Reece ™ | Plumbing | Duopex Gas |...
Transcript of Reece ™ | Plumbing | Duopex Gas |...
DUOPEXGASMANUAL
THE DUOPEX GAS PIPEAND FITTING SYSTEM ISDESIGNED TO MAKEEVERY JOB QUICK ANDEASY. IT PROVIDES AREVOLUTIONARYALTERNATIVE FOR THEPROFESSIONALPLUMBER ANDGASFITTER.
DUOPEX GAS MANUAL
The DUOPEX-GAS pipe and fitting system is designed as aconsumer system for gas installations in accordance with Table3.1 of Australian Standard (Gas Installations)AS 5601—2004.
All the limiting conditions and the requirements of AS 5601particularly Sections 3 Materials and Components, Section 4Installing Consumer Piping, Section 5 Installing Appliances andthis publication should be strictly adhered to.
The pipe has been tested in accordance with AS4176and carries license number 21044 and Standardsmark.
The DUOPEX GAS pipe has many advantages. Some arelisted below:
• Impermeability to oxygen and gases in general.
• Form stability during installation, for an example in a curve.
• Low thermal conductivity level.
• Light weight during transport and installation.
• Thermal expansion is lower than that of other tubes.
• Very good behaviour in the presence of fire thanks to the metal layer and low steam emission duringcombustion.
• Lower pressure loss thanks to the smooth inner layer.
DUOPEX GAS PIPE
The DUOPEX GAS pipe is a multi layer or composite pipe system.
It consists of an inner layer of cross-linked polyethylene(PE-X), an adhesive layer, an aluminium layer, an adhesivelayer, an outer layer of cross-linked polyethylene, which is effectively a 5-layer pipe.
02_DUOPEX GAS MANUAL
Outer LayerCross-linkedpolyethylene
Adhesive LayerMiddle LayerAluminium
Inner LayerCross-linkedpolyethylene
Adhesive Layer
Forming Stability
After bending the DUOPEX GAS pipe will remain stable,due to the metal layer. In many cases thanks to thischaracteristic, it is possible to prefabricate assembliesbefore delivery to the site.
DUOPEX GAS MANUAL_03
Dimension 16x2 20x2 26x3 32x3 40x3.5 50x4 63x4.5
Coefficient of 0.026 0.026 0.026 0.026 0.026 0.026 0.026Linear ThermalExpansion inmm/m x K
Thermal 0.45 0.45 0.45 0.45 0.45 0.45 0.45Conductivityin W/M x K
Water contents 0.113 0.201 0.314 0.531 0.855 1.385 2.29in 1/m
Radius of 5 x d 5 x d - - - - -curvaturewithout aidsmm
Radius of 2 x d 3 x d - - - - -curvaturewith bendingspring mm
Radius of - - 3.6 x d 3.6 x d 4.0 x d 4.0 x d 4.5 x dcurvaturewith bendingtool mm
Pipe roughness 0.007 0.007 0.007 0.007 0.007 0.007 0.007K mm
Coil Length 50 100 50 50 - - -100
Coil Dimensions 610 x 550 x 550 x 940 x - - -mm inside x 740 x 780 x 780 x 1200 xoutside x 115 190 190 150width 510 x
740 x120
Weight per 5.5 15 15 21coil kg
Metres per 5 5 5 5 5 5 5length
Data Sheet
Minimum Bending RadiiBending can be made manually however if tighter bendsare required bending springs or bending tools can beused.
04_DUOPEX GAS MANUAL
DUOPEX GAS PIPE
Pipe Dimension Max Pipe clip(mm) clearance (cm)
16 x 2.0 10020 x 2.0 12526 x 3.0 15032 x 3.0 20040 x 3.5 20050 x 4.0 25063 x 4.5 250
Thermal Changes in LengthHeating and cooling cause pipe length changes.
The coefficient of expansion of DUOPEX GAS compositepipes is 0.026 mm/m x k
Spacing of Supporting Devises SEE ALSO AS5601 TABLE 4.2
Pipe Bending Bending radiiDimension radii without with internal(mm) tools pipe bending
spring
16 x 2.0 5 x da 2.0 x da
20 x 2.0 5 x da 3.0 x da
Bending radiiwith bending tools
26 x 3.0 3.6 x da
32 x 3.0 3.6 x da
40 x 3.5 4.0 x da
50 x 4.0 4.0 x da
63 x 4.5 4.5 x da
Thermal changes in length
Pipe length changesare caused by heatingand cooling.
The coefficient ofexpansion of DUOPEXcomposite pipes is0.026mm/m x K.
ExampleTemperaturedifferential �T 50kPipe length L 5 mCoefficient of expansion a 0.026 mm/m.KLinear expansion �L 6.5 mm
�L = a x L x �T= 0.0026mm/m . K x 5 m x 50 K= 6.5 mm
Fire and Excessive HeatKeep DUOPEX GAS PIPE a minimum of 500mm fromsources of high heat such as heating appliances and fluesfrom heating appliances.
Keep DUOPEX GAS PIPE 1500mm from slowcombustion type stoves and flues used to heat hot wateror cooking. (Wet back type).
Leave 300mm minimum space between DUOPEX PIPEand recessed electric light fittings.
DUOPEX PIPE should not be positioned within 150mm ofgas or central heating vents or flues.
UV ResistanceDUOPEX GAS PIPES must be protected against directsunlight or UV radiation. Consequently, DUOPEX GASPIPES must be covered during transport or storage if theyhave been removed from their original packaging. WhenDUOPEX GAS PIPES are used in a protective tubeadequate UV protection is assured during the installationphase. Furthermore, jackets made from insulating materialcan undertake the function of UV protection withDUOPEX GAS PIPES.
Chemical ResistanceThe chemical properties of polyethylene are significantlyimproved by cross-linking. Multi layer pipe with cross-linked polyethene has been approved for use in AS5601.This includes Natural gas and LPG. For specific gasesother than these please contact the Duopexrepresentative.
DUOPEX GAS MANUAL_05
Gas Standard AS 5601
4.11.4 - Composite pipe installed above groundshall be protected against degradation fromexposure to ultra violet light.Note: A typical means of protection is sleeving or wrapping with asuitable protective material.
DUOPEX GAS pipes are resistant to thefollowing media:• Concrete, plaster, mortar, and cement.
• Disinfectants and cleaning agents according to DVGWworksheet W 291 and DIN 2000.
• All natural potable water constituents.
• Corrosion - protection agents according to DIN 1988part 4.
DUOPEX GAS pipes must be protected against:• Direct contact with bitumen or bitumen strips.
• Pipes must be protected against greases, solvents and oils.
• Contaminated areas as defined by AS5601 andAS3500.
If the DUOPEX GAS pipe installation system is used inareas where, for example, aggressive gases, permanentlyacting moistures or building materials containing chlorineare to be encountered, the fittings have to be protectedusing suitable jacketing. This also applies to contact withscreed, concrete, mortar or plaster.
Always consult the manufacturer for details.
The pipes have been tested in accordance with ATS5200.478. The testing requirements of this technicalspecification match those in AS4176. The pipes carrywatermark and licence number 21044.
06_DUOPEX GAS MANUAL
DUOPEX GAS PIPE
DUOPEX GAS FITTINGS
The DUOPEX GAS fitting system are manufactured fromdezincification resistance brass with a stainless steelcrimp ring and joined to the pipe using a precision andspecific crimping tool.
The fittings have been tested in accordance with ATS5200.478. The testing requirements of this technicalspecification match those in AS4176. The fittings carrywatermark and licence number 21069.
To increase joint performance all DUOPEX GAS crimpfittings are characterised by a plastic holding ring whichhas 2 important functions:
1. As a locating ring that matches the DUOPEX GAS jawsfor a perfect crimp position.
2. It allows the installer to visually check when the pipe iscorrectly fitted on the fitting.
These pipe fittings are available for DUOPEX GAS in sizesranging from 16 to 63mm.
DUOPEX GAS fittings are classified as a permanent jointin accordance with AS 5601.
DUOPEX GAS MANUAL_07
Female BSP TeeFor the complete range of fittings see pages 18 to 24.
08_DUOPEX GAS MANUAL
AUSPEX JOINTING TOOLS
MINI TOOL
• Battery Powered – hydraulic 9.6 volts/Ah.
• Ergonomic handling.
• Short crimping time (approx.3-4 sec.)
• Automatic piston return and motor cut off.
• 360 degree moveable jaw holder.
• Weight including crimping jaws only 2.5 kg approx.
• System dependent, up to 32mm can be used.
• At 20mm approx. 65 crimps per battery chargepossible.
• Charging time of approx. 40 min.
• Delivery contents: crimping tool, carrying case, chargerand two battery.
• Jaws are available in sizes 16-32mm for DUOPEX GAS.
• Jaws for AUSPEX hot and cold water PE-X system areavailable and are compatible with the AUSPEX mini tool16mm to 25mm.
• The carrying case can be supplied complete with themini tool and accessories.
AUSPEX WATER JAWS 16mm to 25mm
DUOPEX GAS JAWS 16mm to 32mm
DUOPEX GAS MANUAL_09
MAXI TOOL
• Battery powered – hydraulic 12V.
• Lightweight, compact design and construction.
• Ergonomic handle design (one hand operation).
• Short pressure time (depending on pipe diameter,approx. 5 to 7 sec.).
• Automatic piston retraction after reaching operatingpressure, motor cut-off.
• Maintenance and malfunction warnings microprocessor– controlled.
• 360 degree moveable jaw holder.
• Jaw range available from 16 to 63mm.
• Metal carrying case complete with battery-hydraulictool, one battery and charger.
• At medium pipe diameters, approx 150 crimp strokesper battery charge.
DUOPEX GAS JAWS 40mm to 63mm
DUOPEX GAS JAWS 16mm to 32mm
MAKING A JOINT
It is most important that the tool manualsupplied with the tool is read in its entirety andthe user becomes familiar with the maintanence,precautions and the proper use of this tool.
The following describes, in general terms, the jointingprocedures using the AUSPEX Mini Tool but shouldnot be regarded as a substitute for reading andapplying the detailed instructions contained in the tool manual.
1 Ensure that the battery is fully charged and attach it to the tool.
2 Select the jaw size to suit the fitting to be crimped.The jaws must be examined in terms of possibledamage, or dirt in the compression area.
3 To change the jaw push the pin in and at the sametime twist it in an anti-clockwise direction. The pinshould then spring back.
4 Insert the jaws and line up the holes in the tool withthe hole in the jaw.
5 Push the pin through the hole in the jaw until it locksin position.
10_DUOPEX GAS MANUAL
DUOPEX GAS MANUAL_11
6 Cut the pipe to the required length with therecommended multi layer pipe cutters.
7 Clean the pipe by using the deburring tool.
8 Insert the calibrating tool into the pipe, and thenalternately turn in a clockwise and in a counter-clockwise direction.
12_DUOPEX GAS MANUAL
9 Insert the pipe into the fitting and under the stainlesssteel ring and push the pipe until it is visible in theslots of the plastic ring. This ensures you have pushedthe pipe home.
11 With the jaws open place the fitting inside the jaws so that the raised section of the plastic ring fits intothe slot in the jaws. Release the jaws so they fit snuglyover the fitting ensuring that the raised section of theplastic ring fit into the slots in the jaw.
10 By squeezing the back of the jaw the jaws will open. If you look at the machined profile on the inside of thejaws you will note a slot on each side of the profile.
MAKING A JOINT
witnesshole
DUOPEX GAS MANUAL_13
12 Press the switch mechanism until the joint iscompleted and the piston has retracted back into the body of the tool.
13 Press the back end of the jaws and remove thecompleted joint.
14_DUOPEX GAS MANUAL
Pipe and fittings are joined and sealed thanks to thestainless steel outer bush mechanical deformation (2).This deformation is achieved by using the specialDUOPEX GAS jaws.
1 Multi layer pipe
2 Stainless steel clamping bush
3 O-Rings
4 Plastic sight ring
5 DR Brass
1.
Multi layer pipe
2.
Stainless steelclamping bush
3.O-Rings
4.Plastic sight ring whichchecks if the tube has
been correctly installed in thepipe fitting and dielectricallyisolates the tube itself from
pipe fitting core
5.DR Brass
DUOPEX GAS MANUAL_15
SIZING TABLES FOR NATURAL GASN
ATU
RA
L G
AS
Pre
ssur
e d
rop
: 0.0
75kP
a (M
eter
pre
ssur
e 1.
1 kP
a)
F
low
thr
oug
h P
E-X
/ A
L /
PE
-X p
ipe
crim
p f
ittin
gs
(MJ/
h)
Leng
th o
f st
raig
ht p
ipe
in m
etre
s
Nom
Siz
e2
46
810
1214
1618
2025
3035
4045
5055
60C
orre
ctio
n(m
m)
(+ m
t for
fittin
g)16
8359
4841
3734
3129
2826
2321
2019
1717
1615
1.2
2017
012
098
8576
6964
6057
5448
4441
3836
3432
311.
126
261
185
151
131
117
107
9992
8783
7467
6258
5552
5048
0.6
3257
240
533
028
625
623
421
620
219
118
116
214
813
712
812
111
410
910
40.
540
1039
734
600
519
464
424
393
367
346
328
294
268
248
232
219
208
198
190
N/A
5018
9813
4210
9694
984
977
571
767
163
360
053
749
045
442
440
038
036
234
7N
/A63
3558
2516
2054
1779
1591
1452
1345
1258
1186
1125
1006
919
850
795
750
712
678
650
N/A
NAT
UR
AL
GA
SP
ress
ure
dro
p: 0
.75k
Pa
(Met
er p
ress
ure
2.75
kP
a)
F
low
thr
oug
h P
E-X
/ A
L /
PE
-X p
ipe
crim
p f
ittin
gs
(MJ/
h)
Leng
th o
f st
raig
ht p
ipe
in m
etre
s
Nom
Siz
e2
46
810
1214
1618
2025
3035
4045
5055
60C
orre
ctio
n(m
m)
(+ m
t for
fittin
g)16
264
186
152
132
118
108
100
9388
8375
6863
5956
5350
481.
720
541
383
312
271
242
221
204
191
180
171
153
140
129
121
114
108
103
991.
526
831
588
480
416
372
339
314
294
277
263
235
215
199
186
175
166
159
152
0.8
3218
2112
8810
5191
181
474
468
864
460
757
651
547
043
540
738
436
434
733
30.
740
3305
2337
1908
1653
1478
1349
1249
1169
1102
1045
935
853
790
739
697
661
630
603
N/A
5060
4042
7134
8730
2027
0124
6622
8321
3620
1319
1017
0815
6014
4413
5112
7312
0811
5211
03N
/A63
1132
280
0665
3756
6150
6346
2242
7940
0337
7435
8032
0229
2327
0625
3223
8722
4621
5920
67N
/A
SIZING TABLES FOR LPG
16_DUOPEX GAS MANUAL
LPG
SU
PP
LYP
ress
ure
dro
p: 0
.25k
Pa
(Met
er p
ress
ure
2.75
kP
a)
F
low
thr
oug
h P
E-X
/ A
L /
PE
-X p
ipe
crim
p f
ittin
gs
(MJ/
h)
Leng
th o
f st
raig
ht p
ipe
in m
etre
s
Nom
Siz
e2
46
810
1214
1618
2025
3035
4045
5055
60C
orre
ctio
n(m
m)
(+ m
t for
fittin
g)16
355
251
205
177
159
145
134
125
118
112
100
9285
7975
7168
651.
720
728
515
420
364
326
297
275
257
243
230
206
188
174
163
153
146
139
139
1.5
2612
7289
973
463
656
951
948
145
042
440
235
032
830
428
426
825
424
223
20.
832
2450
1733
1415
1225
1096
1000
926
866
817
775
693
633
586
548
517
490
467
447
0.7
4044
4731
4425
6722
2319
8918
1516
8115
7214
8214
0612
5811
4810
6399
493
788
984
881
2N
/A50
8126
5746
4692
4063
3634
3317
3071
2873
2709
2570
2298
2095
1942
1817
1713
1625
1550
1484
N/A
6315
231
1077
087
9476
1668
1262
1657
5753
8550
7748
1743
0839
3335
4134
0632
1130
4629
0527
81N
/A
LPG
SU
PP
LY
Pre
ssur
e d
rop
: 10k
Pa
(Met
er p
ress
ure
70kP
a)
F
low
thr
oug
h P
E-X
/ A
L /
PE
-X p
ipe
crim
p f
ittin
gs
(MJ/
h)
Leng
th o
f st
raig
ht p
ipe
in m
etre
s
Nom
Siz
e2
46
810
1214
1618
2025
3035
4045
5055
60C
orre
ctio
n*(m
m)
(+ m
t for
fittin
g)16
2837
2006
1638
1418
1269
1158
1072
1003
945
897
802
732
878
634
598
567
541
518
2058
2341
1833
5229
1226
0423
7722
0120
5919
4118
4116
4715
0413
9213
0212
2811
6511
1010
5326
1017
271
9358
7350
8645
4941
5938
4535
9733
9132
1728
7726
2724
3222
7521
4520
3419
4018
5732
1960
113
850
1131
798
0187
6680
0274
0969
3065
3461
9855
4450
5146
8643
8341
3239
2037
3835
7940
3557
425
155
2053
917
787
1590
914
523
1344
612
577
1185
811
250
1006
291
8585
0479
5575
0071
1567
8464
9550
6500
945
969
3753
332
505
2907
326
540
2457
122
984
2167
020
558
1838
716
785
1554
014
537
1370
513
002
1239
711
869
6312
1853
8616
370
352
6092
754
491
4974
646
056
4308
240
618
3853
334
465
3146
229
128
2724
725
689
2437
123
235
2224
7*P
leas
e co
ntac
t Aus
pex
Gas
for
corre
ctio
n.
DUOPEX GAS MANUAL_17
DUOPEXGASPRODUCT
LIST
FITTINGS
PIPES
18_DUOPEX GAS MANUAL
PIPE STRAIGHT
16MM X 5M GPM40160520MM X 5M GPM41200526MM X 5M GPM42260532MM X 5M GPM43320540MM X 5M GPM44400550MM X 5M GPM45500563MM X 5M GPM466305
PIPE COILS
16 X 50M GPM40165016 X 100M GPM401610020 X 100M GPM412010026 X 50M GPM42265032 X 50M GPM433250
COUPLINGS
16 GPM011616
20 GPM012020
26 GPM012626
32 GPM013232
40 GPM014040
50 GPM015050
63 GPM016363
20 X 16 GPM022016
26 X 16 GPM022616
26 X 20 GPM022620
32 X 16 GPM023216
32 X 20 GPM023220
32 X 26 GPM023226
40 X 26 GPM024026
40 X 32 GPM024032
50 X 32 GPM025032
50 X 40 GPM025040
63 X 40 GPM026340
63 X 50 GPM026350
FITTINGS
DUOPEX GAS MANUAL_19
TEES
16MM GPM03161616
20MM GPM03202020
26MM GPM03262626
32MM GPM03323232
40MM GPM03404040
50MM GPM03505050
63MM GPM03636363
20 X 16 X 16 GPM04201616
16 X 16 X 20 GPM04161620
20 X 20 X 16 GPM04202016
20 X 16 X 20 GPM04201620
26 X 20 X 16 GPM04262016
26 X 26 X 16 GPM04262616
20 X 20 X 26 GPM04202026
26 X 20 X 20 GPM04262020
26 X 20 X 26 GPM04262026
26 X 26 X 20 GPM04262620
32 X 20 X 20 GPM04322020
32 X 20 X 26 GPM04322026
32 X 20 X 32 GPM04322032
32 X 32 X 20 GPM04323220
32 X 32 X 16 GPM04323216
32 X 26 X 20 GPM04322620
26 X 26 X 32 GPM04262632
32 X 26 X 26 GPM04322626
32 X 26 X 32 GPM04322632
32 X 32 X 26 GPM04323226
32 X 32 X 40 GPM04323240
40 X 40 X 16 GPM04404016
40 X 40 X 20 GPM04404020
40 X 40 X 26 GPM04404026
40 X 40 X 32 GPM04404032
40 X 40 X 50 GPM04404050
40 X 32 X 32 GPM04403232
40 X 32 X 40 GPM04403240
50 X 50 X 20 GPM04505020
50 X 50 X 26 GPM04505026
50 X 40 X 40 GPM04504040
50 X 40 X 50 GPM04504050
50 X 50 X 32 GPM04505032
50 X 50 X 40 GPM04505040
63 X 63 X 26 GPM04636326
63 X 63 X 32 GPM04636332
63 X 63 X 40 GPM04636340
63 X 63 X 50 GPM04636350
FITTINGS
20_DUOPEX GAS MANUAL
THREADED BSP TEES (MALE)
16 X 16 X 1/2" GPM04161615MI
20 X 20 X 1/2" GPM04202015MI
20 X 20 X 3/4" GPM04202020MI
26 X 26 X 1/2" GPM04262615MI
26 X 26 X 3/4" GPM04262620MI
26 X 26 X 1" GPM04262625MI
32 X 32 X 1" GPM04323225MI
40 X 40 X 1 1/4" GPM04404032MI
THREADED BSP TEES (FEMALE)
16 X 16 X 1/2" GPM04161615FI
20 X 20 X 1/2" GPM04202015FI
20 X 20 X 3/4" GPM04202020FI
26 X 26 X 1/2" GPM04262615FI
26 X 26 X 3/4" GPM04262620FI
32 X 32 X 1/2" GPM04323215FI
32 X 32 X 3/4" GPM04323220FI
32 X 32 X 1" GPM04323225FI
40 X 40 X 1" GPM04404025FI
40 X 40 X 1 1/4" GPM04404032FI
50 X 50 X 3/4" GPM04505020FI
50 X 50 X 1" GPM04505025FI
63 X 63 X 1" GPM04636325FI
45° ELBOWS
26 X 26 GPM05452626
32 X 32 GPM05453232
40 X 40 GPM05454040
50 X 50 GPM05455050
63 X 63 GPM05456363
DUOPEX GAS MANUAL_21
ELBOWS
16MM GPM051616
20MM GPM052020
26MM GPM052626
32MM GPM053232
40MM GPM054040
50MM GPM055050
63MM GPM056363
THREADED BSP ELBOWS (FEMALE)
16 X 1/2" GPM051615FI
20 X 1/2" GPM052025FI
20 X 3/4" GPM052020FI
26 X 3/4" GPM052620FI
26 X 1" GPM052625FI
32 X 1" GPM053226FI
40 X 1 1/4" GPM054032FI
50 X 1 1/2" GPM055040FI
THREADED BSP ELBOWS (MALE)
16 X 1/2" GPM051615MI
20 X 1/2" GPM052025MI
20 X 3/4" GPM052020MI
26 X 3/4" GPM052620MI
32 X 1" GPM053225MI
40 X 1 1/4" GPM054032MI
50 X 1 1/2" GPM055040MI
63 X 2" GPM056350MI
FITTINGS
22_DUOPEX GAS MANUAL
LUGGED ELBOWS (FEMALE)
16 X 1/2" GPM061615FI
20 X 1/2" GPM072015
LUGGED ELBOWS (FEMALE) TWO WAY
16 X 1/2" GPM07161615
20 X 1/2" GPM07202015
THREADED BSP ADAPTORS (MALE)
16 X 1/2" GPM091615
16 X 3/4" GPM091620
20 X 1/2" GPM092015
20 X 3/4" GPM092020
26 X 3/4" GPM092620
26 X 1" GPM092625
32 X 1" GPM093225
32 X 1 1/4" GPM093232
40 X 1 1/4" GPM094032
50 X 1 1/2" GPM095040
63 X 2" GPM096350
DUOPEX GAS MANUAL_23
THREADED BSP ADAPTORS (FEMALE)
16 X 1/2" GPM101615
16 X 3/4" GPM101620
20 X 1/2" GPM102015
20 X 3/4" GPM102020
26 X 3/4" GPM102620
26 X 1" GPM102625
32 X 1" GPM103225
32 X 1 1/4" GPM103232
40 X 1 1/4" GPM104032
50 X 1 1/2" GPM105040
END CAPS
16 GPM1416
20 GPM1420
26 GPM1426
32 GPM1432
40 GPM1440
LOOSE NUT CONNECTOR ELBOWS (MALE)
26 X 1" GPM19161590MI
FITTINGS
24_DUOPEX GAS MANUAL
LOOSE NUT CONNECTOR STRAIGHT (MALE)
16 X 1/2" GPM191615MI
16 X 3/4" GPM191620MI
20 X 1/2" GPM192015MI
20 X 3/4" GPM192020MI
LOOSE NUT CONNECTOR STRAIGHT (FEMALE)
16 X 1/2" GPM191615FI
16 X 3/4" GPM191620FI
20 X 1/2" GPM192015FI
20 X 3/4" GPM192020FI26 X 1" GPM192625FI26 X 1 1/4" GPM192632FI
ACCESSORIES
Tool specific for multi layered pipe
CUTTING TOOL DEBURRING TOOL
CALIBRATING TOOL BENDING SPRINGS
DUOPEX GAS MANUAL_25
TOOL KITS
MINI KIT
MAXI KIT
DUOPEX Jaws 40-63mm
DUOPEX Jaws 16-32mm
AUSPEX GAS Pty Ltd ACN 108 491 792
9-11 Sahra Grove Carrum Downs Victoria 3201 AustraliaTelephone (03) 9770 3600 Facsimile (03) 9445 9277
www.duopex.com.auAll statements, information and data given herein are believed to be accurate and reliable but are presentedwithout guarantee or responsibility of any kind, expressed or implied, on our part.