Push Through Glove System.pdf
-
Upload
creuza-barbosa -
Category
Documents
-
view
15 -
download
0
Transcript of Push Through Glove System.pdf
![Page 1: Push Through Glove System.pdf](https://reader036.fdocuments.us/reader036/viewer/2022071708/55cf9c06550346d033a84619/html5/thumbnails/1.jpg)
www.centres.com 800-934-1562
Push-Through Glove SystemCentral Research Laboratories (CRL)
P r e c i s e l y p o s i t i o n i n g o u r c u s t o m e r s f o r p r o d u c t i v i t y .
CompressedO-Ring
Glove BoxWall
EnclosureRing
O-RingGlove Bead
Support RingGlove
Rib
MachinedGroove
After Installation Before Installation
The CRL Push-Through Glove System allows for the interchangeability between gloves, viewing windows, bag-outs, and plugs without losing enclosure containment or risking the spread of contamination. The two main components of the system are the enclosure ring, which mounts to the Glovebox wall and the support ring or accessory that creates a compression seal inside the enclosure ring.
Design Features:•An independent O-Ring under high compression is used to maintain a tight seal between the enclosure ring and support ring or accessory item.
•Machined groove in the enclosure ring interfaces with a rib on the supportring to secure the support ring and glove in place without the need for a locking ring.
• Molded plastic support ring compatible with any 15 to 30 mil commercial glove. • Stainless Steel enclosure rings available in clamp-in or weld-in configurations.
![Page 2: Push Through Glove System.pdf](https://reader036.fdocuments.us/reader036/viewer/2022071708/55cf9c06550346d033a84619/html5/thumbnails/2.jpg)
www.centres.com
Push-Through Glove System
Dimensions and technical information are subject to change without notice
2
HANDLING INNOVATION
8
Basis of OperationThe CRL design utilizes an independent o-ring seal, under high compression to maintain the primary seal betweenthe enclosure ring (metallic ring), the glove support ring (plastic), and the glove as demonstrated below. The sealis established by forcing the glove sleeve through a serpentine path and securing it between the support ring andenclosure ring with an independent O-ring.
When installed, the seal is under high compression and securely held in position even without the use of a lockingring. Variations in glove thickness, resulting from the glove manufacturing process (dipping), are easily accommo-dated by o-ring compression and ensure a consistent high integrity seal is maintained with any 15 to 30 mil com-mercial glove.
![Page 3: Push Through Glove System.pdf](https://reader036.fdocuments.us/reader036/viewer/2022071708/55cf9c06550346d033a84619/html5/thumbnails/3.jpg)
www.centres.com
Push-Through Glove System
Dimensions and technical information are subject to change without notice
3
HANDLING INNOVATION
8
Enclosure Ring Mount ing Seals
Round Enclosure Systems
Enclosure Ring Assembly - Clamp In, No Seals:
Enclosure Ring Mounting Seals:
![Page 4: Push Through Glove System.pdf](https://reader036.fdocuments.us/reader036/viewer/2022071708/55cf9c06550346d033a84619/html5/thumbnails/4.jpg)
8
G love Support Ring
Required for installation of a glove or bag.
Ejectable Plug Assembly
www.centres.com
Push-Through Glove System
Dimensions and technical information are subject to change without notice
4
HANDLING INNOVATION
Oval Enclosure Systems
Oval Enclosure Ring Assembly:
Glove Support Ring:Required for installation of a glove or bag.
Ejectable Plug Assembly:
CRL_PTGS_0211