Simulation of Circulating Fluized Bed Reactors Using Aspen Plus
Reactors model aspen plus
-
Upload
ejal-mahrit -
Category
Documents
-
view
140 -
download
4
description
Transcript of Reactors model aspen plus
Introduction to Aspen Plus Reactor Models
Aspen Technology, Inc.6 – 1© 2003 AspenTech. All Rights Reserved.
©2003 AspenTech. All Rights Reserved.
Reactor Models
Introduction to Aspen Plus
©2003 AspenTech. All Rights Reserved.
Lesson Objectives
• Introduce the various classes of reactor models available
• Examine in some detail at least one reactor from each class
Aspen Plus ReferencesUnit Operation Models Reference Manual, Chapter 5, Reactors
Introduction to Aspen Plus Reactor Models
Aspen Technology, Inc.6 – 2© 2003 AspenTech. All Rights Reserved.
©2003 AspenTech. All Rights Reserved.
Reactor Overview
Reactors
Balance BasedRYieldRStoic
Equilibrium BasedREquilRGibbs
Kinetics BasedRCSTRRPlugRBatch
©2003 AspenTech. All Rights Reserved.
Balanced Based Reactors (1)
• RYield– Requires a mass balance only, not an atom balance– Is used to simulate reactors in which inlets to the reactor are
not completely known but outlets are known (e.g., to simulate a furnace)
70 lb/hr H2O20 lb/hr CO2
60 lb/hr CO250 lb/hr tar600 lb/hr char
1000 lb/hr Coal
IN
OUT
RYield
Introduction to Aspen Plus Reactor Models
Aspen Technology, Inc.6 – 3© 2003 AspenTech. All Rights Reserved.
©2003 AspenTech. All Rights Reserved.
Balanced Based Reactors (2)
• RStoic– Requires both an atom and a mass balance– Used in situations where both the equilibrium data and the
kinetics are either unknown or unimportant– Can specify or calculate heat of reaction at a reference
temperature and pressure
2 CO + O2→ 2 CO2
C + O2→ CO2
2 C + O2→ 2 CO
C, O2
IN
OUT
RStoic
C, O2, CO, CO2
©2003 AspenTech. All Rights Reserved.
Equilibrium Based Reactors (1)
• These reactors:– Do not take reaction kinetics into account– Solve similar problems, but specifications are different– Allow individual reactions to be at a restricted equilibrium
• REquil– Computes combined chemical and phase equilibrium by
solving reaction equilibrium equations– Cannot do a three-phase flash– Useful when there are many components, a few known
reactions, and when relatively few components take part in the reactions
Introduction to Aspen Plus Reactor Models
Aspen Technology, Inc.6 – 4© 2003 AspenTech. All Rights Reserved.
©2003 AspenTech. All Rights Reserved.
Equilibrium Based Reactors (2)
• RGibbs
– Useful when reactions occurring are not known or are high in number due to many components participating in the reactions.
– A Gibbs free energy minimization is done to determine the product composition at which the Gibbs free energy of the products is at a minimum.
– This is the only Aspen Plus block that will deal with solid-liquid-gas phase equilibrium.
©2003 AspenTech. All Rights Reserved.
Kinetic Reactors (1)
• Kinetic reactors are RCSTR, RPlug and RBatch.
• Reaction kinetics are taken into account, and hence must be specified.
• Kinetics can be specified using one of the following built-in models, or with a user subroutine:– Power Law– Langmuir-Hinshelwood-Hougen-Watson (LHHW)
• A catalyst for a reaction can have a reaction coefficient of zero.
• Reactions are specified using a Reaction ID.
Introduction to Aspen Plus Reactor Models
Aspen Technology, Inc.6 – 5© 2003 AspenTech. All Rights Reserved.
©2003 AspenTech. All Rights Reserved.
Kinetic Reactors (2)
• RCSTR– Use when reaction kinetics are known and when the reactor
contents have same properties as outlet stream
– Allows for any number of feeds, which are mixed internally– Up to three product streams are allowed – vapor, liquid1,
liquid2 or vapor, liquid, free water– Will calculate duty given temperature or temperature given duty– Can model equilibrium reactions simultaneously with rate-
based reactions
©2003 AspenTech. All Rights Reserved.
Kinetic Reactors (3)
• RPlug– Handles only rate-based reactions– A cooling stream is allowed– You must provide reactor length and diameter
• RBatch– Handles rate-based kinetics reactions only– Any number of continuous or delayed feeds are allowed– Must provide one of the following: stop criteria, cycle time, or
result time– Holding tanks are used to interface with steady-state streams
of Aspen Plus
Introduction to Aspen Plus Reactor Models
Aspen Technology, Inc.6 – 6© 2003 AspenTech. All Rights Reserved.
©2003 AspenTech. All Rights Reserved.
Using a Reaction ID
• Reaction IDs are setup as objects, separate from the reactor, and then referenced within the reactor(s).
• A single Reaction ID can be referenced in any number of kinetic reactors (RCSTR, RPlug and RBatch).
• To set up a Reaction ID, go to the Reactions ReactionsObject Manager.
©2003 AspenTech. All Rights Reserved.
Power-Law Rate Expression
[ ] iexponenti
iionconcentratkrate ∏×=
( )
−−
=
00
11R
Energy ActivationexpFactor lexponentia-Pre
TTTT
kn
( )
−×=
RTEnergy Activation
expFactor lexponentia-Pre nTk
If reference temperature, T0, is not specifed, k is expressed as:
Introduction to Aspen Plus Reactor Models
Aspen Technology, Inc.6 – 7© 2003 AspenTech. All Rights Reserved.
©2003 AspenTech. All Rights Reserved.
Power-Law Rate Expression Example
2 3 21
2A B C D
k
k+ →
← +
Forward reaction: (Assuming the reaction is 2nd order in A)
coefficients: A: B: C: D: exponents: A: B: C: D:
Reverse reaction: (Assuming the reaction is 1st order in C and D)
coefficients: C: D: A: B: exponents: C: D: A: B:
©2003 AspenTech. All Rights Reserved.
Heats of Reaction
• Heats of reaction need not be provided for reactions.
• Heats of reaction are typically calculated as the difference between inlet and outlet enthalpies for the reactor (see Appendix A).
• If you have a heat of reaction value that does not match the value calculated by Aspen Plus, you can adjust the heats of formation (DHFORM) of one or more components to make the heats of reaction match.
• Heats of reaction can also be calculated or specified at a reference temperature and pressure in an RStoic reactor.
Introduction to Aspen Plus Reactor Models
Aspen Technology, Inc.6 – 8© 2003 AspenTech. All Rights Reserved.
©2003 AspenTech. All Rights Reserved.
Filename: REACTORS.BKP
Use the NRTL-HOC property method
Reactor Workshop (1)
• Objective: Compare the use of different reactor types to model one reaction.
Temp = 70°CPres = 1 atm
Feed:
Water: 8.892 kmol/hrEthanol: 186.59 kmol/hrAcetic Acid: 192.6 kmol/hr
Length = 2 m
Diameter = 0.3 m
Volume = 0.14 m3
70% conversion of ethanol
RSTOIC
F-STOIC P-STOIC
RGIBBS
F-GIBBS P-GIBBS
RPLUGF-PLUG P-PLUG
DUPL
FEED
F-CSTR
RCSTR
P-CSTR
©2003 AspenTech. All Rights Reserved.
Reactor Workshop (2)
• Reactor Conditions: Temperature = 70°C, Pressure = 1 atm
• Stoichiometry: Ethanol + Acetic Acid ↔ Ethyl Acetate + Water
• Kinetic Parameters:– Reactions are first order with respect to each of the reactants
in the reaction (second order overall).– Forward Reaction: k = 1.9 x 108, E = 5.95 x 107 J/kmol– Reverse Reaction: k = 5.0 x 107, E = 5.95 x 107 J/kmol– Reactions occur in the liquid phase.– Composition basis is Molarity.
Hint: Check that each reactor is considering both Vapor and Liquid as Valid phases.