PROFESSIONAL TOOL COLLECTION - HK automotive SEAL RING PLIERS 油封拉拔鉗 Deigned to reach into...
Transcript of PROFESSIONAL TOOL COLLECTION - HK automotive SEAL RING PLIERS 油封拉拔鉗 Deigned to reach into...
HK AUTOMOTIVE SDN BHD (776948-A)
L O T 2, K G. PU L U D UK , O P P O SI T E B U N DU S A N C O M M ER C I AL C EN T R E, J A L A N B U N DU S A N, P EN A M P AN G , K O T A K I NA B A LU 8 83 0 0 S A B AH . EMAIL: [email protected] TEL: 088 722 590 FAX: 088 725 590
S peci al ized in : Wheel servi ci ng equi pment s, Hydr aul ic l i f t i ng equi pments, A ut o di agnost ic tool s &
sof tware , S afe ty test l ane equi pment , C ol l i si on r epai r equi pment , Lubr i cat i on & c leani ng
equi pment A nd Tool s & accessor i es.
2009 PROFESSIONAL TOOL COLLECTION
2| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
1014 / 10080 AUTOMOTIVE CAR CHECK (3 ~ 48V)
正負極驗電筆 ● Circuit tester with test lead for either passenger car or trucks.
● Check circuits between 3 ~ 48 volt.
● LED Display show polarity.
1002 / 10078 CAR LIGHT TESTER
驗電筆(普遍型) ● Sharped prove tip covered with brass protection cap.
● Check function of car lights faster and easier.
● Check range: 6, 12, 24V.
1013 / 10079 CONTINUITY TESTER
起子型驗電筆 ● Power on type test 6, 12, 24 volt circuits.
● For wire breaks, short, fuses, lamps, relays armatures, etc.
● 4” Inspection probe with point cover.
● 36” long 16-gauge wire with alligator clip.
1027 / 10092 ANTI-FREEZE TESTER
水箱水測試器 ● Avoid winter freeze-ups and summer boil-over.
● Test all permanent (Ethylene Glycol) solutions with radiator hot or cold.
● Two scales show freeze point of radiator solution and boiling point of summer
coolant.
1028 / 10093 BATTERY HYDROMETER (GLASS)
電瓶水比重器(玻璃) ● Test the battery in seconds.
● Color-coded float for easy reading.
- CAR REPAIR TOOL - ELECTRICAL SERIES
*Prices and specifications are subject to change without prior notice. |3
HKA Tools
1025 / 50113 DHC BATTERY LOAD TESTER
電磁測驗機
● Battery rating: 6 ~ 12V.
● Dimension: 180mm (W) x 85mm (D) x 300mm (H)
1015 / 10077 BATTERY CARRIER
電瓶提取器 ● Designed to protect soft-sided, sealed life time batteries.
● Padded rubber and grooved for better grip of battery.
● Vinyl handle for easy lift and carry.
● Fits all 4” to 7” (102mm ~ 178mm) batteries, including side post batteries.
4| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
3165 FUEL INJECTION PRESSURE TEST KIT
燃油壓力錶(全車系) ● The related adapter are suitable for American, Japanese and European system cars.
● That used on the test can be hooked up and tied into system (upon teed mounting is used, the surface must be water wet)
3004 / 10016 PROFESSIONAL VACUUM & FUEL TESTER
真空吸力錶 ● Large 3-1/2” diameter gauge with color-coded easy reading scales.
● Extra long heavy-duty rubber hoses and 14mm / 18mm manifold adapter.
● Check from worn or defective parts in fuel pumps, vacuum system.
3078 DOUBLE GAUGE CARBON CLEANER
雙錶點滴式積碳清洗器 ● To test the engine pressure first, and adjust the inlet
pressure to be the same as engine pressure, and then open the valve to start the clean work.
● Gauge pressure: 0 ~ 100psi (0 ~ 7kgf/cm2)
● Tank capacity: 20oz.
3003 / 10039 PETROL COMPRESSION TESTER
汽缸壓力錶(汽油) ● Easy reading 2-1/2” diameter rubber covered gauge feature color-coded
quadruple calibration with 0 ~ 300psi, 21kg/cm, 21bar & 2100kpa. ● 13” durable steel wire insert hose with 14mm / 18mm adapter.
● 6” heavy duty stem with universal rubber cone adapter fits all plug holes.
3141 DIESEL ENGINE COMPRESSION TESTER KIT
柴油汽缸壓力錶 ● This is generally the preferred test method and avoids damage to the
injector, and fuel system contamination. ● Gauge range: 0 ~ 1000psi/0 ~ 70 bar.
● Application: BMW, BENZ. CARBODIES, MITSUBISHI, CITROEN, NISSAN, DACIA,
OPEL, DAIHATSU, PEUGEOT, FIAT, RENAULT, FORD, ROVER, HOLDEN, SEAT, ISUZU, TOYOTA, LAND ROVER, VAUXHALL, LEYLAND / DAF, VOLKSWAGEN, MAZDA, VOLVO, ETC
- CAR REPAIR TOOL - ENGINE SERIES
*Prices and specifications are subject to change without prior notice. |5
HKA Tools
3055 / 10090 MECHANIC’S STETHOSCOPE (TWO WAY)
音診器 (雙用) ● Provides a fast and easy way to locate noises in engines or bearings and other moving parts.
● Aluminum alloy probe / needle for finding the exact location of specific noises.
● Instrument is shockproof.
● Ideal for pinpointing unusual vibration or suspected leaks (valves, piston
rings, gaskets, etc)
3008 / 10017
TIMING LIGHT
正時燈 ● Works on all 12V gasoline engines.
● High impact ABS Housing.
● Detachable heavy duty inductive pick up clamps and leads for easy operation
and replacement.
10036 UNIVERSAL PULLEY HOLDER
凸軸萬用支擋扳手
● A great time saver, this unique tool is designed to trap and hold bolt-on pulleys by the
mounting bolts on most applications.
3209 / 10037 UNIVERSAL CAMSHAFT PULLEY HOLDING TOOL
皮帶盤支擋扳手 ● Suitable to use when the space is limited.
● To change the parts easily for fitting the different cars.
● Jaw length: 72 / 95mm
● Jaw Depth: 18mm , Width: 4.4mm
10038 SERPENTINE BELT TOOL
惰輪皮帶調整扳手組 ● Releases tension on serpentine belts with spring
loaded idler pulley. ● Four sockets size: 13, 15, 16, 18mm
● 1/2”, 3/8” Dr.
6| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
3244 / 10035 BALANCER PULLER AND INSTALLER
正時皮帶盤拆卸器 ● A professional tool set for balancer replacement.
● Built in bearing makes balancer replacing job easy and
damage free. ● 4-slot puller plate plus 9 threaded adapters to fit on
balancers on most engine
3243 ONE MAN OPERATION - VALVE SPRING COMPRESSOR KIT
單人操作免拆式凡爾鉗
● Easy to use, operate by one person only.
● Recessed pocket on valve pusher allows
replacement retrieval of valve collets. ● Valve pusher: 22mm Φ
● Complete service tool kit for installation and removal of the valve spring without removal of cylinder head from the engine.
● Applicable: 12V, 16V, 20V and 24V engine.
3012 / 10025 VALVE SPRING COMPRESSOR KIT
免拆式凡爾鉗 ● For use on most foreign & Domestic engines; including AUDI, CHRYSLER, INFINITI, HONDA, HYUNDAI, LEXUS, MAZDA, MITSUBISHI, NISSAN, PORSCHER, SATURN, TOYOTA, VOLVO & VOLKSWAGEN.
3013 / 10002 VALVE SPRING COMPRESSOR
萬能凡爾鉗 ● Reversible jaw adaptor for multi-valve engines.
● Capacity 45 ~ 145mm, throated clearance 250mm big
window jaw adaptor for easy replacement of valve collets.
● Dual size in 25mm and 30mm diameter.
3205 / 10003
UNIVERSAL VALVE SPRING COMPRESSOR
雙壓式凡爾鉗 ● Suitable for use on multi-valve petrol & diesel engines
with deep seated valves. ● Also for use with OHC OHV & CVH engines.
● Jaw capacity of 55mm ~ 175mm.
● Throat depth: 165mm
- CAR REPAIR TOOL - ENGINE SERIES
*Prices and specifications are subject to change without prior notice. |7
HKA Tools
3022 / 10019 VALVE SEAL RING PLIERS
油封拉拔鉗 ● Deigned to reach into confined area for removal of valve seal.
● Serrated tip for better grasp of valve seal regardless of it configuration
3014 / 10117 NISSAN VALVE ADJUSTING TOOL
氣門墊片更換夾鉗組(NISSAN) ● For overhead camshaft engines using spacer shims.
● This unique tool has been designed to allow for easy
valve adjustment on all Nissan’s and many other overhead camshaft engine using spacer shims for valve adjustment in operation.
3015 / 10118 TOYOTA VALVE ADJUSTING TOOL
氣門墊片更換夾鉗組(TOYOTA) ● For overhead camshaft engines using spacer shims.
● This unique tool has been designed to allow for easy valve adjustment on all Toyota’s and many other overhead camshaft engine using spacer shims for valve adjustment in operation.
- / 10004 PISTON RING COMPRESSOR
活塞環 ● Self - locking ratchet pawl prevents premature release and allow positive
locking action.
Item Specification 3028 3” x 125mm
3029 3” x 175mm
3030 4” x 175mm
3064 / 10034 CLUTCH ALIGNMENT TOOL
離合器對孔校正器(鋁) ● Align single disc clutches on most vehicles, light truck and tractor.
● Properly aligns clutch plate by tapered cone fitting into pilot bushing or
bearing. ● Sizes: 0.587", 0.650", 0.673", 0.748", 0.787", 0.807", 0.981"
8| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
- / 10134 OIL FILTER WRENCH
鋼板碗型機油芯扳手
Item Model Size Point Suitable For 3245 WH-901 SW 64 m/m P-14 Toyota, Nissan
3246 WH-902 SW 67 m/m P-14 Ford, Mazda
3247 WH-903 SW 74 m/m P-14 BMW, Audi, VW, Opel, Austin
3248 WH-903-1 SW75 m/m P-14 GM, Chrysler
3249 WH-903-2 SW 74 m/m P-8 Fiat
3250 WH-903-3 SW 74 m/m P-15 Chrysler, GM, Rover 3251 WH-903-4 SW73 m/m P-14 Toyota, Nissan
3252 WH-903-5 SW 73 m/m P-30 GM, Ford
3253 WH-903-7 SW 72.8 m/m P-14 Toyota
3254 WH-903-8 SW 75 m/m P-15 Mazda, Ford 3255 WH-904 SW 79 m/m P-15 Nissan, Daihatsu, Ford
3256 WH-905 SW 73 m/m P-15 GM, Chrysler, Mitsubishi
3257 WH-906 SW 84 m/m P-18 Peugeot, Citroen, Renault
3258 WH-907 SW 89 m/m P-15 Honda, Mitsubishi
3259 WH-908 SW 91 m/m P-15 Toyota, Nissan 3260 WH-909 SW 92 m/m P-15 Honda, Toyota
3261 WH-910 SW 95 m/m P-15 GM, Ford, Chrysler, Alfa Romeo
3262 WH-910-1 SW 91 m/m P-12 Peugeot, Citroen, Renault
3263 WH-911 SW 76 m/m P-12 Ford, Mazda, Mitsubishi, Daihatsu
3264 WH-911-1 SW 79 m/m P-15 Honda, Nissan, Toyota
3265 WH-912 SW 86 m/m P-14 Mazda, Mitsubishi
3266 WH-913 SW 91 m/m P-15 GM, Ford, Chrysler, Lancia, Fiat
3267 WH-914 SW 101 m/m P-15 Daihatsu, Mazda, Mitsubishi, Toyota
Item Model Size Point Suitable For
3268 WH-901-1 SW 63-64 m/m P-14 Toyota 3269 WH-903L SW 74 m/m P-14 Benz/Smart
(Depth:32mm)
3270 WH-915 SW 87 m/m P-16 Volvo 3271 WH-916 SW 93 m/m P-14 BMW 7 Series
3272 WH-916-1 SW 93 m/m P-14 BMW E-46 3 Series
3273 WH-991 SW 100.5 m/m P-15 Mazda, Toyota, Fuso
3274 WH-992 SW 106 m/m P-15 European Series 3275 WH-993 SW 106 m/m P-16 Mitsubishi
3276 WH-994 SW 108 m/m P-16 Fuso, Hino
3277 WH-995 SW 110 m/m P-17 Toyota
3278 WH-996 SW 118 m/m P-16 Isuzu
- CAR REPAIR TOOL - ENGINE SERIES
*Prices and specifications are subject to change without prior notice. |9
HKA Tools
3091 / 10012 8” CHAIN OIL FILTER WRENCH
8“鏈式機油板手 ● All drpo forged of line quality.
● Range: 50 ~ 200mm
● Length: 8” (200mm)
3219 / 10013 STRAP WRENCH
皮帶式機油板手 ● Fit filters with a diameter of 25mm ~ 160mm
3125 / 10014 THREE JAW TWO WAY OIL FILTER WRENCH
三爪雙向機油蕊板手 ● Removes all oil filters from 2-1/2” ~ 4” in diameter.
● Use with 1/2”Dr Ratchet
● Size: Ranges: 2-1/2” ~ 4” (63mm ~ 102mm)
3043 722.6 BENZ TRANSMISSION DIPSTICK
賓士變速箱拆裝器 ● The tool is designed to measure the oil level of transmission.
● Full length: 1220mm
● Applicable: Transmission type 722.6
3044 722.7 BENZ TRANSMISSION DIPSTICK
賓士變速箱拆裝器 ● The tool is designed to measure the oil level of transmission.
● Full length: 920mm
● Applicable: Transmission type 722.7
10| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
3089 / 10088 CYLINDER HEAD LEAKAGE TESTER
引擎燃燒室測漏組(藥水型) ● For the testing for cooling systems.
● For the detection of damaged cylinder heads.
● For the easy detection of leakage in the connection between combustion chamber and cooling system on water-cooled engines (gas, diesel and engines).
● With reaction fluid.
3083 / 10026 1/2” X M9 CYLINDER HEAD BOLT
1/2“ X M9 12角輪軸套筒 ● The 100mm length allow easy access to recessed head bolts.
● Comes with 1/2”Dr for use with a torque wrench.
● Use for Toyota cylinder head bolt.
3084 / 10027 1/2” X R10 CYLINDER HEAD BOLT
1/2“ X R10 6角輪軸套筒
● The 140mm length allow easy access to recessed head bolts.
● Comes with 1/2”Dr for use with a torque wrench.
● Use for VW, Audi cylinder head bolt.
10028 UNIVERSAL HOSE CLAMP REMOVER
可彎式喉式管束夾鉗 ● For replacement of fuel, oil and water hose.
● Hose clamp with flexible 600mm wire.
● Convenient for working hidden areas and long
distance. ● Patent.
3192 178MM ENGINE CYLINDER HONE
引擎三爪內徑研磨器
● Range: 3/4” ~ 2-1/2” (19 ~ 64mm)
● Stone size: 28.5 x 5 x 3 (3pcs) #3192-1.
● Collar prevents stone breakage
● Sleeve makes insertion in cylinder easy and
protects stones when not in use.
- CAR REPAIR TOOL - ENGINE SERIES
*Prices and specifications are subject to change without prior notice. |11
HKA Tools
3052 / 10031 HOSE REMOVER PLIER
油管分離鉗 ● For easy removal of 5/32” to 1/2” vacuum and fuel hoses.
● Fit the jaws on the tube with black jaw on the tube and silver jaw on the
hose. ● Squeeze to push the hose off the tube.
8094 / 10029 HOSE CLAMP PLIERS
直型喉式管束鉗
● Keep wire clamps spread open and free both hands.
● Finger tip "position lock" makes it easy to replace the lower radiator hose.
● Fits most size clamps.
8095 / 10030 CURVED HOSE CLAMP PLIERS
彎型喉式管束鉗 ● Finger tip “Position lock” to keep hose clamps
spread open.
● Convenient for replacement of lower radiator hose.
● 45° degree to fit some clamp in deep position.
3020 / 10119 2PCS HOSE REMOVER PLIER
油管分離起子 ● Special designed to remove the hose easily.
3019 / 10043 SEAL PULLER
油封拉拔器(雙頭大型) ● Remove oil & grease seals.
● Two tips fit most application.
12| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
3025 / 10024 5PC MINIATURE HOOK AND PICK SET
5PC 油封拉拔器支組(小型) ● Stainless steel points.
● Set contain saw, hook tool, 45° & 90° bent tool.
● Use for detail works and scribing, picking jobs.
3128 / 10120 OXYGEN SENSOR SOCKET
含氣感應器套筒(歐規) ● 3/8”Dr x 7/8” (22mm) flare nut socket for vacuum
switch & oxygen sensor service on computer controlled engine.
3210 / 10032 22MM (7/8”) x 1/2“DR OXYGEN SENSOR SOCKET
含氣感應器套筒 ● 1/2”DR 7/8” (22mm) x 90mm long, 7mm slot for oxygen sensor socket on
Japanese cars Ford, GM, Chrysler & Other cars.
10082 A/C CONPRESSOR CLUTCH REMOVER KIT
壓縮機培令拆裝組 ● Replace clutches found on FS6, C171, 6P & 148 computer.
● Also GM R4 & R6, HR-6, DA-6 & V5 A/C compressors.
● And compressors of Sanden SD505, 507, 508, 510, 575, 708 and 709.
● 2 & 3 hole puller plate fits most clutches, the mechanical force does the pulling job.
3116 / 10081 A/C SPRING LOCK COUPLING TOOL
冷氣快速接頭拆卸組(4PC) ● Used on 198 and the current Ford cars and pickup having spring lock connection on the A/C system.
● For 3/8”, 1/2”, 5/8” and 3/4” couplers.
- ENGINE SERIES
- CAR REPAIR TOOL - ENGINE SERIES
*Prices and specifications are subject to change without prior notice. |13
HKA Tools
3050 UNIVERSAL RADIATOR PRESSURE TESTER KIT(14pcs)
14支組水箱壓力錶 ● Made from aluminium.
● To test cooling system leakage.
● Contents: * 0. Temperature * 1. Pressure testing pump with gauge. * 2. GM (Cadilac) * 3. Benz, GM(Buick), Jeep * 4. Peugeot, Subaru, Chrysler, Acura, GM (Nova, Spectrum, Sprint), Mitsubishi, Nissan, Mazda, Toyota, Infiniti, GEO, Suzuki, Isuzu. * 5. Honda, Toyota, Suzuki, Mitsubishi, Chrysler, Acura. * 6. Benz (ML-Class), GM (Achiva, Skylark, Grmd am - 1992 ~ 2002), * 7. Volvo, Saab, Sterling, Citroen, Renault, Flat, Alfa, Jeep. * 8. VW (Vento, T4, Passat - 1996, Golf, Beetle, Sharan). * 9. Audi (A4, A5, A6), BMW 345, VW (Passa 1997 ~ 2002). *10. BMW. *11. Audi, VW. *12. Ford, International, Land Rover, Opel, Jaguar. *13. Benz (C-Class, E-Class, S-Class).
14| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
9043 / 10000 270MM COIL SPRING COMPRESSOR
270MM捲型彈簧壓縮器 ● Heat treated drop forged CR-V steel jaws & leaded screws (270mm)
● The tool is designed for use in limited space under wheel arch.
● Specially designed claws to wrap on coil spring safety.
● Maximum jaw opening is 270mm.
9044 / 10001
370MM COIL SPRING COMPRESSOR
370MM捲型彈簧壓縮器 ● Heat treated drop forged CR-V steel jaws & leaded screws
(370mm) ● The tool is designed for use in limited space under wheel
arch. ● Specially designed claws to wrap on coil spring safety.
● Maximum jaw opening is 370mm.
9016 PROFESSIONAL COIL SPRING COMPRESSOR
免拆式避震器彈簧壓縮器 ● Spring compressor are multi-application tools specifically.
● Developed for modern Macpherson suspensions, using a
range of 3 set of interchangeable forks.
9021 / 10044 16” BALL JOINT SEPARATOR
插式橫拉杆頭拔卸器(小車) ● Tempered drop forged steel one piece construction for long & rough usage.
● 21/32” (18mm) fork, 16” (410mm) length replaces worn out tie rods easily with a hammer striking. ● Also can separate shock absorber links.
9020 / 10045 12” BALL JOINT SEPARATOR
插式橫拉杆頭拔卸器(大車) ● Tempered drop forged steel one piece construction for long & rough usage.
● 15/16” (24mm) fork, 11-7/8” (300mm) length replaces worn out tie rods easily with a hammer striking.
● Also can remove CV drive shafts on FWD vehicle.
- CAR REPAIR TOOL - UNDERCAR SERIES
*Prices and specifications are subject to change without prior notice. |15
HKA Tools
9019 / 10009 BALL JOINT SEPARATOR(F1954)
橫拉杆球頭拔卸器(日規) ● Heat treated drop forged steel body & bolt for long rough usage.
● Spread ball joints easily where space prevents use of direct action method.
● Jaw open: 19mm.
9039 / 10008 UNIVERSAL BALL JOINT EXTRACTOR
雙調式橫拉杆球頭拔卸器 ● For splitting track-rod ends, anti-roll bar mounting, ball joints, etc.
● Jaw opening: 22mm.
9001 / 10040 UNIVERSAL BALL JOINT SEPARATOR
橫拉杆球頭拔卸器(歐規) ● Special design 2-stage operating suits most cars and light trucks ball joints in steering & suspension. ● Offset lever permits maximum jaw opening in 30mm & 56mm.
● Jaw open: 22mm.
10041 UNIVERSAL BALL JOINT PULLER
雙用式橫拉桿球頭拔卸器(小型) ● Special steel for removing the ball pivots on steering.
● Jaw open: 17mm
10042 UNIVERSAL BALL JOINT PULLER
雙用式橫拉桿球頭拔卸器(大型) ● Special steel for removing the ball pivots on steering arms, steering tie rocks,
steering knuckles, etc. ● Jaw open: 20mm.
16| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
9032 / 10048 HUB SLIDE HAMMER PULLER
輪軸滑鎚組(五孔) ● Pull flange type rear axles on most late model passenger car and light trucks.
● Designed to fit axles with bolts and stud up to 9/16”dia.
10049 HUB SLIDE HAMMER PULLER
輪軸滑鎚組(四孔) ● Pulls 4 bolts front hub easily with the 10 lb slide hammer.
● Heavy duty tool for rugged jobs.
9051 / 10057 UNIVERSAL AXLES SLIDE HAMMER SET
通用型滑鎚組(雙盤) ● Increase the coverage with the two axle puller.
● Include 3-Jaw puller and many types of joints.
● Slide hammer design for removing hub and
repairing dent, etc.
9023 / 10046 C.V JOINT BANDING TOOL (WITH CUTTER)
型防塵套束裝器(切斷型) ● Easily remove by sliding sideways after winding has been complete.
● Instruction: Place band around boot and through nose of tool and through slot in winding body. Using a 1/2” socket wrench or by hand wind the band until sufficient is applied. Rotate handle over the boot to lock the band. Slide tool free-end down with a hammer
9012 / 10051 INNER TIE ROD TOOL (12PCS)
方向機舵桿扳手組(12PCS) ● Works on the inner tie rods with inaccessible wrench flats.
● Many inner tie rod end sockets do not have a complete hex on the full length of the socket.
● The rounded socket ends prevents access to the wrench flats. Twelve crows feet.
- CAR REPAIR TOOL - UNDERCAR SERIES
*Prices and specifications are subject to change without prior notice. |17
HKA Tools
9049 / 10052 MULTI PURPOSE INNER TIE ROD TOOL
方向機舵桿扳手(通用型) ● The master tie rod tool easily replace inner tie rod ends without removing the rack and pinion.
● Capacity: 33mm ~ 42mm.
9013 CAR CAMBER ALIGNMENT TOOL
仰角校正器組
● With 4pcs Alignment plates.
● Hydraulic function.
● Suit for most cars.
9014 / 10053 FIXED MAGNETIC CAMBER GAUGE
磁式水平表 ● Accurate camber measuring tool for use after repair or replacement of struts, wheel assembles, etc.
● Vials housed in a durable non-magnetic casing with a magnetic head that attached firmly to rotors or spindles. ● Range: 5° positive to 5° negative in 1/2” increments.
9069 / 10070 PITMAN ARM PULLER (S)
大車橫拉桿球頭拔卸器(小型) ● Heavy duty forged alloy steel yoke.
● Heated treated center screw.
● Remove tie rod ends and pitman arm assemblies
from many light trucks. ● Opening size: 27mm.
● Pull travel: 45mm.
9070 / 10071 PITMAN ARM PULLER (B)
大車橫拉桿球頭拔卸器(大型) ● Heavy duty forged alloy steel yoke.
● Heated treated center screw.
● Remove tie rod ends and pitman arm assemblies
from many light trucks. ● Opening size: 33mm.
● Pull travel: 64mm.
18| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
9071 / 10072 OUTER TIE ROD REMOVER
兩爪活動橫拉杆拔卸器 ● Two adjustable jaws special designed for removing most models of outer tie rod.
● Material: SCM420 Hardened 42°.
BEARING SEPARATOR
培令拔卸器
● Made by SCM440 (CR-Mo) material.
Item Specification
9053 10mm ~ 30mm
9054 30mm ~ 50mm
9055 50mm ~ 75mm 9056 75mm ~ 100mm
9057 100mm ~ 150mm
9058 150mm ~ 200mm
9059 / 10059 BEARING SEPARATOR SET (708)
小型培令拔卸組(雙盤) ● Include bearing separator #EUS 9054 and #EUS 9055
● Pull out the bearing with the H-Type beam and bolts.
9062 / 10060 HYDRAULIC BEARING SEPARATOR PULLER KIT
大型油壓式培令拔卸組 ● Include bearing separator #EUS 9057.
● Effort saving with the hydraulic screw.
● Pull out the bearing with the H-Type beam and bolts.
9063 / 10061 HYDRAULIC BEARING SEPARATOR PULLER KIT
方向機舵桿扳手組(12PCS) ● Pull out the bearing with the H-type beam and bolts.
● Use with Item 9058 together is better.
- CAR REPAIR TOOL - UNDERCAR SERIES
*Prices and specifications are subject to change without prior notice. |19
HKA Tools
9002 / 10058 HYDRAULIC GEAR PULLER SET
綜點型油壓拔卸器 ● For agriculture machine, automotive and industry use.
● Hydraulic ram included for laborsaving.
● Material: SCM415 hardened 40° - 45°
9099 / 10055 BLIND HOLE BEARING PULLER SET
內孔培令滑鎚組 ● Use on steering wheels with tapped holes.
● Include two and three way york, pressure screw
and adaptor plus four set of studs.
9030 / 10056 3 JAW INTERNAL & EXTERNAL PULLER SET
三爪內、外孔培令滑鎚組 ● Size: Small of internal puller: 15mm ~ 30mm, Large of internal puller: 30mm ~ 80mm, External of internal puller: 15mm ~ 80mm.
9100 / 10073 ADJUSTABLE WHEEL BEARING LOCK NUT WRENCH
後軸螺帽拆卸器(通用型) ● Adjustable jaws with locking feature to suit both hexagon and octagon wheel bearing lock nuts.
● Include three set of pins for lock nuts with pin holes.
● Capacity: 6PT lock nuts: 1-3/4” to 5/3/4” (49 - 135mm)
8PT lock nits: 1-3/4” to 5/5/8” (49 - 143mm) Pin diameters: 1/4” (6mm), 5/16” (8mm), 3/8” (10mm).
9046 / 10089 STEERING WHEEL REMOVER /LOCK PLATE COMPRESSOR SET
方向盤及內圓盤拆卸器組(附雙勾) ● Removing steering wheels of most vehicles with or without telescoping it.
● Steering columns is easy with this new set.
● The steering wheel lock plate compressor is also included, to compress the steering wheel lock to remove or install the snap ring.
20| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
9047 / 10050 STEERING WHEEL PULLER SET
雙盤面方向盤拆卸器 ● One flange type puller for removal of parts with 2 or 3 tapped holes, including harmonic balancers and timing gears.
● Another special puller for steering wheels, pulley and flywheel.
- / 10011 KWT ARMATURE BEARING PULLER
培林拔卸器 Item Model Range
9104 AB 1 19mm ~ 35mm
9105 AB 2 24mm ~ 55mm 9106 AB 3 35mm ~ 80mm
- / 10006 TWO JAW BEARING PULLER
二爪培林拔卸器 Item Size Range
9107 4” 50mm ~ 102mm 9108 6” 60mm ~ 152mm
9109 8” 80mm ~ 203mm
- / 10007 THREE JAW BEARING PULLER
三爪培林拔卸器 Item Size Range
9112 4” 50mm ~ 102mm
9113 6” 60mm ~ 152mm
9114 8” 80mm ~ 203mm
9050 / 10054 UNIVERSAL HUB PULLER
三爪式輪軸拔卸器 ● Readily adjustable sliding legs to pull wheel hub more quicker and easier where the bolt circle does not exceed 7-1/2”(190.2mm), also removers press-fit rear brake drums.
● Striking handle and puller screw included.
● Special designed to use on most models of cars.
- CAR REPAIR TOOL - UNDERCAR SERIES
*Prices and specifications are subject to change without prior notice. |21
HKA Tools
9065 / 10063 BRAKE SPRING COMPRESSOR
鼓式剎車彈簧華司拆 ● Big window designed for great visibility during operation.
● Allow fast and easy removal & replacement of brake shoe hold-down springs.
9066 / 10064 BRAKE SPRING TOOL
鼓式剎車來令片彈簧拆裝器 ● Hook the brake return spring and screw up to lock it for removal and installation.
● A smart tool to service those brakes that don’t use anchor pin.
9067 / 10067 HEADLIGHT ADJUSTING AND BRAKE SPRING HOOK
T型剎車彈簧拉鉤 ● This tool made from heat treated-alloy steel is specially designed for removing and installing hard to reach headlight adjusting springs.
9026 / 10065 BRAKE SPRING PLIERS
剎車彈簧鉗(小型) ● Tool easily removes and installs shoe return springs on most drum brakes.
● Socket end removes spring from anchor stud and notched end springs on anchor.
● Tool is chrome plated to resist rust and provide easy clear up.
10066 BRAKE SPRING PLIERS
剎車彈簧鉗(大型) ● For removing and replacing brake springs of drum type brake.
● Claw on jaw is replaceable.
- CAR REPAIR TOOL - UNDERCAR SERIES
22| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
9029 / 10062 UNIVERSAL CALIPER WIND BACK TOOL
剎車分泵調整器組 (全車系) ● Wind back brake piston for replacing brake pad.
● Fit most cars.
9064 / 10010 DISC BRAKE PISTON SEPARATOR
碟式剎車調整器 (前碟) ● For fully floating caliper with single or double piston or for fixed caliper with two pistons.
● This tool allows quick and clean pressing back of caliper pistons into caliper housings without damage to seal or caliper piston.
9094 64MM BRAKE CYLINDER HONE
殺車三爪內徑研磨器(64MM) ● Range: 3/4” - 2-1/2” (19mm - 64mm)
● Stone Size: 28.5 x 5 x 3 (3pcs)
● Collar prevents stone breakage.
● Sleeve makes insertion in cylinder easy and protects stone when not in used.
9118 WH-509 BRAKE FLUID TESTER
WH-509 電子式剎車油檢試器 ● There is an electronic circuit design for the tester to maintain its accuracy in the event of power shortage.
● High tech brake fluid sensor, easy to operate.
● User friendly handle to perfectly fit the hand.
● The tester exam the quality of the brake fluid.
9128 3 FUNCTION TIRE GAUGE
打氣量壓三用錶(夾式大錶頭) ● Air inflator provides user with easy and controlled inflation.
● Cast in alloy body with H-D brass valves.
● With 3-1/2”ft Hose, 3-1/2” Pressure gauge and easy to read.
● 0 to 200psi / 0 to 15 bar, 0 to 15kg/cm2, 0 to 1500kpa.
- CAR REPAIR TOOL - UNDERCAR SERIES
*Prices and specifications are subject to change without prior notice. |23
HKA Tools
9089 / 10069 ROLLER STITCHER
輪胎滾輪工具 ● Durable steel handle.
● Bearing inside for using easier.
9087 / 10068 SNAP IN TYRE VALVE INSTALLER
氣門風嘴拉拔器
● Steel construction tool deep threaded head for positive sealing of all snap in type passenger car tyre valve stems. ● Rubber cover design to protect the rim.
● 3 Position settled.
9151 / 10022 AIR CHUCKS
輪胎打氣頭 ● 230MM.
● 380MM.
9149 / 10021 TIRE PRESSURE GAUGE
棒式輪胎量壓表 ● Calibrated in 0.2 kgs/cm2(20kPa) increments from 1 to 11kg/cm2(100~1100kPa) and 2.5 lb/in2 from 10 tp 160 lb/in2. ● Chrome plated and 270mm long.
● Head I.D. is 8mm.
10083 VALVE CORE REMOVER / INSTALLER TOOL
氣門心起子 ● For installation and removal of standard valve cores.
● Has a screwdriver-style handle.
● Tip diameter: 5.5mm
● Tip length: 60mm
24| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
4031 / 10084 8PC PIN PUNCH SET
平沖組(8PC) ● The cylindrical shank, with ultra-fine tolerances is perfectly smooth.
● To ensure a high degree of toughness.
● Content: 1.6mm, 2.3mm, 3.2mm, 4.0mm, 4.8mm, 5.5mm, 6.4mm, 8.0mm.
4095 / 10114 5PCS TWIST IMPACT SOCKET SET
中長螺旋式防脫套筒 ● Use on the damaged screw and nuts.
● Special spiral design for easier to remove the damaged screw.
● The deep design for easier use on the tire screw.
● Size: 1/2”Dr. 17mm, 19mm, 21mm, 23mm. (Length: 50mm)
4002 / 10023 METRIC FILE RESTORER
八面螺紋銼刀 ● Metric file: 0.75mm, 1.00mm, 1.25mm, 1.50mm, 1.75mm, 2.00mm, 2.50mm & 3.0mm.
● Restore tool for renewing damaged thread on any diameter bolt, stud axle or shaft file both right and left hand threads.
4034 / 10087 15PCS METRIC RETHREADER SET
15PCS 螺紋修護組 ● Content: 7pcs metric rethreader dies.
7pcs metric rethreader taps. 7pcs metric thread file.
● Rethreader dies and tap size: 6 x 1.00, 8 x 1.25, 10 x 1.25, 10 x 1.5, 12 x 1.25, 12 x 1.5, 12 x 1.75.
4035 / 10018 AXLE SPINDLE RETHREADING SET
囉杆修護組 ● Content: 8pcs thread restoring die set used to
clean or repair axle threads on spindle of M24 x 1.50, M24 x 2.00, M22 x 1.00, M22 x 1.50, M20 x 1.5, M20 x 1.25, 13/16” x 20 UNEF, 3/4” x 20 UNEF.
● Used with 1-1/4” socket or wrench.
- CAR REPAIR TOOL - GENERAL SERIES
*Prices and specifications are subject to change without prior notice. |25
HKA Tools
4001 / 10129 FLEXIBLE MAGNETIC PICK UP TOOL
可彎式吸棒 ● Flexible shaft bends and holds in all position.
● Long and slender shaft for easy access to confined areas.
● Comfort-grip handle.
● 20” (510mm) OAL.
4018 / 10130 HEAVY DUTY FLEX MAGNET PICK UP TOL
可彎式吸棒(長型大支) ● Flexible shaft holds shape and can retrieve at hard to reach angles and around obstruction.
● Powerful heavy duty magnet picks up ferrous metal objects to 3-1/2” LBS.
10131 29" JUMBO PRY BAR
特大起子29" ● Go-through alloy steel square.
● Rugged firm grip designed plastic handle.
● Excellent for prying engine, cylinder head, transmission cases, manifold and
drive line components.
4036 / 10085 ROUND MAGNETIC TRAY
圓型磁盤 ● Grabs metal bolts, nuts, screw, nails, washer and other components even
tray is upside down. ● Save your time by having these small parts gathered on tray and you do not
get frustrated when a bolt or nuts rolls out of sight. ● Size: 150mm.
4037 / 10086 RECTANGULAR MAGNETIC TRAY
長方型磁盤 ● Two 3-1/4” heavy duty magnets clamp to ferrous metal surfaces for strong
holding power on the stainless steel tray. ● Holds tools & parts even works upside down.
● Size: 240mm x 140mm.
26| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
4019 / 10135 3PC SCRAPER KNIFE SET
3支組割刀 ● Size: 15mm, 20mm and 30mm.
● Stainless steel, heat treatment of knife.
● High grade wooden grip.
● Sharp tip
4014 MAGNETIC FENDER COVER
葉子板護套 ● Heavy, long wearing foam vinyl. Protect the car.
● With three special magnetic in the cover.
4042 PLASTIC CREEPER
修護臥板 ● One piece construction.
● Easy to clean surface.
● Resistant to solvents, grease and fuels.
● Size: 1000mm x 510mm x 90mm
4043 HEAVY DUTY CREEPERS
鐵架型修護臥板 ● Features 1” steel tube frame for extra strength in heavy duty application.
● Unique drop rail design allows greater shoulder and arm clearance.
● 1” Thick padding on bed; 2” thick padding on headrest.
● Adjustable pneumatic headrest for maximum head comfort and shoulder support.
● Size: 1020 x 430 x 180mm
4010 / 10121 6” ALL STEEL SWIVEL BENCH VISE
白鐵型剪刀 ● Jaws made with the body for economy cost.
● Jaw width: 6”
● Maximum Jaw Opening: 6”
- CAR REPAIR TOOL - GENERAL SERIES
*Prices and specifications are subject to change without prior notice. |27
HKA Tools
4083 TBR-3006 X6 DRAWER TOOL CABINET
TBR-3006 X6六抽工具車(滾珠培令加固定鉤) Measurement (mm) Width Diameter Height
Overall 688 458 735
Overall with caster 688 458 885 Package 770 530 845
2 drawers 591 409 48
2 drawers 591 409 100.5
2 drawers 591 409 153
4082 3 LAYER SERVICE CART
手推三層工具車
28| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
2113 HB210 10 TON COLLISION REPAIR KIT
HB210 10噸油壓板金組 ● Capacity: 10 Ton
● Accessories include:
● 01 Two speed hydraulic hand pump ● 09 Male Connector
● 02 5ft jack hose ● 10Flat base
● 03 4” stroke 10 ton ram ● 11 90° V Base
● 04 1/2 ton hydraulic spreader ram ● 12 Wedge head
● 05 19” Extension tube ● 13 Plunger toe
● 06 14” Extension tube ● 14 Ram toe
● 07 10” Extension tube ● 15 Rubber flex head
● 08 5” Extension tube ● 16 Serrate saddle
2006 / 10126 AP-801 AIR PUMP
氣動幫浦 ● The air power hydraulic pump is designed for using with single acting
cylinders and tools. ● Rugged construction and most components are made of aluminum alloy are built for long service life, easy operation and portability.
● Automatic overload relief setting as 10000 psi protects components in hydraulic system and work safety regardless of air pressure.
● New inlet and outlet design feature low exhausting air volume, non noise effect and being operated in all directions.
2007 / 10123 8P102 EXTRA LONG RAMS
8P102 加長型油壓缸(高級) ● Capacity: 10 Ton
● Stroke: 10”
● Height: 453mm ~ 707mm
● Cylinder bore Dia: φ45
● Oil Port Thread: 1/4”, 3/8”pt
2008 / 10098 8P103 CLAMP ANCHOR BASE
8P103 油壓杆撑頭 ● Use with 5/16” and 3/8” chains.
● Install on the top of model 2007 (8P102)
2009 / 10124 8P104 BALL PIVOT
8P104 油壓杆支轉頭
● Install under the model 2007 (8P102)
● This tool helps operate flexible use model 2007 (8P102)
- CAR REPAIR TOOL – COLLISION REPAIR SERIES
*Prices and specifications are subject to change without prior notice. |29
HKA Tools
2064 / 10125 8P105 4PCS EXTENSION BAR
8P105 4PCS 百金鋼接杆組 ● Length: 5”, 10”, 15”, 20”.
● You could choose different bar to install on the top of model 2007 (8P102)
and this action is for guide the most effective way
2005 5/16” x 9FT CHAIN AND GRAB HOOK
5/16“ x 9FT 吊鍊 ● Size: 5/16”
● Length: 270cm (9ft)
● Level: G80
● With Elbow Hook
2118 / 10099 C101 SMALL MOUTH PULL CLAMP
窄型張引夾 ● Capacity: 5 Ton
● Bolt size: 16m/m φ x 70m/mL
● Single-way pull operation
2002 / 10100 C101N SMALL MOUTH PULL CLAMP (TWO-WAY)
窄型張引夾(雙向) ● Capacity: 5 Ton (Straight way)
2 Ton (Cross way) ● Bolt size: 16m/m φ x 70m/mL
● Two-way pull operation.
2017 / 10101 C102 BIG MOUTH CLAMP
窄型張引夾 ● Capacity: 3 Ton
● Bolt size: 14m/m φ x 120m/mL
● Two-way pull operation.
30| *Prices and specifications are subject to change without prior notice.
PROFESSIONAL TOOL COLLECTION
2003 / 10102 C102N BOX CLAMP
寬型張引夾 ● Capacity: 3 Ton
● Bolt size: 14m/m φ x 110m/mL
● Bolt size’s jaws are different in order to fit the confined room.
● Single -way pull operation.
2018 / 10103 C102NN BOX CLAMP (TWO-WAY)
寬型張引夾(雙向) ● Capacity: 3 Ton (Straight way) 2 Ton (Cross way)
● Bolt size: 14m/m φ x 110m/mL
● Bolt size’s jaws are different in order to fit the confined room.
● Two -way pull operation.
2019 / 10104 C203 HEAVY DUTY CLAMP
重力型張引夾 ● Capacity: 5 Ton
● Bolt size: 20m/m φ x 130m/mL
● Special design for operator when they need to powerfull pulls.
● Single -way pull operation.
10094 EXTRA LARGE SLIDING HAMMER SET
特大型板金滑鎚組 ● For different extent of indentation, it has five
hooks attached. ● The hooks will complete fit kinds of plate to
fix your problem. ● It is a durable and made by steel
10097 LARGE SLIDING HAMMER SET
大型板金滑鎚組 ● Include every kind of hooks and pullers to fit
● Hooks made by plate for easy work when operator use it in confined space
- CAR REPAIR TOOL – COLLISION REPAIR SERIES
*Prices and specifications are subject to change without prior notice. |31
HKA Tools
2059 / 10107 BOUNDED WINDSCREEN REMOVAL TOOL
擋風玻璃防水膠割除器 ● Specially shaped blade is suitable for cutting through bonding resin used to fix modern windscreens.
● The blade can be re-sharpened or replace with a new one.
● Two handle operation permits tool to be accurately guided while cutting
through bond
10108 4PCS PRY BAR SET
四支組起子橇棒 ● Spec.:7/16" x 24"L, 7/16" x 18"L. 3/8" x 12"L, 1/4" x 8"L.
2058 WINDSCREEN REMOVAL TOOL SET
擋風玻璃拆卸綜合組 ● Contents:
* Bounded windscreen removal tool. * Wire * Wire gripping handles * Windshield removal tool * Wire feeder tool * Trim pad removal * Windshield molding release tool.
10105 AUTOMATIC WELDING SLIDE HAMMER
自動點焊倒盾組 ● Full length:435mm
● Connect the positive handle of welding machine into the connector.
● To weld and slide the hammer at the same time.
10106 SLIDE HAMMER HOOK SET
點焊鉤倒盾組 ● Full length:435mm
● To pull out the washer which welding in the indentation
- CAR REPAIR TOOL – COLLISION REPAIR SERIES