PRISONER TRANSPORT - In-Vehicle Mounting, Tablet-Laptop ...

11
PRISONER TRANSPORT Maximum security for officer and inmate safety Prisoner Transport Insert (KK-S-120-06 shown without ceiling) KWIK-KIT™ PRISONER TRANSPORTS • Solid all-aluminum construction Kwik-Kit will not rust • Available in one, two, three and four compartment floor plans • Every compartment features a 31.75" high x 37.75" wide exit hatch for fast unloading • Keep officers and up to 12 prisoners safe • Transferable for re-use in new vehicles providing a large savings for years of durable service “Slam-Latch” Lexan Cover & Emergency Hatch Grab Straps & Anti-Slide Bench Side & Rear Step Three Compartment Kwit-Kit Dome Light A All Aluminum construction will not rust Heavy Gauge Aluminum (.125) walls and benches withstand prisoner abuse White Powder Finish on Bulkheads improves appearance and visibility in compartment — easier to clean and spot contraband Unique “slam-latch” design automatically locks doors Dome Lights are included to allow officers to see into compartment in preparation for unloading prisoners Lexan/Spit Stopper between driver and prisoner protects officer from prisoner fluids Floor and Ceiling are part of the Kwik-Kit pris- oner transport design which eliminates possible drug stashing locations Emergency Exit Hatches allow for fast unloading in case of accident or fire. Reduces department liability Standard Grab Straps allow rear-cuffed prisoner to hold on during braking Lighter Weight Aluminum instead of steel allows for increased payload and gas mileage savings Compartment Options and aluminum construction increase payload, allowing maximum seating capacity — eliminates multiple trips and number of vans needed Standard Rear Step with non-skid surface included on all models and allows safe entrance/ exit A B C D E F B C D E F FOR MORE VEHICLE APPLICATIONS & MOUNTING ACCESSORIES, CONTACT 1-800-524-9900 OR VISIT WWW.HAVIS.COM

Transcript of PRISONER TRANSPORT - In-Vehicle Mounting, Tablet-Laptop ...


PRISONER TRANSPORT Maximum security for officer and inmate safety

Prisoner Transport Insert (KK-S-120-06 shown

without ceiling)

KWIK-KIT™ PRISONER TRANSPORTS• Solid all-aluminum construction Kwik-Kit will not rust• Available in one, two, three and four compartment floor plans• Every compartment features a 31.75" high x 37.75" wide exit hatch for fast unloading• Keep officers and up to 12 prisoners safe• Transferable for re-use in new vehicles providing a large savings for years of durable service

“Slam-Latch” Lexan Cover & Emergency Hatch

Grab Straps & Anti-Slide Bench

Side & Rear Step

Three Compartment Kwit-Kit

Dome Light

A

All Aluminum construction will not rust

Heavy Gauge Aluminum (.125) walls and benches withstand prisoner abuse

White Powder Finish on Bulkheads improves appearanceand visibility in compartment — easier to clean and spot contraband

Unique “slam-latch” design automatically locks doors

Dome Lights are included to allow officers to see into compartment in preparation for unloading prisoners

Lexan/Spit Stopper between driver and prisoner protects officer from prisoner fluids

Floor and Ceiling are part of the Kwik-Kit pris-oner transport design which eliminates possible drug stashing locations

Emergency Exit Hatches allow for fast unloading in case of accident or fire. Reduces department liability

Standard Grab Straps allow rear-cuffed prisoner to hold on during braking

Lighter Weight Aluminum instead of steel allows for increased payload and gas mileage savings

Compartment Options and aluminum construction increase payload, allowing maximum seating capacity—eliminates multiple trips and number of vans needed

Standard Rear Step with non-skid surface included on all models and allows safe entrance/exit

A

B

C

D

E

F

B C

D

E F

FOR MORE VEHICLE APPLICATIONS & MOUNTING ACCESSORIES, CONTACT 1-800-524-9900 OR VISIT WWW.HAVIS.COM


Kw

ik-Kits™

PartitionsW

indow G

uardsK

-9 Inserts

By: Havis-Shields

KWIK-KITS™

SEE NEXT PAGE FOR KWIK-KIT™ OPTIONS AND ACCESSORIES

T2

Contact us at:

Ph: 800.524.9900 or 215.957.0720 Fax: 215.957.0729

E-mail: [email protected] Web: www.havis.com

Cargo Van Standard LengthNumber of

Prisoner SeatsNumber of

CompartmentsStorage Area

(behind front seats) Part Number Shipping Weight (with pallets - 150 lbs)

Install Time (estimated)

8 1 28" KK-80-01 700 lbs. 10 hours8 2 28" KK-80-02 900 lbs. 12 hours

10 1 12" KK-100-01 800 lbs. 10 hours10 2 12" KK-100-02 900 lbs. 12 hours8 2 12" KK-100-03 800 lbs. 16 hours8 3 12" KK-100-04 900 lbs. 18 hours

10 2 12" KK-100-05 900 lbs. 17 hours10 3 12" KK-100-06* 1000 lbs. 20 hours10 4 12" KK-100-07 900 lbs. 24 hours

Extended Cargo Van8 1 46" KK-80-01 700 lbs. 10 hours8 2 46" KK-80-02 900 lbs. 12 hours

10 1 30" KK-100-01 800 lbs. 10 hours10 2 30" KK-100-02 900 lbs. 12 hours12 1 14" KK-120-01 800 lbs. 13 hours12 2 14" KK-120-02 900 lbs. 14 hours10 2 14" KK-120-03 900 lbs. 16 hours10 3 14" KK-120-04 900 lbs. 18 hours12 2 n/a KK-120-05 900 lbs 17 hours12 3 14" KK-120-06 1000 lbs. 20 hours

Sprinter Van12 1 n/a KK-S-120-01 800 lbs. 18 hours12 2 n/a KK-S-120-02 900 lbs. 20 hours12 3 n/a KK-S-120-06 1100 lbs. 26 hours

* Part not recommended for Extended Cargo Van


Kw

ik-K

its™

Parti

tions

Win

dow

Gua

rds

K-9

Inse

rts

By: Havis-Shields

KWIK-KITS™

Kwik-Kit Accessories and Options

Part Number Description Est. Install Time

KK-MPTKwik-Kit Meal Pass Through Option

For any Kwik-Kit compartment door

Designed to mount in lower half of compartment door viewing area (window)

Requires cutting out lower perforated aluminum viewing area

Pass through hatch door hinges up providing 8" high x 11" wide opening

Heavy duty slide bolt latch has provision for customer supplied padlock

Can be installed anytime (field upgradable)

White powder coat finish

0.75 hour

KK-STORAGE

Kwik-Kit Locking Under-Bench Storage Option

Designed to be used in 3 or 4 compartment Kwik-Kits (side entry compartment)

Replaces existing vertical bech cover panel located in the side compartment bench only

Storage Door hinges down providing 10" high x 28" wide opening

Enclosed under bench storage space = 12" high x 39.5" wide x 11.5" deep

Uses existing panel mount holes for accurate location

Two tamperproof locks with two keys

Gasket seal to minimize water penetration

White powder coat finish

0.5 hour

KK-F-HVAC-1 Heat/AC Standard Kit for Kwik-Kit Ford 5 hours

KK-FD-HVAC-1 Heat/AC Standard Kit for Kwik-Kit Ford Diesel 5 hours

KK-C-HVAC-1 Heat/AC Standard Kit for Kwik-Kit Chevy 5 hours

KK-S-HVACSprinter* Van Diesel Engine Heat/air conditioning system (23,000 BTU air, 32,000 BTU heat)

*Sprinter kits include underbody condenser7 hours

KK-F-VAK* Ford Van Vent Adapter Kit connects to OEM rear A/C blower 1 hour

KK-C-VAK* Chevrolet Van Vent Adapter Kit connects to OEM rear A/C blower 1 hour

KK-F-MAX-AIR Underbody Condenser air conditioning upgrade. Adapts to KK-F-HVAC to provide better cooling (Ford Gas or Diesel Engine) 3 hours

KK-C-MAX-AIR Underbody Condenser air conditioning upgrade. Adapts to KK-C-HVAC to provide better cooling (Chevrolet Gas Engine) 3 hours

KK-PVENT Power vent (100-CFM roof mounted) 1.5 hours

KK-RLL* Roof load/backup light (for mounting above rear entrance doors) 1 hour

KK-BLT Seat belts (Standard two-point lap belt - each) Included with kit install time

PT-THERM1 Thermometer (Dual Display) .5 hour

PT-INTERCOM 12 volt Intercom System (Listen to rear compartments with push to talk) 1 hour

GO-18-140 First Aid Kit (25 person) .25 hour

GS-00402 Fire Extinguisher (five pound) .25 hour

C-VS-1800-ECO 18" Vehicle Specific Console for '04 - '08 Ford Econoline Van Model E-250/E-350 (see page C18 for more info) .75 hour

C-VS-1800-SAV 18" Vehicle Specific Console for '02 - '08 Chevy Savanna Van Model (see page C18 for more info) .75 hour

C-2411 Consolidator® console 24" long x 9" wide x 10" deep w/13" storage compartment .75 hour

C-SP-3B Consolidator seven-place switch panel (Complete w/ backlighting, fuses, relay, wire harness) 1 hour

PT-VIDEO-1 Prisoner Transport 1 camera video system 3 hours

PT-VIDEO-2 Prisoner Transport 2 camera video system 3 hours

PT-VIDEO-3 Prisoner Transport 3 camera video system 4.5 hours

PT-VIDEO-4 Prisoner Transport 4 camera video system 5 hours

PT-VIDEO-MDVR

Prisoner Transport Mobile Digital Video Recorder Option12-volt event based digital recorder provides the ability to capture a video record from all cameras in the PT-VIDEO systemDesigned specifically for mobile applicationsRecording to Compact Flash Card media for unmatched reliability.12V (positive or negative) five channel configurable multi-event triggered inputs. RE: Ignition, Manual switch, Door switch, Emergency Lights etc…True low cost VCR replacement with no moving parts, no internal fan, no audible noise.Optional integrated GPS position and speed tracking and recording.Back End Software includedIncludes C-EB25-MMT-1P equipment bracket

••••••••

PT-VIDEO-GPSPrisoner Transport Global Positioning System Option

Integrated GPS position and speed tracking and recordingUsed only with PT-VIDEO-MDVR

••

KKM99068 Grab strap (included with Kwik-Kits, deleted if KK-BLT is ordered) 10 minutes

HS-DL Single Exterior Door Lock: Exterior locking bar assembly with a drop forged latch handle and hasp, keyed alike

* = Most popular options

Contact us at:

Ph: 800.524.9900 or 215.957.0720 Fax: 215.957.0729

E-mail: [email protected] Web: www.havis.com T3


Kw

ik-Kits™

PartitionsW

indow G

uardsK

-9 Inserts

• Front partition with emergency exit hatch in top center section of the partition

• Two heavy-duty slide bolts in driver compartment allow for quick removal of hatch• The bottom half of the partition is 12 gauge steel• The top half of the partition is 12 gauge steel with

diamond shape openings• 1/4” lexan covers the top perforated half of the

partition

• Rear partition fits behind last bench seat in a 12 or 15 passenger van

• Emergency exit hatch is located in the top center section of the partition with removable pins or slide-bolts accessible from the rear cargo area

• The bottom half of the partition is 12 gauge steel

• The top half is 12 gauge perforated 12 gauge steel

• Middle partition fits behind the first row passenger bench

• The partition wraps around the bench seat to allow for passengers access to the rearward bench seats

• The bottom half of the partition is 12 gauge steel• The top half of the partition diamond shape

openings• There is not an emergency exit hatch in the

middle partition

• Quickly convert your full-size passenger van into a prisoner transport• Fits the van contour from floor to ceiling• Designed for Ford and Chevrolet Vans• 12-gauge formed and welded steel• Front, middle, and rear partitions available• Each partition is 75 lbs.

By: Havis-Shields

PARTITIONS

Vehicle Make & Model Year Front Partition Part Numbers Middle Partition Part Numbers Rear Partition Part Numbers

Chevrolet/GMC Front* Filler Panel Mtg. Kit* Middle Filler Panel Mtg. Kit* Rear Filler Panel Mtg. Kit*

Express/Savana G Van12 or 15 pass/dual side doors

2003-2008 P-FRONT-1 P-MFK-1 P-MID-1 P-MFK-5 P-REAR-1 P-MFK-9

Express/Savana G Van12 or 15 pass/sliding side doors

2003-2008 P-FRONT-2 P-MFK-3 P-MID-1 P-MFK-5 P-REAR-1 P-MFK-9

G Cargo VanDual side doors - no trim

2003-2008 P-FRONT-1 P-MFK-1 P-MID-1 Not Needed P-REAR-1 P-MFK-9

G Cargo VanSliding side door - no trim

2003-2008 P-FRONT-2 P-MFK-3 P-MID-1 Not Needed P-REAR-1 P-MFK-9

Ford

E Series Van12 or 15 pass/dual side doors

2003-2008 P-FRONT-1 P-MFK-2 P-MID-1 P-MFK-6 P-REAR-2 Not Needed

E Series Van12 or 15 pass/sliding side doors

2003-2008 P-FRONT-1 P-MFK-2 P-MID-1 P-MFK-6 P-REAR-2 Not Needed

* Filler panel mounting kits must be ordered along with P-FRONT-1 and P-FRONT-2, P-MID-1, and P-REAR-1 (except where noted they are not needed)Contact Factory for Newer Model Years

T4

Contact us at:

Ph: 800.524.9900 or 215.957.0720 Fax: 215.957.0729

E-mail: [email protected] Web: www.havis.com

VAN PARTITIONS Custom built, high security transport partitions


Kw

ik-K

its™

Parti

tions

Win

dow

Gua

rds

K-9

Inse

rts

Interior Window Guards

Effective, Strong and Discreet way to protect windows

Automated Fabrication Process ensures precise contour fit for easy, clean-looking installation

CNC Punched from one-piece heavy-duty steel for optimum strength and less sharp than expanded (some models available in aluminum)

Diamond-Shaped Perforations allow for increased driver visibility

Black Polyester Powder Coat on all parts for a long-lasting finish

Van window guards (WGI-C1 – C4 & WGI-F1 – F4) come standard with tamper proof hardware and (2) T-25 TORX 1/4" Hex Insert screw driver tips.

Window Bars - Ford Crown Victoria only (WBI-F7)

WINDOW GUARDS Easily enhance prisoner transport security

• Engineered for precise fit and easy installation• Laser cut for each year, make, and model vehicle• Designed for perfect contour fit • No cutting, welding or painting required

By: Havis-Shields

INTERIOR WINDOW GUARDS

Vehicle Make & Model Year Part Number Number of Windows Install Time Weight

Chevrolet/GMC

Express/Savana G Van15 pass/dual side passenger doors

1997-2008 WGI-C1 8 8 hours 90 lbs.

Express/Savana G Van15 pass/sliding side door

1997-2008 WGI-C2 7 8 hours 90 lbs.

Express/Savana G Van12 pass/dual side passenger doors

1997-2008 WGI-C3 7 7 hours 77 lbs.

Express/Savana G Van12 pass/sliding side door

1997-2008 WGI-C4 6 7 hours 77 lbs.

Safari/AstrovanSwing out rear door

1997-2005 WGI-C5 6 6 hours 52 lbs.

Safari/AstrovanRear dutch door w/ hatch

1997-2005 WGI-C6 5 6 hours 52 lbs

G Cargo VanDual side doors - no trim

1997-2008 WGI-C10 4 1 hour 36 lbs.

G Cargo VanSliding side door - no trim

1997-2008 WGI-C11 3 1 hour 36 lbs.

NOTE 1. Most sedans & SUV’S available with hinge kit (PART # WGI-HK) for folding down rear passenger window

HAVIS-SHIELDS INTERIOR WINDOW GUARDS are designed specifically for each make and model of vehicle listed above. The guards are designed to fit to the interior windowpanels modified and replaced.

Contact us at:

Ph: 800.524.9900 or 215.957.0720 Fax: 215.957.0729

E-mail: [email protected] Web: www.havis.com T5


Kw

ik-Kits™

PartitionsW

indow G

uardsK

-9 Inserts

By: Havis-Shields

Vehicle Make & Model Year Part Number Number of Windows Install Time Weight

Chevrolet/GMC (continued)see note 1 Impala 2000-2005 WGI-C12 2 1/2 hour 15 lbs.

see note 1 Impala 2006-2008 WGI-C19 2 1/2 hour 15 lbs.

see note 1Suburban & Yukon XLDouble rear door

2000-2008 WGI-C13 2 1/2 hour 15 lbs.

see note 1Tahoe Yukon 4 doorDouble rear door

2000-2006 WGI-C14 2 1/2 hour 15 lbs.

Tahoe/Yukon 2007-2008 WGI-C20 2 1/2 hour 15 lbs.

see note 1Blazer S10 4 doorSide doors only

1997-2003 WGI-C15 2 1/2 hour 15 lbs.

see note 1Trail Blazer 4 door Side doors only

2002-2008 WGI-C16 2 1/2 hour 15 lbs.

DaimlerChryslersee note 1 Charger 2006-2008 WGI-D23 2 1/2 hour 15 lbs.

see note 1 Durango 4 door 1998-2003 WGI-D14 2 1/2 hour 15 lbs.

see note 1 Durango 4 door 2004-2008 WGI-D21 2 1/2 hour 15 lbs.

see note 1 Magnum 2005-2008 WGI-D22 2 1/2 hour 15 lbs.

Ford

Most PopularE-Series Van15 pass/dual side doors

1994-2008 WGI-F1 9 7 hours 90 lbs.

E-Series Van15 pass/sliding side doors

1994-2008 WGI-F2 8 7 hours 90 lbs.

Most PopularE-Series Van12 pass/dual side doors

1994-2008 WGI-F3 7 6 hours 77 lbs.

E-Series Van12 pass/sliding side doors

1994-2008 WGI-F4 6 6 hours 90 lbs.

see note 1 Expedition 1997-2008 WGI-F14 2 1/2 hour 15 lbs.

see note 1 Explorer 4 door 2002-2008 WGI-F13 2 1/2 hour 15 lbs.

see note 1 Crown Vic Sedan 1998-2008 WGI-F7 2 1/2 hour 15 lbs.

Window Bars (see below)

Crown Vic Sedan 1998-2008 WBI-F7 2 10 minutes 20 lbs.

Taurus Sedan 1998-2006 WGI-F8 2 1/2 hour 15 lbs.

see note 1 Excursion 2000-2006 WGI-F12 2 1/2 hour 15 lbs.

F-250, 350, 450, 550 Pickup Crew Cab 2006-2007 WGI-F15 2 1/2 hour 15 lbs.

NOTE 1. Most sedans & SUV’S available with hinge kit (PART # WGI-HK) for folding down rear passenger windowHAVIS-SHIELDS INTERIOR WINDOW GUARDS are designed specifically for each make and model of vehicle listed above. The guards are designed to fit to the interior windowpanels modified and replaced.

INTERIOR WINDOW GUARDS

Interior Window Bars for 1998-2008 Crown VicDesigned to make windows easy to clean and allow greater visibility for the driverInstalls in less than 10 minutesEach window has own window barManufactured from #12 gauge steel and 3/8" steel rods and finished with black polyester powder coatOnly works with OEM (Ford) padded interior door panels

••••

WBI-F7

T6

Contact us at:

Ph: 800.524.9900 or 215.957.0720 Fax: 215.957.0729

E-mail: [email protected] Web: www.havis.com


Kw

ik-K

its™

Parti

tions

Win

dow

Gua

rds

K-9

Inse

rts

By: Havis-Shields

DOOR PANELS & VAN STEPS

ALUMINUM DOOR PANELS

Makes doors safer for handling prisoners and dogsCan’t access lock mechanism or damage OEM door panelWhite powder coat finishEasy to install and cleanCut and formed to fit with mounting holesRemove OEM door panels and install smooth .062 aluminum panelsHardware included

Available for:12 and 15 passenger vans with double swing out side and rear doors (4 per kit)Sedan and SUV rear side passenger doors (2 per kit)Individual door panels can be purchased separatelyDoor panels made to accept Havis-Shields hinged window guardsWindow guards sold separately

•••

••••

Provides safe entry and exit of vanHeavy duty steel framework and non slip tread surfaceBlack powder coat finish

•••

Bolt-on design for simple installation (some drilling required)Available for side or rear doors on Chevy, Ford and Sprinter passenger vans

••

SIDE SLIDE OUT STEPSide slide out step tread (SS) is 30" wide by 10" deepEasy to use with no mechanical partsShipping weight: 45 lbs.

••

REAR PERMANENT STEPRear permanent step (RP) tread is 48" wide by 10" deepOptional flip down 2nd step bolts to standard rear step and is designed to help prisoners with leg shackles (48" wide x 10" deep)Flip down step is easy for operator to open and close; slam latch keeps it in the stored position

Shipping weight: 45 lbs. (75 lbs. with flip down option)

Make & Model Year Qty. in Kit Kit Part No

Chevrolet/GMC

Express/Savana G Van 1997-2008 4 DP-C1-A

G Cargo Van 1997-2008 4 DP-C10-A

Impala 2000-2005 2 DP-C12-A

Impala 2006-2008 2 DP-C19-A

Suburban & Yukon XL 2000-2008 2 DP-C13-A

Tahoe & Yukon 4 door 2000-2008 2 DP-C14-A

Blazer S10 4 door 1997-2003 2 DP-C15-A

Trailblazer 2002-2008 2 DP-C16-A

Ford

E Series Van 1994-2008 4 DP-F1-A

Crown Vic Sedan 1998-2008 2 DP-F7-A

Excursion 2000-2006 2 DP-F12-A

Explorer 2002-2008 2 DP-F13-A

Expedition 1997-2008 2 DP-F5-A

F-250, 350, 450, 550 Pick-Up Crew Cab 2006-2007 2 DP-F15-A

Dodge

Charger 2006-2008 2 DP-D23-A

Durango 1998-2003 2 DP-D14-A

Durango 2004-2008 2 DP-D21-A

Magnum 2005-2008 2 DP-D22-A

Side Step

Rear Step

Rear Flip Step

VAN STEPS

Make & Model Year Description Part Number

Chevy Vans 1997-2008 Side Step Assembly KK-C-ST-SS

Ford Vans 1997-2008 Side Step Assembly KK-F-ST-SS

Sprinter Vans 2003-2007 Side Step Assembly KK-S-ST-SS

Chevy Vans 1997-2008 Rear Permanent Step Assembly KK-C-ST-RP

Ford Vans 1997-2008 Rear Permanent Step Assembly KK-F-ST-RP

Sprinter Vans 2003-2007 Rear Permanent Step Assembly KK-S-ST-RP

Flip Down Step Option (order with KK-x-ST-RP)(shown to left- flipped up and down)

KK-ST-FLIP

Contact us at:

Ph: 800.524.9900 or 215.957.0720 Fax: 215.957.0729

E-mail: [email protected] Web: www.havis.com T7


Kw

ik-Kits™

PartitionsW

indow G

uardsK

-9 Inserts

• Unique white powder coat finish• Easy to install• Radius corners, molded edges and proper sized ventilation holes• Fabricated from heavy-duty aluminum for long-lasting durability• Designed to maximize officer room and visibility

K9 TRANSPORT SYSTEMS FOR SEDANS• Includes Single Compartment Kit with one sliding front door and aluminum fold-down interior window

guards and door panels • Custom Black Molded Trim eliminates sharp edges (available on Crown Victoria only)• Entire Rear Passenger Seat area utilized• Rear Guard folds down to allow easy access and cleaning of rear window deck• Sedan Kit Dimensions 27" deep x 59" wide x 35" high

Chevrolet Tahoe K9 & Prisoner Transport (KK-K9-C14-K-PT)

K9 TRANSPORT SYSTEMS FOR SUVS• SUV Kits Housing with one front sliding door, two side door tunnels, aluminum fold-down interior window

guards and door panels• SUV Kit Dimensions

Small SUV Kit: 42" deep x 38" wide x 33" high - For Blazer, Trailblazer, Durango, and Explorer models Large SUV Kit: 48" deep x 47" wide x 34" high - For Suburban, Tahoe, Yukon, Yukon XL, Expedition, and

Excursion models (slide-in center divider available on large SUV kits to create a two-compartment unit for holding two K9’s)

• New 32" Deep SUV Kit 32" deep x 47" wide x 34" high - For Tahoe, Yukon, Suburban, Excursion, & Expedition models

• K9/Prisoner Transport Kits For Tahoe, Yukon, Suburban, and Expedition models. K9 space is on the driver side, prisoner space is on the passenger side

Ford Crown Victoria K9 Unit (KK-K9-F7-K)

Dodge Magnum K9 Transport (KK-K9-D22-K)

By: Havis-Shields

Vehicle Make & Model Year K-9 KitPart Number

32" Deep K-9 KitPart Number

PT/K-9 KitPart Number

Chevrolet/GMC

Impala 2006-2008 KK-K9-C19-K

S-10 Blazer 1998-2003 KK-K9-C15-K

Suburban/Yukon XL 2000-2008 KK-K9-C13-K KK-K9-C13-K-32 KK-K9-C13-K-PT

Trailblazer (5 Passenger/short ONLY) 2002-2008 KK-K9-C16-K

Yukon/Tahoe 4 Door 2000-2006 KK-K9-C14-K KK-K9-C14-K-32 KK-K9-C14-K-PT

Yukon/Tahoe 4 Door 2007-2008 KK-K9-C20-K KK-K9-C20-K-32 KK-K9-C20-K-PT

DaimlerChrysler

Charger 2006-2008 KK-K9-D23-K

Durango 1999-2003 KK-K9-D14-K

Durango 2004-2008 KK-K9-D21-K

Magnum 2005-2008 KK-K9-D22-K

Ford

Crown Victoria Sedan 1998-2008* KK-K9-F7-K

Crown Victoria Sedan with Fire Suppression Option 1998-2008 KK-K9-F7-K-FS

Explorer 4 Door 2002-2007 KK-K9-F13-K

Expedition 2003-2008 KK-K9-F14-K KK-K9-F14-K-32 KK-K9-F14-K-PT

Excursion 2000-2006 KK-K9-F12-K KK-K9-F12-K-32

HAVIS-SHIELDS POLICE CANINE TRANSPORT KITS are a single-compartment module with aluminum side door panels, WGI series interior hinged window guards, rubber matting and dome light with switch. They must be assembled in the vehicle. Installation is quick and easy. *Notes: Available for 2005 to 2006 Crown Victoria without fire suppression option- must specify when ordering

K-9 TRANSPORTATION SYSTEMS

T8

Contact us at:

Ph: 800.524.9900 or 215.957.0720 Fax: 215.957.0729

E-mail: [email protected] Web: www.havis.com

K9 TRANSPORT SYSTEMS Safety and comfort for you and your canine partner


Kw

ik-K

its™

Parti

tions

Win

dow

Gua

rds

K-9

Inse

rts

By: Havis-Shields

K-9 TRANSPORTATION SYSTEMS

K-9 Accessories Part Number Description

KK-K9-WGI-FAN-F7-6-OBROptional Interior window guard for 12" fan to mount in 1998-2008 Passenger Side Crown Vic Sedan with new oblong perforations (KK-K9-HA-FKT-I 12" fan sold separately- see below)

KK-K9-WGI-FAN-F7-1-OBROptional Interior Window Guard for 12" fan to mount in 1998-2008 Driver Side Crown Vic Sedan with new oblong perforations (KK-K9-HA-FKT-I 12" Fan sold separately- see below)

KK-K9-FAN Fan mounted on ceiling or front wall to circulate vehicle air conditioning (4" x 4" 95 CFM)

KK-K9-WATER Water container (w/ stainless steel bowl & bracket) Not recommended for sedan units

KK-K9-DIVIDER-2 Divider for large SUV’s only (Easily slides in to create 2 compartment unit)

AceK9.com Door Pop System KK-K9-HA-2510 K9 Heat Alarm Pro includes: S.O.S. horn alert module, dual window drop module,

lightbar activation module, siren activation module, remote pager/beeper module

AceK9.com Door Pop System KK-K9-HP-5010-H

Remote door Hot-N-Pop system including S.O.S. horn alert module, dual window drop module, lightbar activation module, and siren activation module (Heavy duty solenoid for SUV, truck, special applications)

AceK9.com Door Pop System KK-K9-HP-5010-S

Remote door Hot-N-Pop system including S.O.S. horn alert module, dual window drop module, lightbar activation module, siren activation module, Remote Pager/Beeper Module (Standard Duty solenoid for Sedans)

AceK9.com Door Pop System KK-K9-DP-SUV SUV Solenoid Upgrade (required for SUV door)

AceK9.com Door Pop System KK-K9-HA-RBM-I Remote Pager / Beeper Module

AceK9.com Door Pop System KK-K9-HA-FKT-I 12" Fan, 350 CFM activation module, manual switch and materials

(must order KK-K9-HP-5010 to activate this fan)

AceK9.com Door Pop System KK-K9-DP-SDS Solenoid for sedans

(replacement part for the KK-K9-HA-5000 Hot-N-Pop Pro remote door opener)

AceK9.com Door Pop System KK-K9-DP-SSK Gas Shock for both sedans and SUV’s

(replacement part for the KK-K9-HA-5000 Hot-N-Pop Pro remote door opener)

Hot-N-Pop System control (shown mounted in a C-EB35-RHP-1P equipment bracket)

Water Container for SUV's(KK-K9-WATER)

K9 Transport Options and Accessories

Air Circulation Fan(KK-K9-FAN)

KK-K9-HA-FKT-I mounted on KK-K9-WGI-FAN-F7-1-OBR

High Volume Heat Alarm Fans (KK-K9-HA-FKT-I)

Hot-N-Pop Heat Sensor and Door Pop System

Contact us at:

Ph: 800.524.9900 or 215.957.0720 Fax: 215.957.0729

E-mail: [email protected] Web: www.havis.com T9


TRANSPORT PRODUCTSBy: Havis-Shields

Choosing the Correct Prisoner Transport SystemUse these questions as a guideline to help determine the size and scope of prisoner transport unit. When you are ready to speak with one of our sales representatives, you will have all the necessary information you need to get started!

Year, Make and Model of van? Cargo or Window van?Standard or Extended length Van?What is Van GVWR? (Minimum 8650 recommended)Does vehicle have factory (OEM) rear heat/air conditioning?Does van have rear or side door window glass?Does van have side sliding or double swing out doors? (swing out recommended)How many prisoners do you wish to carry? (Seat spacing per person is 18" to 20")How many separate compartments are required?Is storage space needed for prisoner personal belongings and/or Law Enforcement equipment?What special features are you considering? (Seat belts, rear load light, control console, ect.) (See accessories page T3)Do you require installation to be supplied by a Havis-Shields Authorized Service center?

Havis-Shields always recommends these options for Kwik-Kits:

• Rear air conditioning/heat (see page T3 for more info) • Roof power vent (Part # KK-PVENT)

• Rear load/backup light (Part # KK-RLL) • OEM rear door window glass and side door window glass when side compartment is used

Havis-Shields maintains a full service installation facility. We sell and install the leading brands of emergency lighting and accessories. We can also install of customer supplied equipment.

1.2.3.4.5.6.7.8.9.10.11.

12.

T10

Contact us at:

Ph: 800.524.9900 or 215.957.0720 Fax: 215.957.0729

E-mail: [email protected] Web: www.havis.com


By: Havis-Shields

TRANSPORT PRODUCTS

Havis-Shields Prisoner Transport Vehicle Worksheet

Please supply the following information to ensure that the proper equipment is provided for your transport vehicle. This is necessary to determine the exact products for pricing and placing orders.Note: Some of these items may not apply to your specific vehicle.

Make of Vehicle: ________________________ Year: ______________ Model of Vehicle: _________________

Van Type: Cargo Window Number of Windows (behind driver’s seat):

Length: Standard Extended Wheel Base:

How many bench seats? 0 1 2 3 4 Gas Diesel

Van GVWR: _______________ (minimum 8650 recommended)

Payload/Model: 150/1500 250/2500 350/3500 (minimum 250/2500 recommended)

Factory (OEM) rear heat/air-conditioning: Yes No (Special applications may apply for OEM rear system)

Door Window Glass: Rear- Yes No Side- Yes No

Maximum number of prisoners : _______________ (Seat spacing per person: 18" to 20")

Number of separate compartments required: 1 2 3

Storage space requirement: Personal Law enforcement equipment

Optional equipment: _________________________________________________________________________(Seat belts, power vent, control console, ect.)

Installation: Havis-Shields Authorized Service center Other

Ship to address: Fork lift available Loading dock available Drop gate delivery required

Name: ________________________________ Date: _________________________________

Title: ________________________________ Department: ___________________________

Company: _____________________________________________________________________

Phone: (______) _________________________ Fax: (______) __________________________

Email address: ___________________________

Ship to: ________________________________

__________________________________________

__________________________________________

Contact us at:

Ph: 800.524.9900 or 215.957.0720 Fax: 215.957.0729

E-mail: [email protected] Web: www.havis.com T11