Product Manual for Wireless Remote - Northern Tool · Unpack your new Plug & Play Wireless Remote...
Transcript of Product Manual for Wireless Remote - Northern Tool · Unpack your new Plug & Play Wireless Remote...
Wireless remote:Plug & Play Wireless remote
(Electric PN: 7076)
unpacking your Wireless remoteUnpack your new Plug & Play Wireless Remote and ensure that all the parts are included by referring to parts list and exploded view drawings provided in this manual.
installation:If your Mile Marker winch features the IP67 waterproof con-nection, then simply plug the receiver box into your solenoid box just as you would your wired remote control. The wire-less receiver has a toggle switch for power, and once “ON” (indicated by a RED light), the unit is ready for use.
For all other models, please follow the instructions at right:
in the box:1. Screws2. Pig Tail (Plug)3. Remote4. Control Box
NOTE: Mile Marker’s Standard Solenoid boxes have 2 screws on each side, as shown in the image above. Remove these screws and lift box cover up.
WARNING: Make sure to unscrew and remove the Power Switch first!
step 1: unscrew and remove the Kill switch
SCEWS
KIllSWITCh
step 2: remove Kill switch first, then remove solenoid Cover
step 3: Wire the Pigtail according to above Diagram and Picture
GREEN
BlACK
BROWN
WhITE
sol 1WEIGHT:
A1
SHEET 1 OF 1SCALE:2:1
DWG NO.
TITLE:
REVISIONDO NOT SCALE DRAWING
MATERIAL:
DATESIGNATURENAME
DEBUR AND BREAK SHARP EDGES
FINISH:UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERSSURFACE FINISH:TOLERANCES: LINEAR: ANGULAR:
Q.A
MFG
APPV'D
CHK'D
DRAWN
IMPORTANT: If your control box has any other pin configuration other than the two below, please contact Mile Marker’s Tech Department at:
(800) 886-8647
GREEN
BlACK
BROWN
WhITE
standard 3 Pin iP67 Waterproof
installation options:There are many options for the placement of your new plug. here are a few options we suggest:(3-1) Slide plug under the Solenoid Box and attach accordingly on the outside of Solenoid.(3-2) Drill the top side of the box cover, on the right side of the Mile Marker logo. Then slide in the head of the pig tail (the plug).(3-3) Drill the right side of the box cover, toward the top. Then slide in the head of the pig tail (the plug).(3-4) This is a sample of what our Standard Solenoid Box looks like after drilling the new hole on the top right of the box.
3-1: remove Power switch first. 3-2: Drill top right of the Box Cover.
3-3: Drill right side of Box Cover. 3-4: sample of solenoid Box With two Plugs.
Warranty information:Mile Marker warrants each Wireless Winch Remote Control, when used in normal service, against factory defects in material and workmanship, to the original purchaser for a period of 1-year. There are no warranties, expressed or implied which extend beyond the original purchaser. The loss of use of the vehicle, loss of time, inconvenience, commercial loss, or consequential damages is not covered.Mile Marker reserves the right to redesign and make any changes to any product without assuming any obligation to modify any product previously manufactured.This warrant gives you specific legal rights. You may also have other rights which vary from state to state. Some states do not allow limitations on how long an implied warranty lasts. Some states do not allow the exclusion or limitation of incidental or consequential damages. Therefore the above limitations or exclusions may not apply to you.All products requiring warranty service must recieve a Returned Goods Authorization Number (RGA) before being sent freight prepaid to Mile Marker. This can be initiated by calling 1-(800) 886-8647.
©Copyright 2012 mile marker, inc.
2121 BlouNt roaDPomPaNo BeaCH, Fl 33069 usa
800.886.8647 toll Free
954.782.0604 usa & iNt’l
954.782.0770 FaX
NOTE: This diagram illustrates proper wiring connection from pigtail to solenoid.