Product Information - SkillsUSA Minnesota...ENVIROBASE® High Performance Waterborne Basecoat...

© 2014 PPG Industries EB-143 12/14

Product Information ENVIROBASE

® High Performance Waterborne Basecoat

Product Description

Envirobase High Performance is a premium waterborne color system for use in repair and repainting of motor

vehicles. Industry leading color capability is easily achieved when applied as part of a two or three-stage basecoat/

clearcoat paint process. Mixed Envirobase High Performance color reproduces the original OEM solid, metallic,

mica, or XIRALLIC® paint finish of virtually all OEM manufacture's worldwide.

Envirobase High Performance products are engineered to reduce volatile organic compounds (VOC) and will

exceed all of today’s legislative VOC restrictions throughout the United States and Canada.

Envirobase High Performance waterborne color system is also capable of producing internal color as well as

interior color. For additional information, see Envirobase product bulletins EB145 for interior color and EB510 for

internal color.

Preparation of Substrate

Apply over original baked finishes or over recommended undercoats.

In all cases, wash all surfaces to be painted with soap and water. Final clean with an appropriate

waterborne cleaner. Ensure that the substrate is thoroughly cleaned and dried before starting

repair.

Apply Envirobase High Performance after sanding with European P800-P1200 / US 500-600

grade paper or dry sand with European P600-800 / US 500-600 grade paper.

Wash off residue and dry thoroughly before recleaning with appropriate waterborne substrate

cleaner. The use of a tack rag is recommended.

• Before mixing, gently hand shake bottles of the Envirobase High Performance toners for a few seconds before

use. Do not place toners or mixed color on shaker or mechanically agitate.

• Mixed Envirobase High Performance color should be thoroughly hand-stirred before application. If not used

immediately it should be hand-stirred again before use.

• Use nylon 125 micron paint filters specially designed for use with waterborne paint materials.

© 2014 PPG Industries EB-143 12/14 2

APPLICATION GUIDE:

Mixing Ratio:

Envirobase High Performance Color 1 Part

T494/T595** 10% by volume for solid color

20% by volume for metallic / pearl color

30% by volume for tinted mid-coat color


T492 Adjuster* 10% by volume for solid color

Envirobase High Performance Metallic / Pearl Color 1 Part

T492 Adjuster* 10% by volume for metallic / pearl color

T494/T595** Thinner +10% by volume for metallic / pearl color

Envirobase High Performance Tinted Mid Coat Color 1 Part

T492 Adjuster* 10% by volume for tinted mid-coat color

T494/T595** Thinner +20% by volume for tinted mid-coat color

*T492 Adjuster has been specifically developed as an enhancement to the Envirobase High Performance basecoat system. Leading edge parts such as bumpers and fascia’s or low profile front ends that may be prone to stone chipping or when driving in extreme conditions

such as abrasive gravel roads or when subjected to high powered pressure washing, the addition of T492 adjuster will improve the

basecoat film properties. Note: Application, flash off and drying is the same as with the standard process. If additional reduction is required for viscosity adjustment, DO NOT add additional T492, use T494/T595 only.

** T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for additional information.

Pot Life

Un-activated, 90 days stored in sealed plastic containers. If activated, pot life is 2 hours.

Hand stir well before using. Do Not mechanically shake.

Additives T581 (optional activator) - 10% by volume after reducing. After activation, additional thinner may be

required to bring the color into the 23-28 second sprayable viscosity range.

Spraygun set up

Fluid Tip: 1.2 - 1.4 mm or equivalent

Spray Viscosity: 23 - 28 seconds, DIN4 @70°F (21°C)

Spray Pressure Color Coat Control Coat

HVLP at the air cap * *

Conventional at the spray gun * *

*Spray gun pressure will vary by manufacturer. See spray gun setup chart DOX440 on ppgrefinish.com

Envirobase / Technical Data Sheets & MSDS Index tab for manufacturer’s pressure information.

Number of Coats All repairs: 2-3 coats to coverage plus control coat*

Horizontal surfaces may require two control coats where vertical surfaces will generaly only require one

control coat.

*Note: A control coat is not required for solid colors.

Flash Off 70°F (21°C)

Between Coats: 1-2 minutes or until dried to a matt finish

Final Flash-off: When application is complete, apply the control coat and allow

it to dry naturally. Force drying of the control coat is not

necessary.

Note: Do not use the spray gun as an air drier. Use air drying equipment.

OR


APPLICATION GUIDE (cont’d):

Drying Times

Dust-Free Each coat approximately 2-4 minutes

70°F (21°C)

Dry to Handle Approximately 15-20 minutes

70°F (21°C)

Dry to De-Nib: Approximately 15-20 minutes

70°F (21°C)

Tape Time 5 minutes

70°F (21°C)

Dry to Clear 15 minutes minimum

70°F (21°C)

Note: Because of the intensity of IR curing, if the clearcoat is to be cured using IR the basecoat will first

need to be cured with IR to remove the residual moisture from the basecoat film.

Overcoat/Recoat

Overcoat with any compatible clear Flash off until the entire surface is touch-dry and has a uniform

matt appearance, or for 15 minutes.*

Dry Sand Use European P1500 / US 800 grit

Recoat After 24 hours, 1 coat of Envirobase High Performance must be

applied prior to the clearcoat application. The maximum recoat

time is 48 hours.

*Temperature, humidity, air movement and film build affect dry times. The best results are achieved with

increased temperature and air movement with minimal film builds.

BLENDING / WET BED

Mixing Ratio:

T490 Tinted Clear Additive 4 Parts

T494 / T595* Thinner 1 Part

For use as a blending additive: Add up to 1 equal par t of the T490 mixture to 1 par t of ready to spray

color and fade into the prepared blend panel.

or

For use as a wet bed: Apply 1 medium light coat of the T490 mixture to the blend panel and or the

entire repair panel and allow to dry. It will be milky blue when wet but will dry translucent. Once dry, apply

color. Be sure that whatever the wet bed material has been applied, it is completely covered with earlier

basecoat or clearcoat.

*T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for additional information.

3 STAGE PEARL PROCESS

Mixing Ratio: Ground Coat Pearl Coat

Color 1 part Color 1 part

T492/T494/T595* Thinner 10%** T292/T494/T595* Thinner 20%**

**Note: Percentage by volume. If using T492 Adjuster, see page 2 for proper use.

* T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for

additional information.


3 STAGE PEARL PROCESS (cont’d):

Viscosity & Pot Life:

Viscosity: 23-28 seconds DIN4 at 70°F (21°C)

Pot Life: 90 days stored in sealed plastic containers.

Always strain before use (nylon 125 micron is recommended).

Spray Gun & Air Pressure

Fluid Tip: 1.2 - 1.4 mm

Color Coat Control Coat

HVLP * *

Compliant * *

*Spray gun pressure will vary by manufacturer. See spray gun set up chart DOX440 on ppgrefinish.com Envirobase High Performance / Technical Data Sheets & MSDS Index tab for manufacturer’s pressure information.

Application: Ground Coat

• Apply single coats until opacity is achieved.

• Flash off thoroughly between coats.

• Avoid heavy application and excessive film

builds.

• Use air movement equipment to accelerate

drying as necessary. Choice of drying methods

will depend upon the type and size or the repair.

• A control coat is not required for solid color

basecoats.

Pearl Coat

• Horizontal and vertical surfaces

• Apply single light coats based on color check

panels. Flash off thoroughly between coats.

• Apply the control coat and allow it to dry

naturally.

• Force drying of the control coat is not necessary.

The pearl color layer is not designed to give

opacity.

Flash Off:

Flash off until uniformly matt in appearance.

Dry Time: Wait until ground coat is uniformly dry before

applying pearl coat

Wait until pearl coat is uniformly dry before applying

clearcoat, approximately 15 minutes.

3 STAGE TINTED MID COAT PROCESS Mixing Ratio: Ground Coat

Color 1 part

T492/T494/T595* Thinner 20% **

Tinted Mid Coat

Color 1 part

T492/T494/T595 Thinner 30%**

** Note: Percentage by volume. If using T492 Adjuster, see page 2 for proper use. * T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for additional information.

Viscosity & Pot Life


Pot Life: 90 days stored in sealed plastic containers

Always strain before use (nylon 125 micron is recommended)


Fluid Tip: 1.2 - 1.4 mm*


HVLP * *

Compliant * *



3 STAGE TINTED MID COAT PROCESS (cont’d):




• Apply the control coat onto dry film for even

metallic appearance.

Tinted Mid Coat


panels.


• The mid coat layer is not designed to give

opacity.

• Flash off the mid coat until it is uniformly dry

before applying clearcoat, approximately 15

minutes.

• A control coat is not required for the tinted

midcoat layer.

Compatibility

Low VOC Markets National Rule Markets

Envirobase High Performance

ECP1x A-Chromatic Surfacer**

ECS2x A-Chromatic LV Sealer

EC530 En.V™ Performance Clearcoat EC700 Series Clearcoats

EC800 Series Clearcoats

EPW115 Waterborne Speed Prime




ECS6x A-Chromatic Sealer EC530 En.V Performance Clearcoat


EC800 Series Clearcoats EPW115 Waterborne Speed Prime

Minor Repair Guidelines

Dirt nibs or other defects in the Envirobase High Performance paint film may be repaired as follows: 1. Allow the surface to completely flash-off.

2. Dry sand the defect with P1500/US 800 grade paper or finer or with a fine abrasive pad or in combination with a small amount of SXA330 Wax and Grease

Remover as a sanding lubricant.

3. Remove sanding dust from the surface by strong air blowing with a clean air supply

4. Tack off surface with SX1070 tack rag.

5. Re-coat the surface with Envirobase High Performance as normal.

ONECHOICE® SXA1031 Aerosol Etch* (cut throughs only)

SXA1050 Plastic Adhesion Primer**

SX1071 Etch Prime**

SX1005 Low VOC wax and Grease Remover

SWX350 H2O-SO-CLEAN™

Plastic Prep System*** (SU4901, SUA4903) SU470LV 1K Compliant Adhesion Promoter

OneChoice

SXA1031 Aerosol Etch* (cut throughs only)


SX1057 Flexible 2K Surfacer SX1060 Rollable 2K Primer Surfacer

Plastic Prep System*** (SU4901, SU4902, SU4903, SUA4903)

SX1005 Low VOC wax and Grease Remover SWX350 H2O-So-Clean

SU470LV 1K Compliant Adhesion Promoter

GLOBAL REFINISH SYSTEM™ D8188

D8126

Global Refinish System

D820*** D8102 D8126

D800x* D8115 D8152

D8099** D8117 D893

D8101 D8150 D894

DELTRON® DPLV305x

DPLV Epoxy

NCP280*

DCU2010

DC3010

DC4010

DC4125

Deltron

DPS305x* DC2000

DVLP Epoxy DC3000

K36 DC4000

DCU2021 DC4125

DCU2042 DX179x***

DCU2060 DPX801***

DCU2082 DPLF*

* For optimum performance a 2K primer or sealer may be used. ** For optimum performance a 2K sealer may be used.

*** Must be primed or sealed.


Envirobase High Performance Waterborne Thinner Selection Guide

Note: Using T595 waterborne thinner with humidity levels above 30% can cause extremely slow flash and overall drying of the basecoat. Do not blend waterborne thinners as this will affect overall basecoat performance. Use either T494 or T595 depending on humidity.

Health and Safety See Material Safety Data Sheet and Labels for additional safety information and handling instructions.

• The contents of this package may have to be blended with other components before the product can be used. Before opening the

packages, be sure you understand the warning messages on the labels and MSDS of all the components, since the mixture will have the hazards of all its parts.

• Improper handling and use, for example, poor spray technique, inadequate engineering controls and/or lack of proper Personal

Protective Equipment (PPE), may result in hazardous conditions or injury.

• Follow spray equipment manufacturer’s instructions to prevent personal injury or fire.

• Provide adequate ventilation for health and fire hazard control.

• Follow company policy, product MSDS and respirator manufacturer’s recommendations for selection and proper sue of respiratory

protection. Be sure employees are adequately trained on the safe use of respirators per company and regulatory requirements.

• Wear appropriate PPE such as eye and skin protection. In the event of injury, see first aid procedures on MSDS.

• Always observe all applicable precautions and follow good safety and hygiene practices.

Equipment Cleaning

• Clean all mixing equipment immediately after use, preferably using a dedicated waterborne equipment cleaning machine with a final

rinse using waterborne thinner. Ensure all equipment is completely dry before storage or use.

• Envirobase High Performance tinters, Envirobase High Performance mixed color & waterborne thinner should be stored in a cool,

dry place away from sources of heat. During storage and transportation, temperature must be maintained at a minimum of 41°F or +5°C or and a maximum of 120°F or 49°C. Avoid exposure to frost or freezing conditions.

• Envirobase High Performance should be mixed in clean, dry plastic containers and equipment. Do not use mixing vessels or spray

equipment that contains solvent residues. Mixing vessels should ideally be plastic - if metal the container should be stainless steel or

have an internal anticorrosion coating.

• Store waterborne & solvent borne wastes separately. A competent agent with appropriate certification must handle all waterborne

wastes. Waste must be disposed of in accordance with all Federal, State, Provincial and local laws and regulations.

• Blended to spray basecoat color with T581 activator has a flash point above 200°F and may be disposed in the waterborne waste

stream intended for basecoat color (without activator). The waste disposal facility should be informed that the waste stream contains

isocyanates. T581 activator handled alone should be disposed in the solvent borne waste stream.

• The Envirobase High performance waterborne paint residues should be segregated from all other wastes and kept in a separate

closed lined container. The Envirobase High Performance waterborne paint residues must be disposed or in accordance with all Federal, State, Provincial and local laws and regulations.

Storage & Handling of Envirobase High Performance


TECHNICAL DATA

Theoretical coverage (RTS), giving 12.7µm (0.5 mils) dry film thickness, 274-640 sq. ft. per US gallon.

Percent solids by volume RTS 8.5 - 20.0%

RTS Combinations Color Color : T494/T595 Color : T494/T595 Color : T494/T595

Applicable Use Category

Color Coating Color Coating Color Coating Color Coating

Ratio

Packaged 1 : 10% 1 : 20% 1 : 30%

Density (g/L) 991-1204 992-1186 992-1171 992-1156

Density (lbs./US gal.) 8.27-10.05 8.28-9.90 8.28-9.77 8.28-9.65

VOC Actual (g/L) 47-120 44-111 43-103 41-97

VOC Actual (lbs./ US gal.) 0.39-1.00 0.37-0.93 0.36-0.86 0.34-0.81

VOC Regulatory (g/L) 207-395 213-401 219-407 225-419

VOC Regulatory (lbs./US gal.) 1.73-3.30 1.78-3.35 1.83-3.40 1.88-3.50

Volatiles wt. %

60.42-84.97 63.42-86.29 66.01-87.44 68.26-88.40

Water wt. %

51.37-74.99 54.94-77.09 58.00-78.85 60.05-80.33

Exempt wt. %

0.0 0.0 0.0 0.0

Water vol. %

61.98-77.47 65.29-79.41 68.03-80.96 70.26-82.22

Exempt vol. %

0.0 0.0 0.0 0.0

RTS Combinations

Color : T494/T595 :

T581

Color : T494/T595 :

T581

Color : T494/T595 :

T581

T490 : T494/T595


Color Coating Color Coating Color Coating

Uniform Finish

Coating

Ratio

1 : 10% : 10% 1 : 20% : 10% 1 : 30% : 10% 4 : 1

Density (g/L) 998-1170 999-1158 998-1146 992

Density (lbs./US gal.) 8.33-9.76 8.34-9.66 8.33-9.56 8.28

VOC Actual (g/L) 70-119 67-112 63-105 91

VOC Actual (lbs./ US gal.) 0.58-0.99 0.56-0.94 0.53-0.88 0.76

VOC Regulatory (g/L) 252-359 256-370 261-373 380

VOC Regulatory (lbs./US gal.) 2.1-3.0 2.14-3.09 2.18-3.11 3.17

Volatiles wt. %

61.4-80.5 64.0-82.0 66.2-83.3 85.7

Water wt. %

51.2-70.0 54.3-72.1 57.0-74.0 76.6

Exempt wt. %

0.0 0.0 0.0 0.0

Water vol. %

60.0-72.1 63.0-74.1 65.5-75.8 76.1

Exempt vol. %

0.0 0.0 0.0 0.0


PPG Automotive Refinish

19699 Progress Drive

Strongsville, OH 44149

800.647.6050

PPG Canada Inc. 2301 Royal Windsor Drive, Unit #6

Mississauga, Ontario L5J 1K5

888.310.4762

Follow us online:

www.ppgrefinish.com

The PPG Logo, Bringing innovation to the surface, Envirobase, OneChoice, Deltron, Global Refinish System, En.V, and H2O-So-Clean are trademarks of PPG Industries Ohio, Inc. Xirallic is a registered trademark of Merck Kgaa.

Emergency Medical or Spill Control Information: (412) 434-4515; In Canada (514) 645-1320

Materials described are designed for application by professional, trained personnel using proper equipment and are not intended for sale to the general public. Products mentioned may be hazardous and should only be used according to directions, while observing precautions and warning systems listed on label. Statements

and methods described are based upon the best information and practices known to PPG Industries. Procedures for applications mentioned are suggestions only and

are not to be construed as representations or warranties as to performance, result, or fitness for any intended use, nor does PPG Industries warrant freedom from patent infringement in the use of any formula or process set forth herein.

RTS Combinations Color : T492 Color : T492 : T494/T595 Color : T492 : T494/T595

Applicable Use Category Color Coating Color Coating Color Coating

Ratio 100 : 10% 100 : 10% : +10% 100 : 10% : +20%

Density (g/L) 995-1056 996-1050 996-1045

Density (lbs./US gal.) 8.30-8.81 8.31-8.76 8.31-8.72

VOC Actual (g/L) 55-102 52-95 48-87

VOC Actual (lbs./ US gal.) 0.46-0.84 0.43-0.79 0.40-0.73

VOC Regulatory (g/L) 216-403 219-405 223-407

VOC Regulatory (lbs./US gal.) 1.80-3.36 1.83-3.38 1.86-3.40

Volatiles wt. % 75.9-86.3 77.9-87.5 79.9-88.7

Water wt. % 70.8-80.1 73.0-81.6 75.2-83.1

Exempt wt. % 0.0 0.0 0.0

Water vol. % 72.1-80.3 74.2-81.7 76.3-83.1

Exempt vol. % 0.0 0.0 0.0

P-178SPLimpiadores solventes

Limpiadores DX Los limpiadores DX de PPG han sido diseñados específicamente para eliminar cera, grasa, siliconas, brea de carreteras, aceite para motor, exceso de pintura, adhesivos y otros contaminantes. Los limpiadores DX han sido empacados listos para usar.

Limpiadores DX

• DX320 - Limpiador de evaporación rápida

• DX330 - Removedor de cera y grasa ACRYLI-CLEAN®

• DX394 - Limpiador con bajo COV 1.4 • DX440 - Removedor de cera y grasa DITZ-O®

Información del producto vigente a partir de 9/13

Limpiadores DX

Instrucciones de uso

Limpiador de evaporación rápida DX320

• El limpiador de evaporación rápida DX320 debe utilizarse como lavado de limpieza final antes de pintar.

• Limpie la superficie con DX330, DX 440 o DX394 como se describe a continuación antes de lijar, encintar, imprimar y sellar.

• Puede utilizar DX320 para remover los contaminantes de la superficie, tal como las huellas dactilares que quedan después de encintar.

• Puede ser utilizado en todos los acabados originales del fabricante, superficies de metal descubierto, y sistemas de acabado curados y secos. No use DX320 sobre plástico o fibra de vidrio.

• Después del encintado final y antes de aplicar el sellador o la pintura, aplique DX320 de manera abundante a la superficie que va a limpiar. Limpie inmediatamente con un paño limpio. No permita que DX320 se seque sobre la superficie. Limpie un área no mayor a 2 pies por 2 pies para evitar el secado prematuro.

DX330 Acryli-Clean DX394 Limpiador con COV bajo 1.4 DX440 Removedor de cera y grasa Ditz-O

• Antes de limpiar, lave la superficie a tratar con agua y jabón.

• Limpie la superficie antes y después de lijar.

• Aplique una cantidad generosa de DX330, DX394 o DX440 con un paño blanco limpio o aplíquelo con una botella rociadora de mano.

• La aplicación inicial hará que los contaminantes floten hacia la superficie, y al limpiar una segunda vez con otro paño limpio y seco se eliminarán estos contaminantes.

• Para obtener resultados óptimos, seque con un paño blanco limpio pasándolo en una sola dirección mientras la superficie todavía está mojada, para eliminar las manchas de contaminantes.

No use DX320, DX330 o DX440 sobre piezas de plástico o fibra de vidrio. La aplicación de estos productos sobre estas superficies puede provocar la acumulación de estática y con ello una combustión súbita.

No utilice DX440 sobre materiales solubles como imprimadores o revestimientos finales con laca.

Datos técnicos: DX320 DX330 DX394 DX440

COV (lb/galón de EE.UU.) 6.31 6.36 1.34 6.94

Importante: Precaución: Utilice protección ocular y de la piel, como guantes resistentes a solventes y gafas de seguridad mientras utiliza productos para la limpieza de superficies. Use con ventilación adecuada. Obedezca todas las precauciones que aparecen en la etiqueta y en la MSDS.

Nota: Los reglamentos locales sobre la calidad del aire pueden limitar el uso de limpiadores DX específicos. Verifique si son adecuados antes de utilizarlos.

Para obtener información adicional sobre seguridad e instrucciones de manipulación, vea las Hojas de Datos de Seguridad del Material (MSDS) y las Etiquetas.

EN CASO DE EMERGENCIAS MÉDICAS O INFORMACIÓN DE CONTROL DE DERRAMES EN LOS EE.UU. LLAME AL 1 (412) 434-4515; EN CANADÁ 1 (514) 645-1320.

Los materiales descritos están diseñados para ser aplicados únicamente por personal profesionalmente capacitado, utilizando el equipo apropiado, y sin la intención de ser vendidos al público en general. Los productos mencionados pueden ser peligrosos y deberán usarse únicamente de acuerdo a las instrucciones, al tiempo que se observan todas las precauciones y advertencias enumeradas en la etiqueta. Las declaraciones y métodos descritos se basan en las mejores prácticas e información conocida a la fecha por PPG Industries. Los procedimientos de aplicación mencionados son sugerencias únicamente y no deben ser considerados como representaciones o garantías del desempeño, resultados o idoneidad de cualquier uso deseado, ni PPG Industries garantiza que no se incurra en incumplimiento de patentes ante el uso de cualquier fórmula o proceso descrito en el presente documento.

Acabado de Automoción PPG

Introduciendo innovaciones en la superficie™

PPG Industries PPG Canada Inc. 19699 Progress Drive 2301 Royal Windsor Drive, Unit #6 Strongsville, OH 44149 Mississauga, Ontario L5J 1K5 1-800-647-6050 1-888-310-4762 Deltron, Acryli-Clean, Ditz-O, el logotipo de PPG y Bringing innovation to the surface son marcas comerciales registradas de PPG Industries of Ohio, Inc.

© 2013 PPG Industries www.ppgrefinish.com Parte No. P-178SP 9/13

Este documento está impreso en

papel reciclado.

P-246SP

DELTRON® Recubrimiento Transparente de Ultra Velocidad

DC2000

Características Superficies compatibles ● Secado rápido al aire ● Base ENVIROBASE® de Alto Rendimiento en Suspensión de Agua ● Lije y pula en 30 minutos o menos

● Base Deltron 2000 (DBC) ● Base GLOBAL REFINISH SYSTEM® BC

● Pinturas de acabado y recubrimientos de acabado originales del fabricante

completamente curados y lijados Ventajas Productos requeridos ● Mayor producción

DC2000 Recubrimiento Transparente de Ultra Velocidad

DCH2015 Endurecedor

DR220 Reductor Acelerado de Temperatura Media (70°- 85 °F/21° - 29 ℃)

DT885 Disolvente de Temperatura Media (75 – 90 °F/24° - 32 °C)

DT895 Disolvente de Alta Temperatura (85 – 95 °F/29° - 35 ℃)

DT898 Disolvente de Temperatura muy Alta (95 °F y superior/35 °C y superior)

D871 Disolvente Medio (65° - 77 °F/18° - 25 °C)

D872 Disolvente Lento (77° - 95 °F/25° - 35 °C)

D873 Disolvente muy Lento (95 °F y superior/35 °C y superior)

● Buen rendimiento en todo tipo de cabinas ● Agiliza el montaje y el tiempo posible de entrega

Beneficios ● Mayor productividad ● Reduce el tiempo de ciclo

DC2000 es un recubrimiento transparente de ultra velocidad y de primera calidad desarrollado específicamente para aumentar la productividad en instalaciones de reparación de colisiones con secado al aire que también reduce los costos de energía en instalaciones que cuentan con cabinas de horneado. El Recubrimiento Transparente de Ultra Velocidad Deltron está diseñado para usar en reparaciones de 1 a 4 paneles. DC2000 ofrece tiempos de secado, pulido y secado al aire extremadamente rápido sin sacrificar la durabilidad ni el aspecto.

Información del producto vigente a partir de 12/13

DC2000

Instrucciones Preparación:

Consulte en el Boletín de Producto específico la información sobre el sistema de colores, para su aplicación, los tiempos de secado y las recomendaciones de mezcla.

Proporciones de mezcla:

DC2000 : DCH2015 : DR220/DT8xx/D8xx 4 partes : 1 parte : .5 - 1 parte

Vida útil:

2 horas a 70 °F (21 ºC)

Aditivos:

DX814

Flexibilizador

DC2000 DCH 2015 DR220/DT8xx/D8xx DX814

4 partes : 1 parte : .5 - 1 parte + 10%

DX73

Eliminador

de gos

Pescado

DC2000 : DCH 2015 DR220/DT8xx/D8xx : DX73

4 partes : 1 parte : .5 - 1 parte +

1 oz. por cuarto de RTS

Para leer las recomendaciones para opacar colores, consulte el boletín OC-2 OneChoice®

Capas de aplicación:

Aplique: 2 capas medianas mojadas sin dejar secar entre una y otra capa

Presión de aire:

HVLP: 0.7 Kg/cm2 (10 psi) en el tapón de aire

De conformidad: 2.03 – 2.81 Kg/cm2 (29 - 40 psi) en la pistola

Convencional: 3.16 – 3.86 Kg/cm2 (45 - 55 psi) en la pistola

Nota: Para obtener los mejores resultados generales, consulte las recomendaciones del fabricante de la pistola respecto a la presión de aire de entrada.

Ajuste de la pistola:

Boquilla: Formación de película por capa húmeda: Formación de película por capa seca:

1.3 - 1.5 mm o equivalente 2 - 3 mils 1 - 1.5 mils

Página 2 P-246SP

Instrucciones Tiempos de secado:

Entre capas: 70 ºF/21 ºC

No es necesario secar por evaporación

Sin polvo: 70 ºF/21 ºC

9 a 12 minutos

Tiempo de cinta: 70 ºF/21 ºC

1 hora

Secado al aire hasta re ensamblar: 70 ºF/21 ºC

1 hora

Secado forzado: 140 ºF/60 ºC

No se recomienda

IR (Infrarrojo)

No se recomienda

Pulido: Secado al aire

70 ºF/21 ºC

25 a 30 minutos

Para reparar o recubrir:

2 a 3 horas de secado al aire a 70 ºF (21 ºC)

DC2000 se debe lijar antes de recubrir con imprimador, color o recubrimiento transparente.

Limpieza del equipo: Las pistolas de rociado, los tapones de las pistolas, los envases de

almacenamiento, etc. se deben limpiar cuidadosamente después de cada uso con cualquier solvente multiuso PPG apropiado.

Página 3 P-246SP

DC2000

Deltron Recubrimiento

Transparente de

Ultra Velocidad Datos técnicos: COV menos solventes exentos (aplicado a 4:1:1) 4.03 - 4.17 lb/gal (483 – 500 g/l) COV menos solventes exentos con DX814

(aplicado a 4:1:1+10%) 4.37 - 4.44 lb/gal (524 – 532 g/l)

COV menos solventes exentos con DX73 (aplicado a 4:1:1+1 oz. por cuarto de RTS) 4.17 - 4.27 lb/gal (500 – 512 g/l)

COV menos solventes exentos con SU4985 (aplicado a X:X:X:X) 5.04 - 5.26 lb/gal (604 – 630 g/l) Sólidos totales por volumen (aplicado a 4:1:1) 35.1%

Rendimiento en pies2/galón de EE.UU. (aplicado a 4:1:1) 564 a 1 mil, 100% de eficiencia de transferencia

Importante: El contenido de este paquete debe ser mezclado con otros componentes antes de utilizarse. Antes de abrir los paquetes, asegúrese de que entiende los mensajes de advertencia en las etiquetas de todos los componentes, ya que la mezcla tendrá los riesgos de todas sus partes. La técnica de rociado inadecuada puede provocar condiciones peligrosas. Siga las instrucciones del fabricante del equipo de rociado para prevenir lesiones personales o incendios. Para usar un respirador, siga las instrucciones. Use protectores de la piel y los ojos. Observe todas las precauciones aplicables.

Para obtener información adicional sobre seguridad e instrucciones de manipulación, vea las Hojas de Datos de Seguridad del Material (MSDS) y las Etiquetas.

EN CASO DE EMERGENCIAS MÉDICAS O INFORMACIÓN DE CONTROL DE DERRAMES EN LOS EE.UU. LLAME AL 1 (412) 434-4515; EN CANADÁ 1 (514) 645-1320.

Los materiales descritos están diseñados para ser aplicados únicamente por personal profesionalmente capacitado, utilizando el equipo apropiado, y sin la intención de ser vendidos al público en general. Los productos mencionados pueden ser peligrosos y deberán usarse únicamente de acuerdo a las instrucciones, al tiempo que se observan todas las precauciones y advertencias enumeradas en la etiqueta. Las declaraciones y métodos descritos se basan en las mejores prácticas e información conocida a la fecha por PPG Industries. Los procedimientos de aplicación mencionados son sugerencias únicamente y no deben ser considerados como representaciones o garantías del desempeño, resultados o idoneidad de cualquier uso deseado, ni PPG Industries garantiza que no se incurra en incumplimiento de patentes ante el uso de cualquier fórmula o proceso descrito en el presente documento.

Acabado de Automoción PPG

Introduciendo innovaciones en la superficie™

PPG Industries 19699 Progress Drive Strongsville, OH 44149 1-800-647-6050

PPG Canada Inc. 2301 Royal Windsor Drive Unit # 6 Mississauga, Ontario L5J 1K5 1-888-310-4762 © 2013 PPG Industries www.ppgrefinish.com Parte N.° P-246SP, 12/13

P-246 DELTRON® Ultra Velocity Clearcoat

DC2000

Features Compatible Surfaces ● Fast air dry ● ENVIROBASE® High Performance Waterborne Basecoat ● Sand and buff in 30 minutes or less

● Deltron 2000 (DBC) Basecoat ● GLOBAL REFINISH SYSTEMl® BC Basecoat

● Fully cured and sanded OEM and refinish paints

Advantages Required Products

● Faster throughput

DC2000 Ultra Velocity Clearcoat

DCH2015 Hardener

DR220 Medium Temperature Accelerated Reducer (70°- 85°F / 21°- 29°C)

DT885 Mid Temperature Thinner (75 - 90°F / 24° - 32°C)

DT895 High Temperature Thinner (85 - 95°F / 29° - 35°C)

DT898 Very High Temperature Thinner (95°F and above / 35°C and above)

D871 Medium Thinner (65° - 77°F /18° - 25°C )

D872 Slow Thinner (77° - 95°F / 25° - 35°C )

D873 Very Slow Thinner (95°F and above / 35°C and above)

● Performs well in all booth types ● Speeds up assembly and delivery time

Benefits

● Increased production ● Reduces cycle times

DC2000 is an ultra velocity, high quality clearcoat, specifically developed to enhance productivity in air-dry collision repair facilities and also reduces energy cost in facilities with baking booths. Deltron

Ultra Velocity Clearcoat is designed for use on repairs of 1- 4 panels. DC2000 offers extremely fast flash, polish and air dry times without sacrificing durability or appearance.

Product Information Effective 12/13

DC2000

Directions For Use

Preparation:

Refer to the specific product Information bulletin of the color system for its application, dry times, and blend recommendations.

Mixing Ratios:

DC2000 : DCH2015 : DR220/DT8xx/D8xx

4 parts : 1 part : ½ to 1 part

Pot Life:

2 hours at 70ºF (21ºC)

Additives:

DX814

Flexibilizer


4 parts : 1 part : ½ to 1 part + 10%

DX73

Fisheye

Eliminator


4 parts : 1 part : ½ to 1 part + 1 oz. to RTS qt.

For flattening recommendations, see OneChoice® bulletin OC-2

Application Coats:

Apply: 2 medium wet coats with no flash between coats Air Pressure:

HVLP: 10 psi at the air cap Compliant: 29 - 40 psi at the gun Conventional: 45 - 55 psi at the gun Note : For best overall results, refer to spraygun manufacturers recommendation for inlet air pressures.

Spray Gun Set-up:

Fluid Tip: Film Build Per Wet Coat Dried Film Build Per Coat:

1.3 - 1.5 mm or equivalent 2 - 3 mils 1 - 1.5 mils

Page 2 P-246

Directions For Use

Drying Times:

Between Coats: 70ºF / 21ºC

No flash required

Dust Free: 70ºF / 21ºC

9-12 minutes

Tape Time: 70ºF / 21ºC

1 hour

Air Dry to Re-assemble: 70ºF / 21ºC

1 hour

Force Dry: 140ºF / 60ºC

Not Recommended

IR

Not Recommended

Polishing: Air Dry

70ºF / 21ºC

25- 30 minutes

Repair and Recoat:

2 - 3 hours air dry 70ºF (21ºC)

DC2000 must be sanded before recoating with primer, color or clear.

Equipment Cleaning: Spray guns, gun cups, storage pots, etc., should be cleaned thoroughly

after each use with any appropriate PPG general purpose solvent.

Page 3 P-246

DC2000

Deltron Ultra

Velocity Clearcoat Technical Data: VOC less exempt solvents (Applied 4:1:1) 4.03 - 4.17 lbs/gal (483 – 500 g/l)

VOC less exempt solvents w/DX814 (Applied 4:1:1+10%) 4.37 - 4.44 lbs/gal (524 – 532 g/l)

VOC less exempt solvents w/DX73 (Applied 4:1:1+1 oz. RTS qt.) 4.17 - 4.27 lbs/gal (500 – 512 g/l) VOC less exempt solvents w/SU4985 (Applied X:X:X:X) 5.04 - 5.26 lbs/gal (604 – 630 g/l)

Total Solids by Volume (Applied 4:1:1) 35.1%

Sq. Ft Coverage / US Gal (Applied 4:1:1) 564 @ 1 mil, 100% transfer efficiency

Important: The contents of this package must be blended with other components before the product can be used. Before opening the packages, be sure you understand the warning messages on the labels of all components, since the mixture will have the hazards of all its parts. Improper spray technique may result in a hazardous condition. Follow spray equipment manufacturer’s instructions to prevent personal injury or fire. Follow directions for respirator use. Wear eye and skin protection. Observe all applicable precautions.

See Material Safety Data Sheet and Labels for additional safety information and handling instructions.

EMERGENCY MEDICAL OR SPILL CONTROL INFORMATION (412) 434-4515; IN CANADA (514) 645-1320

Materials described are designed for application by professional, trained personnel using proper equipment and are not intended for sale to the public. Products mentioned may be hazardous and should only be used according to directions, while observing precautions and warning statements listed on label. Statements and methods described are based upon the best information and practices known to PPG Industries. Procedures for applications mentioned are suggestions only and are not to be construed as representations or warranties as to performance, results, or fitness for any intended use, nor does PPG Industries warrant freedom from patent infringement in the use of any formula or process set forth herein.



PPG Canada Inc. 2301 Royal Windsor Drive Unit #6 Mississauga, Ontario L5J 1K5 1-888-310-4762 The PPG logo, Deltron, Envirobase, Global Refinish System, OneChoice and Bringing innovation to the surface are registered trademarks of

PPG Industries Ohio, Inc. © 2013 PPG Industries www.ppgrefinish.com Part No. P-246, 12/13

North America Technical Data Sheet S2.02.08 Primer/Surfacer

05.13.2010

Autosurfacer Rapid FOR PROFESSIONAL USE ONLY

1/5

Description

Autosurfacer Rapid is a high build, two-component, isocyanate free product that is used as a sanding primer surfacer. Provides fast air drying and baking qualities. Usable under all Sikkens primer sealers and top coats. Autosurfacer Rapid provides excellent application and sanding properties and very good enamel-hold out in combination with all Sikkens topcoats.

100 Autosurfacer Rapid 50 Autosurfacer Rapid Hardener

Use Sikkens Measuring Stick #1 (Black)

Spray gun set-up: Application pressure: Gravity 1.6 –1.8 mm 28 – 30 psi at the air inlet HVLP 1.7–2.0 mm

o Check gun manufacturer specification

2-3 x 1 coat

Between coats

Before curing 3–5 minutes at 70°F (20°C) 1–3 minutes at 70°F (20°C)

70°F (20°C)

140°F (60°C) 45 minutes 20 minutes

Final sanding step; #P500 - #P600 Sikkens topcoats Final sanding step; #P400 when applying Sikkens sealers

Recoatable with all Sikkens topcoats

Use suitable respiratory protection Akzo Nobel Car Refinishes recommends to use fresh air supply respirator.

Read complete TDS for detailed product information


05.13.2010


2/5

Description

Autosurfacer Rapid is a high build, two-component, isocyanate free product that is used as a sanding primer surfacer. Provides fast air drying and baking qualities. Usable under all Sikkens primer sealers and top coats. Autosurfacer Rapid provides excellent application and sanding properties and very good enamel-hold out in combination with all Sikkens topcoats.

Product and additives

Products:

-Autosurfacer Rapid Dark Grey -Autosurfacer Rapid Light Grey

Hardener: Autosurfacer Rapid Hardener

Additive: Autosurfacer Flex: A special additive to improve flexibility when spraying plastic parts.

o In the event of application over raw untreated plastic parts It is advisable to use Primer PO or Plastoflex Primer on any exposed untreated plastic before applying Autosurfacer Rapid.

Basic raw materials

-Autosurfacer Rapid: special acrylic resins -Autosurfacer Rapid Hardener: blocked polyamines of high molecular weight

Suitable substrates

-Existing finishes, degreased and sanded with #P220 to #P320 grit paper dry. -OEM electrocoats (Ecoat), degreased and sanded with #P220 to #P320 grit paper dry or thorough scuff with Scotch-Brite maroon #7447. -Any premium polyester bodyfiller, final sanded with #P180 to #P220 grit dry. -Steel, degreased and sanded with #P80 then #P120 grit dry. -Galvanized, degreased and sanded with #P150 to #P180 grit dry. -Fiberglass gelcoat, degreased and sanded with #P220 to #P320 grit dry. If the gelcoat is broken and has been sanded through, under no circumstance should Autosurfacer Rapid be applied. Recommended is the use of Polysurfacer.

o Although Autosurfacer Rapid will provide adequate adhesion on bare metal, repairs which require extensive metal priming such as whole panel and panels that have had the existing paint system removed, Autosurfacer Rapid should be applied over Washprimer 1K CF or Washprimer EM CF. Allow a 15 minutes flash-off at 70°F (20°C) after Washprimer 1K CF and a 30 minutes flash-off at 70°F (20°C) after Washprimer EM CF application.

Mixing

Autosurfacer Rapid, Light Grey and Dark Grey can be intermixed before proceeding with adding hardener. To make a medium shade of grey; To 100 parts by volume of Light Grey, add 20 parts by volume of Dark Grey. This mixture must further be prepared as follows

Mixing ratio

Mixing Ratio by Volume: 100 parts of Autosurfacer Rapid 50 parts of Autosurfacer Rapid Hardener For easy and accurate mixing, use the Sikkens Measuring Stick #9 (grey).

shearerd

Sticky Note

We will not be using Autosurfacer Flex or Primer PO or Plastoflex Primer during the Skills USA competition

shearerd

Sticky Note

shearerd

Sticky Note


05.13.2010


3/5

Viscosity

20–22 seconds – DIN Cup #4 at 70°F (20°C)

Spray gun set-up / application pressure

Spray gun Fluid tip – set-up Application pressure Gravity HVLP Gravity feed High Transfer Gravity

1.6-1.8 mm 1.7-2.0 mm 1.6-1.8 mm

40–45 psi at the spray gun air inlet HVLP max 10 psi at the air cap. 35 psi at the spray gun air inlet.

o Check gun manufacturer specification

Application process

Spray application; Apply one single coat over any sand through areas. allow this to flash until surface is completely matt. Apply two to three single wet coats; allow a flash off time of 3–5 minutes between coats. Dependant on the required film build.

o Today, many spray gun manufacturers have introduced the small size gravity gun. These spray guns provide the benefit of keeping the overspray contamination to a minimum. For small local repairs consider reducing the gun inlet air pressure to +- 25psi and use a 1.3 to 1.4mm fluid tip.

Rolling application; With a small dense foam roller. Apply one light coat over any sand through areas. Next apply the second and third coat within each preceding coat. Use the edge of the roller to prime awkward areas. Finally, squeeze remaining paint from roller on the pan shelf and smooth off the repair. The rolling should be from the outside in.

o Rolling application will never provide the same film build as spray application. To achieve the best possible film build, allow each coat to flash off well until the surface is completely matt.

Flexible plastic parts

Prior to mixing with Hardener. Add 50 parts by volume of Autosurfacer Flex to Autosurfacer Rapid. Use the first two columns on the #1 (Black) measuring stick; stir this mixture thoroughly before further preparation.

Pot-life

30 minutes at 70°F (20°C) As temperature increases 18°F (10°C) the pot-life decreases 50%

Film thickness

For recommended spray application (3 coats): 6.5-7.5 mils (150-180 µm)


05.13.2010


4/5

Drying times

Drying times relate to recommended application and object temperature

Ready to sand

Distance between short wave IR unit and object. 20 –27 inch (50-70 cm)

70°F (20°C)

45 minutes

The panel must not exceed temperatures above 212°F (100°C)

140°F (60°C)

20 minutes 6 minutes Allow 5 minute flash off prior to infra red curing.

Sanding

Wet: May be presanded with #P600 grit paper wet, final sand with #P800 to #P1000 grit wet. If sanded wet allow 30 minutes at 70°F (20°C) drying time before application of a sealer or top coat Dry: May be presanded with #P320 to #P360 grit dry, moving in stages to final sanding

with #P400 to #P500 grit dry. Sanding in the case of roller application; Pre sand with a sanding block, with a coarser sanding grit; Dry, #P320, in order to remove the coarser surface structure due to the roller application. Sanding should be done from the inside out.

o Normally a wet-on-wet primer sealer is required after sanding, before the top coat is applied.

Recoatable with

After sanding and surface cleaning. Autosurfacer Rapid may be coated itself or with any Sikkens primer sealer or top coat.

o In the case of repriming with itself. Potentially the system laid down is a layer of Washprimer after which two to three coats of Autosurfacer Rapid have been applied and after aggressive sanding, noticed are areas of Washprimer being exposed.

In this case it is advisable to apply heat, such as Infra Red drying for a minimum of 6 minutes. Please see I.R. drying schedule under drying times information, previous page. Before continuing further repriming with Autosurfacer Rapid, or allow overnight drying. Failure to consider this could provide slight wrinkling of the original thin feather edge of Autosurfacer Rapid.

Material usage

With recommended spray application (3 coats), the theoretical material usage is approximately; 18 sq.ft./liter (1.7 m²/liter) ready to spray mixture. The practical material usage depends on many factors i.e. shape of the object, roughness of the surface, application techniques, pressure, method and application circumstances.

Cleaning of equipment

Clean spray equipment with Sikkens Cleaning Solvents or lacquer thinner.

Packaging

–Autosurfacer Rapid: –Autosurfacer Rapid Hardener:

3 Liter can 1 Liter can


05.13.2010


5/5

Color

Light Grey and Dark Grey

VOC

Autosurfacer Rapid (100:50) 4.8 lb/gal (580 g/l) ready to spray mixture.

Safety aspects

Store products unopened between 70°F and 95°F (10°C and 35°C) Avoid too much temperature fluctuation, optimal storage temperature ± 70°C (20°C). Shelf Life: –Autosurfacer Rapid: 2 years if stored unopened –Autosurfacer Rapid Hardener: 1.5 years if stored unopened

Akzo Nobel Car Refinishes Inc. North America Address: 5555 Spalding Drive, Norcross. GA 30092 USA Tel: 770-662-8464 FOR PROFESSIONAL USE ONLY IMPORTANT NOTE The information in this data sheet is not intended to be exhaustive and is based on the present state of our knowledge and on current laws: any person using the product for any purpose other than that specifically recommended in the technical data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. It is always the responsibility of the user to take all necessary steps to fulfill the demands set out in the local rules and legislation. Always read the Material Data Sheet and the Technical Data Sheet for this product if available. All advice we give or any statement made about the product by us (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing otherwise, we do not accept any liability whatsoever for the performance of the product or for any loss or damage arising out of the use of the product. All products supplied and technical advices given are subject to our standard terms and conditions of sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is subject to modification from time to time in the light of experience and our policy of continuous development. It is the user's responsibility to verify that this data sheet is current prior to using the product. Coatings brand names mentioned in this data sheet are trademarks of or are licensed to AkzoNobel. Head Office Akzo Nobel Car Refinishes B.V., PO Box 3 2170 BA Sassenheim, The Netherlands. www.sikkenscr.com

http://www.sikkenscr.com/

Technical Data Sheet Cleaners

December 2014

AutoPrep Ultra Prep Surface Cleaner

FOR PROFESSIONAL USE ONLY

1/2

Description

UltraPrep Surface Cleaner is a waterbased surface cleaner with low VOC content. UltraPrep Surface Cleaner is used to ensure removal of all kinds of contamination from the substrate prior to paint application.

Suitable Substrates

Steel

Stainless Steel Zinc Coated Steel Aluminum Existing Finishes Plastic Substrate

Cleaning technique

After washing the car or the surface of the body panel under treatment, wet a clean cloth with the

UltraPrep Surface Cleaner and clean the surface under treatment. Immediately thereafter, wipe the surface thoroughly dry with high quality absorbent surface cleaning cloths. Always use two cloths, as one cloth will merely shift rather than remove dirt and grease. Do not allow the surface cleaner to evaporate on substrate or the contamination on the surface will remain. Wipe the substrate thoroughly dry before the surface cleaner evaporates. The purpose of surface cleaning is to remove residual grease, oil, wax, silicones, sand, etc. If this is not done, residual contaminant will remain in scratch marks during sanding. Adhesion of the paint system subsequently applied to the contaminated surface will be poor and could delaminate.

o Replace cloths being used for cleaning regularly by clean ones. Instead of placing used (wet) rags in a sealed container place them on the floor grating so that the solvents can evaporate, then place the dried cloths in the regular dustbin.

Point of attention on surface cleaning:

Salt residue and blistering:

With all cleaning activities: once the surface under treatment has been cleaned, it must never be touched with the bare hand; as salts, moisture and oils can be transferred to the prepared surface which may result in delamination or blistering problems. It is particularly important that hand protecting barrier creams are never used near an automobile that is to be refinished. Should you still have touched a sanded and cleaned surface with bare hands; clean it again with first one of the solvent borne and next with one of the water borne cleaners again according the recommended cleaning technique. Truck body constructions:

It is important to prevent dirt residues from getting into construction joints of vans, lorries, etc. during cleaning . They might cause adhesion problems when the paint is applied. Vertically fitted parts should, therefore, first be the surface should be cleaned from the bottom upwards and subsequently from the top downwards.


December 2014



2/2

Point of attention on surface cleaning continued):

Cleaning and condensation on metal surfaces:

After a surface has been cleaned, solvent will evaporate. Heat needed for evaporation is withdrawn from that surface, making it colder than the surrounding atmosphere, which results in (often not visible) condensation on the surface. Allow the moisture sufficient time to evaporate. The first coat of paint can be applied as soon as the surface has re-gained the temperature of the surrounding atmosphere. Earlier application of the coat may lead to adhesion problems. The same problem may arise if a vehicle is transferred from a cold room to a warm one or from outdoors to indoors. Allow vehicles a minimum of one hour to acclimatize. Double-walled vehicles (and certainly insulated ones) require some hours to acclimatize.

Health and Safety

Akzo Nobel Car Refinishes recommends providing adequate ventilation during surface cleaning with any of the mentioned cleaners. Where reasonably practicable, this should be achieved by the use of local exhaust ventilation and good general extraction. If these are not sufficient to maintain concentrations of particulates and solvent vapours below the OEL, suitable respiratory protection must be worn. Besides respiratory protection, always wear solvent resistant gloves while surface cleaning even though working with a low solvent degreaser. This will reduce the risk of cleaning solvents being absorbed into the skin and prevent salts and oils on your hands from contaminating the surface to be refinished.

VOC

The VOC content of this product in ready to use form is 0.00 g/liter.

Product storage

Product shelf life is determined when products are stored unopened at 70°F (20°C).

Avoid too much temperature fluctuation. o Product shelf life is 1 year

AkzoNobel Automotive and Aerospace Coatings, Inc Address: 3587 Parkway Lane, Norcross, GA 30092 Tel: 770-662-8464 FOR PROFESSIONAL USE ONLY IMPORTANT NOTE The information in this data sheet is not intended to be exhaustive and is based on the present state of our knowledge and on current laws: any person using the product for any purpose other than that specifically recommended in the technical data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. It is always the responsibility of the user to take all necessary steps to fulfill the demands set out in the local rules and legislation. Always read the Material Data Sheet and the Technical Data Sheet for this product if available. All advice we give or any statement made about the product by us (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing otherwise, we do not accept any liability whatsoever for the performance of the product or for any loss or damage arising out of the use of the product. All products supplied and technical advices given are subject to our standard terms and conditions of sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is subject to modification from time to time in the light of experience and our policy of continuous development. It is the user's responsibility to verify that this data sheet is current prior to using the product.

Brand names mentioned in this data sheet are trademarks of or are licensed to Akzo Nobel. Head Office Akzo Nobel Car Refinishes B.V., PO Box 3 2170 BA Sassenheim, The Netherlands. www.sikkenscr.com


© 2014 PPG Industries EB-143 12/14

Product Information ENVIROBASE

® High Performance Waterborne Basecoat

Product Description

Envirobase High Performance is a premium waterborne color system for use in repair and repainting of motor

vehicles. Industry leading color capability is easily achieved when applied as part of a two or three-stage basecoat/

clearcoat paint process. Mixed Envirobase High Performance color reproduces the original OEM solid, metallic,

mica, or XIRALLIC® paint finish of virtually all OEM manufacture's worldwide.

Envirobase High Performance products are engineered to reduce volatile organic compounds (VOC) and will

exceed all of today’s legislative VOC restrictions throughout the United States and Canada.

Envirobase High Performance waterborne color system is also capable of producing internal color as well as

interior color. For additional information, see Envirobase product bulletins EB145 for interior color and EB510 for

internal color.

Preparation of Substrate

Apply over original baked finishes or over recommended undercoats.

In all cases, wash all surfaces to be painted with soap and water. Final clean with an appropriate

waterborne cleaner. Ensure that the substrate is thoroughly cleaned and dried before starting

repair.

Apply Envirobase High Performance after sanding with European P800-P1200 / US 500-600

grade paper or dry sand with European P600-800 / US 500-600 grade paper.

Wash off residue and dry thoroughly before recleaning with appropriate waterborne substrate

cleaner. The use of a tack rag is recommended.

• Before mixing, gently hand shake bottles of the Envirobase High Performance toners for a few seconds before

use. Do not place toners or mixed color on shaker or mechanically agitate.

• Mixed Envirobase High Performance color should be thoroughly hand-stirred before application. If not used

immediately it should be hand-stirred again before use.

• Use nylon 125 micron paint filters specially designed for use with waterborne paint materials.


APPLICATION GUIDE:

Mixing Ratio:


T494/T595** 10% by volume for solid color

20% by volume for metallic / pearl color

30% by volume for tinted mid-coat color


T492 Adjuster* 10% by volume for solid color

Envirobase High Performance Metallic / Pearl Color 1 Part

T492 Adjuster* 10% by volume for metallic / pearl color

T494/T595** Thinner +10% by volume for metallic / pearl color

Envirobase High Performance Tinted Mid Coat Color 1 Part

T492 Adjuster* 10% by volume for tinted mid-coat color

T494/T595** Thinner +20% by volume for tinted mid-coat color

*T492 Adjuster has been specifically developed as an enhancement to the Envirobase High Performance basecoat system. Leading edge parts such as bumpers and fascia’s or low profile front ends that may be prone to stone chipping or when driving in extreme conditions

such as abrasive gravel roads or when subjected to high powered pressure washing, the addition of T492 adjuster will improve the

basecoat film properties. Note: Application, flash off and drying is the same as with the standard process. If additional reduction is required for viscosity adjustment, DO NOT add additional T492, use T494/T595 only.

** T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for additional information.

Pot Life

Un-activated, 90 days stored in sealed plastic containers. If activated, pot life is 2 hours.

Hand stir well before using. Do Not mechanically shake.

Additives T581 (optional activator) - 10% by volume after reducing. After activation, additional thinner may be

required to bring the color into the 23-28 second sprayable viscosity range.

Spraygun set up

Fluid Tip: 1.2 - 1.4 mm or equivalent

Spray Viscosity: 23 - 28 seconds, DIN4 @70°F (21°C)

Spray Pressure Color Coat Control Coat

HVLP at the air cap * *

Conventional at the spray gun * *

*Spray gun pressure will vary by manufacturer. See spray gun setup chart DOX440 on ppgrefinish.com

Envirobase / Technical Data Sheets & MSDS Index tab for manufacturer’s pressure information.

Number of Coats All repairs: 2-3 coats to coverage plus control coat*

Horizontal surfaces may require two control coats where vertical surfaces will generaly only require one

control coat.

*Note: A control coat is not required for solid colors.

Flash Off 70°F (21°C)

Between Coats: 1-2 minutes or until dried to a matt finish

Final Flash-off: When application is complete, apply the control coat and allow

it to dry naturally. Force drying of the control coat is not

necessary.

Note: Do not use the spray gun as an air drier. Use air drying equipment.

OR


APPLICATION GUIDE (cont’d):

Drying Times

Dust-Free Each coat approximately 2-4 minutes

70°F (21°C)

Dry to Handle Approximately 15-20 minutes

70°F (21°C)

Dry to De-Nib: Approximately 15-20 minutes

70°F (21°C)

Tape Time 5 minutes

70°F (21°C)

Dry to Clear 15 minutes minimum

70°F (21°C)

Note: Because of the intensity of IR curing, if the clearcoat is to be cured using IR the basecoat will first

need to be cured with IR to remove the residual moisture from the basecoat film.

Overcoat/Recoat

Overcoat with any compatible clear Flash off until the entire surface is touch-dry and has a uniform

matt appearance, or for 15 minutes.*

Dry Sand Use European P1500 / US 800 grit

Recoat After 24 hours, 1 coat of Envirobase High Performance must be

applied prior to the clearcoat application. The maximum recoat

time is 48 hours.

*Temperature, humidity, air movement and film build affect dry times. The best results are achieved with

increased temperature and air movement with minimal film builds.

BLENDING / WET BED

Mixing Ratio:

T490 Tinted Clear Additive 4 Parts

T494 / T595* Thinner 1 Part

For use as a blending additive: Add up to 1 equal par t of the T490 mixture to 1 par t of ready to spray

color and fade into the prepared blend panel.

or

For use as a wet bed: Apply 1 medium light coat of the T490 mixture to the blend panel and or the

entire repair panel and allow to dry. It will be milky blue when wet but will dry translucent. Once dry, apply

color. Be sure that whatever the wet bed material has been applied, it is completely covered with earlier

basecoat or clearcoat.

*T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for additional information.

3 STAGE PEARL PROCESS

Mixing Ratio: Ground Coat Pearl Coat

Color 1 part Color 1 part

T492/T494/T595* Thinner 10%** T292/T494/T595* Thinner 20%**

**Note: Percentage by volume. If using T492 Adjuster, see page 2 for proper use.

* T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for

additional information.


3 STAGE PEARL PROCESS (cont’d):

Viscosity & Pot Life:


Pot Life: 90 days stored in sealed plastic containers.

Always strain before use (nylon 125 micron is recommended).


Fluid Tip: 1.2 - 1.4 mm


HVLP * *

Compliant * *





• Avoid heavy application and excessive film

builds.

• Use air movement equipment to accelerate

drying as necessary. Choice of drying methods

will depend upon the type and size or the repair.

• A control coat is not required for solid color

basecoats.

Pearl Coat

• Horizontal and vertical surfaces


panels. Flash off thoroughly between coats.

• Apply the control coat and allow it to dry

naturally.

• Force drying of the control coat is not necessary.

The pearl color layer is not designed to give

opacity.

Flash Off:

Flash off until uniformly matt in appearance.

Dry Time: Wait until ground coat is uniformly dry before

applying pearl coat

Wait until pearl coat is uniformly dry before applying

clearcoat, approximately 15 minutes.

3 STAGE TINTED MID COAT PROCESS Mixing Ratio: Ground Coat

Color 1 part

T492/T494/T595* Thinner 20% **

Tinted Mid Coat

Color 1 part

T492/T494/T595 Thinner 30%**

** Note: Percentage by volume. If using T492 Adjuster, see page 2 for proper use. * T595 is for use in high heat, low humidity conditions only. See thinner selection guide on page 6 for additional information.

Viscosity & Pot Life


Pot Life: 90 days stored in sealed plastic containers

Always strain before use (nylon 125 micron is recommended)


Fluid Tip: 1.2 - 1.4 mm*


HVLP * *

Compliant * *



3 STAGE TINTED MID COAT PROCESS (cont’d):




• Apply the control coat onto dry film for even

metallic appearance.

Tinted Mid Coat


panels.


• The mid coat layer is not designed to give

opacity.

• Flash off the mid coat until it is uniformly dry

before applying clearcoat, approximately 15

minutes.

• A control coat is not required for the tinted

midcoat layer.

Compatibility

Low VOC Markets National Rule Markets




EC530 En.V™ Performance Clearcoat EC700 Series Clearcoats


EPW115 Waterborne Speed Prime




ECS6x A-Chromatic Sealer EC530 En.V Performance Clearcoat


EC800 Series Clearcoats EPW115 Waterborne Speed Prime

Minor Repair Guidelines

Dirt nibs or other defects in the Envirobase High Performance paint film may be repaired as follows: 1. Allow the surface to completely flash-off.

2. Dry sand the defect with P1500/US 800 grade paper or finer or with a fine abrasive pad or in combination with a small amount of SXA330 Wax and Grease

Remover as a sanding lubricant.

3. Remove sanding dust from the surface by strong air blowing with a clean air supply

4. Tack off surface with SX1070 tack rag.

5. Re-coat the surface with Envirobase High Performance as normal.

ONECHOICE® SXA1031 Aerosol Etch* (cut throughs only)


SX1071 Etch Prime**

SX1005 Low VOC wax and Grease Remover


Plastic Prep System*** (SU4901, SUA4903) SU470LV 1K Compliant Adhesion Promoter

OneChoice

SXA1031 Aerosol Etch* (cut throughs only)


SX1057 Flexible 2K Surfacer SX1060 Rollable 2K Primer Surfacer

Plastic Prep System*** (SU4901, SU4902, SU4903, SUA4903)

SX1005 Low VOC wax and Grease Remover SWX350 H2O-So-Clean

SU470LV 1K Compliant Adhesion Promoter


D8126


D820*** D8102 D8126

D800x* D8115 D8152

D8099** D8117 D893

D8101 D8150 D894

DELTRON® DPLV305x

DPLV Epoxy

NCP280*

DCU2010

DC3010

DC4010

DC4125

Deltron

DPS305x* DC2000

DVLP Epoxy DC3000

K36 DC4000

DCU2021 DC4125

DCU2042 DX179x***

DCU2060 DPX801***

DCU2082 DPLF*

* For optimum performance a 2K primer or sealer may be used. ** For optimum performance a 2K sealer may be used.

*** Must be primed or sealed.


Envirobase High Performance Waterborne Thinner Selection Guide

Note: Using T595 waterborne thinner with humidity levels above 30% can cause extremely slow flash and overall drying of the basecoat. Do not blend waterborne thinners as this will affect overall basecoat performance. Use either T494 or T595 depending on humidity.

Health and Safety See Material Safety Data Sheet and Labels for additional safety information and handling instructions.

• The contents of this package may have to be blended with other components before the product can be used. Before opening the

packages, be sure you understand the warning messages on the labels and MSDS of all the components, since the mixture will have the hazards of all its parts.

• Improper handling and use, for example, poor spray technique, inadequate engineering controls and/or lack of proper Personal

Protective Equipment (PPE), may result in hazardous conditions or injury.

• Follow spray equipment manufacturer’s instructions to prevent personal injury or fire.

• Provide adequate ventilation for health and fire hazard control.

• Follow company policy, product MSDS and respirator manufacturer’s recommendations for selection and proper sue of respiratory

protection. Be sure employees are adequately trained on the safe use of respirators per company and regulatory requirements.

• Wear appropriate PPE such as eye and skin protection. In the event of injury, see first aid procedures on MSDS.

• Always observe all applicable precautions and follow good safety and hygiene practices.

Equipment Cleaning

• Clean all mixing equipment immediately after use, preferably using a dedicated waterborne equipment cleaning machine with a final

rinse using waterborne thinner. Ensure all equipment is completely dry before storage or use.

• Envirobase High Performance tinters, Envirobase High Performance mixed color & waterborne thinner should be stored in a cool,

dry place away from sources of heat. During storage and transportation, temperature must be maintained at a minimum of 41°F or +5°C or and a maximum of 120°F or 49°C. Avoid exposure to frost or freezing conditions.

• Envirobase High Performance should be mixed in clean, dry plastic containers and equipment. Do not use mixing vessels or spray

equipment that contains solvent residues. Mixing vessels should ideally be plastic - if metal the container should be stainless steel or

have an internal anticorrosion coating.

• Store waterborne & solvent borne wastes separately. A competent agent with appropriate certification must handle all waterborne

wastes. Waste must be disposed of in accordance with all Federal, State, Provincial and local laws and regulations.

• Blended to spray basecoat color with T581 activator has a flash point above 200°F and may be disposed in the waterborne waste

stream intended for basecoat color (without activator). The waste disposal facility should be informed that the waste stream contains

isocyanates. T581 activator handled alone should be disposed in the solvent borne waste stream.

• The Envirobase High performance waterborne paint residues should be segregated from all other wastes and kept in a separate

closed lined container. The Envirobase High Performance waterborne paint residues must be disposed or in accordance with all Federal, State, Provincial and local laws and regulations.

Storage & Handling of Envirobase High Performance


TECHNICAL DATA

Theoretical coverage (RTS), giving 12.7µm (0.5 mils) dry film thickness, 274-640 sq. ft. per US gallon.

Percent solids by volume RTS 8.5 - 20.0%

RTS Combinations Color Color : T494/T595 Color : T494/T595 Color : T494/T595


Color Coating Color Coating Color Coating Color Coating

Ratio

Packaged 1 : 10% 1 : 20% 1 : 30%

Density (g/L) 991-1204 992-1186 992-1171 992-1156

Density (lbs./US gal.) 8.27-10.05 8.28-9.90 8.28-9.77 8.28-9.65

VOC Actual (g/L) 47-120 44-111 43-103 41-97

VOC Actual (lbs./ US gal.) 0.39-1.00 0.37-0.93 0.36-0.86 0.34-0.81

VOC Regulatory (g/L) 207-395 213-401 219-407 225-419

VOC Regulatory (lbs./US gal.) 1.73-3.30 1.78-3.35 1.83-3.40 1.88-3.50

Volatiles wt. %

60.42-84.97 63.42-86.29 66.01-87.44 68.26-88.40

Water wt. %

51.37-74.99 54.94-77.09 58.00-78.85 60.05-80.33

Exempt wt. %

0.0 0.0 0.0 0.0

Water vol. %

61.98-77.47 65.29-79.41 68.03-80.96 70.26-82.22

Exempt vol. %

0.0 0.0 0.0 0.0

RTS Combinations

Color : T494/T595 :

T581

Color : T494/T595 :

T581

Color : T494/T595 :

T581

T490 : T494/T595


Color Coating Color Coating Color Coating

Uniform Finish

Coating

Ratio

1 : 10% : 10% 1 : 20% : 10% 1 : 30% : 10% 4 : 1

Density (g/L) 998-1170 999-1158 998-1146 992

Density (lbs./US gal.) 8.33-9.76 8.34-9.66 8.33-9.56 8.28

VOC Actual (g/L) 70-119 67-112 63-105 91

VOC Actual (lbs./ US gal.) 0.58-0.99 0.56-0.94 0.53-0.88 0.76

VOC Regulatory (g/L) 252-359 256-370 261-373 380

VOC Regulatory (lbs./US gal.) 2.1-3.0 2.14-3.09 2.18-3.11 3.17

Volatiles wt. %

61.4-80.5 64.0-82.0 66.2-83.3 85.7

Water wt. %

51.2-70.0 54.3-72.1 57.0-74.0 76.6

Exempt wt. %

0.0 0.0 0.0 0.0

Water vol. %

60.0-72.1 63.0-74.1 65.5-75.8 76.1

Exempt vol. %

0.0 0.0 0.0 0.0





800.647.6050



888.310.4762

Follow us online:

www.ppgrefinish.com

The PPG Logo, Bringing innovation to the surface, Envirobase, OneChoice, Deltron, Global Refinish System, En.V, and H2O-So-Clean are trademarks of PPG Industries Ohio, Inc. Xirallic is a registered trademark of Merck Kgaa.

Emergency Medical or Spill Control Information: (412) 434-4515; In Canada (514) 645-1320

Materials described are designed for application by professional, trained personnel using proper equipment and are not intended for sale to the general public. Products mentioned may be hazardous and should only be used according to directions, while observing precautions and warning systems listed on label. Statements

and methods described are based upon the best information and practices known to PPG Industries. Procedures for applications mentioned are suggestions only and

are not to be construed as representations or warranties as to performance, result, or fitness for any intended use, nor does PPG Industries warrant freedom from patent infringement in the use of any formula or process set forth herein.

RTS Combinations Color : T492 Color : T492 : T494/T595 Color : T492 : T494/T595

Applicable Use Category Color Coating Color Coating Color Coating

Ratio 100 : 10% 100 : 10% : +10% 100 : 10% : +20%

Density (g/L) 995-1056 996-1050 996-1045

Density (lbs./US gal.) 8.30-8.81 8.31-8.76 8.31-8.72

VOC Actual (g/L) 55-102 52-95 48-87

VOC Actual (lbs./ US gal.) 0.46-0.84 0.43-0.79 0.40-0.73

VOC Regulatory (g/L) 216-403 219-405 223-407

VOC Regulatory (lbs./US gal.) 1.80-3.36 1.83-3.38 1.86-3.40

Volatiles wt. % 75.9-86.3 77.9-87.5 79.9-88.7

Water wt. % 70.8-80.1 73.0-81.6 75.2-83.1

Exempt wt. % 0.0 0.0 0.0

Water vol. % 72.1-80.3 74.2-81.7 76.3-83.1

Exempt vol. % 0.0 0.0 0.0

© 2014 PPG Industries EB-143SP 12/14

Información del producto Capa base ENVIROBASE® de Alto Rendimiento, soluble en agua

Descripción del producto

La capa base Envirobase de Alto Rendimiento es un sistema de colores soluble en agua y de alta calidad para utilizarse en la reparación y el repintado de vehículos motorizados. Se pueden lograr fácilmente propiedades de color líderes en la industria cuando se aplica como parte de un proceso de pintura de capa base/revestimiento transparente de dos o tres etapas. El color combinado de Envirobase de Alto Rendimiento reproduce el acabado de pintura original del fabricante de color sólido, metálico, mica o XIRALLIC® de prácticamente todos los fabricantes de equipos originales en el mundo.

Los productos Envirobase de Alto Rendimiento están diseñados para reducir los compuestos orgánicos volátiles (COV), y excederán todas las restricciones legislativas actuales sobre COV en todo el territorio de Estados Unidos y Canadá.

El sistema de color, soluble en agua, de Envirobase de Alto Rendimiento también tiene la capacidad de producir color interno como color interior. Para obtener más información, consulte los boletines de productos de Envirobase

EB145 para color interior y EB510 para color interno.

Preparación del sustrato

Aplique sobre acabados originales horneados o sobre capas base recomendadas.

En todos los casos, lave con agua y jabón todas las superficies que deben pintarse. La limpieza final debe realizarse con un limpiador en suspensión de agua adecuado. Verifique que el sustrato esté totalmente limpio y seco antes de empezar la reparación.

Aplique Envirobase de Alto Rendimiento después de lijar con papel lija grado P800 a P1200 europeo o grado 500 a 600 de EE. UU., o lije en seco con papel lija grado P600 a P800 europeo o 500 a 600 de de EE. UU.

Lave para eliminar todos los residuos y deje secar completamente antes de volver a limpiar con el limpiador en suspensión de agua adecuado. Se recomienda usar un trapo humedecido con disolvente.

• Antes de mezclar, agite suavemente a mano las botellas de los tóneres de Envirobase de Alto Rendimiento durante unos segundos antes de usarlos. No coloque los tóneres o colores mezclados en un agitador ni los agite mecánicamente.

• Los colores de Envirobase de Alto Rendimiento mezclados deben ser agitados completamente a mano antes de su aplicación. Si no se usan de inmediato, deben volverse a agitar a mano antes de usar.

• Use filtros de pintura de nailon de 125 micras diseñados especialmente para usar con pinturas en suspensión de agua.

© 2014 PPG Industries EB-143SP 12/14 2

GUÍA DE APLICACIÓN:


Color Envirobase de Alto Rendimiento 1 parte

T494/T595** 10% por volumen en color sólido

20% por volumen en color metálico / nacarado

30% por volumen en color de capa intermedia tonalizada

Color Envirobase de Alto Rendimiento 1 parte

Regulador T492* 10% por volumen en color sólido

Color Envirobase de Alto Rendimiento metálico / nacarado 1 parte

Regulador T492* 10% por volumen en color metálico / nacarado

Disolvente T494/T595** +10% por volumen en color metálico / nacarado

Color Envirobase de Alto Rendimiento de capa intermedia tonalizada 1 parte

Regulador T492* 10% por volumen en color de capa intermedia tonalizada

Disolvente T494/T595** +20% por volumen en color de capa intermedia tonalizada

*El Regulador T492 ha sido específicamente desarrollado como una mejora para el sistema de capas base Envirobase de Alto Rendimiento. Los bordes delanteros, como parachoques y tableros de instrumentos o los extremos delanteros inferiores pueden ser propensos a golpes con piedras como cuando se conduce en condiciones extremas, tales como caminos de grava o cuando se someten a un lavado de alta presión. La adición del Regulador T492 mejorará las propiedades de la capa base. Nota: La aplicación, secado por evaporación y secado generalizado son los mismos que en el proceso estándar. Si es necesario reducirlo aún más para ajustar la viscosidad, NO agregue T492 adicional; use solamente T494/T595

** T595 se debe usar solo en condiciones de alta temperatura y baja humedad. Para obtener más información, consulte la guía de selección de disolvente en la página 6.

Vida útil

Sin activar, 90 días almacenado en envases de plástico sellados. Si se activa, la vida útil es de 2 horas. Agite bien a mano antes de usar. No lo agite mecánicamente.

Aditivos T581 (activador opcional) - 10% por volumen después de diluir. Después de la activación, es posible que se requiera una cantidad adicional de disolvente para diluir el color y lograr los límites de viscosidad de la mezcla de 23 a 28 segundos.

Ajuste de la pistola

Boquilla: De 1,2 a 1,4 mm o equivalente

Viscosidad de rociado: De 23 a 28 segundos, DIN4 a 21 °C (70 °F)

Presión de rocío

Capa de color Capa de control HVLP en el tapón de aire * *

Convencional en la pistola de rociado * *

* La presión de la pistola de rociado variará según el fabricante. Consulte el cuadro sobre ajuste de la pistola de rociado DOX440 en ppgrefinish.com, pestaña de Índice Envirobase /Hojas de datos técnicos y MSDS para obtener información sobre la presión establecida por el fabricante.

Número de capas Todas las reparaciones: De 2 a 3 capas para cubrir más la capa de control*

Las superficies horizontales podrían requerir dos capas de control, en tanto que las superficies verticales por lo general requieren una capa de control.

*Nota: En el caso de colores sólidos, no se requiere una capa de control.

Evaporación 21 °C (70 °F)

Entre capas: De 1 a 2 minutos o hasta que seque con un acabado mate.

Secado final: Cuando haya terminado, aplique una capa de control y permita que seque de manera natural. No es necesario secar la capa de control de manera forzada.

Nota: No use la pistola como secador de aire. Use el equipo de secado de aire apropiado.

O


GUÍA DE APLICACIÓN (Cont.):

Tiempos de secado

Sin polvo Cada una de las capas aproximadamente de 2 a 4 minutos

21 °C (70 °F)

Seco para manipular Aproximadamente de 15 a 20 minutos

21 °C (70 °F)

Seco para pulir: Aproximadamente de 15 a 20 minutos

21 °C (70 °F)

Tiempo de encintado 5 minutos

21 °C (70 °F)

Seco para capa transparente 15 minutos como mínimo

21 °C (70 °F)

Nota: Debido a la intensidad del curado IR (infrarrojo), si el revestimiento transparente se cura con luz infrarroja, primero debe curarse la capa base con IR para eliminar la humedad residual de esta capa.

Recubrimiento/Nueva capa

Recubra con una capa transparente Seque hasta que toda la superficie esté seca al tacto y compatible tenga una apariencia mate uniforme, o durante 15 minutos*.

Lijado en seco Use papel lija de grano P1500 europeo o grano 800 de EE. UU.

Recubrir Después de 24 horas debe aplicarse una capa de Envirobase de Alto Rendimiento antes del revestimiento transparente. El tiempo máximo para recubrir es de 48 horas.

*La temperatura, la humedad, el movimiento del aire y la formación de la película afectan los tiempos de secado. Los mejores resultados se logran al incrementar la temperatura y el movimiento del aire con formación mínima de película.

MEZCLADO / CAPA INICIAL HÚMEDA


Aditivo transparente tonalizado T490 4 partes Disolvente T494 / T595* 1 parte

Para usar como aditivo de mezclado: Agregue hasta 1 par te igual de la mezcla T490 a 1 par te de la base de color lista para rociar y difumine en el panel de la mezcla preparada. o

Para usar como capa inicial húmeda: Aplique 1 capa medianamente ligera de la mezcla T490 al panel de mezcla y/o por todo el panel de reparación y deje secar. Esta capa tendrá un aspecto azul lechoso mientras esté húmeda, pero se tornará translúcida cuando seque. Una vez que esté seca, aplique la base de color. Cerciórese de que cualquiera que sea el material de capa inicial húmeda que se haya aplicado, éste quede cubierto primero con una capa base o transparente.

*T595 se debe usar solo en condiciones de alta temperatura y baja humedad. Para obtener más información, consulte la guía de selección de disolvente en la página 6.

PROCESO NACARADO DE 3 ETAPAS


Primera capa Capa nacarada

Color 1 parte Color 1 parte

Disolvente T492/T494/T595* 10%** Disolvente T292/T494/T595* 20%**

**Nota: Porcentaje por volumen. Si utiliza el Regulador T492, consulte la página 2 para conocer su uso apropiado.

* T595 se debe usar solo en condiciones de alta temperatura y baja humedad. Para obtener más información, consulte la guía de selección de disolvente en la página 6.


PROCESO NACARADO DE 3 ETAPAS (Cont.):

Viscosidad y vida útil:

Viscosidad: De 23 a 28 segundos DIN4 a 21 °C (70 °F)

Vida útil: 90 días almacenado en envases de plástico sellados.

Filtre siempre antes de usar (se recomienda nailon de 125 micras)

Pistola de rociado y presión de aire

Boquilla: De 1,2 a 1,4 mm

Capa de color Capa de control

HVLP * *

De conformidad * *

* La presión de la pistola de rociado variará según el fabricante. Consulte el cuadro sobre ajuste de la pistola de rociado DOX440 en ppgrefinish.com, pestaña de Índice Envirobase de Alto Rendimiento/Hojas de datos técnicos y MSDS para obtener información sobre la presión establecida por el fabricante.

Aplicación: Primera capa

• Aplique capas sencillas hasta lograr la opacidad deseada.

• Deje secar completamente entre capas. • Evite aplicar excesivamente y formar capas

gruesas. • Use equipo de movilización de aire para acelerar

el secado cuando sea necesario. La selección de métodos de secado dependerá del tipo y tamaño de la reparación.

• En el caso de las bases de colores sólidos, no se requiere una capa de control.

Capa nacarada

• Superficies horizontales y verticales

• Aplique capas ligeras sencillas con base en la verificación de color de los paneles. Deje secar completamente entre capas.

• Aplique la capa de control y déjela secar de manera natural.

• No es necesario secar la capa de control de manera forzada. La capa de color nacarado no está diseñada para ofrecer un aspecto opaco.

Evaporación:

Deje secar hasta lograr un aspecto mate uniforme.

Tiempo de secado:

Espere hasta que la primera capa seque de manera uniforme antes de aplicar la capa nacarada.

Espere aproximadamente 15 minutos hasta que la capa nacarada seque de manera uniforme antes de aplicar el revestimiento transparente.

PROCESO DE CAPA INTERMEDIA TONALIZADA DE 3 ETAPAS Proporciones de mezcla:

Primera capa

Color 1 parte

Disolvente T492/T494/T595* 20% **

Capa intermedia tonalizada

Color 1 parte

Disolvente T492/T494/T595 30%**

** Nota: Porcentaje por volumen. Si utiliza el Regulador T492, consulte la página 2 para conocer su uso apropiado. * T595 se debe usar solo en condiciones de alta temperatura y baja humedad. Para obtener más información, consulte la guía de selección de disolvente en la página 6.

Viscosidad y vida útil

Viscosidad: De 23 a 28 segundos DIN4 a 21 °C (70 °F)

Vida útil: 90 días almacenado en envases de plástico sellados

Filtre siempre antes de usar (se recomienda nailon de 125 micras)

Pistola de rociado y presión de aire

Boquilla: De 1,2 a 1,4 mm*

Capa de color Capa de control

HVLP * *

De conformidad * *

* La presión de la pistola de rociado variará según el fabricante. Consulte el cuadro sobre ajuste de la pistola de rociado DOX440 en ppgrefinish.com, pestaña de Índice Envirobase de Alto Rendimiento/Hojas de datos técnicos y MSDS para obtener información sobre la presión establecida por el fabricante.


PROCESO DE CAPA INTERMEDIA TONALIZADA DE 3 ETAPAS (Cont.):

Aplicación: Primera capa

• Aplique capas sencillas hasta lograr la opacidad deseada.

• Deje secar completamente entre capas. • Aplique la capa de control sobre la película seca

para un aspecto metálico uniforme.

Capa intermedia tonalizada

• Aplique capas ligeras sencillas con base en la verificación de color de los paneles.

• Deje secar completamente entre capas. • La capa intermedia no está diseñada para ofrecer

un aspecto opaco. • Espere aproximadamente 15 minutos hasta que

la capa intermedia seque de manera uniforme antes de aplicar el revestimiento transparente.

• En el caso de capas intermedias tonalizadas no se requiere una capa de control.

Compatibilidad

Mercados de bajo COV Mercados de Normas Nacionales

Envirobase de Alto Rendimiento

Tapaporos acromático ECP1x**

Sellador LV acromático ECS2x

Revestimiento transparente En.V™ EC530

Revestimientos transparentes EC700

Revestimientos transparentes serie EC800

Imprimador de secado rápido de suspensión en agua EPW115

Envirobase de Alto Rendimiento

Tapaporos acromático ECP1x**

Sellador LV acromático ECS2x

Sellador acromático ECS6x

Revestimiento transparente En.V EC530

Revestimientos transparentes EC700

Revestimientos transparentes serie EC800

Imprimador de secado rápido de suspensión en agua EPW115

Pautas para reparaciones menores

Las incrustaciones de polvo u otros defectos en la película de pintura Envirobase de Alto Rendimiento pueden repararse de

la manera siguiente: 1. Deje que la superficie seque por completo. 2. Lije el defecto en seco con papel lija grado P1500 o 800 de EE. UU. o más fino o con una almohadilla abrasiva fina, o junto con una cantidad reducida de

removedor de cera y grasa SXA330 como lubricante para lijar. 3. Elimine el polvo de lijado de la superficie con un chorro fuerte de aire limpio. 4. Limpie toda la superficie con un trapo humedecido en disolvente SX1070. 5. Vuelva a recubrir la superficie con Envirobase de Alto Rendimiento de manera normal.

ONECHOICE® Decapante en aerosol SXA1031* (solo para recortes) Imprimación de adhesión plástica SXA1050**

Imprimador decapante SX1071**

Removedor de cera y grasa de bajo COV SX1005


Sistema de preparación plástica*** (SU4901, SUA4903) SU470LV Promotor de adherencia de conformidad 1K

OneChoice

Decapante en aerosol SXA1031* (solo para recortes) Imprimación de adhesión plástica SXA1050**

SX1057 Tapaporos flexible 2K

SX1060 Imprimador tapaporos laminable 2K

Sistema de preparación plástica*** (SU4901, SU4902, SU4903, SUA4903) Removedor de cera y grasa de bajo COV SX1005

SWX350 H2O-So-Clean

SU470LV Promotor de adherencia de conformidad 1K


D8126


D820*** D8102 D8126

D800x* D8115 D8152

D8099** D8117 D893

D8101 D8150 D894

DELTRON® DPLV305x

DVLP epóxico

NCP280*

DCU2010

DC3010

DC4010

DC4125

Deltron

DPS305x* DC2000

DPLV epóxico DC3000

K36 DC4000

DCU2021 DC4125

DCU2042 DX179x***

DCU2060 DPX801***

DCU2082 DPLF*

* Para un rendimiento óptimo, puede usarse un imprimador o sellador 2K. ** Para un rendimiento óptimo, puede usarse un sellador 2K

***Debe imprimarse o sellarse.


Guía de selección de disolventes en suspensión de agua de Envirobase® de Alto Rendimiento

Nota: Usar el disolvente en suspensión de agua T595 con niveles de humedad por encima del 30% puede provocar un secado por evaporación excesivamente lento y el secado generalizado de la capa base. No combine los disolventes en suspensión de agua ya que podrían afectar el rendimiento general de la capa base. Dependiendo del nivel de humedad, utilice el disolvente T494 o T595.

Salud y seguridad Para obtener información adicional sobre seguridad e instrucciones de manipulación, consulte las hojas de datos de seguridad de materiales (MSDS) y las etiquetas. • El contenido de este paquete tal vez deba mezclarse con otros componentes antes de utilizarse. Antes de abrir los paquetes, asegúrese de que

entiende los mensajes de advertencia en las etiquetas y hojas de datos de seguridad de materiales (MSDS) de todos los componentes, ya que la mezcla tendrá los riesgos de todas sus partes.

• La manipulación y el uso inadecuados, por ejemplo, una técnica de rociado deficiente, controles de ingeniería inadecuados y/o la falta de equipo de protección personal (PPE) apropiado, pueden provocar condiciones peligrosas o lesiones.

• Siga las instrucciones del fabricante del equipo de rociado para prevenir lesiones físicas o incendios.

• Proporcione la ventilación adecuada para la salud y para controlar el riesgo de incendio.

• Siga la política de la empresa, las hojas de datos de seguridad de materiales (MSDS) y las instrucciones del fabricante del respirador para elegir y usar la protección respiratoria adecuada. Asegúrese de que los empleados hayan recibido la capacitación adecuada sobre el uso seguro de respiradores conforme a los requisitos reglamentarios y de la empresa.

• Use el equipo de protección personal (PPE) apropiado, por ejemplo, protección para los ojos y la piel. En caso de lesiones, consulte los procedimientos de primeros auxilios en las MSDS.

• Respete siempre todas las precauciones pertinentes y siga las prácticas apropiadas de seguridad e higiene.

Limpieza del equipo

• Limpie todo el equipo de mezclado inmediatamente después de usarlo, de preferencia con una máquina limpiadora de equipos en suspensión de agua designada únicamente para este fin, y un enjuague final con disolvente en suspensión de agua. Verifique que todo el equipo esté completamente seco antes de usarlo o guardarlo.

• Los tintes Envirobase de Alto Rendimiento, los colores mezclados Envirobase de Alto Rendimiento y el disolvente en suspensión de agua deben guardarse en un lugar fresco y seco, lejos de las fuentes de calor. Durante el almacenamiento y transporte, la temperatura debe mantenerse en +5 °C o 41 °F como mínimo y en 49 °C o 120 °F, como máximo. Evite la exposición a la escarcha o a condiciones que provoquen congelamiento.

• Envirobase de Alto Rendimiento debe mezclarse en equipos y envases de plástico, limpios y secos. No use recipientes de mezclado o equipos de rociado que contengan residuos de disolventes. Los recipientes de mezclado deben ser preferentemente de plástico; si son metálicos, deben ser de acero inoxidable o tener un revestimiento interno anticorrosivo.

• Guarde los residuos en suspensión de agua y con partículas de solvente de manera separada. Un agente experto que cuente con la certificación apropiada debe manipular todos los residuos en suspensión de agua. Los residuos deben ser eliminados de acuerdo a todas las leyes y reglamentos federales, estatales, provinciales y locales.

• La mezcla del sistema de color de capa base lista para rociar con el activador T581 tiene un punto de ignición por encima de 93 °C (200 °F) y se puede verter en el flujo para residuos de pinturas solubles en agua destinado para capas base de color (sin activador). Se debe notificar a la fábrica de eliminación de residuos que el flujo de residuos contiene isocianatos. El activador T581 manipulado independientemente debe verterse en el flujo de residuos con partículas de solvente.

• Los residuos de pintura en suspensión de agua Envirobase de Alto Rendimiento deben separarse de todos los demás residuos y guardarse en un recipiente revestido cerrado aparte. Los residuos de pintura en suspensión de agua Envirobase de Alto Rendimiento deben ser eliminados de acuerdo a todas las leyes y reglamentos federales, estatales, provinciales y locales.

Almacenamiento y manipulación de Envirobase de Alto Rendimiento


DATOS TÉCNICOS

Rendimiento teórico (RTS), proporciona un espesor de película seca de 12,7 µm (0.5 mils), 274-640 pies2 por galón de EE. UU. Porcentaje de sólidos por volumen RTS de 8,5 a 20,0%

Combinaciones RTS Color Color : T494/T595 Color : T494/T595 Color : T494/T595

Categoría de uso aplicable Revestimiento de color Revestimiento de color Revestimiento de color Revestimiento de color

Proporción Empaquetado 1 : 10% 1 : 20% 1 : 30%

Densidad (g/l) De 991 a 1204 De 992 a 1186 De 992 a 1171 De 992 a 1156

Densidad (lb/gal. de EE.UU.) De 8,27 a 10,05 De 8,28 a 9,90 De 8,28 a 9,77 De 8,28 a 9,65

COV real (g/l) De 47 a 120 De 44 a 111 De 43 a 103 De 41 a 97

COV real (lb/gal de EE. UU.) De 0,39 a 1,00 De 0,37 a 0,93 De 0,36 a 0,86 De 0,34 a 0,81

COV reglamentario (g/l) De 207 a 395 De 213 a 401 De 219 a 407 De 225 a 419

COV reglamentario (lb/gal de

EE.UU.) De 1,73 a 3,30 De 1,78 a 3,35 De 1,83 a 3,40 De 1,88 a 3,50

% de peso de volátiles De 60,42 a 84,97 De 63,42 a 86,29 De 66,01 a 87,44 De 68,26 a 88,40

% de peso de agua De 51,37 a 74,99 De 54,94 a 77,09 De 58,00 a 78,85 De 60,05 a 80,33

% de peso de exentos 0,0 0,0 0,0 0,0

% de volumen de agua De 61,98 a 77,47 De 65,29 a 79,41 De 68,03 a 80,96 De 70,26 a 82,22

% de volumen de exentos 0,0 0,0 0,0 0,0

Combinaciones RTS

Color : T494/T595 :

T581

Color : T494/T595 :

T581

Color : T494/T595 :

T581

T490 : T494/T595

Categoría de uso aplicable

Revestimiento de color

Revestimiento de color Revestimiento de color Capa de acabado

uniforme

Proporción 1 : 10% : 10% 1 : 20% : 10% 1 : 30% : 10% 4 : 1

Densidad (g/l) De 998 a 1170 De 999 a 1158 De 998 a 1146 992

Densidad (lb/gal. de EE.UU.) De 8,33 a 9,76 De 8,34 a 9,66 De 8,33 a 9,56 8,28

COV real (g/l) De 70 a 119 De 67 a 112 De 63 a 105 91

COV real (lb/gal de EE. UU.) De 0,58 a 0,99 De 0,56 a 0,94 De 0,53 a 0,88 0,76

COV reglamentario (g/l) De 252 a 359 De 256 a 370 De 261 a 373 380


EE.UU.) De 2,1 a 3,0 De 2,14 a 3,09 De 2,18 a 3,11 3,17

% de peso de volátiles De 61,4 a 80,5 De 64,0 a 82,0 De 66,2 a 83,3 85,7

% de peso de agua De 51,2 a 70,0 De 54,3 a 72,1 De 57,0 a 74,0 76,6

% de peso de exentos 0,0 0,0 0,0 0,0

% de volumen de agua De 60,0 a 72,1 De 63,0 a 74,1 De 65,5 a 75,8 76,1

% de volumen de exentos 0,0 0,0 0,0 0,0


Acabado Automotriz PPG



800.647.6050



888.310.4762

Búsquenos en Internet:

www.ppgrefinish.com

El logotipo de PPG Logo, Bringing innovation to the surface, Envirobase, OneChoice, Deltron, Global Refinish System, En.V y H2O-So-Clean son marcas comerciales de PPG Industries Ohio, Inc. Xirallic es una marca comercial registrada de Merck Kgaa.

Información sobre emergencias médicas y control de derrames: (412) 434-4515; en Canadá al (514) 645-1320

Los materiales descritos están diseñados para ser aplicados únicamente por personal profesionalmente capacitado, utilizando el equipo apropiado, y sin la intención de ser vendidos al público en general. Los productos mencionados pueden ser peligrosos y deberán usarse únicamente de acuerdo a las instrucciones, al tiempo que se respetan todas las precauciones y sistemas de advertencia enumerados en la etiqueta. Las declaraciones y los métodos descritos se basan en las mejores prácticas e información conocidas a la fecha por PPG Industries. Los procedimientos de aplicación mencionados son sugerencias únicamente y no deben ser considerados como representaciones o garantías del desempeño, resultados o idoneidad de cualquier uso deseado. PPG Industries no garantiza que no se incurra en incumplimiento de patentes ante el uso de cualquier fórmula o proceso descrito en el presente documento.

Combinaciones RTS Color : T492 Color : T492 : T494/T595 Color : T492 : T494/T595

Categoría de uso aplicable Revestimiento de color Revestimiento de color Revestimiento de color

Proporción 100 : 10% 100 : 10% : +10% 100 : 10% : +20%

Densidad (g/l) De 995 a 1056 De 996 a 1050 De 996 a 1045

Densidad (lb/gal. de EE.UU.) De 8,30 a 8,81 De 8,31 a 8,76 De 8,31 a 8,72

COV real (g/l) De 55 a 102 De 52 a 95 De 48 a 87

COV real (lb/gal de EE. UU.) De 0,46 a 0,84 De 0,43 a 0,79 De 0,40 a 0,73

COV reglamentario (g/l) De 216 a 403 De 219 a 405 De 223 a 407


EE.UU.) De 1,80 a 3,36 De 1,83 a 3,38 De 1,86 a 3,40

% de peso de volátiles De 75,9 a 86,3 De 77,9 a 87,5 De 79,9 a 88,7

% de peso de agua De 70,8 a 80,1 De 73,0 a 81,6 De 75,2 a 83,1

% de peso de exentos 0,0 0,0 0,0

% de volumen de agua De 72,1 a 80,3 De 74,2 a 81,7 De 76,3 a 83,1

% de volumen de exentos 0,0 0,0 0,0

Waterborne Pre-Cleaner

SWX350 H2O-So-Clean™ Waterborne Pre-Cleaner

SWX350 H2O-So-Clean™ is a superior waterborne surface cleaner used for removing most contaminations including wax and grease, mold release agents and sanding dust.

SWX350 is commonly referred to as simply “O-so-clean” thanks to its excellent cleaning ability. It is compliant in the most stringent VOC markets with an ultra low 0.21 VOC.

OC-9

Features

· Packaged ready for use· Produces consistent results

Advantages

· Can be used with PPG or Nexa Autocolor systems

Benefits

· Customer satisfaction


Required Products

· SWX350 H2O-So-Clean™ Waterborne Pre-Cleaner

Compatible Products

· SWX350 Waterborne Pre-cleaner is for use with PPG and Nexa Autocolor brand products.

Compatible Substrates

· OEM Surfaces· Cured and Dried Automotive Surfaces· Ferous and non-ferous metals· Automotive Plastics

Application Data

Application:· SWX350 is packaged ready for use.

· Apply a generous amount of SWX350 on the surface with a clean cloth or a hand held spray bottle and wipe the surface clean. This initial step floats the contaminants to the surface.

· Use a second clean cloth to wipe the surface clean and remove the contaminants.

· For maximum results, wipe dry with clean cloth while the surface is still wet, to eliminate smearing of contaminants.

Technical Data:

Color ClearIntended Use Solvent (Substrate Cleaner)Packaged (ready to use) VOC content 0.16 lbs/gal (19 g/L)Density 8.15 lbs/galFlashpoint (PMCC) 62°F (17°C)

Important: Before opening the packages, be sure you understand the warning messages on the labels of all components, since the mixture will have the hazards of all its parts. Improper spray technique may result in a hazardous condition. Follow spray equipment manufacturer’s instructions to prevent personal injury or fire. Follow directions for respirator use. Wear eye and skin protection. Observe all applicable precautions.

H2O-So-Clean™ Waterborne Pre-Cleaner SWX350

See material Safety Data Sheet and Labels for additional safety information and handling instructions.

EMERGENCY MEDICAL OR SPILL CONTROL INFORMATION (412) 434 -4515. IN CANADA (514) 645-1320Materials described are designed for application by professional, trained personnel using proper equipment and are not intended for sale to the general public. Products mentioned may be hazardous and should only be used according to directions, while observing precautions and warning statements listed on label. Statements and methods described are based upon the best information and practices known to PPG Industries. Procedures for applications mentioned are suggestions only and are not to be construed as representations or warranties as to performance, results, or fitness for any intended use, nor does PPG Industries warrant freedom from patent infringement in the use of any formula or process set forth herein.

PPG IndustriesWorld Leaders in Automotive Finishes

PPG Industries PPG Canada Inc.19699 Progress Drive 2301 Royal Windsor Drive, Unit #6Strongsville, OH 44149 Mississauga, Ontario, Canada L5J 1K5 1-800-647-6050 1-888-310-4762

© 2009 PPG Industries www.ppgrefinish.com Part No. OC-9 11/09

P-246 DELTRON® Ultra Velocity Clearcoat

DC2000

Features Compatible Surfaces ● Fast air dry ● ENVIROBASE® High Performance Waterborne Basecoat ● Sand and buff in 30 minutes or less

● Deltron 2000 (DBC) Basecoat ● GLOBAL REFINISH SYSTEMl® BC Basecoat

● Fully cured and sanded OEM and refinish paints

Advantages Required Products

● Faster throughput

DC2000 Ultra Velocity Clearcoat

DCH2015 Hardener

DR220 Medium Temperature Accelerated Reducer (70°- 85°F / 21°- 29°C)

DT885 Mid Temperature Thinner (75 - 90°F / 24° - 32°C)

DT895 High Temperature Thinner (85 - 95°F / 29° - 35°C)

DT898 Very High Temperature Thinner (95°F and above / 35°C and above)

D871 Medium Thinner (65° - 77°F /18° - 25°C )

D872 Slow Thinner (77° - 95°F / 25° - 35°C )

D873 Very Slow Thinner (95°F and above / 35°C and above)

● Performs well in all booth types ● Speeds up assembly and delivery time

Benefits

● Increased production ● Reduces cycle times

DC2000 is an ultra velocity, high quality clearcoat, specifically developed to enhance productivity in air-dry collision repair facilities and also reduces energy cost in facilities with baking booths. Deltron

Ultra Velocity Clearcoat is designed for use on repairs of 1- 4 panels. DC2000 offers extremely fast flash, polish and air dry times without sacrificing durability or appearance.


DC2000

Directions For Use

Preparation:

Refer to the specific product Information bulletin of the color system for its application, dry times, and blend recommendations.

Mixing Ratios:

DC2000 : DCH2015 : DR220/DT8xx/D8xx

4 parts : 1 part : ½ to 1 part

Pot Life:

2 hours at 70ºF (21ºC)

Additives:

DX814

Flexibilizer


4 parts : 1 part : ½ to 1 part + 10%

DX73

Fisheye

Eliminator


4 parts : 1 part : ½ to 1 part + 1 oz. to RTS qt.

For flattening recommendations, see OneChoice® bulletin OC-2

Application Coats:

Apply: 2 medium wet coats with no flash between coats Air Pressure:

HVLP: 10 psi at the air cap Compliant: 29 - 40 psi at the gun Conventional: 45 - 55 psi at the gun Note : For best overall results, refer to spraygun manufacturers recommendation for inlet air pressures.

Spray Gun Set-up:

Fluid Tip: Film Build Per Wet Coat Dried Film Build Per Coat:

1.3 - 1.5 mm or equivalent 2 - 3 mils 1 - 1.5 mils

Page 2 P-246

Directions For Use

Drying Times:

Between Coats: 70ºF / 21ºC

No flash required

Dust Free: 70ºF / 21ºC

9-12 minutes

Tape Time: 70ºF / 21ºC

1 hour

Air Dry to Re-assemble: 70ºF / 21ºC

1 hour

Force Dry: 140ºF / 60ºC

Not Recommended

IR

Not Recommended

Polishing: Air Dry

70ºF / 21ºC

25- 30 minutes

Repair and Recoat:

2 - 3 hours air dry 70ºF (21ºC)

DC2000 must be sanded before recoating with primer, color or clear.

Equipment Cleaning: Spray guns, gun cups, storage pots, etc., should be cleaned thoroughly

after each use with any appropriate PPG general purpose solvent.

Page 3 P-246

DC2000

Deltron Ultra

Velocity Clearcoat Technical Data: VOC less exempt solvents (Applied 4:1:1) 4.03 - 4.17 lbs/gal (483 – 500 g/l)

VOC less exempt solvents w/DX814 (Applied 4:1:1+10%) 4.37 - 4.44 lbs/gal (524 – 532 g/l)

VOC less exempt solvents w/DX73 (Applied 4:1:1+1 oz. RTS qt.) 4.17 - 4.27 lbs/gal (500 – 512 g/l) VOC less exempt solvents w/SU4985 (Applied X:X:X:X) 5.04 - 5.26 lbs/gal (604 – 630 g/l)

Total Solids by Volume (Applied 4:1:1) 35.1%

Sq. Ft Coverage / US Gal (Applied 4:1:1) 564 @ 1 mil, 100% transfer efficiency

Important: The contents of this package must be blended with other components before the product can be used. Before opening the packages, be sure you understand the warning messages on the labels of all components, since the mixture will have the hazards of all its parts. Improper spray technique may result in a hazardous condition. Follow spray equipment manufacturer’s instructions to prevent personal injury or fire. Follow directions for respirator use. Wear eye and skin protection. Observe all applicable precautions.

See Material Safety Data Sheet and Labels for additional safety information and handling instructions.

EMERGENCY MEDICAL OR SPILL CONTROL INFORMATION (412) 434-4515; IN CANADA (514) 645-1320

Materials described are designed for application by professional, trained personnel using proper equipment and are not intended for sale to the public. Products mentioned may be hazardous and should only be used according to directions, while observing precautions and warning statements listed on label. Statements and methods described are based upon the best information and practices known to PPG Industries. Procedures for applications mentioned are suggestions only and are not to be construed as representations or warranties as to performance, results, or fitness for any intended use, nor does PPG Industries warrant freedom from patent infringement in the use of any formula or process set forth herein.



PPG Canada Inc. 2301 Royal Windsor Drive Unit #6 Mississauga, Ontario L5J 1K5 1-888-310-4762 The PPG logo, Deltron, Envirobase, Global Refinish System, OneChoice and Bringing innovation to the surface are registered trademarks of

PPG Industries Ohio, Inc. © 2013 PPG Industries www.ppgrefinish.com Part No. P-246, 12/13


December 2014



1/2

Description

UltraPrep Surface Cleaner is a waterbased surface cleaner with low VOC content. UltraPrep Surface Cleaner is used to ensure removal of all kinds of contamination from the substrate prior to paint application.

Suitable Substrates

Steel

Stainless Steel Zinc Coated Steel Aluminum Existing Finishes Plastic Substrate

Cleaning technique

After washing the car or the surface of the body panel under treatment, wet a clean cloth with the

UltraPrep Surface Cleaner and clean the surface under treatment. Immediately thereafter, wipe the surface thoroughly dry with high quality absorbent surface cleaning cloths. Always use two cloths, as one cloth will merely shift rather than remove dirt and grease. Do not allow the surface cleaner to evaporate on substrate or the contamination on the surface will remain. Wipe the substrate thoroughly dry before the surface cleaner evaporates. The purpose of surface cleaning is to remove residual grease, oil, wax, silicones, sand, etc. If this is not done, residual contaminant will remain in scratch marks during sanding. Adhesion of the paint system subsequently applied to the contaminated surface will be poor and could delaminate.

o Replace cloths being used for cleaning regularly by clean ones. Instead of placing used (wet) rags in a sealed container place them on the floor grating so that the solvents can evaporate, then place the dried cloths in the regular dustbin.

Point of attention on surface cleaning:

Salt residue and blistering:

With all cleaning activities: once the surface under treatment has been cleaned, it must never be touched with the bare hand; as salts, moisture and oils can be transferred to the prepared surface which may result in delamination or blistering problems. It is particularly important that hand protecting barrier creams are never used near an automobile that is to be refinished. Should you still have touched a sanded and cleaned surface with bare hands; clean it again with first one of the solvent borne and next with one of the water borne cleaners again according the recommended cleaning technique. Truck body constructions:

It is important to prevent dirt residues from getting into construction joints of vans, lorries, etc. during cleaning . They might cause adhesion problems when the paint is applied. Vertically fitted parts should, therefore, first be the surface should be cleaned from the bottom upwards and subsequently from the top downwards.


December 2014



2/2

Point of attention on surface cleaning continued):

Cleaning and condensation on metal surfaces:

After a surface has been cleaned, solvent will evaporate. Heat needed for evaporation is withdrawn from that surface, making it colder than the surrounding atmosphere, which results in (often not visible) condensation on the surface. Allow the moisture sufficient time to evaporate. The first coat of paint can be applied as soon as the surface has re-gained the temperature of the surrounding atmosphere. Earlier application of the coat may lead to adhesion problems. The same problem may arise if a vehicle is transferred from a cold room to a warm one or from outdoors to indoors. Allow vehicles a minimum of one hour to acclimatize. Double-walled vehicles (and certainly insulated ones) require some hours to acclimatize.

Health and Safety

Akzo Nobel Car Refinishes recommends providing adequate ventilation during surface cleaning with any of the mentioned cleaners. Where reasonably practicable, this should be achieved by the use of local exhaust ventilation and good general extraction. If these are not sufficient to maintain concentrations of particulates and solvent vapours below the OEL, suitable respiratory protection must be worn. Besides respiratory protection, always wear solvent resistant gloves while surface cleaning even though working with a low solvent degreaser. This will reduce the risk of cleaning solvents being absorbed into the skin and prevent salts and oils on your hands from contaminating the surface to be refinished.

VOC

The VOC content of this product in ready to use form is 0.00 g/liter.

Product storage

Product shelf life is determined when products are stored unopened at 70°F (20°C).

Avoid too much temperature fluctuation. o Product shelf life is 1 year

AkzoNobel Automotive and Aerospace Coatings, Inc Address: 3587 Parkway Lane, Norcross, GA 30092 Tel: 770-662-8464 FOR PROFESSIONAL USE ONLY IMPORTANT NOTE The information in this data sheet is not intended to be exhaustive and is based on the present state of our knowledge and on current laws: any person using the product for any purpose other than that specifically recommended in the technical data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. It is always the responsibility of the user to take all necessary steps to fulfill the demands set out in the local rules and legislation. Always read the Material Data Sheet and the Technical Data Sheet for this product if available. All advice we give or any statement made about the product by us (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing otherwise, we do not accept any liability whatsoever for the performance of the product or for any loss or damage arising out of the use of the product. All products supplied and technical advices given are subject to our standard terms and conditions of sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is subject to modification from time to time in the light of experience and our policy of continuous development. It is the user's responsibility to verify that this data sheet is current prior to using the product.

Brand names mentioned in this data sheet are trademarks of or are licensed to Akzo Nobel. Head Office Akzo Nobel Car Refinishes B.V., PO Box 3 2170 BA Sassenheim, The Netherlands. www.sikkenscr.com


Product Information - SkillsUSA Minnesota...ENVIROBASE® High Performance Waterborne Basecoat...

Documents

Transcript of Product Information - SkillsUSA Minnesota...ENVIROBASE® High Performance Waterborne Basecoat...