Table of contents:- Part List- Set Up Guide

PROFESSIONAL BAR SET UP GUIDE

• Read all the instructions before installing.

• Remove all packing materials before you start.

• This installation requires basic mechanical skills.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the warranty.

• Keep this instruction manual.

BEFORE YOU BEGIN THE INSTALLATIONPAGE 2 OF 9

Note: You may need assistance of one or two persons to set up this bar.

THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUTTHE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED

PROPRIETARY AND CONFIDENTIAL

PROFESSIONAL BAR ASSEMBLY PART LIST PAGE 3 OF 9

Main FrameQTY: 1

Speed RailQTY: 1

Ice BinQTY: 2

Lock PinQTY: 2

Note: Parts are not to scale.

Acrylic PanelQTY: 4

Cutting BoardQTY: 2

CoverQTY: 1

See page 7

PROFESSIONAL BAR ASSEMBLY SET UP STEPS

STEP 1: Remove the counter top.

STEP 2: Release the bottom grill by detaching the security hook.

PAGE 4 OF 9

STEP 3: Pull the side frames. Be careful, they will fall before you fully open them.

THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUTTHE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED

PROPRIETARY AND CONFIDENTIAL

STEP 4: Secure the side frames in place using two locking pins, one on each frame.

Figure 1

Figure 2

Figure 3

Figure 4

P1

P2

P1

PROFESSIONAL BAR ASSEMBLY SET UP STEPS

STEP 5: Flip the shelf up and lock it into place using

the spring latches: and .P3 P4

PAGE 5 OF 9

STEP 6: Flip the table and lock it into place using

the spring latches and .P5 P6

STEP 7: Place the icebins.

THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUTTHE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED

PROPRIETARY AND CONFIDENTIAL

STEP 8: Place the counter top. Then lock it in place

using the spring latches and . Before placing the counter top you can retain both spring latches with the inner frame for ease of placing the counter top.

P7 P8

Figure 5

Figure 6

Figure 7

Figure 8

STEP 9: Place the speed rail.

P3

P4

P5

P6

Figure 9

P7

P8

Note: The positions of the cutting board and the ice bins are interchangeable

PROFESSIONAL BAR ASSEMBLY SET UP STEPSPAGE 6 OF 9

THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUTTHE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED

PROPRIETARY AND CONFIDENTIAL

Figure 10. Full Assembly.

PROFESSIONAL BAR ASSEMBLY SET UP STEPS PAGE 7 OF 9

THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUTTHE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED

PROPRIETARY AND CONFIDENTIAL

How to remove the acrylic panels if needed

Back Panel

STEP 1: Remove screws and . Then remove the tab as shown below.

S1 S2

S1

S2

STEP 2: Pull up the acrylic panel.

Side Panel

STEP 1: Remove screws , , and . Then remove the side frame as in the next step.

S3 S4 S5 S6

STEP 2: Slide out the side panel.

Top Panel

STEP 1: Remove screws and . Then remove the tabs.

S7 S8

S7

S8

S3

S4

S5

S6

STEP 2: Pull the acrylic panel.

PROFESSIONAL BAR COVERSPAGE 8 OF 9

THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUTTHE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED

PROPRIETARY AND CONFIDENTIAL

”4.166

53.85”

14.96”

Contact usTel # 877-958-7901Fax # 866-659-3353E-mail: info@theportablebarcompany.com

Visit us atwww.theportablebarcompany.com

PROFESSIONAL BAR SET UP GUIDE - 03/23/2017