PRODUCT DATA SHEET PRODUCT DATA SHEET ... for the PREMIER label of quality. PREMIER PLASTICS ......
2
Look for the PREMIER label of quality. PREMIER PLASTICS ... ‘Good Solid Tanks’ Look for the PREMIER label of quality. PREMIER PLASTICS ... ‘Good Solid Tanks’ PRODUCT DATA SHEET Represented by: PREMIER PLASTICS low profile SUPERTANK ™ Specifications over page. H SEPTIC TANKS (also above ground) H SEWAGE TREATMENT PLANTS H WATER STORAGE H TOUGH ONE-PIECE POLYETHYLENE H SUPER STRONG TRIANGULAR RIBBING H EASY INSTALLATION (Model STS900D or STSU1000EH shown) FEB 2012 www.premierplastics.com Toll-Free: 1-800-661-4473
-
Upload
nguyenhanh -
Category
Documents
-
view
233 -
download
4
Transcript of PRODUCT DATA SHEET PRODUCT DATA SHEET ... for the PREMIER label of quality. PREMIER PLASTICS ......
Look for the PREMIER label of quality. PREMIER PLASTICS ... ‘Good Solid Tanks’ Look for the PREMIER label of quality. PREMIER PLASTICS ... ‘Good Solid Tanks’Look for the PREMIER label of quality. PREMIER PLASTICS ... ‘Good Solid Tanks’ Look for the PREMIER label of quality. PREMIER PLASTICS ... ‘Good Solid Tanks’
PRODUCT DATA SHEET PRODUCT DATA SHEET
8328 River Way, Delta, BC, Canada V4G 1C4Bus: (604) 952-6686 Fax: (604) 952-6696Toll Free: 1-800-661-4473E-mail: [email protected]
8328 River Way, Delta, BC, Canada V4G 1C4Bus: (604) 952-6686 Fax: (604) 952-6696Toll Free: 1-800-661-4473E-mail: [email protected]
Represented by: Represented by:
PREMIER PLASTICS low profile
SUPERTANK™
PREMIER PLASTICS low profile
SUPERTANK™
Specifications over page. Specifications over page.
H SEPTIC TANKS (also above ground)H SEWAGE TREATMENT PLANTSH WATER STORAGE
H SEPTIC TANKS (also above ground)H SEWAGE TREATMENT PLANTSH WATER STORAGE
H TOUGH ONE-PIECE POLYETHYLENEH SUPER STRONG TRIANGULAR RIBBINGH EASY INSTALLATION
H TOUGH ONE-PIECE POLYETHYLENEH SUPER STRONG TRIANGULAR RIBBINGH EASY INSTALLATION
PREMIERP L A S T I C S I N C .
PREMIERP L A S T I C S I N C .
(Model STS900D or STSU1000EH shown) (Model STS900D or STSU1000EH shown)
FEB 2012 SEPT. 09/REV. 1
www.premierplastics.com Toll-Free: 1-800-661-4473
U.S.A. U.S. gal. Model No. Dimensions
900 STCU 900EH* 48”h x 100”l x 83”wSeptic Tank 1000 STSU 1000EH* 56”h x 100”l x 83”w(2 chamber) 1300 STSU 1300EH* 64”h x 100”l x 83”w 1500 STSU 1500EH* 75”h x 100”l x 83”w
1080 STCU 1080EH 48”h x 100”l x 83”w 1260 STCU 1260EH 56”h x 100”l x 83”wWater Cistern 1500 STCU 1500EH 64”h x 100”l x 83”w 1800 STCU 1800EH 75”h x 100”l x 83”w
U.S.A. U.S. gal. Model No. Dimensions
900 STCU 900EH* 48”h x 100”l x 83”wSeptic Tank 1000 STSU 1000EH* 56”h x 100”l x 83”w(2 chamber) 1300 STSU 1300EH* 64”h x 100”l x 83”w 1500 STSU 1500EH* 75”h x 100”l x 83”w
1080 STCU 1080EH 48”h x 100”l x 83”w 1260 STCU 1260EH 56”h x 100”l x 83”wWater Cistern 1500 STCU 1500EH 64”h x 100”l x 83”w 1800 STCU 1800EH 75”h x 100”l x 83”w
PRODUCT DATA SHEET
SUPERTANK™ outline specifications:
Material: High density linear polyethylene (safe for food contact-water tanks). Meets FDA regulations 21 CFR 177.1520(C) 3.1 Wall thickness – 0.35” +/- .03”.
Meets CSA and ANSI/NSF61 for drinking water.
Plumbing: Septic tanks are pre-plumbed with 4” solvent weld PVC pipe connections, Tee Y’s, dip tubes and inspection plugs to local plumbing codes. (No plumbing in water cisterns.)
Partition: Rigid 1½” thick plastic board. (Optional in some locations.)
Access Lids: Two nom. 24” dia. Heavy duty molded polyethylene. Each lid safety secured with 6 corrosion resistant screws. NOTE: Cistern tanks may be sealed watertight with silicone sealant under lid.
Risers: Risers for direct access from the ground surface fit over manway lids on the tank. Riser base must be lag screwed and glued to top of tank. An additional lid on the riser provides additional safety and security. (Lid on tank must remain in place for structural integrity.) See separate sheet for risers.
Water Table: Maximum allowable – 1’ above water level in tank to limit deflection in tank base. (Install dip tube on outside of tank.)
Installation: Maximum dirt cover above top of tank – 2.5’ (EH models - 4’). Use GRANULAR BACKFILL ONLY. Remove rocks from tank surface, compact evenly underneath and around tank. Lids must be secured in place when backfilling. Use extra heavy weight, two chamber tank in wet soils. NO WATER NEEDED IN TANK WHEN BACKFILLING. Refer to full installation instructions. Dead load test – 12,000 lbs.
Warranty: Premier Plastics below ground tanks are warranted for 100 years against defects and degradation in the material.
(See full warranty sheet.)
(see full instruction sheet)
PRODUCT DATA SHEET
SUPERTANK™ outline specifications:
Material: High density linear polyethylene (safe for food contact-water tanks). Meets FDA regulations 21 CFR 177.1520(C) 3.1 Wall thickness – 0.35” +/- .03”.
CSA and ANSI/NSF61 approved.
Plumbing: Septic tanks are pre-plumbed with 4” solvent weld PVC pipe connections, Tee Y’s, dip tubes and inspection plugs to local plumbing codes. (No plumbing in water cisterns.)
Partition: Rigid 1½” thick plastic board. (Optional in some locations.)
Access Lids: Two nom. 24” dia. Heavy duty molded polyethylene. Each lid safety secured with 6 corrosion resistant screws. NOTE: Cistern tanks may be sealed watertight with silicone sealant under lid.
Risers: Risers for direct access from the ground surface fit over manway lids on the tank. Riser base must be lag screwed and glued to top of tank. An additional lid on the riser provides additional safety and security. (Lid on tank should remain in place for structural integrity.) See separate sheet for risers. Tanks accommodate 24” dia. Polylok and UltraRib risers.
Water Table: Maximum allowable – 1’ above water level in tank to limit deflection in tank base. (Install dip tube on outside of tank.)
Installation: Maximum dirt cover above top of tank – 4 ft. Use GRANULAR BACKFILL ONLY. Remove rocks from tank surface, compact evenly underneath and around tank. Lids must be secured in place when backfilling. Use extra heavy weight, two chamber tank in wet soils. NO WATER NEEDED IN TANK WHEN BACKFILLING. Refer to full installation instructions. CSA dead load test – 25,000 lbs.
Warranty: Premier Plastics below ground tanks are warranted for 10 years against defects and degradation in the material.
(See full warranty sheet.)
What are TRIANGULAR RIBS™?
The unique Triangular Ribs™ are unparalleled in ability to resist vertical and horizontal ground pressure. The series of short, flat, triangular surfaces keeps the direction of the forces in line with each rib, thus substantially increasing stiffness compared with curved ribbed tanks. In curved ribbed tanks, approximately 50% of the curved wall surface area is capable of resisting vertical loads, whereas 100% of the wall surface area of Triangular Ribs™ contributes to the load bearing capacity of the tank.
The importance of WALL THICKNESS % Increase
Increase in wall thickness 5 10 20 30 50
Increase in stiffness 16 33 73 120 230
FOR EXAMPLE: A tank with 3/8” wall thickness will be more than 3 times stiffer than a tank with ¼” wall thickness.
*Installation subject to local health regulations.*Installation subject to local health regulations.
FEB 2012
Load Load
Curved ribs –poor load bearing
Butterfly Ribs™ –high load-bearing
No cornerthinning
Rounded CornersSquare CornersEffect ofmold constructionon wall thickness Fracture
point
Contact factory for Advanced Treatment Unit applications.Add EH for extra-heavy models.
Contact factory for Advanced Treatment Unit applications.
SELECTION GUIDE SELECTION GUIDE
(see full instruction sheet)
Triangular Ribshigh load-bearing
(Model STS1125D or STSU1300EH shown) (Model STS1125D or STSU1300EH shown)
What are TRIANGULAR RIBS™?
The unique Triangular Ribs™ are unparalleled in ability to resist vertical and horizontal ground pressure. The series of short, flat, triangular surfaces keeps the direction of the forces in line with each rib, thus substantially increasing stiffness compared with curved ribbed tanks. In curved ribbed tanks, approximately 50% of the curved wall surface area is capable of resisting vertical loads, whereas 100% of the wall surface area of Triangular Ribs™ contributes to the load bearing capacity of the tank.
The importance of WALL THICKNESS % Increase
Increase in wall thickness 5 10 20 30 50
Increase in stiffness 16 33 73 120 230
FOR EXAMPLE: A tank with 3/8” wall thickness will be more than 3 times stiffer than a tank with ¼” wall thickness.
NOV. 2010
Load Load
Curved ribs –poor load bearing
Butterfly Ribs™ –high load-bearing
No cornerthinning
Rounded CornersSquare CornersEffect ofmold constructionon wall thickness Fracture
point
Triangular Ribshigh load-bearing
PIPING MAY VARY
CANADA Imp. gal. Model No. Dimensions
750 STS 1750D* 48”h x 100”l x 83”wSeptic Tank 900 STS 1900D* 56”h x 100”l x 83”w(2 chamber) 1125 STS 1125D* 64”h x 100”l x 83”w 1350 STS 1350D* 75”h x 100”l x 83”w
750 STS 1750S* 48”h x 100”l x 83”wSeptic Tank 900 STS 1900S* 56”h x 100”l x 83”w(1 chamber) 1125 STS 1125S* 64”h x 100”l x 83”w 1350 STS 1350S* 75”h x 100”l x 83”w
900 STC 1900 48”h x 100”l x 83”w 1050 STC 1050 56”h x 100”l x 83”wWater Cistern 1250 STC 1250 64”h x 100”l x 83”w 1500 STC 1500 75”h x 100”l x 83”w
CANADA Imp. gal. Model No. Dimensions
750 STS 1750D* 48”h x 100”l x 83”wSeptic Tank 900 STS 1900D* 56”h x 100”l x 83”w(2 chamber) 1125 STS 1125D* 64”h x 100”l x 83”w 1350 STS 1350D* 75”h x 100”l x 83”w
750 STS 1750S* 48”h x 100”l x 83”wSeptic Tank 900 STS 1900S* 56”h x 100”l x 83”w(1 chamber) 1125 STS 1125S* 64”h x 100”l x 83”w 1350 STS 1350S* 75”h x 100”l x 83”w
900 STC 1900 48”h x 100”l x 83”w 1050 STC 1050 56”h x 100”l x 83”wWater Cistern 1250 STC 1250 64”h x 100”l x 83”w 1500 STC 1500 75”h x 100”l x 83”w
