REHAU CONNECTION SYSTEMS · REHAU CONNECTION SYSTEMS ... (e.g. with shifting groundwater level)....
Transcript of REHAU CONNECTION SYSTEMS · REHAU CONNECTION SYSTEMS ... (e.g. with shifting groundwater level)....
REHAU CONNECTION SYSTEMSAWADOCK® FOR SEALED HOUSE CONNECTIONS
Valid from January 2009
296050/5 – Subject to technical modifi cations
www.rehau.com
Construction
Automotive
Industry
2
CONTENTSREHAU CONNECTION SYSTEMS
INGENIOUSLY SIMPLE, SIMPLY INGENIOUS: AWADOCK FROM REHAU
Page
Damaged Side Inlets – Not Unusual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
AWADOCK NEW GENERATION
- The Revolution in Sewer Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
- Seals Leaks Automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
- On the IKT Test Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
- With Ball Joint and for Composite Sewer Pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
These Product Advantages Ensure Durability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
AWADOCK for Thick Walled and Multi-Layer Reinforced Concrete Pipes . . . . . . . . . . . . . . . . . . . . 132
AWADOCK T-Flex – The Connection To Plastic Pipes with Smooth Exteriors . . . . . . . . . . . . . . . . . 133
AWADOCK Connection System Fitting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
AWADOCK Tender Specifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
AWADOCK Connection Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Product Range and Price Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
3
AWADOCK offers numerous variants for the
connection of polymers and traditional materials
to concrete, reinforced concrete and vitrifi ed clay
pipes.
Moreover, with special AWADOCK types, it is also
possible to connect to main sewers with smooth
exteriors and to drop structures.
Your REHAU sales offi ce will be happy to help with
any further queries.
4
Percentage Distribution of Sewer Damages
20% damaged connections
Source: results of the 2004 DWA survey
One out of fi ve occurrences of damage in sewer
networks involves side connections. As such,
according to the result of the 2004 DWA survey on
“condition of the sewer system in Germany”, these
symptoms represent the majority of sewer dama-
ges. System managers rate damaged connections
as the most common faults (see diagram below).
An incorrectly made connection to the sewer pipe
causes the following symptoms:
- Leaking connections as a result of missing or
unsuitable fi ttings
- Inward projecting pipes
- Ingrown roots
Consequences of Damaged Side Inlets:
- Contamination of the groundwater by escaping
sewage
- Additional loads on sewage treatment plants as a
result of infi ltration water
- Pipe blockages
DAMAGED SIDE INLETS NOT UNUSUAL
Damaged side inlet
Damaged side inlet – inward projecting pipe socket
5
AWADOCK NEW GENERATIONTHE REVOLUTION IN SEWER CONNECTION
This safety principle works in a similar way to the
airbag, which reduces the risk of head and chest
injuries in the event of a car crash. However, the
airbag is not a substitute for a seatbelt but rather
only an addition. The statistics show that the belt
is still the principal lifesaver in the case of car
accidents. Airbags signifi cantly increase the safety
of occupants.
In a fi gurative sense, the reliable, tried and tested
AWADOCK connecting seal is comparable with the
seatbelt. The new second seal takes on the role of
the airbag in the system. If a leak occurs between
the drill hole and the seal, the green “airbag seal”
absorbs the water, expands its volume, and
therefore closes the leak. The permanent seal is
thus restored.
Fraunhofer Institute Develops Q-TE-C®
The green “airbag seal” is called Q-TE-C and is
a swelling thermoplastic elastomeric composite.
This seal was developed with Fraunhofer UMSICHT
specifi cally for the application of the AWADOCK
connection system. It starts to swell and seals leaks
when it comes into contact with water.
The airbag revolutionised safety technology in the automotive
industry.
The brand new “AWADOCK NEW GENERATION“ connection system
combines ingenious functionality with unique safety technology.
The airbag can save lives.
Unswollen (left) and swollen Q-TE-C sample.
AWADOCK NEW GENERATION
6
Features and Advantages of the Q-TE-C Material
- Reliable swelling capacity
- High cycle capacity; the ability to absorb and
retain water is maintained permanently even
with frequent changing between dry and wet
(e.g. with shifting groundwater level).
- Dimensionally stable even when swollen
- High water retention capacity under compressive
load
- Seal directly at the point of leakage
- Swelling pressure engineered specifi cally for the
product application
AWADOCK NEW GENERATION Structure
The seal effect of the previous AWADOCK design
remains in place without restriction.
This means that a large drill hole tolerance of a total
of 3 mm (200 -1/+2 mm) is still permitted.
Despite this ability to compensate for such large
tolerances, it is not always possible to eliminate
defects, e.g. such as voids in the drill hole soffi t or
skewed drilling.
As such, with the Q-TE-C seal, a new safety feature
has now been incorporated, which is able to provide
a subsequent seal in case of damage.
0%
50%
100%
150%
200%
250%
300%
350%
Time [h]
FLiq
uid
abso
rptio
n %
0 h 1 h 2 h 4 h 24 h 48 h 72 h
Liquid absorption of Q-TE-C depending on duration of swelling
Here, the swelling seal is inserted into a groove in
the connecting seal and presses against the hole
soffi t. The Q-TE-C seal is encapsulated by two
further sealing lips above and below the sealing
groove, which thus ensure additional sealing.
7
How AWADOCK NEW GENERATION Works
In certain installation situations, the hole soffi t may
have larger fl aws, e.g. voids, score marks, or the hole
is drilled at a slight angle to the pipe axis.
The connection leaks. Groundwater enters the main
sewer.
In 10 to 24 hours, the Q-TE-C starts to swell. The
seal starts to work.
Nach ca. 48 bis 72 Stunden erfolgt die dauerhafte
After approx. 48 to 72, the leak is permanently
sealed. The Q-TE-C seal is encapsulated in the
connecting seal in such a way that the water is
retained. Drying out is minimised.
AWADOCK NEW GENERATIONSEALS LEAKS AUTOMATICALLY
nach
Frequently Asked Questions
How many swelling cycles can be achieved with
Q-TE-C?
Ongoing investigations into cycle capacity are being
conducted at Fraunhofer UMSICHT. At present, it
can already be stated that the water absorption
functions reliably even after several dozen cycles.
Is such a high cycle capacity actually necessary in
the sewer?
The number of cycles should be defi ned by the
performance of the material. In the sewer, this
remains at only a few cycles. On the one hand, the
Q-TE-C seal is encapsulated in the connecting seal
in such a way that the water is held in the seal. On
the other hand, complete drying out would happen
only in a warm, dry airfl ow. The relative atmosphe-
ric humidity of over 90 % in the sewer is suffi cient
to prevent drying out.
Why does swelling not begin immediately on
contact with water?
In order to also continue to guarantee practical and
easy installation on the construction site, REHAU
has developed the seal in such a way that notice-
able swelling starts only between 10 and 24 hours
later. As such, the seal does not swell unintentional-
ly before installation, e.g. in the case of accidentally
damp storage on the construction site.nach
8
Have any weaknesses been found in AWADOCK to
date?
No. On the contrary: The AWADOCK screw
principle with the conical structure has been
roven 100,000 times.
AAWADOCK NEW GENERATION on the IKT Test
Stand
Based on the trials in the house connection nozzle
product tests, REHAU has commissioned new
practical tests from the institute for underground
infrastructure (IKT), some of which are under tighter
test conditions.
The following tests have been conducted:
1. Seal for a standard hole within drill hole
tolerances of 200 + 2/-1 mmm
2. Seal for a hole outside of the tolerance range –
204 mm hole – e.g. caused by uneven drill bit
3. Seal after skewed drilling (5° deviation) –
possible source of faults particularly in the case
of small main pipes
The Result is Obvious:
The AWADOCK connection system guarantees
the seal and function even under these diffi cult
surrounding conditions. In tests 2 and 3, AWADOCK
with Q-TE-C sealed off the leaks after max. 48
hours.
As these test parameters surpass the standard
manufacturer specifi cations on the market, IKT
awarded the AWADOCK NEW GENERATION “IKT
tested“ seal.
AWADOCK DN 160 achieves “VERY GOOD”
in the IKT product test
AWADOCK NEW GENERATIONON THE IKT TEST STAND
AWADOCK is one of the most purchased house
connection systems and was awarded the rating
“VERY GOOD” in the IKT “house connection nozzles
– 2002 status” product test. AWADOCK with
Q-TE-C provides even greater assurance in
installation and operation – with safety for
generations.
9
AWADOCK Providing the Ball – For Even Grea-
ter Flexibility
A new design is being added to the AWADOCK
connection system for the connection of DN 160 PP
or PVC pipes to concrete, reinforced concrete and
vitrifi ed clay pipes.
A ball joint is integrated into the screw sleeve,
so the connected secondary pipe can be angled
horizontally or vertically by ± 7.5° at infi nitely
variable intervals.
This fl exibility makes installation easier, particularly
in confi ned pipe trenches.
AWADOCK NEW GENERATION with ball valve
± 7.5° connection with infi nitely variable horizontal or vertical
angling
AWADOCK CP Type A – internal view
AWADOCK NEW GENERATIONAWADOCK WITH BALL JOINT
AWADOCK FOR COMPOSITE SEWER PIPES
Properties:
- PP screw sleeve with SBR versatile connecting seal
- Three variants for size range DN/OD 315-DN/
OD 1200
- DN 160 connection for pipes from DN/OD 315
to DN/ID 800
- DN 200 connection for pipes from DN/OD 800
to DN/OD 1200
Advantages:
- Universally usable for all standard composite
pipes available on the market, in accordance
with DIN EN 13476
- Simple, quick and reliable to screw in
- Permanently sealed up to 0.5 bar
AWADOCK CP
Side Connection for Composite Sewer Pipes.
AWADOCK CP (corrugated pipes) guarantees the
sealed and reliable connection of KG DN 160/200
side inlets to composite sewer pipes.
With three variants, the connecting seals developed
specifi cally for these cover connections to main
sewer pipes from DN/OD 315 to DN/OD 1200. As
such, AWADOCK CP is a winner with its simple,
universal, reliable application and permanent seal
up to 0.5 bar.
10
Permanent Seal
The conical screw sleeve is screwed into the con-
necting seal. The entire surface of the seal presses
against the drill hole and even the sealing require-
ments of DIN EN 1610 are surpassed: the seal has
been proven in trials up to 1 bar.
Installation – Simply and Quickly Screwed In:
- Centre drill with core drill and de-burr the hole
- Insert the connecting seal
- Apply lubricant
- Firmly screw in the conical screw sleeve with the
installation wrench
- Connect the pipe. Done!
AWADOCK NEW GENERATIONTHESE PRODUCT ADVANTAGES ENSURE DURABILITY
Permanent seal
Installation – simple and quick
No Inward Projecting Pipes
A rebate in the screw sleeve prevents the connec-
ting pipe from protruding into the main sewer.
Corrosion Protection
The cut reinforced steel in reinforced concrete pipes
is reliably protected from corrosion by connecting
seals of different lengths. The seal and connection
lengths match the wall thicknesses of the main
sewer (type A/B/C/D…).
High Expulsion Resistance in the Pressure Test
When the conical screw sleeve is screwed into the
connecting seal, a high surface pressure is produced
against the drill hole. This results in a high level of
expulsion resistance.
11
“Very Good” in IKT Product Test (2002 Status)
and IKT Tested!
Impervious to Shear Loads and Angling
Shear loads and angling occur as the result of the
different settlement behaviour of the main and con-
necting pipes. Sealing below the house connection
nozzle also presents a problem.
For this reason too, ATV-DVWK-139 pt. 9 demands
fl exibility in the connections. They must be able to
“absorb movement. Possible settlement and the
resulting loads in the connection area” should be
taken into account.
The AWADOCK connection system meets these
requirements by the compression of the high-
volume connecting seal. It was rated “VERY GOOD”
for both loads in the IKT product test.
Approved by the General Building Inspectorate
Under Z-42.1-348
Flexible
New AWADOCK screw sleeve with ball joint allows
angling of ± 7.5° and makes installation easier in
confi ned pipe trenches.
Greater Drill Hole Tolerance – Greater Safety
During Installation
The green “airbag seal“ (Q-TE-C) can permanently
seal leaks between the drill hole and the connecting
seal, e.g. as the result of defective drilling.
With wide, solid connecting seals, drill hole tole-
rances of + 2 mm to -1 mm can be bridged.
Safety for Generations
All connection nozzles in the AWADOCK product
range are fi tted with the new Q-TE-C seal.
Internal Lettering Provides Information
The front of the connecting seal holds the following
important information:
- Brand
- Product name
- AWADOCK type (A, B, C…)
- Year and month of production
When the pipe is removed, it is therefore possible to
check that the correct product has been installed.
Moreover, the product will still be identifi able 50 or
80 years later.
12
1
2
3
The set comprises:1 A connecting seal, matched to the wall
thickness of the pipe, with a closing lip on
the inside2 A screw sleeve – designed as a pipe
breakthrough3 A concave chamfered AWADUKT PP SN4
connecting pipe, which compresses the
closing lip of the seal4 Lubricant and fi tting instructions
AWADOCK® FOR THICK WALLED AND MULTI-LAYER REINFORCED
CONCRETE PIPES
AWADOCK for Thick Walled and Multi-Layer
Reinforced Concrete Pipes
4
13
AWADOCK T-Flex connection system for the retrospective connection
of PVC and PP sewer pipes in sizes DN/OD 110 to DN/OD 200 to
main sewer pipes with smooth surfaces.
- The seal is generated on the outside wall of the pipe and not in the
hole. With the AWADOCK T-Flex connection system, large tolerances
are possible for drilling, i.e. standard drill bits can be used.
- The comprehensive external seal ensures the seal effect even when
the pipe is slightly deformed.
- Very easy and quick installation
- Flexible connection, absorbs ground settlement and prevents
shearing
- Root-proof
- An integrated pipe rebate prevents protrusion into the main pipe.
AWADOCK T-FLEX -THE CONNECTION TO PLASTIC PIPES WITH SMOOTH EXTERIORS
Usage Recommendation for the AWADOCK T-Flex Types
Depending on the connection and main sewer pipe, the following
AWADOCK T-Flex types are to be used:
DN/OD External-Ø External-Ø Core hole
Connecting pipe Main pipe (mm)
110 105 - 120 200 - 400 117 - 125
160 150 - 170 250 - 500 167 - 175
200 175 - 200 300 - 500 203 - 213
Fitting:
Step 1:
Use a drill to create a core hole
(see usage recommendation).
Ensure that the hole is made at
an angle of 90° to the pipe axis.
Step 2:
Cleanly de-burr the edge of the
core hole.
Step 3:
Place the AWADOCK T-Flex
connecting element centrally on
the drill hole.
Step 4:
Fix AWADOCK T-Flex to the main
pipe using both steel clips. When
doing this, ensure that the clips
are passed through the correct
openings.
Step 5:
Firmly tighten both tensioning
straps (10 Nm) and shorten if
necessary.
Step 6:
Insert the connecting pipe to the
integrated rebate. Tighten the
tensioning strap (6 Nm).
Advice for Drilling Cast und
Plastic Pipes:
- The minimum spacing between
two connections to one cast or
plastic pipe should be 1 m.
- Avoid drilling a second hole
directly opposite.
14
Specifi cations for Storage and Installation#
- Store AWADOCK with Q-TE-C dry and protected from the wet.
- Protect from wet until shortly before installation, in order to prevent unintended swelling before installation.
- Observe the fi tting instructions on all AWADOCK packaging.
When fi tting the AWADOCK connection system , please observe the
following stages:
Step 1:
Use a core drill to create a hole at the point to be connected. For hole
diameter, see the table. Check the hole soffi t for defective points and
correct if necessary.
AWADOCK® CONNECTION SYSTEMFITTING INSTRUCTIONS
Create a hole
Screw the AWADOCK screw sleeve into the connecting seal
Insert the AWADOCK connecting seal into the hole
Insert the pipe into the AWADOCK screw sleeve up to the rebate
Step 3:
Lubricate the internal thread of the AWADOCK connecting seal.
Then, using the installation wrench (special accessories), evenly and
centrically screw the AWADOCK screw sleeve into the connecting seal
to the fi nal turn of the thread.
Step 2:
Insert the AWADOCK connecting seal into the hole. Ensure that the
closing lip of the connecting seal lies fl ush with the external concrete
wall. The arrows on the seal point lengthwise along the pipe.
Step 4:
Lubricate the spigot end of the pipe to be connected and insert it into
the AWADOCK screw sleeve up to the rebate.
15
Tender specifi cations are available from the REHAU sales offi ce or as
an internet download from www.rehau.de/tiefbau.
Sewer Connection Systems
DN/OD 160/90° Saddle Piece with Ball Joint, KG Concrete,
Clayware Concrete, Clayware
DN/OD 160/90° saddle piece with polypropylene conical screw sleeve
with integrated ball joint; the pipe can be angled in ball joint between
0 and 7.5°(total 15°) at infi nitely variable intervals in all directions.
SBR connecting seal with internal thread and additional swelling
thermoplastic elastomer seal, with building inspectorate authorisation
Z-42.1-348.
Saddle piece for side connection of DN/OD 160 sewer pipes with
smooth walls to concrete or reinforced concrete pipes, in accordance
with DIN 4032/4035 or DIN EN 1916, or clayware pipes in accor-
dance with EN 295 DN ___; wall thickness approx.: __ mm
Correct connection to the sewer using a core drill (hole: 200 mm
+2/-1 mm) must be calculated into the piece price.
Saddle piece with ball joint, e.g. REHAU AWADOCK NEW GENERATI-
ON with ball joint or equivalent art.
Make / type offered:
_____________________________________
To be completed by the bidder
1.00 Pc.
DN/OD 200/90° Saddle Piece, KG Concrete, Clayware Concrete,
Clayware
DN/OD 200/90° saddle piece with polypropylene conical screw slee-
ve. SBR connecting seal with internal thread and additional swelling
thermoplastic elastomer seal, with building inspectorate authorisation
Z-42.1-348.
Saddle piece for the side connection of DN/OD 200 sewer pipes with
smooth walls to concrete or reinforced concrete pipes, in accordance
with DIN 4032/4035 or DIN EN 1916, or vitrifi ed clay pipes in accor-
dance with EN 295 DN ___; wall thickness approx.: __ mm
Correct connection to the sewer using a core drill (hole: 257 mm
+2/-1 mm) must be calculated into the piece price.
Saddle piece with ball joint, e.g. REHAU AWADOCK NEW GENERATI-
ON with ball joint or equivalent art.
Make / type offered:
_____________________________________
To be completed by the bidder
1.00 Pc.
Connection nozzles
Wall thickness of the main pipe
in mmMain pipe diameter
KG connection VCP connectionGlass fi bre reinforced
plastic / cast connection
KG wall breakthrough KG conne
AWADOCKDN/OD 160
With ball joint
AWADOCKDN/OD 160
AWADOCKDN/OD 200
AWADOCK VCPDN/ID 150
Glass fi bre reinforced plastic / castDN/ID 150
AWADOCK MDDN/OD 160
AWADOCK MDDN/OD 200
Combi setDN/OD 250
Diameter Hole200 + 2 mm - 1 mm
200 + 2 mm - 1 mm
257 + 2 mm - 1 mm
200 + 2 mm - 1 mm
200 + 2 mm - 1 mm
200 ± 1 mm 250 ± 1 mm 276 ± 1 mm
Diameter Drill bit 200 mm 200 mm 257 mm 200 mm 200 mm 200 mm 250 mm 276 mm
Connection Main pipe
Concrete/ DIN EN 1916 reinforced
concrete pipes
60-85Type A
179950-500Type A
176001-500
Type A170501-500
(just connectable) from DN 400)
Type A176051-500
Type A176151-500
85-115Type B
179960-500Type B
176011-500Type B
170511-500Type B
176061-500Type B
176161-500
115-160Type C
179970-500Type C
176021-500Type C
170521-500Type C
176071-500Type C
176171-500
160-175Type D
179980-500Type D
176041-500Type D
176009-500
180-195Type E
176005-500Type E
176014-500
200-215Type F
176006-500Type F
176015-500
220-235Type G
176007-500Type G
176016-500
240-250Type H
176008-500Type H
176017-500
≥ 60 ≥ DN 500 176231-001
≥ 60 ≥ DN 600
≥ 60 ≥ DN 800
DIN EN 295-1 vitrifi ed clay
pipes
37-60 ≥ DN 300Type K
179990-500Type K
176201-500
Type K 170541-500
(erst anschließbarab DN 400)
Type K 176211-500
60-85Type A
179950-500Type A
176001-500Type A
170501-500Type A
176051-500Type A
176151-500
DIN EN 1916 concrete shafts
fl at walls and rec-tangular concrete
shafts≥ 60
170991-500171001-500171021-500
171391-500
AWASCHACHT PPDN 1000
Pipes with smooth exteriors: e.g. PP in accor-dance with DIN EN 1852, PVC in accordance with
DIN EN 1401
DN 200-DN 400
DN 250-DN 500
DN 315-DN 500
DIN EN 13476 composite sewer
pipes
DN OD 315-DN ID 400
DN OD 500 -DN ID 800
DN OD 800 -DN OD 1200
Suitable tools
Installation wrench 176111-500/520
Drill bit / hole saw 176301-001 176321-001 176301-001 - 176047-100
16
AWADOCK Connection Options
17
ection to concrete pipes KG/VCP connection to concrete shaftKG connection to plastic pipes with smooth
exteriorsKG connection to AWASCHACHT
KG connection to composite sewer pipes
Combi set DN/OD 315
Combi setDN/OD 400
AWADOCK KGDN/OD 160
AWADOCK KGDN/OD 200
AWADOCKVCP
DN/ID 150
AWADOCK T-FlexDN/OD 110
AWADOCK T-FlexDN/OD 160
AWADOCK T-FlexDN/OD 200
AWADOCK KGDN/OD 160
AWADOCK KGDN/OD 200
AWADOCK CPDN/OD 160
AWADOCK CPDN/OD 200
341 ± 1 mm 426 ± 1 mm 200 + 2 mm - 1 mm
257 + 2 mm - 1 mm
200 + 2 mm - 1 mm
117-125 mm 167-175 mm 203-213 mm 200 ± 1 mm 250 ± 1 mm 200 + 3 mm - 1 mm
250 + 3 mm - 1 mm
341 mm 426 mm 200 mm 257 mm 200 mm 122 mm 172 mm 212 mm 200 mm 250 mm 200 mm 250 mm
176241-001
176251-001
170551-500 170561-500 170571-500
190365-200191175-200
191345-200191355-200
170611-001
170621-001
170631-001
191780-160
191790-160
191800-200
176111-500/520 176111-500/520
176048-100 176049-100 176301-001 176321-001 176301-001 170671-001 170681-001 170691-001 190028-100 190457-001 190028-100 190457-001
18
L
AWADOCK NEW GENERATION with Ball Joint
Connection of PVC and PP DN 160 sewer pipes to concrete or rein-
forced concrete pipes
Material: elastomer/Q-TE-C/PP
Colour: black/green
PRODUCT RANGE AND PRICE SUMMARY
Connection of PVC and PP Sewer Pipes to Concrete or Rein-
forced Concrete Pipes
Material: elastomer/Q-TE-C/PP
Colour: black/green
Art.-Nr. DN/OD Type1) L [mm] Pc./Pal . €/pc.*
170501-500 200 A 60 45 116,00
170511-500 200 B 80 45 129,00
170521-500 200 C 110 45 142,00
DN 200 connection of other pipe materials possible with adaptor.
AWADOCK KG Concrete DN 160
AWADOCK KG Concrete DN 200
Art. No . DN/OD Type1) L [mm] Pc./Pal . €/pc.*
176001-500 160 A 60 75 56,50
176011-500 160 B 80 75 71,00
176021-500 160 C 110 60 84,50
176041-500 160 D 155 45 139,00
Art. No . DN/OD Type1) L [mm] Pc./Pal . €/pc.*
179950-500 160 A 60 45 65,00
179960-500 160 B 80 45 77,00
179970-500 160 C 110 45 90,00
179980-500 160 D 155 30 139,00
19
1) To see which AWADOCK type is required for which main pipe diameter, please refer to page 136.
* Prices apply to the entire AWADOCK mounting set (connecting seal, screw sleeve, lubricant and fi tting instructions)
Art. No . DN Type1) L [mm] Pc./Pal . €/pc.*
176051-500 150 A 60 45 57,50
176061-500 150 B 80 45 71,00
176071-500 150 C 110 45 85,00
External connecting pipe diameter: 186 mm
Connection of vitrifi ed clay pipes, Ductile Iron and Glass Fibre
Reinforced Plastic Sewer Pipes to Concrete or Reinforced
Concrete Pipes
Material: elastomer/Q-TE-C/PP
Colour: black/green
AWADOCK Clayware Concrete DN 150
Art. No . DN Type1) L [mm] Pc./Pal . €/pc.*
176151-500 150 A 60 Individual 69,00
176161-500 150 B 80 Individual 83,00
176171-500 150 C 110 Individual 96,00
External connecting pipe diameter: 168-170 mm
AWADOCK Glass Fibre Reinforced Plastic / Cast Concrete DN 150
Connection of DN 150 PVC, PP and VCP Sewer
Pipes to VCP
Material: elastomer/Q-TE-C/PP
Colour: black/green
Art. No . Description/Type Type L [mm] Pc./Pal . €/pc.*
176201-500 AWADOCK KG VCP DN 160 K 37 90 59,00
170541-500 AWADOCK KG VCP DN 200 K 40 35 119,00
176211-500 AWADOCK VCP-VCP DN 150 K 37 75 65,00
179990-500 AWADOCK KG VCP DN 160 with ball joint K 37 60 75,00
20
L
Internal drop with curve
AWADOCK as Drop or Bypass for Connection to
Concrete Shafts
Flat internal seal, AWADOCK spigot end
DN/OD 160
Material: elastomer/Q-TE-C/PP
Colour: black/green
Art . No. Pc./Pal . €/pc.*
170551-200 AWADOCK DN 160 75 94,00
170561-200 AWADOCK DN 200 35 155,00
170571-200 AWADOCK clayware DN 150 45 94,00
AWADOCK Type K/U (short/bypass)
Connection of PVC and PP Sewer Pipes to Tried and
Tested Thick Walled and Multi-Layer Reinforced
Concrete Pipes in Accordance with DIN 1916
Comprising a connection seal matched to the
wall thickness, a screw sleeve designed as a
pipe break-through, and a concave chamfered
AWADUKT PP SN4 connecting pipe
Material: elastomer/Q-TE-C/PP
Colour: black/green
Art. No DN/OD Type L [mm] Reinforced Concrete Packaging €/pc.
Pipe Wall Thickness Unit
176005-500 160 E 175 180-195 Individual 220,00
176006-500 160 F 195 200-215 Individual 225,00
176007-500 160 G 215 220-235 Individual 235,00
176008-500 160 H 235 240-250 Individual 245,00
AWADOCK KG DN 160 to Thick Walled Reinforced Concrete Pipes
AWADOCK KG DN 200 to Thick Walled Reinforced Concrete Pipes
Art. No DN/OD Type L [mm] Reinforced Concrete Packaging €/pc.
Pipe Wall Thickness Unit
176009-500 200 D 155 155-175 Individual 218,00
176014-500 200 E 175 180-195 Individual 260,00
176015-500 200 F 195 200-215 Individual 270,00
176016-500 200 G 215 220-235 Individual 280,00
176017-500 200 H 235 240-250 Individual 300,00
Need an AWADOCK for a greater wall thickness? Ask us!
21
Wall Breakthrough for Side Connection to Flat Walls –
KG Connection
Material: elastomer/PP
Colour: black/green
Art. No. DN/OD Packaging Unit €/pc.*
171001-500 AWADOCK wall breakthrough 160 single 79,00
170991-500 AWADOCK wall breakthrough inc. internal breakthrough pipe and
connection seal
160 single 129,00
171021-200 AWADOCK shaft connection to fl at concrete wall as shaft drop
moulding, type K/U
160 single 89,00
171391-500 NEW AWADOCK wall breakthrough (available from March 2009) 200 single 129,00
Art. No. Type DN/OD Packaging Unit €/pc.
190365-200 Standard 160 single 56,00
191175-200 K/U (design as below on page 146) 160 single 66,50
191345-200 NEW Standard 200 single 116,00
191355-200 NEW K/U (design as below on page 146) 200 single 126,00
Connection of PVC and PP Sewer Pipes to
REHAU AWASCHACHT PP DN 1000
Material: elastomer/PP
Colour: black/green
AWADOCK KG to AWASCHACHT
Connection of PVC and PP Sewer Pipes to Double Wall Sewer
Pipes (Corrugated Pipes)
Material: elastomer/PP
Colour: black/green
AWADOCK KG-CP
Art. No. DN/OD Type Composite Pipe Diameter €/pc.
191780-160 NEW 160 A DN OD 315 - DN ID 400 79,00
191790-160 NEW 160 B DN OD 500 - DN ID 800 83,00
191800-200 NEW 200 C DN OD 800 - DN OD 1200 89,00
AWADOCK KG-CP Type A
22
Art. No. DN/OD External Ø [mm] External Ø Core Hole Pc./Packaging Uit €/pc.
Connecting pipe Main Pipe [mm]
170611-001 110 105-120 200-400 117-125 4 55,00
170621-001 160 150-170 250-500 167-175 4 85,00
170631-001 200 175-200 300-500 203-213 7 119,00
AWADOCK T-FLEX
Connection for sewer pipe systems with smooth
exteriors
Material: stainless steel / EPDM
Art. No. PEX €/pc.
176111-500 Standard single 48,00
This installation wrench has been designed specifi cally for the application of AWADOCK and can be used universally for all types.
Installation Wrench for AWADOCK
Material: stainless steel
Colour: silver
Art. No. d1
t BL Hole €/pc.
[mm] [mm] [mm] [mm]
176231-200 250 135 500 276 89,00
176241-200 315 145 500 341 109,00
176251-200 400 170 500 426 169,00
Combi Set Connection System
Comprising connection seal and AWADUKT PP SN 10 pipe
0.5 m
Material: RAU-PP 2300 / SBR
Colour: Orange-brown / black
23
Art. No. Ø in mm Connection 3-day rental* €/pc.
176301-001 200 1 1/4” UNC sleeve - 349,00
176321-001 257 1 1/4” UNC sleeve 69,00 599,00
176047-001 NEW 276 1 1/4” UNC sleeve 89,00 980,00
176048-001 NEW 341 1 1/4” UNC sleeve 119,00 1190,00
176049-001 NEW 426 1 1/4” UNC sleeve 159,00 1600,00
* Not discountable + deposit
Art. No. Ø in mm 3-day rental* €/pc.
190028-100 NEW 200 59,00 549,00
190457-001 NEW 250 89,00 739,00
* Not discountable + deposit
AWADOCK Diamond Core Bit
For use in concrete and reinforced concrete pipes with soft to hard
aggregate and an average to high level of reinforcement
AWADOCK Hole Saw
For drilling plastic pipes and shafts inc. hole saw socket, drill chuck,
centre drill with ejector, packed in the toolbox
Art. No. For DN Hole [mm] €/pc.
170671-001 110 122 183,00
170681-001 160 172 259,00
170691-001 200 212 309,00
REHAU
AWADOCK T-FLEX Core Bit
Inc. centre drill suitable for drills with a slip clutch
24
www.rehau.com ©REHAU 296050 EN 11.2008
Terms and Conditions of Delivery and Payment:
Goods valued at under € 2,500.00 net ex works, carriage paid to
receiving station for goods valued from € 2,500.00 net for pipes and
mouldings. Carriage extra for express goods, at the expense of the
orderer.
Terms of Payment:
10 days at 2 %, 30 days net only. Delivery and invoicing in accor-
dance with the REHAU terms and conditions of payment and delivery
with which you are familiar. These can be viewed at www.rehau.de/
LZB or sent on request.
Minimum Order Quantity:
Goods valued at € 250.00 net. Other products from the REHAU
standard range may also be included in order to reach this net value
of goods.
Prices:
All prices are exclusive of VAT.
Delivery Period:
All standard products can be delivered immediately from stock.
Product Labelling:
Clear labelling of the product requires indication of the product, mate-
rial and colour numbers.
Subject to technical modifi cations.
RAUBiOXON PLUS aeration tube RAUCLEAN BC small water treatment
plant
AWADUKT Thermo air and geothermal
heat exchanger system
Stormwater seepage with RAUSiKKO-Box
Other REHAU Ranges
Our verbal and written advice relating to technical applications is based on experience and is to the best of our
knowledge correct but is given without obligation.
The use of REHAU products in conditions that are beyond our control or for applications other than those specified
releases us from any obligation in regard to claims made in respect of the products.
We recommend that the suitability of any REHAU product for the intended application should be checked. Utilization
and processing of our products are beyond our control and are therefore exclusively your responsibility. In the event
that a liability is nevertheless considered, any compensation will be limited to the value of the goods supplied by us
and used by you.
Our warranty assumes consistent quality of our products in accordance with our specification and in accordance
with our general conditions of sale.
www.rehau.de/verkaufsbueros