ESS 315 – Tiffany Litz. Will lead to loss of $$$s. Can lead to loss of lives. Avoidable messes.
RCP6 ROBO Cylinder® RCP6 S -RRA7R - Intelligent …S)-RRA7R_p...RCP6(S)-RRA7R Vertical mount Speed...
Transcript of RCP6 ROBO Cylinder® RCP6 S -RRA7R - Intelligent …S)-RRA7R_p...RCP6(S)-RRA7R Vertical mount Speed...
RCP6 ROBO Cylinder®RCP6 ROBO Cylinder®
n Model Specification Items
RRA7R WA 56PSeries Type Encoder Type Motor Type Lead Stroke Applicable
Controller/I/O Type Cable Length Options
RCP6: Separate ControllerRCP6S: Built-in Controller
WA: Battery-less Absolute
56P: Stepper Motor 56¨ Size
24: 24mm 16: 16mm 8: 8mm 4: 4mm
70: 70mm
~
520: 520mm(50mm
increments)
[RCP6]P3: PCON
MCON MSEL
[RCP6S]SE: SIO Type
N : NoneP : 1mS : 3mM : 5mX¨¨ : Specified LengthR¨¨ : Robot Cable
Please refer to the options table below.*Please make sure to specify either ML or MR when ordering the side-mounted motor type.
RCP6 (S )-RRA7R
* RCP6 does not include a controller. RCP6S includes a built-in controller.* Please refer to P.11 for more information about the model specification items.
¢ Correlation Diagrams of Speed and Payload
0 100 200 300 400 500 600 700 800 900 10000
102030405060708090
100
0 100 200 300 400 500 600 700 800 900 10000
5
10
15
20
25
30
RCP6(S)-RRA7R Horizontal mount
High-output enabled with PCON/MCON/MSEL connected.
Payl
oad
(kg)
RCP6(S)-RRA7R Vertical mount
Speed (mm/s)
Lead 16Lead 16Lead 24Lead 24
Lead 4Lead 4
Lead 8Lead 8
332255
Lead 8 assumes operation at 0.1G, the other leads assume operation at 0.3G.
Lead 4 assumes operation at 0.1G, the other leads assume operation at 0.3G.
Payl
oad
(kg)
Speed (mm/s)
Lead 16Lead 16Lead 24Lead 24
Lead 4Lead 4
Lead 8Lead 8
3333 11 11
73 RCP6(S)-RRA7R
(Unit: mm/s)
Actuator Specifications¢ Lead and Payload ¢ Stroke and Max. Speed
Model Number Lead (mm)
Connected Controller
Max. Payload Stroke (mm)Horizontal (kg) Vertical (kg)
RCP6(S)-RRA7R-WA-56P-24-�-�-�-� 24 High-output Enabled 20 3
70~520 (The increment
of stroke is 50mm)
RCP6(S)-RRA7R-WA-56P-16-�-�-�-� 16 High-output Enabled 50 8
RCP6(S)-RRA7R-WA-56P-8-�-�-�-� 8 High-output Enabled 60 18
RCP6(S)-RRA7R-WA-56P-4-�-�-�-� 4 High-output Enabled 80 28
Lead (mm)
Connected Controller
70~520 (Every 50mm)
24 High-output Enabled
860 <640>
16 High-output Enabled 560
8 High-output Enabled
420 <350>
4 High-output Enabled 175
Values in brackets < > are for vertical use.
� Cable Length� Stroke
Actuator SpecificationsItem Description
Drive system Ball screw f12mm, rolled C10Positioning repeatability ±0.01mmLost motion 0.1mm or lessRod f30mm AluminumRod non-rotation precision* 0 deg.Allowable load and torque on rod tip See P. 127Rod tip overhang distance 150mmAmbient operating temp. & humidity 0~40°C, 85% RH or less (Non-condensing)
* Rod's angular displacement in rotational direction with no load applied to the rod.
� Options
Name Option Code Reference PageBrake B See P.105Cable exit direction (Outside) CJO See P.105Flange FL See P.106Tip adapter (Flange) FFA See P.105Tip adapter (Internal thread) NFA See P.109Tip adapter (Keyway) KFA See P.108Motor side-mounted to the left ML See P.109Motor side-mounted to the right MR See P.109Knuckle joint* NJ See P.110Non-motor end specification NM See P.110Clevis bracket* QR See P.111
* The clevis (QR) and knuckle joint (NJ) are sold as a set. The assembly is to be performed by the customer.# When selecting multiple options, please list them in alphabetical order. (e.g.
B-CJB-NM)
Legend: � Stroke � Applicable controller/I/O type � Cable length � Options
Stroke (mm) RCP6 RCP6S Stroke (mm) RCP6 RCP6S70 � � 320 � �
120 � � 370 � �
170 � � 420 � �
220 � � 470 � �
270 � � 520 � �
Cable Type Cable Code RCP6 RCP6S
StandardP (1m) � �S (3m) � �M (5m) � �
Specified LengthX06 (6m) ~X10 (10m) � �X11 (11m) ~X15 (15m) � �X16 (16m) ~X20 (20m) � �
Robot Cable
R01 (1m) ~R03 (3m) � �R04 (4m) ~R05 (5m) � �R06 (6m) ~R10 (10m) � �R11 (11m) ~R15 (15m) � �R16 (16m) ~R20 (20m) � �
* Please refer to P.144 for more information regarding the maintenance cables.
*Depending on the model, there may be some limitations to using the vertical, side, and ceiling mount positions. Please contact IAI for more information regarding mounting positions.
The figure above is the motor side-mounted to the left (ML).
P
O I N T
SelectionNotes
(1) The maximum acceleration/deceleration is 1G for horizontal, and 0.5G for vertical use.(2) The actuator specification displays the payload's maximum value, but it will vary depending on the acceleration and speed.
Please refer to the "Selection Guidelines" (RCP6 Tables of Payload by Speed/Acceleration) on P.115 for more details.(3) The radial cylinder is equipped with a built-in guide. Please refer to the graphs shown in P.127 and after for the allowable
load mass.(4) When performing push-motion operation, please confirm the push force of each model by checking the "Correlation
diagram of push force and current limit" on P.113.(5) Depending on the ambient operational temperature, duty control is necessary for the RCP6S (built-in controller type) with
lead 4/8/16. Please refer to P.130 for more information.
Side-mounted Motor
24 VStepper Motor
Motor Unit Type
Body Width
70* mm
Battery-less
Absolute
Radial Load OK
Horizontal
Side
Vert
ical
Ceiling
* Body width does not include the width of the side-mounted motor.
(Note 1) The payload assumes that there is an external guide.
RCP6 ROBO Cylinder®
(85.2) 164.7
51 (Motor side-mounted to the left)20 (Motor side-mounted to the right)
M3 depth 4 (For ground line)
3Stroke
3
249.9 (same as the type with brake)Must be 100 or more
31
12
32.5L
A54
2
27.5 (e�ective threaded portion)
30.59.5 (Width across �ats)
14
φ30 (Ro
d oute
r diam
eter)
φ35
h7
M14×1.5Grease nippleM.E.HomeS.E.M.E.
28 B45G×100P
30D×100P 80K (φ4 hole - φ4 hole)
H-φ6, φ9.5 deep counterbored, depth 5.5 (From back side)
E-M5 through (Bolt screw-in depth: 10)M-φ4 H7 depth 6
(From mounting surface)
J (φ4 hole - oblong hole)
403731
N-oblong hole depth 6 (From mounting surface)
55
558
4-M8 depth 16
26.551.56870
35.559
(10.
5)
69.5
1.5
35.5
72(1)19.3
143
P.C.D.4645°
4-M8 depth 16, 90° equipartition
19 (Width across �ats)
19 (Width across �ats)
Reference surface (B dimensions range)
The orientation of the width across �ats is indeterminable (*2)
4
(R2) 5
5.5
5.5
5.3
(1)
φ6φ9.5
Reference surface
35.5
Cable exit direction (Option) 15.2
22
(25.
4)
M14×1.5
8
P
+0.0
100
CJOOutside
Detail view of P
Supplied hex nut
Details of base mounting holes
RCP6S-RRA7R
CJOOutside
201.7 51 (Motor side-mounted to the left)20 (Motor side-mounted to the right)
M3 depth 4 (For ground line)
(85.2)244.8
35.5
Status LEDTeaching port
286.9 (same as the type with brake)Must be 100 or more
55
558
4-M8 depth 16
35.5
Cable exit direction (Option)16
* The �gure above is the motor side-mounted to the left (ML).
* The �gure above is the motor side-mounted to the left (ML).
143
RCP6(S)-RRA7R 74
¢ Dimensions and Mass by StrokeStroke 70 120 170 220 270 320 370 420 470 520
L 279.5 329.5 379.5 429.5 479.5 529.5 579.5 629.5 679.5 729.5A 247 297 347 397 447 497 547 597 647 697B 188 238 288 338 388 438 488 538 588 638D 0 1 1 2 2 3 3 4 4 5E 4 6 6 8 8 10 10 12 12 14G 1 1 2 2 3 3 4 4 5 5H 4 4 6 6 8 8 10 10 12 12J 0 85 85 185 185 285 285 385 385 485K 0 0 100 200 200 300 300 400 400 500M 2 2 3 3 3 3 3 3 3 3N 0 1 1 1 1 1 1 1 1 1
Allowable static load on rod tip (N) 175 147 126 111 98.6 88.7 80.6 73.8 68 63Allowable dynamic load on rod tip (kg)
Load offset 0mm 7.7 6.4 5.4 4.7 4.1 3.7 3.3 3.0 2.7 2.5Load offset 100mm 5.1 4.6 4.1 3.7 3.4 3.1 2.8 2.6 2.4 2.2
Allowable static torque on rod tip (N•m) 17.6 14.7 12.7 11.2 9.9 9.0 8.2 7.5 6.94 6.45Allowable dynamic torque on rod tip (N•m) 5.0 4.5 4.0 3.6 3.3 3.0 2.8 2.5 2.32 2.16
Mass (kg)
RCP6 w/o brake 4.6 4.9 5.2 5.5 5.7 6.0 6.3 6.6 6.8 7.1w/ brake 4.8 5.0 5.3 5.6 5.9 6.1 6.4 6.7 7.0 7.2
RCP6S w/o brake 4.8 5.0 5.3 5.6 5.9 6.1 6.4 6.7 7.0 7.2w/ brake 4.9 5.1 5.4 5.7 6.0 6.2 6.5 6.8 7.1 7.3
Dimensions
*1 When the rod is returning to its home position, please be careful of interference from surrounding objects, as it will travel until it reaches the M.E. M.E: Mechanical end S.E: Stroke end
*2 The direction of width across flats varies depending on the product.*3 When fixing the actuator using a front bracket or flange, please make sure that there is no external force applied to the main body.
¢ Rod Deflection of RCP6(S)-RRA7R (Reference Values)
Load on rod tip (N)
De�
ectio
n (m
m)
Home70st120st170st220st270st320st370st420st470st520st
0 10 20 30 40 50 60 70 80 90 1000.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
� Applicable ControllersThe RCP6 series actuators can be operated by the controllers indicated below. Please select the type depending on your intended use. * Please refer to P.147 for more information about the built-in controller of RCP6S series.
*Please select "high-output specification" as an option for the MCON. With the MCON, operation is possible only when the high-output specification is selected.
NameExternal
viewMax. number of controlled axes
Input power Control method Maximum number of positioning points
Reference pagePositioner Pulse train Program Network *Option
PCON-CB/CGB 1
DC24V
�*Option
�*Option
-
Note: · The type of compatible networks will vary depending on the controller. Please refer to reference page for more information.
512(768 for network spec.)
Please see P.131
MCON-C/CG 4This model is
network-compatible only.256
Please see the MCON catalog.
MSEL-PC/PG 4Single-phase 100~230VAC
- - � 30,000Please see the MSEL-
PC/PG catalog.
CAD drawings can be downloaded from our website.
www.intelligentactuator.com2D
CAD2D
CAD