PRODUCT MANUAL - DIAMOND DECOR · DIAMOND DÉCOR® PRODUCT REFERENCE DIAMOND DECOR® 8 DIAMOND...
Transcript of PRODUCT MANUAL - DIAMOND DECOR · DIAMOND DÉCOR® PRODUCT REFERENCE DIAMOND DECOR® 8 DIAMOND...
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E M
Impact resistant mirror with satin etch nish to front face
Colour coated impact resistant glasspanels with satin etch nish to front face
DIAMOND MIRROR ® SATINOVODIAMOND MIRROR ®DIAMOND DÉCOR ® SATINOVODIAMOND DÉCOR ®
Colour coated or screen printed impactresistant glass panels
Impact resistant mirror
DIAMOND SYSTEM PRODUCTS
01
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E M
PROPERTIES
TRANSPORTATION
STRENGTH
AESTHETICS
SAFETY
A lightweight system - one-third lighter than conventional glass. Easy to handle and install.
Signi cantly stronger than ordinary safety glass when installed.Reduced risk of breakage and personal injury.
High clarity re ective image with no distortion.Optical opacity with true colour representation.
Shatterproof: Impact BS 6206 Class A (Diamond 18®) Impact EN 12600 Class B (Diamond 8®)Impact Resistant: Hard Body Impact Human Body Impact Bomb BlastFire Performance: BS 476 Part 6 Class O & Part 7 Class 1.
FEATURES
DIAMOND 8®
DIAMOND 18®
FIXING
TRIMS
Suitable for ‘over cladding’ existing nishes or any smoothcontinous substrate.
Self supporting system, suitable for areas where woodsubstrate is unavailable such as block and brickwork,timber/metal studs.
Adhesive or mechanical xing. No need for drilling whichweakens glass and no unsightly xing heads.
Complementary range of trims providing framed area andmechanical restraint. These are available in a range ofpolished/anodised/coloured nishes.
02
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E M
DIAMOND DÉCOR ® & DIAMOND MIRROR ®
IMPACT RESISTANT?
SHATTERPROOF?
EXPLOSIVE BLAST RESISTANT?
FIRE RATED?
FIXING
WEIGHT
LEAD TIME
ADVANTAGES OVER TOUGHENED GLASS
Yes - Impact resistant to BS 6206 Class A (Diamond 18®)
Impact resistant to EN 12600 Class B (Diamond 8®)
Yes - The 4mm glass breaks safely and cleanly through the full thickness
leaving no splinters or shards.
Yes - Breaks but remains in position after being subjected to measured
explosive blast pressure.
Yes - Surface spread of ame BS476 Part 7 Class 1 / Fire
propagation BS476 Part 6 Index 1 / Combined Class O re rating
Our products can be xed using adhesive bonding only (mechanical restraints
may be recommended subject to application).
11 kg per m² - One third lighter than conventional 6mm safety backed glass.
The lead time for our product is considerably less than toughened glass prod-
ucts. Panels can be cut and manufactured quickly to suit site
requirements as there is no need to go through the time consuming
toughening process.
Our glass products can be cut and supplied to ner tolerances than tough-
ened glass.
No risk of spontaneous explosive failure due to nickel sulphide inclusions.
Replacement panels if required can be supplied quickly.
SAFETY ADVANTAGES
03
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D D É C O R ®
04
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D D É C O R ®
DIAMOND DECOR ® 8PRODUCT REFERENCE DIAMOND DECOR ® 18
FACE MATERIAL
CORE MATERIAL
BACK MATERIAL
NOMINAL THICKNESS
BACKGROUND
EDGE TREATMENT
WEIGHT
MAXIMUM PANEL SIZE
SAFETY
JOINT TREATMENT
FIXING METHOD
ACCESSORIES
PROCESSING OPTIONS
COLOURS
4mm colour coated low iron (crystal clear) or oatglass (slight green tint)
N/A
Impact resistant layer from 4mm expandedpolyether polymer
8mm
Smooth continuous substrate
Polished all round
10kg per m² (nominal)
3000mm x 1200mm
Shatterproof: Impact resistant to BS EN 12600Fire: BS 476 Part 6 & 7 Class 1(see Test Data Summary Sheet)
Arrised butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels, ironmongery etc. Site cutting possible.
Please see Diamond Décor® Colour Guide for options.
4mm colour coated low iron (crystal clear) or oatglass (slight green tint)
Impact resistant layer from 2mm expandedpolyether polymer
12mm (nominal) thick lightweight compositeboard obviating the need for a smooth continuous substrate
18mm
Block & brickwork, timber/metal studs
Polished all round
11kg per m² (nominal)
3000mm x 1150mm
Shatterproof: Impact resistant to BS 6206Fire: BS 476 Part 6 & 7 Class 1(see Test Data Summary Sheet)
Arrised butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels,ironmongery etc. Site cutting possible.
Please see Diamond Décor® Colour Guide for options.
05
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D D É C O R ®
PASTEL ORANGE LILACGREEN BEIGE YELLOW GREEN DUCK EGG
SALMON ORANGE PIGEON BLUELEMON YELLOW NEON GREEN TURQUOISE BLUE
ORANGE BROWN DISTANT BLUETRAFFIC YELLOW LIME GREEN MINT GREEN
TRAFFIC RED
TOMATO RED
OXIDE RED
TANGERINE DAFFODIL YELLOW PURPLEMOSS GREEN PASTEL GREEN PASTEL BLUE
BRIGHTSSTANDARD DIAMOND DÉCOR ® COLOURS
Standard samples available. Bespoke colours available through our colour matching service to RAL, Dulux Trade & Pantone references.Also available in toughened glass solutions and other glass thicknesses. 06
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D D É C O R ®
STANDARD DIAMOND DÉCOR ® COLOURSPASTELS DARKS MONOCHROMES
GENITIAN BLUE ULTRAMARINEWHITE ALUMINIUMAQUA WHITE 9010 ULTRAWHITE
WINE RED TERRA BROWNPEACHBURNT ROSE JET BLACK SLATE
CHOCOLATE COFFEELIGHT IVORYCARAMEL BEIGE BLUE GREY LIGHT GREY
OLIVE GREEN AQUA-FRENCH BLUELIGHT GREENVANILLA DOVE STONE
Standard samples available. Bespoke colours available through our colour matching service to RAL, Dulux Trade & Pantone references.Also available in toughened glass solutions and other glass thicknesses. 07
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D M I R R O R ®
DIAMOND MIRROR ® 8 DIAMOND MIRROR ® 18
FACE MATERIAL
CORE MATERIAL
BACK MATERIAL
NOMINAL THICKNESS
BACKGROUND
EDGE TREATMENT
WEIGHT
MAXIMUM PANEL SIZE
SAFETY
JOINT TREATMENT
FIXING METHOD
ACCESSORIES
PROCESSING OPTIONS
COLOURS
4mm silvered glass (tints available)
N/A
Impact resistant layer from 4mm expandedpolyether polymer
8mm
Smooth continuous substrate
Polished all round
10kg per m² (nominal)
3000mm x 1200mm
Shatterproof: Impact resistant to BS EN 12600Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
Arrised butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels, ironmongery etc. Site cutting possible.
Please see Diamond Mirror® Colour Guide foroptions.
4mm silvered glass (tints available)
Impact resistant layer from 2mm expandedpolyether polymer
12mm (nominal) thick lightweight compositeboard obviating the need for a smooth continuous substrate
18mm
Block & brickwork, timber/metal studs
Polished all round
11kg per m² (nominal)
3000mm x 1150mm
Shatterproof: Impact resistant to BS 6206 Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
Arrised butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels, ironmongery etc. Site cutting possible.
Please see Diamond Mirror® Colour Guide foroptions.
08
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D M I R R O R ®
DIAMOND MIRROR ® 8 DIAMOND MIRROR ® 18
FACE MATERIAL
CORE MATERIAL
BACK MATERIAL
NOMINAL THICKNESS
BACKGROUND
EDGE TREATMENT
WEIGHT
MAXIMUM PANEL SIZE
SAFETY
JOINT TREATMENT
FIXING METHOD
ACCESSORIES
PROCESSING OPTIONS
COLOURS
4mm silvered glass (tints available)
N/A
Impact resistant layer from 4mm expandedpolyether polymer
8mm
Smooth continuous substrate
Polished all round
10kg per m² (nominal)
3000mm x 1200mm
Shatterproof: Impact resistant to BS EN 12600Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
Arrised butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels, ironmongery etc. Site cutting possible.
Please see Diamond Mirror® Colour Guide foroptions.
4mm silvered glass (tints available)
Impact resistant layer from 2mm expandedpolyether polymer
12mm (nominal) thick lightweight compositeboard obviating the need for a smooth continuous substrate
18mm
Block & brickwork, timber/metal studs
Polished all round
11kg per m² (nominal)
3000mm x 1150mm
Shatterproof: Impact resistant to BS 6206 Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
Arrised butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels, ironmongery etc. Site cutting possible.
Please see Diamond Mirror® Colour Guide foroptions.
09
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D M I R R O R ®
Standard samples available. Additional mirror tints may be available subject to quantity and availability.
STANDARD MIRROR COLOURS
ANTIQUE BRONZE
BRONZE TINT
ANTIQUE SILVER
GREY TINTCLEAR SILVER
DIAMOND MIRROR ®
10
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D D É C O R ® S A T I N O V O
DIAMOND DÉCOR 8 ® SATINOVOPRODUCT REFERENCE DIAMOND DÉCOR 18 ® SATINOVO
FACE MATERIAL
CORE MATERIAL
BACK MATERIAL
NOMINAL THICKNESS
BACKGROUND
EDGE TREATMENT
WEIGHT
MAXIMUM PANEL SIZE
SAFETY
JOINT TREATMENT
FIXING METHOD
ACCESSORIES
PROCESSING OPTIONS
COLOURS
4mm colour coated low iron (crystal clear) or
front face
N/A
Impact resistant layer from 4mm expandedpolyether polymer
8mm
Smooth continuous substrate
Polished all round
10kg per m² (nominal)
3000mm x 1200mm
Shatterproof: Impact resistant to BS EN 12600Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
Arissed butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels, ironmongery etc. Site cutting possible.
Please see Diamond Decor® Colour Guide for options.
4mm colour coated low iron (crystal clear) or
front face
Impact resistant layer from 2mm expandedpolyether polymer
12mm (nominal) thick lightweight compositeboard obviating the need for a smoothcontinuous substrate
18mm
Block & brickwork, timber/metal studs
Polished all round
11kg per m² (nominal)
3000mm x 1150mm
Shatterproof: Impact resistant to BS 6206Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
Arissed butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels,ironmongery etc. Site cutting possible.
Please see Diamond Decor® Colour Guide for options.
11
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D D É C O R ® S A T I N O V O
DIAMOND DÉCOR 8 ® SATINOVOPRODUCT REFERENCE DIAMOND DÉCOR 18 ® SATINOVO
FACE MATERIAL
CORE MATERIAL
BACK MATERIAL
NOMINAL THICKNESS
BACKGROUND
EDGE TREATMENT
WEIGHT
MAXIMUM PANEL SIZE
SAFETY
JOINT TREATMENT
FIXING METHOD
ACCESSORIES
PROCESSING OPTIONS
COLOURS
4mm colour coated low iron (crystal clear) or
front face
N/A
Impact resistant layer from 4mm expandedpolyether polymer
8mm
Smooth continuous substrate
Polished all round
10kg per m² (nominal)
3000mm x 1200mm
Shatterproof: Impact resistant to BS EN 12600Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
Arissed butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels, ironmongery etc. Site cutting possible.
Please see Diamond Decor® Colour Guide for options.
4mm colour coated low iron (crystal clear) or
front face
Impact resistant layer from 2mm expandedpolyether polymer
12mm (nominal) thick lightweight compositeboard obviating the need for a smoothcontinuous substrate
18mm
Block & brickwork, timber/metal studs
Polished all round
11kg per m² (nominal)
3000mm x 1150mm
Shatterproof: Impact resistant to BS 6206Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
Arissed butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels,ironmongery etc. Site cutting possible.
Please see Diamond Decor® Colour Guide for options.
12
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D M I R R O R ® S A T I N O V O
DIAMOND MIRROR ® 8 SATINOVO DIAMOND MIRROR ® 18 SATINOVO
FACE MATERIAL
CORE MATERIAL
BACK MATERIAL
NOMINAL THICKNESS
BACKGROUND
EDGE TREATMENT
WEIGHT
MAXIMUM PANEL SIZE
SAFETY
JOINT TREATMENT
FIXING METHOD
ACCESSORIES
PROCESSING OPTIONS
COLOURS
4mm silvered glass (tints available) with satin etch
N/A
Impact resistant layer from 4mm expandedpolyether polymer
8mm
Smooth continuous substrate
Polished all round
10kg per m² (nominal)
3000mm x 1200mm
Shatterproof: Impact resistant to BS EN 12600Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
Arrised butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels,ironmongery etc. Site cutting possible.
Please see Diamond Satinovo Colour Guide foroptions.
4mm silvered glass (tints available) with satin etch
Impact resistant layer from 2mm expandedpolyether polymer
12mm (nominal) thick lightweight compositeboard obviating the need for smooth a continuous substrate
18mm
Block & brickwork, timber/metal studs
Polished all round
11kg per m² (nominal)
3000mm x 1150mm
Shatterproof: Impact resistant to BS 6206Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
Arrised butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels,ironmongery etc. Site cutting possible.
Please see Diamond Satinovo Colour Guide foroptions.
13
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D M I R R O R ® S A T I N O V O
DIAMOND MIRROR ® 8 SATINOVO DIAMOND MIRROR ® 18 SATINOVO
FACE MATERIAL
CORE MATERIAL
BACK MATERIAL
NOMINAL THICKNESS
BACKGROUND
EDGE TREATMENT
WEIGHT
MAXIMUM PANEL SIZE
SAFETY
JOINT TREATMENT
FIXING METHOD
ACCESSORIES
PROCESSING OPTIONS
COLOURS
4mm silvered glass (tints available) with satin etch
N/A
Impact resistant layer from 4mm expandedpolyether polymer
8mm
Smooth continuous substrate
Polished all round
10kg per m² (nominal)
3000mm x 1200mm
Shatterproof: Impact resistant to BS EN 12600Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
Arrised butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels,ironmongery etc. Site cutting possible.
Please see Diamond Satinovo Colour Guide foroptions.
4mm silvered glass (tints available) with satin etch
Impact resistant layer from 2mm expandedpolyether polymer
12mm (nominal) thick lightweight compositeboard obviating the need for smooth a continuous substrate
18mm
Block & brickwork, timber/metal studs
Polished all round
11kg per m² (nominal)
3000mm x 1150mm
Shatterproof: Impact resistant to BS 6206Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
Arrised butt vertical joint, bright polished anodized aluminium ‘H’ section trims to horizontal joints if required - refer to Product Manual or Chelsea Artisans for recommendations.
Adhesive and/or bright polished anodizedaluminium ‘J’ section trims - refer to the Product Manual, Advice Manual or Chelsea Artisans forrecommendations.
Purpose made bright polished anodized aluminium ‘J’ section trims to perimeter and ‘H’ section trims to horizontal joints.
Factory cut outs to accommodate control panels,ironmongery etc. Site cutting possible.
Please see Diamond Satinovo Colour Guide foroptions.
14
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S A T I N O V O
Standard samples available. Bespoke Diamond Décor® Satinovo colours available through our colour matching service to RAL, Dulux Trade & Pantone references.
STANDARD SATINOVO COLOURS
BRONZE
GREYCLEAR SILVER
DIAMOND MIRROR ® SATINOVO
ULTRAWHITE
BLACK
DIAMOND DÉCOR ® SATINOVO
15
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E M
4
122
18
PRODUCT COMPOSIT ION
D I A M O N D D É C O R ® 8 / D I A M O N D M I R R O R ® 8 D I A M O N D D É C O R ® 1 8 / D I A M O N D M I R R O R ® 1 8
THICKNESS
WEIGHT
MAX. PANEL SIZE
SAFETY
8mm (nominal)
10kg per m² (nominal)
3000mm x 1200mm
Shatterproof: Impact resistantto BS EN 12600 Fire: Fire: BS 476 Part 6 & 7 Class 1. Complies with requirements for Class 0. (see Test Data Summary Sheet)
THICKNESS
WEIGHT
MAX. PANEL SIZE
SAFETY
18mm (nominal)
11kg per m² (nominal)
3000mm x 1150mm
Shatterproof: Impact resistant to BS 6206
Fire: BS 476 Part 6 & 7 Class 1.Complies with requirements for Class 0.(see Test Data Summary Sheet)
4 4
8
4mm annealed glasswith colour coating or
mirror nish to rear
Removableprotective lm
Solvent resistantsurface
4mm polyetherpolymer impactresistant layer
4mm annealed glasswith colour coating or
mirror nish to rear
Rot andmoisture-proofaluminium foil
Insulationboard
4mm polyetherpolymer impactresistant layer
16
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E MDIAMOND 8 ® STANDARD ‘ J ’ TR IM
TYPICAL SECTIONRENDERED VISUAL
Diamond Décor® 8/Diamond Mirror® 8
Adhesive
TYPICAL PLAN SECTION
Diamond 8® ‘J’ trim Polished arristo edge of glass
AdhesiveDiamond Décor® 8/Diamond Mirror® 8
Diamond 8® ‘J’ Trim
Packer
NOTE: All trims suppliedwith a bright polished anodized nish as standard. Other nishes available on request subject to availability.
Panel joint
17
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E MDIAMOND 18 ® STANDARD ‘ J ’ TR IM
TYPICAL PLAN SECTION
Diamond 8® ‘J’ trim AdhesiveDiamond Décor® 8/Diamond Mirror® 8
RENDERED VISUAL
Diamond 18® ‘J’ Trim
Diamond Décor® 18/Diamond Mirror® 18
Adhesive
TYPICAL SECTION
Polished arristo edge of glass
PackerPanel joint
NOTE: All trims suppliedwith a bright polished anodized nish as standard. Other nishes available on request subject to availability.
18
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E MDIAMOND 8 ® DIV IDER TRIM DIAMOND 18 ® DIV IDER TRIM
Diamond 8® ‘J’ Trim
Diamond 8® Divider Trim
Diamond Décor® 8/Diamond Mirror® 8
TYPICAL SECTIONTYPICAL SECTION
Diamond 18® Divider Trim
Diamond 18® ‘J’ Trim
Diamond Décor® 18/Diamond Mirror® 18
Adhesive
RENDERED VISUAL RENDERED VISUAL
Adhesive
Packer Packer
NOTE: All trims suppliedwith a bright polished anodized nish as standard. Other nishes available on request subject to availability.
19
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E MDIAMOND 8 ® ANGLE TRIM DIAMOND 18 ® ANGLE TRIM
Diamond 8® ‘J’ Trim
Diamond Décor® 8/Diamond Mirror® 8
Adhesive
Angle Trim
TYPICAL SECTION
Angle Trim
TYPICAL SECTION
Diamond 18® ‘J’ Trim
Diamond Décor® 18/Diamond Mirror® 18
Adhesive
RENDERED VISUAL RENDERED VISUAL
Packer Packer
NOTE 1: All trims suppliedwith a bright polished anodized nish as standard. Other nishes available on request subject to availability.
NOTE 2: Where panelledarea extends above 3mhigh, mechanical restraintwill be necessary.
20
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E M
PLAN SECTION - DIAMOND 8® PLAN SECTION - DIAMOND 8®
PLAN SECTION - DIAMOND 18®
EXTERNAL CORNER JOINT (B IRD ’S BEAK) EXTERNAL CORNER JOINT WITH VERTICAL TRIM
RENDERED VISUAL RENDERED VISUAL21
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
DIAMOND 18 ® INTERNAL CORNER JOINT DIAMOND 8 ® INTERNAL CORNER JOINT
D I A M O N D S Y S T E M
PLAN SECTION PLAN SECTION
RENDERED VISUAL RENDERED VISUAL
22
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E MGLASS SKIRTING TIMBER SKIRTING
Diamond Décor® 18/Diamond Mirror® 18
Skirting by others
Adhesive
Diamond Décor® 18/Diamond Mirror® 18
Diamond Décor® 18/Diamond Mirror® 18
Adhesive
RENDERED VISUAL RENDERED VISUALTYPICAL SECTION TYPICAL SECTION23
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E M
Diamond Décor® 18/Diamond Mirror® 18
Skirting by others
Shaddow gap
Angle trimAngle trim
Skirting by others
Adhesive
Diamond Décor® 18/Diamond Mirror® 18
Adhesive
RENDERED VISUAL RENDERED VISUALTYPICAL SECTION TYPICAL SECTION
TIMBER SKIRTING WITH ANGLE TRIM TIMBER SKIRTING WITH SHADOW GAP
24
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E M
Diamond Décor® 18/Diamond Mirror® 18
Escutcheon plate
Adhesive
Timber rail
Timber rail
Single handrail xingbracket xed back to
background withsuitable xings
Threadedhandrailbracket
TYPICAL SECTION
SINGLE HANDRAIL / BALLET BARRE DOUBLE HANDRAIL / BALLET BARRE
Diamond Décor® 18/Diamond Mirror® 18
Escutcheon plate
Escutcheon plate
Double handrail xingbracket xed back to
background withsuitable xings
Threadedhandrailbracket
TYPICAL SECTION
HANDRAILS - HIDDEN F IX INGS
NOTE: Drilling or cutting glass weakens it and should be avoided. The recommended method for securing handrails is to x a timber rail, or similar, with semi-circular cutouts in the glass. There must be no pressure imposed on the panels at this point. It is necessary to co-ordinate xing positions and panel widths prior to manufacture.
25
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E MSINGLE HANDRAIL / BALLET BARRE DOUBLE HANDRAIL / BALLET BARRE
Diamond Décor® 18/Diamond Mirror® 18
Diamond Décor® 18/Diamond Mirror® 18
TYPICAL SECTION
HANDRAILS - V IS IBLE F IX INGS
Double handrail bracketwith welded xing plate
Diamond Décor® 18/Diamond Mirror® 18
Diamond Décor® 18/Diamond Mirror® 18
Adhesive
Visible timber railxed to background
with suitable xings
Visible timber railxed to background
with suitable xings
Single handrail bracketwith welded xing plate
TYPICAL SECTION
NOTE: Drilling or cutting glass weakens it and should be avoided. The recommended method for securing handrails is to x a timber rail, or similar, with semi-circular cutouts in the glass. There must be no pressure imposed on the panels at this point. It is necessary to co-ordinate xing positions and panel widths prior to manufacture.
26
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E M
DIAMOND 18 ® FRAME TRIMFRAME DETAILS
RENDERED VISUAL - FRONTRENDER
RENDERED VISUAL - REAR TYPICAL SECTION
Diamond 18®
Frame Trim
Diamond Décor® 18/Diamond Mirror® 18
DIAMOND 8 ® FRAME TRIM
TYPICAL SECTION
Diamond 8®
Frame Trim
Diamond Décor® 8/Diamond Mirror® 8
NOTE: All trims suppliedwith a bright polished anodized nish as standard. Other nishes available on request subject to availability.
4mm annealed glasswith colour coating or
mirror nish to rear
Visible xingoption
Framingtrim
Hidden xingoption
27
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
NOTE: All trims supplied with a bright polished anodized nish as standard. Other nishes available on request subject to availability.
D I A M O N D S Y S T E MEXTRUSION PROFILES
DIAMOND 8® ‘J’ TRIM DIAMOND 18® ‘J’ TRIM DIAMOND 8® DIVIDER DIAMOND 8® FRAME
DIAMOND 8® BOTTOM ‘J’ TRIM(subject to availability)
DIAMOND 8® ‘J’ TRIM DIAMOND 18® DIVIDER DIAMOND 18® FRAME
28
+44 (0) 20 8665 0558 [email protected] www.chelsea-fusion.com #Chelsea-Fusion
D I A M O N D S Y S T E M
TEST DATA SUMMARY
DIAMOND 8 ® DIAMOND 18 ®
TEST
EXPLOSION
IMPACTEN12600
SURFACESPREAD OF
FLAME
FIREPROPOGATION
AUTHORITY & DATE
Metropolitan Safety & Protection
1985
Sandberg2013
ExovaWarrington Fire
2013
ExovaWarrington Fire
2013
BS 476 Part 6, (1997) Fire Propaga-tion Index, I = 0.0 in conjunction
with Part 7 Class 1, Part K product rated Class 0.
TEST
IMPACTBS 6206
SURFACESPREAD OF
FLAME
FIREPROPOGATION
AUTHORITY & DATE
Building Investigation& Testing Services
2004
Warrington Fire Research
2001
Warrington Fire Research
2001
NOTES
Class A
BS 476 Part 7, (1997)
BS 476 Part 6, (1997) Fire Propagation Index, I = 0.3 in conjunction with Part 7
Class 1, Part K product rated Class 0.
NOTES
Resisted explosion 4.25m from
face.
Extensive cracking but held
position from 0.23m from face.
Class B – Level of impact
resistance considerably exceeds
the severe duty (SD) rating for
partition wall as de ned in
BS 5234. Glass tested on a
plasterboard skinned metal stud
partition wall background.
Note: Class A can be achieved
with the correct substrate.
BS 476 Part 7, (1997) Class 1.
29