R2AP Panel Control Board - Winmate

R2AP Panel Control Board

Powerful graphics processing board, providing high-quality images for TFT

panel with superior resolution up to UHD 4096x2160. Various signal input:

VGA, HDMI, analog RGB, and output formats: LVDS, eDP & V-by-one

V110

User Manual Version 1.0

Manual Number: 91521112100N

User Manual II

Preface

Copyright Notice

No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer.

Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners.

Disclaimer We reserve the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. We assume no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright, or masks work rights to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described in this manual are for illustration purposes only. We make no representation or warranty that such application will be suitable for the specified use without further testing or modification.

Warranty We warrant that each of its products will be free from material and workmanship defects for a period of one year from the invoice date.(Standard is one year, extended warranty will need to discuss with our sales representatives. If the customer discovers a defect, we will, at its option, repair or replace the defective product at no charge to the customer, provided it is returned during the warranty period of one year, with transportation charges prepaid. The returned product must be properly packaged in its original packaging to obtain warranty service. If the serial number and the product shipping data differ by over 30 days, the in-warranty service will be made according to the shipping date. In the serial numbers the third and fourth two digits give the year of manufacture, and the fifth digit means the month (e. g., with A for October, B for November and C for December). For example, the serial number 1W16Axxxxxxxx means October of year 2016.

User Manual III

Packing List Before using this Motherboard, please make sure that all the items listed below are present in your package: R2AP A/D Board User Manual Driver CD If any of these items are missing or damaged, contact your distributor or sales representative immediately.

Customer Service We provide a service guide as below for any problem by the following steps: First, contact your distributor, sales representative, or our customer service center for technical support if you need additional assistance. You need to prepare the following information before you call: Product serial number Peripheral attachments Software (OS, version, application software, etc.) Detailed problem description The exact wording of any error messages In addition, free technical support is available from our engineers every business day. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products. Please do not hesitate to call or e-mail us.

User Manual IV

Advisory Conventions

Four types of advisories are used throughout the user manual to provide helpful

information or to alert you to the potential for hardware damage or personal injury.

These are Notes, Important, Cautions, and Warnings. The following is an example of

each type of advisory.

NOTE:

A note is used to emphasize helpful information

IMPORTANT:

An important note indicates information that is important for you to

know.

CAUTION

A Caution alert indicates potential damage to hardware and explains how

to avoid the potential problem.

WARNING!

An Electrical Shock Warning indicates the potential harm from electrical

hazards and how to avoid the potential problem.

User Manual V

Safety Precautions

CAUTION

Always ground yourself to remove any static charge before

touching the board. Modern electronic devices are very sensitive to

static electric charges. As a safety precaution, use a grounding wrist

strap at all times. Place all electronic components in a

static-dissipative surface or static-shielded bag when they are not

in the chassis.

Safety and Warranty

1. Please read these safety instructions carefully.

2. Please keep this user manual for later reference.

3. Please disconnect this equipment from any AC outlet before cleaning. Do not

use liquid or spray detergents for cleaning. Use a damp cloth.

4. For pluggable equipment, the power outlet must be installed near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or

letting it fall could cause damage.

7. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

8. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

9. All cautions and warnings on the equipment should be noted.

10. If the equipment is not used for a long time, disconnect it from the power

source to avoid damage by transient over-voltage.

11. If any of the following situations arises, get the equipment checked by service

personnel:

A. The power cord or plug is damaged.

B. Liquid has penetrated into the equipment.

C. The equipment has been exposed to moisture.

D. The equipment does not work well, or you cannot get it to work according

to the user’s manual.

E. The equipment has been dropped and damaged.

F. The equipment has obvious signs of breakage.

User Manual VI

Revision History

User Manual

Version Board Version Date Note Author

1.0 V110 4-May-2016 Initial release Austin Chang

User Manual VII

Contents

Table of Contents

PREFACE .............................................................................................................................................. I

CHAPTER 1 GENERAL INFORMATION ................................................................................................ 10

1.1 INTRODUCTION ................................................................................................................................. 10

1.2 FEATURES ........................................................................................................................................ 10

1.3 HARDWARE SPECIFICATIONS ................................................................................................................ 11

1.4 FUNCTIONAL DESCRIPTION.................................................................................................................. 12

1.5 PHYSICAL DESCRIPTION ...................................................................................................................... 13

CHAPTER 2 HARDWARE INSTALLATION ............................................................................................ 15

2.1 MOTHERBOARD COMPONENTS ............................................................................................................ 15

2.1.1 Front Side ............................................................................................................................. 15

2.1.2 Rear Side .............................................................................................................................. 16

2.1.3 I/O Side ................................................................................................................................. 16

2.2 I/O EQUIPMENT INSTALLATION ............................................................................................................ 17

2.2.1 Power ................................................................................................................................... 17

2.2.2 Power Cable ......................................................................................................................... 17

2.3 OPTIONS ......................................................................................................................................... 17

2.3.1 VGA Cable ............................................................................................................................ 17

2.3.2 DVI-D Cable .......................................................................................................................... 17

2.3.3 HDMI Cable .......................................................................................................................... 17

2.3.4 Display Port Cable ................................................................................................................ 17

2.3.5 RS-232 Cable ........................................................................................................................ 18

2.4 CONNECTOR PIN ASSIGNMENT ............................................................................................................ 18

2.4.1 Connectors Guide ................................................................................................................. 19

2.5 I/O SIDE ......................................................................................................................................... 34

CHAPTER 3 USING THE LCD MONITOR .............................................................................................. 40

3.1 OSD KEY FUNCTIONS ........................................................................................................................ 40

3.2 OSD MENU NAVIGATION ................................................................................................................... 41

3.2.1 Display .................................................................................................................................. 42

3.2.2 Adjust ................................................................................................................................... 43

3.2.3 Audio .................................................................................................................................... 44

3.2.4 Multi-Display ........................................................................................................................ 44

User Manual VIII

3.2.5 OSD....................................................................................................................................... 45

3.2.6 Advanced .............................................................................................................................. 46

CHAPTER 4 TROUBLESHOOTING ....................................................................................................... 49

APPENDIX A SUPPORTED MODES .................................................................................................... 51

APPENDIX C REMOTE CONTROL SET COMMAND ............................................................................. 57

APPENDIX D REMOTE CONTROL GET COMMAND ............................................................................ 63

APPENDIX E ELECTRICAL CHARACTERISTICS ..................................................................................... 69

R2AP Panel Control Board General Information

User Manual 9

General Information This chapter includes the R2AP panel control board background information.


User Manual 10

Chapter 1 General Information

This chapter includes the R2AP Panel Control Board background information.

1.1 Introduction

Thank you for choosing R2AP Panel Control Board. The Winmate R2AP is a

powerful graphic processing board, providing High quality images for TFT panels

from VGA (640 x 480) up to DCI 4K (4096 x 2160) and can be used in a variety of

systems. The R2AP provides all A/D board key functions required for image capture,

processing and display timing control, other functions include PIP / PBP – 4P function,

Image rotation (90, 180, 270 deg.), OSD rotation (90,270 deg.), and programmable

12-bit LUT.

With all these functions integrated onto a single board, the R2AP is able to keep

up with the cost of high-end multimedia LCD monitors while maintaining a high

degree of flexibility and quality. It is suitable for large size and high resolution panels

and meets the demanding performance requirements of today’s business and

industrial applications. A single board reduces the costs of high-end multimedia LCD

monitors, meanwhile maintaining high degree of flexibility and quality.

1.2 Features

Support high resolution up to 4096 x 2160 @ 60Hz.

Support multiple panel interface including 10-bit LVDS, V-by-One and eDP.

Content protection HDCP 1.4 is supported with HDMI.

VGA support Sync-On-Green (SOG) and composite mode.

RS-232 remote control by user operation.

With IR remote control.

12/24V input (with jumper setting).

Operating temperature 0 to 60°C.

Storage temperature -10 to 60° C.


User Manual 11

1.3 Hardware Specifications

System Specification:

Scaler RTD2796B-CG

Internal Connector:

To Backlight Unit Wafer

IR Sensor Wafer

GPIO Reserved

I2C Reserved

OSD Key Pad Wafer

5V 5V / 1A Output wafer

12V 12V / 1A Output wafer

Output Interface (internal):

LVDS Hirose-DF13DP-1.25V

V-By-One V-by-One Output Connector

eDP Hirose-DF13DP-1.25V

Input Signal:

DVI-D Dual Link DVI-D

HDMI1.4 Type A

HDMI2.0 Type A

Display Port1.2 Display Port1.2

VGA D-Sub 15Pin

Audio Line In 3.5mm Stereo Input

Audio In /Out:

Speaker Output 8W, class D

Power Requirements:

Power Input Din 4 Pin (12V / 24V setting by jumper)

(*Default 12V)

Power Output Wafer

Mechanical:

Dimensions (W x H x D) 167 x 120mm

Environment:

Operating Temperature 0°~+60°C

Storage Temperature -10°~+60°C

Operating Humidity 30%~ 90% (non-condensing, RH)


User Manual 12

Certification:

Electromagnetic CE, FCC

1.4 Functional Description

Function block(V110)


User Manual 13

1.5 Physical Description

Board Dimensions (V110)

R2AP Panel Control Board Hardware Installation

User Manual 14

Hardware Installation This chapter provides information on how to use

jumpers and connectors on the R2AP panel control

board.


User Manual 15

Chapter 2 Hardware Installation

This chapter provides information on how to use jumpers and connectors on the

R2AP control board. Be cautious while working with these modules. Carefully read

the content of this chapter in order to avoid any damages.

2.1 Motherboard Components

2.1.1 Front Side


User Manual 16

2.1.2 Rear Side

2.1.3 I/O Side

NOTE:

Some connectors are optional depends on your order.

SW1

USB 2.0

Mini-PCIE

Half Card


User Manual 17

2.2 I/O Equipment Installation

This chapter provides information on how to use jumpers and connectors on the

R2AP A/D Board. Be cautious while working with these modules. Please carefully

read the content of this chapter in order to avoid any damages.

2.2.1 Power

Switch off the power on the monitor and the Keypad. The power switch is located at

the most right button of the keypad.

2.2.2 Power Cable

Connect the power cord to monitor, and then connect the power to the AC outlet

through the AC/DC adapter.

2.3 Options

The R2AP panel control port is designed for monitors that work with a variety of

compatible video sources. Due to the possible deviations between these signal

sources, you may have to make adjustments to the monitor settings from the OSD

menu when switching between these sources.

2.3.1 VGA Cable

Plug 15-pin VGA signal cable to the VGA connector in the rear of motherboard, and

plug the other end to the monitor. Secure cable connectors with hexagonal copper

pillars M3x4mm.

2.3.2 DVI-D Cable

Plug in DVI-D signal cable to the DVI-D connector on the rear side of the

motherboard, and plug in the other end to the monitor. Secure cable connectors

with hexagonal copper pillars M3x4mm.

2.3.3 HDMI Cable

Plug HDMI signal cable to the HDMI connector on the rear side of PC system, and

plug the other end to the monitor. Secure cable connectors hexagonal copper pillars

M3x4mm.

2.3.4 Display Port Cable

Plug display port signal cable to the Display port connector on the rear side of PC

system, and plug in the other end to the monitor. Secure cable connectors with


User Manual 18

hexagonal copper pillars M3x4mm.

2.3.5 RS-232 Cable

You will be able to develop your own application software utilizing built-in RS-232

command code. The application software can send command from PC to LCD

monitor via RS-232 port to control LCD monitor. Please refer to Appendix B for

built-in RS-232 command code.

2.4 Connector Pin Assignment

This section explains how to set jumpers for correct configuration of the

motherboard.

NOTE:

A pair of needle nose pliers may be helpful when working with jumpers.

If you have any doubts about the best hardware configuration for your

application, contact your local distributor or sales representative before

you make any changes. Generally, you simply need a standard cable to

make most connections.

The jumper setting diagram is shown below. When the jumper cap is placed on both

pins, the jumper is SHORT. The illustration below shows a 3-pin jumper; pins 1 and 2

are short. If you remove the jumper cap, the jumper is OPEN.

1

2

3


User Manual 19

2.4.1 Connectors Guide

The table below shows each of front side connectors and its functions.

Connector Function Note

CN3 VGA Input Wafer JST-B13B-PH-K-S or equivalent

CN9 OSD Key Pad Wafer 1*10p P=2.0mm DIP 180°

CN12 Stereo Line Output Wafer 6p P:1.0mm SMD 180° white

CNF1 V-by-One Output Connector FI-RESIS-HF 51p JAE

J5 Speaker Output JST-B4B-PH-K-S or equivalent.

J6 LVDS output- A Hirose-DF13DP-1.25V

J7 To Backlight Unit JST-B7B-PH-K-S or equivalent

J8 LVDS output- B Hirose-DF13DP-1.25V

J9 Panel Power Selector Header 2*3p P:2.54mm DIP 180°

J10 LVDS output- C Hirose-DF13DP-1.25V

J11 LVDS output- D Hirose-DF13DP-1.25V

J12 IR Sensor JST-B3B-PH-K-S or equivalent

J14 GPIO JST-B3B-PH-K-S or equivalent.

J15 I2C JST-B4B-PH-K-S or equivalent.

J16 Power Din 4 Pin Input Power Jack Din 4p dip Quick Lock

J17 Power Wafer Input 2.0mm 2 x 6 Pin Header DIP180°

J18 Power Wafer Output JST-B20B-PHDSS or equivalent

J19 12V/1A Output JST-B2B-PH-K-S or equivalent

J20 5V/1A Output JST-B2B-PH-K-S or equivalent

J21 3.3V/1A Output JST-B2B-PH-K-S or equivalent

J22 eDP Output Wafer Hirose-DF13DP-1.25V

J24 UART Wafer 2.54mm 1 x 4 pin header

J25 GPIO JST-B3B-PH-K-S or equivalent

JP2 Hanns (10.1”) (optional

connector)

Header 1*3p P=2.00mm DIP 180°

JP5 24V/12V Selector for Power

Input

Header 2*4p P:2.54mm DIP 180°

JP6 DC/PWM Select Connector Header 1*3p P:2.54mm DIP 180°

JP7 12V/5V Selector for BLU Power Header 2*4p P:2.54mm DIP 180°

JP8 PWM Level(5V/3.3V)Select

Connector

Header 1*3p P=2.00mm DIP 180°


User Manual 20

CN3:VGA Input Wafer

Pin No. Description

1 Red+

2 Red-

3 Green+

4 Green-

5 Blue+

6 Blue-

7 SDA

8 HS

9 VS

10 Cable Detect

11 SCL

12 GND

13 VGA 5V

CN9: OSD Key Pad Wafer

Pin No. Symbol Description

1 PWR Power LED

2 PWR_SW Power on/off control

3 - Right key

4 > Increase

5 < Decrease

6 NC No connection

7 + Left key

8 STB Standby LED

9 GND Ground

10 +5V DC 5V


User Manual 21

CN12: Stereo Line Output

CNF1: V-by-One Output Connector


1 GND Ground

2 TX7P Positive V-by-One differential data output Lane 7

3 TX7N Negative V-by-One differential data output Lane 7

4 GND Ground



7 GND Ground



10 GND Ground



13 GND Ground



16 GND Ground



19 GND Ground


Pin No. Description

1 LINEOUT_DET

2 AUD_R1_OUT

3 RINP

4 LINP

5 AUD_L1_OUT

6 GND


User Manual 22


22 GND Ground



25 GND Ground

26 LOCKN Lock detect input

27 HTPDN Hot plug detect input

28 8b_10b 8bit /10bit Select

29 NC No Connection

30 LD_EN Local Dimming Mode Enable

31 2nd AUX_P 2ndAUX_P

32 2nd AUX_N 2ndAUX_N

33 SCL I2C Clock signal

34 SDA I2C Data signal

35 2D3D 2D/3D Enable

36 LR Input signal for Glasses Left Right signal

37 LRI Output signal for Left/Right synchronous signal

38 1st AUX_P 1st AUX_P

39 1st AUX_N 1st AUX_N

40 GND Ground

41 GND Ground

42 GND Ground

43 NC No Connection

44 PNL_PWR Power output (+12V)









User Manual 23

J5: Speaker Output

J6: Bits LVDS output- A

Pin No. Symbol

1 LOUT+

2 LOUT-

3 ROUT-

4 ROUT+


1 PWR Panel power

2 ATX0- LVDS negative A bit 0

3 PWR Panel power

4 ATX0+ LVDS positive A bit 0

5 NC Not Connect


7 GND Ground


9 SDA I2C SDA


11 SCL I2C SCL


13 GND Ground

14 ACLKTX- LVDS negative A clock

15 GND Ground

16 ACLKTX+ LVDS positive A clock





21 GND Ground

22 BTX0- LVDS negative B bit 0


User Manual 24

J7: To Backlight Unit

23 BTRL1 Optional

24 BTX0+ LVDS positive B bit 0

25 BTRL2 Optional


27 BTRL3 Optional


29 BTRL4 Optional


31 BTRL5 Optional


33 GND Ground

34 BCLKTX- LVDS negative B clock

35 GND Ground

36 BCLKTX+ LVDS positive B clock

37 BTX4- LVDS negative Bbit 4

38 BTX3- LVDS negative Bbit 3


40 BTX3+ LVDS positive Bbit 3

Pin No. Symbol

1 +12V

2 +12V

3 +12V

4 GND

5 ADJ

6 GND

7 ON/OFF


User Manual 25

J8: Bits LVDS Output- B


1 PWR Panel power

2 DTX0- LVDS negative D bit 0

3 PWR Panel power

4 DTX0+ LVDS positive D bit 0

5 NC Not Connect


7 GND Ground


9 GND Ground


11 GND Ground


13 GND Ground

14 DCLKTX- LVDS negative D clock

15 GND Ground

16 DCLKTX+ LVDS positive D clock





21 GND Ground

22 CTX0- LVDS negative C bit 0

23 GND Ground

24 CTX0+ LVDS positive C bit 0

25 GND Ground


27 GND Ground


29 GND Ground



User Manual 26

31 GND Ground


33 GND Ground

34 CCLKTX- LVDS negative C clock

35 GND Ground

36 CCLKTX+ LVDS positive C clock





J9: Panel Power Selector

Pin No. Description

1-2 Short pin 1-2 to set +3.3V

3-4 Short pin 3-4 to set +5V

5-6 Short pin 5-6 to set +12V

J10: Bits LVDS output- C


1 PWR Panel power

2 ETX0- LVDS negative E bit 0

3 PWR Panel power

4 ETX0+ LVDS positive E bit 0

5 NC Not Connect


7 GND Ground


User Manual 27


9 SDA I2C SDA


11 SCL I2C SCL


13 GND Ground

14 ECLKTX- LVDS negative E lock

15 GND Ground

16 ECLKTX+ LVDS positive E clock





21 GND Ground

22 FTX0- LVDS negative F bit 0

23 FTRL1 Optional

24 FTX0+ LVDS positive F bit 0

25 FTRL2 Optional


27 FTRL3 Optional


29 FTRL4 Optional


31 FTRL5 Optional


33 GND Ground

34 FCLKTX- LVDS negative F clock

35 GND Ground

36 FCLKTX+ LVDS positive F clock

37 FTX4- LVDS negative Fbit 4

38 FTX3- LVDS negative Fbit 3


40 FTX3+ LVDS positive Fbit 3


User Manual 28

J11: Bits LVDS output- D


1 PWR Panel power

2 GTX0- LVDS negative G bit 0

3 PWR Panel power

4 GTX0+ LVDS positive G bit 0

5 NC Not Connect


7 GND Ground


9 GND Ground


11 GND Ground


13 GND Ground

14 GCLKTX- LVDS negative G clock

15 GND Ground

16 GCLKTX+ LVDS positive G clock





21 GND Ground

22 HTX0- LVDS negative H bit 0

23 GND Ground

24 HTX0+ LVDS positive H bit 0

25 GND Ground

26 HTX1- LVDS negative H bit 1

27 GND Ground


29 GND Ground

30 HTX2- LVDS negativeH bit 2


User Manual 29

31 GND Ground


33 GND Ground

34 HCLKTX- LVDS negative H clock

35 GND Ground

36 HCLKTX+ LVDS positive H clock

37 HTX4- LVDS negative Hbit 4

38 HTX3- LVDS negative Hbit 3


40 HTX3+ LVDS positive Hbit 3

J12: IR Sensor

J14: GPIO

J15: I2C

Pin No. Symbol

1 IR

2 GND

3 +5V

Pin No. Symbol

1 +5V

2 GND

3 GPIO

Pin No. Symbol

1 +5V

2 SDA

3 SCL

4 GND


User Manual 30

J17: Power Wafer Input

J18: Power Wafer Output

Pin No. Symbol

1 +12V/+24V

2 +12V/+24V

3 +12V/+24V

4 +12V/+24V

5 +12V/+24V

6 +12V/+24V

7 +12V/+24V

8 +12V/+24V

9 +12V/+24V

10 +12V/+24V

11 GND

12 GND

13 GND

14 GND

15 GND

16 GND

17 GND

Pin No. Symbol

1 +12V/+24V

2 +12V/+24V

3 +12V/+24V

4 +12V/+24V

5 +12V/+24V

6 +12V/+24V

7 GND

8 GND

9 GND

10 GND

11 GND

12 GND


User Manual 31

18 GND

19 GND

20 GND

J19: 12V/1A Output

J20: 5V/1A Output

J21: 3.3V/1A Output

Pin No. Symbol

1 +12V

2 GND

Pin No. Symbol

1 +5V

2 GND

Pin No. Symbol

1 +3.3V

2 GND


User Manual 32

J22: eDP Output Wafer

Pin No. Symbol Pin No. Symbol

1 AUXN 2 SCL

3 AUXP 4 SDA

5 GND 6 HDMI_MHL

7 L3N 8 DP

9 L3P 10 HDMI_MHL

11 GND 12 TX_HDD

13 L2N 14 GND

15 L2P 16 GND

17 GND 18 GND

19 L1N 20 GND

21 L1P 22 PWR

23 GND 24 PWR

25 L0N 26 PWR

27 L0P 28 PWR

29 GND 30 +3.3V_DP

J24: UART Wafer

J25: Reserved GPIO


1 +5V +5V

2 TXD UART Transmit Signal

3 RXD UART Receive Signal

4 GND Ground

Pin No. Description

1 GPIO

2 GPIO

3 GPIO

4 GPIO


User Manual 33

JP2: Hanns (10.1”) Optional Connector

JP5: Selector for Power Input 24V/ 12V

Pin No. Description

1-2 , 3-4 24V

5-6 , 7-8 12V (default)

JP6: Brightness Control (PWM or DC control)

Pin No. Description

1-2 Hannstar(10.1”) Connector

2-3 Normal Connector

Pin No. Description

1-2 DC voltage

2-3 PWM signal


User Manual 34

JP7: Selector for BLU Power 12V/ 5V

Pin No. Description

1-2 , 3-4 12V

5-6 , 7-8 5V

JP8: Adjust PWM Level (5V/3.3V) Connector

2.5 I/O Side

The table below shows each of I/O side connectors and its functions.

Connector Description

CN2 DVI-D input

CN4 Display port input

CN7 HDMI 2.0 input

J3 Audio-in, 3.5mm stereo input

U9 VGA D-Sub 9 input

CN15 HDMI 1.4 input


1-2 PWM_5V PWM 5V Connector

2-3 PWM_3V3 PWM 3.3V Connector


User Manual 35

CN2: DVI-D

CN4: Display Port Input

Pin № Symbol Pin № Symbol

1 DVI_RX2- 2 DVI_RX2-

3 GND 4 4-

5 4+ 6 DVI SCL

7 DVI SDA 8 NC

9 DVI_RX1- 10 DVI_RX1+

11 GND 12 3-

13 3+ 14 +5V

15 DVI_CON_CABLE 16 DVI_CON_HP

17 DVI_RX0- 18 DVI_RX0+

19 GND 20 5-

21 5+ 22 GND

23 DVI_CLKP 24 DVI_CLKN

C1 NC C2 NC

C3 NC C4 NC

C5 NC

Pin № Name Pin № Name

1 Lane 0 2 GND

3 Lane 0 4 Lane 1

5 GND 6 Lane 1

7 Lane 2 8 GND

9 Lane 2 10 Lane 3

11 GND 12 Lane 3

13 GND 14 Lane 3

15 AUX 16 GND

17 AUX 18 Hot Plug

19 Return 20 DP_PWR


User Manual 36

CN7: HDMI 2.0

J3: Audio-in

Pin No. Description

1 HDMI_RX2+

2 GND

3 HDMI_RX2-

4 HDMI_RX1+

5 GND

6 HDMI_RX1-

7 HDMI_RX0+

8 GND

9 HDMI_RX0-

10 HDMI_RXC+

11 GND

12 HDMI_RXC-

13 HDMI_CON_CEC

14 NC

15 HDMI_CON_SCL

16 HDMI_CON_SDA

17 HDMI_CON_CABLE

18 +5V_HDMI

19 HDMI_CON_HP

Pin № Symbol

1 GND

2 LINE_IN_L

3 NC

4 LINE_IN_R

5 NC


User Manual 37

U9: VGA D-Sub 9

CN15: HDMI 1.4 Input


1 RED 2 GREEN

3 BLUE 4 NC

5 GND 6 RED_RTN

7 GREEN_RTN 8 BLUE_RTN

9 KEY/PWR 10 GND

11 NC 12 SDA

13 H Sync 14 V Sync

15 SCL

Pin No. Description

1 HDMI_RX2+

2 GND

3 HDMI_RX2-

4 HDMI_RX1+

5 GND

6 HDMI_RX1-

7 HDMI_RX0+

8 GND

9 HDMI_RX0-

10 HDMI_RXC+

11 GND

12 HDMI_RXC-

13 HDMI_CON_CEC

14 NC

15 HDMI_CON_SCL

16 HDMI_CON_SDA

17 HDMI_CON_CABLE

18 +5V_HDMI

19 HDMI_CON_HP


User Manual 38

DC Input: Power 24/12V In


1 DC_IN 2 GND

3 DC_IN 4 GND

R2AP Panel Control Board Using the LCD Monitor

User Manual 39

Using the LCD Monitor This chapter contains operating LCD monitor

guide. You can find OSD key definitions and

menu navigation in this chapter.


User Manual 40

Chapter 3 Using the LCD Monitor

This chapter contains operating LCD monitor guide. You can find OSD key

definitions and menu navigation in this chapter.

3.1 OSD Key Functions

Icon Function

Decrease the value / Select up or down

Increase the value / Select up or down

Power switch

Select left

Select right / Call main OSD menu


User Manual 41

3.2 OSD Menu Navigation


User Manual 42

3.2.1 Display

OSD Icon Sub menu Settings Note

BRIGHTNESS slider bar

Adjusts the overall image and background brightness. Press “ ” or “ ” to adjust.

CONTRAST slider bar

Adjusts the image brightness in relationship to the background. Press“ ” or “ ” to

adjust.

SHARPNESS slider bar

Adjusts the crispness of the image. Press“ ” or “ ” to adjust.

ADC BRIGHTNESS

*VGA CHANNEL ONLY slider bar

Adjusts the ADC brightness. Press“ ” or “ ” to adjust.

TEMPERATURE USER/ sRGB/ 6500K/ 9300K

Adjusts the color temperature of the entire screen. A low color temperature will

make the screen reddish. A high color temperature will make the screen bluish.

COLOR CONTROL

R slider bar

G slider bar

B slider bar

Adjusts the levels of the Red, Green, Blue. Press“ ” or “ ” to adjust.

GAMMA SELECTION

OFF

1.8

2.2

Select a display gamma value for best picture quality.

SCHEME

USER

Standard

GAME

SPORT

Movie

Photo

Select scheme for different default setting combination.

HUE slider bar

Saturation slider bar

Region 1P

1/2P,2/2P,1+2/2P


User Manual 43

1/4P,2+3+4/4P

2/4P, 1+3+4/4P

3/4P, 1+2+4/4P

4/4P,1+2+3/4P,1+2+3+4/4P

3.2.2 Adjust

Adjust

Auto Adjust

*VGA CHANNEL ONLY Yes/No

Automatically adjusts screen size, H position, V position, Clock, Clock Phase

AUTO Setting

*VGA CHANNEL ONLY OFF/ON

H Position, V Position and Clock Phase are adjusted automatically upon power on.

H POSITION


Controls the horizontal position of the image within the Display area of the LCD.

Press + to move right. Press - to move left.

V POSITION


Controls the vertical position of the image within the Display area of the LCD.

Press + to move up. Press - to move down.

CLOCK


Press + to expand the width of the image on the right of the screen.

Press - to narrow the width of the image on the left.

PHASE


Adjusts the visual “noise” on the image.

WHITE BALANCE

*VGA CHANNEL ONLY YES/OFF

Perform the white balance


User Manual 44

3.2.3 Audio

`

VOLUME slider bar

Adjusts the Volume. Press“ ” or “ ” to adjust.

MUTE ON/OFF

Audio Source Analog/1P/2P/3P/4P

3.2.4 Multi-Display

Display Mode

1P

1/2P Right Left

1/2P Up down

PIP

4P

Choose the Display Mode for 1P , 2P , 4P

Display source Select 1 2 3 4

Auto scan

VGA

DVI

HDMI 2.0

HDMI 1.4

DP

Choose the channel of Display source

2P LR Ratio

Ratio 0

Ratio 1

Ratio 2

Ratio 3

Ratio 4

PIP Size slider bar

Adjust the Picture-in-Picture( PIP) Size

PIP Position Horizontal

Vertical

Determines where the PIP appears on the screen.

Multi Display SWAP YES/NO


User Manual 45

3.2.5 OSD

OSD TURN OFF slider bar

Turns off the OSD after a period of inactivity. The preset choices are 10-60 seconds.

OSD POSITION Horizontal - slider bar

Vertical - slider bar

Determines the location where the OSD appears on the screen.

OSD TRANSPARENCY slider bar

Adjusts the transparency level of OSD

OSD Rotated

@OFF

@90

@270

Set to rotate the OSD menu

MONITOR INFORMATION

Version

Input 1 Source

Resolution

Input 2 Source

Resolution

Input 3 Source

Resolution

Input 4 Source

Resolution

Shows BIOS version & resolution info.


User Manual 46

3.2.6 Advanced

Scaling

Full Screen

16:9

4:3

5:4

1:1

Adjust the image scaling setting

Flip

ROTATE 0

ROTATE 90

ROTATE 0 180

ROTATE 0 270

Up down

Left Right

Scan Type Under Scan

Over Scan

Choose the scan type

Color Format RGB

YUV

Choose the format of color composition

Scheme RED HUE - slider bar

Saturation - slider bar

Scheme Green HUE - slider bar


Scheme Blue HUE - slider bar


Scheme Yellow HUE - slider bar


Scheme Magenta HUE - slider bar


Scheme Cyan HUE - slider bar


Brightness Min 0 to 10 Stratum

Factory rest Yes/No


User Manual 47

Resets OSD options back to factory settings EXCEPT FOR: CHANGE SECURITY

PASSWORD and SECURITY PASSWORD.

R2AP Panel Control Board Troubleshooting

User Manual 48

Troubleshooting This chapter contains troubleshooting information.

Check this guide before calling for repairs.

R2AP Panel Control Board Troubleshooting

User Manual 49

Chapter 4 Troubleshooting

If your monitor fails to operate correctly, check the following chart for possible

solution before calling for repairs:

Condition Check Point

1. The picture does not

appear

Check if the signal cable is firmly seated in the socket.

Check if the Power is ON at the computer

Check if the brightness control is at the appropriate position,

not at the minimum.

2. The screen is not

synchronized

Check if the signal cable is firmly seated in the socket.

Check if the output level matches the input level of your

computer.

Make sure the signal timings of the computer system are

within the specification of the monitor.

If your computer was working with a CRT monitor, you

should check the current signal timing and turn off your

computer before you connect the VGA Cable to this monitor.

3. The position of the

screen is not in the

center

Adjust the H-position, and V-position, or Perform the Auto

adjustment.

4. The screen is too

bright (too dark).

Check if the brightness or contrast control is at the

appropriate position, not at the Maximum (Minimum).

5. The screen is shaking

or waving

Perform the Auto adjustment.

Moving all objects which emit a magnetic field such as motor

or transformer, away from the monitor.

Check if the specific voltage is applied.

Check if the signal timing of the computer system is within

the specification of monitor.

6. VGA signal got noise

when using PIP

function

Change PIP mode again.

*If you are unable to correct the fault by using this chart, stop using your monitor and

contact your distributor or dealer for further assistance

R2AP Panel Control Board Appendices

User Manual 50

Supported Modes This section includes supported modes. The

choice of supported modes depends on the

monitor native resolution.

Appendix


User Manual 51

Appendix A Supported Modes

The choice of supported modes depends on the monitor native resolution.

DVI

No. Resolution Frequency

(Hz)


(Hz)

1 640x350 70 21 1024x768 85

2 640x350 85 22 1280x768 60

3 640x400 56 23 1280x960 60

4 640x400 70 24 1280x960 85

7 640x480 75 25 1280x1024 60

8 640x480 80 26 1280x1024 60

9 720x350 70 27 1280x1024 67

10 720x400 70 28 1280x1024 70

11 720x400 85 29 1280x1024 72

12 800x600 56 30 1280x1024 75

13 800x600 60 31 1280x1024 85

14 800x600 72 32 1600x1200 60

15 800x600 75 33 1920x1200 60

16 800x600 85 34 1366x768 60

17 1024x768 60 35 1920x1080 60

18

1024x768 70

36 2560x1440

(DVI dual

link only)

60

19

1024x768 72

37 2560x1600

(DVI dual

link only)

60

20

1024x768 75

38 3840 x

2160

(DVI dual

link only)


User Manual 52

VGA

No. Resolution Frequency (Hz)

1 640x480 67

2 640x480 72

3 640x480 75

4 640x480 80

5 720x400 70

6 800x600 56

7 800x600 60

8 800x600 72

9 800x600 75

10 1024x768 60

11 1024x768 70

12 1024x768 72

13 1024x768 75

14 1024x768 75

15 1280x1024 60

16 1280x1024 75

17* 1600x1200 60

18* 1680x1050 60

19* 1920x1200 60

20* 1366x768 60

21* 1920x1080 60


User Manual 53

HDMI 1.4


(Hz)

1 640x480 60

2 640x480 72

3 640x480 75

4 800x600 60

7 800x600 72

8 800x600 75

9 1024x768 60

10 1024x768 70

11 1024x768 75

12 1280x768 60

13 1280x1024 60

14 1280x1024 75

15 1366x768 60

16 1400x1050 60

17 1440x900 60

18 1600x900 60

19 1600x1200 60

20 1680x1050 60

21 1920x1080 60

22 1920x1200 60

24 2560x1600 60

25 3840x2160 30


User Manual 54

HDMI 2.0


(Hz)

1 640x480 60

2 640x480 72

3 640x480 75

4 800x600 60

7 800x600 72

8 800x600 75

9 1024x768 60

10 1024x768 70

11 1024x768 75

12 1280x768 60

13 1280x1024 60

14 1280x1024 75

15 1366x768 60

16 1400x1050 60

17 1440x900 60

18 1600x900 60

19 1600x1200 60

20 1680x1050 60

21 1920x1080 60

22 1920x1200 60

24 2560x1600 60

25 3840x2160 60

26 4096x2160 60


User Manual 55

Display port 1.2


(Hz)

1 640x480 60

2 640x480 72

3 640x480 75

4 800x600 60

7 800x600 72

8 800x600 75

9 1024x768 60

10 1024x768 70

11 1024x768 75

12 1280x768 60

13 1280x1024 60

14 1280x1024 75

15 1366x768 60

16 1400x1050 60

17 1440x900 60

18 1600x900 60

19 1600x1200 60

20 1680x1050 60

21 1920x1080 60

22 1920x1200 60

24 2560x1600 60

25 3840x2160 30

26 3840x2160 60

27 4096x2160 60


User Manual 56

Remote Control Set Command This section includes remote control set

command.

Appendix


User Manual 57

Appendix C Remote Control Set Command

Name Length Value Comment

Message Variable

Checksum 1 2's complement of

sum of Length and

Message

byte chksum = 0;

for ( i = 0; i<buffer_size; ++i )

chksum += buf[i];

chksum = ~chksum + 1;

No Function Length Command Index Value Checksum(*1) Remark

1 Auto 0x05 0x40 0x01 0=Auto 0xBA=Auto

2 Recall 0x05 0x40 0x02 0=Recall 0xB9=Recall

3 White Balance 0x05 0x40 0x03 0=White

Balance

0xB8=White

Balance

4 1P Input

Source 0x05 0x40 0x04

0x00=VGA

0x01=DVI

0x07=HDMI 2.0

0x08=DP

0x17=HDMI 1.4

0xB7=VGA

0xB6=DVI

0xB0=HDMI 2.0

0xAF=DP

0xA0= HDMI 1.4

5 2P Input


0x00=VGA

0x01=DVI

0x07=HDMI 2.0

0x08=DP

0x17=HDMI 1.4

0xB6=VGA

0xB5=DVI

0xAF=HDMI 2.0

0xAE=DP

0x9F= HDMI 1.4

6 3P Input


0x00=VGA

0x01=DVI

0x07=HDMI 2.0

0x08=DP

0x17=HDMI 1.4

0xB5=VGA

0xB4=DVI

0xAE=HDMI 2.0

0xAD=DP

0x9E= HDMI 1.4

7 4P Input


0x00=VGA

0x01=DVI

0x07=HDMI 2.0

0x08=DP

0x17=HDMI 1.4

0xB4=VGA

0xB3=DVI

0xAD=HDMI 2.0

0xAC=DP

0x9D= HDMI 1.4

8 Display Mode 0x05 0x40 0x08 0x00 Mode 1P

0x01 Mode 2P

0xB3 Mode 1P

0xB2 Mode 2P


User Manual 58

(L/R)

0x02 Mode 2P

(T/B)

0x03 Mode 2P

(M/S)

0x04 Mode 4P

(L/R)

0xB1 Mode 2P

(T/B)

0xB0 Mode 2P

(M/S)

0xAF Mode 4P

9 Region 0x05 0x40 0x09

0x00 1P

0x01 2P LR Left

0x02 2P LR

Right

0x03 2P LR Full

0x04 2P TB Top

0x05 2P TB

Button

0x06 2P TB Full

0x07 2P PIP

Main

0x08 2P PIP

Sub

0x09 2P PIP

Full

0x0A 4P LT

Inside

0x0B 4P LT

Outside

0x0C 4P LB

Inside

0x0D 4P LB

Outside

0x0E 4P RT

Inside

0x0F 4P RT

Outside

0x10 4P RB

Inside

0x11 4P RB

Outside

0x12 4P Full

0xB2 1P

0xB1 2P LR Left

0xB0 2P LR Right

0xAF 2P LR Full

0xAE 2P TB Top

0xAD 2P TB

Button

0xAC 2P TB Full

0xAB 2P PIP Main

0xAA 2P PIP Sub

0xA9 2P PIP Full

0xA8 4P LT Inside

0xA7 4P LT

Outside

0xA6 4P LB Inside

0xA5 4P LB

Outside

0xA4 4P RT Inside

0xA3 4P RT

Outside

0xA2 4P RB Inside

0xA1 4P RB

Outside

0xA0 4P Full


User Manual 59

10 Brightness 0x05 0x40 0x10 0x00~0x64 0xAB=0 ~

0x47=100

11 Contrast 0x05 0x40 0x11 0x00~0x64 0xAA=0 ~

0x46=100

Region

12 Hue 0x05 0x40 0x12 0x00~0x64 0xA9=0 ~

0x45=100

Region

13 Saturation 0x05 0x40 0x13 0x00~0x64 0xA8=0 ~

0x44=100

Region

14 ADC

Brightness 0x05 0x40 0x14 0x00~0x64

0xA7=0 ~

0x43=100

Region

15 Sharpness 0x05 0x40 0x15 0x00~0x04 0xA6=0 ~ 0xA2=4 Region

16 Gamma 0x05 0x40 0x31

0=Native

1=Gamma 1.8

2=Gamma 2.2

0x8A= Native

0x89=Gamma 1.8

0x88=Gamma 2.2

Region

17 Color Temp 0x05 0x40 0x32

0=user

1=9300K

2=6500K

3=sRBG

0x89=User

0x88=9300K

0x87=6500K

0x86=sRGB

Region

18 Color-R 0x05 0x40 0x33 0x00-0x64 0x88=0 ~

0x24=100

Region

19 Color-G 0x05 0x40 0x34 0x00-0x64 0x87=0 ~

0x23=100

Region

20 Color-B 0x05 0x40 0x35 0x00-0x64 0x86=0 ~

0x22=100

Region

21 SCHEME 0x05 0x40 0x36

0=Standard

1=GAME

2=MOVIE

3=PHOTO

4=VIVID

5=USER

0x85=Standard

0x84=GAME

0x83=MOVIE

0x82=PHOTO

0x81=VIVID

0x80=USER

Region

22 Volume 0x05 0x40 0x50 0x00~0x64 0x6B=0~0x07=100

23 Mute 0x05 0x40 0x54 0=OFF

1=ON

0x67=OFF

0x66=ON

24 Audio Source 0x05 0x40 0x55

0=Analog

1=1P

2=2P

3=3P

4=4P

0x66=Analog

0x65=1P

0x64=2P

0x63=3P

0x62=4P


User Manual 60

25 LR RATIO 0x05 0x40 0x70

0=RATIO 0

1=RATIO 0

2=RATIO 0

3=RATIO 0

4=RATIO 0

0x4B=RATIO 0

0x4A=RATIO 0

0x49=RATIO 0

0x48=RATIO 0

0x47=RATIO 0

26 PIP SIZE 0x05 0x40 0x71 0x00~0x0A 0x4A=0~0x40=10

27 FLIP 0x05 0x40 0x80

0=ROTATE 0

1=ROTATE 90

2=ROTATE 180

3=ROTATE 270

4=H MIRROR

5=V MIRROR

0x3B=ROTATE 0

0x3A=ROTATE 90

0x39=ROTATE 180

0x38=ROTATE 270

0x37=H MIRROR

0x36=V MIRROR

28 SCALING 0x05 0x40 0x81

0=FULL

1=16:9

2=4:3

3=5:4

4=1:1

0x3A=FULL

0x39 =16:9

0x38 =4:3

0x37 =5:4

0x36 =1:1

Region

29 SCHEME Red

Hue 0x05 0x40 0x82 0x00~0x64 0x39=0~0xD5=100

Region

30 SCHEME Red

Sat 0x05 0x40 0x83 0x00~0x64 0x38=0~0xD4=100

Region

31 SCHEME

Green Hue 0x05 0x40 0x84 0x00~0x64 0x37=0~0xD3=100

Region

32 SCHEME

Green Sat 0x05 0x40 0x85 0x00~0x64 0x36=0~0xD2=100

Region

33 SCHEME Blue

Hue 0x05 0x40 0x86 0x00~0x64 0x35=0~0xD1=100

Region

34 SCHEME Blue

Sat 0x05 0x40 0x87 0x00~0x64 0x34=0~0xD0=100

Region

35 SCHEME

Yellow Hue 0x05 0x40 0x88 0x00~0x64 0x33=0~0xCF=100

Region

36 SCHEME

Yellow Sat 0x05 0x40 0x89 0x00~0x64 0x32=0~0xCE=100

Region

37 SCHEME

Magenta Hue 0x05 0x40 0x8A 0x00~0x64 0x31=0~0xCD=100

Region

38 SCHEME

Magenta Sat 0x05 0x40 0x8B 0x00~0x64 0x30=0~0xCC=100

Region

39 SCHEME Cyan 0x05 0x40 0x8C 0x00~0x64 0x2F=0~0xCB=100 Region


User Manual 61

Hue

40 SCHEME Cyan

Sat 0x05 0x40 0x8D 0x00~0x64 0x2E=0~0xCA=100

Region


User Manual 62

Remote Control Get Command This section includes remote control get

command.

Appendix


User Manual 63

Appendix D Remote Control Get Command

Name Length Value Comment

Message variable

Checksum 1 2’s complement of sum of

Length and Message

byte chksum = 0;

for ( I = 0; I

<buffer_size; ++I )

chksum += buf[i];

chksum = ~chksum

+ 1;

Command(Tx) Acknowledgement(Rx)

Function Length Command Index Checksu

m

Leng

th

Inde

x Value Checksum

1P Input

Source 0x04 0x30 0x04 0xC8 0x04 0x04

0x00=VGA

0x01=DVI

0x07=HD

MI 2.0

0x08=DP

0x17=HD

MI 1.4

0xF8=VGA

0xF7=DVI

0xF1=HDMI 2.0

0xF0=DP

0xE1=HDMI 1.4

2P Input

Source 0x04 0x30 0x05 0xC7 0x04 0x05

0x00=VGA

0x01=DVI

0x07=HD

MI 2.0

0x08=DP

0x17=HD

MI 1.4

0xF7=VGA

0xF6=DVI

0xF0=HDMI 2.0

0xEF=DP

0xE0=HDMI 1.4

3P Input

Source 0x04 0x30 0x06 0xC6 0x04 0x06

0x00=VGA

0x01=DVI

0x07=HD

MI 2.0

0x08=DP

0x17=HD

MI 1.4

0xF6=VGA

0xF5=DVI

0xEF=HDMI 2.0

0xEE=DP

0xDF=HDMI 1.4

4P Input 0x04 0x30 0x07 0xC5 0x04 0x07 0x00=VGA 0xF5=VGA


User Manual 64

Source 0x01=DVI

0x07=HD

MI 2.0

0x08=DP

0x17=HD

MI 1.4

0xF4=DVI

0xEE=HDMI 2.0

0xED=DP

0xDE=HDMI 1.4

Display Mode 0x04 0x30 0x08 0xC4 0x04 0x08

0x00

Mode 1P

0x01

Mode 2P

(L/R)

0x02

Mode 2P

(T/B)

0x03

Mode 2P

(M/S)

0x04

Mode 4P

0xF4 Mode 1P

0xF3 Mode 2P

(L/R)

0xF2 Mode 2P

(T/B)

0xF1 Mode 2P

(M/S)

0xF0 Mode 4P

Region 0x04 0x30 0x09 0xC3 0x04 0x09

0x00 1P

0x01 2P

LR Left

0x02 2P

LR Right

0x03 2P

LR Full

0x04 2P

TB Top

0x05 2P

TB Button

0x06 2P

TB Full

0x07 2P

PIP Main

0x08 2P

PIP Sub

0x09 2P

PIP Full

0x00 1P

0x01 2P LR Left

0x02 2P LR

Right

0x03 2P LR Full

0x04 2P TB Top

0x05 2P TB

Button

0x06 2P TB Full

0x07 2P PIP

Main

0x08 2P PIP

Sub

0x09 2P PIP Full

0x0A 4P LT

Inside

0x0B 4P LT

Outside

0x0C 4P LB


User Manual 65

0x0A 4P LT

Inside

0x0B 4P LT

Outside

0x0C 4P

LB Inside

0x0D 4P

LB

Outside

0x0E 4P

RT Inside

0x0F 4P

RT

Outside

0x10 4P

RB Inside

0x11 4P

RB

Outside

0x12 4P

Full

Inside

0x0D 4P LB

Outside

0x0E 4P RT

Inside

0x0F 4P RT

Outside

0x10 4P RB

Inside

0x11 4P RB

Outside

0x12 4P Full

Brightness 0x04 0x30 0x10 0xBC 0x04 0x10 0x00-0x64 0xEC=0 ~

0x88=100

Contrast 0x04 0x30 0x11 0xBB 0x04 0x11 0x00-0x64 0xEB=0 ~

0x87=100

Hue 0x04 0x30 0x12 0xBA 0x04 0x12 0x00-0x64 0xEA=0 ~

0x86=100

Saturation 0x04 0x30 0x13 0xB9 0x04 0x13 0x00-0x64 0xE9=0 ~

0x85=100

ADC

Brightness 0x04 0x30 0x14 0xB8 0x04 0x14 0x00-0x64

0xE8=0 ~

0x84=100

Sharpness 0x04 0x30 0x15 0xB7 0x04 0x15 0x00-0x04 0xE7=0 ~

0xE3=4

Gamma 0x04 0x30 0x31 0x9B 0x04 0x31

0=Native

1=Gamma

1.8

2=Gamma

2.2

0xCB= Native

0xCA= Gamma

1.8 0xC9=

Gamma 2.2


User Manual 66

Color Temp 0x04 0x30 0x32 0x9A 0x04 0x32

0=user

1=9300K

2=6500K

3=sRBG

0xCA=user

0xC9=9300k

0xC8=6500k

0xC7=sRBG

Color-R 0x04 0x30 0x33 0x99 0x04 0x33 0x00-0x64 0xC9=0 ~

0x65=100

Color-G 0x04 0x30 0x34 0x98 0x04 0x34 0x00-0x64 0xC8=0 ~

0x64=100

Color-B 0x04 0x30 0x35 0x97 0x04 0x35 0x00-0x64 0xC7=0 ~

0x63=100

SCHEME 0x04 0x30 0x36 0x96 0x04 0x36

0=Standar

d

1=GAME

2=MOVIE

3=PHOTO

4=VIVID

5=USER

0xC6=Standard

0xC5=GAME

0xC4=MOVIE

0xC3=PHOTO

0xC2=VIVID

0xC1=USER

Volume 0x04 0x30 0x50 0x7C 0x04

0x50 0x00-0x64 0xAC=0 ~

0x48=100

Mute 0x04 0x30 0x54 0x78 0x04 0x54 0=OFF

1=ON

0xA8=OFF

0xA7 =ON

Audio Source 0x04 0x30 0x55 0x77 0x04 0x55

0=Analog

1=1P

2=2P

3=3P

4=4P

0xA7=Analog

0xA6=1P

0xA5=2P

0xA4=3P

0xA3=4P

LR RATIO 0x04 0x30 0x70 0x5C 0x04 0x70

0=RATIO 0

1=RATIO 0

2=RATIO 0

3=RATIO 0

4=RATIO 0

0x8C=RATIO 0

0x8B=RATIO 0

0x8A=RATIO 0

0x89=RATIO 0

0x88=RATIO 0

PIP SIZE 0x04 0x30 0x71 0x5B 0x04 0x71 0x00~0x0

A

0x8B=0~0x81=

10

FLIP 0x04 0x30 0x80 0x4C 0x04 0x80

0=ROTATE

0

1=ROTATE

90

2=ROTATE

0x7C=ROTATE 0

0x7B=ROTATE

90

0x7A=ROTATE

180


User Manual 67

180

3=ROTATE

270

4=H

MIRROR

5=V

MIRROR

0x79=ROTATE

270

0x78=H

MIRROR

0x77=V

MIRROR

SCALING 0x04 0x30 0x81 0x4B 0x04 0x81

0=FULL

1=16:9

2=4:3

3=5:4

4=1:1

0x7B=FULL

0x7A =16:9

0x79 =4:3

0x78 =5:4

0x77 =1:1

SCHEME Red

Hue 0x04 0x30 0x82 0x4A

0x04 0x82

0x00~0x6

4

0x7A=0~0x16=

100

SCHEME Red

Sat 0x04 0x30 0x83 0x49

0x04 0x83

0x00~0x6

4

0x79=0~0x15=1

00

SCHEME

Green Hue 0x04 0x30 0x84 0x48

0x04 0x84

0x00~0x6

4

0x78=0~0x14=1

00

SCHEME

Green Sat 0x04 0x30 0x85 0x47

0x04 0x85

0x00~0x6

4

0x77=0~0x13=1

00

SCHEME Blue

Hue 0x04 0x30 0x86 0x46

0x04 0x86

0x00~0x6

4

0x76=0~0x12=1

00

SCHEME Blue

Sat 0x04 0x30 0x87 0x45

0x04 0x87

0x00~0x6

4

0x75=0~0x11=1

00

SCHEME

Yellow Hue 0x04 0x30 0x88 0x44

0x04 0x88

0x00~0x6

4

0x74=0~0x10=1

00

SCHEME

Yellow Sat 0x04 0x30 0x89 0x43

0x04 0x89

0x00~0x6

4

0x73=0~0x0F=1

00

SCHEME

Magenta Hue 0x04 0x30 0x8A 0x42

0x04 0x8A

0x00~0x6

4

0x72=0~0x0E=1

00

SCHEME

Magenta Sat 0x04 0x30 0x8B 0x41

0x04 0x8B

0x00~0x6

4

0x71=0~0x0D=

100

SCHEME

Cyan Hue 0x04 0x30 0x8C 0x40

0x04 0x8C

0x00~0x6

4

0x70=0~0x0C=

100

SCHEME

Cyan Sat 0x04 0x30 0x8D 0x3F

0x04 0x8D

0x00~0x6

4

0x6F=0~0x0B=1

00


User Manual 68

Electrical Characteristics This section includes important information on

power input, input/analog input voltage and

power consumption in different modes.

Appendix


User Manual 69

Appendix E Electrical Characteristics

Power Input

Parameter Symbol Min. Typ. Max. Unit. Remark

Input Voltage Vin +10.8

+13.2

+12

+24V

+13.2+

+26.4

VDC Note 1

Analog Input Voltage VCVS - 1.0 1.1 Vp-p Note 2

VRGB - 0.7 1.1 Vp-p Note 2,3

Digital Input

Signal

H-level Vih 2.75 - 5.0 VDC Note 4

L-level Vil 0 - 1.0 VDC

Note 1: Power input.

Note 2: Composite and standard RGB video signal input impedance: 75Ω.

Note 3: RIN, GIN, BIN terminals (RGB video signals).

Note 4: HS, VS, DDCSDA, DDCSCL.

Power Consumption

Parameter Min. Typ. Max. Unit. Remark

Operating Mode - 3.6 4 Watt

Standby Mode - 2.5 - Watt

Off Mode - - 0.2 Watt

R2AP Panel Control Board - Winmate

Documents

Transcript of R2AP Panel Control Board - Winmate