PUMP GUIDE - Dredging Contractorsswalfgroup.com/PDF/SYKES AUST BROCHURE -NEW CORRECT.pdf · Sykes...
-
Upload
vuongkhuong -
Category
Documents
-
view
215 -
download
1
Transcript of PUMP GUIDE - Dredging Contractorsswalfgroup.com/PDF/SYKES AUST BROCHURE -NEW CORRECT.pdf · Sykes...
Sykes was established in Australia in 1967 by UK pump group Henry Sykes Plc. The
company traded as Henry Sykes Pumps Pty Ltd importing pumps and equipment
from the UK until 1974 when local manufacture commenced in Gateshead,
Newcastle NSW.
Sykes Pumps manufactured pumps to suit the specific requirements of the
demanding Australian mining and construction industries.
In 1977 Sykes became part of another UK group Hanson Plc. The company traded
as Hanson Sykes Pumps Pty Ltd in Australia. In 1987 Jon Collins joined the board
in Australia after more than 18 years with Hanson Plc in the UK.
In 1988 Jon Collins was appointed managing director of Hanson Sykes Pumps
Pty Ltd and the head office was moved from Chatswood in Sydney to the
manufacturing plant in Gateshead, Newcastle. Jon Collins acquired the
organisation in 1992, thus ending its association with all other UK companies.
In 1992 the ownership of the business changed when Jon Collins was part of an
MBO thus ending the association with all UK companies, allowing the company
to focus on its Australian operations. Shortly after, the company changed its
name to Sykes Pumps Australia Pty Ltd when manufacturing operations moved
to Cardiff, Newcastle,
In early 1997 Sykes sold its hire division to Coates Hire Ltd and focused on
manufacturing and selling pumps worldwide. In 1998 Jon Collins became the
sole owner of Sykes Pumps Australia Pty Ltd.
In 2003 the company changed its name to Sykes Group Pty Ltd, the purpose of
this change was to reflect the company’s global market focus as well as to show
that ‘The Group’ were more than just a pump company.
Sykes Group was acquired by National Hire Group Ltd in 2010; parent company
of Allight and 46.1% shareholder of Coates Hire. Following the acquisition, the
combined group has a greater capacity to meet customer demand for sales and
support of pumps, lighting towers and other equipment solutions.
Andrew Aitken, Managing Director of National Hire said: “This is a company
transforming acquisition for National Hire’s equipment sales and support
business. Sykes Group provides scale, volume and distribution opportunities for
National Hire that will help underpin future growth.”
Sykes Chairman Jon Collins added; “Combining Sykes with National Hire is very
exciting because the businesses operate in common markets and have similar
core values. Like Sykes, the Allight brand is very well respected, and being in the
same family as Westrac and Coates Hire will enable Sykes to raise its profile and
access resources to create even more growth opportunities for all stakeholders.”
Find out more at www.allightsykes.com
Sykes Group
Our History
Introducing Henry the elephant “The Original Pump”
In addition to the traditional ‘triangle’ logo Sykes Group have a ‘living’ logo which is used to further strengthen the
company’s identity and to provide subliminal character to our products.
Sykes ‘living’ logo more clearly profiles Sykes while reinforcing the values in the brand. The elephant symbolises
reliability, robustness, strength, sturdiness, dependability, trustworthiness and consistency.
Sykes was established in Australia in 1967 to service the growing Australian
mining and construction industries. The Sykes Group is now one of the largest
auto prime pump manufacturers in the world.
Sykes take great pride in offering our customers a total equipment solution to
a variety of industries and a spectrum of applications.
Sykes provides an unmatched combination of application and product expertise
to meet your equipment needs. We specialise in the design, manufacture and
application of standard and custom built equipment for some of the most
challenging applications in the world and we have held the pioneering edge
in pump technology since 1967
We offer one of the broadest selections of equipment technologies and
product designs and are dedicated to helping our customers achieve the best
performance, whatever the industry.
Sykes provides local service through a highly trained network of branches
along with stocking distributors throughout the world. The Sykes Group has
been selling its range of products internationally for many years and continues
to expand world-wide.
Sykes is committed to delivering quality products and services to its customers by
working closely with them, ensuring all their requirements are met. A dedicated
problem solving team and the innovation of our research and development has
positioned Sykes as a forerunner in the industry and a market leader in self-
priming pumps providing engineering solutions for the harshest conditions.
Industry Leader
The Sykes Compressor Prime self-priming system utilises a jet of compressed air passed
through a venturi-type nozzle to evacuate the pump casing and suction line for fast, positive
and continuous priming, even under snore conditions. The priming system has no moving parts,
greatly reducing maintenance requirements.
Priming Systems
A proven alternative to the compressor prime system is the Sykes
Vacuum Prime self-priming system.
ImpellerStainless steel 316 for best corrosion resistance. Two per cent chromium and CD4MCu available as options. Impellers are open for best solids handling, and have back vanes and holes for pressure balancing.
Venturi primeSimple design, easy to clean. Modular for easy parts replacement. The venturi system requires very little maintenance, and is easily serviced in the field.
VoluteMade from spheroidal graphite cast iron. Spheroidal graphite iron provides superior strength compared to ductile and grey iron. Spheroidal graphite molecules prevent cracking in the metal thereby adding to the overall strength of the metal.
Wear platesReplacement front and rear wear plates made from 316 stainless steel. Chromium steel abrasive resistant and CD4MCU corrosive and abrasive resistant steel are available options. Replaceable wear plates lower operation and substitution costs by allowing adjustment of the wear plates to maintain efficiencies.
DischargeFlapper style check valve for deck discharge, or ball type for top discharge available.
CompressorWater cooled compressors are used for lower running costs. This means a longer life and less maintenance on the compressor and venturi priming system.
SealOil bath mechanical seals allow dry running for extended periods. The oil bath dissipates the heat and lubricates the seal. Materials of construction include silicone carbide and tungsten carbide for the most effective head and friction coefficient. New seals allow for higher pressures, this means improved performance in flooded suction and series pumping. Seal elastomers include Buna N and Viton.
ShaftMade from 431 stainless steel means no rust or pitting on the shaft for easier seal changes.
Vacuum priming chamberGreatly reduces carry-over due to the stainless steel baffle deflector plates and pancake float. Ideal for wellpoint dewatering and long suction conditions.
60cfm vacuum primeEnsures quick priming even in long suction conditions.
Float type head gearMade from anti-corrosive materials.
Over centre positive latchesFor easy access during servicing and maintenance.
VoluteMade from spheroidal graphite cast iron. Spheroidal graphite iron provides superior strength compared to ductile and grey iron.
ImpellerStainless steel 316 for best corrosion resistance, CD4MCu, and cast iron available as options. Impellers are open for best solids handling, and have back vanes and holes for pressure balancing.
Wear platesReplacement front and rear wear plates made from 316 stainless steel. Chromium steel abrasive resistant and CD4MCU corrosive and abrasive resistant steel are available options. Replaceable wear plates lower operation and substitution costs by allowing adjustment of the wear plates to maintain efficiencies.
DischargeFlapper style check valve for deck discharge, or ball type for top discharge, available.
Oil reservoir and oil/air separatorAre fitted integral to the vacumax chamber. The two stage oil separator reduces misting from the vacuum pump exhaust.
SealOil bath mechanical seals allow dry running for extended periods. The oil bath dissipates the heat and lubricates the seat.
ShaftMade from 431 stainless steel means no rust or pitting on the shaft for easier seal changes.
Product descriptions and specifications are approximations only and are subject to change without notice. No reliance can be made on these approximations.
Additional priming systems are available.
FLOW – CLEAR WATER PERFORMANCE
TOTA
L H
EAD
Sykes Contractors pumps are a fully automatic priming pump and can run dry for
extended periods due to the oil bath mechanical seal assembly which allows priming
with long suction hoses and suction lifts of up to 9 metres (28 feet). As fluid levels
fluctuate, the pump will “snore” until the time liquid is available for the pump to fully
reprime itself automatically.
Features • Low fuel usage
• Reduced engine sizes
• Lower maintenance costs
• Dry self prime and reprime
• Suction lifts to 9m
• Operates in 'snore' conditions
• Conversion kits for wellpoint dewatering and high heads
• Diesel, electric or hydraulic drive
• Solids handling up to 90mm
• Simple maintenance
• Replaceable wear parts
• Chassis – skid, road tow, wheeled, caged
• Zero emissions available
• Custom build available
Product descriptions and specifications are approximations only and are subject to change without notice. No reliance can be made on these approximations.
Contractors Range
Model Connections
(mm/in)
Maximum Head (m/ft)
Maximum Suction
(m/ft)
Maximum Flow (Ltrs per sec/
US Gallons per minute)
Solids Handling (mm/in)
Efficiency %
Approx Dimension (mm/in)
Approx Dry Weight (kg/lbs)
CP80i 75x75/3x3 28.5/93 9/30 40/634 38/1.5 56 1960L x 900W x 1300H 78L x 36W x 52H 840/1848
VMX80i 75x75/3x3 28.5/93 9/30 40/634 38/1.5 56 1960L x 900W x 1300H 78L x 36W x 52H 940/2068
CP100i 100x100/4x4 54/177 9/30 67/1061 45/1.8 72 1960L x 900W x 1300H 78L x 36W x 52H 850/1870
VMX100i 100x100/4x4 54/177 9/30 67/1061 45/1.8 72 1960L x 900W x 1300H 78L x 36W x 52H 950/2090
HD100i 100x100/4x4 35/115 N/A 55/871 45/1.8 72 2260L x 1000W x 1715H 89L x 40W x 68H 1350/2970
CP150i 150x150/6x6 60/197 9/30 174/2756 77/3 81 2340L x 1250W x 1900H 92L x 50W x 75H 1540/3388
VMX150i 150x150/6x6 60/197 9/30 174/2756 77/3 81 2340L x 1250W x 1900H 92L x 50W x 75H 1640/3608
HD150i 150x150/6x6 40/131 N/A 120/1900 77/3 81 2420L x 1000W x 1815H 96L x 40W x 72H 1500/3307
CP150iC 150x150/6x6 44/144 9/30 163/2582 77/3 74 1960L x 900W x 1300H 78L x 36W x 52H 1100/2420
VMX150iC 150x150/6x6 44/144 9/30 163/2582 77/3 74 1960L x 900W x 1300H 78L x 36W x 52H 1200/2640
HD150iC 150x150/6x6 23/75 N/A 120/1201 77/3 74 2260L x 1000W x 1815H 89L x 40W x 73H 1350/2970
CP220i 200x200/8x8 64/210 9/30 220/3485 80/3.2 78 2600L x 1520W x 2270H 103L x 60W x 90H 2370/5214
VMX220i 200x200/8x8 64/210 9/30 220/3485 80/3.2 78 2600L x 1520W x 2270H 103L x 60W x 90H 2470/5434
HD220i 200x200/8x8 38/125 N/A 180/2851 80/3.2 78 2600L x 1000W x 1815H 103L x 40W x 72H 1700/3748
CP300i 300x300/12x12 60/197 9/30 475/7524 90/3.6 80 5100L x 2200W x 2500H 201L x 87W x 99H 6300/13860
MH300 300x250/12x10 68/223 9/30 340/5386 75/3 56 4900L x 2000W x 3150H 193L x 79W x 124H 6100/13420
Sykes Contractors pump range has been designed to provide
greater cost efficient fluid handling solutions for all users.
The range offers efficiency levels of 83% which translate into
benefits for the end user and the environment.
Application• Construction
• Environmental
• Industrial
• Mining
• Clean Water
• Sludge
• Slimes
• Sewage
• Solids laden liquids
FLOW – CLEAR WATER PERFORMANCE
TOTA
L H
EA
D
Features• Full automatic prime
• Operates in 'snore' conditions
• Diesel, electric or hydraulic drive
• Simple maintenance
• Replaceable wear parts
• Solids handling up to 75mm
• Pressure tested fuel tanks
• High ground clearance on skids
• Bisalloy wear strips (optional)
• Interchangeable parts
• Engine protection as standard
• Suction booms (optional)
• Suction lifts to 9m
• Chassis
– skid, road tow, wheeled, caged
• Zero emissions available
• Custom builds available
Applications• Mining
• Quarries
• Industrial
• Pipelines
• Jetting
• Drilling
• Construction
The Himax range encompasses all the features of the Primax
range along with high head pumping ability.
Himax are built tuff to withstand the heavy duty requirements
of the mining and associated industries.
Product descriptions and specifications are approximations only and are subject to change without notice. No reliance can be made on these approximations.
Himax Range
Model Connections
(mm/in)
Maximum Head (m/ft)
Maximum Suction
(m/ft)
Maximum Flow (Ltrs per sec/
US Gallons per minute)
Solids Handling (mm/in)
Approx Dimension (mm/in)
Approx Dry Weight (kgs/lbs)
HH80 75x75/3x3 105/344 9/30 28/444 25/1 2340L x 1250W x 1900H 92L x 50W x 75H 1540/3388
HH100 150x100/6x4 130/426 9/30 56/887 29/1.14 (solids) 3000L x 1250W x 1870H 118L x 50W x 75H 2920/6424
HH125 150x150/6x6 130/426 9/30 56/887 29/1.14 (solids) 3500L x 1520W x 2250H 138L x 60W x 89H 2920/6424
HH150 200x150/8x6 99/325 9/30 150/2376 38/1.51 4500L x 1620W x 2400H 178L x 64W x 95H 3700/8140
HH160i 200x150/8x6 140/459 9/30 186/2946 38/1.5 4500L x 1800W x 2700H 177L x 71W x 106W 4000/8800
HH220i 200x200/8x8 138/453 9/30 282/4467 55/2.2 4900L x 2000W x 3150H 193L x 79W x 124H 7600/16720
FBP300 300x300/12x12 1140/460 9/30 340/5386 75/3 7000L x 2300W x 3200H 276L x 91W x 126H 12000/26400
FLOW – CLEAR WATER PERFORMANCE
TOTA
L H
EA
D
Sykes Xtra High Head Pump range caters to the demands of the
global mining industry with three models which have the ability
to operate unattended at high discharge heads.
All Xtra pumps have shaft stiffness ratios better than any pump
on the market. Sykes engineers have ensured that the enormous
pressures and loads associated with such performance do not
compromise seal integrity through shaft flexing.
Features• Pumps prime automatically
• 316 stainless steel pump internals
as standard
• Simple to service
• Runs dry without damage
• Solids handling
• Direct drive
• Operational chart fitted
• Adjustable and replaceable
wear plates
Product descriptions and specifications are approximations only and are subject to change without notice. No reliance can be made on these approximations.
Xtra Pump Range
Model Connections
(mm/in)
Maximum Head (m/ft)
Maximum Suction
(m/ft)
Maximum Flow (Ltrs per sec/
US Gallons per minute)
Solids Handling (mm/in)
Approx Dimension (mm/in)
Approx Dry Weight (kgs/lbs)
XH80 80x80/3.2x3.2 247/810 9/30 28/444 18/0.71 (solids) 4500L x 1620W x 2250H 180L x 64W x 90H 3900/8580
XH100 150x100/6x4 185/607 9/30 82/1299 22/0.88 4750L x 1820W x 2700H 187L x 72W x 106H 5560/12232
XH150 200x150/8x6 185/607 9/30 150/2376 43/1.7 5200L x 2150W x 3050H 205L x 85W x 120H 6850/15070
Applications• Mining
• Quarries
• Industrial
• Pipelines
• Jetting
• Drilling
• Construction
PrimingTwo systems are available utilising the same QS, canopy design:
• CP – compressor Prime
• VMX – ‘VACUMAX’ vacuum prime
Both systems are fully automatic and interchangeable. Sykes will advise on
application suitably.
Extremely quiet operationSykes QS Pumpsets have been designed to operate within all current noise
requirements on both worksites and in urban areas.
Hearing degradation is of great concern to all and Sykes have recognised the
need to design a range of sound proofed (QS) and super-sound proof (SQS)
pumpsets to minimise workers compensation claims and create a pleasant
working environment.
The QS series pumpsets are extremely quiet (62 dBA at 7 metres)
when operating at full load.
All QS models are compact in design and robust in construction.
Easy maintenanceRoutine maintenance can be performed through the large access doors
(lockable). External drain plugs are fitted for fuel, oil and water. The skid base fuel
tank can be easily drained and flushed out if required. The complete canopy can
be easily removed for major maintenance.
OptionsQS is available in the genuine Sykes vacumax or compressor prime configuration,
with a variety of diesel engines. Available in Primax or Himax range.
SkidThe QS pump and engine are set on a common skid base which incorporates
a 24 hour (minimum) fuel tank and bunded area.
PortableThe QS trailer mounted pumps are designed to be bolted onto a twin axle
galvanised trailer. These may also be fitted with hose racks to store 10 lengths of
suction hose, and 100 metres of layflat discharge hose along with the advantage
of a pump designed to run at a noise level of 62 dBA at 7 metres.
Quiet Solution (QS) Range
Model Connections
(mm/in)
Maximum Head (m/ft)
Maximum Suction
(m/ft)
Maximum Flow (Ltrs per sec/
US Gallons per minute)
Solids Handling (mm/in)
Approx Dimension (mm/in)
Approx Dry Weight (kgs/lbs)
QSCP80i 75x75/3x3 28.5/93 9/30 40/634 38/1.52500L x 1100W x 1900H
98L x 43W x 75H2100/4620
QSVMX80i 75x75/3x3 28.5/93 9/30 40/634 38/1.52500L x 1100W x 1900H
98L x 43W x 75H2400/5280
QSCP100i 100x100/4x4 54/177 9/30 67/1061 45/1.82500L x 1100W x 1900H
98L x 43W x 75H2100/4620
QSVMX100i 100x100/4x4 54/177 9/30 67/1061 45/1.82500L x 1100W x 1900H
98L x 43W x 75H2400/5280
QSCP150i 150x150/6x6 60/197 9/30 174/2756 77/32850L x 1100W x 1900H
110L x 43W x 75H2200/4840
QSVMX150i 150x150/6x6 60/197 9/30 174/2756 77/32850L x 1100W x 1900H
110L x 43W x 75H2500/5500
QSCP220i 200x200/8x8 64/210 9/30 220/3485 80/3.22850L x 1100W x 1900H
110L x 43W x 75H2400/5280
QSVMX220i 200x200/8x8 64/210 9/30 220/3485 80/3.22850L x 1100W x 1900H
110L x 43W x 75H2700/5940
QSCP300i 300x300/12x12 60/197 9/30 475/7524 90/3.65000L x 2000W x 2300H
197L x 79W x 91H8500/18700
The Yakka is robust and lightweight in design and offers
excellent maneuverability. It has been designed to suit the
requirements of almost any application suiting a three,
four or six inch pump, including; mining, construction,
sewer bypass and hire applications.
One of the main advantages of the Yakka pumpset is the extremely low noise
levels, due to the use of the accoustic casing. When run at 1500rpm the Yakka
emits a noise level of only 65.5dBA at seven metres, or 67.5dBA at 1800rpm.
FeaturesRobust• ‘QS’ silent canopy design
• Impact resistant polyethylene panels, easily removed for maintenance
• Tubular steel side/end protection
• Lockable gull wing doors for easy access
• Fuel tank ‘bunding’
• Quality accreditation AS9002
Compact• Lightweight in design
• 30 Hour fuel tank
• ‘Pod’ can be mounted on any trailer or sled
• Able to be mounted on a single axle trailer for improved maneuverability
• Single point lift
Efficient • High performance pump ends
• Increased flows
• Reduced fuel usage
• Solids handling
• Stainless steel impeller and wearplates as standard
Yakka Range
Model Connections
(mm/in)
Maximum Head (m/ft)
Maximum Suction
(m/ft)
Maximum Flow (Ltrs per sec/
US Gallons per minute)
Solids Handling (mm/in)
Approx Dimension (mm/in)
Approx Dry Weight (kgs/lbs)
YAKKA80HH 75x75/3x3 67/220 9/30 28/444 25/12250L x 1100W x 1375H
89L x 44W x 55H1325/2915
YAKKA100 100x100/4x4 37/122 9/30 67/1062 45/1.82250L x 1100W x 1375H
89L x 44W x 55H1325/2915
YAKKA150 150x150/6x6 29/96 9/30 132/2091 77/32250L x 1100W x 1375H
89L x 44W x 55H1325/2915
Moving dense slurries by pump is nothing new. Neither is
using a pump to pick up sediments. What’s new is using a
pump to pick up solids from rest, mixing them into a high
density slurry and pumping them all in one operation.
The Dragflow agitator slurry pumps are specifically
designed for this task.
The agitator is the key for picking up material from rest. The agitator is designed
to handle fast settling, high specific gravity solids and viscous thixotropic mud.
The agitator is used to physically and hydraulically force material away from the
pump’s suction. Doing this creates a “down pressure” stirring up material below
the pump’s suction. The created pressure differential (suction of pump versus
down pressure of agitator) will mix and homogenize the stirred up material.
The mixed and homogenized slurry is then drawn back into the suction
as a highly concentrated, uniform slurry.
Material too large to enter the pump’s suction (screen) is repelled and does not
plug the suction screen.
With installations all over the world from sumps, mine tailings reclamation,
dredging applications to mill scale pits, Dragflow Pumps offer a highly efficient
way of moving solids the world over.
Sykes Group is the Australian distributor for Dragflow Pumps.
Dragflow Pumps
Product descriptions and specifications are approximations only and are subject to change without notice. No reliance can be made on these approximations.
Grindex PumpsGrindex Drainage Pumps are designed for:
• Pumping water which may contain abrasive particles
– up to the size of the strainer holes.
• Pumping ground water.
• Pumping raw water.
Grindex Sludge Pumps are designed for:
• Water with high content of solids up to the size of the pump inlet
opening diameter.
• Water which contain abrasive particles.
• Different types of mud and sludge.
• Light slurry.
Grindex also have a range of Tuff Pumps which are ideal for all kinds of
professional drainage pumping where there are high demands on durability and
functionality. The light weight of these pumps makes them ideal for portable
purposes. They are equipped with stable and use-to-grip carrying handles.
These features, along with quality under tough operating conditions, put Grindex
pumps in a class all of their own. The fact that they are easy to service and have
a very long life makes them the indisputable best alternative, whatever Grindex
Pump you choose.
Sykes Group is the Australian distributor for Grindex Pumps.
Grindex pumps need no introduction in the construction,
mining and related industries. For over 40 years, the company
has pioneered developments in submersible pumps. The
various ranges available today, with their unique and patented
features that make Grindex so reliable, durable and excellent
performers, demonstrate the company’s ability to innovate.
There are Grindex pumps available in all sizes to meet all your
submersible pump requirements.
Product descriptions and specifications are approximations only and are subject to change without notice. No reliance can be made on these approximations.
The Pelican Dredge is designed and manufactured by
Sykes Group and is a breakthrough in shallow water dredging.
Features• One man operation
• Self contained and self propelled
• Operation in less than 1m deep
• Standard dredge will excavate to 4.5m deep
• Diesel Powered
• Optimum maneuverability
• Easily transportable
• Lightweight – less than 6 tonnes
• Handles solids to 60mm
Applications• Clearing out settlement and tailings ponds on mine sites
• Recovering river sands and gravels
• Clearing silt from industrial and municipal waste ponds
• Dredging irrigation channels and marinas
• Clearing weeds and similar growth from waterways and marinas
Pelican Dredge
When working on a construction site the last thing you need is wet and unstable
ground conditions.
Sykes offer specialist solutions to ground water control on a variety of
demanding construction sites. With extensive experience in all wellpoint
dewatering applications, Sykes are able to assist in designing a system
specifically to suit your application.
Complete dewatering systems are available to suit any application using vacuum
priming or submersible pumps or a combination system with pumps ranging
from two to 26 inches in diameter.
The wellpoint dewatering system offered by Sykes is lightweight and
corrosive resistant and incorporates control valves to trim and control the
dewatering process.
• Wellpoint ‘Spears’ – various sizes available, lightweight and easy to install
• Flexbows – Sykes three piece pushfit valve system is reusable and allows
for simple connection without special tools
• Hedder Pipe – Lightweight with simple clean holes
• Hedder Couplings
Hoses and fittingsThe diverse duties encountered by Sykes Group demands an equally versatile and
durable range of pumps, hoses and accessories.
Sykes products have been manufactured to conform to the rigorous standards
established by Sykes Engineering Department and are readily available from the
company’s network branches and from Sykes distributors throughout the world.
Trim-Well
The diversity of duties encountered by Sykes, demands an
equally versatile and durable range of pumps, hoses and
accessories. Sykes hoses and fittings have been manufactured
to conform to the rigorous standards established by Sykes
Group’s Engineering Department and are readily available
from the company’s network of branches and from Sykes
distributors throughout the world.
• Sykes Hose Coupling Range (bauer type) – Strong, simple, speedy and secure.
• Strainers – Split intake and general purpose strainers ensure no large solids
are drawn in to the pump avoiding damage to the pump. Lightweight and
easy to use, the strainer is fitted onto flanged or bauer hose tails.
• Reinforced PVC Heavy Duty Layflat Hose – A PVC layflat hose reinforced with
an embedded nylon web. Its layflat qualities enable the hose to be coiled for
easy storage and transportation.
• Wire Armoured Suction Hose – A tough, durable hose which will stand up to
the most arduous site conditions. Suitable for both suction and discharge lines.
• Galvanised Steel Pipe – Made from high quality, spiral welded, hot dipped
galvanized steel fitted with quick release couplings. The pipe is suitable for
discharge lines being reliable in operation, maintenance-free and robust.
Hoses, Couplings & Strainers
Spare PartsSykes supply spare parts for all Sykes products. Turnaround on parts is rapid,
with Sykes customer service ready to meet your needs 24 hours a day.
ServiceSykes Group’s commitment to supply all our customers with after sales service is
nothing short of excellent.
Whether it is a simple seal and bearing change or a complete pump overhaul,
Sykes can handle the job.
We provide local service through a highly trained team of staff. All service
technicians have a comprehensive knowledge of pumping equipment and the
experience to have all problems solved quickly.
Sykes also offer onsite application assistance to ensure your pump is running at its
optimum performance. Sykes trained staff will assess your application and help to
set up optimum operating settings which will help to reduce unnecessary wear
and tear on the pump whilst ensuring the pump is operating at its most efficient
duty.
Spare parts and after sales service
EngineeringSykes Engineering team is located at our NSW, Australia manufacturing facility.
This group provide the solutions and options to our customers many and varied
challenges through a multi-station CAD environment.
The quality assurance programs are strictly monitored and maintained
in conjunction with our accreditation to ISO 9001-2008. The Engineering
Department is responsible for the design of new products and existing product
enhancement.
The Engineering Team can assist with pump selection and provide the customer
a complete and certified test result ensuring the application will be met.
A fully integrated computer production and scheduling system enables fast and
accurate responses for all those day-to-day enquiries or that “red hot” delivery
requirement.
Research and DevelopmentSykes understands the need for a continuous exploration into research and
development, to provide our customers with the right solution for their job.
The research and development of product is always linked to industry and
customer needs.
Our engineering team welcomes the opportunity to liaise directly with our
clients and promote on site pre-delivery product inspections.
ManufacturingSykes has two manufacturing facilities, both accredited to the high standards
demanded for ISO 9001-2008.
At the purpose built manufacturing facilities each pump is thoroughly tested
and approved before being provided to the customer, to ensure the high
standards that they have come to expect.
Spare PartsSykes supply spare parts for all Sykes products. Turnaround on parts is rapid, with
Sykes customer service ready to meet your needs 24 hours a day.
ServiceSykes provide local service through a highly trained network of branches and
regional locations. All service technicians have a comprehensive knowledge of
pumping equipment and the experience to have all problems solved quickly.
QualityAt Sykes we strive to attain the
greatest customer satisfaction and
best quality products possible.
Sykes is a Quality Endorsed company with our quality management
system accredited to ISO 9001-2008. Sykes preferred suppliers are those
that are also quality accredited. Our well established quality control
program ensures that products are thoroughly inspected and tested
before final installation and commissioning.
Quality control testing is done on site at Sykes head office and
manufacturing facility in Newcastle, Australia where all pumps are tested
for performance on our certified test facility. Owners of Sykes equipment
benefit from the high level of control, and piece of mind that they have
bought a quality assured product. Sykes Dubai facility is also accredited
to ISO 9001-2008.
Disclaimer: Product descriptions and
specifications contained in this
publication are approximations
only and are subject to change
without notice. No reliance can be
made on these approximations.
DISTRIBUTED BY:
UNITED ARAB EMIRATES Manufacturing P.O. Box 17505, Lob 11-7 Jebel Ali Freezone DUBAI, UAE T +971 4 8811599F +971 4 8818883 UAE SALES OFFICEM +971 50 5596810T +971 4 324 1337F +971 4 324 1338E [email protected] UNITED KINGDOM SERVICE SUPPORT M +971 50 462 0358E [email protected] SOUTH EAST AND WESTERN USA South Carolina US Distribution Center 1107 E. Black Street Rock Hill, SC 29730 USA C +1 661 364 6481T +1 803 328 2035F +1 803 328 2036E [email protected] NORTH EAST USAC +1 803 322 2554E [email protected] LATIN AMERICA Roberto Guzman 8840, Las Condes Santiago, Chile C 56-9 6620 5996 E saleslatinamerica@sykesgroup.
NEWCASTLE, AUSTRALIA Head Office & Manufacturing 42 Munibung Road CARDIFF NSW 2285 T +61 (0)2 4954 3333F +61 (0)2 4954 3303E [email protected]
MELBOURNE, AUSTRALIA 5/115 Ricketts Road MT WAVERLEY VIC 3149 T +61 (0)3 9543 2000F +61 (0)3 9543 8000E [email protected]
PERTH, AUSTRALIA 14 Clyde Court MALAGA WA 6090 T +61 (0)8 9248 4944F +61 (0)8 9248 4988E [email protected]
DARWIN, AUSTRALIA M +61 (0)429 916 742E [email protected]
BRISBANE, AUSTRALIA Lot 9, 22 Eastern Service Road STAPYLTON QLD 4207 T +61 (0)7 3382 7600 F +61 (0)7 3382 7522E [email protected]
GLADSTONE, AUSTRALIA M +61 (0)427 543 323E [email protected]
TOWNSVILLE, AUSTRALIA M +61 (0)427 543 338E [email protected]
ADELAIDE, AUSTRALIA M +61 (0)401 107 075E [email protected]
AUCKLAND, NEW ZEALAND 13 McLaughlins Road MANUKAU CITY 2104 T +64 9 278 8300F +64 9 278 8700E [email protected]
CHRISTCHURCH, NEW ZEALAND 4 Chinook Place HORNBY T +64 3 344 2100F +64 3 344 2122E [email protected] SOUTHERN AFRICA M +27 (0)72 531 5108 M +27 (0)83 395 7377E [email protected] WEST AFRICA M +233 (0)27 318 9730E [email protected] AHMEDABAD, INDIA M +91 997 986 8599E [email protected] JAKARTA, INDONESIA M +62 813 8138 7705E [email protected]
com
April 2010 / V3 / 3K / 08774