Pro/ENGINEER® Interface for CATIA V5 with Associative...
Transcript of Pro/ENGINEER® Interface for CATIA V5 with Associative...
Pro/ENGINEER® Interface for CATIA V5 with Associative Topology Bus™ (ATB)Pro/ENGINEER Wildfire® Series OverviewAsa TrainerDirector, Product ManagementMarch 2010 Rev I
Forward looking information subject to change without notice © 2009 PTC2
Pro/ENGINEER Interface for CATIA V5 with ATB
Licensed moduleSeparately Licensed Module
–Locked to Pro/ENGINEER (CPT-3232-L)
–Floating Module (PTN-3232-F)
InstallationNo CATIA V5 installation or licensing required
Import and Export processorCATProduct
–Assembly format
CATPart–Part format
CGR –Facet format
Forward looking information subject to change without notice © 2009 PTC3
Interface for CATIA V5Entity Support
Supports 3D geometry and topologyATB-enabled
– Config option topobus_enable yes | no*Visibility support
– Show / No Show– Layers– Hidden
Facet import/export via CGR format– intf3d_in_import_as_facets yes | no | default*
• Default value for CATIA V5 is “no”• Replaces c5_import_as_faceted yes | no (default) in
Pro/ENGINEER Wildfire 4.0 (M030 and later)
–Export transparency and edge color• Pro/ENGINEER Wildfire 4.0 M090 and later
Exact Rep Face Color (optional, by config)– Config option c5_color_import yes | no*
Drawings and applications data (cabling, piping, CAE data) are NOT supported
Forward looking information subject to change without notice © 2009 PTC4
Interface for CATIA V5
CGR ImportImport *.CGR files (parts or assemblies)Import CATPart and/or CATProduct as faceted (extract CGR only)intf3d_import_as_faceted_heal yes (default) | no
5 times faster than exact import!Good for Space Claim and Design-In-Context activities
CGR Export Export Exact data as CGR (faceted)CATPart as CGR, CATProduct with CGR componentsExports mixed part models (exact and facet features) as CATProduct with separate CATPart and CGR components
187 Components
as Exact 20 min
187 Components
as CGR Healed 7 min
187 Components as CGR Quick
4 min
Forward looking information subject to change without notice © 2009 PTC5
Faceted Models for “Design-in-Context”
OperationsMass Properties CalculationMeasurement between Faceted & ExactPairs ClearanceCross Section CreationDatum Feature Creation
FormatsImport STL, VRML, STEP Faceted, CATIA SOLM, DXF 3D & ProductView OL/EDCATIA CGR Design-in-ContextJT
Forward looking information subject to change without notice
New in Pro/ENGINEER Wildfire 5.0
Cables as geometryExport and Import
– Intf3d_out_cables yes | no (default)
– Facet and exact representation
Updated Facet Export ControlsNew in Pro/ENGINEER Wildfire 4.0 M120 and 5.0 M020New Step Size
– Intf3d_out_use_step_size yes | no (default)
– Defines uniform size for triangles
Chord Height and Step Size calculated per part– Intf3d_out_diff_chord_heights yes | no (default)
– Intf3d_out_diff_step_sizes yes | no (default)
– Facet assembly formats only: CATProduct with CGR, JT
© 2009 PTC6
w/o Step Size
with Step Size
Forward looking information subject to change without notice © 2009 PTC7
Interface for CATIA V5Product Structure Support
Support import and export of assemblies containing mixed source components i.e. CATProduct containing
– CATProduct– CATPart– CGR
Additional support for import of assemblies containing mixed source components
– V4 *.model– Must have Interface for CATIA II license
for V4 support
Distributed Pro/BATCH SupportExport and Import TTDs for
–CATPart
–CATProduct
–CGR
Forward looking information subject to change without notice © 2009 PTC8
Associative Topology Bus
AssociativeOne-directional associativity: CATIA V5 to Pro/ENGINEER
Pro/ENGINEER Translated Image Model (TIM)
Contains link to Source (CATIA V5) object
TopologyMaps geometry IDs from CATIA V5 to Pro/ENGINEER
Maintains geometry IDs as changes are made
BusChecks for changes in the CATIA V5 (Source) object
Update import geometry based on changes in Source object
Change Link, Make Independent
Forward looking information subject to change without notice © 2009 PTC9
Support for CATIA Long Names
Long Names (up to 80 characters) supportedSpecial Characters replaced
ATB Mode– in Model Tree
– without Truncation
Non-ATB Mode– Truncated in Model Tree
• With Duplicates Indexed
– Full Names Available
Forward looking information subject to change without notice
New in Pro/ENGINEER Wildfire 4.0 and PDMLink 9.1
Heterogeneous Design-In-Context (HDIC)Multi-CAD (Pro/ENGINEER, UG, CATIA V5) support in Windchill PDMLink
Represent complete mixed CAD product structure in Pro/ENGINEER and Windchill.
One WT Part – one source CAD Document – multiple image CAD Documents
Open CATIA V5 CAD Documents in Pro/ENGINEER to create ATB “image” CAD Documents. CATIA V4 supported in the context of a CATIA V5 assembly.
ATB enables: Check Status, Unlink, Re-link, and associative Updates on Pro/ENGINEER TIM (image) models
Required Components– Pro/ENGINEER Wildfire 4.0 M060 or later
– CATIA V5 R16 (R17 supported in M080 or later)
– Windchill Workgroup Manager for CATIA V5
– PDMLink 9.1 F000 or later© 2009 PTC10
ImageOwner
Part
SourceDerived
TIM
Forward looking information subject to change without notice
duplicate
memory
New in Pro/ENGINEER Wildfire 5.0
Shared MemoryLimited to GPI-based processors
– CATIA V5, CGR, JT, ProductView, UG, Autodesk Inventor, and CADDS5
Introduced in Pro/ENGINEER Wildfire 4.0 (M080)
01020304050
Minutes GB
M070
M080
Shared Memory Performance & Resource
Wildfire 4.0
11
Pro/ENGINEER
IPCsharedmemory
Pro/ENGINEER
GPI Processorduplicate
memoryGPI Processor
Import model (65 MB)1000% 600%Faster less RAM
Benefits– Reduced processing time– Reduced memory (RAM) usage
Before Now
© 2009 PTC
Forward looking information subject to change without notice
New in Pro/ENGINEER Wildfire 5.0
New Import WizardsGreater transparency of data exchange optionsImproved workflowFiner control of settings
Updated import log filesXML format (*.xml)Log Options
– Generate on Import• Short - receipt• Long - full log• None
– Dynamically generate• Info > Data Exchange >
Import Log
Status Indicator
© 2009 PTC12
Forward looking information subject to change without notice
Relevant Config.pro to profile mappings
Config.pro options in Pro/ENGINEER Wildfire 4.0
topobus_enable yes | no*
intf3d_in_import_as_facets yes | no | default*
– And c5_import_as_faceted yes | no*
c5_color_import yes | no*
Profile settings in Pro/ENGINEER Wildfire 5.0
Model tab – Enable ATB
Model tab – Import as facet model
Misc tab – Include Colors
© 2009 PTC13
Forward looking information subject to change without notice
(1) Pro/ENGINEER Wildfire 4.0 Platform Support Matrix
(2) Pro/ENGINEER Wildfire 5.0 Platform Support Matrix
(3) LegendPlatform supported by Pro/ENGINEER and processorPlatform supported by Pro/ENGINEER, but not by processor
– Platform not supported by Pro/ENGINEER
Platform Support
© 2009 PTC14
Pro/ENGINEER Interface for CATIA V5 with ATBPlatforms Pro/ENGINEER
Wildfire 4.0(1)Pro/ENGINEER Wildfire 5.0(2)
OS Processor 32 bit 64 bit 32 bit 64 bitWindows XP Pentium/Xeon
Windows Vista Pentium/Xeon
HP-UX PA8000 – – –SUN Solaris Ultra SPARC II – – –SUN Solaris AMD & Intel – –
Forward looking information subject to change without notice
Interface for CATIA V5 - Version Support
(1) R17 beta support in Pro/ENGINEER Wildfire 4.0. R17 Production support as of Pro/ENGINEER Wildfire 4.0 (M080).(2) R18 beta and R19 beta support as of Pro/ENGINEER Wildfire 4.0 (M080) & 5.0 (F000). R18 and R19 production
support as of Pro/ENGINEER Wildfire 4.0 (M120) & 5.0 (M010).(3) Export format specified via config.pro option introduced in Pro/ENGINEER Wildfire 4.0 (M030).
intf3d_out_catia_v5_version 10* | 12 | 14 | 16 ; (4) As of Wildfire 4.0 (M120) & 5.0 (M010) above arguments become 10 | 14 | 15 | 16* | 17 | 18 | 19 [R19 Public Hidden
until WF5 M020 then Public](5) TPI 144061 details CATIA V5 support in previous releases.
© 2010 PTC15
CATIA V5 Versions SupportPro/ENGINEER Wildfire 4.0 Pro/ENGINEER Wildfire 5.0
CATIA V5 Import Versions R10-R16R17(M080)(1)
[+R18 & R19 (M120)](2)
R10-R17[+R18 & R19 (M020)](2)
CATIA V5 Export Versions R10R14-R16(M030)(3)
[+R17, R18, & R19 (M120)](4)
R10R14-R16(3)
[+R17, R18, & R19 (M020)](4)
For more information contact:Asa TrainerDirector of Product Management, MCAD [email protected]