PRODUCT INFORMATION DuPont™ Zytel 70G35EF NC010...Relative permittivity, 1MHz 4.1 / 4.7 - IEC...

PRODUCT INFORMATION

DuPont™ Zytel® 70G35EF NC010NYLON RESINProduct InformationCommon features of Zytel® nylon resin include mechanical and physical properties such as high mechanical strength, excellent balance of stiffness and toughness, good high temperatureperformance, good electrical and flammability properties, good abrasion and chemical resistance. In addition, Zytel® nylon resins are available in different modified and reinforced grades to

create a wide range of products with tailored properties for specific processes and end-uses. Zytel® nylon resin, including most flame retardant grades, offer the ability to be coloured. The good melt stability of Zytel® nylon resin normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option,incineration with energy recovery (-31kJ/g of base polymer) in appropriately equipped installations. For disposal, local regulations have to be observed. Zytel® nylon resin typically is used in demanding applications in the automotive, furniture, domestic appliances, sporting goods and construction industry.

Zytel® 70G35EF NC010 is a 35% glass reinforced polyamide 66 developed for electrical and electronics applications.

Product information Value Unit Test StandardResin Identification PA66-GF35 - ISO 1043Part Marking Code PA66-GF35 - ISO 11469

Rheological properties dry / cond Unit Test StandardMolding shrinkage, parallel 0.4 / - % ISO 294-4, 2577Molding shrinkage, normal 1.0 / - % ISO 294-4, 2577

Mechanical properties dry / cond Unit Test StandardTensile Modulus 1.6E6 / 1.23E6 psi ISO 527-1/-2Stress at break 29000 / 20300 psi ISO 527-1/-2Strain at break 3.5 / 4.6 % ISO 527-1/-2Flexural Modulus 1.45E6 / 1.09E6 psi ISO 178Flexural Strength 42100 / 33400 psi ISO 178Tensile creep modulus ISO 899-1

1h * / 1.23E6 psi1000h * / 870000 psi

Charpy impact strength ISO 179/1eU73°F 42.8 / 47.6 ftlb/in²-22°F 38.1 / 38.1 ftlb/in²

Charpy notched impact strength ISO 179/1eA73°F 6.66 / 8.56 ftlb/in²-22°F 5.23 / 4.76 ftlb/in²-40°F 5.71 / - ftlb/in²

Puncture energy, 73°F 6 / - J ISO 6603-2Izod notched impact strength ISO 180/1A

73°F 7.14 / - ftlb/in²-40°F 6.18 / - ftlb/in²

Thermal properties dry / cond Unit Test StandardMelting temperature, 18°F/min 500 / * °F ISO 11357-1/-3Glass transition temperature, 18°F/min 158 / 68 °F ISO 11357-1/-2Temp. of deflection under load ISO 75-1/-2

260 psi 482 / * °F1200 psi 230 / * °F

Vicat softening temperature, 90°F/h, 11 lbf 491 / * °F ISO 306Coeff. of linear therm. expansion, parallel 9.44E-6 / * in/in/°F ISO 11359-1/-2Coeff. of linear therm. expansion, normal 4.72E-5 / * in/in/°F ISO 11359-1/-2Thermal conductivity of melt 0.24 W/(m K) -Spec. heat capacity of melt 2130 J/(kg K) -

Flammability dry / cond Unit Test StandardOxygen index 24 / * % ISO 4589-1/-2Glow Wire Flammability Index, 80mil 1200 / - °F IEC 60695-2-12

Page: 1 of 21Revised: 2019-05-13

To find out more, visit DuPont Performance Polymers or contact nearest DuPont location.

North America Asia Pacific Europe/Middle East/AfricaTel: +1 302 999-4592Toll-Free (USA): 800 441-0575

Tel: +81 3 5521 8600 Tel: +41 22 717 51 11

Copyright 2017 DuPont. The DuPont Oval Logo is a trademark or registered trademark of E.I. du Pont de Nemours andCompany or its affiliates. All rights reserved.

http://www.dupont.com/products-and-services/plastics-polymers-resins/thermoplastics.html

DuPont™ Zytel® 70G35EF NC010NYLON RESIN

FMVSS Class B - ISO 3795 (FMVSS 302)Burning rate, Thickness 1 mm 1.02 in/min ISO 3795 (FMVSS 302)

Electrical properties dry / cond Unit Test StandardRelative permittivity, 1MHz 4.1 / 4.7 - IEC 62631-2-1Dissipation factor, 1MHz 140 / 620 E-4 IEC 62631-2-1Volume resistivity >1E13 / 1E9 Ohm*m IEC 62631-3-1Electric strength 914 / 787 kV/in IEC 60243-1Comparative tracking index 575 / - - IEC 60112

Other properties dry / cond Unit Test StandardHumidity absorption, 80mil 1.7 / * % Sim. to ISO 62Water absorption, 80mil 5.5 / * % Sim. to ISO 62Density 1.4 / - g/cm³ ISO 1183Density of melt 77.4 lb/ft³ -

VDA Properties dry / cond Unit Test StandardOdor test 3 class VDA 270Fogging, G-value (condensate) 0.5 / * mg ISO 6452

Injection dry / cond Unit Test StandardDrying Recommended yes -Drying Temperature ≤176 °F -Drying Time, Dehumidified Dryer 2 - 4 h -Processing Moisture Content ≤0.2 % -Melt Temperature Optimum 563 °F -Min. melt temperature 545 °F -Max. melt temperature 581 °F -Max. screw tangential speed 0.2 / * m/s -Mold Temperature Optimum 212 °F -Min. mold temperature 158 °F -Max. mold temperature 248 °F -Hold pressure range 7250 - 14500 psi -Hold pressure time 0.0762 s/mil -Ejection temperature 410 °F -

CharacteristicsInjection MoldingProcessingPelletsDelivery formRelease agentAdditivesNorth AmericaEurope

Asia PacificSouth and Central America

Near East/AfricaGlobal

Regional Availability




Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




Diagrams

Viscosity-shear rate

Shear rate in 1/s

Vis

cosi

ty in

Pa.

s

1E2 1E3 1E41E1

1E2

1E3 545 °F563 °F581 °F

Shearstress-shear rate

Shear rate in 1/s

She

arst

ress

in p

si

1E2 1E3 1E41E3

1E4

1E5 545 °F563 °F581 °F




Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




Stress-strain (dry)

B

B

B

B

B

B

B

B

Strain in %

Str

ess

in p

si

0 1 2 3 4 5 6 70

10000

20000

30000

40000 -4 °F32 °F73 °F

104 °F140 °F194 °F248 °F302 °F

B - Break




Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




Stress-strain (cond.)

BB

B

B

B

B

B

B

Strain in %

Str

ess

in p

si

0 1 2 3 4 5 60

5000

10000

15000

20000

25000

30000

35000 -4 °F32 °F73 °F

104 °F140 °F194 °F248 °F302 °F

B - Break




Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




Secant modulus-strain (dry)

BBB

B

BB

B

B

Strain in %

Sec

ant m

odul

us in

psi

0 1 2 3 4 5 6 70

200000

400000

600000

800000

1000000

1200000

1400000

1600000 -4 °F32 °F73 °F

104 °F140 °F194 °F248 °F302 °F

B - Break




Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




Secant modulus-strain (cond.)

BBB

BB B

B

B

Strain in %

Sec

ant m

odul

us in

psi

0 1 2 3 4 5 6200000

400000

600000

800000

1000000

1200000

1400000

1600000 -4 °F32 °F73 °F

104 °F140 °F194 °F248 °F302 °F

B - Break




Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




Stress-strain (isochronous) 73°F(cond.)

Strain in %

Str

ess

in p

si

0 0.5 1 1.5 20

2000

4000

6000

8000

10000

12000 0.1 h1 h

10 h100 h

1000 h




Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




Creep modulus-time 73°F(cond.)

Time in h

Cre

ep m

odul

us in

psi

1E-1 1E0 1E1 1E2 1E3600000

700000

800000

900000

1000000

1100000

1200000

1300000 1450 psi2901 psi4351 psi5802 psi7252 psi8702 psi

10150 psi11600 psi




Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




Stress-strain (isochronous) 212°F(dry)

Strain in %

Str

ess

in p

si

0 0.1 0.2 0.3 0.4 0.5 0.6 0.70

1000

2000

3000

4000

5000 1 h10 h

100 h1000 h

Page: 10 of 21Revised: 2019-05-13



Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




Creep modulus-time 212°F(dry)

Time in h

Cre

ep m

odul

us in

psi

1E0 1E1 1E2 1E3650000

700000

750000

800000

850000

900000 725.2 psi1450 psi2176 psi2901 psi3626 psi4351 psi

Page: 11 of 21Revised: 2019-05-13



Tel: +81 3 5521 8600 Tel: +41 22 717 51 11





Strain in %

Str

ess

in p

si

0 0.5 1 1.5 20

1000

2000

3000

4000

5000

6000

7000 0.1 h1 h

10 h100 h

1000 h

Page: 12 of 21Revised: 2019-05-13



Tel: +81 3 5521 8600 Tel: +41 22 717 51 11





Time in h

Cre

ep m

odul

us in

psi

1E-1 1E0 1E1 1E2 1E3300000

350000

400000

450000

500000

550000 1450 psi2901 psi4351 psi5802 psi6527 psi

Page: 13 of 21Revised: 2019-05-13



Tel: +81 3 5521 8600 Tel: +41 22 717 51 11





Strain in %

Str

ess

in p

si

0 0.5 1 1.5 20

1000

2000

3000

4000

5000

6000 0.1 h1 h

10 h100 h

1000 h

Page: 14 of 21Revised: 2019-05-13



Tel: +81 3 5521 8600 Tel: +41 22 717 51 11





Time in h

Cre

ep m

odul

us in

psi

1E-1 1E0 1E1 1E2 1E3300000

350000

400000

450000

500000

550000 725.2 psi1450 psi2176 psi2901 psi3626 psi4351 psi5076 psi5802 psi

Page: 15 of 21Revised: 2019-05-13



Tel: +81 3 5521 8600 Tel: +41 22 717 51 11





B

Strain in %

Str

ess

in p

si

0 0.5 1 1.5 2 2.5 3 3.50

2000

4000

6000

8000 1 h10 h

100 h1000 h

B - Break

Page: 16 of 21Revised: 2019-05-13



Tel: +81 3 5521 8600 Tel: +41 22 717 51 11





Time in h

Cre

ep m

odul

us in

psi

1E0 1E1 1E2 1E3200000

250000

300000

350000

400000

450000

500000 1450 psi2901 psi4351 psi5802 psi7252 psi

Specific volume-temperature (pvT)

Temperature in °F

Spe

c. v

olum

e in

E-3

m³/

kg

0 100 200 300 400 500 6000.68

0.7

0.72

0.74

0.76

0.78

0.8

0.82

0.84 14.5 psi5802 psi

17400 psi29010 psi

Page: 17 of 21Revised: 2019-05-13



Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




Tensile modulus-temperature (dry)

Temperature in °F

Ten

sile

mod

ulus

in p

si

-50 0 50 100 150 200 250 300 3501E5

1E6

1E7

Tensile modulus-temperature (cond.)

Temperature in °F

Ten

sile

mod

ulus

in p

si

-50 0 50 100 150 200 250 300 3501E5

1E6

1E7

Page: 18 of 21Revised: 2019-05-13



Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




Chemical Media Resistance

Acids

Acetic Acid (5% by mass) (23°C)

Citric Acid solution (10% by mass) (23°C)

Lactic Acid (10% by mass) (23°C)

Hydrochloric Acid (36% by mass) (23°C)

Nitric Acid (40% by mass) (23°C)

Sulfuric Acid (38% by mass) (23°C)

Sulfuric Acid (5% by mass) (23°C)

Chromic Acid solution (40% by mass) (23°C)

Bases

Sodium Hydroxide solution (35% by mass) (23°C)

Sodium Hydroxide solution (1% by mass) (23°C)

Ammonium Hydroxide solution (10% by mass) (23°C)

Alcohols

Isopropyl alcohol (23°C)

Methanol (23°C)

Ethanol (23°C)

Hydrocarbons

n-Hexane (23°C)

Toluene (23°C)

iso-Octane (23°C)

Ketones

Acetone (23°C)

Ethers

Diethyl ether (23°C)

Mineral oils

SAE 10W40 multigrade motor oil (23°C)

SAE 10W40 multigrade motor oil (130°C)

SAE 80/90 hypoid-gear oil (130°C)

Insulating Oil (23°C)

Hydraulic oil Pentosin CHF 202 (125°C)

Standard Fuels

ISO 1817 Liquid 1 - E5 (60°C)

ISO 1817 Liquid 2 - M15E4 (60°C)

ISO 1817 Liquid 3 - M3E7 (60°C)

ISO 1817 Liquid 4 - M15 (60°C)

Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23°C)

Page: 19 of 21Revised: 2019-05-13



Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23°C)

Diesel fuel (pref. ISO 1817 Liquid F) (23°C)

Diesel fuel (pref. ISO 1817 Liquid F) (90°C)

Diesel fuel (pref. ISO 1817 Liquid F) (>90°C)

Diesel EN 590 (100°C)

Salt solutions

Sodium Chloride solution (10% by mass) (23°C)

Sodium Hypochlorite solution (10% by mass) (23°C)

Sodium Carbonate solution (20% by mass) (23°C)

Sodium Carbonate solution (2% by mass) (23°C)

Zinc Chloride solution (50% by mass) (23°C)

Other

Ethyl Acetate (23°C)

Hydrogen peroxide (23°C)

DOT No. 4 Brake fluid (130°C)

DOT No. 4 Brake fluid (120°C)

Ethylene Glycol (50% by mass) in water (108°C)

1% nonylphenoxy-polyethyleneoxy ethanol in water (23°C)

50% Oleic acid + 50% Olive Oil (23°C)

Water (23°C)

Water (90°C)

Phenol solution (5% by mass) (23°C)

Symbols used:

possibly resistantDefined as: Supplier has sufficient indication that contact with chemical can be potentially accepted under the intended use conditions andexpected service life. Criteria for assessment have to be indicated (e.g. surface aspect, volume change, property change).

not recommended - see explanationDefined as: Not recommended for general use. However, short-term exposure under certain restricted conditions could be acceptable (e.g. fastcleaning with thorough rinsing, spills, wiping, vapor exposure).

Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 160 mil (Hytrel® measured at 80 mil), IEC Electrical properties measured at 80 mil, all ASTM propertiesmeasured at 120 mil, and test temperatures are 73°F unless otherwise stated.

The information set forth herein is furnished free of charge and is based on technical data that DuPont believes to be reliable and falls withinthe normal range of properties. It is intended for use by persons having technical skill, at their own discretion and risk. This data should not beused to establish specification limits nor used alone as the basis of design. Handling precaution information is given with the understanding thatthose using it will satisfy themselves that their particular conditions of use present no health or safety hazards. Since conditions of product useand disposal are outside our control, we make no warranties, express or implied, and assume no liability in connection with any use of thisinformation. As with any product, evaluation under end-use conditions prior to specification is essential. Nothing herein is to be taken as alicense to operate or a recommendation to infringe on patents. Caution: Do not use in medical applications involving permanent implantation inthe human body. For other medical applications, discuss with your DuPont customer representative and read Medical Caution H-50103-5.

Page: 20 of 21Revised: 2019-05-13



Tel: +81 3 5521 8600 Tel: +41 22 717 51 11




DuPont™, the DuPont Oval Logo, and all products, unless otherwise noted, denoted with ™, ℠ or ® are trademarks, service marks or registeredtrademarks of affiliates of DuPont de Nemours, Inc. © 2019 DuPont de Nemours, Inc. All rights reserved.

Page: 21 of 21Revised: 2019-05-13



Tel: +81 3 5521 8600 Tel: +41 22 717 51 11



PRODUCT INFORMATION DuPont™ Zytel 70G35EF NC010...Relative permittivity, 1MHz 4.1 / 4.7 - IEC...

Documents

Transcript of PRODUCT INFORMATION DuPont™ Zytel 70G35EF NC010...Relative permittivity, 1MHz 4.1 / 4.7 - IEC...