Recircular agua desmineralizada
-
Upload
jose-gonzalez -
Category
Documents
-
view
216 -
download
0
Transcript of Recircular agua desmineralizada
-
7/27/2019 Recircular agua desmineralizada
1/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
GPM .06 to 75(Nominal Rating)
Viking
Mag Drive is designed to provide positivedisplacement pumping capability in those situations tha
require the highest assurance of liquid containment
Viking Mag Drive provides for the safe, trouble-free
transfer of hazardous, EPA-regulated fluids withou
electronic monitoring as required with mechanical face-
type shaft seals. Hard-to-seal liquids are also easily
handled with the Viking Mag Drive which eliminates
the high cost of mechanical seal replacement and
repair. A variety of coupling sizes are available for flow
requirements to 75 GPM. The torque-carrying ability of
high-strength magnets allows pumps to be coupled
with gear reducers for slow-speed handling of viscous
liquids. The self-priming positive-displacement pumpingprinciple provides low-shear, nonpulsating flow. Interna
gear pumps are available in stainless steel, steel, and
cast iron construction. External gear pumps are available
in cast iron or ductile iron construction with heat-
treated steel shafts and gears.
See following pages and performance curves for specific recommendations.
Certain models have lower limitations.
Optional samarium cobalt magnets are used at temperatures over 225F.
Nominal capacities based on handling thin liquids at low pressures.Kalrez- Registered trademark of DuPont Performance Elastomers.
Viton- Registered trademark of DuPont Performance Elastomers.
Viking and Viking Mag Drive- Registered trademarks of Viking Pump, Inc.
Differential
Pressures
To 34 BAR
To 500 PSIExternal Gear
To 8.5 BAR
To 125 PSIInternal Gear
Temperature
Range
-50C. to +260C.
-60F. to +500F.
Viscosity
Range
1.0 cSt. to 55,000 cSt.
28 SSU to 250,000 SSU
FEATURES
INTERNAL GEAR AND SPUR GEAR PUMPSWITH MAGNETIC DRIVE
TemperatureSensor
CasingBushing
BalancePlate Casing
Head
Idler Pin
Head GasketOuter Magnet Assembly
Bearing Carrier Assembly Canister
Shaft
Bracket
Inner Magnet Assembly
Canister O-Ring
RotorIdler
Pressure Relief Valve
SERIES 897 PumpsCutaway View
HL size shown
INTERNAL GEAR
Viking internal gear Mag Drivepumps are available in stainless
steel, steel, or cast iron constructionwith capacities up to 75 GPM. Withonly two moving parts Viking MagDrive and Vikings gear-within-a-gear principle provides low-shearpumping.
MAGNETIC COUPLING
Viking Mag Drive magneticallycouples the pump to the driver.Magnetic force passing through astainless steel canister is used todrive the inner coupling, eliminatingthe need for shaft seals.
EXTERNAL SPUR GEAR
Viking external spur gear Mag Drivepumps are available in cast ironconstruction in capacities from .06to 32 GPM. The Viking Mag Drivecan be used in conjunction with aViking Spur Gear Pump for meteringor low-capacity transfer of toxic orexpensive liquids.
Section 680
Page 680.
Issue D
-
7/27/2019 Recircular agua desmineralizada
2/19
-
7/27/2019 Recircular agua desmineralizada
3/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Viton, Neoprene, PTFE, or Kalrez available.
See page 20 for Selecting the correct Mag Drive coupling.
Higher temperatures can be handled with Samarium Cobalt magnets. See page
20 for torque and temperature limits.
ModelNumbers
PortSize
(NPT)
NominalPumpRating
MagneticCoupling
Availability MaximumTemperature
(StandardConstruction)
MaximumHydrostatic
Pressure
ApproximateShippingWeight
With Valve(Less Power)
ApproximateCoupling Only
Shipping Weight(ready to accept but
less power)
Series
Torque
Inches GPM m/h RPM Ft-Lbs NmDegrees
F.Degrees
C. PSIG bar Lbs KG Lbs KG
SG-80417 0.06 0.013 1800
MD-A
4
9
5.4
12.2 225 107
1000 69
6 2.7
31 14
SG-80418 0.14 0.031 1800
SG-80425 0.18 0.041 1800
SG-80435 0.27 0.061 1800
SG-80450 0.36 0.082 18007 3.2
SG-80470 0.50 0.11 1800
SG-80518 SGN-80518 0.70 0.16 1800
6 2.7SG-80525 SGN-80525 1.0 0.23 1800
SG-80535 SGN-80535 1.4 0.32 1800
SG-80550 SGN-80550 2.0 0.45 18007 3.2
SG-80570 SGN-80570 2.8 0.63 1800SG-80510 SGN-80510 4.0 0.91 1800 8 3.6
SG-80514 SGN-80514 5.6 1.27 1800 9 4.1
SG-80519 SGN-80519 7.6 1.72 1800 10 4.5
SG-80528 SGN-80528 11.2 2.54 1800 11 5.0
SG-80741 SGN-80741 1 4.0 0.91 1800
MD-A
MD-B
4
9
15
40
5.4
12.2
20.3
54.0
1000
400
69
28
15 6.8
SG 80758 SGN 80758 1 5.6 1.27 1800 17 7.7
SG-80782 SGN-80782 1 8.0 1.81 1800 18 8.2
SG-80711 SGN-80711 1 11.2 2.54 1800 19 8.6
SG-80716 SGN-80716 1 16.0 3.63 1800 20 9.1
71 32SG-80722 SGN-80722 1 x 1 22.0 5.00 1800 41 18.6
SG-80732 SGN-80732 1 x 1 32.0 7.27 1800 43 19.5
SPECIFICATIONS SERIES SG-804, SG-805, SG-807CAST IRON - SGN-805, SGN-807DUCTILE IRON
CONSTRUCTION
ModelHead, Casing, Separation
Plate & BracketGears
Heat-TreatedShafts
Case-Hardened
Bearings
O-RingsStandard Options
SG-804, SG-805,
SG-807Iron Steel Steel Carbon Graphite
Needle Bearings
or BronzeBuna-N
SGN-805, SGN-807 Ductile Iron Steel Steel Carbon GraphiteNeedle Bearings
or BronzeBuna-N
SERIES 804, 805, AND 807EXTERNAL SPUR GEAR
CAST IRON WITH MAGNETIC DRIVE
Dimensions for External Gear Mag Drive Pumps - See Pages 680.13
through 680.19.Performance Data for External Gear Mag Drive Pumps - See Pages
341.21 through 341.66.
SERIES SG-805 Pumps
With MD-A Mag Drive Coupling.
Section 680
Page 680.3
Issue F
-
7/27/2019 Recircular agua desmineralizada
4/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.4
Issue CSERIES 893 AND 895STEEL AND CAST IRON CONSTRUCTION
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
For specifications, see page 680.2.
DIMENSIONSSERIES 893STEEL UNMOUNTED PUMPSGGHJHL SIZES
For specifications, see page 680.2.
DIMENSIONSSERIES 895CAST IRON UNMOUNTEDPUMPSGGHJHL SIZES
MODEL NO.
(in)
A B C E G H
GG-893 1in 4.00 4.29 1.12 0.62 0.50
mm 102 108 29 16 13
HJ-893HL-893
1in 4.00 5.44 1.50 0.62 0.50
mm 102 138 38 16 13
MODEL NO.(in)A B C E G H
GG-895 1in 2.75 4.29 1.12 0.62 0.50
mm 70 108 29 16 13
HJ-895HL-895
1in 3.75 5.44 1.50 0.62 0.50
mm 95 138 38 16 13
-
7/27/2019 Recircular agua desmineralizada
5/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.5
Issue CSERIES 897 AND 895STAINLESS STEEL AND CAST IRON CONSTRUCTION
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
MODEL NO.(in)A B C E G H
GG-897 1in 4.00 4.29 1.12 0.62 0.50
mm 102 108 29 16 13
HJ-897HL-897
1in 4.00 5.44 1.50 0.62 0.50
mm 102 138 38 16 13
For specifications, see page 680.2.
DIMENSIONSSERIES 897STAINLESS STEELUNMOUNTED PUMPSGGHJHL SIZES
MODEL NO.(in)A B C E G H J K
GG-895-MD-A_B 1in 2.75 4.29 1.12 0.62 0.50 4.35 15.30
mm 70 108 29 16 13 123 389
HJ-895-MD-A_BHL-895-MD-A_B
1in 3.75 5.44 1.50 0.62 0.50 5.50 16.75
mm 95 138 38 16 13 140 425
For specifications, see page 680.2.
DIMENSIONSSERIES 895(MD-AB DRIVE)GGHJHL SIZES
Series 895 shown. See unmounted pump for port
configuration on Series 893 and 897 pumps.
-
7/27/2019 Recircular agua desmineralizada
6/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.6
Issue CSERIES 895CAST IRON CONSTRUCTION
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
For specifications, see page 680.2.
DIMENSIONSSERIES 895(MD-BB DRIVE)HJHL SIZES
Series 895 shown. See unmounted pump for port
configuration on Series 893 and 897 pumps.
MODEL NO.(in)A B C D E G H J K L M N P R T W
GG-895-MD-A_M 1in 2.75 4.29 3.50 1.12 0.62 0.50 4.85 4.75 3.50 0.62 0.50 6.72 2.75 5.25 0.34
mm 70 108 89 29 16 13 123 121 89 16 16 171 70 133 9
HJ-895-MD-A_M
HL-895-MD-A_M1
in 3.75 5.44 3.50 1.50 0.62 0.50 5.50 4.75 3.50 0.62 0.50 6.72 2.75 5.25 0.34
mm 95 138 159 38 16 13 140 121 89 16 13 171 70 133 9
HJ-895-MD-B_M
HL-895-MD-B_M1
in 3.75 5.44 6.25 1.50 0.62 0.75 6.63 6.50 5.00 0.75 0.50 7.00 2.75 8.44 0.56
mm 95 138 159 38 16 13 164 165 127 19 13 178 70 210 14
For specifications, see page 680.4.
DIMENSIONSSERIES 895
(MD-A AND MD-BM DRIVE)GGHJHL SIZES
Series 895 shown. See unmounted pump for port
configuration on Series 893 and 897 pumps.
-
7/27/2019 Recircular agua desmineralizada
7/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.7
Issue CSERIES 893 AND 895STEEL AND CAST IRON CONSTRUCTION
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
For specifications, see page 680.2.
DIMENSIONSSERIES 893STEEL UNMOUNTEDPUMPSASAKAL SIZES
For specifications, see page 680.2.
DIMENSIONSSERIES 895CAST IRON UNMOUNTEDPUMPSASAKAL SIZES
MODEL NO.(in)A B C E F G H
AS-893AK-893
3in 6.00 7.50 2.00 7.00 1.12 0.75
mm 152 190 51 178 29 19
AL-893 3in 6.00 7.25 2.50 7.00 1.12 0.75
mm 152 184 63 178 29 19
MODEL NO.(in)A B C E F G H
AS-895AK-895
2in 5.00 7.50 2.00 7.00 1.12 0.75
mm 127 190 51 178 29 19
AL-895 3in 5.00 7.25 2.50 7.00 1.12 0.75
mm 127 184 63 178 29 19
-
7/27/2019 Recircular agua desmineralizada
8/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.8
Issue CSERIES 897 AND 895STAINLESS STEEL AND CAST IRON CONSTRUCTION
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
For specifications, see page 680.2.
DIMENSIONSSERIES 897STAINLESS STEELUNMOUNTED PUMPSASAKAL SIZES
MODEL NO.(in)A B C E F G H
AS-897AK-897
3in 6.00 7.50 2.00 7.00 1.12 0.75
mm 152 190 51 178 29 19
AL-897 3in 6.00 7.25 2.50 7.00 1.12 0.75
mm 152 184 63 178 29 19
For specifications, see page 680.2.
DIMENSIONSSERIES 895(MD-B B DRIVE)ASAKAL SIZES
Series 895 shown. See unmounted pump for port
configuration on Series 893 and 897 pumps.
MODEL NO.(in)A B C E F G H J K
AS-895-MD-B_BAK-895-MD-B_B
2in 5.00 7.50 2.00 7.00 1.12 0.75 8.69 23.53
mm 127 190 51 178 29 19 221 598
AL-895-MD-B_B 3in 5.00 7.25 2.50 7.00 1.12 0.75 8.44 23.78
mm 127 184 63 178 29 19 14 604
-
7/27/2019 Recircular agua desmineralizada
9/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.9
Issue C
MODEL NO.
(in)
A B C D E F G H J K L M N P R T W
AS-895-MD-B_MAK-895-MD-B_M
2in 5.00 7.50 6.25 2.00 7.00 1.12 0.75 8.69 6.50 5.00 0.75 0.50 7.00 2.75 8.44 0.56
mm 127 190 159 51 178 29 19 221 165 127 19 13 178 70 214 14
AL-895-MD-B_M 3in 5.00 7.25 6.25 2.50 7.00 1.12 0.75 8.44 6.50 5.00 0.75 0.50 7.00 2.75 8.44 0.56
mm 127 184 159 63 178 29 19 214 165 127 19 13 178 70 214 14
SERIES 895CAST IRON CONSTRUCTION
PERFORMANCE CURVE NOTES
For specifications, see page 680.2.
DIMENSIONSSERIES 895(MD-C80 B DRIVE)ASAKAL SIZES
Series 895 shown. See unmounted pump for port
configuration on Series 893 and 897 pumps.
For specifications, see page 680.2.
DIMENSIONSSERIES 895(MD-BM DRIVE)ASAKAL SIZES
Series 895 shown. See unmounted pump for port
configuration on Series 893 and 897 pumps.
MODEL NO.
(in)
A B C E F G H J K
AS-895-MD-C80-BAK-895-MD-C80-B
2in 5.00 7.50 2.00 7.00 1.12 0.75 8.25 22.83
mm 127 190 51 178 29 19 210 580
AL-895-MD-C80-B 3in 5.00 7.25 2.50 7.00 1.12 0.75 8.00 23.08
mm 127 184 63 178 29 19 203 586
-
7/27/2019 Recircular agua desmineralizada
10/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.0
Issue CSERIES 895CAST IRON CONSTRUCTION
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
MODEL NO.(in)A B C L M
GG-895-MD-A_R 1
in 2.75 8.12 3.73 4.29
mm 70 206 95 108
HJ-895-MD-A_RHL-895-MD-A_R
1in 3.75 8.12 4.88 5.44
mm 95 206 124 138
HJ-895-MD-B_RHL-895-MD-B_R
1in 3.75 10.87 6.00 5.44
mm 95 276 152 138
For specifications, see page 680.2.
DIMENSIONSSERIES 895(MD-A AND MD-BR DRIVE)GGHJHL SIZESA SIZE REDUCER UNITS
Series 895 shown. See unmounted pump for port
configuration on Series 893 and 897 pumps.
-
7/27/2019 Recircular agua desmineralizada
11/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.
Issue CSERIES 895CAST IRON CONSTRUCTION
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
For specifications, see page 680.2.
DIMENSIONSSERIES 895(MD-BR DRIVE)ASAKAL SIZESA SIZE REDUCER UNITS
Series 895 shown. See unmounted pump for port
configuration on Series 893 and 897 pumps.
For specifications, see page 680.2.
DIMENSIONSSERIES 895(MD-BR DRIVE)ASAKAL SIZESB SIZE REDUCER UNITS
Series 895 shown. See unmounted pump for port
configuration on Series 893 and 897 pumps.
-
7/27/2019 Recircular agua desmineralizada
12/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.
Issue C
For specifications, see page 680.2.
DIMENSIONSSERIES 895(MD-C80 R DRIVE)ASAKAL SIZESB SIZE REDUCER UNITS
Series 895 shown. See unmounted pump for port
configuration on Series 893 and 897 pumps.
For specifications, see page 680.2.
DIMENSIONSSERIES 895(MD-C80 D DRIVE)ASAKAL SIZES
Series 895 shown. See unmounted pump for port
configuration on Series 893 and 897 pumps.
SERIES 895CAST IRON CONSTRUCTION
PERFORMANCE CURVE NOTES
-
7/27/2019 Recircular agua desmineralizada
13/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.3
Issue CSERIES SG-804 AND SG-805CAST IRON CONSTRUCTION
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
For specifications, see page 680.3.
DIMENSIONSSERIES SG-804, SG-805AND SGN-805(MD-AB DRIVE)
MODEL NO.
(in)
A
WITH R/V LESS R/V
DDB C E B C E
SG-80417MD-A_B in 2.02 13.71 2.08 2.21 12.71 2.27 0.31
mm 51 348 53 56 323 58 8
SG-80418MD-A_B in 2.02 13.71 2.08 2.21 12.71 2.27 0.31
mm 51 348 53 56 323 58 8
SG-80425MD-A_B in 2.09 13.78 2.15 2.28 12.78 2.34 0.31
mm 53 350 55 58 325 59 8
SG-80435MD-A_B in 2.19 13.88 2.25 2.38 12.88 2.44 0.31
mm 56 352 57 60 327 62 8
SG-80450MD-A_B
in 2.34 14.03 2.40 2.53 13.03 2.59 0.31
mm 59 356 61 64 331 66 8
SG-80470MD-A_B in 2.54 14.23 2.60 2.73 13.23 2.79 0.31
mm 65 361 66 69 336 71 8
SG-80518MD-A_B
SGN-80518MD-A_B
in 2.02 13.71 2.08 2.21 12.71 2.27 0.31
mm 51 348 53 56 323 58 8
SG-80525MD-A_B
SGN-80525MD-A_B
in 2.09 13.78 2.15 2.28 12.78 2.34 0.31
mm 53 350 55 58 325 59 8
SG-80535MD-A_B
SGN-80535MD-A_B
in 2.19 13.88 2.25 2.38 12.88 2.44 0.31
mm 56 352 57 60 327 62 8
SG-80550MD-A_B
SGN-80550MD-A_B
in 2.34 14.03 2.40 2.53 13.03 2.59 0.31
mm 59 356 61 64 331 66 8
SG-80570MD-A_BSGN-80570MD-A_B
in 2.54 14.23 2.60 2.73 13.23 2.79 0.31mm 65 361 66 69 336 71 8
SG-80510MD-A_B
SGN-80510MD-A_B
in 1.84 14.53 1.90 1.84 13.53 1.90 0.31
mm 47 369 48 47 344 48 8
SG-80514MD-A_B
SGN-80514MD-A_B
in 2.04 14.93 2.10 2.04 13.93 2.10 0.19
mm 52 379 53 52 354 53 5
SG-80519MD-A_B
SGN-80519MD-A_B
in 2.29 15.43 2.35 2.29 14.43 2.35 0.19
mm 58 392 60 58 367 60 5
SG-80528MD-A_B
SGN-80528MD-A_B
in 2.04 16.33 2.10 2.04 15.33 2.10 0.19
mm 52 415 53 52 389 53 5
-
7/27/2019 Recircular agua desmineralizada
14/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.4
Issue CSERIES SG-807CAST IRON CONSTRUCTION
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
MODEL NO.
(in) WITH R/V LESS R/V
A B C E B C E
SG-80741MD-A_B
SGN-80741MD-A_B1
in 3.07 15.81 3.13 3.26 14.19 3.32
mm 78 402 80 83 360 84
SG-80758MD-A_B
SGN-80758MD-A_B1
in 3.24 15.98 3.30 3.43 14.36 3.49
mm 82 406 84 87 365 89
SG-80782MD-A_B
SGN-80782MD-A_B1
in 3.48 16.22 3.54 3.67 14.60 3.73
mm 88 412 90 93 371 95
SG-80711MD-A_B
SGN-80711MD-A_B1
in 3.81 16.55 3.87 4.00 14.93 4.06
mm 97 420 98 102 379 103
SG-80716MD-A_B
SGN-80716MD-A_B1
in 4.31 17.05 4.37 4.50 15.43 4.56
mm 109 433 111 114 392 116
SG-80722MD-A_BSGN-80722MD-A_B
1S1D
in 4.25 20.20 4.31 4.44 18.58 4.50
mm 108 513 109 113 472 114
SG-80732MD-A_B
SGN-80732MD-A_B
1S
1D
in 4.75 21.20 4.81 4.94 19.58 4.62
mm 121 538 122 125 497 117
S = Suction Port
D = Discharge Port
For specifications, see page 680.3.
DIMENSIONSSERIES SG-807 AND SGN-807(MD-AB DRIVE)
-
7/27/2019 Recircular agua desmineralizada
15/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.5
Issue C
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
SERIES SG-807CAST IRON CONSTRUCTION
MODEL NO.
(in) WITH R/V LESS R/V
A B C E B C E
SG-80741MD-B_B
SGN-80741MD-B_B1
in 3.07 15.81 3.13 3.26 14.19 3.32
mm 78 402 80 83 360 84
SG-80758MD-B_B
SGN-80758MD-B_B1
in 3.24 15.98 3.30 3.43 14.36 3.49
mm 82 406 84 87 365 89
SG-80782MD-B_B
SGN-80782MD-B_B1
in 3.48 16.22 3.54 3.67 14.60 3.73
mm 88 412 90 93 371 95
SG-80711MD-B_B
SGN-80711MD-B_B1
in 3.81 16.55 3.87 4.00 14.93 4.06
mm 97 420 98 102 379 103
SG-80716MD-B_B
SGN-80716MD-B_B1
in 4.31 17.05 4.37 4.50 15.43 4.56
mm 109 433 111 114 392 116
SG-80722MD-B_BSGN-80722MD-B_B 1S1D
in 3.78 20.20 4.31 4.44 18.58 4.50
mm 108 513 109 113 472 114
SG-80732MD-B_B
SGN-80732MD-B_B
1S
1D
in 4.75 21.20 4.81 4.94 19.58 4.62
mm 121 538 122 125 497 117
S = Suction Port
D = Discharge Port
For specifications, see page 680.3.
DIMENSIONSSERIES SG-807 AND SGN-807(MD-BB DRIVE)
-
7/27/2019 Recircular agua desmineralizada
16/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.6
Issue C
For specifications, see page 680.3.
DIMENSIONSSERIES SG-804, SG-805AND SGN-805(MD-AM DRIVE)
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
SERIES SG-804 AND SG-805CAST IRON CONSTRUCTION
MODEL NO.
(in)
A
WITH R/V LESS R/V
DD
MOTORFRAME
SIZE D E F H MCB C B C
SG-80417MD-A_M in 2.02 9.15 2.21 8.15 0.31
56C
3.50 2.44 1.500.34
SLOT2.56mm 51 232 56 207 8
SG-80418MD-A_M in 2.02 9.15 2.21 8.15 0.31
89 62 38 9 65mm 51 232 56 207 8
SG-80425MD-A_M in 2.09 9.22 2.28 8.22 0.31
mm 53 234 58 209 8
143TC
3.50 2.75 2.00 0.34 2.88SG-80435MD-A_M
in 2.19 9.32 2.38 8.32 0.31
mm 56 237 60 211 8
89 70 51 9 73SG-80450MD-A_M in 2.34 9.47 2.53 8.47 0.31
mm 59 241 60 215 8
SG-80470MD-A_M in 2.54 9.67 2.73 8.67 0.31
145TC
3.50 2.75 2.50 0.34 2.88mm 65 246 69 220 8
SG-80518MD-A_MSGN-80518MD-A_M
in 2.02 9.15 2.21 8.15 0.31
89 70 64 9 73mm 51 232 56 207 8
SG-80525MD-A_MSGN-80525MD-A_M
in 2.09 9.22 2.28 8.22 0.31
mm 53 234 58 209 8
182TC
4.50 3.75 2.25 0.41 3.62SG-80535MD-A_MSGN-80535MD-A_M
in 2.19 9.32 2.38 8.32 0.31
mm 56 237 60 211 8
114 95 57 10 92SG-80550MD-A_MSGN-80550MD-A_M
in 2.34 9.47 2.53 8.47 0.31
mm 59 241 64 215 8
SG-80570MD-A_M
SGN-80570MD-A_M
in 2.54 9.67 2.73 8.67 0.31
184TC
4.50 3.75 2.75 0.41 3.62mm 65 246 69 220 8
SG-80510MD-A_MSGN-80510MD-A_M
in 1.84 9.97 1.84 8.97 0.31
114 95 70 10 92mm 47 253 47 228 8
SG-80514MD-A_MSGN-80514MD-A_M
in 2.04 10.37 2.04 9.37 0.19
mm 52 263 52 238 5
213TC*
5.25 4.25 2.75 0.41 4.5SG-80519MD-A_MSGN-80519MD-A_M
in 2.29 10.87 2.29 9.87 0.19
mm 58 276 58 251 5
133 108 70 10 114SG-80528MD-A_MSGN-80528MD-A_M
in 2.04 11.77 2.04 10.77 0.19
mm 52 299 52 274 5
* Motor shaft must be modified to resemble 182TC-184TC shaft length, diameter and key.
-
7/27/2019 Recircular agua desmineralizada
17/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
Section 680
Page 680.7
Issue C
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
SERIES SG-807CAST IRON CONSTRUCTION
MODEL NO.
(in)
A
WITH R/V LESS R/V MOTORFRAME
SIZE D E F H MCB C B C
SG-80741MD-A_MSGN-80741MD-A_M
1in 3.07 11.25 3.26 9.63
56C3.50 2.44 1.50 0.34 SLOT 2.56
mm 78 286 83 245 89 62 38 9 65SG-80758MD-A_M
SGN-80758MD-A_M1
in 3.24 11.42 3.43 9.80
143TC3.50 2.75 2.00 0.34 2.88
mm 82 290 87 24989 70 51 9 73
SG-80782MD-A_MSGN-80782MD-A_M
1in 3.48 11.66 3.67 10.04
145TC3.50 2.75 2.50 0.34 2.88mm 88 296 93 25589 70 64 9 73SG-80711MD-A_M
SGN-80711MD-A_M1
in 3.81 11.99 4.00 10.37
mm 97 305 102 263182TC
4.50 3.75 2.25 0.41 3.62
SG-80716MD-A_M
SGN-80716MD-A_M
1in 4.31 12.49 4.50 10.87 114 95 57 10 92
mm 109 317 114 276184TC
4.50 3.75 2.75 0.41 3.62SG-80722MD-A_M
SGN-80722MD-A_M1S1D
in 4.25 15.64 4.25 15.02114 85 70 10 92
mm 108 397 108 356
213TC*5.25 4.25 2.75 0.41 4.50SG-80732MD-A_M
SGN-80732MD-A_M1S1D
in 4.75 16.64 4.75 15.02133 108 70 10 114mm 121 423 121 382
* Motor shaft must be modified to resemble 182TC-184TC shaft length, diameter and key.
For specifications, see page 680.3.
DIMENSIONSSERIES SG-807 AND SGN-807(MD-AM DRIVE)
-
7/27/2019 Recircular agua desmineralizada
18/19VIKING PUMPA Unit of IDEX Corporation Cedar Falls, IA 2008
SERIES SG-807CAST IRON CONSTRUCTION
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
MODEL NO.
(in)
A
WITH R/V LESS R/V
B C E B C E
SG-80741MD-A_MSGN-80741MD-A_M
1in 3.07 11.25 3.13 3.26 9.63 3.32
mm 78 286 80 83 245 84
SG-80758MD-A_MSGN-80758MD-A_M
1in 3.24 11.42 3.30 3.43 9.80 3.49
mm 82 290 84 87 249 89
SG-80782MD-A_MSGN-80782MD-A_M
1in 3.48 11.66 3.54 3.67 10.04 3.73
mm 88 269 90 93 255 95
SG-80711MD-A_MSGN-80711MD-A_M 1in 3.81 11.99 3.87 4.00 10.37 4.06
mm 97 305 98 102 263 103
SG-80716MD-A_MSGN-80716MD-A_M
1in 4.31 12.49 4.37 4.50 10.87 4.56
mm 109 317 111 114 276 116
SG-80722MD-A_MSGN-80722MD-A_M
1S1D
in 4.25 15.64 4.31 4.25 14.02 4.31
mm 108 397 109 108 356 109
SG-80732MD-A_MSGN-80732MD-A_M
1S1D
in 4.75 16.64 4.81 4.75 15.02 4.81
mm 121 423 122 121 382 122
S = Suction Port
D = Discharge Port
For specifications, see page 680.3.
DIMENSIONSSERIES SG-807 AND SGN-807MD-AM DRIVE(FOOTED BRACKET)
Footed bracket is only available for up to 145TC framemotors (4.5 rabbet) - 180TC and 210TC motor frameswith 8.5 rabbet are only available with footless bracket,see page 680.17
Section 680
Page 680.8
Issue D
-
7/27/2019 Recircular agua desmineralizada
19/19
DIMENSIONSThese dimensions are average and not for construction purposes. Cert ified prints on request.
SERIES SG-807CAST IRON CONSTRUCTION
MODEL NO.
(in)
A
WITH R/V LESS R/V
B C E B C E
SG-80741MD-B_MSGN-80741MD-B_M
1in 2.60 13.97 3.79 2.80 12.35 3.98
mm 66 355 96 71 314 101
SG-80758MD-B_MSGN-80758MD-B_M
1in 2.77 14.14 3.96 2.97 12.52 4.15
mm 70 359 101 75 318 105
SG-80782MD-B_MSGN-80782MD-B_M
1in 3.01 14.38 4.20 3.21 12.76 4.39
mm 76 365 107 82 324 112
SG-80711MD-B_MSGN-80711MD-B_M
1in 3.34 14.17 4.53 3.54 13.09 4.72
mm 85 374 115 90 332 120
SG-80716MD-B_MSGN-80716MD-B_M
1in 3.84 15.20 5.03 4.04 13.59 5.22
mm 98 386 128 103 345 133
SG-80722MD-B_MSGN-80722MD-B_M
1S1D
in 3.78 18.35 4.97 3.78 16.73 4.97
mm 96 466 126 96 425 126
SG-80732MD-B_MSGN-80732MD-B_M
1S1D
in 4.28 19.35 5.47 4.28 17.73 5.47
mm 109 491 139 109 450 139
S = Suction PortD = Discharge Port
For specifications, see page 680.5.
DIMENSIONSSERIES SG-807 AND SGN-807MD-BM DRIVE
Coupling will accept motor frames 182TC-256TC.254TC-256TC will require shaft modification reducingshaft extension by .
Section 680
Page 680.8.
Issue C