ProASICPLUS Evaluation Board · APA-EVAL-BRD1 This board contains all the surrounding circuitry,...

QS_Tutorial_eval.book Page i Monday, January 13, 2003 1:08 PM

ProASICPLUS Evaluation Board

User’s Guide

QS_Tutorial_eval.book Page ii Monday, January 13, 2003 1:08 PM

Actel Corporation, Sunnyvale, CA 94086© 2002 Actel Corporation. All rights reserved.

Printed in the United States of America

Part Number: 51700003-0

Release: December 2002

No part of this document may be copied or reproduced in any form or by any means without prior written consent of Actel.

Actel makes no warranties with respect to this documentation and disclaims any im-plied warranties of merchantability or fitness for a particular purpose. Information in this document is subject to change without notice. Actel assumes no responsibil-ity for any errors that may appear in this document. This document contains confidential proprietary information that is not to be dis-closed to any unauthorized person without prior written consent of Actel Corpora-tion. Trademarks Actel and the Actel logotype are registered trademarks of Actel Corporation.

Adobe and Acrobat Reader are registered trademarks of Adobe Systems, Inc.

Liberty is a licensed trademark of Synopsys Inc. This product uses SDC, a Propri-etary format of Synopsys Inc.

Libero is a trademark of Actel Corporation.

Mentor Graphics, Viewlogic, ViewDraw, MOTIVE, and ModelSim are registered trademarks of Mentor Graphics, Inc.

Synplify and Synplicity are registered trademarks of Synplicity, Inc.

Verilog is a registered trademark of Open Verilog International.

WaveFormer Lite and SynaptiCAD are trademarks of SynaptiCAD, Inc.

Windows is a registered trademark and Windows NT is a trademark of Microsoft Corporation in the U.S. and other countries.

All other products or brand names mentioned are trademarks or registered trade-marks of their respective holders.

ii

QS_Tutorial_eval.book Page iii Monday, January 13, 2003 1:08 PM

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Document Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Document Assumptions . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Contents and System Requirements . . . . . . . . . . . . . . . . 7Evaluation Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 7System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2 Setup and Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . .9Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Testing the Evaluation Board. . . . . . . . . . . . . . . . . . . . . . . . 9Programming the Test file . . . . . . . . . . . . . . . . . . . . . . . . 10

3 Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . 11Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Programming Headers . . . . . . . . . . . . . . . . . . . . . . . . . . 12Clock Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

A Board Connections . . . . . . . . . . . . . . . . . . . . . . . . . 17

B Board Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

C Product Support . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Actel U.S. Toll-Free Line . . . . . . . . . . . . . . . . . . . . . . . . . 35Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Customer Applications Center . . . . . . . . . . . . . . . . . . . . . . 36Guru Automated Technical Support . . . . . . . . . . . . . . . . . . . 36Web Site. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36FTP Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Contacting the Customer Applications Center . . . . . . . . . . . . . . 36Worldwide Sales Offices . . . . . . . . . . . . . . . . . . . . . . . . . 38

iii

QS_Tutorial_eval.book Page iv Monday, January 13, 2003 1:08 PM

QS_Tutorial_eval.book Monday, January 13, 2003 1:08 PM

Introduction

Thank you for purchasing Actel’s ProASICPLUS Evaluation Board.

The purpose of this user’s guide is to provide you with information so you can easily evaluate the ProASICPLUS devices.

This is the first release of the user’s guide. The most up-to-date version of this guide is available at:

http://www.actel.com/products/tools/hw.html

Document ContentsChapter 1 - Contents and System Requirements describes the contents of the ProASICPLUS Evaluation Kit.

Chapter 2 - Setup and Self Test describes how to setup the ProASICPLUS Evaluation Board and how to perform a self test.

Chapter 3 - Hardware Description describes the components of the ProASICPLUS Evaluation Board.

Appendix A - Board Connections lists a board connection table.

Appendix B - Board Schematics show illustrations of the ProASICPLUS Evaluation Board.

Appendix C - Product Support describes our support services.

Document AssumptionsThis user’s guide assumes the following:

• You intend to use Actel’s Libero software.

• You have installed and are familiar with Actel’s Libero software.

• You are familiar with the VHDL or Verilog hardware description language.

• You are familiar with UNIX workstations and operating systems or PCs and Windows operating systems.

5



1Contents and System Requirements

This chapter describes the differences between the three versions of the ProASICPLUS evaluation board. This chapter also details the contents of the ProASICPLUS evaluation kit and provides power supply and software system requirements.

Evaluation Kit ContentsThe ProASICPLUS evaluation kit has three board versions.

Note: There is no socket on these boards.

APA-EVAL-BRD1

This board contains all the surrounding circuitry, but no APA device. For this board, it is assumed that you will acquire a device and solder it to the board yourself. This allows you to use the board with any device in the APA family.

APA-EVAL-BRD300

Same as BRD1 but with an APA300 device mounted.

APA-EVAL-BRD075

Same as BRD1 but with an APA075 device mounted.

When you purchase any of the above board versions, you also receive the following:

• Evaluation board - one of the three listed above

• The ProASICPLUS Evaluation Board User’s Guide

• Customer Letter

• CD with design examples

For the CD contents, review the ReadMe.doc file at the top level of the CD. As more design examples become available, the CD contents will change. For the latest design examples, refer to the Hardware Tools section of the Actel website:


7


Chapter 1: Contents and System Requirements


Power Supply and Software RequirementsThis section describes power supply and software requirements for the ProASICPLUS evaluation kit.

Power Supply The ProASICPLUS evaluation board requires the following:

• Wall mount power supply

• 9V, 500mA supply with 2.1mm female connector P5 type

• Digikey part number T413-P5P-ND for US

• Digikey part number T408-P5P-ND for Europe

Software Each ProASICPLUS evaluation board requires a different version of the software.

APA-EVAL-BRD075

This board can use the free evaluation Libero Silver version, which does not include simulation. To include simulation, use the Libero Gold version.

APA-EVAL-BRD300

This board requires a full Libero Platinum license.

APA-EVAL-BRD1

With the blank board, you can select any device from the ProASICPLUS family in a 208 PQFP footprint and solder it to the board yourself.

Use the appropriate software for the device you choose. For software support details, refer to the Actel Website:

http://www.actel.com/products/tools/support.html

8

http://www.actel.com/products/tools/support.html


2Setup and Self Test

Software InstallationSince this package does not include software, this guide does not provide software installation instructions. For software installation instructions, refer to the Actel Installation and Licensing Guide at:

http://www.actel.com/products/tools/libero/docs.html

Testing the Evaluation BoardIf the evaluation board is shipped directly from Actel, it contains a test program that determines if the board works properly.

To test the evaluation board:

1. Supply power to the board.

2. Turn on the ON/OFF switch.

3. Perform the actions described in Table 2-1.

Table 2-1. Evaluation Board Test

Action Result Pass/Fail

Press PB1 multiple times, but not too fast A sequence of LEDs light up Pass

Press and hold SW1 All LEDs are unlit Pass

Press and hold SW2 All LEDs light up except DS1 Pass

Press and hold SW3A random sequence of LEDs light up while you hold the switch

Pass

Press and hold SW4 The LED is lit/unlit in a 01101010 pattern Pass

Any two switches are pressed together Creates a 00100110 pattern. Pass

9

http://www.actel.com/products/tools/libero/docs.html

Chapter 2: Setup and Self Test


Programming the Test fileIf you want to retest the evaluation board, you can reprogram the board using the test program at any time. Use the STAPL file test.stp or the bitstream file test.bit. These files are included on the Evaluation Kit CD. Table 2-2 describes the actions you should perform when retesting your evaluation board.

This design is currently implemented for the APA300 device. If you have a device of a different size, you can recompile the design into other device sizes. The design files are available under actelprj/eval in the Evaluation Kit CD.

For instructions on programming the device using Flash Pro, refer to the Flash Pro User’s Guide at:

http://www.actel.com/techdocs/manuals/docs/flashproUG.pdf

Table 2-2. Retesting the Evaluation Board

Action Result Pass/Fail

Press PB1 multiple times, but not too fast

Count sequence should be visible on the LED Pass

Press and hold SW1 All LEDs are unlit Pass

Press and hold SW2 All LEDs are lit Pass

Press and hold SW3 Count sequence runs while you hold the switch Pass

Press and hold SW4 LED is lit/unlit alternately in a 10101010 pattern Pass

Any two switches are pressed together Creates a 00110011 pattern Pass

10

http://www.actel.com/techdocs/manuals/docs/flashproUG.pdf


3Hardware Description

This chapter describes the components of the evaluation board. See Figure 3-1 for a schematic of the evaluation board.

Figure 3-1. ProASICPlus Evaluation Board

The ProASICPlus evaluation board consists of the following:

• Wall mount power supply connector, with switch and LED indicator

• Jumper to select between 2.5V and 3.3V I/O voltages

• 40MHz oscillator and manual clock option

11

Chapter 3: Hardware Description


• Small program header (compatible with both Flash Pro and Silicon Sculptor)

• Four switches (provides input to the device)

• eight LED (driven by outputs from the device)

• Jumpers (allows disconnection of all external circuitry from the FPGA)

For further information, refer to the following appendices:

Appendix A – Board Connections

Appendix B – Board Schematics

Power Supplies The evaluation board requires the following power supplies:

• Wall mount power supply

• 9V, 500mA supply with 2.1mm female connector P5 type

Digikey part number T413-P5P-ND for US

Digikey Part Number T408-P5P-ND for Europe

• The power is controlled by an On/Off switch.

• An LED DS9 indicates the presence of a working wall mount supply

JP1 can be used to select either 3.3V or 2.5V for the Device I/O Voltage

JP2 connects AGND to GND for the use of the PLL.

JP3 connects AVDD to VDD for the use of the PLL.

Note: The five pin header next to the power supply connection can also be used to drive power to the board from a lab supply.

Programming Headers A small form programming header, which is suitable to use with both the Flash Pro and Silicon Sculptor II is supplied with the board. The footprint for the large programming header is on the board, but has not been populated.

12

Clock Circuits


When using Flash Pro, use the STAPL(.STP) file to program the device.

Silicon Sculptor II requires the ISP programming adapter module SMPA-ISP-ACTEL-2-KIT, then you can use either the bitstream (.BIT) file or STAPL (.STP) file.

Clock Circuits The evaluation board has two clock circuits, the 40MHz oscillator and the manual clock.

40MHz Oscillator

The 40MHz oscillator on the board is connected to JP4. JP4 connects the clock to pin 24 of the devices. Pin 24 is a global input pin.

To use pin 24 for a different clock signal, disconnect JP4.

If you want to use a different Clock Frequency, purchase the Crystal from Epson programmed to a variety of frequencies. The SG-8002JC40.000M-PCC from Epson is also available through Digikey.

Manual Clock When activated, the manual clock button (PB1) lights DS10 the pulse generated LED and generates a pulse. This is connected to JP17. JP17 connects to pin 128 of the device. Pin 128 is a global input pin.

If you want to use pin 128 for a different clock signal, disconnect JP17.

LED Device ConnectionsEight LED are connected to the device via jumpers. If the jumpers are in place, the device I/O can drive the LED. The LED changes based on the following output:

• A 1 on the output of the device lights the LED.

• A 0 on the output of the device switches off the LED.

• An unprogrammed or tristated output may show a faintly lit LED

Table 3-1 lists the LED/device connections.

13



If you want to use the device I/O for other purposes, remove the jumpers.

Switches Device ConnectionsFour switches are connected to the device via jumpers. If the jumpers are in place the device I/O can be driven by the following switches:

• Pressing the switch drives a 1 into the device. The 1 continues to drive while you hold the switch.

• Releasing the switch drives a zero into the device.

Table 3-2 lists the switch/device connections.

If you want to use the device I/O for other purposes, remove the jumpers.

Table 3-1. LED Device Connections

LED Device Connection

DS1 87

DS2 90

DS3 91

DS4 92

DS5 93

DS6 94

DS7 95

DS8 96

14

Switches Device Connections


Table 3-2. Switch Device Connections

Switch Device

Connection

SW1 55

SW2 63

SW3 69

SW4 79

15



16


ABoard Connections

This appendix lists a table for board connections.

Table A-1 shows the board connections.

Table A-1. Board Connections

Pin No.APA075

APA150

APA300

APA450

APA600

APA750

APA1000

Board Connect

1 GND GND GND GND GND GND GND GND

2 I/O I/O I/O I/O I/O I/O I/O I/O














16 VDD VDD VDD VDD VDD VDD VDD VDD


17

Appendix A: Board Connections






22 VDDP VDDP VDDP VDDP VDDP VDDP VDDP VDDP


24 GL GL GL GL GL GL GL JP4

25 AGND AGND AGND AGND AGND AGND AGND JP2

26 NPECL NPECL NPECL NPECL NPECL NPECL NPECL NPECL

27 AVDD AVDD AVDD AVDD AVDD AVDD AVDD JP3

28 PPECL(I/P)

PPECL(I/P)

PPECL(I/P)

PPECL(I/P)

PPECL(I/P)

PPECL(I/P)

PPECL(I/P)

PPECL(I/P)


30 GL GL GL GL GL GL GL GL









Pin No.APA075

APA150

APA300

APA450

APA600

APA750

APA1000

Board Connect

18



















55 I/O I/O I/O I/O I/O I/O I/O JP5





Pin No.APA075

APA150

APA300

APA450

APA600

APA750

APA1000

Board Connect

19

























Pin No.APA075

APA150

APA300

APA450

APA600

APA750

APA1000

Board Connect

20
























Pin No.APA075

APA150

APA300

APA450

APA600

APA750

APA1000

Board Connect

21



101 TCK TCK TCK TCK TCK TCK TCK TCK

102 TDI TDI TDI TDI TDI TDI TDI TDI

103 TMS TMS TMS TMS TMS TMS TMS TMS



106 VPP VPP VPP VPP VPP VPP VPP VPP

107 VPN VPN VPN VPN VPN VPN VPN VPN

108 TDO TDO TDO TDO TDO TDO TDO TDO

109 TRST TRST TRST TRST TRST TRST TRST TRST

110 RCK RCK RCK RCK RCK RCK RCK RCK













Pin No.APA075

APA150

APA300

APA450

APA600

APA750

APA1000

Board Connect

22








128 GL GL GL GL GL GL GL JP17

129 PPECL(I/P)

PPECL(I/P)

PPECL(I/P)

PPECL(I/P)

PPECL(I/P)

PPECL(I/P)

PPECL(I/P)

PPECL(I/P)


131 AVDD AVDD AVDD AVDD AVDD AVDD AVDD JP3

132 NPECL NPECL NPECL NPECL NPECL NPECL NPECL NPECL

133 AGND AGND AGND AGND AGND AGND AGND JP2

134 GL GL GL GL GL GL GL GL









Pin No.APA075

APA150

APA300

APA450

APA600

APA750

APA1000

Board Connect

23

























Pin No.APA075

APA150

APA300

APA450

APA600

APA750

APA1000

Board Connect

24
























Pin No.APA075

APA150

APA300

APA450

APA600

APA750

APA1000

Board Connect

25

























Pin No.APA075

APA150

APA300

APA450

APA600

APA750

APA1000

Board Connect

26







Pin No.APA075

APA150

APA300

APA450

APA600

APA750

APA1000

Board Connect

27



28


BBoard Schematics

This appendix shows illustrations of the ProASIC Evaluation Board.

Figure B-1 shows a board schematic.

29

Appendix B: Board Schematics


Figure B-1. Board Schematic

C91 2

C11

1 2

C15

1 2

C10

1 2

C61 2

+3.3v

C71 2

C13

1 2

Good

Power

Enable

InInOut

Out

Gnd

TPS77633PWP

VR1

6 7 5

13 14 16

3

C19

1 2

1.0K

R21

1 2

C17

12

+3.3v

JP21

2

330

R41 2

JP31

2

HDR4

52

C36

1 2

C12

1 2

C51 2

Gnd

Out

V+40.000MHz

Oscillator

Y13

4 2

TP2 4

TP2 5

TP2 1

TP2 2

JP4

12

+3.3v

+3.3v

330

R31 2

220

R21 2

C25

1 2

Global or I/O

VDD(+2.5v)

NPECL1

Analog Gnd

VDDP(2.5/3.3v)

Ground

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

Ground

U11 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

C23

1 2

+2.5v

Global or I/O

Analog Gnd

NPECL2

Ground

VDDP(2.5/3.3v)

I/O

AVDD

VDD(+2.5v)

Ground

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

U1131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

P110

C31 2

C22

1 2

P225

P223

P221

P215

Global or I/O

AVDD(+2.5v)

PPECL1

VDD(+2.5v)

VDDP(2.5/3.3v)

Ground

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

Ground

Ground

U127 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

Ground

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

I/O

I/O

VDD(+2.5v)

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

U1183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

VDD(+2.5v)

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

Ground

U1

53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78

TCK

TDI

TMS

VDD(+2.5v)

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

Ground

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

Ground

U179 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

101

102

103

104

Global or I/O

TRST

PPECL2

RCK

TDO

VPN

VPP

VDD(+2.5v)

VDDP(2.5/3.3v)

Ground

Ground

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

Ground

U1105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

Ground

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

I/O

I/O

VDD(+2.5v)

Ground

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

U1

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

P115

P211

P210

220

R51 2

HDR4

51

HDR4

50

HDR4

49

HDR4

48

HDR4

47

HDR4

46

HDR4

45

HDR4

44

HDR4

43

HDR4

42

HDR4

41

HDR4

40

C81 2

C21

1 2

C27

1 2

C28

1 2

P19

P13

P113

P15

C16

1 2

HDR4

39

HDR4

38

HDR4

37

C24

1 2

P125

P123

P121

P29

P117

P11

HDR4

36

HDR4

35

HDR4

34

HDR4

33

HDR4

32

HDR4

31

HDR4

30

HDR4

27

HDR4

28

HDR4

29

HDR4

26

HDR4

25

HDR4

24

HDR4

23

HDR4

22

HDR4

21

HDR4

20

HDR4

19

HDR4

18

HDR4

17

HDR4

16

HDR4

15

HDR4

14

HDR4

13

HDR4

12

HDR4

11

HDR4

10

HDR4

9

HDR4

8

HDR4

7

HDR4

6

HDR4

5

HDR4

4

HDR4

1

HDR4

2

HDR4

3

HDR3

52

HDR3

51

HDR3

50

C14

1 2

HDR3

49

HDR3

48

HDR3

47

HDR3

46

HDR3

45

HDR3

44

C18

1 2

Good

Power

Enable

InInOut

Out

Gnd

TPS77625PWP

VR2

6 7 5

13 14 16

3

SW2

1 234

C20

1 2

HDR3

43

HDR3

42

HDR3

41

HDR3

40

HDR3

39

HDR3

38

HDR3

37

HDR3

36

HDR3

35

HDR3

34

HDR3

33

HDR3

32

HDR3

31

HDR3

30

HDR3

27

HDR3

28

HDR3

29

HDR3

26

HDR3

25

HDR3

24

HDR3

23

HDR3

22

HDR3

21

HDR3

20

HDR3

19

HDR3

18

HDR3

17

HDR3

16

HDR3

15

HDR3

14

HDR3

13

HDR3

12

HDR3

11

HDR3

10

HDR3

9

HDR3

8

HDR3

7

HDR3

6

HDR3

5

HDR3

4

P126

HDR3

1

HDR3

2

HDR3

3

HDR2

52

HDR2

51

HDR2

50

HDR2

49

HDR2

48

P124

P122

P120

P118

P116

P114

P112

P17

P18

P16

P14

P119

P12

P111

HDR2

47

HDR2

46

C26

1 2

P23

P213

P25

P217

P21

P226

P224

P222

P220

HDR2

45

P218

P216

HDR2

44

HDR2

43

HDR2

42

P214

P212

P27

P28

P26

P24

HDR2

41

HDR2

40

HDR2

39

P219

HDR2

38

HDR2

37

HDR2

36

HDR2

35

HDR2

34

HDR2

33

P22

HDR2

32

HDR2

31

HDR2

30

HDR2

27

HDR2

28

HDR2

29

HDR2

26

HDR2

25

HDR2

24

HDR2

23

HDR2

22

HDR2

21

HDR2

20

HDR2

19

HDR2

18

HDR2

17

HDR2

16

HDR2

15

HDR2

14

HDR2

13

HDR2

12

HDR2

11

HDR2

10

HDR2

9

HDR2

8

HDR2

7

HDR2

6

HDR2

5

HDR2

4

HDR2

1

HDR2

2

HDR2

3

HDR1

52

HDR1

51

HDR1

50

HDR1

49

HDR1

48

HDR1

47

HDR1

46

HDR1

45

HDR1

44

HDR1

43

HDR1

42

HDR1

41

HDR1

40

HDR1

39

HDR1

38

HDR1

37

HDR1

36

HDR1

35

HDR1

34

HDR1

33

HDR1

32

HDR1

31

HDR1

30

HDR1

27

HDR1

28

HDR1

29

HDR1

26

HDR1

25

HDR1

24

HDR1

23

HDR1

22

HDR1

21

HDR1

20

HDR1

19

HDR1

18

HDR1

17

HDR1

16

HDR1

15

HDR1

14

HDR1

13

HDR1

12

HDR1

11

HDR1

10

HDR1

9

HDR1

8

HDR1

7

HDR1

6

HDR1

5

HDR1

4

HDR1

1

HDR1

2

HDR1

3

1.0K

R11

1 2

C11 2

C21 2

OnSW5

12

345

6

JP16

12JP

151

2JP14

12JP

131

2JP12

12

3 21DC

JP11

12

JP1 2 13

DS9

12

330

R11 2

JP91

2

1.0K

R22

1 2

MMBT2222

Q1

3 2

12.0K

R7 12

2.0K

R81 2

150

R10

1 2

+5v

+3.3v

+5v

RC

Q Q

CLR

74LV123A

U2

5 12910

11

67

+3.3v

+3.3v

220K

R9 12

18K

R6 12

C32

12C3

51 2

1000

pF

C30

12

C29

1 2

JP10

12

JP5

12

TP2 3

150

R19

1 2

DS1

12DS2

12DS3

12DS4

12DS5

12DS6

12DS7

12DS8

12

150

R17

1 2150

R18

1 2150

R16

1 2150

R15

1 2150

R13

1 2150

R14

1 2150

R12

1 2

+3.3v

Ground

74LV123A

U2

16 8

+3.3v

JP17

12

C31

1 2

JP8

12

JP6

12

JP7

12

RC

Q Q

CLR

74LV123A

U2

13 412

3

1415

PB1

1 234

1.0K

R20

1 2

330

R26

12

DS10

12

C33

1 2

+3.3v

SW4

1 234

1.0K

R23

1 2C4

1 2

C34

1 2

330

R24

12

SW3

1 234

SW1

1 234

330

R25

12

330

R28

12

330

R27

12

C37

1 2

GL-1

28

RCK

TRST

B

TDO

VPN

VPP

TMS

TDI

TCK

U1-9

4

U1-9

5

U1-9

2

U1-9

3

U1-9

0

U1-9

1

U1-8

7

U1-6

9

U1-6

3

U1-5

5

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

U1-9

6

U1-7

9

9V-I

N

EXT-

IN

EXT-

IN

AGND

AGND

AVDD

AVDD

VDDP

VDDP

VDDP

+2.5

V

+2.5

V

+2.5

V

+3.3

V

+3.3

V

+3.3

V

+3.3

V

+3.3

V

+3.3

V

+3.3

V

+3.3

V

+3.3

V

10-6

-02

APAx

xx-2

Rev

.1.0

Assy

.#AP

Axxx

-503

Rev

.A

To FPGA Pin 96

To FPGA Pin 94

To FPGA Pin 92

To FPGA Pin 90

To FPGA Pin 87

VDD

VDD

VDPP

VDPP

VDD (+2.5v)

VDD

VDD

VDDP

VDDP

IMPORTANT:

Equal +3.3v OR +2.5v

Install A Jumper At

JP1 To Select VDDP

VDDP

VDDP

VDDP

Ground

+2.5v

6-8VDC

To FPGA Pin 79

To FPGA Pin 69

To FPGA Pin 63

To FPGA Pin 55

To FPGA Pin 95

To FPGA Pin 93

To FPGA Pin 91

To FPGA Pin 128

220

Input To Pin 30

Press For Clock

1

Install Jumper To

Manual Clock Input

DC Supply

External

Connect To FPGA I/O

APAx

xx-2

.Sch

Augu

st 9

, 20

02

stalled at the factory

R5 and R6 are not in-

Note:

To U1 Pin 24 (Global

Input) and HDR1 Pin 24

GL GL

GND

GND

GND

AGND

GL

GND

GND

GND

GND

GNDGL

TRST

GND

GND

GND

GND

GND

GND

GND

AGNDGND

P1 P2

P1P1P2

P2

HDR4

HDR4

HDR3

HDR3

HDR2

HDR2

HDR1

HDR1

Ana.+2.5v

Ana.Gnd

AGND

AVDD

AVDD(+2.5v)

TRSTB

RCK

TMS

TDO

TDI

TCK

VPN

VPP

No Connection

From

Programmer

TRSTB

RCK

TMS

TDO

TDI

TCK

Ground

Ground

Ground

Ground

Ground

GroundVPN

VPP

PPECL2

NPECL2

AVDDRCK

TDO

VPN

VPP

TMS

TDI

TCK

PPECL1

NPECL1I/O

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

VDDP(2.5/3.3v)

VDD(+2.5v)

VDD(+2.5v)

VDD(+2.5v)

VDD(+2.5v)

VDD(+2.5v)

VDD(+2.5v)

VDD(+2.5v)

VDD(+2.5v)

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

+2.5v

Demo

nstr

atio

n Bo

ard

Northridge, CA 91326

Electronics

RAST

URNo Connection

From

Programmer

TRSTB

RCK

TMS

TDO

TDI

TCK

Ground

Ground

Ground

Ground

Ground

GroundVPN

VPP

Sche

mati

c Di

agra

m-Dr

awin

g Nu

mber

:

PWB

Numb

er:

R.A.

Stur

laDr

awn

By:

Date

:

OfSh

eet

#Re

vise

d:

II

4321

4321

HG

FE

DC

BA

HG

FE

DC

BA

11

30


Figure B-2 shows a schematic of the ProASICPLUS Evaluation Board.

Figure B-2. ProASIC PLUS Evaluation Board

Figure B-3 shows a board schematic.

31



Figure B-3. Board Schematic

32


33



34


CProduct Support

Actel backs its products with various support services including Customer Service, a Customer Technical Support Center, a web site, an FTP site, electronic mail, and worldwide sales offices. This appendix contains information about contacting Actel and using these support services.

Actel U.S. Toll-Free LineUse the Actel toll-free line to contact Actel for sales information, technical support, requests for literature, Customer Service, investor information, and using the Action Facts service.

The Actel toll-free line is (888) 99-ACTEL.

Customer ServiceContact Customer Service for non-technical product support, such as product pricing, product upgrades, update information, order status, and authorization.

From Northeast and North Central U.S.A., call (408) 522-4480 From Southeast and Southwest U.S.A., call (408) 522-4480 From South Central U.S.A., call (408) 522-4434 From Northwest U.S.A., call (408) 522-4434 From Canada, call (408) 522-4480 From Europe, call (408) 522-4252 or +44 (0) 1276 401500 From Japan, call (408) 522-4743 From the rest of the world, call (408) 522-4743 Fax, from anywhere in the world (408) 522-8044

Actel Customer Technical Support CenterActel staffs its Customer Technical Support Center with highly skilled engineers who can help answer your hardware, software, and design questions. The Customer Technical Support Center spends a great deal of time creating application notes and answers to FAQs. So, before you contact us, please visit our online resources. It is very likely we have already answered your questions.

35

Appendix C: Product Support


Guru Automated Technical SupportGuru is a web-based automated technical support system accessible through the Actel home page (http://www.actel.com/guru/). Guru provides answers to technical questions about Actel products. Many answers include diagrams, illustrations, and links to other resources on the Actel web site.

WebsiteActel has a World Wide Web home page where you can browse a variety of technical and non-technical information. The URL is http://www.actel.com.

Contacting the Customer Technical Support CenterHighly skilled engineers staff the Technical Support Center from 7:00 A.M. to 6:00 P.M., Pacific Time, Monday through Friday. Several ways of contacting the Center follow:

Electronic Mail You can communicate your technical questions to our e-mail address and receive answers back by e-mail, fax, or phone. Also, if you have design problems, you can e-mail your design files to receive assistance. We constantly monitor the e-mail account throughout the day. When sending your request to us, please be sure to include your full name, company name, and your contact information for efficient processing of your request.

The technical support e-mail address is [email protected].

36

Contacting the Customer Technical Support Center


Telephone Our Technical Support Center answers all calls. The center retrieves information, such as your name, company name, phone number and your question, and then issues a case number. The Center then forwards the information to a queue where the first available application engineer receives the data and returns your call. The phone hours are from 7:00 A.M. to 6:00 P.M., Pacific Time, Monday through Friday. The Technical Support numbers are:

(408) 522-4460(800) 262-1060

Customers needing assistance outside the US time zones can either contact technical support via email ([email protected]) or contact a local sales office. Please see our list of Worldwide Sales Offices.

37

Appendix C: Product Support


Worldwide Sales Offices

HeadquartersActel Corporation 955 East Arques Avenue Sunnyvale, California 94086 Toll Free: 888.99.ACTELTel: 408.739.1010 Fax: 408.739.1540

US Sales Offices

California

Bay AreaTel: 408.328.2200Fax: 408.328.2358

IrvineTel: 949.727.0470Fax: 949.727.0476

Newbury ParkTel: 805.375.5769Fax: 805.375.5749

Colorado

Tel: 303.420.4335Fax: 303.420.4336

Florida

Tel: 407.977.6846Fax: 407.977.6847

Georgia

Tel: 770.277.4980 Fax: 770.277.5896

Illinois

Tel: 847.259.1501Fax: 847.259.1575

Massachusetts

Tel: 978.244.3800Fax: 978.244.3820

Minnesota

Tel: 651.917.9116Fax: 651.917.9114

New Jersey

Tel: 609.517.0304

North Carolina

Tel: 919.654.4529Fax: 919.674.0055

Pennsylvania

Tel: 215.830.1458Fax: 215.706.0680

Texas

Tel: 972.235.8944Fax: 972.235.9659

International Sales Offices

Canada 235 Stafford Rd. West, Suite 106 Nepean, Ontario K2H9C1, CanadaTel: 613.726.7575 Fax: 613.726.8666

France 361 Avenue General de Gaulle 92147 Clamart CedexTel: +33 (0)1.40.83.11.00 Fax: +33 (0)1.40.94.11.04

Germany Lohweg 27, D-85375 Neufahrn GermanyTel: +49.(0)81.659.584.0 Fax: +49.(0)81.659.584.10

Italy Via dei Garibaldini 5 20019 Settimo Milanese Milano, Italy Tel: +39 (0)2.3809.3259 Fax: +39 (0)2.3809.3260

Japan EXOS Ebisu Building 4F 1-24-14 Ebisu Shibuya-ku Tokyo 150Tel: +81 (0)3.3445.7671 Fax: +81 (0)3.3445.7668Korea30th floor, ASEM Tower, 159-1 Samsung-dong, Kangnam-ku, Seoul, Korea Tel: +82 (0)2.6001.3382 Fax: +82 (0)2.6001.3030

United Kingdom Maxfli Court Riverside Way Camberley, Surrey GU15 3YL United KingdomTel: +44 (0)1276.401450 Fax: +44 (0)1276.401490

38

ProASICPLUS Evaluation Board · APA-EVAL-BRD1 This board contains all the surrounding circuitry,...

Documents

Transcript of ProASICPLUS Evaluation Board · APA-EVAL-BRD1 This board contains all the surrounding circuitry,...