PV-1 Ventura II
Transcript of PV-1 Ventura II
PV-1 Ventura II
The PV-1 was used throughout WWII as a very effective long-range maritime patrol bomber. The PV-1 was offered to US allies through the “lend-lease” assistance program that provided needed war material to key allies including British Commonwealth member nations Canada and South Africa. This new 1/72 scale Minicraft PV-1 features RAF mandated changes to the cockpit glazing, distinctive turret, and optional markings representing aircraft from the RCAF (Canadian Air Force) Marking included in this kit are: RAF, No. 21 Sqn, 1943 RCAF, No. 1 Air Armament School, 1952
Minicraft Models, 1501 Commerce Drive, Elgin IL 60123 USA www.minicraftmodels.com
Printed in China
11661
PARTS LOCATING DIAGRAMSPRUE A
SPRUE B
SPRUE C
SPRUE D
CLEAR SPRUES F
CLEAR SPRUE EA14
A13 A4
A17
A18
A2A3
A5
A9A10
A8
A11
A1
B5
B6
B6
B4
B4
B7
B3 B2 B8 B9 B8 B9
B1
C6 C5
C4 C4
C2 C2C3R C3L
D6 D5
D15D2 D3 D11
D14D13
D12D4 D10 D9
D1
D8 D7
C1
A15E1
E9
E2
E5 E4E3
E10
F1
F2
F3
F4
E6
E7E8
A12
A6
A7
A16
CementCollerKlebenPegarIncollareColarKleven
DO NOT CementNe pas CollerNicht KlebenNo PegarNon IncollareNao ColarNiet Kleven
Cut awayCouperScheidenCortarTagliereCortarSnijden
Optional partsChoixAuswahlmoglichkeitEleccionSceltaOpacoKeuze
Repeat operationRŽpeeter l' opŽrationVorgang wiederholenRepitir la operacionRipetereRepitir a opera•aoHerhalen
Symmetrical assembly Drill hole
INTERIOR / TURRET1
All Parts
All interior parts CHROMATE GREEN
Turret interior CHROMATE GREENGuns GUNMETAL
Control yoke handles FLAT BLACK Control columns MEDIUM GRAY
A3 D1
D1C1
C1
A4
A2
A3
F3
Boulton-Paul Type C Turret
NOTEParts for two different turret styles are included.
RCAF Venturas carried the Martin turret.Assembly drawings show the Boulton-Paul turret in place.
Martin 250CE-13 Turret(RCAF Version ONLY)
Instrument paneldecal A17
A18
COCKPIT AND TURRET INSTALLATION2
All Partsexcept as noted
Interior CHROMATE GREEN
E2
F1
E4
E3
E5A6
E6 E7
A1
F2
B1
FUSELAGE ASSEMBLY4BELLY GUN3
All Partsexcept as noted
Machine guns GUNMETAL
D2
E8
E1
D15
A5
2
ENGINE ASSEMBLY7
Cylinders STEEL Crankcase MEDIUM GRAY
Firewall CHROMATE GREEN Propellers FLAT BLACK with YELLOW tips
Propeller hubs FLAT BLACK
B5 / A11
B4
C4B6
A12
All Partsexcept as noted
MAIN LANDING GEAR8
All Parts
Struts and hubs ALUMINUM Tires FLAT BLACK-GRAY
B7 B7
C3R C3LSTARBOARD (RIGHT) PORT (LEFT)
D4 D4
C2 C2
TAIL ASSEMBLY6
All PartsB3
A10
A8
A7
Note alignment
A9
B2
CANOPY INSTALLATION5
All Parts
E9
A15F4
E10
E8
STARBOARD (RIGHT) WING ASSEMBLY10
WING INSTALLATION11
PORT (LEFT) WING ASSEMBLY9
All Parts
All Parts
Wheel well interior CHROMATE GREEN
Wheel well interior CHROMATE GREEN
D6
C5
D9
D5
C6 D9
FINAL ASSEMBLY13
All Parts
Guns GUNMETAL
D12
D13
D10
D10
D11
B9
B82
LANDING GEAR INSTALLATION12
All Parts
Gear door interiors CHROMATE GREENTailwheel strut ALUMINUMTire FLAT BLACK-GRAY
RETRACTED MAIN GEAR OPTIONEXTENDED MAIN GEAR
D8
D7D3
Note alignment
D7 (Cut)
D7 (Cut)
D8 (Cut)D8 (Cut)
Cut parts D7/D8in half as shown
ANTENNA RIGGING DIAGRAM
1166
1
PAIN
TSA
RA
F D
ark
Eart
h (M
od
elM
aste
r 205
4, A
cryl
484
6)B
RA
F D
ark
Gre
en (M
od
elM
aste
r 206
0, A
cryl
484
9)C
RA
F Sk
y Ty
pe
S (M
od
elM
aste
r 204
9, A
cryl
484
0)D
Bl a
ck (M
od
elM
aste
r 174
9, A
cryl
476
8)E
Al u
min
um
(Mo
del
Mas
ter 1
781,
Acr
yl 4
677)
F C
a nad
ian
Red
9-2
(Mo
del
Mas
ter 2
718,
Acr
yl 4
632)
RA
F, N
o. 2
1 Sq
n, 1
943
1166
1
RC
AF,
No.
1 A
ir A
rmam
ent
Sch
oo
l, 19
52
Your Minicraft model includes high-quality waterslide decals. These decals adhere best to a glossy surface; and it is recommended that you apply a clear gloss coat over your painted model. Use a sharp scissors or knife to cut individual decals from the carrier sheet. Do not cut into the clear film surrounding the individual decals.
* It is recommended that you apply one decal at a time. * Place the decal section in warm water, when first inserted in the water your decal will curl, after approximately ten seconds the decal will uncurl. Remove from water and lay on a paper towel. After approximately 10 - 20 seconds the decal will slide freely from the backing paper. Use a small brush to help slide the decal from the backing paper and into position on the model. Carefully blot excess water from the decal, using care not to move the decal or tear it. * If you choose to use a setting solution, apply a thin coat over the decal following the manufacturer’s instruction. * Allow the decal to dry overnight. Wash any adhesive residue off the model with a small amount of clean water and dry thoroughly. * Apply clear gloss, matte or flat coat to seal decals following the instructions from the manufacturer.
Visit our Website- www.minicraftmodels.com
Minicraft Models 1501 Commerce Drive
Elgin, IL 60123
Phone: 847-429-9676