Rama Iyer Marine & Offshore division Mechanical Drives · Slide 2 General information – marine...
Transcript of Rama Iyer Marine & Offshore division Mechanical Drives · Slide 2 General information – marine...
OTC 2010 X-pert Center
Jack-up and Marine Propulsion Gearbox/ Rig Solutions
Rama Iyer Marine & Offshore division Mechanical Drives
Copyright © Siemens AG 2010. All rights reserved
Copyright © Siemens AG 2010. All rights reservedSlide 2
General information – marine gearboxes
Power ranges from 1200 HP to 60,000 HP and above
Transmission ratios from 1.5 to 12.1
Propeller thrust bearings are built into the gearbox
One motor or one engine drive
Twin motor or twin engine drive
Generator gearboxes
Gearboxes for Dredgers
Customized solutions
One stop shop for motors, gearboxes, couplings and control systems
Copyright © Siemens AG 2010. All rights reservedSlide 3
General information – marine gearboxes Single input / Single output gearbox
Vertical, horizontal or diagonally offset shafts.
PTO (Power Take Off) is provided to generate
Inexpensive on-board current. PTH option also available.
As standard, all gearboxes are equipped with an oil supply and monitoring system
Power rating from 1,000 to 30,000 kW
Ratio from 1.5 to 12:1.
The propeller shaft thrust bearings are fitted into the gearbox.
Housings of torsionally rigid design, which also ensures perfect meshing of the gear teeth under any condition
Copyright © Siemens AG 2010. All rights reservedSlide 4
General information – marine gearboxes Twin input / Single output gearbox
Primary PTO’s are provided, i.e. the multiple disk
Clutches which are fitted for connecting or
Disconnecting an engine
Design with primary or secondary PTO
Quillshaft design at more than 10,000 kW
Two-speed PTO’s can be used to achieve higher
Propulsion flexibility.
Power rating from 1,000 to 45,000 kW
Ratio from 2 to 6:1
Copyright © Siemens AG 2010. All rights reservedSlide 5
General information – marine gearboxes Generator drive gearbox
Generator gearboxes for the generation of inexpensive on-board current are built as separate gearboxes in connection with low-speed diesel engines, and are arranged in the propeller shaft line or on the main engine face.
Two-speed generator gearboxes for PTO/PTI operation also available.
Power range up to 10,000 kW
Copyright © Siemens AG 2010. All rights reservedSlide 6
General information – marine gearboxes G-series gearbox for dredging applications
For the different dredger types like hopper suction dredgers, suction-cutter dredgers, etc., gearboxes available for:
propeller drives
cutter head drives
suction press pump drives
jet pump drives
generator drives
Copyright © Siemens AG 2010. All rights reservedSlide 7
Drives for other marine equipments
Gearboxes also available for
Sand Pumps
Dredging applications (Cutterhead drives)
Hoists
Winches
Cranes
Bevel gear sets for Thrusters
Copyright © Siemens AG 2010. All rights reservedSlide 9
Typical layout of jacking drives
440 KIPS
6x3=18 per leg
Total 54 per rig
550 KIPS
6x3=18 per leg
Total=54 per rig
1000 KIPS
4x3=12 per leg
Total=36 per rig
Copyright © Siemens AG 2010. All rights reservedSlide 10
Gearbox features
Jacking Torque rating from 1,000,000 in-lbs to over 25,000,000 in-lbs
Hardened and ground gears
Special ratios for specific applications
Input configuration and output pinion customization
Rugged construction for marine application
Copyright © Siemens AG 2010. All rights reservedSlide 12
PLANUREX® P2PA 21 compact drive system on both sides of the Rack
Gear units for jack-up systems
Copyright © Siemens AG 2010. All rights reservedSlide 13
Scope of supply
Gearbox
Output Pinion
Coupling
Motor
Control System
Jack case (if requested by customer)
Copyright © Siemens AG 2010. All rights reservedSlide 15
...powered by Siemens Marine
Full speed ahead