PRessURe vessel clAmPs · 2017-03-17 · 7 u Ç Avenue Z v } o Z U E: ì ó ì ô ï tel...
Transcript of PRessURe vessel clAmPs · 2017-03-17 · 7 u Ç Avenue Z v } o Z U E: ì ó ì ô ï tel...
7 9ƳŜNJȅ Avenue wŀƴŘƻƭLJƘΣ bW лтлуо
tel 908.688.3600 fax 908.688.6060
PRessURe vessel clAmPsThis quick-release pressure vessel clamp system is the most practical and widely used means of positively securing flanges on pressure vessels in processing plants. The clamps replace conventional swing bolts and typically provide substantial saving over stud bolts on any vessel or processing equipment requiring even occasional opening. A wide range of sizes and types are available, including special versions with limited swing, downward release, reversing swing, etc…
The segmented screw clamp can be modified to fit your processing needs.
sAve TIme AND mONeY
• REDUCE LABOR TIME IN HALF or less as compared with standard nut and bolt • NO DRILLED FLANGES – Closing force acts near vessel wall • LESS Material (Narrower & shallower flange section) • LESS Preparatory Work • LESS Machining (drilling, rolling, etc…) • FEWER closing screw clamps than standard nut and bolt • QUICKER RELEASE with fewer turns of each nut • SAFER – Eliminates dangers created by missing nuts and bolts
TYPIcAl APPlIcATIONs
Reactor Vessels • Pressure Vessels • Vacuum Vessels • Pressurized Filter Housings Mix Vessels • Centrifuges • Manways
This unique screw clamping system is utilized for securing tank covers, manways, port holes, and flange openings without the necessity to drill and tap bolt holes into the flange surfaces, saving material and time in building and assembling these flanges.
The clamps are available with ASME code certification.
execUTION: Drop forged, without cracks and wrinkles. Surface is sandblasted.
Certificate according to DIN EN10204 3.2 and ASME code.
Type Clamping length Length WidthD M L B a b c d e f g h i k l m n
M 10-K 13 - 24 83M 10-L 22 - 33 94M 10-LS 70 - 83 122 - - - -
M 12-L 40 - 56 133 34 4 5 4 8 18 20 16 38 6 8 6 70 30
M 16-K 40 - 60 165M 16-L 55 - 85 192M 16-L2 80 - 110 213M 16-LS 95 - 125 234
M 20-K 50 - 75 195M 20-L 65 - 90 212M 20-L2 90 - 130 252
M 24-K 65 - 95 230M 24-L 90 - 130 265M 24-L2 120 - 160 295M 24-LS 155 - 200 335M 24-LX 290 - 330 470
M 27-K 90 - 110 290M 27 -L 115 - 145 327M 27-L2 150 - 195 375M 27 -L3 205 - 255 435M 27-LS 340 - 385 565M 27-LX 440 - 480 680
M 30-L5 *on request - 63 10 16 8 14 52 45 40 87 9 10 15 155 60
M 33-K 100 - 150 380M 33-L 150 - 200 430M 33-L2 200 - 250 480M 33-L3 250 - 300 530M 33-LX 380 - 430 655M 33-LY 510 - 560 810
M 56-L2 260 - 350 640 115 14 26 10 22 84 65 40 160 17 12 30 310 100M 56 *
205 60
* Clamp size <260 on request!
25 4 4 46
13
10 12
85 9 10
9
1875 14 20 10 24 65 60 48 104
15 155 55
130 46
63 10 16 8 14 52 45 40
34 30 78 10 1252 10 11 8 14 34
73 8 8 10 115 42
92 32
48 10 9 8 14 30 30 30
25 25 58 8 8 840 6 7 5 12 25
Dimensions
275 6
5 43 201215
Weightkg/St.
0.160.180.22
0.50
1.131.211.281.40
1.952.002.20
2.653.003.203.404.80
4.805.005.456.157.709.50
-
9.2010.2010.9011.4013.5016.50
34.00
* Clamp size <260 on request!
- Zinc plating- Pickling and passivating- Electro polishing- Veralit Plating- Hard chroming
MateRial FinisHes aVailable:
- Type W, steel 21CrMo V57, Mat. no. 1.7709, (4125 Equivalent)- Type B7, steel ASTM SA 193-B7 ( SA 193-B17 for larger clamp sizes) (4142 Equivalent)- Type A4, stainless steel, Mat. no. 1.4571, (316Ti Equivalent)- Type B8M, stainless steel ASTM 193-B8M, (316Ti Equivalent)
MateRial aVailable:
tel 908.688.3600 fax 908.688.6060