PRODUCT OVERVIEW: CONVEYOR SYSTEMS · PDF fileScraper Chain Conveyors KKF 400 – 2000 11...
Transcript of PRODUCT OVERVIEW: CONVEYOR SYSTEMS · PDF fileScraper Chain Conveyors KKF 400 – 2000 11...
www.amf-bruns.com
Technical Data
PRODUCT OVERVIEW:CONVEYOR SYSTEMS
PRODUCT OVERVIEW: CONVEYOR SYSTEMS · 3
Contents
Trough Screw Conveyors TSF 100 – 1400 04
Tubular Screw Conveyors RSF 100 – 1400 05
Double Screw Conveyors DSF 100 – 1400 06
Worm Heat Exchangers SWT 250 – 800 07
Vertical Screw Conveyors SRF 250 – 1400 08
Troughed Belt Conveyors MGF 300 – 2000 09
Trough Chain Conveyors TKF 200 – 1000 10
Scraper Chain Conveyors KKF 400 – 2000 11
Scraper Chain Conveyors KKF 400 – 2200 12
Scraper Chain Conveyors KKF 800 – 2200 13
Belt Bucket Elevators GBW 80 – 1250 14
Chain Bucket Elevators KBW 160 – 1000 15
Flat slide valve, electrical FLS 180 – 1040 16
Flat slide valve, pneumatic FLS 180 – 1040 17
Chain conveyor KGB 150 m3 – 600 m3 18
Diverter flap WSK 180 – 1450 19
PRODUCTS BYAMF-BRUNS IN USE
Trough screw conveyor with buckets
Troughed Belt Conveyors
PRODUCT OVERVIEW: CONVEYOR SYSTEMS · 54 · PRODUCT OVERVIEW: CONVEYOR SYSTEMS
Materials:
Trough length:
Gear types:
Drive types:
Trough plate gauge:
Inlet and outlet:
Shaft seals:
Screw diameter:
Auger blade gauge:
Additional options:
S235JR (St37)/1.4301/1.4571
up to 8000 mm manufactured in one piece, without intermediate flange
Spur gears, offset shaft gears and bevel gears
Direct drive, chain drive or coupling drive
2 mm to 10 mm, depending on size
Shape, size and position variable
Stuffing box, Braided seal
100 mm to 1400 mm (or as per client‘s spec)
2 mm to 12 mm, depending on size (or as per client‘s spec)
Protective sleeve/Baffle plate/Cleaning flap/Displacer/Overflow valve/Trough foot/ATEX/
Blocking strips/RPM monitoring/Centre bearing/Custom paint/Special materials/
Hard facing/Wear shells/multiple inlets and outlets/Insulation
Trough Screw Conveyors
TSF 100 to TSF 1400
As the amount being conveyed increases, the conveyor output decreases. Centre bearing only useable up to max. 30% filling ratio.o.r. = on request
Conveying capacity for horizontal use:
Screw diameter Material Class A45 % Filling ratio
Material Class B30 % Filling ratio
Material Class C15 % Filling ratio
[mm] Qm [m3/h] Qm [m3/h] Qm [m3/h]
100 3.5 1 o.r.
125 7 3.5 1.1
160 14 6.5 2.5
200 23 11.5 4
250 42 20 6.5
315 70 35 11
400 120 57 18
500 195 90 29
630 220 140 45
800 260 225 70
1000 360 300 90
1250 o.r. 460 130
1400 o.r. 750 310
Material classes: A: Displacement resistance K=2Material loose and free flowing, non-abrasive (cereals, flour, oil seeds, compound feed, coal dust, plastic dust, plastic granules, etc.)
B: Displacement resistance K=3.5Material not quite free-flowing, slightly abrasive, fine-grained to crushed or mixed (salt, sugar, gypsum, lime, sawdust, etc.)
C: Displacement resistance K=5Material flows poorly, very abrasive, viscous, fibrous or large particles (ash, coke, ore, cement, limestone, soda, etc.)
Technical DataTechnical Data
Materials:
Trough length:
Gear types:
Drive types:
Trough plate gauge:
Inlet and outlet:
Shaft seals:
Screw diameter:
Auger blade gauge:
Additional options:
S235JR (St37)/1.4301/1.4571
up to 8000 mm manufactured in one piece, without intermediate flange
Spur gears, offset shaft gears and bevel gears
Direct drive, chain drive or coupling drive
2 mm to 10 mm, depending on size
Shape, size and position variable
Stuffing box, Braided seal
100 mm to 1400 mm (or as per client‘s spec)
2 mm to 12 mm, depending on size (or as per client‘s spec)
Protective sleeve/Cleaning flap/Trough foot/ATEX/Blocking strips/Custom paint/
Special materials/Hard facing/RPM monitoring/Centre bearing on request/
Wear shells/multiple inlets and outlets
Tubular Screw Conveyors
RSF 100 to RSF 1400
Conveying capacity for horizontal use:
[mm] Qm [m3/h] Qm [m3/h] Qm [m3/h]
100 o.r. o.r. o.r.
125 o.r. o.r. o.r.
160 15 13 10
200 30 25 16
250 55 40 26
315 80 75 44
400 140 120 72
500 250 220 116
630 400 350 180
800 650 570 280
1000 900 800 360
1250 o.r. o.r. o.r.
1400 o.r. o.r. o.r.
Screw diameter Material Class A90 % Filling ratio
Material Class B80 % Filling ratio
Material Class C60 % Filling ratio
Material classes: A: Displacement resistance K=2Material loose and free flowing, non-abrasive (cereals, flour, oil seeds, compound feed, coal dust, plastic
B: Displacement resistance K=3.5Material not quite free-flowing, slightly abrasive, fine-grained to crushed or mixed (salt, sugar, gypsum, lime, sawdust, etc.)
C: Displacement resistance K=5Material flows poorly, very abrasive, viscous, fibrous or large particles (ash, coke, ore, cement, limestone, soda, etc.)
As the amount being conveyed increases, the conveyor output decreases. o.r. = on request
PRODUCT OVERVIEW: CONVEYOR SYSTEMS · 76 · PRODUCT OVERVIEW: CONVEYOR SYSTEMS
Materials:
Trough shape:
Trough length:
Gear types:
Drive types:
Trough plate gauge:
Shaft seals:
Screw diameter:
Auger blade gauge:
Additional options:
S235JR (St37)/1.4301/1.4571/1.4828
Pipe or U-trough
max. 7000 mm up to max. 12000 mm depending on size
Spur gears, offset shaft gears and bevel gears
Direct drive, chain drive or coupling drive
2 mm to 10 mm, depending on size
Stuffing box
250 mm to 800 mm (can be made to client‘s spec)
2 mm to 12 mm, depending on size (or as per client‘s spec)
Protective sleeve/Cleaning flap/Trough foot/ATEX/Custom paint/Special materials/
Hard facing/RPM monitoring/Heat exchange via screw tube, trough, flights possible/
Coolant as per clients‘ request
Worm Heat Exchangers
SWT 250 to SWT 800
Conveying capacity for horizontal use (tube-shaped trough):
[mm] Qm [m3/h] Qm [m3/h] Qm [m3/h]
100 o.r. o.r. o.r.
125 o.r. o.r. o.r.
160 o.r. o.r. o.r.
200 o.r. o.r. o.r.
250 1.3 1.15 0.85
315 3.25 2.8 2.1
400 3.8 3.3 2.5
500 8 7.5 5.1
630 18.8 16.8 12.7
800 23 20.5 15.3
1000 o.r. o.r. o.r.
1250 o.r. o.r. o.r.
1400 o.r. o.r. o.r.
Screw diameter Material Class A90 % Filling ratio
Material Class B80 % Filling ratio
Material Class C60 % Filling ratio
Material classes: A: Displacement resistance K=2Material loose and free flowing, non-abrasive (cereals, flour, oil seeds, compound feed, coal dust, plastic
B: Displacement resistance K=3.5Material not quite free-flowing, slightly abrasive, fine-grained to crushed or mixed (salt, sugar, gypsum, lime, sawdust, etc.)
C: Displacement resistance K=5Material flows poorly, very abrasive, viscous, fibrous or large particles (ash, coke, ore, cement, limestone, soda, etc.)
As the amount being conveyed increases, the conveyor output decreases. o.r. = on request
Technical DataTechnical Data
Materials:
Trough length:
Gear types:
Drive types:
Trough plate gauge:
Inlet and outlet:
Shaft seals:
Screw diameter:
Auger blade gauge:
Additional options:
S235JR (St37)/1.4301/1.4571
up to 8000 mm manufactured in one piece, without intermediate flange
Spur gears, offset shaft gears and bevel gears
Direct drive, chain drive or coupling drive
2 mm to 10 mm, depending on size
Shape, size and position variable
Stuffing box, Braided seal
100 mm to 1400 mm (or as per client‘s spec)
2 mm to 12 mm, depending on size (or as per client‘s spec)
Protective sleeve/Cleaning flap/Trough foot/ATEX/Scraping with 1 drive/Centre bearing/
Displacer/Overflow valve/Blocking strip/RPM monitoring/Custom paint/Special materials/
Hard facing/Wear shells/multiple inlets and outlets/Insulation
Double Screw Conveyors
DSF 100 to DSF 1400
Conveying capacity for horizontal use:
Screw diameter Material Class A45 % Filling ratio
Material Class B30 % Filling ratio
Material Class C15 % Filling ratio
[mm] Qm [m3/h] Qm [m3/h] Qm [m3/h]
100 6.8 1.9 o.r.
125 13.7 6.7 2
160 26.6 12 4.8
200 43.7 22 7.6
250 80 38 12.4
315 133 67 21
400 228 108 34
500 371 171 55
630 570 266 85
800 494 428 133
1000 684 570 171
1250 o.r. 874 247
1400 o.r. o.r. 589
Material classes: A: Displacement resistance K=2Material loose and free flowing, non-abrasive (cereals, flour, oil seeds, compound feed, coal dust, plastic
B: Displacement resistance K=3.5Material not quite free-flowing, slightly abrasive, fine-grained to crushed or mixed (salt, sugar, gypsum, lime, sawdust, etc.)
C: Displacement resistance K=5Material flows poorly, very abrasive, viscous, fibrous or large particles (ash, coke, ore, cement, limestone, soda, etc.)
As the amount being conveyed increases, the conveyor output decreases. Centre bearing only useable up to max. 30% filling ratio.
PRODUCT OVERVIEW: CONVEYOR SYSTEMS · 98 · PRODUCT OVERVIEW: CONVEYOR SYSTEMS
Vertical Screw Conveyors
SRF 250 to SRF 1400
Materials:
Vat:
Power units:
Vat length:
Vat plate thicknesses:
Intake and discharge:
Shaft seal:
Auger diameter:
Auger blade thickness:
Additional options:
S235JR (St37)/1.4301/1.4571
Half shells
Direct drive, coupling (flat, spur, bevel gear units)
2500 mm – 20000 mm (in 200 mm steps)
3 mm to 10 mm, depending on manufactured size
Variable in design, dimensions and position
At bottom stuffing box, at top integrated in compact bearing unit
250 mm to 1400 mm (customer specifications possible)
2 mm to 12 mm, depending on manufactured size (customer specifications possible)
Sleeve at bottom/cleaning flap/blocking strips/ATEX/Special materials/
Custom paint/insulation
Auger diameter (mm): Maximum conveying rate sq.m (m3/h)*
250 20
315 30
400 65
500 100
630 150
800 200
1000 400
1250 650
1400 800
* Dependent on product attributes
Troughed Belt Conveyors
MGF 300 to MGF 2000
Design:
Materials:
Gear types:
Drive types:
Safety components:
Framework joints:
Material guide:
Shaft seals:
Tensioning station:
Drive station:
Belt qualities:
Additional options:
horizontal/rising/concave/convex/reversible/movable
S235JR (St37)/1.4301/vz
Spur gears, offset shaft gears and bevel gears
Direct drive and coupling drive
RPM monitoring/Rope pull emergency stop/Belt misalignment switch/Safety guard
Stable, flanged sheet metal construction/Lower belt safety cover/Plough scraper or
diagonal scraper/Centring station/Guide station/Side rollers
with product guide rails and strip curtains
Braided seal
Spindle tensioning unit/Weight-loaded rear clamping point with carriages/
Weight-loaded central clamping point
Scraper systems/Cleaning Brushes
Approved for foodstuffs/heat and cold resistant/oil & grease resistant/with different
inlays/Steel cord belts
ATEX/Discharge trolley/Belt weighers/Suspended magnet/De-dusting nozzle/
Protective covers (Organit, 1.4301, aluminium, galv.)/Special materials/Custom paint/
Fully enclosed/Level indicator
The capacity can be adjusted by using profiled belts, cross-rib patterns, 5-piece roller garlands, modified troughing angles, higher sidebars and modified unprofiled edges. o.r. = on request
Technical Data
Theoretical capacity in m3/h, , at a belt speed of v = 1 m/sec and 100% filling ratio:
Belt width flat troughed 20°2-piece roller set
troughed 20°3-piece roller set
troughed 30°3-piece roller set
[mm] Qm [m3/h] Qm [m3/h] Qm [m3/h] Qm [m3/h]
300 11.5 22 o.r. o.r.
400 23 46 44 49
500 38 77 72 85
650 69 140 130 153
800 108 220 205 240
1000 173 o.r. 327 386
1200 255 o.r. 478 565
1400 352 o.r. 661 778
1600 464 o.r. 873 1030
1800 592 o.r. 1115 1315
2000 735 o.r. 1380 1635
Correction factors for rising conveyors:
Slope angle: 5° 10° 15° 20° 25° 30°
Correction factor: 0.98 0.95 0.89 0.81 0.68 0.56
Technical Data
PRODUCT OVERVIEW: CONVEYOR SYSTEMS · 1110 · PRODUCT OVERVIEW: CONVEYOR SYSTEMS
Design:
Materials:
Gear types:
Drive types:
Side wall gauges:
Floor plate gauges:
Shaft seals:
Tensioning station:
Drive station:
Chain pitches:
Additional options:
TKF horizontal rising/TKF L-shape/TKF Z-shape
S235JR (St37)/1.4301/1.4571
Spur gears, offset shaft gears and bevel gears
Direct drive, chain drive or coupling drive
3 mm to 6 mm, depending on size
4 mm to 8 mm, depending on size
Braided seal
RPM monitoring/spring tensioning unit
Inspection flaps/Cleaning finger/Level indicator
t=142/t=260
ATEX/with self-propelled retractable tank/Special carrier/Chain breakage monitoring/
Special materials/Custom paint/other chains
Chain Conveyors with single strand chain
TKF 200 to TKF 1000
Horizontal Chain Conveyors: Conveyor output in m3/h (for ƍ =1 t/m3) 100 % filling ratio
Carrier width [mm] 0.1 m/sec 0.2 m/sec 0.3 m/sec 0.4 m/sec 0.5 m/sec
200 15 31 47.5 63 79
250 20 39.5 59 79 99
315 34 68 102 136 170
400 43 86 129.5 173 216
500 72 144 216 288 360
630 90.5 181 272 363 453.5
800 196 391.5 587.5 783.5 979
1000 245 489.5 734 979 1224
Steep-angled Trough Chain Conveyors: Conveyor output in m3/h (for ƍ =1 t/m3) 100 % filling ratio
Carrier width [mm] 0.1 m/sec 0.2 m/sec 0.3 m/sec 0.4 m/sec 0.5 m/sec
200 10.5 21.5 32.5 43 54
250 13.5 27 40.5 54 67.5
315 24 47.5 71.5 95 119
400 30 60.5 90.5 121 151
500 47 93.5 140 187 234
630 59 118 177 236 295
800 129.5 259 389 518 648
1000 162 324 486 648 810
Conveyor output m3/h (theor.) t=142V:The theoretical output is calculated from average trough cross-sections.They are determined in each case by product being conveyed and conveyor output. The real trough cross-section chosen depends on the characteristics of the material being conveyed.
Design:
Materials:
Gear types:
Drive types:
Side wall gauges:
Floor plate gauges:
Shaft seals:
Tensioning station:
Drive station:
Chain pitches:
Additional options:
KKF horizontal/KKF L-shape/KKF Z-shape
S235JR (St 37)/1.4301/1.4571
Spur gears, offset shaft gears, and bevel gears
Direct drive, chain drive, and coupling drive
3 mm to 6 mm, depending on size
4 mm to 8 mm, depending on size
Braided seals
RPM monitoring/spring tensioning unit
Inspection flaps/cleaning fingers/filling level indicator
t=142V/t=260
ATEX/self-propelled retractable tank/special carrier/chain breakage monitor/
special materials/customized paint/other chains
Drag chain conveyor with fork links
KKF 400 to KKF 2000
Conveyor output m3/h (theor.) t=142V:The theoretical output is calculated from the mean trough cross-sections.They depend on the conveyed product and the conveyor output. The actually selected trough cross-section depends on the properties of the conveyed product.
Technical DataTechnical Data
Horizontal drag chain conveyor: Conveyor output in m3/h (for ƍ =1 t/m3) 100 % filling ratio
Carrier width [mm] 0,1 m/sec 0,2 m/sec 0,3 m/sec 0,4 m/sec 0,5 m/sec
400 43 86 129,5 173 216
500 72 144 216 288 360
630 90,5 181 272 363 453,5
800 196 391,5 587,5 783,5 979
1000 245 489,5 734 979 1224
1200 295 590 885 1180 1475
1400 342 685 1028 1371 1714
1600 390 781 1172 1563 1954
1800 438 877 1316 1755 2194
2000 486 973 1460 1947 2434
Steep-angled drag chain conveyor: Conveyor output in m3/h (for ƍ =1 t/m3) 100 % filling ratio
Carrier width [mm] 0,1 m/sec 0,2 m/sec 0,3 m/sec 0,4 m/sec 0,5 m/sec
400 30 60,5 90,5 121 151
500 47 93,5 140 187 234
630 59 118 177 236 295
800 129,5 259 389 518 648
1000 162 324 486 648 810
1200 194 389 583 778 973
1400 226 452 678 904 1131
1600 257 515 773 1031 1289
1800 289 579 868 1158 1448
2000 321 642 963 1284 1606
PRODUCT OVERVIEW: CONVEYOR SYSTEMS · 1312 · PRODUCT OVERVIEW: CONVEYOR SYSTEMS
Horizontal drag chain conveyor: Conveyor output in m3/h (for ƍ =1 t/m3) 100 % filling ratio
Carrier width [mm] 0,1 m/sec 0,2 m/sec 0,3 m/sec 0,4 m/sec 0,5 m/sec
400 86 173 260 347 434
500 107 214 322 429 537
630 135 270 405 540 675
800 169 339 509 679 849
1000 210 421 631 842 1053
1200 251 503 754 1006 1258
1400 292 584 877 1169 1462
1600 333 666 1000 1333 1667
1800 374 748 1122 1496 1871
2000 415 830 1245 1660 2076
2200 458 916 1374 1832 2291
Steep-angled drag chain conveyor: Conveyor output in m3/h (for ƍ =1 t/m3) 100 % filling ratio
Carrier width [mm] 0,1 m/sec 0,2 m/sec 0,3 m/sec 0,4 m/sec 0,5 m/sec
400 57 114 171 228 286
500 70 141 212 283 354
630 89 178 267 356 445
800 112 224 336 448 560
1000 139 278 417 556 695
1200 166 332 498 664 830
1400 193 386 579 772 965
1600 220 440 660 880 1100
1800 246 493 740 987 1234
2000 274 548 822 1096 1370
2200 302 604 907 1209 1512
Design:
Materials:
Gear types:
Drive types:
Side wall gauges:
Floor plate gauges:
Shaft seals:
Tensioning station:
Drive station:
Chain pitches:
Additional options:
KKF horizontal/KKF L-shape/KKF Z-shape
S235JR (St 37)/1.4301/1.4571
Spur gears, offset shaft gears, and bevel gears
Direct drive, chain drive, and coupling drive
3 mm to 6 mm, depending on size
4 mm to 8 mm, depending on size
Braided seals
RPM monitoring/spring tensioning unit
Inspection flaps/cleaning fingers/filling level indicator
t=200 similar to DIN 8168
ATEX/self-propelled retractable tank/special carrier/chain breakage monitor/
special materials/customized paint/other chains
Drag chain conveyor with plate links
KKF 400 to KKF 2200
Conveyor output m3/h (theor.) t=142V:The theoretical output is calculated from the mean trough cross-sections.They depend on the conveyed product and the conveyor output. The actually selected trough cross-section depends on the properties of the conveyed product.
Technical Data
Drag chain conveyor specifically for OSB plants
KKF 800 to KKF 2200with plate link chain
Technical Data
Design:
Side wall materials:
Floor material:
Side wall gauges:
Floor plate gauges:
Top cover:
Gear types:
Drive types:
Shaft seals:
Tensioning station:
Drive station:
Chain pitches:
Additional options:
horizontal/with max. 45° upward angle
S235JR (St 37)
S235JR (St 37) /Hardox/plastic
6 mm and 8 mm
8 mm and 10 mm
3 mm and 4 mm
Spur gears, offset shaft gears, and bevel gears
Direct drive, chain drive, and coupling drive
Braided seals
RPM monitoring/spring tensioning unit
Inspection flap/congestion flap
T= 200 similar to DIN 8165
ATEX/take-up monitor/cleaning pan in the tensioning station
KKF for dry OSB chips: Carrier spacing 800 mm
No. of teeth 9 11 13
Carrier width [mm] Conveyor output [m3/h]
800 432 547 634
1000 540 684 792
1200 648 821 950
1400 756 958 1109
1600 864 1094 1267
1800 972 1231 1426
2000 1080 1368 1584
2200 1188 1505 1742
KKF for wet OSB chips: Carrier spacing 1200 mm
800 575 728 843
1000 718 910 1053
1200 862 1092 1264
1400 1005 1274 1475
1600 1149 1456 1685
1800 1293 1637 1896
2000 1436 1819 2107
2200 1580 2001 2317
Conveyor output with v = 0,5 m/s and 100% filling ratio Max. outputs for drag chain conveyor with plate link chain for OSB plants.
PRODUCT OVERVIEW: CONVEYOR SYSTEMS · 1514 · PRODUCT OVERVIEW: CONVEYOR SYSTEMS
Materials:
Gear types:
Drive types:
Gauge of vertical section steel sheet:
Shaft seals:
Bucket elevator foot:
Bucket elevator head:
Containers:
Additional options:
S235JR (St37)/1.4301/1.4571
Spur gears, offset shaft gears and bevel gears
Direct drive
2 mm (up to 19 m distance between centres) to 5 mm (up to 60 m distance between centres)*
Braided seal
Access doors/Inspection flaps/Movable inlet/Bucket conveyor/RPM monitoring/
Tensioning unit
Inspection flaps/Misalignment monitor/Discharge plate adjustable
DIN 15 231/DIN 15 232/DIN 15 233/DIN 15 234
Drive with spur gear motor and coupling/Platform/ATEX design/Rupture discs/
Exhaustion/Level indicator/Slip monitoring/Special bucket/Special housing/
Bucket conveyor with moving scoop/Gravitational tensioning/Separate backstop/
Large heights on request
Belt Bucket Elevators
GBW 80 to GBW 1250
Materials:
Gear types:
Drive types:
Gauge of vertical section steel sheet:
Shaft seals:
Bucket elevator foot:
Bucket elevator head:
Containers:
Additional options:
S235JR (St37)/1.4301/1.4571
Spur gears, offset shaft gears and bevel gears
Direct drive
2 mm (up to 19 m distance between centres) to 5 mm (up to 60 m distance between centres)*
Braided seal
Access doors/Inspection flaps/Movable inlet/Bucket conveyor/RPM monitoring/
Tensioning unit
Inspection flaps/Discharge plate adjustable
DIN 15 231/DIN 15 232/DIN 15 233/DIN 15 234
Drive with spur gear motor and coupling/Platform/ATEX design/Rupture discs/
Exhaustion/Level indicator/Slip monitoring/Special bucket/Special housing/
Bucket conveyor with moving scoop/Gravitational tensioning/Separate backstop/
Large heights on request
Chain bucket elevators with round link chains
KBW 160 to KBW 1000
Technical DataTechnical Data
Conveyor output m3/h (theor.):The conveyor speed [v] and bucket spacing are assumed averages. They are determined in each case by product being conveyed and conveyor output. The actual bucket filling ratio to be chosen depends on the characteristics of the material being conveyed.
o.r. = on request* Gauge depends on place of installation
** v=1.83 m/s, min. Bucket spacing
Conveyor output m3/h (theor.):The conveyor speed [v] and bucket spacing are assumed averages. They are determined in each case by product being conveyed and conveyor output. The actual bucket filling ratio to be chosen depends on the characteristics of the material being conveyed.
o.r. = on request* Gauge depends on place of installation
** v=1.3 m/s, min. Bucket spacing
Filling ratio Bucket width [mm]
Bucket shape
%80 100 125 160 200 250 315 400 500 630 800 1000 1250
Conveyor output [m3/h] at v = 1.3 m/sec
medium deep
DIN 15 233
100 o.r. o.r. o.r. 11.1 17.5 22 35.1 51 74.1 108 157 292.5 o.r.
90 o.r. o.r. o.r. 10 15.7 19.8 31.6 45.9 66.7 97 141 263.3 o.r.
75 o.r. o.r. o.r. 8.3 13.1 16.5 26.3 38.2 55.5 81 118 219.4 o.r.
deepDIN 15 234
100 o.r. o.r. o.r. 17.5 27.6 35.1 56.1 80.8 117 170 250 454.7 447.1
90 o.r. o.r. o.r. 15.7 24.8 31.6 50.5 72.7 105.3 153 225 409.2 402.4
75 o.r. o.r. o.r. 13.1 20.7 26.3 42 60.6 87.7 127.5 187.5 341 335.3
max 90** o.r. o.r. o.r. 38 55 94 106 152 216 302 426 591 740
Filling ratio Bucket width [mm]
Bucket shape
%160 200 250 315 400 500 630 800 1000
Conveyor output [m3/h] at v = 1.1 m/sec
medium deep
DIN 15 233
100 8 12.8 15.5 24.8 39.5 54.8 76 103 137
90 7.2 11.5 14 22.3 35.5 49.3 68.4 92.7 123.3
75 6 9.6 11.6 18.6 29.6 41 57 77.2 102.7
deepDIN 15 234
100 12.5 19.5 25 40 63 87 120 165 220
90 11.2 17.5 22.5 36 56.6 78.3 108 148.5 198
75 9.4 14.6 18.7 30 47.3 62.5 90 124 165
max 90** 23 36 57 71 92 128 177 242 317
PRODUCT OVERVIEW: CONVEYOR SYSTEMS · 1716 · PRODUCT OVERVIEW: CONVEYOR SYSTEMS
Flat slide valve
FLS EL 180 to FLS EL 1040Electrical with offset shaft gears
Technical Data Technical Data
Materials: Enclosure St37/Slide plate St37/Inlet hopper 1.4301
Enclosure St37/Slide plate 1.4301/Inlet hopper 1.4301
Enclosure 1.4301/Slide plate 1.4301/Inlet hopper 1.4301
Dimensions:
NameSlide valve size
[W]
Thicknessof slide
sheet [b]Thickness
Enclosure [t]Height
[h]Spindle
[S] MotorMax. load onSlide plate
FLS EL 180 180x180 6 4 160 Tr 30x6 LH
„FAZ27DR63L4
P=0.25 kWn=188
with brakeConstruction
type M5“
400 kg
FLS EL 200 200x200 6 4 160 Tr 30x6 LH
FLS EL 220 220x220 6 4 160 Tr 30x6 LH
FLS EL 250 250x250 6 4 160 Tr 30x6 LH
FLS EL 270 270x270 6 4 160 Tr 30x6 LH
FLS EL 300 300x300 6 4 160 Tr 30x6 LH
FLS EL 335 335x335 6 4 160 Tr 30x6 LH
FLS EL 400 400x400 8 4 160 Tr 30x6 LH
FLS EL 425 425x425 8 4 160 Tr 30x6 LH
FLS EL 450 450x450 8 4 160 Tr 30x6 LH
FLS EL 500 500x500 8 5 160 Tr 36x6 LH
FLS EL 525 525x525 8 5 160 Tr 36x6 LH
FLS EL 550 550x550 8 5 160 Tr 36x6 LH
FLS EL 600 600x600 8 5 160 Tr 36x6 LH „FAZ27DRS71M4
P=0.55 kWn=200
with brakeConstruction
type M5“
800 kg
FLS EL 660 660x660 8 5 160 Tr 36x6 LH
FLS EL 800 800x800 8 6 180 Tr 40x7 LH
FLS EL 830 830x830 8 6 180 Tr 40x7 LH
FLS EL 1000 1000x1000 8 6 180 Tr 40x7 LH
FLS EL 1040 1040x1040 8 6 180 Tr 40x7 LH
Note: For slide valves under bunkers, silos, etc., motor output needs to be checked!
Additional options: ATEX - package, equipment for Zone 22
End position switch: 2 proximity sensors Turck Ni12U-EM18-AP6X/3D
Surface finish: DIN EN ISO 12944-5 according to Data Sheet C2 or C3, RAL 1015/5010/6011/7035/9001 satin gloss
Drive options: hand wheel, chain hoist
Flat slide valve
FLS PNE 180 to FLS PNE 1040Flat slide valve, pneumatic
Materials: Enclosure St37/Slide plate St37/Inlet hopper 1.4301
Enclosure St37/Slide plate 1.4301/Inlet hopper 1.4301
Enclosure 1.4301/Slide plate 1.4301/Inlet hopper 1.4301
Dimensions:
Name
Slide valve size[W]
Thicknessof slide
sheet [b]Thickness
Enclosure [t]Height
[h]
Cylinder piston -ø/Stroke
[mm]Max. load onSlide plate
FLS PNE 180 180x180 6 4 160 80/170
300 kg
FLS PNE 200 200x200 6 4 160 80/190
FLS PNE 220 220x220 6 4 160 80/210
FLS PNE 250 250x250 6 4 160 80/240
FLS PNE 270 270x270 6 4 160 80/260
FLS PNE 300 300x300 6 4 160 80/290
FLS PNE 335 335x335 6 4 160 80/320
FLS PNE 350 350x350 6 4 160 80/340
FLS PNE 400 400x400 8 4 160 80/390
FLS PNE 425 425x425 8 4 160 80/410
FLS PNE 450 450x450 8 4 160 80/440
FLS PNE 500 500x500 8 5 160 100/490
700 kg
FLS PNE 525 525x525 8 5 160 100/510
FLS PNE 550 550x550 8 5 160 100/540
FLS PNE 600 600x600 8 5 160 100/590
FLS PNE 660 660x660 8 5 160 100/650
FLS PNE 800 800x800 8 6 180 100/790
FLS PNE 830 830x830 8 6 180 100/820
FLS PNE 1000 1000x1000 8 6 180 125/9901100 kg
FLS PNE 1040 1040x1040 8 6 180 125/1030
Note: For slide valves under bunkers, silos, etc., motor output needs to be checked!
Additional options: ATEX - package, equipment for Zone 22
Position detectors: 2 proximity sensors Turck Ni12U-EM18-AP6X/3D
Surface finish: DIN EN ISO 12944-5 according to Data Sheet C2 or C3, RAL 1015/5010/6011/7035/9001 satin gloss
PRODUCT OVERVIEW: CONVEYOR SYSTEMS · 1918 · PRODUCT OVERVIEW: CONVEYOR SYSTEMS
Technical Data
Diverter flap
WSK 180 to WSK 1450Pneumatic, electric, manual
Versions:
Drive types:
Exit angle:
Side wall gauges:
Standard sizes:
2-way and 3-way version/symmetric and asymmetric
Pneumatic, electric, manual
Standard 30°, others possible
6 mm and 8 mm
180 x 180 up to 1450 x 1450 (adapted to AMF conveyor systems), sizes up to 2000 x 2000
possible without problems
Pneumatic diverter flap
Electric diverter flap
Manual diverter flap
2-way asymmetricdiverter flap
2-way symmetricdiverter flap
3-way symmetricdiverter flap
Stripper rollers above the discharge zone
Distributing chain conveyor Chain conveyor segment
Technical Data
Inside width:
Inside height:
Drive types:
Volume:
Conveyor output:
Miscellaneous:
Additional options:
Features:
3300 mm
useful 3650 mm
Individually powered stripper rollers/separately powered cleaning brush
from 150 m3 up to 600 m3
600 m3 per hour
All bearings are heavy-duty FAG/SKF floating roller type in split pillow blocks/rear wall
designed as a door, so that reverse operation for emergency emptying is possible/precise
batching with frequency-controlled conveyor chain drive/filling level sensors on request
Insulated side walls and roof
· Modular, bolted construction permits any lengths up to 50 m (module length 1950 mm)
· Length can be changed subsequently/simple installation on site
· The entire bunker roof is walkable
· Stripper rollers with side deflectors relieve the seal – the material is always conveyed
towards the middle; a sawtooth blade is not necessary
· Chain conveyor belt with bolted rubber plates permits assembly/disassembly in segments/
repair of individual rubber plates is possible, i.e. there is no need to replace the entire belt
Chain conveyor
KGB 150 m³ up to KGB 600 m³
AMF BRUNS PRODUCTS LEAVE OUR WORKS
IN APEN EVERY DAY FOR DESTINATIONS ALL OVER THE WORLD
PRODUKTÜBERSICHT FÖRDERANLAGEN · 23
AMF-BRUNS SERVICE WORLD
FIRST CLASS – ALSO FOR SERVICE
Reliable and powerful technology is a prerequisite for economic and efficient production. So that you can rely on your plant at any time, we deliver not only first-class technology, but also a tailor-made service portfolio. Be-cause we want you to focus on essentials and be able to exploit the potential of your plant to the full.
This includes professional installation and personal instruction for your staff, but also an efficient mainte-nance and servicing plan. For further questions about our services, we are at your disposal at any time - get in touch with us!
DISCOVER THE AMF-BRUNS SERVICE WORLD!
WE ARE ALWAYS WITHIN EASY REACH
With AMF-Bruns, you are putting your trust in a partner who is always at your side to ensure long-term, safe plant operation. Take advantage of the expertise and experience of our staff. On your behalf, they watch out
for quality, ensure fast order processing and keep your budget in mind at all times. So you always get the best solution from us - safe, sustainable and economical.
FIRST-CLASS SERVICE RIGHT FROM THE START
Our aim is your satisfaction: it starts with planning but does not stop after commissioning. That‘s why we are constantly giving our employees technical training, to be able to provide you with optimum service in any si-tuation. By ensuring professional installation and com-
missioning, our chief erectors, fitters and engineers en-sure optimal settings of your machinery and after that are always available for advice and practical help - for instance in matters of plant optimization and mainte-nance.
SPARE PARTS AND MAINTENANCEBy using AMF-Bruns original parts you are always at the cutting edge of technology. Our special mainte-nance packages also ensure a high level of operational readiness of your plant. AMF Bruns maintains its own stock of spare parts - this way we can guarantee con-
stant availability and speedy delivery, and remedy al-most any technical problem without losing a great deal of time. It goes without saying that you have the full manufacturer‘s warranty on all our replacement parts. We will be pleased to advise you!
SERVICE HOTLINE: + 49 (0) 44 89 - 72 7100
More information is available at www.amf-foerderanlagen.de/service/or send us an e-mail: [email protected]
Reg.–Nr.: Q1 0313014
ZertifiziertesManagement-System
DIN EN ISO 9001
Editi
on 0
4/20
17AMF-Bruns GmbH & Co. KGHauptstraße 101 · 26689 Apen · Germany
www.amf-bruns.com