Products for fixing to Steelwork and Decking Products - SiklaProducts for fixing to Steelwork and...

Products for fixing to Steelwork and Decking

8.0 2019

-10

Products

Beam clamp TCS 0 Beam clamp TCS 1/ TCS 2 Beam clamp TCS 41

Clamping End SKLBulb Flat Steel Beam ClampThreaded Hook GHHook Sleeve SP

Roof Hanger Piercing ToolTRH LOT

Universal Joint UG Beam Clip P U-Holder SB 41

Toggle Stud Hole SawKD LS

Wedge Bolt ClampKB VBO C 40


8.12019

-10

Beam Clamp - Single Support

The safety strap is bent on site to the form of the beam, so that it securely encompasses the edge of the beam flange.

Counter Nut

Basic application Application with Safety Strap

Inverted applicationStanding arrangement

Projecting length of rod not to exceed 10 x rod diameter diameter

Caution!a According to VdS-directive

the use of the Safety Strap is specified for pipes from DN 80 onwards!

Recommendation: Use Safety Strap also, when vibrations are expected.

Caution!a This arrangement is

allowed for parallel-flange beams only

1 2

Caution!a Take note of the torque:

TCS 0: Rotate 1 revolutionTCS 1 and TCS 2: Rotate min. 1 up to max. 1 1/2 revolutions.Then tighten locking nut.


8.2 2019

-10

Universal Joint for any variable Angle Adjustment

Application as a brace

Application on an inclined beam

Braces can be installed with variable angles to their supporting surfaces. The combination with adapters al-lows for bracing arms with cross-sec-tions up to Threaded Tube G1".

Application on an inclinded beamThe pivot head in the Universal Joint can rotate freely, allowing adjustment to any angle.Tightening the locking nut against the adapter plate locks the position.

Caution!a In cases of dynamic loads it is

necessary to secure the Beam Clamp TCS using a Safety Strap, possible in connection with another Beam Clamp TCS.

A B

UGM8 - M16

UG FPM12 and M16

Figure A: Figure B:

Type: Type:UG M8 UG M12UG M10 UG M16

UG FP M12UG FP M16

During installation, make sure the correct side of the adapter plate faces towards the body of the Universal Joint.

Nominal size(NW)

Thread

DN 50 M 8> DN 50 - DN 100 M10> DN 100 - DN 150 M12> DN 150 - DN 200 M16

Note:a The Threaded Rod must be

clearly visible after being screwed into the pivot head.

Note:a Refer to VdS CEA directives

for the recommendation of supporting thread sizes for Sprinkler pipes.


8.32019

-10

Beam Clamp TCS for Header Rails

with Beam ClampTCS 41

perm 160 N/mm²f perm 2 mm

Sample:Beam shape IPB 160 and distance A = 50 cm

Cantilever arrangement with Beam Clamp TCS 1

Channel from size 41/21/2.0 onwards

Beam permissible bending moment

Mb [Nm] IPB 100 50IPB 140 115IPB 160 180IPB 200 310IPB 240 540IPB 300 970IPB 340 1350

Note:a In cantilever arrangements,

the permissible bending moment of the beam must not be exceeded.

= =5 m

a

F

Fperm 180Nm0 5 m,

-------------------- 360N= =

FzulMba

---------=

with Beam Clamp TCS 0; 1; 2

Beam clamps can attach into either the open face or rear slots of the channel, leaving the channel unobstructed for further installations.

Vertical pipe on vertical beam -single support-

Horizontal pipe -twin mounting-Caution!

a T-Head Bolt and Holding Bracket must be used! This arrangement requires Sikla Channel 41/21 or larger. Check permissible loadings by referring to the catalogue!


8.4 2019

-10

Beam Clip for Cross Support/ Dimensioning of Bolts

A B

Bolts used with Beam Clip:

P1: M 8 or M 10P2: M 12P3: M 16P4: M 16

… on thick flangesInstallation within the flange width

When dealing with very thick flanges, use shim plates.Shim plates exceeding 10 mm height must be tack welded to the crossmember!Sliding connection using Slide Set 41

(alternatively, if necessary, rigid connection using Blockset CC 41).

Installation

Determination of the required bolt length Lmin:

Arrangement A Arrangement B (with Hexagon Bolt) (with T-Head Bolt)

P1: Lmin = a + b + 37 [mm] P1: Lmin = b + 40 [mm]P2: Lmin = a + b + 43 [mm] P2: Lmin = b + 45 [mm]P3: Lmin = a + b + 48 [mm] P3: Lmin = b + 50 [mm]P4: Lmin = a + b + 55 [mm] P4: Lmin = b + 60 [mm]


8.52019

-10

Beam Clip for Cross Member Support

Tandem cross support using Channel 41-75/65/3.0 D

Cross member supported by opposing web faces of 2 beams

Installation of a duct -suspended arrangement-

Installation of a duct -directly below the beam-

Note:a When using Beam Clips,

always make sure that - the wider side is located at the Channel and- the smaller side at the beam.


8.6 2019

-10

Beam Clip for Cantilever Support

Double-sided cantilever crossmember

Arrangement with U Bolt

Caution!a The permissible bending

moment of the beam must not be exceeded!

Note:a Use U Bolts only as guides.

If they have to bear some vertical loads, U Bolts type DIN 3570 must be used.

Combination of Support Bracket and Channel with horizontal pipes running parallel to the IPB beam. When using this arrangement, make sure that no axial forces from the pipes exist, which may cause the supporting frame to twist.


8.72019

-10

Beam Clip for Supports on Building Structures

Installation to cast-in channel Installation with anchors

Installation on a timber support Fixing of a timber joist to a steel beam

Fixing two beams crossing each other

Pipe running directly below the beam

Simotec Base Plate GPL can be used between the two beams.


8.8 2019

-10

U-Holder SB 41

For secure support a minimal overhang of 50 mm is necessary.

Arrangement above or below the beam

In all arrangements, the loading capacity of the beam has to be considered. In cantilever arrange-ments especially the torsional stiffness has to be considered

Calculation of loading capacity for horizontal beam with Sikla Structural Analysis Software SiPlan.

Loading capacity per U-Holder SB 41 M10 on horizontal beam up to max. 5kN.

Lateral arrangement on the beam

Due to the geometry of the U-Holder, it is also possible to install Channels MS 41/41 and 41/21 D 90° rotated.

Caution!a In lateral arrangement

secure U-Holders against slipping (e.g. with 2 x TCS).

Type 41 D for profiles as of 41/41 D.

Direct installation of all rectangular single and double channels system 41 on steel beams with flange height up to max. 16 mm.

Note:a U-Holder SB should always

be used in pairs.


8.92019

-10

Threaded Hooks GH for Cross Supports

... hooked onto angle irons ... hooked onto steel C-sections

Flange Nut NT Threaded Hook

Channel MS

Holding Bracket HK

Beam Clip


8.10 2019

-10

Hook Sleves SP and Bulb Flat Steel Beam Clamp for single supports

Hook sleeves may be attached to flanges of C-section or Ibeam steelwork in cases when the beam is rotated through 90°

Installation to Bulb Flat steel (HP-profile)

M10

Combined arrangement as a base plate to a vertical cantilever down post.

The Threaded Hook has a hole Ø13mm and is therefore suitable for Threaded Rods GST M8, M10, M12.If used with a M8 Threaded Rod, a Flange Nut NT is required.

The Bulb Flat Beam Clamp is a solid connection element to fix pipework and electrical containment services to bulb flats HP (80 x 6 up to 160 x 6).

Caution!The load values stated in the catalogue refer only to the Hook Sleeves. The load capa-cities of the supporting beam or building structure must be checked separately.


8.112019

-10

Hook Sleeves and Bulb Flat Beam Clamp for bracket installation

Note:a In cantilever arrangements,

the permissible bending moment of the supporting beam must not be exceeded.

Arrangements to C-section steelwork mounted above or below the beam

Cantilevers to C-section steelwork or angle irons

Suspended header rail to bulb flat steel (HP-profile).


8.12 2019

-10

Clamping End set SKL for Installation to I-beam and C-section profiles between flanges

Cross-member support from webs between two opposing beam faces

Cutting length of the Channel = A - 25 mm

A = clearance between the flanges

Suitable for beams withA = 150 ... 800 mm

To be used in combination with Channels 41/41/2.5 or 41/45/2.5 and Holding Brackets HK 41.

Vertical beam and horizontal pipe run

Pipe run parallel to the beam

Note:a Each Clamping End set SKL

consists of two identical clamping plates. The support Channel between the end plates has to be cut to length on site. Fix the SKL set as deep as possible within the beam profile.

Note:a Bolting torque: min. 1 up to

max. 1 1/2 rotations

Lock after tightening!

A

Caution!a Excess tightening of the point

screws may result in deforma-tion of the beam.


8.132019

-10

Toggle Stud KD for Installation to profiled Metal Decks

1 2

Crossmember mounting

Note:a Based on EN12845:

Pipes > Ø 50 mm must not be attached to trapezoidal steel roof panels.

Hole Saw LS with Centre Drill

Single support

Height adjustment

The Toggle Stud KD is completely pre-assemb-led, making installation safer and faster.

Weatherproof gasket and large washer reliably seals the opening


8.14 2019

-10

Roof Hangers TRH for Installation to Profiled Metal Decking

Type RM

Type MS (with sound absorption) not allowed for sprinkler installations

only 2.5 kg

After piercing, ejector springs ensure a safe return stroke of the hole punches

Adjustable height stopper

Adjustable cut-ting width40 ... 100 mm

Piercing Tool LOT 3

Type M

Roof Hanger TRH RM with knurled nut for height adjustment

Locking nutHexagon Bolt SKT e.g. M8 x 100

Height of perforation does not affect the loading capacity of the Roof Han-ger TRH.

The greater the distance between the perforation and the bottom edge of the profile, the greater the stability of the Metal Decking Sheet.

Note:a Based on EN12845:

Pipes > Ø 50 mm must not be attached to trapezoidal steel roof panels.

Note:a According to the VdS guide-

lines for sprinkler installations, all bolting has to be locked, e.g. with a locking nut at the horizontal bolt.


8.152019

-10

Fixing to Holorib and Cofrastra composite floors

Crossmember mounting

Wedge Bolt KB

Single support

Header Rail InstallationSingle support

Clamp VBO C 40

Products for fixing to Steelwork and Decking Products - SiklaProducts for fixing to Steelwork and...

Documents

Transcript of Products for fixing to Steelwork and Decking Products - SiklaProducts for fixing to Steelwork and...