Productinformation ABB i-bus Uninterruptible Power Supply ...STO/G – page 3 Juni 2009 Overview...
Transcript of Productinformation ABB i-bus Uninterruptible Power Supply ...STO/G – page 3 Juni 2009 Overview...
© STO/G - page 1Juni 2009
ABB i-bus®
Uninterruptible Power Supply Unit NTU/S 12.2000.1
Productinformation
STO/G – page 2Juni 2009
Overview Uninterruptible Power Supply Unit NTU/S 12.2000.1
Universal power supply unit(95…264 V AC)
Buffered voltage of 12 V DC at a max. current of 2 A
Change-over contact(Signals malfunction of the battery, mains power failure and overload/short-circuit)
Integrated overload protection
STO/G – page 3Juni 2009
Overview Uninterruptible Power Supply Unit NTU/S 12.2000.1
Compatible with all standard battery types (SAK 7, SAK 12, SAK 17 and the battery module AM/S 12.1)
Connection of the accumulator overpre-fabricated cable sets(KS/K 4.1 and 2.1)
Electronic battery monitoring
Soft-start function of the battery for starting up the device
STO/G – page 4Juni 2009
Overview Uninterruptible Power Supply Unit NTU/S 12.2000.1
Change-over contact
Mains voltage
LEDs
mains power supply battery supply normal operation near overload malfunction
Battery Start-Up button
12 V output
Battery and PTC connector
STO/G – page 5Juni 2009
Application Uninterruptible Power Supply Unit NTU/S 12.2000.1
Uninterruptible operation of:
12 V DC components of I&HAS* (Motion detectors, technicalsensors, signaling device, …)12 V DC KNX-devices (IP-Router, Zone Terminal, Telephone gateway, …)All other devices using 12 V DCSupplementary power supply forI&HAS*
* Intrusion and hold-up alarm systems
STO/G – page 6Juni 2009
Technical data (Mains voltage) Uninterruptible Power Supply Unit NTU/S 12.2000.1
Mains voltage: 95…264 V AC
Mains frequency: 45…65 Hz
Power consumption: < 55 VA
Leakage loss: < 8 W
STO/G – page 7Juni 2009
Technical data (Storage battery connection) Uninterruptible Power Supply Unit NTU/S 12.2000.1
Charging current:
Storage battery > 5 Ah: 1 A
Storage battery < 5 Ah: 150 mA
STO/G – page 8Juni 2009
Technical data (Output) Uninterruptible Power Supply Unit NTU/S 12.2000.1
Output voltage:13 V +/- 0.5 V SELV
Output current:max. 2 A
STO/G – page 9Juni 2009
Technical data (Change-over contact) Uninterruptible Power Supply Unit NTU/S 12.2000.1
max. switching voltage:
230 V AC od. 5-12 V DC
max. switching current:
1 A at 230 V AC or4-10 mA at 5-12 V DC
STO/G – page 10Juni 2009
Range of application Uninterruptible Power Supply Unit NTU/S 12.2000.1
Uninterruptible Power Supply Unit NTU/S 12.2000.1 Connectable devices
2-fold Zone Terminal MT/U 2.12.1
4-fold Zone Terminal MT/S 4.12.1IP-Router IPR/S 2.1
IP-Interface IPS/S 2.1
Telephone Gateway TG/S 3.2
Universal I/O-Concentrator UK/S 32.2
Technical sensors (gas detector, water detector, …)
Motion detectors
all other devices using 12 V DCDetailed auxiliary equipment on page 14
STO/G – page 11Juni 2009
Discharge curve of storage batteries Uninterruptible Power Supply Unit NTU/S 12.2000.1
STO/G – page 12Juni 2009
Auxiliary equipment Uninterruptible Power Supply Unit NTU/S 12.2000.1
12 V DC lead gel storage batteriesSAK 7 (7 Ah)SAK 12 (12 Ah)SAK 17 (17 Ah)
12 V DC Battery module, MDRCAM/S 12.1 (8 HP)
Cable setsKS/K 4.1 (Basic cable set incl. temperature sensor and microfuse)KS/K 2.1 (Advanced cable set forparallel connection of storage batteriesincl. microfuse)
STO/G – page 13Juni 2009