RAM® HandStand™Assembly Guide - rammount.com · RPR-INS-GDS-HS1 RAM® HandStand™Assembly Guide...

2
RPR-INS-GDS-HS1 RAM® HandStand™Assembly Guide 1. Shift hand strap to the side to expose screw head. Loosen screw with screwdriver to disassemble: 2. Insert Nut into center nut pocket of Slip Washer. White nylon inside Nut must be facing upward. 3. Insert Slip Washer with Nut into center hole of your IntelliSkin™. 4. While holding Nut in place, reassemble the RAM® HandStand™ from the outside of your IntelliSkin™, fully tightening down on the screw. For a video demonstration of this assembly, visit www.rammount.com/part/RAM-GDS-HS1U The RAM® HandStand is compatible with any IntelliSkin™ that features the unique circular interface on the back. Nut Slip Washer HandStand™ RPR-INS-GDS-HS1 RAM® HandStand™Assembly Guide 1. Shift hand strap to the side to expose screw head. Loosen screw with screwdriver to disassemble: 2. Insert Nut into center nut pocket of Slip Washer. White nylon inside Nut must be facing upward. 3. Insert Slip Washer with Nut into center hole of your IntelliSkin™. 4. While holding Nut in place, reassemble the RAM® HandStand™ from the outside of your IntelliSkin™, fully tightening down on the screw. For a video demonstration of this assembly, visit www.rammount.com/part/RAM-GDS-HS1U The RAM® HandStand is compatible with any IntelliSkin™ that features the unique circular interface on the back. Nut Slip Washer HandStand™

Transcript of RAM® HandStand™Assembly Guide - rammount.com · RPR-INS-GDS-HS1 RAM® HandStand™Assembly Guide...

Page 1: RAM® HandStand™Assembly Guide - rammount.com · RPR-INS-GDS-HS1 RAM® HandStand™Assembly Guide 1. Shift hand strap to the side to expose screw head. Loosen screw with screwdriver

RPR-INS-GDS-HS1

RAM® HandStand™Assembly Guide

1. Shift hand strap to the side to expose screw head. Loosen screw with screwdriver to disassemble:

2. Insert Nut into center nut pocket of Slip Washer. White nylon inside Nut must be facing upward.

3. Insert Slip Washer with Nut into center hole of your IntelliSkin™.

4. While holding Nut in place, reassemble the RAM® HandStand™ from the outside of your IntelliSkin™, fully tightening down on the screw.

For a video demonstration of this assembly, visit www.rammount.com/part/RAM-GDS-HS1U

The RAM® HandStand is compatible with any IntelliSkin™ that features the unique circular interface on the back.

Nut Slip Washer HandStand™

RPR-INS-GDS-HS1

RAM® HandStand™Assembly Guide

1. Shift hand strap to the side to expose screw head. Loosen screw with screwdriver to disassemble:

2. Insert Nut into center nut pocket of Slip Washer. White nylon inside Nut must be facing upward.

3. Insert Slip Washer with Nut into center hole of your IntelliSkin™.

4. While holding Nut in place, reassemble the RAM® HandStand™ from the outside of your IntelliSkin™, fully tightening down on the screw.

For a video demonstration of this assembly, visit www.rammount.com/part/RAM-GDS-HS1U

The RAM® HandStand is compatible with any IntelliSkin™ that features the unique circular interface on the back.

Nut Slip Washer HandStand™

Page 2: RAM® HandStand™Assembly Guide - rammount.com · RPR-INS-GDS-HS1 RAM® HandStand™Assembly Guide 1. Shift hand strap to the side to expose screw head. Loosen screw with screwdriver

More GDS Accessories & Warranty Info

National Products Inc.8410 Dallas Ave SSeattle WA 98108Phone: (206) 763-8361Fax: (206) [email protected]

Visit for more GDS Products & Accessorieswww.gdstech.com

The exclusive NPI Lifetime Warranty states that all GDS™ non-electronic components and parts are warranted against defect in materials and workmanship for the life of the product or part. NPI’s Lifetime Warranty covers the product or its components only. The mounted device is not covered under the Lifetime Warranty and will not be replaced if damaged as a result of mount failure. This warranty is expressly limited to persons in the United States, and all foreign countries who purchase GDS™ for resale or use in the ordinary course of the buyer’s business. This warranty does not cover any product or part that has been abused, worn out, heated, ground or otherwise altered, used for a purpose other than that for which it was intended, or used in a manner inconsistent with any instructions regarding its use.

3 year warranty on all electronic componentsLifetime Warranty on all non-electronic components

RAM® Snap-Con™ GDS to Micro USB 2.0 AdapterP/N: RAM-GDS-AD1U

RAM® Shoulder Strap AccessoryP/N: RAM-GDS-SS1U

More GDS Accessories & Warranty Info

National Products Inc.8410 Dallas Ave SSeattle WA 98108Phone: (206) 763-8361Fax: (206) [email protected]

Visit for more GDS Products & Accessorieswww.gdstech.com

The exclusive NPI Lifetime Warranty states that all GDS™ non-electronic components and parts are warranted against defect in materials and workmanship for the life of the product or part. NPI’s Lifetime Warranty covers the product or its components only. The mounted device is not covered under the Lifetime Warranty and will not be replaced if damaged as a result of mount failure. This warranty is expressly limited to persons in the United States, and all foreign countries who purchase GDS™ for resale or use in the ordinary course of the buyer’s business. This warranty does not cover any product or part that has been abused, worn out, heated, ground or otherwise altered, used for a purpose other than that for which it was intended, or used in a manner inconsistent with any instructions regarding its use.

3 year warranty on all electronic componentsLifetime Warranty on all non-electronic components

RAM® Snap-Con™ GDS to Micro USB 2.0 AdapterP/N: RAM-GDS-AD1U

RAM® Shoulder Strap AccessoryP/N: RAM-GDS-SS1U

RPR-INS-GDS-HS1

RPR-INS-GDS-HS1