842 (0x0732).

16

Delay Box Remote Control commands. RC5 address = 8 (0x08) bits: 0x0200 = 0000 0010 0000 0000 (=256) xxxx tsss ssdd dddd (s ssss = 1 000 = 0x08 = 8) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands Key Dec. Value Hex. Value Action Standby 1 (0x01) Standby ON Operate 2 (0x02) Standby Off Standby 12 (0x0c) Toggle Standby/Operate Up 3 (0x03) Increasing delay time Down 4 (0x04) Decreasing delay time Input 1 5 (0x05) Used for main input selection. Input 2 6 (0x06) Used for mail input selection Preset 1 7 (0x07) Delaytime memory 1 Preset 2 8 (0x08) Delaytime memory 2 Bypass 9 (0x09) Enable bypass mode. Dim 10 (0x0A) Toggle DIM Mode For complete command, just add system address value 0512 with key value 1 (for operate) = 0513 (0x0201).

17

T23 Remote Control Commands. RC5 address = 16 (0x10) bits: 0x0800 = 0000 1000 0000 0000 (=2048) xxxx tsss ssdd dddd (s ssss = 1 0000 = 0x10 = 16) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands Due to compability reasons command , 4, 5, 6 should not be used. Key Dec. Value Hex. Value Action Operate / Standby 1 (0x01) (Toggle) Display 2 (0x02) (Shifts between RDS info) Mono / Auto 3 (0x07) toggle (in DAB-mode, enter menu) FM Manual Tune UP DAB service +, menu +

8 (0x08) (long press search up)

FM Manual Tune Down DAB service -, menu -

9 (0x09) (long press search down)

Preset 1 (direct) 10 (0x0a) Preset 2 (direct) 11 (0x0b) Preset 3 (direct) 12 (0x0c) Preset 4 (direct) 13 (0x0d) Preset 5 (direct) 14 (0x0e) Preset 6 (direct) 15 (0x0f) Preset 7 (direct) 16 (0x10) Preset 8 (direct) 17 (0x11) Preset 9 (direct) 18 (0x12) Preset 0 24 (0x18) Store (mem) 19 (0x13) Preset +10 23 (0x17) Clear 29 (0x1D) Preset UP (DAB/FM) 20 (0x14) Preset Down (DAB/FM) 21 (0x15) Dim toggle 22 (0x16) (toggle between DIM-modes) Standby Mode Off (unique) 25 (0x19) Standby mode On (unique) 26 (0x1A) FM Search up 27 (0x1B) FM Search down 28 (0x1C) Select 30 (0x1E) Auto, default 31 (0x1F) (in FM, enable auto-shift

stereo/mono), (unique) Mono 32 (0x20) (in FM, enable mono mode), (unique)

18

Toggle DAB / FM mode 33 (0x21) DAB mode (unique) 34 (0x22) FM mode (unique) 35 (0x23) For complete command, just add system address value 1024 with key value 1 (for operate) = 1025 (0x0401).

19

Cdi10 Remote Control Keys RC5 address = 14 (0x0e) bits: 0x0380 = 0000 0011 1000 0000 (=896) xxxx tsss ssdd dddd (s ssss = 0 1110 = 0x0e = 14) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands Key Dec. Value Hex Value Action Standby 8 0x08 Standby toggle 1 38 0x26 2 39 0x27 3 40 0x28 4 41 0x29 5 42 0x2A 6 43 0x2B 7 44 0x2C 8 45 0x2D 9 46 0x2E Clear 58 0x3A 0 37 0x25 +10 47 0x2F Volume - 29 0x1D Arrow up 26 0x1A Volume + 30 0x1E Arrow Left 24 0x18 In FM Tune Down Select 60 0x3C Arrow Right 25 0x19 In FM Tune UP stop 0 0x00 Arrow Down 27 0x1B Play/Pause toggle 63 0x3F DIM 62 0x3E Mode 54 0x36 In FM toggle mono/Auto. In DAB mode toggle tuning alternatives. Display 51 0x33 In FM toggle FM/RDS information. In DAB mode toggle DAB

information / Text. Open 7 0x07 Skip back 4 0x04 In CD skip back, In FM Search Down Mem 23 0x17 Skip Forward 3 0x03 In CD Skip Forward, In FM Search UP REW 2 0x02 Repeat 55 0x37 FF 1 0x01 IN1 17 0x11 Direct input selection

20

IN2 20 0x14 Direct input selection IN3 21 0x15 Direct input selection IN4 (front) 22 0x16 Direct input selection CD 12 0x0C Direct input selection DAB/FM (toggle) 13 0x0D Operate (uniqe) 18 0x12 Standby mode off OFF (unique) 19 0x13 OFF mode on Standby (unique) 16 0x10 Standby mode ON Pause 6 0x06 only pause Play 5 0x05 only play Repeat a-b 56 0x38 Resume on/off 35 0x23 Dab 14 0x0E Direct input selection FM 15 0x0F Direct input selection

21

DVDi10 Remote Control Commands. RC5 address = 18 (0x12) bits: 0x0480 = 0000 0100 1000 0000 (=1152) xxxx tsss ssdd dddd (s ssss = 1 0010 = 0x12 =18) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands

Function Dec. Value Hex Value Action Standby(toggle) 8 0x08

1 38 0x26 2 39 0x27 3 40 0x28 4 41 0x29 5 42 0x2A 6 43 0x2B 7 44 0x2C 8 45 0x2D 9 46 0x2E

Clear 58 0x3A 0 37 0x25

+10 47 0x2F Volume - 29 0x1D Arrow up 26 0x1A Volume + 30 0x1E Arrow Left 24 0x18

Select 60 0x3C Arrow Right 25 0x19 Stop/Open 0 0x00

Arrow Down 27 0x1B Play/Pause (toggle) 63 0x3F

Menu 49 0x31 DIM 62 0x3E

Mode 54 0x36 Display 51 0x33 Setup 48 0x30 Skip - 4 0x04 MEM 59 0x3B Skip + 3 0x03 REW 2 0x02

Repeat 55 0x37 FF 1 0x01

Goto 52 0x34

22

Angle 53 0x35 Topmenu 50 0x32 Subtitle 23 0x17

DVD 12 0x0C FM 15 0x0F

DAB/AM 13 0x0D ipod 16 0x10 IN1 17 0x11 IN2 20 0x14 IN3 21 0x15 IN4 22 0x16

Operate (uniqe) 18 0x12 Standby (unique) 19 0x13

Open 7 0x07 Pause 6 0x06 Play 5 0x05

Repeat a-b 56 0x38 Resume on/off 35 0x23

Slow FWD1 31 0x1F Frame FMD2 32 0x20 Slow REW1 33 0x21

Frame REW2 34 0x22 Return 61 0x3D

Dab 14 0x0E Am 11 0x0B

Random 57 0x39

23

SP32/SPA22 Remote Control Commands RC5 address = 28 (0x1c) bits: 0x0700 = 0000 0111 0000 0000 (=1792) xxxx tsss ssdd dddd (s ssss = 1 1100 = 0x1c = 28) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands IR Dec. Value Hex. Value Description Standby toggle 50 0x32 Toggle standby Standby ON 59 0x3B Standby ON Operate 58 0x3A Standby OFF Step-UP 16 0x10 Next main input / prev row in menus Step Down 17 0x11 Previous main input / next row in menus Input mode (balanced) 26 0x1A Balance / Center / Surr / Surr back / Sub / Master -volume toggle

Mute 49 0x31 Mute On / Off Plus 30 0x1E Volume + Minus 31 0x1F Volume - Dim 10 0x0A DIM On / Off Menu 38 0x26 Menu / Menu-back / Menu exit Mode 42 0x2A Next surround mode for 2ch inputs Select 43 0x2B Menu command + (select) 0 24 0x18 Direct input access 1 13 0x0D Direct input access 2 14 0x0E Direct input access 3 15 0x0F Direct input access 4 18 0x12 Direct input access 5 19 0x13 Direct input access 6 20 0x14 Direct input access 7 21 0x15 Direct input access 8 22 0x16 Direct input access 9 23 0x17 Direct input access +10 47 0x2F Direct input access Zone II Volume + 32 0x20 Increase Zone II volume Zone II Volume - 33 0x21 Decrease Zone II volume Zone II Mute 34 0x22 Mute Zone2 output Zone II input + 48 0x30 Next Zone II input Zone II input - 36 0x24 Prevoius Zone II input Zone II input 1 2 0x02 Zone II input direct Zone II input 2 3 0x03 Zone II input direct

24

Zone II input 3 4 0x04 Zone II input direct Zone II input 4 5 0x05 Zone II input direct Zone II input 5 6 0x06 Zone II input direct Zone II input 6 7 0x07 Zone II input direct Zone II input 7 8 0x08 Zone II input direct Zone II input 8 9 0x09 Zone II input direct Zone II input 9 12 0x0C Zone II input direct Zone II input 0 1 0x01 Zone II input direct Zone II input +10 11 0x0B Zone II input direct

25

CD32 Remote Control Commands RC5 address = 20 (0x14) bits: 0x0500 = 0000 0101 0000 0000 (=1280) xxxx tsss ssdd dddd (s ssss = 1 0100 = 0x14 = 20) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands

IR Dec.

Value Hex Value Description Dimmer 10 0x0A DIM Toggle

Time 11 0x0B Power ON/OFF 12 0x0C Toggle standby

1 13 0x0D 2 14 0x0E 3 15 0x0F 4 18 0x12 5 19 0x13 6 20 0x14 7 21 0x15 8 22 0x16 9 23 0x17 0 24 0x18

Shuffle (toggle) 28 0x1C Enable in play-mode Repeat 29 0x1D Enable in play-mode

Next Track 32 0x20 Previous Track 33 0x21

Sample rate toggle 36 0x24 toggle 44.1, 48, 96 Khz. Play (unique) 5 0x05 Only play

Pause (unique) 37 0x25 Only pause Open / Close toggle 45 0x2D

+10 47 0x2F Rew 50 0x32 FF 52 0x34

Play / Pause Toggle 53 0x35 Enter folder / play in USB Stop 54 0x36

Operate Off 57 0x39 Only standby mode ON Operate ON 58 0x3A Only standby mode Off

Mem 41 0x29 Programming mode Arrow up 40 0x28 Navigation in USB Arrow left 44 0x2C Navigation in USB

Select 46 0x2E Navigation in USB Arrow right 51 0x33 Navigation in USB Arrow down 56 0x38 Navigation in USB Mode/Audio 55 0x37 Toggle between USB/CD

26

I32 Remote Control Commands RC5 address = 20 (0x14) bits: 0x0500 = 0000 0101 0000 0000 (=1280) xxxx tsss ssdd dddd (s ssss = 1 0100 = 0x14 = 20) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands

IR Dec. Value Hex Value Description Toggle standby 12 0x0C Standby on/off toggle

Standby 1 0x01 Only standby Operate 2 0x02 Only Operate Arrow up 30 0x1E input / menu up

Arrow down 31 0x1F input / menu down Select 43 0x2B Menu navigation Return 48 0x30 Menu navigation

Arrow right 8 0x08 Menu navigation Menu 0 0x00 Menu navigation

Arrow left 9 0x09 Menu navigation Balance 26 0x1A Master balance toggle

Mute 49 0x31 Mute toggle Plus / Vol+ 16 0x10 Volume up

Minus / Vol- 17 0x11 Volume down Dim 10 0x0A Toggle dim levels

Menu (Top Level) 65 0x41 Menu navigation Num 1 60 0x3C Select input IN1 Num 2 61 0x3D Select input IN2 Num 3 62 0x3E Select input IN3 Num 4 63 0x3F Select input IN4 Num 5 3 0x03 Select input IN5

Num +10, Num 0 47, 24 0x2F, 0x18 *Select input MEDIA Num +10, Num 1 47, 60 0x2F, 0x3C *Select input DIG1 Num +10, Num 2 47, 61 0x2F, 0x3D *Select input DIG2 Num +10, Num 3 47, 62 0x2F, 0x3E *Select input DIG3 Num +10, Num 4 47, 63 0x2F, 0x3F *Select input DIG4 Num +10, Num 5 47, 3 0x2F, 0x03 *Select input PC

* Requires MM30 board

27

PRE32 Remote Control Commands RC5 address = 24 (0x18) bits: 0x0600 = 0000 0110 0000 0000 (=1536) xxxx tsss ssdd dddd (s ssss = 1 1000 = 0x18 = 24) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands

IR Dec. Value Hex Value Description Toggle standby 50 0x32 Standby on/off toggle

Standby 1 0x01 Only standby Operate 2 0x02 Only Operate Arrow up 30 0x1E input / menu up

Arrow down 31 0x1F input / menu down Select 43 0x2B Menu navigation Return 46 0x30 Menu navigation

Arrow right 8 0x08 Menu navigation Arrow left 9 0x09 Menu navigation

Menu 0 0x00 Menu navigation Setup 11 0x0B Menu navigation

Balance 26 0x1A Master balance toggle Mute 49 0x31 Mute toggle

Plus / Vol+ 16 0x10 Volume up Minus / Vol- 17 0x11 Volume down

Dim 10 0x0A Toggle dim levels Menu (Top Level) 65 0x41 Menu navigation

Num 1 13 0x0D Select input IN1 Num 2 14 0x0E Select input IN2 Num 3 15 0x0F Select input IN3 Num 4 18 0x12 Select input IN4 Num 5 19 0x13 Select input IN5 Num 6 20 0x14 Select input IN6

Num +10, Num 0 47, 24 0x2F, 0x18 *Select input MEDIA Num +10, Num 1 47, 13 0x2F, 0x0D *Select input DIG1 Num +10, Num 2 47, 14 0x2F, 0x0E *Select input DIG2 Num +10, Num 3 47, 15 0x2F, 0x0F *Select input DIG3 Num +10, Num 4 47, 18 0x2F, 0x12 *Select input DIG4 Num +10, Num 5 47, 19 0x2F, 0x13 *Select input PC

* Requires MM30 board

28

NP30 Remote Control Commands RC5 address = 13 (0x0D) bits: 0x0340 = 0000 0011 0100 0000 (=832) xxxx tsss ssdd dddd (s ssss = 0 1101 = 0x0D = 13) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands

IR Dec. Value Hex Value Description Toggle standby 12 0x0C Standby on/off toggle Standby 1 0x01 Only standby Operate 2 0x02 Only Operate Arrow up 19 0x13 input / menu up Arrow down 25 0x19 input / menu down Select 21 0x15 Menu navigation Return 46 0x2E Menu navigation Arrow right 22 0x16 In Menu: Enter; Otherwise volume up Arrow left 20 0x14 In Menu: Return; Otherwise volume down Menu 49 0x31 Menu toggle Setup 48 0x30 Menu toggle Mute 26 0x31 Mute toggle Dim 10 0x0A Toggle dim Num 1 8 0x08 Select input 1, select menu item 1 Num 2 9 0x09 Select input 2, select menu item 2 Num 3 11 0x0B Select input 3, select menu item 3 Num 4 13 0x0D Select input 4, select menu item 4 Num 5 14 0x0E Select input PC, select menu item 5 Num 6 15 0x0F Select input MEDIA, select menu item 6 Num 7 16 0x10 Select menu item 7 Num 8 17 0x11 Select menu item 8

29

DAC30 Remote Control Commands RC5 address = 13 (0x0D) bits: 0x0340 = 0000 0011 0100 0000 (=832) xxxx tsss ssdd dddd (s ssss = 0 1101 = 0x0D = 13) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands

IR Dec. Value Hex Value Description Toggle standby 12 0x0C Standby on/off toggle Standby 1 0x01 Only standby Operate 2 0x02 Only Operate Arrow up 19 0x13 input / menu up Arrow down 25 0x19 input / menu down Dim 10 0x0A Toggle dim Num 1 8 0x08 Select input 1, select menu item 1 Num 2 9 0x09 Select input 2, select menu item 2 Num 3 11 0x0B Select input 3, select menu item 3 Num 4 13 0x0D Select input 4, select menu item 4 Num 5 14 0x0E Select input PC, select menu item 5 Num 6 15 0x0F Select input MEDIA, select menu item 6 Num 7 16 0x10 Select menu item 7 Num 8 17 0x11 Select menu item 8

30

BD32 Remote Control Commands RC5 address = 30 (0x1E) bits: 0x0780 = 0000 0111 1000 0000 (=1920) xxxx tsss ssdd dddd (s ssss = 1 1110 = 0xE = 30) x=not used t=toggle bit s=system bits (address) d=command (VALUE below) short press (default) = 1 command. long press = 3 consecutive identical commands

IR Dec. Value Hex Value Description Toggle Standby 12 0x0C ON 18 0x12 OFF 19 0x13 Open (Eject) 45 0x2D Setup 44 0x2C Source (1.5s delay) 14 0x0E Source direct 24 0x18 Play 53 0x35 Pause 48 0x30 Stop 54 0x36 Reverse (<<) 50 0x32 Forward (>>) 52 0x34 Skip Next (>>|) 32 0x20 Skip Prev (|<<) 33 0x21 AB Replay (Repeat) 59 0x3B Repeat 29 0x1D Top menu 47 0x2F Pop-up menu 63 0x3F Goto 55 0x37 Return 60 0x3C 0 0 0x00 1 1 0x01 2 2 0x02 3 3 0x03 4 4 0x04 5 5 0x05 6 6 0x06 7 7 0x07 8 8 0x08 9 9 0x09 Cancel 49 0x31

31

Up 15 0x0F Down 25 0x19 Left 20 0x14 Right 22 0x16 Enter 21 0x15 Red 40 0x28 Green 41 0x29 Blue 42 0x2A Yellow 43 0x2B Subtitle 23 0x17 Audio 28 0x1C Angle 57 0x39 Zoom 56 0x38 SAP 36 0x24 PIP 37 0x25 Display 51 0x33 Home 61 0x3D Dimmer 11 0x0B Light 62 0x3E Page up 35 0x23 Page down 34 0x22 Volume up 16 0x10 Volume down 17 0x11 Mute 13 0x0D Pure Audio 38 0x26 P/N 39 0x27 HDMI, resolution 58 0x3A

32

History V16 Added: DVD-30, Sp31 (new model) V25 codes corrected. Date / revision number added to first page. V17 Updated DVD-30 codes V18 Added: I30, I21 DVD-26, CD21, CD31, Delaybox Minor error corrections (Text & layout). Primare Logo changed V19 Changed to SP31 / SPA21, Removed “new model”. Bugs in SPA21 / SPA20 list corrected “record path” Bugs in DVD-26 corrected “Random, “serchmode” V20 Added T22 and T23, added SPA21 on the first page. Added Cdi10. V2.1 Changed version system to X.X, because of confusion with Primare V20 DVD-player Added DVDi10 and SP32/SPA22 Fixed various errors in system address Descriptions V2.2 Added all Hex. Values. V2.3 Added CD32, I32. V2.4 Added new commands for I32 with MM30. Added PRE32, NP30, DAC30, BD32

33