Pressed Steel

8/11/2019 Pressed Steel

1/17

TECHNICAL PARTICULARS FOR

PRESSED STEEL SHUTTERS AND FRAMES FOR DOORS & WINDOWS .

This Specification lays down the requirements of Pressed Steel Door /

Window Shutters with embossed ribs by means of hydraulic / mechanical power press

and Pressed Steel Frames suitable for Pressed Steel Door Shutters & Window Shutters.Overall sizes of the Pressed Steel Door/Window Shutters & Frames shall be as per the

requirements of the consignee. As such the rates are invited in Rs. per Running

Square Meter

Schedule 1. Shutters suitable for Pressed Steel Door Frames.

1. Shutters made of Single Sheet:

Single Sheet shutters shall be made of CR Sheet with vertically

embossed ribs by means of hydraulic / mechanical power press and are to be

supplied either in Single Panel Shutters or in double Panel Shutters as per the sizerequirements of the consignee. These shutters shall be supplied in the following

types:

a) Single Panel Shutter (Complete Shutter made out of 1.00 mm thick CR

Sheet)

b) Double Panel Shutter (Complete Shutter made out of 1.00 mm thick

CR Sheet)

c) Single Panel Shutter (Complete Shutter made out of 0.80 mm thick CR

Sheet)

d) Double Panel Shutter (Complete Shutter made out of 0.80 mm thickCR Sheet)

e) Single Panel Shutter (Rails of Shutter made out of 1.00 mm thick CRSheet and remaining Shutter made out of 0.80 mm thick CR Sheet)

f) Double Panel Shutter (Rails of Shutter made out of 1.00 mm thick CR

Sheet and remaining Shutter made out of 0.80 mm thick CR Sheet)

2. Shutters made of Double Sheet:

Double Sheet Shutters shall be made of two CR sheets, front sheet

vertically embossed and back sheet horizontally embossed by means of hydraulic /

mechanical power press and are to be supplied either in Single Panel Shutters or indouble Panel Shutters as per the size requirements of the consignee. These shuttersshall be supplied in the following types:

a) Single Panel Shutter (Complete Shutter made out of 1.00 mm thick CR

Sheet)

b) Double Panel Shutter (Complete Shutter made out of 1.00 mm thick

CR Sheet)

c) Single Panel Shutter (Complete Shutter made out of 0.80 mm thick CR

Sheet)d) Double Panel Shutter (Complete Shutter made out of 0.80 mm thick

CR Sheet)


2/17

General requirements and details of profile & accessories for Shutters made ofSingle Sheet / Double Sheet are given in Annexure I.

Schedule 2. Frames for Pressed Steel Door Shutters.

Pressed Steel Door Frames shall be manufactured from Cold Rolled Steel

Sheet of 1.25 mm thickness and shall be of the following profiles as per the size

requirements of the consignee:

a) Profile A - 115 X 50 mm

b) Profile B - 100 X 50 mmc)

Profile C - 80 X 50 mm

d) Profile D - 65 X 40 mm

General requirements and details of profiles & accessories for Pressed Steel

Frames are given in Annexure II.

Note: Door Frames can also be supplied with Mullion Sections/Fan light as per the

requirements of the consignee. Tenderers may also quote rates for Door Frames withMullion Sections/Fanlight. Tenderers shall obtain an approved drawing from the

Indentor before commencing bulk production.

Schedule 3. Frames for Pressed Steel Window Shutters / Ventilators:

Pressed Steel Window Frames shall be manufactured from Cold Rolled Steel

Sheet of 1.25 mm thickness and shall be of the following profiles as per the size

requirements of the consignee:

a) Profile D - 65 X 40 mmb)

Profile E - 115 X 40 mm

General Requirements:

1. The corners of doorframes shall be welded to form a solid fused welded joint.

2. The process of welding adopted may be flash butt welding or any other

suitable method, which gives desired requirements.

3.

The outer frame shall be made from Profile D and Profile E shall be used

between the two panels.

4. Proper provision shall be made for Tower Bolt.

5.

Two Nos. of ISI marked hinges of size 75 mm long shall be fixed on eachvertical side.

6.

Three Nos. of fixing lugs made from 18 X 3 X 150 mm M.S. Sheet shall be

welded on each vertical side of the doorframe at equidistance. The lugs shall

be split for 100 mm at the end.

7. Window Frames with Mullion Sections/Fan light as per the requirements of

the consignee can also be supplied. Tenderers may also quote rates for

Window Frames with Mullion Sections/Fanlight. Tenderers shall obtain an

approved drawing from the Indentor before commencing bulk production.

8. Window Frames may also be supplied with window safety bars as desired bythe consignee. The safety bars shall be of 12 mm dia M.S. Round Bars or of

10 mm M.S. Square bars and they shall be fixed horizontally or vertically withcentre to centre distance not more than 100 mm, as per the requirements of the

consignee. Tenderers may quote rates separately for Window Frames with

safety bars / without safety bars


3/17

Schedule 4. Pressed Steel Shutters for Windows / Ventilators.

Shutters shall be made of CR Sheet of 0.8 mm thickness. The shutters may be

in two panels / three panels as per the size requirements of the consignee.

1. Maximum distance between two vertical ribs shall be 150

mm centre to centre.2.

Minimum depth of ribs shall be 10 mm and width of rib

between 10 to 15 mm.

3. Width of styles and rails shall be 75 mm.4.

One Tower Bolt of 8 X 100 mm shall be provided.

5. Chrome Plated Steel handles of 100 mm size shall be

riveted / bolted on each shutter.

SCHEDULE 5 STEEL FLUSH DOOR

Providing and fixing in position factory made (on precision machines) Steel Flush

Doors, with brand name duty marked on it or equivalent, complete with frame, shutterand required hard wares. The frame and shutter are made out of Galvanized Steel

Sheets. The frame is hallow metal pressed profile as per IS: 4351/2003 with up-to-date amendments - size - 80 x 50 mm - 1.25 mm thickness. The Door Shutter, 35 mm

thick, is fabricated from 1.0 mm thick Galvanized Steel Sheets. It is fully flush,

double skin door with lock seam joints at the style edges. Internal reinforcements are

provided at the top, bottom and style edges. A specially designed resin bonded Craft

paper Honey Comb structure is provided as an infill for the door shutter to give

additional rigidity and effective acoustic and thermal insulation.

Providing 6 no. free hanging holdfast 25 x 3 mm - 150 mm long embedded in cementconcrete blocks - 15 x 10 x 10 cm - size of 1:3:6 cement concrete with 20 mm graded

metal of nominal size. The door frame bottom is tied with 2 nos. 25 x 25x 2 mmangles. The door is to be fitted with 2 nos. Aldrops steel chrome plated - 16 x 250 mm,

2 nos. heavy designs steel handles - 150 mm long, 1 no. tower bolt steel chrome

plated - 10 x 200 mm, 3 nos. ISI marked steel anodized hinges - 125 mm. The door is

to cleaned with suitable three-in-one chemical for degreasing, derusting and

phosphating and applied with special coat of PU rust preventive by dip process in the

lower one fit height (to save door from in long run) and than 2 coats of Zinc Chromate

primer on the complete door.


4/17

SCHEDULE 6 Pressed Steel Doors

Providing and fixing in position factory made (on precision machines) Pressed Steel

Doors, with brand name duty marked on it or equivalent, complete with frame, shutterand required hard wares. The frame and shutter are made out of CRCA Steel Sheets

confirming to IS: 513/2008 with up-to-date amendments. The frame is hallow metal

pressed profile as per IS: 4351/2003 with up-to-date amendments, size - 80 x 50 mm -

1.25 mm/ 18 gauge thickness. The Shutter is 32 mm thick, fabricated using 2 sheets of

1.00 mm/ 20 gauge. The front sheet with vertical embossing of size 14 x 14 mm: Pitch

800 mm and back sheet with horizontal embossing of size 14 x 14 mm: Pitch 125 mm,

the complete shutter is to be spot welded in embossed grooves to make it a single

piece strong unit.

Providing 6 no. free hanging holdfast 25 x 3 mm - 150 mm long embedded in cement

concrete blocks - 15 x 10 x 10 cms. - size of 1:3:6 cement concrete with 20 mmgraded metal of nominal size. The door frame bottom is tied with 2 nos. 25 x 25x 3

mm angles. The door is to be fitted with 2 nos. Aldrops steel chrome plated - 14 x 250

mm, 2 nos. heavy designs steel handles - 150 mm long, 1 no. tower bolt steel chromeplated - 10 x 200 mm, 3 nos. ISI marked steel anodized hinges - 125 mm. The door is

to cleaned with suitable three-in-one chemical for degreasing, derusting and

phosphating and applied with special coat of rust preventive by dip process in the

lower 0.5 meter height and than 2 coats of Zinc Chromate primer on the complete

door.


5/17

Schedule - 7 Pressed Steel Doors

Providing and fixing in position factory made (on precision machines) Pressed SteelDoors, with brand name duty marked on it or equivalent, complete with frame, shutter

and required hard wares. The frame and shutter are made out of CRCA Steel Sheetsconfirming to IS: 513/2008 with up-to-date amendments. The frame is hallow metal

pressed profile as per IS: 4351/2003 with up-to-date amendments - size - 80 x 50 mm

- 1.25 mm/ 18 gauge thickness. The Shutter is 32 mm thick Pressed steel shutter madeout of CCRCA Steel sheets 1.00 mm/20 gauge having 100 mm wide vertical styles

and strengthening ribs embossing of size 14 x 14 mm at 80 mm C/C Pitch in between

the vertical style (Full width for the shutter including vertical style must be formed

out of single sheet only). Top and bottom rail of 100 mm width and lock rail of 150

mm with to be welded system between the vertical style to make the shutter thicknessof 32 mm.


concrete blocks - 15 x 10 x 10 cm. - size of 1:3:6 cement concrete with 20 mm graded

metal of nominal size. The door frame bottom is tied with 2 nos. 25 x 25x 3 mm

angles. The door is to be fitted with 2 nos. Aldrops steel chrome plated - 14 x 250 mm,

2 nos. heavy designs steel handles - 150 mm long, 1 no. tower bolt steel chrome

plated - 10 x 200 mm, 3 nos. ISI marked steel anodized hinges - 125 mm. The


6/17

complete door is to cleaned with suitable three-in-one chemical for degreasing,derusting and phosphating and applied with special coat of rust preventive by dip

process in the lower 0.5 meter height and then 2 coats of Zinc Chromate primer on the

complete door.

Schedule - 8 PVC Flush Door complete

Providing and fixing in position equivalent PVC Flush Door complete with steel

frame and required hard wares. The frame is made out of prime quality CRCA Steel

Sheets confirming to IS: 513/2008 with up-to-date amendments. The frame is hallow

metal pressed profile as per general specification of IS: 4351/2003 with up-to-date

amendments - size 65 x 40 mm - 1.25 mm/ 18 gauge thickness. The Shutter is a

single piece PVC panel 22 mm thick with border A section 25 mm thickness.


concrete blocks - 15 x 10x10 cm. - size of 1:3:6 cement concrete with 20 mm graded

metal of nominal size. The door frame is also to filled with cement concrete. The door

frame bottom is also to be tied with 2 nos. 25 x 3 mm angles. The door is to be fitted

with 2 nos. Aldrops steel chrome plated - 12 x 250 mm, 2 handles steel CP 150 mm, 3

hinges ISI marked steel anodized 100 mm. The door frame is chemically cleaned with

suitable three-in-one chemical for degreasing, derusting and phosphoting and applied

with a special coat of rust preventive by dip process the lower 0.5 meter height and

than 2 coats of Zinc Chromate primer on the complete frame.


7/17

Schedule 9 Premium Glazed Pressed Steel Window

Providing and fixing in position window complete with shutter and square bar grills.The frame is to be hallow metal pressed profile as per general specification of IS:

4351/2003 with up-to-date amendments - size - 65 x 40 mm - 1.25 mm/ 18 SWG

thickness. The Shutter is made of tubular profile of size23 x 50 x 1.3 mm having 15

mm vide lips. Steel beading of size 10 x 10 mm with necessary screws to be provided

to hold the glass in position. The safety gill is to be fabricated using 10 mm square

bars - 10 mm centre to centre. The window frame is to be punched - square holes - toaccommodate bars and they are welded at inside of the frame for further strengthening.

Providing minimum 4 nos. free hanging holds fasts - 25 x 3 mm - 150 long embeddedin cement concrete blocks - 15 x 10 x 10 mm size of 1:3:6 cement concrete with 20

mm graded metal of nominal size. The window frame is also to be filled with cement

concrete. The window shutter is to be fitted with 2 heavy box hinges 70 mm on eachshutter and 250 mm long 12 SWG Oxidized steel stay rods on each shutter and also

the steel chrome plated handles 125 mm and tower bolts 10 x 100 mm to be fitted onit.

The complete window is chemically treated with 3-in-1 chemical and the applied 2

coats of Zinc chromate primer and oven baked.


8/17

Schedule 10 Standard Pressed Steel Window

Providing and fixing in position complete with frame, shutter and square bar grills.

The frame and shutter panels are made of prime quality CRCA steel sheets

confirming to IS: 513/2008 with up-to-date amendments. The frame is to be hallowmetal pressed profile as per general specification of IS: 4351/2003 with up-to-date

amendments, size 65 x 40 mm - 1.25 mm/ 18 gauge thickness. The shutter is to be

fabricated using 7FD and T2 hot rolled section as per IS: 7452/1990 with up-to-date

amendments with spot-welded 0.8 mm thick CRCA steel panels having verticalembossed ribs of size 30 x 6 mm for strengthening safety grill is to be fabricated using

10 mm square bars - 100 mm C/C in brick design, with vertical pieces at 200 mm

spacing. The window frame is to be punched - square holes - to accommodate

horizontal bars and they should be welded at inside of the frame for strength purpose.

Provide minimum 4 nos free hanging holdfast - 25 x 3 mm - 150 mm long embedded

in cement concrete blocks - 15 x 10 x 10 cm - size of 1:3:6 cement concrete with 20mm graded metal of nominal size. The window frame is also to be fitted with cement

concrete. The window is to be fitted with 2 boxes hinges - 70 mm on each shutter, and

250 mm long - 12 long oxidized steel stay rods on each shutter and also the standard

design handles to be fitted. The complete window is treated with three-in-one

chemical and than applied 2 coats of Zinc Chromate primer and oven backed.


9/17

SCHEDULE 11 Standard Glazed Shutter Windows

Providing and fixing in position equivalent pressed steel windows, complete with

frame, shutter and square bar grills. The frame is made of CRCA steel sheets

confirming to IS: 513/2008 with up-to-date amendments. The frame is to be hallowmetal pressed profile as per general specification of IS: 4351/2003 with up-to-date

amendments, size 65 x 40 mm - 1.25 mm/ 18 gauge thickness. The shutter frame is tobe fabricated using 7FD and T2 hot rolled sections as per IS: 7452/1990. Safety grill

is to be fabricated using 10 mm square bars - 100 mm C/C in brick design, withvertical pieces at 200 mm spacing. The window frame is to be punched - square holes

- to accommodate horizontal bars and they should be welded at inside of the frame for

strength purpose. Provide minimum 4 nos. free hanging holdfast - 25 x 3 mm - 150

mm long embedded in cement concrete blocks - 15 x 10 x 10 cm - size of 1:3:6

cement concrete with 20 mm graded metal of nominal size. The window frame is also

to be fitted with cement concrete. The window is to be fitted with 2 boxes hinges - 70

mm on each shutter, and 250 mm long - 12 long oxidized steel stay rods on eachshutter and also the standard design handles to be fitted. The complete window istreated with three-in-one chemical and than applied 2 coats of Zinc Chromate primer.


10/17

SCHEDULE 12 Pressed Steel Ventilators

Providing and fixing in position equivalent - complete with frame, luvers and 10 mm

square bars in case of glass luyered ventilators. The frame is to be made up of 50 x 30

mm pressed box - section 1.25 mm/ 18 SWG steel sheets. The Luvers of pressed

design made up of 1.00 mm/ 20 SWG CRCA steel sheets. In case of glass luvers

ventilators 10 mm square bar - 100 mm centre to centre to be provided. The completeventilator is chemically treated with 3-in-1 chemical and then applied 2 coats of Zinc

Chromate primer and oven backed.

Schedule 13 Cub Board Shutter

Providing and fixing in position shutter with frame made prime quality CRCA steel

sheets. Frame out of 1.25 mm thick sheets, size 40 x 40 mm, shutter out of 0.90 mm

thick sheets, with two hinges on each shutter - IS marked - 75 mm in case of frame

height upto 1.5 meters and 3 hinges for bigger sizes. The hinges are screwed on 2 mmthick plate channel base welded to the frame. The door is with three way looking

system includes locking bar of 10 mm diameter of required length and the middle

locking pad operated by the chrome plate handle, provided with 6 lever GODREJ

make cup-board lock provided with 25 x 3 mm - 200 mm long - 6 nos. hold fasts. The


11/17

complete cup-board shutter with frame is chemically treated with 3-in-1 chemical andthen applied 2 coats of Zinc Chromate primer and the 1 coats of GOODLASS

NEROLAC - TA Grey oil paint duty oven backed.

Schedule 14 Steel Door Frame

Providing and fixing in position factory made (on precision machines) with brand

name duty marked on it. The profile is made from prime quality CRCA steel sheets

confirming to IS: 513/2008 with up-to-date amendments and as per generalspecifications of IS: 4351/2003 with up-to-date amendments. The frame is to be

provided with 6 numbers free handing hold fasts 25 x 3 mm - 150 mm long embedded

in cement concrete blocks - 15 x 10 x 10 cm - size of 1:3:6 cement concrete with 20

mm graded metal of nominal size. The door frame is also to be fitted with cement

concrete. The door frame bottom is tied with 2 numbers - 25 x 25 x 3 mm steel angles,

provided with 3 nos. IS marked steel anodized hinges - 125 mm long, having suitable

position for aldrops and tower bolts. The complete door frame is chemically treated

with 3-in-1 chemical and then 2 coats of zinc chromate primer are applied followedby oven backing. The two ft. lower height of the frame duly painted with anti

corrosive paint.


12/17

Schedule 15 PREMIUM STEEL SHUTTER WINDOW

Complete with frame, shutters and square bar grill. The frame and shutters are made

of prime quality of CRCA steel sheets conforming to IS: 513/2008 with up-to-date

amendments. The frame is to be hollow metal pressed profile as per general

specifications of IS: 4351/2003 with up-to-date amendments, size: 80x50 mm, 1.25

mm/ 18 gauge thickness.

The shutters are fabricated like door shutters, 32mm thick. Pressed steel window

shutters having 80 mm wide vertical styles and strengthening ribs embossed of

14x14mm at 60 mm C/C pitch in between the vertical styles (full width of the shutter

including vertical styles must be formed out of single sheet only). Top and bottom rail

of 80 mm width. Welded to the shutter between the vertical styles (using MIG

welding only).

The safety grill is to be fabricated using 10mm square bars- 100 mm center to center.

The window frame is to be punched square holes to accommodate bars and they are

welded at inside of the frame for strength purpose. Provide minimum 4 Nos freehanging hold fasts 25x3 mm-150 mm long embedded in cement concrete blocks

15x10x10 mm size of 1:3:6 cement concrete with 20mm graded metal of nominal size.

The window frame is also to be filled with cement concrete. The window shutter is tobe fitted with 2 Nos. IS marked hinges 100 mm on each shutter and 250 mm long 12

SWG oxidized steel stay rods on each shutter and also the steel chrome plated handles

125 mm and Tower bolts 10x100 mm to be fitted on it.

Technical requirements for Pressed Steel Doors & Windows

1. Mild Steel Sheet, Round Bars, Square Bars and other sections used in the

fabrication shall conform to Grade Fe 410W A of IS: 2062 / 2006 with up-to-

date amendments.

2. CR-sheet used in the fabrication shall conform to IS: 513 /2008 with up-to-

date amendments.

3. Pressed Steel Shutters / Frames for Door / Windows shall be de-rusted, de-

greased & painted with one coat of metal primer.4. Tolerances: Rolling and Cutting Tolerances shall conform to IS: 1852 / 1985

with up-to-date amendments.5.

Visual Examination: The finished products shall be reasonably free from

surface flaws, laminations, rough / jiggered and imperfect edges and otherharmful defects.

6. Marking: The stores shall be marked for the identity of the manufacturer.

7. Test Certificate: At the time of Inspection, the manufacturer shall produce

Test Certificate for the steel used.


13/17


14/17

ANNEXURE I

STEEL DOOR SHUTTER

10 10 Y

XPROFILE OF STYLES,

TOP RAIL, BOTTOM

RAIL & LOCK RAIL.

ALL DIMENSIONS IN MILLIMETERS

NOT TO SCALE

PROFILE X

(MIN)

Y

(MIN)

STYLES 75 25

TOP RAIL 90 25

BOTTOM RAIL 90 25

LOCK RAIL 150 25

BOTTOM

BOTTOM RAIL

STYLES

STYLES

TOP RAIL

BOTTOM RAIL

LOCK RAIL

CRSHEETWITH

VERTICALLY

EMBOSSEDRIBS

GENERAL REQUIREMENTS:1. Maximum distance between

two vertically embossed ribsshall be 95 mm centre to centre

2. Minimum depth of ribs shallbe10 mm & width of ribs shall

be between 10 to 15 mm.3. Minimum width of Styles shall

be 75 mm.4. Minimum width of Top &

Bottom Rails shall be 90 mm.5. Minimum width of Lock Rail

shall be 150 mm.6. Bottom Rail shall be fabricated

in such a manner that watercould not get accumulated in it.

Straight front face width of

Bottom Rail shall be same asmentioned above, i.e., 90 mmminimum. Holes shall be

provided at bottom of shutter todrain out water.

ACCESSORIES:1. One chrome-plated aldrop of

16x300 mm shall beriveted/bolted on one side and

one chrome-plated latch shallbe fitted on another side.

2.

One tower bolt of 8 x 200 mmshall be provided at upper side.

3. Chrome plated steel handles of150 mm size shall be

riveted/bolted on both sides ofshutter.

DETAILS OF SHUTTERS FOR PRESSEDSTEEL DOOR FRAMES & ITS PROFILES

CHHATTISGARH STATE INDUSTRIAL

DEVELOPMENT CORPORATION LTD.


15/17

ANNEXURE II.

PRESSED STEEL DOOR FRAME

PROFILE A

PROFIE B/C/D

ALL DIMENSIONS IN MILLIMETERS

NOT TO SCALE

PROFILE X YA 115+/-2 50+-2

B 100+/-2 50+/-2

C 80+/-2 50+/-2

D 65+/-2 40+/-2

DETAILS OF PRESSED STEEL DOOR

FRAMES & ITS PROFILES

CHHATTISGARH STATE INDUSTRIAL

DEVELOPMENT CORPORATION LTD.

GENERAL REQUIREMENTS:

1. The corners of door frames shall bewelded to form a solid fused

welded joint.

2.

The process of welding adoptedmay be flash butt welding or anyother suitable method which gives

desired requirements.3. All door frames shall be made of

three sides (two vertical sides andone horizontal at top.) One 10 mm

dia round bar shall be welded atbottom to tie up vertical sides to

keep in exact rectangular shapes.4. Proper provision for bolting/locking

the shutters shall be provided in topside of door frame.

5. Proper provision shall be made fortower bolt and aldrop in the frame.

6. 4 Nos. of ISI marked hinges of size125x65x2.12 mm shall be fixed for

single panel door on right side orleft side as per the consignees

requirement and 8 Nos. of ISImarked hinges shall be provided for

double panel door shutter.7. Three Nos. of fixing lugs shall be

welded on each vertical side of thedoor frame at equidistance. The

lugs shall be made from 3.0 mmthick M.S.Sheet of 18 mm width &

175 mm long, bent for 25 mm atone end and split for 100 mm at the

other end.


16/17

RATE ANNEXURE FOR

PRESSED STEEL SHUTTERS AND FRAMES FOR DOORS & WINDOWS .

1. Rate of excise duty ..% extra

2. Rate of S.T. ...% extra4. Delivery Period (for supply order) ..

5 Whether registered with DGS&D / NSIC / DTIC6. Whether holding BIS / ISO Certificate (as per specification)

7. Whether holding T.T.C. (Yes / No)a). Name of Laboratory

b). Date of Issue

c). Validity

8. Rates shall be quoted on F.O.R. Destination basis, excluding Duties & Taxes.

SubItem

Code

Item Description.

Rates on FOR DestinationBasis Excluding ED & ST

in Rs.

Schedule 1

1 Single Panel Shutter (1.0 mm ) Single Sheet

2 Double Panel Shutter (1.0 mm ) Single Sheet

3 Single Panel Shutter (0.8 mm) Single Sheet

4 Double Panel Shutter (0.8 mm) Single Sheet

5 Single Panel Shutter (Rails 1mm, Shutter 0.8 mm ) Single Sheet

6 Double Panel Shutter (Rails 1mm, Shutter 0.8 mm ) Single Sheet

7 Single Panel Shutter (1.0mm ) Double Sheet

8 Double Panel Shutter (1.0mm ) Double Sheet

9 Single Panel Shutter (0.8 mm) Double Sheet

10 Double Panel Shutter (0.8 mm) Double Sheet

Schedule 2.

11 Profile A - 115 X 50 mm12 Profile B - 100 X 50 mm

13 Profile C - 80 X 50 mm

14 Profile D - 65 X 40 mm

15 Profile A - 115 X 50 mm (With Mullion Section )

16 Profile B - 100 X 50 mm (With Mullion Section )

17 Profile C - 80 X 50 mm (With Mullion Section )

18 Profile D - 65 X 40 mm (With Mullion Section )

Schedule 3.

19 Frames for Window Shutters -Single

20 Frames for Window Shutters - Double

21 Frames for Window Shutters - Triple22 Frames for Window Shutters -Single (With Mullion Section )

23 Frames for Window Shutters - Double (With Mullion Section )

24 Frames for Window Shutters - Triple (With Mullion Section )

25 Frames for Window Shutters -Single (With Safety bars )

26 Frames for Window Shutters - Double (With Safety bars )

27 Frames for Window Shutters - Triple (With Safety bars )

28 Frames for Window Shutters -Single (With Mullion Section ) (WithSafety bars )

29 Frames for Window Shutters - Double (With Mullion Section ) (WithSafety bars )

30 Frames for Window Shutters - Triple (With Mullion Section ) (WithSafety bars )

Schedule 4

31 Pressed Steel Shutters for window - Double

32 Pressed Steel Shutters for window - Triple


17/17

Schedule 5

33 Steel Flush Door

Schedule 6

34 Pressed Steel Doors

Schedule 7

35 Pressed Steel Doors

Schedule 8

36 PVC Flush Door Complete

Schedule 9

37 Premium Glazed Pressed Steel Window

Schedule 10

38 Standard Pressed Steel Window

Schedule 11

39 Standard Glazed Shutter Windows

Schedule 12

40 Pressed Steel Ventilators

Schedule 13

41 Cub Board Shutter

Schedule 1442 Steel Door Frame

Schedule 15

43 Premium Steel Shutter Window

Pressed Steel

Documents

Transcript of Pressed Steel