QUICK START GUIDE - Utcfss · PDF fileSTEP ONE: Acrobat OVERVIEW QUICK START GUIDE 1 Product...

QUICK START GUIDE4G Lite Product Series

Section One: Overview 1 to 4

Section Two: Wiring 5 to 11

Section Three: Communication 12 to 15

Section Four: ACP or SDAC 16 to 17

Section Five: Software 18 to 21

Section Six: Enrollment 22 to 24

Section Seven: Time & Attendance Operation (4G V-Station Lite)

25 to 29

Table of Contents

ST

EP

ON

E:

OV

ER

VIE

W

QUICK START GUIDE 1

Product Packaging Checklist

QTY DESCRIPTION

1 4G CR-Pass Device or 4G V-Flex Lite or 4G V-Station Lite1 Installation CD1 Installation Guide (on Installation CD)1 Operator’s Manual (on Installation CD)1 Quick Start Guide (Hard-copy and on Installation CD) 1 SST Wall Mount Plate1 4G MicroUSB Device Cable1 4G MicroUSB PC Cable 1 Clamp-on Ferrite Core 1 Machine Screw, Pin-in-Hex Security, Pan Head, SST, 6-32, 1/4” Length 1 Security Key, Pin-in-Hex, 2.5” Length 1 Security Screw Retainer, Stainless Steel 2 Self-Tapping Screw, Philip Pan Head, SST, #6, 1” Length 2 Dry Wall Anchor, Nylon, #4-8, 1” Length 2 Machine Screw, Philip Pan Head, SST, 6-32, 3/4” Length1 “Bioscrypt” Logo Sticker

4G CR-PASS, 4G V-FLEx LITE AND 4G V-STATION LITE

4G SECURECONTROL

QTY DESCRIPTION

1 4G SecureControl Device 1 Terminal Block, 1x12po, 3.5mm, RA1 Terminal Block, 1x14po, 3.5mm, RA1 Quick Start Guide (Hard-copy and on Installation CD) 4 Dry Wall Anchor, Nylon, #4-8, 1” Length 4 Self-Tapping Screw, Philip Pan Head, SST, #6, 1” Length 1 “Bioscrypt” Logo Sticker1 Clamp-on Ferrite Core (WLAN Only)1 Antenna, Omni Plug Connector (WLAN Only)

NOTE: Electronic documentation is provided in Adobe® Acrobat® format (PDF). Adobe® Acrobat® Reader is available on the Installation CD or at http://www.adobe.com

ST

EP

ON

E:

OV

ER

VIE

W

QUICK START GUIDE 2

Product Overview – 4G CR-Pass, 4G V-Flex Lite & 4G V-Station Lite

4G CR-PASS, 4G V-FLEX LITE and 4G V-STATION LITE= Tricolor Pass/Fail LED

Power Indicator LED

Internal Smart Card or Proximity Reader (optional on V-Flex Lite and V-Station Lite)

USB Port (bottom of device)

I/O Port 26 Pin Connector

4G V-FLEX LITE & 4G V-STATION LITE Ridge Lock & Finger Scan Sensor

4G V-STATION LITE ONLY 1.5” color LCD screen

PIN Keypad

Navigation Keys

2

3

6

1

7

8

9

4

5

NOTE: 4G CR-Pass, 4G V-Flex Lite and 4G V-Station Lite Relay 1 & 2 rated for 30VDC @ 1 Amp Contact Rating Inductive load. Product images are not to scale. All the products in the 4G Lite line share the same wire connections at the back.

2

1

4G CR-Pass

4G V-Flex Lite4G V-Flex Lite (back)

4G V-Station Lite

6

4

8

3

5

9

7

ST

EP

ON

E:

OV

ER

VIE

W

QUICK START GUIDE 3

Product Overview – 4G SecureControl

8

9

2

1

76

5

4G SecureControl Power and Status LED’s

Device Status LED’s

Door Status LED’s

Reset Push Button

SYNC Push Button

Ethernet Port

Antenna (for WLAN option only)

Terminal Blocks

Mounting Holes

Relays

2

3

6

7

1

8

9

10

10 4

5

43

NOTE: SecureControl Relay 1 & 2 rated for 30VDC @ 3 Amps Contact Rating Inductive load.

ST

EP

ON

E:

OV

ER

VIE

W

QUICK START GUIDE 4

Typical Install

RS-485

USB

Enrollment Reader

Ethernet/LAN

Door Control Communication

QUICK START GUIDE 5

ST

EP

TW

O:

WIR

ING

Wiring

RS-485 PC Communication

Use CAT-5 UTP (or better) cable (shielded recommended). Cable should be run in a daisy-chained connection from the unit to the PC’s DB9 COM port via an RS-485 to RS-232 converter. Ethernet

Ethernet connections to the device are made through Ethernet wires available on the back of the device (RJ-45 Connector not included). Refer to page 8 for RJ-45 connector config. options. PowerFor most installations, use 18-22 AWG cable. Remember to calculate line-loss when selecting cable.

Not applicable to 4G SecureControlWiegand Output to Access Control Panel (ACP)• For 18 AWG, the maximum cable distance is 500 ft.

(150m); for 20 AWG, the maximum is 300 ft. (90m); for 22 AWG, the maximum is 200 ft. (60m).

• Three-conductor wire (shielded recommended) is required for Data 0, Data 1, and WGND.*

USBStandard cable with Micro AB plug to A plug (USB on the Go) is used.Install Ferrite CoreIn order for the 4G Lite devices to comply with FCC Class B & CISPR 22 Class B regulations, the installer and/or end user is required to use the supplied Ferrite Material with 3 turns onthe Ethernet cables exiting the rear of all 4G V-Flex Lite and 4G CR-Pass models.In addition, compliance with the above regulations requires the installer and/or end user to use the supplied Ferrite Material with 3 turns on the I/O lines for the 14-pin terminal block cables of the SecureControl device with WLAN option only.

Ethernet Ferrite P/N: STEWARD 28A2432-0A2I/O Lines P/N: STEWARD 28A2432-0A2Install the ferrite cores as close to the device as possible.

IMPORTANT: Refer to local electrical codes and standards before selecting a cable type.* L-1 EAS always recommends the use of wiegand ground

QUICK START GUIDE 6

ST

EP

TW

O:

WIR

ING

Pin Out Diagram – 4G CR-Pass, 4G V-Flex Lite & 4G V-Station Lite

TOP OF UNIT

Pin No. Function Color 1 DC 12-24V Red 3 DC GND Black 5 RELAY_NO Yellow 7 RELAY_NC Orange 9 TTL_OUT_L White/Red 11 TTL_OUT_H White/Brown 13 TTL_INO Yellow/Blue 15 TTL_IN1 Blue/Brown 17 RS485A Blue 19 RS485B Blue/Black 21 ETH_TXP White/Green 23 ETH_RXP White/Orange *25 POE_VIN+ Red/Black

Pin No. Function Color 2 DC 12-24V Red 4 DC GND Black 6 E GND Black/Red/White 8 RELAY_COM Grey 10 WIEGAND_OUT0 Green 12 WIEGAND_OUT1 White 14 WIEGAND/TTL GND Black/White 16 WIEGAND_INO Green/White 18 WIEGAND_IN1 White/Black 20 RS485 GND Black/Red 22 ETH_TXN Red/Green/Black 24 ETH_RXN White/Red/Black *26 POE_VIN- Brown

NOTE: Both Red DC 12-24V wires (Pin 1 and Pin 2) and both Black DC GND wires (Pin 3 and Pin 4) must be connected to correctly share power current. *Pin 25 and Pin 26 apply to the 4G CR-Pass only.* Colour codes are different from previous product series

25

1

2

26

QUICK START GUIDE 7

ST

EP

TW

O:

WIR

ING

– 4G CR-Pass, 4G V-Flex Lite & 4G V-Station LiteRJ-45 ConnectorConfiguration

Cat5 Cable UnitBrown and Brown/White BrownBlue and Blue/White Red/BlackOrange/White White/OrangeOrange White/Red/BlackGreen Red/Green/BlackGreen/White White/Green

Cat5 Cable UnitBrown and Brown/White BrownBlue and Blue/White Red/BlackOrange/White White/GreenOrange Red/Green/BlackGreen White/Red/BlackGreen/White White/Orange

Type A

Type B

QUICK START GUIDE 8

ST

EP

TW

O:

WIR

ING

Pin Out Diagram – 4G SecureControl

RIGHT SIDE (14 PIN TERMINAL)

IN1 IN2 IN3 IN4 GND

ALARM SYNC GND

DOOR1 DOOR2 GND

REQ1 REQ2 GND

LEFT SIDE (12 PIN TERMINAL)

ETHERNET PORT (RJ45)

NO1 COM1

NC1

NO2 COM2

NC2

RS-485A RS-485B

SGND (485 GND)

EGND PWR+ COM

Relay 1

GPIDevice Status

Common Pins &Alarm

Requestto Exit(REx)

Door Status

Relay 2

RS-485

Power Input

QUICK START GUIDE 9

ST

EP

TW

O:

WIR

ING

4G SecureControl Wiring Mock-up

(Request to Exit)12V

COM NC

Ethernet RJ45

RS-485A

RS-485B

SGND EGND EGND

GND

REQ1

EGND

DOOR CONTACTDEADBOLT/DOOR STRIKE*M

ax Load 3 Amps @

30 VDC

EXIT

* Normally open configuration shown. Separate power supply required for door strike (not shown).Note: Outputs to ground if door contact is not used, to disable alarm.

QUICK START GUIDE 10

ST

EP

TW

O:

WIR

ING

Power Supply

Use an external power supply that provides a minimum of 0.5A at 12VDC PER DEVICE. The power supply should be regulated, filtered, and dedicated to L-1 EAS products only. If sharing power between devices, be sure that each unit receives 0.5A (e.g. two units would require a 12VDC, 1A supply).

A battery backup or uninterrupted power supply (UPS) with built-in surge protection is recommended.

Power Over Ethernet (PoE) - (for 4G CR-Pass only)

When the device is powered over Ethernet, an IEEE 802.3af compliant Active Midspan Injector must be used. This injector is not supplied with L-1 EAS products.

Power – 4G CR-Pass, 4G V-Flex Lite & 4G V-Station Lite

12V

EXTERNAL 12-24 VDCPOWER SOURCE

CONNECTIONS FORAN EXTERNAL POWER SOURCE E GND

+

-

Note: Always have earth ground (E GND Pin) connection as well to provide proper ESD protection including PoE.

WARNING: Under powering may cause memory and data corruption; over powering may cause hardware damage. Both of these situations will void the warranty.

PoE Injector Specs

• InputVoltage:90-264VAC,60Hz• InputCurrent:0.4A@100VAC• OutputVoltage:48VDC• OutputCurrent:0.32A• Power:15.36W

Note: The USB port on your computer does not provide enough power for the device to operate properly, a separate power supply must be always used.


ST

EP

TW

O:

WIR

ING

Power Supply

Use an external power supply that provides a minimum of 0.5A at 12VDC PER DEVICE. The power supply should be regulated, filtered, and dedicated to L-1 EAS products only. If sharing power between devices, be sure that each unit receives 0.5A (e.g. two units would require a 12VDC, 1A supply).

A battery backup or uninterrupted power supply (UPS) with built-in surge protection is recommended.

WARNING: Under powering may cause memory and data corruption; over powering may cause hardware damage. Both of these situations will void the warranty.

12V

EXTERNAL 12-24 VDCPOWER SOURCE

CONNECTIONS FORAN EXTERNAL POWER SOURCE

E GND

PWR-

PWR+

+

-

Power – 4G SecureControl


ST

EP

TH

RE

E: C

OM

MU

NIC

ATIO

N

When the device is connected to a PC workstation for the first time, a Found New Hardware message will be displayed.

TheHardwareInstallationWizardpromptsyoutoconnecttotheinternettosearchfor a driver.

Select Not at this time > Next. Then choose Install the driver automatically.

When the driver installation is complete, right-click on the My Computer icon and select Manage > Device Manager.

Under Ports (COM and LPT) you will find the port number associated with your Gadget Serial (e.g. COM3).*

USB – 4G CR-Pass, 4G V-Flex Lite & 4G V-Station Lite

*IMPORTANT: When registering your product in SecureAdmin Lite™ use this port number.

NOTE: The driver will not install properly unless SecureAdmin Lite™ has been installed first.


ST

EP

TH

RE

E: C

OM

MU

NIC

ATIO

N

RS-485

For RS-485 installations, the cable should be run in a daisy-chain configuration (i.e. converter > position 1 > position 2 > position 3, etc.).

Choose one twisted pair of conductors to use for RS-485A (Blue wire - Pin 17 of 26) and RS-485B (Blue/Black wire - Pin 19 of 26). Conductor should be used for RS-485_GND (Black/Red) Pin 20 of 26.

IMPORTANT: A maximum of 31 devices may be installed on the same line. The maximum total cable length is 4000 ft. (1200m). The cable must be dedicated to this installation and not used for any other purpose (use L-1 EAS products only).

NOTE: When installing a unit on a network with both legacy and new products, the new software will not detect the older product(s). In these mixed installations, both VeriAdmin™ and SecureAdmin Lite™ must be used.

RS-232from theCom Port

RS-485to 4000 ft.

@ 9600 Baud

RS-232to RS-485converter


ST

EP

TH

RE

E: C

OM

MU

NIC

ATIO

N

Wireless Option and Ethernet

4G Lite devices by default are DHCP enabled.

FOR WIRELESS LAN(S):

When a wireless network has been installed, it must be enabled through SecureAdmin LiteTM.

L-1 EAS wireless enabled devices support 802.11b and 802.11g standards. WEP Open, WPA and WPA2 are supported.

NOTE: SecureAdmin Lite™ software supports restricted IP address for improved security. This feature allows you to specify which IP addresses are allowed to communicate with the device.

SecureAdmin Lite™Server

wireless

LAN Ethernet

RS-485


ST

EP

TH

RE

E: C

OM

MU

NIC

ATIO

N

Wiegand Communication

Use 18-22 AWG cable (shielded cable is recommended) in a homerun configuration from each unit to the ACP.

Connect WIEGAND_OUT0 (Green wire – Pin 10 of 26) to ACP Data 0.

Connect WIEGAND_OUT1 (White wire – Pin 12 of 26) to ACP Data 1.

Connect WIEGAND GND (Black/White wire – Pin 14 of 26) to ACP reader common (0VDC).

Example Format Information Type: Standard 26-bit

Alt Site Code and Fail Site Code Range: 0-255

Template ID Number Range: 1-65535

Extended ID Number Range: N/A

ID Start Bit: 9

Length of ID: 16

Site Code Start bit: 1

Length of Site Code: 8

Start Bit: 0

NOTE: On installation, the system administrator will be prompted to select either a pre-existing Wiegand file format or create a custom format, and upload it to the unit before the first use. To configure a 4G Lite unit to send an alternate Site Code, a custom Wiegand format must be created.

IMPORTANT: By default, the Wiegand format is set to standard 26-bit with site code 0. For more information, refer to the Wiegand Tab section of the 4G Lite Operator’s Manual.


ST

EP

FO

UR

: AC

P O

R S

DA

C

Connection to the ACP

DOOR ACP

1 1 1

1. Wiegand Lines • PIN 10 Wiegand_OUT0 - Green Wire • PIN 12 Wiegand_OUT1 - White Wire • PIN 14 Wiegand/TTL_Ground - Black/White Wire

2. Communication between 4G devices and SecureAdmin Lite™ Ethernet

2

2

2

Ethernet

NOTE: ACP = Access Control Panel; PACS = Physical Access Control System; SDAC = Single Door Access Controller


ST

EP

FO

UR

: AC

P O

R S

DA

C

MOTION DETECTOR

DOOR

12V+-

COM5 – NO (Yellow Wire)

8 – COM (Grey Wire)

15

5

8

9

13

1

2

26

25

COMNC

DOOR CONTACT

DOORSTRIKE

*

Single Door Access Control

The 4G V-Flex Lite™, 4G CR-Pass™ and 4G V-Station Lite™ devices incorporate an internal relay that enables them to operate a deadbolt/door strike directly.

Example Install

WARNING: The internal relay is limited to a maximum current of 1 Amp. NOTE: If the door contact is not used, you have to connect pins 9 & 13. *Separate power supply required for door strike.


ST

EP

FIV

E:

SO

FTW

AR

E

PC Workstation

• Minimum1GHzIntel® Pentium® 4 or equivalent

• 1 GB RAM (2 GB recommended)

• CD-ROM drive

• One available COM port or USB port

• Ethernet card

• Display: 1024 x 768 high color (minimum)

•Regulated DC Power supply

•Door controller

•TCP/IP network environment

•RS-232 to RS-485 converter with power supply (for advanced administrative features)

SecureAdmin Lite™ Client

• 15 MB hard-disk space minimum

SecureAdmin Lite™ Server

•25 MB hard disk space minimum

Operating Systems Supported

•Windows Server® 2003 R2

•Windows Server® 2008 R1

•Windows XP Service Pack 2 or higher

•Windows 7 32-Bit and 64-Bit

System Requirements – SecureAdmin Lite

SQL Server™ 2008 Express Edition• 350 MB of available hard-disk space for

the recommended installation (425 MB of additional available hard disk space is recommended)

Additional Components

• Microsoft® .NET Framework 3.5 (requires 500 MB of hard-disk space)

•Windows Installer 4.5


ST

EP

FIV

E:

SO

FTW

AR

E

Software Installation – SecureAdmin Lite

To install the SecureAdmin Lite™ (Client and Server) software, the user must have Administrative rights. The software required to install SecureAdmin Lite™ is detected and installed automatically during the setup process.

SecureAdmin Lite™ software is installed by clicking the appropriate buttons on the Install Menu screen.

IMPORTANT: The client(s) will not run without the server. While you can have multiple SecureAdmin Lite™ Clients in your installation, only one SecureAdmin Lite™ Server is needed. Make sure that each client in your installation is directed to the target server. If this is a new installation, make sure you install SecureAdmin Lite™ Server first.

SecureAdmin Lite™Server

Client 3

Client 2

Client 1


ST

EP

FIV

E:

SO

FTW

AR

E

SecureAdmin Lite Password Prompt

The SecureAdmin Lite™ Username and Password are created at the time of server installation. They make up the user identification required to log in to the database.

SecureAdmin Lite Server™ identifies the machine on which the database is installed.

The machine’s IP address can be used as the SecureAdmin Lite™ Server name. If the server and client are installed on the same machine, localhost can be used as the SecureAdmin Lite™ Server name.

NOTE: The password should be from 6 to 20 characters long and must contain at least one letter, one number, or one special character.


ST

EP

FIV

E:

SO

FTW

AR

E

Device Registration 1. Click on the Network tab and then

click on the Register via Server button. The Register via Server dialog box will display.

2. For Ethernet, select the Search Automatically check box. For USB/COM port, select the appropriate port number.

3. Click the Scan button SecureAdmin Lite™ will scan the network for installed devices and display a list.

4. In the list, click the icon of the device you want to register. The Register Device dialog box will display.

5. Click Register. The Device Summary dialog box will display.

1

4

2 2

5

3


ST

EP

SIx

: EN

RO

LLM

EN

T

Enrollment Basics

New users are entered into the database through the process of “enrollment”. During this process, a user’s finger is scanned and a finger-scan template is generated. The Quick Enrollment button is used for a single fingerprint. This method is particularly useful when you need to quickly add a single user. The Advanced Enrollment button is used to select the best of three fingerprints.

To enroll a user, click on the Quick Enrollment button and follow the directions displayedintheEnrollmentWizard.

NOTE: For more information, refer to Enrolling Users section of the 4G Lite Operator’s Manual.


ST

EP

SIx

: EN

RO

LLM

EN

T

On Device Enrollment - 4G V-Station Lite

1. Login to Admin menu of LCD (refer to page 26)

2. Using the navigation keys (< >), select the Template icon and click OK.

3. Select the Add icon and click OK to create a new template.

4. You will be prompted to place your index finger on the device’s sensor in order to get a fingerprint reading and create a template.

5. Once the device has completed the process, you’ll get a Result screen on the quality of the reading obtained. Using the navigations keys (< >), you can choose to Accept it or Retry. If you Accept the Result, you will be prompted back to the main menu, otherwise you’ll be returned to the enrollment screen and you’ll have to repeat steps 2 through 4.

2

5

3

4


ST

EP

SIx

: EN

RO

LLM

EN

T

Enrollment Basics

Operating L-1 EAS devices is simple if a few basic guidelines are followed consistently. Use the following recommendations to ensure trouble-free finger-scan recognitions:

Arches

NOTE: While L-1 EAS encourages capturing the core, users must maintain a natural presentation that they can consistently repeat each time during verification.

Loops

Whorls


ST

EP

SE

VE

N: T

IME

& A

TTE

ND

AN

CE

O

PE

RATIO

N (

4G

V-S

TATIO

N L

ITE

)

Time & Attendance - Typical Setup for T&A Operation

Ethernet/LAN Applications

Time Management

Reporting

Evaluation


ST

EP

SE

VE

N: T

IME

& A

TTE

ND

AN

CE

O

PE

RATIO

N (

4G

V-S

TATIO

N L

ITE

)

1

4

2

5

6

3

Time & Attendance - 4G V-Station Lite Screen Access

Press Simultaneously

To navigate to the Login screen, press the Left Arrow (<) and OK keys simultaneously.

The default password for the 4G V-Station LiteTM is 0000.

It is recommended that you change the default password.

1. Navigation keys

2. Numeric keypad

3. System Menu

4. Info Menu

5. Security Menu

6. Template Menu


ST

EP

SE

VE

N: T

IME

& A

TTE

ND

AN

CE

O

PE

RATIO

N (

4G

V-S

TATIO

N L

ITE

)

Time & Attendance - Configuring T&A in SecureAdmin Lite

There are four Time and Attendance (T&A)modes for 4G V-Station Lite (detailed information can be found in the 4G Lite Operator’s Manual) :

1. Disabled - T&A is disabled.

2. F-Key as Input - T&A can be either mandatory or optional. In mandatory mode, the selection of a function key is required to complete authentication.

3. Fixed - T&A is enabled by selecting any one Active Function Key in SecureAdmin Lite . Following a successful authentication, only the Function Key selected will be displayed on the LCD and captured in the Transaction Log.

4. Manual - T&A is enabled by selecting any one Active Function Key in SecureAdmin This selection is displayed at the top of the LCD idle screen. Afterwards, the Function Key can be changed on the device via the navigation arrow keys. Following a successful authentication, the selected Function Key will be captured in the Transaction Log.

1 2

43


ST

EP

SE

VE

N: T

IME

& A

TTE

ND

AN

CE

O

PE

RATIO

N (

4G

V-S

TATIO

N L

ITE

)

Time & Attendance - Configuring T&A on device

1. Login to Admin menu of LCD (refer to page 26).

2. Using the navigation keys (<>) select the System icon and click OK

3. Once in the Main System Menu screen, select Settings and click OK.

4. From the Settings Menu, select Time Attendance and click OK.

5. Using the navigation keys (<>) select from the following options and click OK:

• Disable

• F Key as Input

• Fixed

• Manual

2

3

54


ST

EP

SE

VE

N: T

IME

& A

TTE

ND

AN

CE

O

PE

RATIO

N (

4G

V-S

TATIO

N L

ITE

)

Time & Attendance - Exporting Transaction Log Entries

1. Select the check boxes next to the transaction log entries you want to export (to the left of the Description column) or use Select All check box to select all entries.

2. Click the Export button. An Export dialog box is displayed.

3. Browse to the save folder and enter a file name.

4. Click Export button at the bottom of the dialog. The selected log entries are exported and saved to the specified file and location in .csv file format.

1 2

3

4

Technical SupportToll Free: 888 940 7477 905 940 [email protected]

Sales SupportToll Free: 800 444 0496 905 940 [email protected]

www.L1ID.com/EnterpriseAccessCopyright © 2012, L-1 Identity Solutions, Inc. All rights reserved. The trademarks identified herein are the trademarks or registered trademarks of L-1 Identity Solutions, Inc. or other third party. P/N: 430-4G-010-10-005

Please reference this number for product validation and warranty support.

4G SERIAL NUMBER

OFFICES – Canada • United States

QUICK START GUIDE - Utcfss · PDF fileSTEP ONE: Acrobat OVERVIEW QUICK START GUIDE 1 Product...

Documents

Transcript of QUICK START GUIDE - Utcfss · PDF fileSTEP ONE: Acrobat OVERVIEW QUICK START GUIDE 1 Product...