Quolis 5000 Dental Unit -...

OPERATING INSTRUCTIONS

IMPORTANT

This manual provides operating instructions for the Maximus 5000 series. The instructions contained in this booklet should be thoroughly read and understood before operating the unit and chair. After the installation has been completed, keep this manual in a safe place and refer to it for future maintenance.

Quolis 5000 Dental Unit

Intended Use of the Product

This product is an active therapeutic device intended to administer or exchange energy of electric, air and water for the exclusive use for diagnoses, treatments and relative procedures of dentistry, and its characteristic is not in a potentially hazardous way between such energy and human body, taking account of the nature, the density and site of application of the energy.The product must be operated or handled by the qualified dentists or by dental staffs under the supervision of the dentist.Such dentists or dental staffs should instruct and/or assist the patients to approach to and leave from the product.Patients should not be allowed to operate or handle the product unless he/she is so instructed. The product is supplied together with the handpieces like electric micromotor, air turbine and/or motor, scaler and so on.

Environmental RequirmentsAmbient Temperature Operating 41° to 104° Storage 14° to 122F°Humidity 10 % - 80%Atmospheric Pressure 8.7psi – 15.4psi

Classification of Eqipmenta. Type of shock protection : Class I Equipment

b. Degree of shock protection : Type B Applied part

c. Degree of protection against water ingress : Ordinary Equipment (All Products)

d. Mode of operation : Continuous Operation

e. Flammable Gasses : Not suitable for use in the presence of a flammable anesthetic mixture with air,

oxygen, or nitrous oxide.

f. Earth : Protective earth (ground)

g. Hospital Grade Plug : Grounding reliability can be achieved only when the equipment is connected to an

equivalent receptacle marked hospital only or hospital grade.

OVERALL VIEW AND MAJOR COMPONENTS ------------------- 1

2. DIMENSIONS AND SPECIFICATIONS ------------------------------- 2 2-1. DIMENSIONS ------------------------------------------------------- 2 2-2. SPECIFICATIONS -------------------------------------------------- 2

3. OPERATING INSTRUCTIONS ----------------------------------------- 3 3-1. DOCTOR TABLE SECTIONS ------------------------------------ 2 3-2. VACUUM PACK SECTION --------------------------------------- 9 3-3. FOOT CONTROL SECTION -------------------------------------- 10

4. RIGHT / LEFT HANDED DENTISTRY CONVERSION ----------- 11

5. CARE AND MAINTENANCE ------------------------------------------- 12

6. UNIT FLOW DIAGRAM 6-1. DOCTOR TABLE SECTION -------------------------------------- 13 6-2. SWING ARM SECTION ------------------------------------------- 14 6-3.VACUUM PACK SECTION ---------------------------------------- 14 6-4. JUNCTION BOX SECTION --------------------------------------- 15 6-5. OVERALL UNIT FLOW DIAGRAM ---------------------------- 16

7. ELECTRICAL DIAGRAM 7-1. CHAIR SECTION --------------------------------------------------- 17 7-2. UNIT SECTION ----------------------------------------------------- 18

8. LOCATION OF PRODUCT LABELS --------------------------------- 19

TABLE OF CONTENTS

14

15

16

24

17 1918

21

2223

20

1

2

34

78

9

10

11

12

13

56

1. OVERALL VIEW AND MAJOR COMPONENTS

(17) SE Handpiece(18) Assistant Side Syringe(19) Assistant Touch Pad(20) Solid Collector (21) Assistant Swing Arm(22) Assistant Holder Arm(23) Vacuum Pack Control Panel(24) Dental Light

Fig.1-1 Overall View and Major Components

-1-

(1) Control Head (2) Main Control Panel (3) Dr. Table Indicator (4) Handle (5) Dr. Side Handpiece Holder (6) Dr. Side Syringe (7) Handpiece Hose (8) Foot Controller

(9) Balance Arm(10) Dr Swing Arm(11) Water Bottle(12) Junction Box(13) Dental Light Swing Arm(14) Light Pole(15) Assistant Holder(16) Vacuun Handpiece

2. DIMENSIONS AND SPECIFICATIONS 2-1. DIMENSIONS

- Inch /(mm) --Tolerance ±10%-

Power Consumption ------------------------------AC120V 1A

Frequency ------------------------------------------60 Hz

Fuse value ------------------------------------------AC125V 10A

Control Voltage ------------------------------------DC5V

Table Unit Net Weight ----------------------------25 kg

Swing Arm Net Weight ---------------------------25 kg (Without Dental Light)

Vacuum Pack Net Weight ------------------------20 kg

Junction Net Weight ------------------------------ 7 kg

Doctor Table Maximum Load ------------------- 2 kg(Gross weight of the doctor table are 8kg or less, the

spring of the balance arm can be adjusted.)

Operating Pressure -------------------------------- Water 0.2 MPa (30 psi) Max. 0.28 MPa (40 psi)

Air 0.5 MPa (75 psi)

Fig.2-1 Dimensions

-2-

2-2. SPECIFICATIONS

-3-

Fig.3-1-1 Master SwitchTurn off the master switch after daily operation and for long term interval.

3. OPERATING INSTRUCTIONS

3-1. DOCTOR TABLE SECTION

3-1-1. Master Switch (Fig.3-1-1 & Fig.3-1-2) Turn on the master switch located under the doctor table, the power indicator on the main control panel will then illuminate green.

3-1-2. Control Panel Main Control Panel

ONOFF

Fig.3-1-2 Main Control Panel

(1) Power Indicator(2) Function Switch(3) Spray Switch(4) Light Pack Switch(5) Function Indicator (6) Safety Lock Indicator(7) Dental Light Switch

(8) Electric Motor Direction Control Switch (9) Select Switch(10) Decreasing / Increasing Switch(11) Store Switch (12) Timer Switch(13) Chair Manual Control Switches(14) Chair Auto Mode Switch(15) Chair Auto Return Switch

1 2 3 4 5

6 7 8 9 10 11 12

13

15

14

Power Indicator

(1) Power Indicator Turn on the master switch, the power indicator will illuminate green.

(2) Function Switch Provides supplement function (flush out operation, control panel switching sound on/off, fiber optic handpiece illumination timing, changing the maximum speed of micromotor atvariable mode, selection of doctor number, etc.) selected by the function switch. (3) Spray Switch Turning on/off the coolant air/water for instruments. Micromotor can be selected four mode (air and water / air only / water only / none). Air turbine and air motor is available two mode (air and water / none) Electric scaler, only water is supplied.

Function Switch

Spray Switch

(4) Light Pack Switch Pick up the fiber optic handpiece from the holder, momentarily press the light pack switch, the indicator illuminates in green and the handpiece light turns on. To switch off the light pack, simply press the light pack switch again.

(5) Function Indicator Display the status of setting or handpiece. a) Operation after turning on the main switch After main switch is turned on , the following is displayed and jobs are done. 1) All the LED on the control panel lit. Program No.(Ver. No), Doctor No. are displayed. 2) Reading of several data from the memory. Reading of the status of the instrument holders. 3) Unless any promlem is found, the displays go off and only "Belmont" is displayed. 4) After the may SW is turned on, the above-mentioned process takes 5 seconds. Chairs cannot be operated during this period.

b) When instruments are properly put in the holders 1) The controller detect the holder where the instruments are not properly put, then make a beep and display the holder No(s). If you put the instrument properly during the beep, the beep stops and you can use the holder normally. 2) The holder which were detected not to be properly put with instroments cannot be used. In order to put an instrument there, turn off the main switch, put the instrument and then turn on the switch again after 5 seconds.

c) Automatic turning off of the display After several seconds, the displays go off automatically. 1) In 120 seconds after the final normal display (Belmont). 2) In 30 seconds after any operation. After that it display turns on when any switch on the panel is pressed.

(6) Safety Lock Indicator While the handpiece is running, the safety lock indicator illuminates amber and all chair control switches will not operate.

(7) Dental Light Switch Press the dental light switch to turn on/off the dental light.

Light Pack Switch

Light Pack Indicator

Safety Lock Indicator

Dental Light Switch

(8) Electric Motor Rotation Direction Control Switch (Optional) After picking up the electric motor from the holder, the electric motor rotation direction can be changed by momentarily pressing this switch the rotation direction will be indicated by the amber and green LEDs. Indicator in green : Forward Rotation Indicator in amber : Reverse Rotation (Note : Do not change the electric motor direction while the motor is running. When the electric motor with setting Reverse Rotation is returned the holder and picked up again, a buzzer sounds.

(9) Select Switch Selection of operation mode pf micromotor, scaler,. Selection of setting of function.

(10) Decreasing / Increasing Switch Press the decrease/increase switch to change mocromotor speed, scaler power, timer, alame etc.

(11) Store Switch Various setting can be put in memory pressing by store switch. The setting can be used when the main switch is turned on.

(12) Timer Switch Timer can be set maximum 90 mins. 59 secs. in 1 secs. segment. Momentary press the timer switch, and set the time by pressing decrease / increase switch.

(13) Chair Manual Control Switches 1) Seat Lifting -----------------Press the ( ) switch until the seat is lifted up to the desired position. 2) Seat Lowering --------------Press the ( ) switch until the seat is lowered to the desired position. 3) Backrest Reclining ---------Press the ( ) switch until the backrest is reclined to the desired position. 4) Backrest Raising -----------Press the ( ) switch until the backrest is raised up to the desired position.

(14) Chair Auto Mode Switches Preset Operation Momentarily press the preset-1 switch ( ), the chair moves to the preset 1 position and stops automatically. Preset 2 position operated by the preset switch ( ). Preset 3 position operated by the preset switch ( ).

(Note:For auto mode position adjustment refer to chair operation manual )

Electric Motor Direction Control Switch

Green LED(Forward Rotaition)

Amber LED(Reverse Rotation)

Decrease/Increase Switch

Timer Switch

Select Switch

Store Switch

Chair Manual Control Switches

Chair Auto Mode Switches

3-1-3. First priority function of the instruments The priority of the operation is given only to the instrument that has been withdrawed first. Only that instrument will be operable. 1) After all the handpiece are placed in the holders, the first instruments withdrawed will be operable. When more than one instruments are withdrawed and the first one is returned to the holder, “Return to the holder” will be displayed. After the second or third instrument are placed back to the holder, then withdraw agan the instrument that you want to use.

2) The operable instrument number will be displayed (see example)

3) The instrument will not be operable if it is withdrawed with the foot controller being pressed. Make sure to withdraw the handpiece before pressing the foot controller. The orange LED for rotation direction (counterclockwise rotation) will lit.

(15) Chair Auto Return Switch 1) Momentarily press the auto return switch ( ), the chair returns to the initial position (the seat is the lowest position and the backrest is the upright position) and stops automatically.

2) Emergency Stop (Safety Stop) During automatic movements (preset, auto return and last position memory), by momentarily pressing any chair control switch this will cancel the automatic movement immediately.

Auto Return Switch

3-1-4. Unit Supplement Functions A. Spray Switch

1) Turning on/off the coolant air/water for instruments. 1) Pick up the instrument from the holder.

2) Select spray mode

2) Setting and memory 1) Do the above mentioned setting 2) Momentarily press store switch to put it in memory. (Do not press the foot control)

3) The coolant air and water for instrument can be supplied in four modes or two modes. For micromotor, [Four Mode] can be selected. , Air and water / air only / water only / none. For air turbine and air motor, only [Two Mode] is available. Air and water / none. For electric scaler, only water is supplied. 4) Set to four mode or two mode

1)Momentarily press the function switch seven times.

2) Press the decrease switch for two mode 3) Press the increase switch for four mode (Note:Press any of the above keys in 10 seconds after

pressing function switch )

Spray Switch

C. Maximum Rotation Speed of Micromotor (available at variable rotation speed mode) The maximum rotation speed (rotation speed range) can be set. The speed depend on the model of the micromotr. The set speed remains until the man switch is turned off. Press [Store] switch to put it in memory. When two micromotor is used, the setting can be done for each one. 1) Press select switch( ) until “Va” is displayed on top of the display.

2) Press the decrease switch or increase switch ( ) to changing the maximum speed.

for DA-700(No torque adjustment)

for Bien Air MXVariable Mode Maximum Speed

Torque(%)Rotation Mode(Auto Reverse)

The currently adjusted speed

B. Fiber optic handpiece lighting mode (Optional) In case that fiber optic handpiece is installed, the fiber optic turns on when the handpiece is taken out of the holder, and turns off when the handpiece is returned to the holder. This could be changed to fiber optic turns on when the handpiece is taken out of the holder and drive air pedal of foot control is activated.

Setting 1) Press the function switch four times. 2) Press the increase switch ( ) for H (holder) mode. Press the decrease switch ( ) for F (foot control) mode. (Note: Press any of the above keys in 10 seconds after pressing function switch ) 3) Press store switch without rotating the instruments to put it in memory.

Function Switch Decrease/Increase Switch

The Maximum speed of micromotor at variable speed mode The Maximum speed of micromotor at variable speed mode can be selected between “three steps” or “five steps”. At three steps, the maximum speed will be 5000, 10000 and 40000 rpm. At five steps, the maximum speed will be 1000, 5000, 10000, 20000 and 40000rpm. The rotation speed range depends on the model of the micromotor.

1) Momentarily press the function switch six times and press the

decrease switch for three steps.

2) Momentarily press the function switch six times and press the

increase switch for five steps. (Note:Press any of the above keys in 10 seconds after pressing function switch.)


3 steps

2000 - 10000

2000 - 20000

2000 - 40000

5 steps

2000 - 5000

2000 - 10000

2000 - 20000

2000 - 30000

2000 - 40000

DA-700

3 steps

100 - 5000

1000 - 10000

1000 - 40000

5 steps

100 - 1000

100 - 5000

1000 - 10000

1000 - 20000

1000 - 40000

MX

-4-

E. Fixed Rotation Speed Mode This function can provide constant speed of electric motor up to three different speed(M1,M2,M3). The set speed remains until the man switch is turned off. Press [Store] switch to put it in memory. NOTE ; Once this function selected, foot controller behaves as on/off switch of electric motor and rotation speed can not be varied by foot controller. 1) Pick up the electric motor from the holder. 2) Momentarily press the select switch( )and repeat it until selected setting figure is displayed in function indicator.

To change the setting speed. 1) Pick up the electric motor from the holder. 2) Momentarily press the electric motor speed setting switch and repeat it until selected setting figure is displayed in function indicator. 3) Set up the required rotation speed by using increasing and/or decreasing switch. 4) Momentarily press store switch.

Rotation Speed Control Volume Knob

D. Rotation Speed Control Volume Knob (Optional) Turning the rotation speed control volume knob to change the rotation speed of micromotor.

(Note: When use the micromotor depressing the foot controller

to obtain enough coolant air. )

F. Torque adjustment of Bien Air MX Torque of rotation (%), Rotation mode (normal, auto forward, auto reverse), time of reverse rotation at auto forward setting and the intensity of the light can be adjusted. The setting can be done both for variable rotation mode and pre-set rotation mode. Torque adjustment and rotation mode change can be done only in low rotation speed (100 to 5000rpm). In high rotation speed, the torque remains 100%.

Setting 1) Withdraw MX motor 2) Press “F” until the display become like the example at right. 3) Press [ Select ] and select the item to adjust. 4) “>” will be displayed at the left side of the item to be adjusted. 5) Press [ - ] [ + ] to adjust. 6) To finish the setting, press [Store] switch. To cancel, press [F].

• Torque Setting The torque can be adjusted in the range of 10 to 100% In high speed rotation mode, the torque stays 100%. The actual torque value may change depending on the power input or the status of the motor.


Select SwitchFunction Switch

Store Switch

G. Timer Timer can be set maximum 90 mins. 59 secs. in 1 secs. segment. Preset time

1) Momentarily press the timer swith , and select the presetting time 0 > 1 > 2 > 3 by pressing the select switch . 2) Press the decrease switch or increase switch to change

the time. Press the select switch to switch the minutes or seconds.

3) Momentarily press the timer switch to start timer. The setting time is indicated on the function indicator. (Note:The presetting time remains until the man switch is turned off. Press Store switch to put it in memory)


Timer Switch Select Switch

Store Switch

• Rotation mode 1)NOR(Normal Mode) The motor remain rotation in onedirection regardless the load to the motor. 2) A. Rev (Auto reverse) The motor stop by a specific (programmable) load and turn to oposit direction. When you stop the motor and the restart, the motor turns in original direction. 3) A.FOW Auto Forward The motor stop by a specific (programmable) load and turn to oposit direction, then after a speficic (programmable) period, it the motor rotates in original direction again.

• Time of opposite rotation in Auto Forward mode The time of rotation in opposite direction in Auto Forward mode. (Note:The actual rotation time in the opposite direction will be longer than the displayed time approximately by 2 seconds.) • Intensity of the light of micromotor The intensity of the light of MX micromotor can be adjusted, within the range of 00 to 15.

Preset Time Adjustment Four preset time can be set. ( 0 > 1 > 2 > 3 )

1) Momentarily press the timer switch.

2) Press the select switch and select the preset number 0.

3) Press the decrease switch or increase switch to change

the time. Press the select switch to switch the minutes or seconds.

4) Press the store switch , then thme is memorized for preset 0. 5) Preset time 1 or 2.3 can be memorized by above 2 to 4.

-5-

H. Selection of Doctor Number Up to four dentists can program their own setting of the followings 1) Pre-set speed of micromotor and on/off of the light. 3 speeds each. (For MX, torque and rotation mode are also pre-programmable) 2) Timer of light of air turbine after releasing the foot pedal 3) Pre-set positions of the chair, 3 positions each. (Note : The chair needs to be able to transmit signals with this PCB and be programmed for four doctors. 4) Initial intensity (high / low) of the dental light. (Note : The dental light needs to be able to transmit signals with this PCB and be programmed for four doctors. 5) The setting of [F] switch.

Setting

1) Press function switch ( ) once.

The current docoto No. will be displayed. 2) Press any [Pre-set] switch 0, 1 2 or 3. of the chair ( ) ( ) ( ) ( ) (Note:Select doctor No. in 10 seconds after pressing function switch)

Function Switch Chair Auto Mode Switch

1) Short time flush out

Momentarily press the function switch two times and

momentarily press the decrease switch. Pick up the handpieces from the holder and set them in the buclet etc. By momentarily pressing the foot controller this starts short time flush out. Water comes out from the handpiece and stops automatically after 40 seconds. During flush out, by momentarily pressing any switch of doctor table or foot controller will cancel flush out immediately. 2) Long time flush out

Momentarily press the function switch two times and

momentarily press the increase switch. Pick up the handpieces from the holder and set them in the buclet etc. By momentarily pressing the foot controller this starts long time flush out for 5 minutes. During flush out, momentarily pressing the any switch of doctor table or foot controller will cancel flush out immediately.

I. Flush out system The QUOLIS is equipped with two types of flush out system. Short time flush out - Cleaning handpiece water lines for 40 secs. Long time flush out - Cleaning handpiece water lines for 5 mins. Function Switch Decrease/Increase

Switch

-6-

J. Control panel switching sound on/off You can turn on/off or change the frequency of the beep when you hear at pressing switch. Volume of tbe beep depends on the frequency.

1) Press function switch three times.

Turn off the beep ---------- press decrease switch Turn on the beep ---------- press increase switch Higher frequency ---------- press up switch Lower frequency ----------- press down switch Default frequency ---------- press 0 switch 2) After changing frequency, press increase switch (Note: Press any of the above keys in 10 seconds after pressing function switch.)


Up/Down Switch 0 Switch

K. Alarm sound Type of alarm sound can be selected among four. Changing alarm sound helps dentists to recognize the device making the sound.

Setting

1) Press function switc ( )five times.

2) Select alarm type 0, 1, 2 or 3 by pressing switch for pre-set positions of the chair ( ) ( ) ( ) ( ) (Note:Press any of the above keys in 10 seconds after pressing function switch )

Function Switch Chair Auto Mode Switch

L. Scaler for NSK Varios (Optional) The setting range of ultrasonic scaler can be selected in 3 ranges (Scaling, prosthesis removal, amalgam, plugging / Ultrasonic endodontic treatment / Ultrasonic periodontal treatment).

Select Switch Decrease/Increase Switch

1) Pick up the handpiece of scaler and set the range by

pressing select switch.

2)The power of the scaling can be adjustable by pressing the decrease switch or increase switch.

0 Switch

-8-

Doctor Table Section Control Knobs

3-1-5. Doctor Table Section Control Knobs A. Handpiece Spray Water Control Knobs The handpiece spray water control knobs are located under the doctor table. Each handpiece spray water control knob is 1-4 from the left side HP1,HP2,HP3,... The handpiece spray water volume can be controlled independently.

B. Doctor's Syringe Flow Control Knobs Doctor's syringe flow control knobs are located under the doctor table. The flow control knobs adjust the doctor's syringe air and water flow volume. The yellow capped knob is the air flow control knob, the blue capped knob is the water flow control knob.

Note : Turning the control knob counterclockwise will increase the flow volume and turning clockwise will decrease.

3-1-6. Handpiece pressure Gauge Handpiece drive air pressure gauge is located in the doctor table .While a handpiece is working, the handpiece drive air pressure is indicated on the handpiece pressure gauge.

Control Knob

Increase Decrease(Stop)

Handpiece Pressure Gauge

Balance Arm Air Brake

3-1-7. Balance Arm Air Brake Balance arm air brake button is located on the handle. Grasp the handle and press the air brake button to adjust the table height. Release the air brake button at the desires table position, the balaance arm is locked.

Note : Do not load over 2.0 kg on the table.

Doctor's Syringe Water Control Knobs

HP1

HP2

HP3

Doctor's Syringe Air Control Knobs

Air Brake ButtonAir Brake Button

Handpiece Pressure Gauge

-9-

(1) Assistant Side Control Panel (Fig.3-2-1) Chair auto mode switches and chair manual mode switch are located on the vacuum pack control panel. (2) Vacuum Pack Control Panel (Fig.3-2-1)

A. Service Water Outlet (Fig.3-2-1) The service water outlet provides a quick-connection for water.

B. Service Water Outlet Control Knob (Fig.3-2-1) The water volume from the service water outlet can be adjusted by the service water outlet control knob. Turning the knob counterclockwise will increase the flow volume and turning clockwise will decrease. C. Service Air Outlet (Fig,3-2-1) Service air outlet provides a quick-connection for air.

(3) Vacuum Pack height Adjustment (Fig.3-2-1) Press the lock cancel button to adjust the vacuum pack height. Release the lock cancel button at the desires position, the vacuum pack is locked. (Note: Lift up the vacuum pack a little when press the lock cancel button to adjust height)

3-2. VACUUM PACK SECTION

(4) Assistant’s Syringe Control Knobs(Fig.3-2-2) Assistant’s syringe flow control knobs are located in the cuspidor unit body. The yellow capped knob is to adjust the assistant's syringe air flow volume, and the blue capped knob is to adjust water flow volume.

Note : Turning a knob counterclockwise increase flow volume and turning clockwise will decrease.

Fig.3-2-2 Assistant’s Syringe Control Knob

Chair Auto Mode Switch

Chair Manual Control Switch

Chair Auto Return Switch

Service WaterControl Knob

Service Water Outlet

Service Air Outlet

Lock Cancel Button

Assistant Control Panel

Vacuum Pack Control Panel

Assistant's SyringeFlow Control Knobs

Increase Decrease

Fig.3-2-1 Vacuum Pack Section

-10-

Vacuum Handpiece and Saliva Ejector Handpiece

(5) Assistant Instrument Holder Saliva ejector handpiece and vacuum handpiece have stop valves to close and adjust suction power.

Saliva EjectorHandpiece

Open

Close

Vacuum Handpiece

Open

Close

3-3. FOOT CONTROL SECTION

Foot Control

Pick up a handpiece from the handpiece holder and depress the

foot control, the handpiece starts running and coolant air comes

out from the handpiece.

-11-

Light Pole

Doctor Table

Light Pole

Lock Pin

Doctor Table

4. RIGHT / LEFT HANDED DENTISTRY CONVERSION 1. Bring the doctor table to following position. (Fig.4-1) 2. Pull up the lock pin( ) on the light pole mount arm. Lift up the chair seat and rotate the light pole to the other side and set lock pin on light pole mount arm. (Fig.4-2) 3. Swing the doctor table to other side fully.(Fig.4-3) 4. Swing the vacuum pack to other side.(Fig.4-4)

Fig.4-1 Fig.4-2

Fig.4-3 Fig.4-4

Fig.5-2 Vacuum and Saliva Ejector Handpiece

Fig.5-1 Solid Collector Filter(3) Vacuum Handpiece and Saliva Ejector (Fig.5-2) A. Pull out the Vacuum hand piece from the vacuum hose and clean it. Loosen the vacuum hose nut, the vacuum hose can then be removed from the cuspidor unit.

5. CARE AND MAINTENANCE

Turn OFF the master switch after daily operation and for long term intervals.Turn the main water valve OFF after daily operation and for long term intervals.

CAUTION

CAUTION

All surfaces can be cleaned with DURR FD312 cleaner ( or equivalent).Do not drench the chair and unit.Wipe all surfaces dry after cleaning.

Cleaning Unit

(2) Solid Collector (Fig.5-1) Pull out the solid collector filter and clean it. After cleaning, refit the solid collector firmly.

Solid Collector Filter

B. After daily operation, run two cups of clean water through the handpieces to clean inside. Note : After cleaning the handpieces, apply a white vaseline lightly on the rubber O-Ring to prevent damage to this O-Ring.

-12-

Oil Mist Separator Body

Oil Mist Filter

(4) Oli Mist Separator Handpiece oil mist separator is located under the doctor table. The oil contained in the exhaust air of each handpeace is collected in this container. Once a week or oil comes to the red line, open the oil mist separator and clean the separator body and filter.

Saliva EjectorHandpiece Body

VacuumHandpiece Body

VacuumHose Saliva Ejector

Hose

Vacuum Saliva Ejector

Chip Joint

Lever

Lever

SE Screen

6. UNIT FLOW DIAGRAM6-1. DOCTOR TABLE SECTION

-13-

6-2. SWING ARM SECTION

6-3.VACUUM PACK SECTION

-14-

-15-

6-4. JUNCTION BOX SECTION

AIR

DRAIN

VACUUM

WATER

-16-

6-5. OVERALL UNIT FLOW DIAGRAM

AIR

DRAIN

VACUUM

WATER

-17-

7. ELECTRICAL DIAGRAM7-1.CHAIR SECTION

12

34

56

78

9

84736251

21

21

SV1

SV2

SV4

SV3

1 2 3 4 5 6

12

SV6

98

76

54

32

1

1 2W

hite

Yello

w

XA9P

AN

FU07

A0

11

Trun

k Li

ne B

for S

olen

oid

Valv

e

VL2P

Lock

Red

Brow

n

1051 6 2 7 3 8 4 9

CN9

5566

-10A

(MO

LEX)

43

12

VL2P

Fuse

F 10

ABlac

k

Gre

en/Y

ello

w

Black

Whi

te

Whi

teBl

ack

LN

CN18

IL-5

P-S3

EN2

(JA

E)

54

32

1

FLA

SH

CN17

IL-7

P-S3

EN2

(JA

E)

76

54

32

1

RY-2

005

(1.2

)

(3.4

)

(2.5

)

(3.4

)

3

11V

9V

Trun

k Li

ne fo

r Cap

acito

r

AN

FU12

A0

Brow

n

Yello

w

Ora

nge

Red

Gra

y

Purp

le

Blue

Gre

en

CN1-

2(1-

1)IL

-10P

-S3E

N2

(JA

E)

109

87

65

344

221

CN13

IL-3

P-S3

EN2

(JA

E)

CN14

IL-3

P-S3

EN2

(JA

E)

CN7

IL-3

P-S3

EN2

(JA

E)

CN6

IL-3

P-S3

EN2

(JA

E)

CN5

IL-3

P-S3

EN2

(JA

E)

CN12

IL-3

P-S3

EN2

(JA

E)321

CN15

IL-2

P-S3

EN2

(JA

E)211

CN2-

2(2-

1)IL

-6P-

S3EN

2(J

AE)

CN1-

1(1-

2)IL

-10P

-S3E

N2

(JA

E)

CN16

B03B

-XA

SK-1

CN9

B09B

-XA

SK-1

CN10

IL-1

0P-S

3EN

2(J

AE)

1 2 3 4 5 6

21

1 2 31 2 3

VL8P

56

109

87

65

344

221

1 2 3

Pote

ntio

met

er fo

r Bac

kres

tBr

own

Red

Ora

nge

109

87

65

43

21

Cont

rol P

.C.B

.(AG

FS13

*0)

XX-S

TD20

07/0

0TI

Rela

y P.C

.B.

120V

Yello

w

Blac

k do

t ind

icat

es m

ale

pin

side

[Rem

arks

]Co

nnec

tor S

ymbo

l

XA •

• • X

A C

onne

ctor

VL

• • •

VL

Conn

ecto

r

YL •

• • Y

L Co

nnec

tor

NM

F • •

• N

re M

ini F

it Co

nnec

tor

m •

• •

Min

i Uni

vers

al C

onne

ctor

(AM

P)Cap

Plug

21

Mot

or

123

Up

Dow

n

Rais

e

Recl

inin

g

Pote

ntio

met

er fo

r Sea

tBr

own

Red

Ora

nge

TSM

-CBC

-5LP

-M1-

E

Tran

sfor

mer

TK-1

20V-

2H

Red

Whi

te/R

ed

Brown

SW2

SW3

LIM

NO

L

Lim

itST

ORE

EWS

VDA

S20

E53

M

321

1 2 33211 2 3

Capa

cito

r45

uF

1 5 2 6 3 7 4 8

4

231 6 4 5

2 3 1 2

32

1

54

32

1

CN6

5566

-08A

(MO

LEX)

CN4

B02P

-NV

CN3

B3P-

VH

CN1

B2P-

VH

CN2

B10B

-XA

SK-1

N-A

CN8

B03B

-XA

SK-1

N-A

CN7

B04B

-XA

SK-1

N-A

CN10

5566

-06A

(MO

LEX)

CN5

B04P

-NV

109

87

65

344

221 Brown

544

221

Yello

w

Yello

wA

NFT

58A

0

Trun

k LI

ne fo

r Mot

or /

Capa

cito

rVL

6P

AN

FT57

A0

Tran

sfor

mer

Sec

tion(

120V

)

AN

ET56

A0

Mot

or S

ectio

n (1

15V

)

AN

FT56

A0

AN

DR5

0A0

AN

DR3

6A0

Trun

k Li

ne fo

r Rel

ay

Sole

noid

Val

ve S

ectio

n(1

20V

)

1 2 3 4

Chai

r Dow

n Pr

ohib

ition

Chai

r Ope

ratio

n Pr

ohib

ition

CN4-

1(4-

2)IL

-4P-

S3EN

2(J

AE)

CN8

B04B

-XA

SK-1

12

34

CN3

B05B

-XA

SK-1

SW4

MO

DE

SW1

31

(Pro

port

iona

l Sol

enoi

d Va

lve)

67

89

122

12

34

5

1

Whi

te

Red

10

NM

F2P

N.O

.CO

M

1 3 2

CN11

5556

-04A

Mai

n Sw

itch

L2

N4

24

Up

Dow

n

Rais

e

Recl

inin

g

CN2-

1(2-

2)IL

-6P-

S3EN

2(J

AE)

1 2 3 4 5 6

CN19

B05B

-XA

SK-1

3

1 2 3 4

DN

CS42

A0

CN4-

1(4-

2)IL

-4P-

S3EN

2(J

AE)

N.O

.CO

M

Unu

sed

12

CN9

IL-2

P-S3

EN2

(JA

E)

109

87

65

344

221

1112

13

Arm

rest

Mem

bran

e SW

- L(A

GFS

14A

0)

109

87

65

344

221

1112

13

109

87

65

344

221

1112

13

109

87

65

344

221

1112

1310

98

76

53

4422

111

1213

Dis

trib

utio

n P.C

.B.

(AG

FS12

A0)

(Dis

trib

utio

n P.C

.B. in

the

right

sid

e ar

mre

st)

XA9P

XA2P

Touc

hpad

Sw

itch

(AG

FS16

A0)

To S

eria

l Com

mun

icat

ion

Line

for

Doc

tor T

able

D L

ight

PCB

.

4

Rota

tion

Lock

EWS

VDA

S20

E53

DN

CS42

A0

AN

FT71

A0

Mai

n Po

wer

Sw

itch

Sect

ion

AN

FT64

A0

Trun

k Li

ne fo

r Den

tal L

ight

Pow

er S

ourc

e

AN

FT65

A0

Trun

k Li

ne ff

or C

hair

Pow

er S

ourc

e

AN

FT63

A0

Eart

h

AN

FT55

B0

XA13

P

XA13

PXA

13P

XA13

PXA

13P

AN

FT60

A0

AN

FT61

A0

Trun

k Li

ne B

for M

embr

ane

SWA

NFT

62A

0

Trun

k Li

ne C

for M

embr

ane

SW

AN

FT67

A0

Seria

l Com

mun

icat

ion

Line

AN

FT68

A0

D L

ight

Com

mun

icat

ion

Line

AN

FT69

A0

Touc

hpad

SW

Trun

k Li

ne A

for

Safe

ty S

witc

h fo

r Und

er P

ump

Cove

r

(AG

FS15

A0)

3

122

344

56

78

910

XA10

P

AN

FT76

A0

Ass

ista

nt S

ide

Green

22

44

AN

FT70

A0

Pow

er C

able

Sec

tionSa

fety

Sw

itch

for U

nder

Pum

p Co

ver

Brow

nRe

d

Brow

nRe

d

Chai

r Dow

n Pr

ohib

ition

Chai

r Ope

ratio

n Pr

ohib

ition

Motor

Up

Down

Reclining

Raise

Up/Down Slow Slide

Backrest Slow Slide

Lock Cancel

RedOrangeYellowGreenBluePurpleGray

Black

RedOrangeYellowGreenBluePurpleGray

Pink

WhiteBlack

White/Red

Light Blue

AR

Up

Down

Reclining

Raise

P1

P2

LP

COM

5V

Lock Cancel

Safety

Safety LED.

COM

BrownRed

Seria

l Tra

nsm

issi

on

Seria

l Rec

eptio

n

Seria

l Tra

nsm

issi

on

Seria

l Rec

eptio

n

RedBrown

RedBrown

OrangeYellowGreenBluePurpleGray

Black

Touc

hpad

SW

Trun

k Li

ne B

for

AR

Up

Down

Reclining

Raise

P1

P2

LP

COM

RedBrown

OrangeYellowGreenBluePurpleGrayBlack

RedBrown

OrangeYellowGreenBluePurpleGray

Black

AR

Up

Down

Reclining

Raise

P1

P2

LP

COM

Touc

hpad

SW

Trun

k Li

ne C

for

BrownRedOrangeYellowGreenBluePurpleGrayWhiteBlackPinkLight BlueWhite/Red



AR

Up

Down

Reclining

Raise

P1

P2

LP

5V

Lock Cancel

Safety

Safety LED.

COM

AR

Up

Down

Reclining

Raise

P1

P2

LP

5V

Lock Cancel

Safety

Safety LED.

COM

Arm

rest

Mem

bran

e SW

- R

Yello

wYe

llow

Yello

w

Yello

wW

hite

Red

Yello

wYe

llow

Gra

y

Gra

y

Trun

k Li

ne A

for M

embr

ane

SW

BlueBlue

Light Blue

Blue

White

White

Black

Black

White

Blac

kBl

ack

Whi

te

Whi

teYe

llow

Whi

teYe

llow

Whi

teYe

llow

Trun

k Li

ne A

for S

olen

oid

Valv

e

Motor

Up

Down

Reclining

Raise

COM Com

Up/Down Slow Slide

Backrest Slow Slide

COM

COM

Lock Cancel

SV8

SV7

3 2

VL4P4 1

Yello

wW

hite

Yello

wW

hite

Gre

enBl

ue

Yello

wO

rang

e

Up/

Dow

n Sl

ow S

lide

Back

rest

Slo

w S

lide

Back

rest

Slo

w

Up/

Dow

n Sl

ow

1 2

XA2P

Ther

mis

tor

NTC

The

rmis

tor

Red

Brow

nBl

ack

Blac

kTh

erm

isto

r for

Sol

enoi

d Va

lves

Chai

r upp

er fr

ame

Eart

h Li

ne Base

Whi

te

-18-

7-2. UNIT SECTION

12

1 2 3 4

1 2

HP

Hol

der S

W P

CB. F

ourt

h Li

ne

4 3 2 1

21G

ray

Purp

le

14142424

(2.3

)

(1)

CN36

B03B

-XA

SK-1

N-A

321

Tim

erSp

ray

F(Fu

nctio

n)ST

ORE

LED

MA

IN(G

reen

)LO

CK(O

rang

e)Li

ght P

ack(

Gre

en)

Spra

y A

ir(Bl

ue)

ãtì](

û?)

ê?ì](

óŒ)

Operation Switch

-+SE

LECT

Ligh

t Pac

kD

enta

l Lig

htê?

ãtêÿ

ë÷

Chair Operation Switch

LPP2P1AR

Rais

eD

own

UP

Trun

k Li

ne fo

r Dis

play

AN

FT93

A0

NO

COM

Min

i Air

Switc

h(F/

C)

AN

FT97

A0

AN

FT95

A0

AN

FT96

A0

AN

FT83

A0

AN

FT80

A0

AN

FT79

A0

AN

FT87

A0

AN

FT86

A0

AN

FT82

A0

AN

FT85

A0

Tran

sfor

mer

Sec

tion

AN

FT92

A0

Trun

k Li

ne fo

r Den

tal L

ight

Pow

er S

ourc

e (J

BOX)

AN

FT81

A0

21

32

13

21

3

Pow

er C

able

(UL)

JBO

X

AN

FT84

A0

Seria

l Com

mun

icat

ion

Line

AN

FT78

A0

Trun

k Li

ne fo

r HP

Hol

der

AN

FT77

A0

AGFS

17A

0

AGFS

20A

0

Air

SW

Fuse

F 10

A

120V

14V 24V

Tran

sfor

mer

FK-

023

Junc

tion

Box

Sect

ion

AC IN

1 2211 221

21

1 2 3

12

12

34

21

21

34

56

71

2

87654321 4321

8 7 6 5 4 3 2 1 87654321

1 2 3 4 5 6 7 8 1 2 3 4 1 21 221 1 221

1 2 3 4

43211 2

CN31

IL-2

P-S3

EN2

(JA

E)

21

CN3

IL-3

P-S3

EN2

(JA

E)

Seria

l Com

mun

icat

ion

Line

Se

rial T

rans

mis

sion

(1.2

)

Seria

l Rec

eptio

n(3

.4)

CN29

236-

747(

Gre

en)

(WAG

O)

CN26

IL-3

P-S3

EN2

(JA

E)PE

RIO

END

O

CN16

IL-4

P-S3

EN2

(JA

E)

Wat

er

Doc

tor M

embr

ane

SW(A

GFS

18A

0)

12

34

56

78

910

12

344

665

Uni

t P.C

.B.

(AG

FS22

**)

CN21

IL-4

P-S3

EN2

(JA

E)

POW

ER

CN2

IL-2

P-S3

EN2

(JA

E)CN4

IL-2

P-S3

EN2

(JA

E)

CN6

IL-2

P-S3

EN2

(JA

E)

CN7

IL-3

P-S3

EN2

(JA

E)

CN10

IL-2

P-S3

EN2

(JA

E)

CN12

IL-2

P-S3

EN2

(JA

E)

CN17

IL-2

P-S3

EN2

(JA

E)

Air

SW

CN24

IL-4

P-S3

EN2

(JA

E)

CN25

IL-4

P-S3

EN2

(JA

E)

LP1

LP2

LP3

LP4

CN27

236

-401

(Gra

y)W

AGO

12

34

56

78

910

12

344

665

CN14

IL-2

P-S3

EN2

(JA

E)

Air

Red

Blac

kRe

dBl

ack

CN30

IL-2

P-S3

EN2

(JA

E)

Dis

play

(AG

FS19

A0)

12

34

56

78

910

81

210

313

614

7

CN5

IL-1

0P-S

3EN

2(J

AE)

CN18

IL-2

P-S3

CN2

(JA

E)W

hite

Blac

k

HP1

SV

HP2

SV

HP3

SV

HP4

SV

CN8

IL-8

P-S3

EN2

(JA

E)

HP1HP2

HP4

12V

0V0VHP3

CN13

IL-8

P-S3

EN2

(JA

E)

CN1

IL-3

P-S3

EN2

(JA

E)

CN36

236

-401

(Gra

y)W

AGO

CN37

236

-401

(Gra

y)W

AGO

CN38

236

-401

(Gra

y)W

AGO

CN23

IL-4

P-S3

EN2

(JA

E)

CN11

IL-8

P-S3

EN2

(JA

E)

FLA

SH

CN28

IL-7

P-S3

EN2

(JA

E)

CN19

IL-2

P-S3

EN2

(JA

E)

CN9

IL-4

P-S3

EN2

(JA

E)

GN

DCN

22IL

-2P-

S3EN

2(J

AE)

HP4

HP3

HP2

HP1

CN32

IL-2

P-S3

EN2

(JA

E)CN

33IL

-2P-

S3EN

2(J

AE)

CN34

IL-2

P-S3

EN2

(JA

E)CN

35IL

-2P-

S3EN

2(J

AE)

CN20

IL-1

0P-S

3EN

2(J

AE)

CN15

IL-6

P-S3

EN2

(JA

E)

XA-1

3PXA

-6P

AN

FT98

A0

Trun

k Li

ne A

for D

r Mem

bran

e SW

AN

FT99

A0

HP3HP2HP1

HP4

---

+++

-+

8

Sole

noid

Val

ve fo

r Pilo

t Air

Sole

noid

Val

ve fo

r Pilo

tA

ND

T08A

0

-+

-+

25

Sole

noid

Val

ve fo

r Spr

ayA

ND

T07A

0

1 2

12

1 2 3 4

12

12

1 21 21 2H

P H

olde

r SW

PCB

.

L N

Blac

k

VL4P

VL2P

Pow

er S

ourc

e fo

r Den

tal L

ight

AGD

R39A

0

Brow

n

Red

XA2P

XA2P

Gre

enBl

ue

Ora

nge

Yello

w

Brow

nRe

d

Stan

dard

Spe

c.

Syrin

ge T

urbi

ne x

3

Brow

n

AN

FU04

A0

Mai

n A

ir SW

Sec

tion

AGFL

34A

0

AN

FU05

A0

Eart

h (D

r Tab

le)

CN1

PS-L

A-1

4P

45

911

12

CN1

12

1314

Brow

nRe

dO

rang

eG

reen

Yello

w

Blue

Gra

yPu

rple

Whi

te

Dynamic Output 1Dynamic Output 2Dynamic Output 3Dynamic LED 1Dynamic LED 2Dynamic LED 3

Red

BlackWhiteGray

BrownRed

OrangeYellowGreen

Blue

PurpleBlue

GreenYellow

Orange

Brown

Trun

k line

B fo

r 24V

.12V

Pow

er S

ourc

e

Purple

Blue

PurpleBlue

Purple

Blue

Black

Red

Mai

n G

auge

Cla

mp

Red

Blue

Red

Blac

k

Purp

leBl

ue

Trun

k line

A fo

r 24V

.12V

Pow

er S

ourc

e

Fuse

6A

Fuse

2A

Trun

k line

(Blue

) for

Fus

e Ho

lder

Trun

k line

(Red

) for

Fus

e Ho

lder

Gre

en/Y

ello

w

Trun

k line

(Blac

k) fo

r Fus

e Ho

lder

Chair

Pow

er S

upply

Sec

tion

Chair

Pow

er S

upply

Bl

ack

Blac

kBl

ack

Whi

teW

hite

Whi

teG

reen

Blac

kBl

ack

Gra

yW

hite

Whi

te

Whi

te

Gre

en/Y

ello

w

Earth

Purp

le

Purp

leO

rang

e

Ora

nge

Red Blac

kBl

uePu

rple

J-Bo

x G

auge

Cla

mp

Sect

ion

To C

hair

PCB.

(CH

)

Red

Blac

kRe

dBl

ack

Red

Blac

kRe

dBl

ack

HP

Hol

der S

W P

CB.

HP

Hol

der S

W P

CB.

Seria

l Tra

nsm

issi

on

Seria

l Rec

eptio

n

Brow

nBr

own

Brow

nBr

own

Brow

n

BrownRed

OrangeYellowGreen

Blue

WhiteGray

Purple

0V5VVFD-RS

Low

erSp

ray

Wat

er(B

lue)

Trun

k Li

ne B

for D

r Mem

bran

e SW

VFD-R/WVFD-E

VFD-1

VFD-3VFD-2

VFD-0

AN

FU69

A0

Trun

k line

(Blac

k) fo

r Fus

e Ho

lder

HP2

HP1

HP3

Input AInput BInput CInput DInput EInput FInput GInput HDisplay LED.Display LED.

Maximus

ET

L L

IST

ED

CU

SCO

NFOR

MS

TOUL

STD

73CE

RTIF

IED

TOCA

N/CS

A ST

D C2

2.2

NO. 6

8

Maximus

3058278

ETL CLASSIFIED

MEDICAL ANDDENTAL EQUIPMENT

CONFORMS TO UL STD 60601-1

8. LOCATION OF PRODUCT LABELS

(1) Product label & ETL label are located under the doctor table

(2) Product label (SRRIAL No.) is located side of the assistant swing arm.

-19-

(3) Product label (SRRIAL No.) is located side of the assistant swing arm.

NOTE

BELMONT EQUIPMENT, Division of Takara Belmont USA, Inc.101 Belmont Drive Somerset, New Jersey 08873 U.S.A. TEL.:(732) 469-5000 / (800) 223-1192 Fax.:(732)526-6322 / (800) 280-7504

TAKARA CO, CANADA LTD.2076 S. Sheridan Way, Mississauga, Ont., L5J2M4, Can. TEL.:(905) 822-2755 Fax.:(905)822-6203

Quolis 5000 Dental Unit -...

Documents

Transcript of Quolis 5000 Dental Unit -...