"RADIAL II"CENTER DRIVE SILO

UNLOADER

OWNER'S MANUAL

230 Industriel Blvd, Saint-GermainQuebec, Canada

J0C 1KOTel.: (819) 395-4282Fax: (819) 395-2030www.valmetal.cominfo@valmetal.com

TABLE OF CONTENT

Safety...............................................................................................................................................1

Safety precautions..........................................................................................................................2

DANGER: Silo gas is deadly!.......................................................................................................3

General information ......................................................................................................................4

Operation ........................................................................................................................................5Operating the silo unloader...............................................................................................5Lower blower spout ...........................................................................................................5Maintain proper operating conditions .............................................................................6Raising center drive unloader...........................................................................................6Prepare unloader for raising.............................................................................................7Operating the winch to raise unloader.............................................................................7Setting up the unloader for unloading .............................................................................8Start unloading...................................................................................................................8

Adjustments....................................................................................................................................9Set counterweights .............................................................................................................9Adjust blower spout...........................................................................................................9Adjust frost cutter clearance.............................................................................................9Tension drive belts ...........................................................................................................10Set the guide wheel...........................................................................................................10Set pressure on tension wheel .........................................................................................10Adjust slip clutch pressure..............................................................................................10

Lubrication ...................................................................................................................................11

Trouble shooting ..........................................................................................................................12

Installation ....................................................................................................................................13Install tripod .....................................................................................................................13Install worm gear hoist VM-2125...................................................................................15Install worm gear hoist motorisation .............................................................................16Install unloader ................................................................................................................17

Repair parts..................................................................................................................................27

TT, Rad; Revised 2006-03-01

INSTALL WORM GEAR HOIST VM-2125

TT, PT, Rad; Revised 2007-10-12 Page 16

INSTALL WORM GEAR HOIST MOTORISATION

TT, PT, Rad; Revised 2007-10-12 Page 17

"RADIAL II"CENTER DRIVE SILO

UNLOADER

PARTS MANUAL

230 Industriel Blvd, Saint-GermainQuebec, Canada

J0C 1KOTel.: (819) 395-4282Fax: (819) 395-2030www.valmetal.cominfo@valmetal.com

STANDARD TRIPOD PARTS

KEY PART NO# REQ'D DESCRIPTION KEY PART NO# REQ'D DESCRIPTION1 00393 2 Secondary Leg 12' (8'2") 4 00413 3 Pin Safety

00394 2 Secondary Leg 14' (9'6") 5 B814HC5PST 2 Bolt 5/8 x 2 ¾ Special Shank00395 2 Secondary Leg 16' (10'4") 6 N8HCCP 4 Nut 5/8 C/Lock00396 2 Secondary Leg 18' (11'6") 7 00419 2 Cable Pulley00397 2 Secondary Leg 20' (12'10") 8 00415 1 Tri-Plate Pulley Weldment00399 2 Secondary Leg 24' (15'6") 9 00409 1 Tri-Plate Pulley Assembly00402 2 Secondary Leg 30' (20'5") 10 B809HC5B 3 Bolt 5/8 x ½

2 00421 1 Main Leg Assy 12' 11 W8LP 3 Lockwasher 5/800422 1 Main Leg Assy 14'00423 1 Main Leg Assy 16'00424 1 Main Leg Assy 18'00425 1 Main Leg Assy 20'00427 1 Main Leg Assy 24'00430 1 Main Leg Assy 30'

PART NO# DESCRIPTION00967 12' Tri-Pod Assy Complete00968 14' Tri-Pod Assy Complete00969 16' Tri-Pod Assy Complete00970 18' Tri-Pod Assy Complete00971 20' Tri-Pod Assy Complete

PART NO# DESCRIPTION02364 22' Tri-Pod Assy Complete00972 24' Tri-Pod Assy Complete02366 26' Tri-Pod Assy Complete02367 28' Tri-Pod Assy Complete02368 30' Tri-Pod Assy Complete

TT, PT, Rad; Revised 2008-11-05 28

TT, Rad; Revised 2006-03-01

WORM GEAR HOIST #VM-2125

KEY PART # DESCRIPTION1 VS-2132 Hoist drum assembly2 40-242824 Oilite bushing 1½" x 1¾" x 1 ½"3 VS-2129 Bearing (oilite bushing included)4 VS-2128 Base5 VS-2161 Housing6 40-242824 Oilite bushing 1½" x 1¾" x 1½"7 VS-2162 Worm gear8 VS-2164 Cover9 39-25627 Oil seal

10 94-1460-98 Snap ring11 40-15101 Bearing12 40-15245 Cup13 VS-2140 Spacer14 VS-2166 Snap ring15 VS-2192 Shaft16 VS-2193 Worm17 VS-2149 Crank18 VS-2153 Pulley19 VS-2155 Brake mount20 VS-2154 Belt brake

KEY PART # DESCRIPTION21 VS-2100 Hoist mount chanel22 VS-2160 Socket head cap screw 5/16 x 1/223 94-110 Plug 3/8-14 npt24 94-060 Oil level25 94-110 Plug 3/8-14 npt26 02C46-0020 5/16" x 1" square head setscrew27 --- #8 x 3/4 Round head machine screw28 02C22-0006 #8 washer29 02C07-0013 #8 nut30 99-380 3/8 x 3/8 x 1½ key31 VS-2194 Spring32 99-173 1/2" x 1" hex. bolt33 99-343 1/2" washer34 99-353 1/2" lock washer35 99-143 3/8" x 1" hex. bolt36 99-352 3/8" lock washer37 99-299 "U" bolt 1/2"38 01C69-0140 1/8" x 1" cotter pin

TT, PT, Rad; Revised 2008-11-05 29

MOTORIZED WORM GEAR HOIST

1

4 39

6

13 7 59 8

1014 12

16 8

2015 10 22

11 21

1918

17

KEY PART # DESCRIPTION1 VM-2125-SEUL Worm gear hoist2 VS-2118 Shield brace3 VS-2102 Reversing switch4 VS-2115-99 Jack shaft ¾″ ∅5 17-041-.75 3/4 hp motor6 VS-2112-99 Auxiliary shaft support7 VS-2110 Locking bolt8 40-EFL-12J Bearing9 40-FL4 Flange

10 VS-2119 Shield bracket11 99-338 Washer SAE 13/1612 60-35B15-.75 Sprocket 35-B-15 x ¾13 60-35B72-1 Sprocket 35-B-72 x 114 60-35-94 Roller chain15 VS-2120 Shield16 41-MA100-.75 Pulley MA100 x ¾17 42-A38 Belt A3818 41-4-2 Step pulley19 VS-2107-99 Motor mount pin 3/8″ ∅20 VS-2117 Shield mount21 VS-2108 Tension rod22 VS-2106 Motor mount23 VM-2164 Motor guard (incl. guard bracket CV-4423) (option)24 CV-4423 Guard bracket (option)

TT. PT, Rad; Revised 2008-11-05 30

BLOWER SPOUT & DOOR ARM2

4 1

13

3 14

39a

38

811

97

32 45

630

4039b

40 28

27

37

31

33 34

18

35

56 28

25

3637

1519

17 16

2423 22

1210

KEY PART NO# REQ'D DESCRIPTION1 00001 1 Spout Assembly 12' - 14' (72")

00004 1 Spout Assembly 16' (84")00006 1 Spout Assembly 18' (95")01407 1 Spout Assembly 20' (108")00773 1 Spout Assembly 24' (120")

2 P109B 2 Cotter Pin 3/16 x 1 ½3 02710 1 Spout Holder4 02711 2 Spout Holder Bracket5 W4FP 4 Washer 3/8 Flat6 N4HCCP 4 Nut 3/8 Unc7 S607SS5CP 2 Set Screw ½ x 1 Sh8 00361 1 Spout Brkt Pipe F 12'-16'

00362 Spout Brkt Pipe F 18'-30'9 00302 1 Door Arm Hoe Assy 5' (12')

01843 1 Door Arm Hoe Assy 6' (14')00303 1 Door Arm Hoe Assy 7' (16'-18')01404 1 Door Arm Hoe Assy 8' (20'-24')

10 00452 1 Hoe Bracket11 B627HC5P 1 Bolt ½ x 6 HH NC12 03046 1 Torque Arm Wldmt. 12' (48")

02721 1 Torque Arm Wldmt. 14' (60")02722 1 Torque Arm Wldmt. 16' (72")02723 1 Torque Arm Wldmt. 18'-20' (84")02724 Torque Arm Wldmt. 24' (108")

13 00523 1 Cable Spool Universal14 00524 1 Hitch Pin W/Clip15 03719 2 Connector Pin16 03430 2 Spring17 99-429 2 1/8 Hairpin

KEY PART NO# REQ'D DESCRIPTION18 03429 1 Yoke Assy (12'-14')

03428 1 Yoke Assy (16'-24')19 P2RPG 2 Roll Pin ¼ x 1 3/822 B610HC5P 2 Bolt ½ x 1 ¾ Unc23 W6LP 6 Washer ½ Lock24 W6FP 2 Washer ½ Flat25 00040 2 Yoke Bushing27 02763N 1 Collector Ring Rad 1 Phase

03373N 1 Collector Ring Rad 3-Phase28 03574 1 Torque Arm Lifting Ear Rh (12'-14')

03575 1 Torque Arm Lifting Ear Lh (12'-14')03424 1 Torque Arm Lifting Ear Rh (16'-24')03425 1 Torque Arm Lifting Ear Lh (16'-24')

30 00520 1 Cord Holder Assembly31 00003 1 Spout Liner SS

02851 1 UHMW Plastic Spout Liner32 B408HC5P 8 Bolt 3/8 x 1 ¼ Unc33 S102RFP 4 Screw #10-32 x 3/834 N1HFP 4 Nut #10-3235 02111 1 Short Spout Galv.36 B613HC5P 2 Bolt ½ x 2 ½ Unc37 N6HCCP 3 Nut ½ CL38 VS-3129 1 Adjusting Handle39 03935 1 Spout Support Stabilizer Kit (18' - 30')39a 03934 1 Spout Support Stblzr Slide Tube39b 03933 1 Spout Support Stblzr Tube40 N6HCP 2 Nut ½ HX NC

Radial II; Revised 2008-11-05 31

27 N2HCBR 6 Nut ½ Brass28 S104RFBR 6 RHMS #10-32 x 5/829 Z2TS 2 Zerk ¼-28 Threaded Straight30 00802 1 Ring Holder Kit31 00801 1 Brush Holder Kit32 S202RCP 2 RHMS ¼ x 3/833 S108RFBR 3 RHMS #10-32 x 1 ¼ Brass34 02829 1 Bearing Collector Ring35 02785 1 Center Spacer36 B608HC5P 4 Bolt ½ x 1 ¼37 W6LP 4 Washer ½ Lock38 00044 3 Connector 3/16 Hole Elect40 N4HCP 4 Nut 3/8 HX NC41 01960 1 Serial # Sticker - 2 ¾ In.42 S103RFP 1 10-32 x ½ RHMS P43 50326 1 Ground Strap (3-Phase)44 00029 1 Ground Strap (1-Phase)

HANSON CENTER DRIVE COLLECTOR RING

KEY PART NO# REQ'D DESCRIPTION02763N Collector Ring-1PH Rad03373N Collector Ring-3PH Rad

1 00768 1 Serial # Plate2 00023 1 Gasket, Serial # Plate3 00010 1 Casting Machined Top4 Z2TA 2 Zerk 45 Deg. ¼-28 Grease5 02495 3 Connector ¼ Hole Elec. (1 Phase)

411

20 21 2

3637

524

19 2840

02495 8 Connector ¼ Hole Elec. (3 Phase)6 00013 1 Ring Holder Plastic Machined 27

3

7 00014 1 Ring Assy Large 268 00017 1 Ring Assy Medium 449 00019 1 Ring Assy Small

10 00057 1 Gasket Felt11 00011 1 Casting Machined Bottom 612 02783N 1 Sprocket Top Drive 30 43

02784N 1 Sprocket Botton Drive13 MPS 1 Pipe Strap ¾" (1-Phase)

MPS1 1 Pipe Strap 1" (3-Phase)14 00056 1 Brush Holder Cover 7

15 00051 1 Cord Bottom 1-Phase 6/3 (42.5") 802490 1 Cord Bottom 3-Phase 6/4 (42") 9

16 00055 3 Copper Tabs17 00049 6 Brush18 00050 1 Brush Holder Box (3 Ring) 1019 01984 1 Cord Connector 1 x ¾ W/T (1-Ph)

01985 1 Cord Connector 1 x 7/8 W/T (3-Ph) 1120 01845 1 Cord Top 6/3 (42.5") 29

00709 1 Cord Top 6/4 (42")21 S102RFP 6 RHMS #10-32 x 3/822 B414HC5P 4 Bolt HHCS 3/8 x 2 ¾ 1723 W4LP 4 Washer 3/8 Lock 33 1324 N1HFBR 6 Nut #10-32 Brass 18

(3-Phase Only)

28

3425 02800N 1 Coll. Ring Sprkt Assy 31 42 1626 M209BR 3 Bolt Stud ¼ x 1 ½ Brass 24

1624

12

32 14 35 25

3812

1523

4 22

Radial II; Revised 2008-11-05 32

HANSON 3-24 BLOWER ASSEMBLY

KEY PART NO# REQ'D DESCRIPTION02566 Complete Blower Assembly

1 02565 1 Blower Shell 24 Wldmnt2 02569 1 Blower Insert Weldmnt 243 02567 1 Blower Base Weldmnt 24 HR4 00998 1 Rotor 3-24 Machined5 00863 3 Paddle, Machined6 00845 3 Pin 1 Inch Paddle 24-28 Blwr7 00870 AR Washer 1 x 14 Ga8 P2RPG 6 Roll Pin ¼ x 1 3/89 S504SSCB 1 Set Screw

10 00874 AR Machinenry Bushing01308 AR Shim washer

11 03545 1 Blower shaft12 K315S 1 Key 5/16 sq x 313 01662 1 Flangette Outside w/Notch14 01661 1 Flangette Inside w/Notch17 00954 2 Bearing w/LC. Collar 1 3/818 B406HC5P 8 Bolt 3/8 x 7/819 W4LP 8 Washer 3/8 Lock20 N4HCP 12 Nut 3/821 B406HF5P 6 Bolt 3/8 x 7/8 Unf22 N4HTF8P 6 Nut 3/8 Top Lock23 00077 1 Flangette Inside W/O Zerk24 00078 1 Flangette Outside W/O Zerk25 B411CC5P 4 Bolt 3/8 x 2 Crg26 00887 2 Lifting Strap27 N8HCCP 2 Nut 5/8 Clock

TT, PT, Rad; Revised 2006-03-01 33

HANSON 3-28 BLOWER ASSEMBLYPillow Block Enduro Thro

1A8

1B 25

6

34

9 7

18 10

12

11

17

1514

2020 13 16

19

KEY PART NO# REQ'D DESCRIPTION03550 Complete PB Blower03549 1 Blower Shell Wldmt 28 Enduro

1A N8HCCP 2 Nut 5/8 Lock1B 00887 2 Lifting Strap2 01775 1 Blower Top, Insert Weldmnt 28 (including item 1A & 1B)3 03622 1 Blower Base Weld Enduro 28 (including item 13 & 20)4 03249 1 Rotor 3/28 Machined5 00863 3 Paddle, Machined6 00951 3 Pin Kit (including item 7 & 8)

00845 3 Pin 1 Inch Paddle 24-28 blwr7 00870 AR Washer 1 x 14 Ga8 P2RPG 6 Roll Pin ¼ x 1 3/89 S504SSCB 1 Set Screw

10 00831 2 Small Spacer11 03545 1 Blower Shaft12 K315S 1 Key 5/16 x 313 B408HC5P 4 Bolt 3/8 x 1 ¼14 W6LP 4 Washer ½ Lock15 B607HC5P 4 Bolt ½ x 116 04634 AR Shim .025"17 40-HCPA207-22 2 P.B. Bearing Complete18 B406HC5P 8 Bolt 3/819 W4LP 8 Washer 3/8 Lock20 N4HCP 8 Nut 3/8

TT, PT, Rad; Revised 2007-10-12 34

MOTOR MOUNT AND DRIVE

KEY PART NO# REQ'D DESCRIPTION2 41-4B46-SD 1 Pulley Motor, 4B463 41-SD-1.125 1 Hub SD-1 1/8 (5 & 7 ½ HP)

41-SD-1.375 1 Hub SD 1 3/8 (10 HP)4 42-B79 2 Belt B79 (for 28" Blower TT, PT)

42-B76 2 Belt B76 (for 24" Blower TT, PT)42-B87 2 Belt B87 (for 28" Blower Rad)42-B83 2 Belt B83 (for 24" Blower Rad)

5 42-B43 2 Belt B436 00191 1 Shield, Main Belt Guard (TT, PT)

01152 1 Shield, Main Belt Guard (Rad)7 03364 1 Decal New Hanson Sticker

02251 1 Decal Belt Guard Warning8 00446 2 Main Belt Buard Bracket9 B307HC5P 6 Bolt 5/16 x 110 W3LP 6 Washer 5/16 Lock11 N3HCP 6 Nut 5/16 Hx12 B609HC5P 2 Bolt ½ UNC x 1 ½13 N6HCP 4 Nut ½ UNC14 W6LP 2 Washer ½ Lock16 B409HC5P 1 Bolt 3/8 x 1 ½17 B408HC5P 3 Bolt 3/8 x 1 ¼18 W4FP 4 Washer 3/8 Flat19 W4LP 4 Washer 3/8 Lock20 N4HCP 8 Nut 3/8 UNC21 S613SSCP 2 Set Bolt ½ x 2 ½ SH22 00193 1 Motor Plate Assembly23 41-2B80-SK 1 Pulley 2B8024 41-SK-1.375 1 Hub SK 1 3/825 41-2B60-SDS 1 Pulley Transmission, 2B6026 41-SDS-1 1 Hub SDS 127 00197 1 Belt Tightener Tension Tab

TT, PT, Rad; Revised 2008-11-05 35

COUNTER WEIGHTS, RAILS & BACK CROSS MEMBER

3

4

KEY PART NO# REQ'D DESCRIPTION1 02895 1 Rear Tension Wheel Wldmt (12' Only)

02703 1 Rear Tension Wheel tube Wldmt2 01550 1 Wall Wheel3 03800 1 Connector pin4 01C69-0140 1 Cotter Pin 1/8" x 1"5 N8HCCP 1 Locknut 5/86 00201 1 Back Cross, Weldmt7 02708 1 Rear Tension Wheel Brkt Wldmt8 02735 2 Counter-Weight Angle 12' (32")

02736 2 Counter-Weight Angle 14' (36")02737 2 Counter-Weight Angle 16' (48")02738 2 Counter-Weight Angle 18' (60")02739 2 Counter-Weight Angle 20' (72")02741 2 Counter-Weight Angle 24' (96")

10 B407HC5P 12 Bolt 3/8 x 111 W4LP 16 Washer 3/8 Lock12 N4HCP 12 Nut 3/8 Hx

KEY PART NO# REQ'D DESCRIPTION13 B407HF8P 4 Bolt 3/8 x 1 UNF14 N4HCFP 4 Nut 3/8 UNF Hex21 B617HC5P 1 Bolt ½ x 3 ½23 B414HC5P 2 Bolt 3/8 x 2 ¾24 00770 1 Counter-Weight Brace Angle Lh (24')

00835 1 Counter-Weight Brace Angle Rh (24')25 B408HC5P 2 Bolt 3/8 x 1 ¼26 N4HCP 3 Nut 3/830 00278 AR C-Iron Counter Weight Assy31 00487 1 Tension Arm Chain32 00488 1 Spring, Tension Arm34 W8FP 2 Washer 5/8 Flat35 VS-3129 2x Adjusting Handle36 03784 1 Chain Tightener Handle

Radial II; Revised 2008-11-05 36

CENTER DRIVE UNIT

31 32 33

26

3818 44 37 46

29 4322 20

10 3132 33 42 2345

18

29

1419 22

12 1615 34

27 28

139

86

7

45 1

32 0

35 36

34 35 36

21

3435 36

17

KEY PART NO# REQ'D DESCRIPTION KEY PART NO# REQ'D DESCRIPTION0 03403 Drive Unit Assy Self Adj 24 00820 1 Angle Bracket1 03269 1 Clutch Assembly Hex 25 00836 1 Chain Tightener Tab2 00515 1 Nut Adjusting 1 7/8-12 Trd 26 03303 1 Torque Tube (for 3-24 Blower)3 02010 1 NBR 2 7/8 OD x 1 7/8 ID, 14 GA 03304 1 Torque Tube (for 4-28 Blower)4 02777 1 Spring, Clutch 27 03434 1 Sprocket Kit C.D. #50-155 03266 1 Clutch Drive Collar Complete 27a 03095 1 Key Retainer (Rubber Band)6 00512 2 Clutch Half 27b 03433 1 Sprocket #50-15 (Drilled)7 02776 1 Clutch Oiler (felt) 27c 03438 1 #50 Offset Links (CD)8 03371 1 Sprocket #50-60 (Drilled) 27d P1158 1 Cotter Pin 3/16 x 39 03265 1 Clutch Body Weldment Hex 27e P406G 1 Roll Pin 3/8 x 1 1/16

10 03360 1 Shield Drive Unit PLST 428 28 03422 1 #50 Roller Chain 93 Pin (28" Blower)03361 1 Shield Drive Unit PLST 324 03423 1 #50 Roller Chain 83 Pin (24" Blower)

12 02701 1 Shield Mouting Bracket 29 00870 2 NRB 1 ½ OD x 1 ID, 14 GA13 02798 1 5-Tooth CD Chaindrive Sprocket 31 B407HC5P 8 Bolt 3/8 x 1 Unc14 K219S 1 Key ¼ Sq. x 4 32 W4LP 6 Washer 3/8 Lock15 02796 1 Radial Drive Shaft 33 N4HCP 12 Nut 3/8 Unc16 02751 1 Drive Unit Base Plate 34 B607HC5P 4 Bolt ½ x 1 Unc17 02893 1 Drive Unit Extension (for 4-28 Blower) 35 W6LP 5 Washer ½ Lock18 02791 2 Chain Idler Wheel w/ bushing 36 N6HCP 4 Nut ½ Unc

40-162020 1 Oilite bushing 37 1 Nut ½ Jam19 02790 1 Collar 1 ¼, Drive Unit Set 38 1 Bolt ½ x 1 ¾ FT20 03404 1 Drive Unit Weld Self Adj 42 03413 1 Adj. Idler Pivot Shaft

40-202420 2 Oilite bushing 43 03414 1 Spring Danley-Drive Unit21 03140 1 Drive Unit spacer Channet 44 03412 1 Spring Tension Button22 P2RPG 2 Roll Pin 45 B613HC5P 1 Bolt ½ x 2 ½ Unc23 02758 1 Chain Ring-Drive Diff. (before 2007-08-01) 46 N6HCCP 1 Nut ½ CL

02758N 1 Chain Ring-Drive Diff. (after 2007-08-01)

Radial II; Revised 2007-11-16 37

SIDERAILS, KICK GUARDS & COVERS

38

KEY PART NO# REQ'D DESCRIPTION17 03127 2 Blower Mouniting Tube18 00445 1 Shield Bottom Belt Brkt19 00914 1 Shield Bottom Belt 4-2820 00187 1 Blower Shield Back Small21 02702 1 Side Blower Shield

03581 1 Shield Side Blower 28PBCD22 02687 1 Guide Wheel Tube 12' (46")

02688 2 Guide Wheel Tube 14'-18' (68")02689 4 Guide Wheel Tube 20' (80")02690 4 Guide Wheel Tube 24' (120")

23 02897 2 Wall Wheel Wldmt 12'02731 2 Wall Wheel Tube Wldmt 3' (14'-16')02732 2 Wall Wheel Tube Wldmt 4' (18'-20')

24 01550 2 Wall Wheel25 W4FP 2 Washer 3/8 Flat27 N8HCCP 1 Nut 5/8 Lock35 00670 1 Trans Mt Angle Front36 02934 1 Grill Cover Supp. Str 18'-20'

2 Grill Cover Supp. Str 24'37 03489 1 Grill Cover Wldmt RH 12' (36 5/16")

03490 1 Grill Cover Wldmt LH 12' (36 5/16")03491 1 Grill Cover Wldmt RH 14' (48 5/16")03492 1 Grill Cover Wldmt LH 14' (48 5/16")03493 1 Grill Cover Wldmt RH 16' (60 5/16")03494 1 Grill Cover Wldmt LH 16' (60 5/16")03495 1 Grill Cover Wldmt RH 18' (72 5/16")03496 1 Grill Cover Wldmt LH 18' (72 5/16")03497 1 Grill Cover Wldmt RH 20' (84 5/16")03498 1 Grill Cover Wldmt LH 20' (84 5/16")

38 03487 1 Grille Sect. Weld LH 22-30 (54")03488 1 Grille Sect. Weld RH 22-30 (54")

39 03233 1 Grille Spt. Brkt Center (24')43 01517 1 Blank-Out Galvanized (24" Blower)44 03436 1 Adjusting Handle

SIDERAILS, KICK GUARDS & COVERS

KEY PART NO# REQ'D DESCRIPTION1 00226 1 Rail R.R. 14'-20' 78 Inch

00227 1 Rail R.R. 24' 90 Inch2 00229 1 Rail L.R. 14'-20' 78 Inch

00230 1 Rail L.R. 24' 90 Inch3 B407HC5P AR Bolt 3/8 x 14 W4LP AR Washer 3/8 Lock5 N4HCP AR Nut 3/8 Hx6 00232 1 Rail L.F. 14'-16' 63 Inch

00233 1 Rail L.F. 18'-20' 87 Inch00234 1 Rail L.F. 24' 99 Inch

7 00238 1 Rail R.F. 14'-16' 63 Inch00239 1 Rail R.F. 18'-20' 87 Inch00240 1 Rail R.F. 24' 99 Inch

8 B307HC5P AR Bolt 5/16 x 19 W3LP AR Washer 5/16 Lock

10 N3HCP AR Nut 5/16 Hx11 00205 1 Kickguard Weldment 12' (63)

00206 1 Kickguard Weldment 14' (75)00207 1 Kickguard Weldment 16' (87)00208 1 Kickguard Weldment 18' (99)00209 1 Kickguard Weldment 20' (111)00211 1 Kickguard Weldment 24' (135)

12 00946 1 Shield Back Auger Galv Medium 12'-16' (63)00947 1 Shield Back Auger Galv Large 18'-24' (87)

13 00945 1 Shield Back Auger Galv Small 12'-20' (49 ½)2 Shield Back Auger Galv Small 24'

14 01285 1 Angle Plate SS16 01268 1 Rear SS Blw Filler Shield

Radial II; Revised 2007-10-12 39

AUGERS & IDLER FRAME ASSEMBLY

TT, PT, Rad; Revised 2008-11-05 40

AUGERS & ILDER FRAME ASSEMBLY

KEY PART NO# REQ'D DESCRIPTION1 00670 1 Trans Mtg angle Front 12'-24'

01289 1 Trans Mtg angle Front 30'2 B609HC5P 3 Bolt ½ x 1 ½3 W6LP 4 Washer ½ / Lock4 N6HCP 4 Nut ½5 B608HC5P 1 Bolt ½ x 1 ¼6 00671 1 Transmission Tab7 00997 1 Rear Trans. Mtg Brkt11 07100 1 Transmission, Twin Trac, Radial

07000 1 Transmission, Posi Trac12 B715HF5B 4 Bolt Shoulder 9/16 x 313 N7HTF8P 4 Nut 9/16 Lock Unf14 00935 2 Wall Wheel 1" - 1.032 Bore15 01314 2 Wall Wheel Bolt Ass'y (including item 16,17,18,23)

00168 2 Wall Wheel Bushing16 N9HCP 2 Nut ¾17 W9LP 2 Washer ¾ Lock18 W9FP 4 Washer ¾ Flat19 40-222624 2 Oilite Bearing SO 1.625 x 1.375 x 1.520 00961 2 Bearing Hanger21 P1.509B 2 Cotter Pin 7/3222 00934 1 Idler End Frame Assembly (including item 24)

00158 1 Idler End Frame Wldmt23 B919SC2P 2 Bolt ¾ x 424 00162 2 Bearing Bracket (Hanger Plate) (included with item

22)25 00150 1 Wall Chippers (Rh Thread)26 00146 1 Wall Chippers (Lh Thread)27 00155 1 Stub Shaft (Rh Thread)28 00154 1 Stub Shaft (Lh Thread)29 00765 1 Tooth Lh Starter30 00144 AR Teeth Auger Lh

00960 AR Auger Teeth Kit HD Lh31 00095 1 Heavy Duty Front Auger Assy for 12' (79 ¼")

00096 1 Heavy Duty Front Auger Assy for 14' (91 ¼")00097 1 Heavy Duty Front Auger Assy for 16' (103 ¼")00098 1 Heavy Duty Front Auger Assy for 18' (115 ¼")00099 1 Heavy Duty Front Auger Assy for 20' (127 ¼")00101 1 Heavy Duty Front Auger Assy for 24' (151 ¼")00104 1 Heavy Duty Front Auger Assy for 30' (187 ¼")

32 00766 1 Tooth Rh Starter33 00145 AR Teeth Auger Rh

00959 AR Auger Teeth Kit HD Rh34 00120 1 Heavy Duty Back Auger Assy for 12' (75 5/8")

00121 1 Heavy Duty Back Auger Assy for 14' (87 5/8")00122 1 Heavy Duty Back Auger Assy for 16' (99 5/8")00123 1 Heavy Duty Back Auger Assy for 18' (111 5/8")00124 1 Heavy Duty Back Auger Assy for 20' (123 5/8")00126 1 Heavy Duty Back Auger Assy for 24' (147 5/8")00129 1 Heavy Duty Back Auger Assy for 30' (183 5/8")

35 B407HC5P 4 Bolt 3/8 x 136 W4LP 4 Washer 3/837 N4HCP 4 Nut 3/838 B305CC2B AR Bolt 5/16 x ¾ Crg Std Knives40 N3HJCB AR Jam Nut 5/16 Black Std Knives52 03301 2 Plastic Spacer53 03394 2 Reinforcing Plate

TT, PT, Rad; Revised 2008-11-05 41

TT, Rad; Revised 2006-03-01

AUGER TRANSMISSION #07100

KEY PART # REQ'D DESCRIPTION KEY PART # REQ'D DESCRIPTION07100 Transmission Complete 19 00643 1 Cover plate

1 07001 1 Transmission casting 20 07064 8 Screw, Hex. head, M8 x 16 lg2 07050 4 Oil seal, bouble lips 22 00673 1 Trans. Dipstick 3/8 NPT3 07051 8 Tapered roller bearing 30207 23 07058 28 Washer ,Lock, Helical spring 8

mm5 07052 1 Output shaft spacer 24 M203B 1 Drain plug6 07009 1 Worm gear RH 30 teeth 26 07004 1 Shaft include worm RH7 07010 1 Output shaft 27 07006 1 Worm gear 24 teeth8 07053 3 Key, A type 28 07059 1 Cover (115 mm)9 07054 1 Key, ¼" x ¼" x 1" 29 07060 20 Screw, Hex. head, M8 x 20 lg

10 07054 AR Bearing shim 0.1 mm (72 mm) 35 07008 1 Worm gear 24 teeth07055 AR Bearing shim 0.3 mm (72 mm) 36 07011 1 Output shaft

13 07056 2 Cover with hole (72 mm)15 07057 1 Cover (72 mm) N/I 03270 1 RTV Sealant17 07003 1 RH & LH Worm18 K207S 1 Key, ¼" x ¼" x 1 ½"

TT, Rad; Revised 2007-10-12 42

Part no.' 02761