PROFET™+ 12V BTS5008-1EKB · Automotive Power Data Sheet Rev. 2.1, 2015-02-17 BTS5008-1EKB Smart...

Automot ive Power

Data SheetRev. 2.1, 2015-02-17

BTS5008-1EKBSmart High-Side Power SwitchSingle Channel, 8mΩ

PROFET™+ 12V

Data Sheet 2 Rev. 2.1, 2015-02-17PROFET™+ 12V

BTS5008-1EKB

Table of Contents

1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73.1 Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73.2 Pin Definitions and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73.3 Voltage and Current Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 General Product Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94.2 Functional Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114.3 Thermal Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124.3.1 PCB set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124.3.2 Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5 Power Stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155.1 Output ON-state Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155.2 Turn ON/OFF Characteristics with Resistive Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155.3 Inductive Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165.3.1 Output Clamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165.3.2 Maximum Load Inductance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175.4 Inverse Current Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175.5 Electrical Characteristics Power Stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

6 Protection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216.1 Loss of Ground Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216.2 Undervoltage Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216.3 Overvoltage Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226.4 Reverse Polarity Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236.5 Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236.5.1 Current Limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236.5.2 Temperature Limitation in the Power DMOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246.6 Electrical Characteristics for the Protection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

7 Diagnostic Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277.1 IS Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277.2 SENSE Signal in Different Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287.3 SENSE Signal in the Nominal Current Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297.3.1 SENSE Signal Variation as a Function of Temperature and Load Current . . . . . . . . . . . . . . . . . . . 297.3.2 SENSE Signal Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307.3.3 SENSE Signal in Open Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317.3.3.1 Open Load in ON Diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317.3.3.2 Open Load in OFF Diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317.3.3.3 Open Load Diagnostic Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327.3.4 SENSE Signal with OUT in Short Circuit to VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337.3.5 SENSE Signal in Case of Overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337.3.6 SENSE Signal in Case of Inverse Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337.4 Electrical Characteristics Diagnostic Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

8 Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378.1 Input Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378.2 DEN Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Table of Contents

BTS5008-1EKB

Table of Contents


8.3 Input Pin Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378.4 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

9 Characterization Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399.1 General Product Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399.1.1 Minimum Functional Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399.1.2 Undervoltage Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399.1.3 Current Consumption Channel active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409.1.4 Standby Current for Whole Device with Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409.2 Power Stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409.2.1 Output Voltage Drop Limitation at Low Load Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409.2.2 Drain to Source Clamp Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419.2.3 Slew Rate at Turn ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429.2.4 Slew Rate at Turn OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429.2.5 Turn ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429.2.6 Turn OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439.2.7 Turn ON / OFF matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439.2.8 Switch ON Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449.2.9 Switch OFF Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449.3 Protection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459.3.1 Overload Condition in the Low Voltage Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459.3.2 Overload Condition in the High Voltage Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459.4 Diagnostic Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 469.4.1 Current Sense at no Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 469.4.2 Open Load Detection Threshold in ON State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 469.4.3 Sense Signal Saturation Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 479.4.4 Sense Signal maximum Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 479.5 Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489.5.1 Input Voltage Threshold ON to OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489.5.2 Input Voltage Threshold OFF to ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489.5.3 Input Voltage Hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499.5.4 Input Current High Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

10 Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5010.1 Further Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

11 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

12 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

PG-DSO-14-47 EP

Type Package MarkingBTS5008-1EKB PG-DSO-14-47 EP BTS5008-1EKB


Smart High-Side Power Switch

BTS5008-1EKB

1 Overview

Application• Suitable for resistive, inductive and capacitive loads• Replaces electromechanical relays, fuses and discrete circuits• Most suitable for loads with high inrush current, such as lamps

Basic Features• One channel device• Very low stand-by current• 3.3 V and 5 V compatible logic inputs• Electrostatic discharge protection (ESD)• Optimized electromagnetic compatibility• Logic ground independent from load ground• Very low power DMOS leakage current in OFF state• Green product (RoHS compliant)• AEC qualified

DescriptionThe BTS5008-1EKB is a 8 mΩ single channel Smart High-Side Power Switch, embedded in a PG-DSO-14-47 EP,Exposed Pad package, providing protective functions and diagnosis. The power transistor is built by an N-channelvertical power MOSFET with charge pump. The device is integrated in Smart6 technology. It is specially designedto drive lamps up to HIDL / H9, as well as LEDs in the harsh automotive environment.

Table 1 Product SummaryParameter Symbol ValueOperating voltage range VS(OP) 5 V ... 28 VMaximum supply voltage VS(LD) 41 VMaximum ON state resistance at TJ = 150 °C RDS(ON) 16 mΩNominal load current IL(NOM) 11 ATypical current sense ratio kILIS 4400

BTS5008-1EKB

Overview


Diagnostic Functions• Proportional load current sense• Open load in ON and OFF• Short circuit to battery and ground• Overtemperature• Stable diagnostic signal during short circuit• Enhanced kILIS dependency with temperature and load current

Protection Functions• Stable behavior during undervoltage• Reverse polarity protection with external components• Secure load turn-off during logic ground disconnect with external components• Overtemperature protection with restart• Overvoltage protection with external components• Voltage dependent current limitation• Enhanced short circuit operation

Minimum current limitation IL5(SC) 65 AMaximum standby current with load at TJ = 25 °C IS(OFF) 1.4 µA

Table 1 Product Summary (cont’d)Parameter Symbol Value

BTS5008-1EKB

Block Diagram


2 Block Diagram

Figure 1 Block Diagram for the BTS5008-1EKB

Block diagram.emf

VS

OUT

IN

T

driver logic

gate control &

charge pump

load current sense andopen load detection

overtemperature clamp for

inductive load

over currentswitch limit

forward voltage drop detection

voltage sensor

GND

ESDprotection

IS

DEN

internal power supply

BTS5008-1EKB

Pin Configuration


3 Pin Configuration

3.1 Pin Assignment

Figure 2 Pin Configuration

3.2 Pin Definitions and Functions

Pin Symbol FunctionCooling Tab VS Voltage Supply; Battery voltage 1, 2, 7, 8, 9, 13, 14 NC Not Connected; No internal connection to the chip 3 GND GrouND; Ground connection 4 IN INput channel; Input signal for channel activation 5 DEN Diagnostic ENable; Digital signal to enable/disable the diagnosis of the device 6 IS Sense; Sense current of the selected channel 10, 11, 12 OUT OUTput; Protected high side power output channel1) 1) All output pins must be connected together on the PCB. All pins of the output are internally connected together. PCB traces

have to be designed to withstand the maximum current which can flow.

Pinout single SO14.vsd

NC

NC

OUT

OUT

OUT

NC

NC

NC

NC

GND

IN

DEN

IS

NC

14

13

12

11

10

9

8

1

2

3

4

5

6

7

BTS5008-1EKB

Pin Configuration


3.3 Voltage and Current DefinitionFigure 3 shows all terms used in this data sheet, with associated convention for positive values.

Figure 3 Voltage and Current Definition

VS

IN

DEN

ISGND

OUT

IIN

IDEN

IIS

VS

VIN

VDEN

VIS

I S

IGND

VDS

VOUT

IOUT

voltage and current convention single.vsd

BTS5008-1EKB

General Product Characteristics


4 General Product Characteristics

4.1 Absolute Maximum Ratings

Table 2 Absolute Maximum Ratings 1)

TJ = -40 °C to +150 °C; (unless otherwise specified)

Parameter Symbol Values Unit Note / Test Condition

NumberMin. Typ. Max.

Supply VoltagesSupply voltage VS -0.3 – 28 V – P_4.1.1Reverse polarity voltage -VS(REV) 0 – 16 V t < 2 min

TA = 25 °C RL ≥ 2 Ω RGND = 150 Ω

P_4.1.2

Supply voltage for short circuit protection

VBAT(SC) 0 – 24 V 2) RECU = 20 mΩ RCable= 16 mΩ/m LCable= 1 µH/m, l = 0 or 5 m See Chapter 6 and Figure 52

P_4.1.3

Supply voltage for Load dump protection

VS(LD) – – 41 V 3) RI = 2 Ω RL = 2 Ω

P_4.1.12

Short Circuit CapabilityPermanent short circuit IN pin toggles

nRSC1 – – 100 k cycles

2) tON = 300ms

P_4.1.4

Input PinsVoltage at INPUT pin VIN -0.3

–– 6

7V –

t < 2 minP_4.1.13

Current through INPUT pin IIN -2 – 2 mA – P_4.1.14Voltage at DEN pin VDEN -0.3

–– 6

7V –

t < 2 minP_4.1.15

Current through DEN pin IDEN -2 – 2 mA – P_4.1.16Sense PinVoltage at IS pin VIS -0.3 – VS V – P_4.1.19Current through IS pin IIS -25 – 50 mA – P_4.1.20Power StageLoad current | IL | – – IL(LIM) A – P_4.1.21Power dissipation (DC) PTOT – – 2 W TA = 85 °C

TJ < 150 °CP_4.1.22

Maximum energy dissipation Single pulse

EAS – – 160 mJ IL(0) = 11 A TJ(0) = 150 °C VS = 13.5 V

P_4.1.23

BTS5008-1EKB



Notes1. Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute

maximum rating conditions for extended periods may affect device reliability.2. Integrated protection functions are designed to prevent IC destruction under fault conditions described in the

data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not designed for continuous repetitive operation.

Voltage at power transistor VDS – – 41 V – P_4.1.26CurrentsCurrent through ground pin I GND -20

-150– 20

20mA –

t < 2 minP_4.1.27

TemperaturesJunction temperature TJ -40 – 150 °C – P_4.1.28Storage temperature TSTG -55 – 150 °C – P_4.1.30ESD SusceptibilityESD susceptibility (all pins) VESD -2 – 2 kV 4) HBM P_4.1.31ESD susceptibility OUT Pin vs. GND and VS connected

VESD -4 – 4 kV 4) HBM P_4.1.32

ESD susceptibility VESD -500 – 500 V 5) CDM P_4.1.33ESD susceptibility pin(corner pins)

VESD -750 – 750 V 5) CDM P_4.1.34

1) Not subject to production test. Specified by design.2) EOL tests according to AECQ100-012. Threshold limit for short circuit failures: 100ppm. Please refer to the legal disclaimer

for short circuit capability on the page 53 of this document. 3) VS(LD) is setup without the DUT connected to the generator per ISO 7637-1.4) ESD susceptibility HBM according to ANSI/ESDA/JEDEC JS-001-20105) “CDM” ESDA STM5.3.1

Table 2 Absolute Maximum Ratings (cont’d)1)

TJ = -40 °C to +150 °C; (unless otherwise specified)



BTS5008-1EKB



4.2 Functional Range

Table 3 Functional Range TJ = -40 °C to +150 °C; (unless otherwise specified)



Nominal operating voltage VNOM 8 13.5 18 V – P_4.2.1Extended operating voltage VS(OP) 5 – 28 V 2) VIN = 4.5 V

RL = 2 Ω VDS < 0.5 V See Figure 15

P_4.2.2

Minimum functional supply voltage

VS(OP)_MIN 3.8 4.2 5 V 1) VIN = 4.5 V RL = 2 Ω From IOUT = 0 A to VDS < 0.5 V; See Figure 15

P_4.2.3

Undervoltage shutdown VS(UV) 3 3.4 4.1 V 1) VIN = 4.5 V VDEN = 0 V RL = 2 Ω From VDS < 1 V; to IOUT = 0 A See Figure 15See Figure 30

P_4.2.4

Undervoltage shutdown hysteresis

VS(UV)_HYS – 850 – mV 2) – P_4.2.13

Operating current channel active

IGND_1 – 5 9 mA VIN = 5.5 V VDEN = 5.5 V Device in RDS(ON) VS = 18 V See Figure 31

P_4.2.5

Standby current for whole device with load (ambiente)

IS(OFF) – 0.01 1.4 µA 1) VS = 18 V VOUT = 0 V VIN floating VDEN floating TJ ≤ 85 °C See Figure 32

P_4.2.7

Maximum standby current for whole device with load

IS(OFF)_150 – 6 54 µA VS = 18 V VOUT = 0 V VIN floating VDEN floating TJ = 150 °C See Figure 32

P_4.2.10

Standby current for whole device with load, diagnostic active

IS(OFF_DEN) – 0.6 – mA 2) VS = 18 V VOUT = 0 V VIN floating VDEN = 5.5 V

P_4.2.8

BTS5008-1EKB



Note: Within the functional range the IC operates as described in the circuit description. The electrical characteristics are specified within the conditions given in the related electrical characteristics table.

4.3 Thermal Resistance

4.3.1 PCB set up

Figure 4 2s2p PCB Cross Section

1) Test at TJ = -40°C only2) Not subject to production test. Specified by design.

Table 4 Thermal ResistanceParameter Symbol Values Unit Note /

Test ConditionNumber

Min. Typ. Max.Junction to soldering point RthJS – 5 – K/W 1)

1) Not subject to production test. Specified by design.

P_4.3.1Junction to ambient RthJA – 30 – K/W 1) 2)

2) Specified Rthja value is according to JEDEC JESD51-2,-5,-7 at natural convection on FR4 2s2p board; The product (chip + package) was simulated on a 76.4 x 114.3 x 1.5 mm board with 2 inner copper layers (2 x 70µm Cu, 2 x 35 µm Cu). Where applicable, a thermal via array under the exposed pad contacts the first inner copper layer. Please refer to Figure 4 and Figure 5.

P_4.3.2

1.5mm

70µm

35µm

0.3mm PCB 2s2p.vsd

BTS5008-1EKB



Figure 5 PC Board Top and Bottom View for Thermal Simulation with 600 mm² Cooling Area

4.3.2 Thermal Impedance

Figure 6 Typical Thermal Impedance. PCB set up according Figure 5

thermique SO14.vsd

1

2

3

4

5

6

7

14

13

12

11

10

9

8

COOLINGTAB

VS

PCB top view

PCB bottom view

0,01

0,1

1

10

100

0,0001 0,001 0,01 0,1 1 10 100 1000Time [s]

Zth [K/W

]

1s0p‐footprint

1s0p‐300mm²

1s0p‐600mm²

2s2p

RTHJA_BTS5008 _1EKA.vsd

BTS5008-1EKB



Figure 7 Typical Thermal Resistance. PCB set up 1s0p

0 100 200 300 400 500 600 70030

35

40

45

50

55

60

65

70

75

80

Rth

ja [K

/W]

Area [mm2]

footprint

1s0p

BTS5008-1EKB

Power Stage


5 Power StageThe power stages are built using an N-channel vertical power MOSFET (DMOS) with charge pump.

5.1 Output ON-state ResistanceThe ON-state resistance RDS(ON) depends on the supply voltage as well as the junction temperature TJ. Figure 8shows the dependencies in terms of temperature and supply voltage for the typical ON-state resistance. Thebehavior in reverse polarity is described in Chapter 6.4.

Figure 8 Typical ON-state Resistance

A high signal at the input pin (see Chapter 8) causes the power DMOS to switch ON with a dedicated slope, whichis optimized in terms of EMC emission.

5.2 Turn ON/OFF Characteristics with Resistive LoadFigure 9 shows the typical timing when switching a resistive load.

Figure 9 Switching a Resistive Load Timing

Rdson_8.vsd

0

4

8

12

16

-40 -10 20 50 80 110 140Junction Temperature (Tj)

RD

S(O

N) (m

Ω)

0

10

20

30

40

50

0 3 6 9 12 15 18Supply Voltage VS (V)

RD

S(O

N) (m

Ω)

IN

t

VOUT

tON

tON_DELAY tOFF

90% VS

10% VS

VIN_H

VIN_L

t

Switching times .vsd

tOFF_DELAY

30% VS

70% VS

dV/dt ON dV/dt OFF

BTS5008-1EKB

Power Stage


5.3 Inductive Load

5.3.1 Output ClampingWhen switching OFF inductive loads with high side switches, the voltage VOUT drops below ground potential,because the inductance intends to continue driving the current. To prevent the destruction of the device byavalanche due to high voltages, there is a voltage clamp mechanism ZDS(AZ) implemented that limits negativeoutput voltage to a certain level (VS - VDS(AZ)). Please refer to Figure 10 and Figure 11 for details. Nevertheless,the maximum allowed load inductance is limited.

Figure 10 Output Clamp

Figure 11 Switching an Inductive Load Timing

VBAT

VOUT

IL

L, RL

VS

OUT

VDS

LOGICIN

VIN

ZDS(AZ)

GND

ZGND

IN

VOUT

IL

VS

VS-VDS(AZ)

t

t

t

Switching an inductance.vsd

BTS5008-1EKB

Power Stage


5.3.2 Maximum Load Inductance

During demagnetization of inductive loads, energy has to be dissipated in the BTS5008-1EKB. This energy canbe calculated with following equation:

(1)

Following equation simplifies under the assumption of RL = 0 Ω.

(2)

The energy, which is converted into heat, is limited by the thermal design of the component. See Figure 12 for themaximum allowed energy dissipation as a function of the load current.

Figure 12 Maximum Energy Dissipation Single Pulse, TJ_START = 150 °C; VS = 13.5V

5.4 Inverse Current CapabilityIn case of inverse current, meaning a voltage VINV at the OUTput higher than the supply voltage VS, a current IINVwill flow from output to VS pin via the body diode of the power transistor (please refer to Figure 13). The outputstage follows the state of the IN pin, except if the IN pin goes from OFF to ON during inverse. In that particularcase, the output stage is kept OFF until the inverse current disappears. Nevertheless, the current IINV should notbe higher than IL(INV). If the channel is OFF, the diagnostic will detect an open load at OFF. If the affected channelis ON, the diagnostic will detect open load at ON (the overtemperature signal is inhibited). At the appearance ofVINV, a parasitic diagnostic can be observed. After, the diagnosis is valid and reflects the output state. At VINVvanishing, the diagnosis is valid and reflects the output state. During inverse current, no protection functions areavailable.

E VDS AZ( )LRL------×

VS VDS AZ( )–RL

-------------------------------- 1RL IL×

VS VDS AZ( )–--------------------------------–⎝ ⎠

⎛ ⎞ln IL+××=

E 12--- L I2 1

VS

VS VDS AZ( )–--------------------------------–⎝ ⎠

⎛ ⎞×××=

10

100

1000

0 2 4 6 8 10 12IL(A)

E AS (

mJ)

EAS8.vsd

BTS5008-1EKB

Power Stage


Figure 13 Inverse Current Circuitry

OUT

VS

VBAT

IL(INV)OL comp.

inverse current .vsd

VINV

INVComp.

Gatedriver

Devicelogic

GND

ZGND

BTS5008-1EKB

Power Stage


5.5 Electrical Characteristics Power Stage

Table 5 Electrical Characteristics: Power StageVS = 8 V to 18 V, TJ = -40 °C to +150 °C (unless otherwise specified).Typical values are given at VS = 13.5 V, TJ = 25 °C



ON-state resistance per channel

RDS(ON)_150 9 14 16 mΩ IL = IL4 = 10 A VIN = 4.5 V TJ = 150 °C See Figure 8

P_5.5.1

ON-state resistance per channel

RDS(ON)_25 – 8 – mΩ 1) TJ = 25 °C P_5.5.21

Nominal load current IL(NOM) – 11 – A 1) TA = 85 °C TJ < 150 °C

P_5.5.2

Output voltage drop limitation at small load currents

VDS(NL) – 6 25 mV IL = IL0 = 50 mA See Figure 33

P_5.5.4

Drain to source clamping voltage VDS(AZ) = [VS - VOUT]

VDS(AZ) 41 46.5 53 V IDS = 20 mA See Figure 11 See Figure 34

P_5.5.5

Output leakage current TJ ≤ 85 °C

IL(OFF) – 0.01 1.4 µA 2) VIN floating VOUT = 0 V TJ ≤ 85°C

P_5.5.6

Output leakage current TJ = 150 °C

IL(OFF)_150 – 5 54 µA VIN floating VOUT = 0 V TJ = 150 °C

P_5.5.8

Inverse current capability IL(INV) – 11 – A 1) VS < VOUTx P_5.5.9Slew rate 30% to 70% VS

dV/dtON 0.1 0.25 0.5 V/µs RL = 2 Ω VS = 13.5 V See Figure 9 See Figure 35 See Figure 36 See Figure 37 See Figure 38 See Figure 39

P_5.5.11

Slew rate 70% to 30% VS

-dV/dtOFF 0.1 0.25 0.5 V/µs P_5.5.12

Slew rate matching dV/dtON - dV/dtOFF

∆dV/dt -0.15 0 0.15 V/µs P_5.5.13

Turn-ON time to VOUT = 90% VS

tON 30 100 250 µs P_5.5.14

Turn-OFF time to VOUT = 10% VS

tOFF 30 100 250 µs P_5.5.15

Turn-ON / OFF matching tOFF - tON

∆tSW -50 5 50 µs P_5.5.16

Turn-ON time to VOUT = 10% VS

tON_delay 10 60 120 µs P_5.5.17

Turn-OFF time to VOUT = 90% VS

tOFF_delay 10 60 120 µs P_5.5.18

BTS5008-1EKB

Power Stage


Switch ON energy EON – 1.5 – mJ 1) RL = 2 Ω VOUT = 90% VS VS = 18 V See Figure 40

P_5.5.19

Switch OFF energy EOFF – 1.5 – mJ 1) RL = 2 Ω VOUT = 10% VS VS = 18 V See Figure 41

P_5.5.20

1) Not subject to production test, specified by design.2) Test at TJ = -40°C only

Table 5 Electrical Characteristics: Power Stage (cont’d)VS = 8 V to 18 V, TJ = -40 °C to +150 °C (unless otherwise specified).Typical values are given at VS = 13.5 V, TJ = 25 °C



BTS5008-1EKB

Protection Functions


6 Protection FunctionsThe device provides integrated protection functions. These functions are designed to prevent the destruction ofthe IC from fault conditions described in the data sheet. Fault conditions are considered as “outside” normaloperating range. Protection functions are designed for neither continuous nor repetitive operation.

6.1 Loss of Ground ProtectionIn case of loss of the module ground and the load remains connected to ground, the device protects itself byautomatically turning OFF (when it was previously ON) or remains OFF, regardless of the voltage applied on INpin.In case of loss of device ground, it’s recommended to use input resistors between the microcontroller and theBTS5008-1EKB to ensure switching OFF of channel.In case of loss of module or device ground, a current (IOUT(GND)) can flow out of the DMOS. Figure 14 sketchesthe situation.ZGND is recommended to be resistor in parrallel to diode.

Figure 14 Loss of Ground Protection with External Components

6.2 Undervoltage ProtectionBetween VS(UV) and VS(OP), the undervoltage mechanism is triggered. VS(OP) represents the minimum voltagewhere the switching ON and OFF can takes place. VS(UV) represents the minimum voltage the switch can hold ON.If the supply voltage is below the undervoltage mechanism VS(UV), the device is OFF (turns OFF). As soon as thesupply voltage is above the undervoltage mechanism VS(OP), then the device can be switched ON. When the switchis ON, protection functions are operational. Nevertheless, the diagnosis is not guaranteed until VS is in the VNOMrange. Figure 15 sketches the undervoltage mechanism.

IN0

DEN

IS

ZDESD GND

OUT

VS

VBATZD(AZ)

LOGIC

Loss of ground protection single.vsd

IOUT(GND)

ZDS(AZ)

IN1

RIN

RDEN

RSENSE

RIS

RGND

BTS5008-1EKB



Figure 15 Undervoltage Behavior

6.3 Overvoltage ProtectionThere is an integrated clamp mechanism for overvoltage protection (ZD(AZ)). To guarantee this mechanismoperates properly in the application, the current in the Zener diode has to be limited by a ground resistor. Figure 16shows a typical application to withstand overvoltage issues. In case of supply voltage higher than VS(AZ), the powertransistor switches ON and the voltage across the logic section is clamped. As a result, the internal groundpotential rises to VS - VS(AZ). Due to the ESD Zener diodes, the potential at pin IN and DEN rises almost to thatpotential, depending on the impedance of the connected circuitry. In the case the device was ON, prior toovervoltage, the BTS5008-1EKB remains ON. In the case the BTS5008-1EKB was OFF, prior to overvoltage, thepower transistor can be activated. In the case the supply voltage is in above VBAT(SC) and below VDS(AZ), the outputtransistor is still operational and follows the input. If the channel is in the ON state, parameters are no longerguaranteed and lifetime is reduced compared to the nominal supply voltage range. This especially impacts theshort circuit robustness, as well as the maximum energy EAS capability. ZGND is recommended to be a diode andresistor (1 kΩ).

Figure 16 Overvoltage Protection with External Components

undervoltage behavior .vsd

VOUT

VS(OP)VS(UV)VS

IN

DEN

IS

ZDESD GND

OUT

VS

VBATZD(AZ)

LOGIC

Overvoltage protection single.vsd

ZDS(AZ)

IN1

RIN

RDEN

RSENSE

RIS

RGND

ISOV

BTS5008-1EKB



6.4 Reverse Polarity ProtectionIn case of reverse polarity, the intrinsic body diodes of the power DMOS causes power dissipation. The current inthis intrinsic body diode is limited by the load itself. Additionally, the current into the ground path and the logic pinshas to be limited to the maximum current described in Chapter 4.1 with an external resistor. Figure 17 shows atypical application. RGND resistor is used to limit the current in the Zener protection of the device. Resistors RDENand RIN are used to limit the current in the logic of the device and in the ESD protection stage. RSENSE is used tolimit the current in the sense transistor which behaves as a diode. The recommended value for RDEN = RIN = RSENSE= 4.7 kΩ. ZGND is recommended to be 1 kΩ resistor in parallel to diode.During reverse polarity, no protection functions are available.

Figure 17 Reverse Polarity Protection with External Components

6.5 Overload ProtectionIn case of overload, such as high inrush of cold lamp filament, or short circuit to ground, the BTS5008-1EKB offersseveral protection mechanisms.

6.5.1 Current LimitationAt first step, the instantaneous power in the switch is maintained at a safe value by limiting the current to themaximum current allowed in the switch IL(SC). During this time, the DMOS temperature is increasing, which affectsthe current flowing in the DMOS. The current limitation value is VDS dependent. Figure 18 shows the behavior ofthe current limitation as a function of the drain to source voltage.

IN

DEN

IS

ZDESD GND

OUT

VS

VBAT

ZD(AZ)

LOGIC

Reverse Polarity single.vsd

ZDS(AZ)

IN0 RIN

RDEN

RSENSE

RIS RGND

-VDS(REV)

Micro controllerprotection

diodes

-IL(nom)

BTS5008-1EKB



Figure 18 Current Limitation (typical behavior)

6.5.2 Temperature Limitation in the Power DMOSThe channel incorporates both an absolute (TJ(SC)) and a dynamic (TJ(SW)) temperature sensor. Activation of eithersensor will cause an overheated channel to switch OFF to prevent destruction. Any protective switch OFF latchesthe output until the temperature has reached an acceptable value. Figure 19 gives a sketch of the situation. The∆TSTEP describes the device’s warming, due to the overcurrent in the channel.A retry strategy is implemented such that when the DMOS temperature has cooled down enough, the switch isswitched ON again, if the IN pin signal is still high (restart behavior).

40

50

60

70

80

90

100rr

ent L

imit

I L(S

C)(A

)

0

10

20

30

0 5 10 15 20 25

Cu

Drain source Voltage VDS (V)

BTS5008-1EKB



Figure 19 Overload Protection

Note: For better understanding, the time scale is not linear. The real timing of this drawing is application dependant and cannot be described.

IN

tIL

t

IL(x)SC

IIS

t0A

IIS(FAULT)

VDEN

t0V

TDMOS

t

ΔTSTEP

TA

ΔTJ(SW)ΔTJ(SW)

ΔTJ(SW)

Hard start .vsd

tsIS(FAULT)

IL(NOM)

IL(NOM) / kILIS

tsIS(OT_blank)

TJ(SC)

tsIS(OFF)

LOAD CURRENT LIMITATION PHASE LOAD CURRENT BELOW LIMITATION PHASE

BTS5008-1EKB



6.6 Electrical Characteristics for the Protection Functions

Table 6 Electrical Characteristics: ProtectionVS = 8 V to 18 V, TJ = -40 °C to +150 °C (unless otherwise specified).Typical values are given at VS = 13.5 V, TJ = 25 °C



Loss of GroundOutput leakage current while GND disconnected

IOUT(GND) – 0.1 – mA 1) 2) VS = 28 V See Figure 14

1) All pins are disconnected except VS and OUT.2) Not Subject to production test, specified by design

P_6.6.1

Reverse PolarityDrain source diode voltage during reverse polarity

VDS(REV) 200 650 700 mV IL = - 4 A TJ = 150 °C See Figure 17

P_6.6.2

OvervoltageOvervoltage protection VS(AZ) 41 46 53 V ISOV = 5 mA

See Figure 16P_6.6.3

Overload ConditionLoad current limitation IL5(SC) 65 75 105 A 3)VDS = 5 V

See Figure 18See Figure 42

3) Test at TJ = -40°C only

P_6.6.4

Load current limitation IL28(SC) – 45 – A 2) VDS = 28 V See Figure 18See Figure 43

P_6.6.7

Short circuit current during over temperature toggling

IL(RMS) – 8.6 – A 2) VIN = 4.5 V RSHORT = 100 mΩ LSHORT = 5 µH

P_6.6.12

Dynamic temperature increase while switching

∆TJ(SW) – 80 – K 4) See Figure 19

4) Functional test only

P_6.6.8

Thermal shutdown temperature

TJ(SC) 150 170 4) 200 4) °C 5) See Figure 19

5) Test at TJ = +150°C only

P_6.6.10

Thermal shutdown hysteresis ∆TJ(SC) – 20 – K 5) 4) See Figure 19 P_6.6.11

BTS5008-1EKB

Diagnostic Functions


7 Diagnostic FunctionsFor diagnosis purpose, the BTS5008-1EKB provides a combination of digital and analog signals at pin IS. Thesesignals are called SENSE. In case the diagnostic is disabled via DEN, pin IS becomes high impedance. In caseDEN is activated, the sensed current of the channel is enabled.

7.1 IS PinThe BTS5008-1EKB provides a SENSE current written IIS at pin IS. As long as no “hard” failure mode occurs (shortcircuit to GND / current limitation / overtemperature / excessive dynamic temperature increase or open load atOFF) a proportional signal to the load current (ratio kILIS = IL / IIS) is provided. The complete IS pin and diagnosticmechanism is described on Figure 20. The accuracy of the sense current depends on temperature and loadcurrent. Due to the ESD protection, in connection to VS, it is not recommended to share the IS pin with otherdevices if these devices are using another battery feed. The consequence is that the unsupplied device would befed via the IS pin of the supplied device.

Figure 20 Diagnostic Block Diagram

Vs

IIS(FAULT)

IIS = IL / kILIS

DEN

IS

S ense schematic s ingle.svg

1

0

0

1

FAULT

ZIS(AZ)

BTS5008-1EKB



7.2 SENSE Signal in Different Operating ModesTable 7 gives a quick reference for the state of the IS pin during device operation.

Table 7 Sense Signal, Function of Operation ModeOperation Mode Input level Channel X DEN Output Level Diagnostic OutputNormal operation OFF H Z ZShort circuit to GND ~ GND ZOvertemperature Z ZShort circuit to VS VS IIS(FAULT)

Open Load < VOL(OFF)> VOL(OFF)

1)

1) Stable with additional pull-up resistor.

ZIIS(FAULT)

Inverse current ~ VINV IIS(FAULT)

Normal operation ON ~ VS IIS = IL / kILIS

Current limitation < VS IIS(FAULT)

Short circuit to GND ~ GND IIS(FAULT)

Overtemperature TJ(SW) event

Z IIS(FAULT)

Short circuit to VS VS IIS < IL / kILIS

Open Load ~ VS2)

2) The output current has to be smaller than IL(OL).

IIS < IIS(OL)

Inverse current ~ VINV IIS < IIS(OL)3)

3) After maximum tINV.

Underload ~ VS4)

4) The output current has to be higher than IL(OL).

IIS(OL) < IIS < IL / kILIS

Don’t care Don’t care L Don’t care Z

BTS5008-1EKB



7.3 SENSE Signal in the Nominal Current RangeFigure 21 and Figure 22 show the current sense as a function of the load current in the power DMOS. Usually, apull-down resistor RIS is connected to the current sense IS pin. This resistor has to be higher than 560 Ω to limitthe power losses in the sense circuitry. A typical value is 1.2 kΩ. The blue curve represents the ideal sensecurrent, assuming an ideal kILIS factor value. The red curves shows the accuracy the device provide across fulltemperature range, at a defined current.

Figure 21 Current Sense for Nominal Load

7.3.1 SENSE Signal Variation as a Function of Temperature and Load CurrentIn some applications a better accuracy is required around half the nominal current IL(NOM). To achieve this accuracyrequirement, a calibration on the application is possible. To avoid multiple calibration points at different load andtemperature conditions, the BTS5008-1EKB allows limited derating of the kILIS value, at a given point (IL3; TJ =+25 °C). This derating is described by the parameter ∆kILIS. Figure 22 shows the behavior of the sense current,assuming one calibration point at nominal load at +25 °C. The blue line indicates the ideal kILIS ratio.The red lines indicate the derating on the parameter across temperature and voltage, assuming one calibrationpoint at nominal temperature and nominal battery voltage.The grey lines indicate the kILIS accuracy without calibration.

0 1 2 3 4 5 6 7 8 9 100

0.5

1

1.5

2

2.5

IL [A]

I IS [m

A]

min/max Sense Currenttypical Sense Current

BTS5008-1EKB

BTS5008-1EKB



Figure 22 Improved Current Sense Accuracy with One Calibration Point at 4A

7.3.2 SENSE Signal TimingFigure 23 shows the timing during settling and disabling of the sense.

Figure 23 Current Sense Settling / Disabling Timing

0 1 2 3 4 5 6 7 8 9 102500

3000

3500

4000

4500

5000

5500

6000

6500

7000

7500

IL [A]

k ILIS

calibrated kILIS

min/max kILIS

typical kILIS

BTS5008-1EKB

VIN

tIL

t

IIS

t

VDEN

t

TsIS(ON)tsIS(OFF)

tON

90% ofIIS static

90% ofIL static

TsIS(ON)

TsIS(LC)

current sense settling disabling time single.vsd

BTS5008-1EKB



7.3.3 SENSE Signal in Open Load

7.3.3.1 Open Load in ON DiagnosticIf the channel is ON, a leakage current can still flow through an open load, for example due to humidity. Theparameter IL(OL) gives the threshold of recognition for this leakage current. If the current IL flowing out the powerDMOS is below this value, the device recognizes a failure, if the DEN is selected. In that case, the SENSE currentis below IIS(OL). Otherwise, the minimum SENSE current is given above parameter IIS(OL). Figure 24 shows theSENSE current behavior in this area. The red curve shows a typical product curve. The blue curve shows the idealcurrent sense ratio.

Figure 24 Current Sense Ratio for Low Currents

7.3.3.2 Open Load in OFF DiagnosticFor open load diagnosis in OFF-state, an external output pull-up resistor (ROL) is recommended. For thecalculation of pull-up resistor value, the leakage currents and the open load threshold voltage VOL(OFF) have to betaken into account. Figure 25 gives a sketch of the situation. Ileakage defines the leakage current in the completesystem, including IL(OFF) (see Chapter 5.5) and external leakages, e.g, due to humidity, corrosion, etc.... in theapplication.To reduce the stand-by current of the system, an open load resistor switch SOL is recommended. If the channel xis OFF, the output is no longer pulled down by the load and VOUT voltage rises to nearly VS. This is recognized bythe device as an open load. The voltage threshold is given by VOL(OFF). In that case, the SENSE signal is switchedto the IIS(FAULT).An additional RPD resistor can be used to pull VOUT to 0V. Otherwise, the OUT pin is floating. This resistor can beused as well for short circuit to battery detection, see Chapter 7.3.4.

IIS

IL

Sense for OL .vsd

IL(OL)

IIS(OL)

BTS5008-1EKB



Figure 25 Open Load Detection in OFF Electrical Equivalent Circuit

7.3.3.3 Open Load Diagnostic TimingFigure 26 shows the timing during either Open load in ON or OFF condition. Please note that a delay tsIS(OT_BLANK)has to be respected between the falling edge of the input and rising edge of the DEN, when applying an open loadin OFF diagnosis request, otherwise the voltage VOUT cannot be guaranteed and the diagnosis can be wrong.

Figure 26 SENSE Signal in Open Load Timing

OUT

VS

SOL

Vbat

VOL(OFF)

Ileakage

IIS(FAULT)

ISILOFF

OLcomp.

Open Load in OFF.vsd

ROL

RGNDRIS

Rleakage

GND

VIN

tVOUT

t

IIS

t

VDEN

t

tsIS(LC)

90% of IIIS(FAULT) static

tsIS(FAULT_OL_OFF)

Error Settling Disabling Time .vsd

VOL(OFF)

RDSON x IL

IOUT

tsIS(OT_BLANK)

Load is present Open load

BTS5008-1EKB



7.3.4 SENSE Signal with OUT in Short Circuit to VSIn case of a short circuit between the OUTput-pin and the VS pin, all or portion (depending on the short circuitimpedance) of the load current will flow through the short circuit. As a result, a lower current compared to thenormal operation will flow through the DMOS of the BTS5008-1EKB, which can be recognized at the SENSEsignal. The open load at OFF detection circuitry can also be used to distinguish a short circuit to VS. In that case,an external resistor to ground RSC_VS is required. Figure 27 gives a sketch of the situation.

Figure 27 Short Circuit to Battery Detection in OFF Electrical Equivalent Circuit

7.3.5 SENSE Signal in Case of OverloadAn overload condition is defined by a current flowing out of the DMOS reaching the current limitation and / or theabsolute dynamic temperature swing TJ(SW) is reached, and / or the junction temperature reaches the thermalshutdown temperature TJ(SC). Please refer to Chapter 6.5 for details.In that case, the SENSE signal given is by IIS(FAULT) when the diagnostic is selected.The device has a thermal restart behavior, such that when the overtemperature or the exceed dynamictemperature condition has disappeared, the DMOS is reactivated if the IN is still at logical level one. If the DENpin is activated, the IS pin is not toggling with the restart mechanism and remains to IIS(FAULT).

7.3.6 SENSE Signal in Case of Inverse CurrentIn the case of inverse current, the channel will indicate open load in OFF state and indicate open load in ON state.

VS

Vbat

VOL(OFF)

IIS(FAULT)

IS

OLcomp.

Short circuit to Vs.vsd

VBAT

OUT

GND

RGND RSC_VSRIS

BTS5008-1EKB



7.4 Electrical Characteristics Diagnostic Function

Table 8 Electrical Characteristics: DiagnosticsVS = 8 V to 18 V, TJ = -40 °C to +150 °C (unless otherwise specified).Typical values are given at VS = 13.5 V, TJ = 25 °C



Load Condition Threshold for DiagnosticOpen load detection threshold in OFF state

VS - VOL(OFF) 4 – 6 V VIN = 0 V VDEN = 4.5 V

P_7.5.1

Open load detection threshold in ON state

IL(OL) 7.5 18 45 mA VIN = VDEN = 4.5 V IIS(OL) = 4 μA See Figure 24 See Figure 45

P_7.5.2

Sense PinIS pin leakage current when sense is disabled

IIS_(DIS) – 0.01 1 µA VIN = 4.5 V VDEN = 0 V IL = IL4 = 10 A

P_7.5.4

Sense signal saturation voltage

VS - VIS

(RANGE)

0 2.2 3 V VIN = 0 V VOUT = VS > 10 V VDEN = 4.5 V IIS = 6 mA See Figure 46

P_7.5.6

Sense signal maximum current in fault condition

IIS(FAULT) 7 13 35 mA VIS = VIN = VDSEL = 0 V VOUT = VS > 10 V VDEN = 4.5 V See Figure 20See Figure 47

P_7.5.7

Sense pin maximum voltage VIS(AZ) 41 46 53 V IIS = 5 mA See Figure 20

P_7.5.3

Current Sense Ratio Signal in the Nominal Area, Stable Load Current ConditionCurrent sense ratio IL0 = 50 mA

kILIS0 -50% 5000 +50% VIN = 4.5 V VDEN = 4.5 V See Figure 21 TJ = -40 °C; 150 °C

P_7.5.8

Current sense ratio IL1 = 0.5 A

kILIS1 -40% 4500 +40% P_7.5.9

Current sense ratio IL2 = 2 A

kILIS2 -20% 4400 +20% P_7.5.10


kILIS3 -13% 4400 +13% P_7.5.11


kILIS4 -9% 4400 +9% P_7.5.12

kILIS derating with current and temperature

∆kILIS -8 0 +8 % 1) kILIS4 versus kILIS3 See Figure 22

P_7.5.16

BTS5008-1EKB



kILIS derating with current and temperature

∆kILIS -12 0 +12 % 1) kILIS3 versus kILIS2 P_7.5.17

Diagnostic Timing in Normal ConditionCurrent sense settling time to kILIS function stable after positive input slope on both INput and DEN

tsIS(ON) 0 – 250 µs 1) VDEN = VIN = 0 to 4.5 V VS = 13.5 V RIS = 1.2 kΩ CSENSE < 100 pF IL = IL3 = 4 A See Figure 23

P_7.5.18

Current sense settling time with load current stable and transition of the DEN

tsIS(ON_DEN) 0 – 20 µs VIN = 4.5 V VDEN = 0 to 4.5 V RIS = 1.2 kΩ CSENSE < 100 pF IL = IL3 = 4 A See Figure 23

P_7.5.19

Current sense settling time to IIS stable after positive input slope on current load

tsIS(LC) 0 – 50 µs VIN =VDEN = 4.5 V RIS = 1.2 kΩ CSENSE < 100 pF IL = IL2 = 2 A to IL = IL3 = 4 A ; See Figure 23

P_7.5.20

Diagnostic Timing in Open Load ConditionCurrent sense settling time to IIS stable for open load detection in OFF state

tsIS(FAULT_OL_

OFF)

0 – 200 µs VIN = 0V VDEN = 0 to 4.5 V RIS = 1.2 kΩ CSENSE < 100 pF VOUT = VS = 13.5 V See Figure 26

P_7.5.22

Diagnostic Timing in Overload ConditionCurrent sense settling time to IIS stable for overload detection

tsIS(FAULT) 0 – 250 µs VIN = VDEN = 0 to 4.5 V RIS = 1.2 kΩ CSENSE < 100 pF VDS = 5 V See Figure 19

P_7.5.24

Table 8 Electrical Characteristics: Diagnostics (cont’d)VS = 8 V to 18 V, TJ = -40 °C to +150 °C (unless otherwise specified).Typical values are given at VS = 13.5 V, TJ = 25 °C



BTS5008-1EKB



Current sense over temperature blanking time

tsIS(OT_BLANK) – 350 – µs 1) VIN = VDEN = 4.5 V RIS = 1.2 kΩ CSENSE < 100 pF VDS = 5 V to 0 V See Figure 19

P_7.5.32

Diagnostic disable timeDEN transition to IIS < 50% IL /kILIS

tsIS(OFF) 0 – 50 µs VIN = 4.5 V VDEN = 4.5 V to 0 V RIS = 1.2 kΩ CSENSE < 100 pF IL = IL3 = 4 A See Figure 23

P_7.5.25

1) Not subject to production test, specified by design

Table 8 Electrical Characteristics: Diagnostics (cont’d)VS = 8 V to 18 V, TJ = -40 °C to +150 °C (unless otherwise specified).Typical values are given at VS = 13.5 V, TJ = 25 °C



BTS5008-1EKB

Input Pins


8 Input Pins

8.1 Input CircuitryThe input circuitry is compatible with 3.3 and 5 V microcontrollers. The concept of the input pin is to react to voltagethresholds. An implemented Schmidt trigger avoids any undefined state if the voltage on the input pin is slowlyincreasing or decreasing. The output is either OFF or ON but cannot be in a linear or undefined state. The inputcircuitry is compatible with PWM applications. Figure 28 shows the electrical equivalent input circuitry. In case thepin is not needed, it must be left opened, or must be connected to device ground (and not module ground) via aninput resistor.

Figure 28 Input Pin Circuitry

8.2 DEN PinThe DEN pinenable and disable the diagnostic functionality of the device. The pin have the same structure as theINput pin, please refer to Figure 28.

8.3 Input Pin VoltageThe IN and DEN use a comparator with hysteresis. The switching ON / OFF takes place in a defined region, setby the thresholds VIN(L) Max. and VIN(H) Min. The exact value where the ON and OFF take place are unknown anddepends on the process, as well as the temperature. To avoid cross talk and parasitic turn ON and OFF, ahysteresis is implemented. This ensures a certain immunity to noise.

GND

IN

Input circuitry.vsd

BTS5008-1EKB

Input Pins


8.4 Electrical Characteristics

Table 9 Electrical Characteristics: Input PinsVS = 8 V to 18 V, TJ = -40 °C to +150 °C (unless otherwise specified).Typical values are given at VS = 13.5 V, TJ = 25 °C



INput Pins CharacteristicsLow level input voltage range VIN(L) -0.3 – 0.8 V See Figure 48 P_8.4.1High level input voltage range VIN(H) 2 – 6 V See Figure 49 P_8.4.2Input voltage hysteresis VIN(HYS) – 250 – mV 1) See Figure 50

1) Not subject to production test, specified by design

P_8.4.3Low level input current IIN(L) 1 10 25 µA VIN = 0.8 V P_8.4.4High level input current IIN(H) 2 10 25 µA VIN = 5.5 V

See Figure 51P_8.4.5

DEN PinLow level input voltage range VDEN(L) -0.3 – 0.8 V – P_8.4.6High level input voltage range VDEN(H) 2 – 6 V – P_8.4.7Input voltage hysteresis VDEN(HYS) – 250 – mV 1) P_8.4.8Low level input current IDEN(L) 1 10 25 µA VDEN = 0.8 V P_8.4.9High level input current IDEN(H) 2 10 25 µA VDEN = 5.5 V P_8.4.10

BTS5008-1EKB

Characterization Results


9 Characterization ResultsThe characterization have been performed on 3 lots, with 3 devices each. Characterization have been performedat 8 V, 13.5 V and 18 V, from -40°C to 150°C. When no dependency to voltage is seen, only one curve (13,5V) issketched.

9.1 General Product Characteristics

9.1.1 Minimum Functional Supply VoltageP_4.2.3

Figure 29 Minimum Functional Supply Voltage VS(OP)_MIN = f(TJ)

9.1.2 Undervoltage ShutdownP_4.2.4

Figure 30 Undervoltage Threshold VS(UV) = f(TJ)

4,3

4,4

4,5

4,6

4,7

4,8

4,9

5

nalSup

plyVo

ltageV

S(OP)_M

IN(V)

3,8

3,9

4

4,1

4,2

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Minim

umFun

ctio

JunctionTemperatureTJ (°C)

3,2

3,3

3,4

3,5

3,6

3,7

3,8

3,9

4

4,1

dervoltatgeShutdo

wnV

S(UV)(V)

2,6

2,7

2,8

2,9

3

3,1

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Und


BTS5008-1EKB



9.1.3 Current Consumption Channel activeP_4.2.5

Figure 31 Current Consumption for Whole Device with Load. One Channel Active IGND_1 = f(TJ;VS)

9.1.4 Standby Current for Whole Device with LoadP_4.2.7, P_4.2.10

Figure 32 Standby Current for Whole Device with Load. IS(OFF) = f(TJ;VS)

9.2 Power Stage

9.2.1 Output Voltage Drop Limitation at Low Load CurrentP_5.5.4

3

4

5

6

ptionCh

anne

lActiveI G

ND_1(m

A)

1

2

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Curren

tCon

sump


0,8

1

1,2

1,4

1,6

1,8

2

akageCu

rren

tIS(OF

F)(μA)

8V

13V

18V

0

0,2

0,4

0,6

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Lea


BTS5008-1EKB



Figure 33 Output Voltage Drop Limitation at Low Load Current VDS(NL) = f(TJ) and VDS(NL) = f(VS)

9.2.2 Drain to Source Clamp VoltageP_5.5.5

Figure 34 Drain to Source Clamp Voltage VDS(AZ) = f(TJ)

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25ageDrop

Limita

tionV

DS(NL)(m

V)

1

2

3

4

5

6

7

8

9

10

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

OutputVolta


46

47

48

49

50

51

52

53

ourceClam

pingV

oltageV

DS(AZ)(V)

41

42

43

44

45

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

DraintoSo


BTS5008-1EKB



9.2.3 Slew Rate at Turn ONP_5.5.11

Figure 35 Slew Rate at Turn ON dV/dtON = f(TJ;VS), RL = 2 Ω

9.2.4 Slew Rate at Turn OFFP_5.5.12

Figure 36 Slew Rate at Turn OFF - dV/dtOFF = f(TJ;VS), RL = 2 Ω

9.2.5 Turn ONP_5.5.14

Figure 37 Turn ON tON = f(TJ;VS), RL = 2 Ω

0,3

0,4

0,5

eatTu

rnONdV

/dt O

N(V/μs)

18V

13V

8V

0,1

0,2

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

SlewRate


0,3

0,4

0,5

atTu

rnOFFdV/dt

OFF(V/μs)

18V

13V

8V

0,1

0,2

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

SlewRa

te


120

130

140

150

160

170

180

190

200

210

220

230

240

250

TurnONTim

etON

(μs)

18V

13V

8V

30

40

50

60

70

80

90

100

110

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150


BTS5008-1EKB



9.2.6 Turn OFFP_5.5.11

Figure 38 Turn OFF tOFF = f(TJ;VS), RL = 2 Ω

9.2.7 Turn ON / OFF matching

P_5.5.16

Figure 39 Turn ON / OFF matching ΔtSW = f(TJ;VS), RL = 2 Ω

120

130

140

150

160

170

180

190

200

210

220

230

240

250TurnOFFTim

et O

FF(μs)

18V

13V

8V

30

40

50

60

70

80

90

100

110

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150


10

5

0

5

10

15

20

25

30

35

40

45

50

ON/O

FFM

atching

t SW(μs)

18V

13V

8V

50

45

40

35

30

25

20

15

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

TurnO


BTS5008-1EKB



9.2.8 Switch ON EnergyP_5.5.19

Figure 40 Switch ON Energy EON = f(TJ;VS), RL = 2 Ω

9.2.9 Switch OFF Energy

P_5.5.20

Figure 41 Switch OFF Energy EOFF = f(TJ;VS), RL = 2 Ω

0,8

1

1,2

1,4

1,6

1,8

2

ONEn

ergyE

SW(m

J)

18V

13,5V

8V

0

0,2

0,4

0,6

,

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Switch


0,8

1

1,2

1,4

1,6

1,8

2

OFFEne

rgyE S

W(m

J)

18V

13,5V

8V

0

0,2

0,4

0,6

,

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Switch


BTS5008-1EKB



9.3 Protection Functions

9.3.1 Overload Condition in the Low Voltage AreaP_6.6.4

Figure 42 Overload Condition in the Low Voltage Area IL5(SC) = f(TJ;VS)

9.3.2 Overload Condition in the High Voltage AreaP_6.6.7

Figure 43 Overload Condition in the High Voltage Area IL28(SC) = f(TJ;VS)

80

85

90

95

100

105

Curre

ntLimita

tionI L5

(SC)

(A)

18V

13V

8V

65

70

75

80

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Load


35

40

45

50

55

Curren

tLim

itatio

nI L2

8(SC)(A)

18V

13V

8V

20

25

30

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Load

C


BTS5008-1EKB



9.4 Diagnostic Mechanism

9.4.1 Current Sense at no Load

Figure 44 Current Sense at no Load IIS = f(TJ;VS), IL = 0

9.4.2 Open Load Detection Threshold in ON StateP_7.5.2

Figure 45 Open Load Detection ON State Threshold IL(OL) = f(TJ;VS)

1,5

2

2,5

3

entS

enseatn

oload

(μA

)

8V

13,5V

18V

0

0,5

1

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Curre

TemperatureTJ (°C)

21

23

25

27

29

31

33

35

37

39

41

43

45

dDe

tectionTh

resholdI L

(OL)(m

A)

5

7

9

11

13

15

17

19

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Ope

nLoad


BTS5008-1EKB



9.4.3 Sense Signal Saturation VoltageP_7.5.6

Figure 46 Sense Signal Saturation Voltage VS - VIS(RANGE) = f(TJ;VS)

9.4.4 Sense Signal maximum CurrentP_7.5.7

Figure 47 Sense Signal Maximum Current in Fault Condition IIS(FAULT) = f(TJ;VS)

2

2,5

3

3,5ationVo

ltageV

SV

IS(V)

8V

13V

18V

1

1,5

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

SenseSignalSatur


17181920212223242526272829303132333435

alM

axim

umCurrentI

IS(FAU

LT)(mA)

67891011121314151617

40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

SenseSign


BTS5008-1EKB



9.5 Input Pins

9.5.1 Input Voltage Threshold ON to OFFP_8.4.1

Figure 48 Input Voltage Threshold VIN(L) = f(TJ;VS)

9.5.2 Input Voltage Threshold OFF to ONP_8.4.2

Figure 49 Input Voltage Threshold VIN(H) = f(TJ;VS)

Input_pin_low_voltage.vsd

0

0,5

1

1,5

2

-40 0 40 80 120 160

Junction Temp (°C)

V_IN

H(L

) (V)

I_IN(L) @ 8V

I_IN(L) @ 13.5V

I_IN(L) @ 18V

Input_pin_high_voltage.vsd

0

0,5

1

1,5

2

-40 0 40 80 120 160

Junction Temp (°C)

V_IN

H(H

) (V)

BTS5008-1EKB



9.5.3 Input Voltage HysteresisP_8.4.3

Figure 50 Input Voltage Hysteresis VIN(HYS) = f(TJ;VS)

9.5.4 Input Current High LevelP_8.4.5

Figure 51 Input Current High Level IIN(H) = f(TJ;VS)

0

100

200

300

400

-40 0 40 80 120 160

Junction Temp (°C)

V_IN

(HYS

) (m

V)

V_IN(HYS) @ 8V

V_IN(HYS) 13.5V

V_IN(HYS) @ 18V

Input_pin_voltage_hysteresis.vsd

0

5

10

15

20

25

-40 0 40 80 120 160

Junction Temp (°C)

I_IN

H(H

) (µA

)

Input_pin_high_current.vsd

BTS5008-1EKB

Application Information


10 Application Information

Note: The following information is given as a hint for the implementation of the device only and shall not be regarded as a description or warranty of a certain functionality, condition or quality of the device.

Figure 52 Application Diagram with BTS5008-1EKB

Note: This is a very simplified example of an application circuit. The function must be verified in the real application.

Table 10 Bill of MaterialReference Value PurposeRIN 4.7 kΩ Protection of the micro controller during overvoltage, reverse polarity

Guarantee BTS5008-1EKB channels OFF during loss of groundRDEN 4.7 kΩ Protection of the micro controller during overvoltage, reverse polarity

Guarantee BTS5008-1EKB channels OFF during loss of groundRPD 47 kΩ Polarization of the output

Improve BTS5008-1EKB immunity to electromagnetic noiseRIS 1.2 kΩ Sense resistorRSENSE 4.7 kΩ Overvoltage, reverse polarity, loss of ground. Value to be tuned with micro

controller specification. ROL 1.5 kΩ Ensure polarization of the BTS5008-1EKB output during open load in OFF

diagnostic

OUT

OUT

A/D

Vss

Vdd

Micro controller

IN0

DEN

ISGND

OUT0

Vs

VBAT

CSENSE

Application example single .svg

Z1

R/L cable

R/L cable

COUT0

RIN

RDEN

RA/D RSENSE

RISRGND

VDD

RPD

CVS

ROL

T1

D

Z2

BTS5008-1EKB

Application Information


10.1 Further Application Information

• Please contact us to get the pin FMEA• Existing App. Notes• For further information you may visit http://www.infineon.com/profet

RA/D 4.7 kΩ Protection of the micro controller during overvoltage, reverse polarityD BAS21 Protection of the BTS5008-1EKB during reverse polarityRGND 1 kΩ To keep the device GND at a stable potential during clampingZ1 7 V Zener diode Protection of the micro controller during overvoltageZ2 36 V Zener

diodeProtection of the device during overvoltage

T1 BC 807 Switch the battery voltage for open load in OFF diagnosticCSENSE 100 pF Sense signal filteringCVS 100 nF Filtering of the voltage spikes on the battery lineCOUT0 4.7 nF Protection of the BTS5008-1EKB during ESD and BCI

Table 10 Bill of Material (cont’d)

Reference Value Purpose

http://www.infineon.com/

BTS5008-1EKB

Package Outlines


11 Package Outlines

Figure 53 PG-DSO-14-47 EP (Plastic Dual Small Outline Package) (RoHS-Compliant)

Green Product (RoHS compliant)To meet the world-wide customer requirements for environmentally friendly products and to be compliant withgovernment regulations the device is available as a green product. Green products are RoHS-Compliant (i.ePb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).

PG-DSO-14-33,-40,-43 V02

0.12

-0.0

85

8˚ MAX.

0˚...8˚1.27

0.41±0.09 2)A-B0.2 M C 14xD

Seating Plane

(1.4

7)

1.7

MA

X.

Sta

nd O

ff

C C0.08

-0.1

0.1+0 8˚ MAX.

0˚...8˚

0.35 x 45˚

3.9±0.11)0.1 DC 2x

±0.250.64

6D D

±0.20.2 M

+0.0

60.

19

8˚ M

AX

.

A

1 7

814

BC0.1 A-B 2x

±0.18.65Index Marking

6.4

Bottom View

±0.25

±0.2

52.

65

71

14 8

2) Does not include dambar protrusion of 0.13 max.1) Does not include plastic or metal protrusion of 0.15 max. per side

3) JEDEC reference MS-012 variation BB

BTS5008-1EKB

Revision History


12 Revision History

Version Date Changes2.1 2015-02-17 update of P_7.5.10, P_7.5.11, P_7.5.12

changed figure 21 and 22 according to parameter updateupdate of P_7.5.17creation of P_7.5.16updated package drawing - figure 53

2.0 2012-04-17 Creation of the Data Sheet

Edition 2015-02-17Published byInfineon Technologies AG81726 Munich, Germany© 2015 Infineon Technologies AGAll Rights Reserved.

Legal DisclaimerThe information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party.

InformationFor further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com).

WarningsDue to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office.The Infineon Technologies component described in this Data Sheet may be used in life-support devices or systems and/or automotive, aviation and aerospace applications or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support automotive, aviation and aerospace device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.

http://www.infineon.com

PROFET™+ 12V BTS5008-1EKB · Automotive Power Data Sheet Rev. 2.1, 2015-02-17 BTS5008-1EKB Smart...

Documents

Transcript of PROFET™+ 12V BTS5008-1EKB · Automotive Power Data Sheet Rev. 2.1, 2015-02-17 BTS5008-1EKB Smart...