RAB.EstFailPs.Cell.pdf

4
Measurement of PS RAB assignment failure per cell (RAB.EstFailPs.Cell) Overview The CN in PS domain initiates the radio access bearer setup procedure by sending a RAB ASSIGNMENT REQUEST message to the RNC. After receiving the RAB ASSIGNMENT REQUEST message, the RNC selects an appropriate cell, allocates resources, and performs admission control based on the information in the message (such as service type, QoS, and priority), the traffic load of the system, and the networking strategy (such as DRD). The requirements of high-priority users are met preferentially(That is, when the resources are insufficient and the UEs with low-priority cannot set up the RAB, the RNC sends to the CN a RAB ASSGNMENT RESPONSE message if the queuing algorithm is enabled, indicating that the RAB is in the queue to wait for resources). If the admission of the RAB succeeds, the RNC starts the Iu transport connection setup procedure, the Iub radio bearer setup procedure, and the Uu radio bearer setup procedure. At last, the RNC sends to the CN a RAB ASSNMENT RESPONSE, indicating whether the RAB setup is successful. If DRD is enabled during the RAB setup, the RAB setup measurement is performed on the DRD target cell. Otherwise, the RAB setup measurement is performed on the DRD source cell. The RAB setup procedure is as follows. Figure 1 RAB Setup Flow Page 1 of 4 Measurement of PS RAB assignment failure per cell(RAB.EstFailPs.Cell) 24/07/2013 mk:@MSITStore:C:\Solutions\VendorDocumentation\UTRAN\Huawei\R12\BSC690...

description

RAB.EstFailPs.Cell.Explanation

Transcript of RAB.EstFailPs.Cell.pdf

Page 1: RAB.EstFailPs.Cell.pdf

Measurement of PS RAB assignment failure per cell(RAB.EstFailPs.Cell)

Overview

The CN in PS domain initiates the radio access bearer setup procedure by sending a RAB ASSIGNMENT REQUEST message to the RNC.After receiving the RAB ASSIGNMENT REQUEST message, the RNC selects an appropriate cell, allocates resources, and performs admission control based on the information in the message (such as service type, QoS, and priority), the traffic load of the system, and the networking strategy (such as DRD). Therequirements of high-priority users are met preferentially(That is, when the resources are insufficient and the UEs with low-priority cannot set up the RAB, the RNC sends to the CN a RAB ASSGNMENT RESPONSE message if the queuing algorithm is enabled, indicating that the RAB is in the queue to wait forresources). If the admission of the RAB succeeds, the RNC starts the Iu transport connection setup procedure, the Iub radio bearer setup procedure, and the Uu radio bearer setup procedure. At last, the RNC sends to the CN a RAB ASSNMENT RESPONSE, indicating whether the RAB setup is successful. If DRD is enabled during the RAB setup, the RAB setup measurement is performed on the DRD target cell. Otherwise, the RAB setup measurement is performed on the DRD source cell.The RAB setup procedure is as follows.

Figure 1 RAB Setup Flow

Page 1 of 4Measurement of PS RAB assignment failure per cell(RAB.EstFailPs.Cell)

24/07/2013mk:@MSITStore:C:\Solutions\VendorDocumentation\UTRAN\Huawei\R12\BSC690...

Page 2: RAB.EstFailPs.Cell.pdf

Page 2 of 4Measurement of PS RAB assignment failure per cell(RAB.EstFailPs.Cell)

24/07/2013mk:@MSITStore:C:\Solutions\VendorDocumentation\UTRAN\Huawei\R12\BSC690...

Page 3: RAB.EstFailPs.Cell.pdf

Table 1 describes the measurement points shown in Figure1.

Measurement Counters

Measurement points Description

E VS.RAB.FailEstabPS.DLIUBBand.Cong,VS.RAB.FailEstabPS.ULIUBBand.Cong, VS.RAB.FailEstabPS.ULCE.Cong,VS.RAB.FailEstabPS.DLCE.Cong, VS.RAB.FailEstabPS.Code.Cong,VS.RAB.FailEstabPS.ULPower.Cong,VS.RAB.FailEstabPS.DLPower.Cong

N VS.RAB.FailEstabPS.TNL

F VS.RAB.FailEstabPS.IubFail,VS.RAB.FailEstabPS.ULCE.Cong, VS.RAB.FailEstabPS.DLCE.Cong

G VS.RAB.FailEstabPS.UuFail,VS.RAB.FailEstabPS.UuNoReply, VS.RAB.FailEstabPS.RBIncCfg,VS.RAB.FailEstabPS.RBCfgUnsupp,VS.RAB.FailEstabPS.PhyChFail

K VS.RAB.FailEstabPS.RNL, VS.RAB.FailEstabPS.TNL

ID Counter Description OriginalRelease

67192612 VS.RAB.FailEstabPS.DLIUBBand.Cong Number of Failed PS RAB Establishments for Cell (DL Iub Bandwidth Congestion)

Earlier than V900R011

67192613 VS.RAB.FailEstabPS.ULIUBBand.Cong Number of Failed PS RAB Establishments for Cell (UL Iub Bandwidth Congestion)

Earlier than V900R011

67189556 VS.RAB.FailEstabPS.RNL Number of Failed PS RAB Establishments for Cell (Radio Network Layer Cause)

Earlier than V900R011

67189557 VS.RAB.FailEstabPS.TNL Number of Failed PS RAB Establishments for Cell (Transport Network Layer Cause)

Earlier than V900R011

67190408 VS.RAB.FailEstabPS.ULCE.Cong Number of Failed PS RAB Establishments for Cell (UL CE Congestion)

Earlier than V900R011

67190409 VS.RAB.FailEstabPS.DLCE.Cong Number of Failed PS RAB Establishments for Cell (DL CE Congestion)

Earlier than V900R011

67179967 VS.RAB.FailEstabPS.Code.Cong Number of Failed PS RAB Establishments for Cell (Code Congestion)

Earlier than V900R011

67193540 VS.RAB.FailEstabPS.RBIncCfg Number of Failed PS RAB Establishments for Cell (UU interface invalid configuration)

V900R012

67193541 VS.RAB.FailEstabPS.RBCfgUnsupp Number of Failed PS RAB Establishments for Cell (Configuration unsupported of UEduring the RB setup procedure)

V900R012

67193543 VS.RAB.FailEstabPS.UuNoReply Number of Failed PS RAB Establishments for Cell (No reply of UE during the RBsetup procedure)

V900R012

67193542 VS.RAB.FailEstabPS.PhyChFail Number of Failed PS RAB Establishments for Cell (Physical channel failure of UEduring the RB setup procedure)

V900R012

67193613 VS.RAB.FailEstabPS.ULPower.Cong Number of Failed PS RAB Establishments for Cell (UL Power Congestion)

V900R012

67193614 VS.RAB.FailEstabPS.DLPower.Cong Number of Failed PS RAB Establishments V900R012

Page 3 of 4Measurement of PS RAB assignment failure per cell(RAB.EstFailPs.Cell)

24/07/2013mk:@MSITStore:C:\Solutions\VendorDocumentation\UTRAN\Huawei\R12\BSC690...

Page 4: RAB.EstFailPs.Cell.pdf

Counter Relationship

Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.

for Cell (DL Power Congestion)

73393837 VS.RAB.FailEstabPS.IubFail Number of Failed PS RAB Establishments Due to Radio Link Configuration Failure for Cell

V900R012

73393838 VS.RAB.FailEstabPS.UuFail Number of Failed PS RAB Establishments Due to Uu Interface Configuration Failurefor Cell

V900R012

67179930 VS.RAB.FailEstabPS.Unsp Number of Failed PS RAB Establishments for Cell (Unsupported Capabilities)

Earlier than V900R011

73394298 VS.RAB.FailEstabPS.Cong Number of Failed PS RAB Establishments for Cell (Congestion)

V900R012

Counter Sub Counter

VS.RAB.FailEstabPS.UuFail VS.RAB.FailEstabPS.RBIncCfgVS.RAB.FailEstabPS.RBCfgUnsuppVS.RAB.FailEstabPS.UuNoReplyVS.RAB.FailEstabPS.PhyChFail

VS.RAB.FailEstabPS.RNL VS.RAB.FailEstabPS.IubFailVS.RAB.FailEstabPS.UuFail

VS.RAB.FailEstabPS.Unsp VS.RAB.FailEstabPS.Cong

Page 4 of 4Measurement of PS RAB assignment failure per cell(RAB.EstFailPs.Cell)

24/07/2013mk:@MSITStore:C:\Solutions\VendorDocumentation\UTRAN\Huawei\R12\BSC690...