BAMBU STRUCTURE

BAMBU

Structure of fixed awning with tensed fabric

BAMBU

Possible instalation positions

Position pole profiles 15°

Position pole profiles 0°

Position pole profiles 15°, up

profile 5°

Position pole profiles 0°, up

profile 5°

Position pole profiles 15º-0°,

up profile 5°

Position pole profiles 15º-0º, up profile

0º

BAMBU

Position pole profiles 0°

Título presentación

Position pole profiles 0°, up

profile 5°

BAMBU

Position pole profiles 15°

BAMBU

Position pole profiles 15°, up

profile 5°

BAMBU

Position pole profiles15º-0°, up profile 5°

BAMBU

Position pole profiles15º-0º, up profile 0º

BAMBU

BAMBU

Maximum length up profile A = 6m

BAMBU

Maximum pole profile lenght B = 3m

BAMBU

Minimum high to up profile D = 2,1 m

BAMBU

Minimum distance between pole C = 2 m

BAMBU

Maximum distance between pole E = 3,282 m

BAMBU

FABRIC

BAMBU

Polyester • 2 sides PVC • Drive strength (Warp/Weft): 270 daN - 5 cm / 230 daN - 5 cm • Temperature resistance: -30 +70º • Fire-resistant M2

FABRIC RECOMMENDATION:

BAMBU

1. Pole profile2. Up profile3. Profile joint kit4. Pole base joint5. Pole support6. Pole cap7. Fabric tension kit8. Structural profile

90x509. Concrete slab

BAMBU

1. Pole profile and 2. Up profile

Weight = 5.556 Kg/m

BAMBU

3. Profile joint kit

BAMBU

4. Pole base joint

BAMBU

5. Pole support

BAMBU

6. Pole cap

BAMBU

7. Fabric tension kit

BAMBU

8. Structural profile 90x50

BAMBU

9. Concrete slab

BAMBU

INSTALLATION: part 1 pre-assembling

BAMBU

Thread the holes in thepole and up profiles:

• Poles: in one side the central hole (M12) and the 4 external ones (M8). On

the other side, the central hole (M12)

• Up profiles: only the central hole (M12), at

both sides

BAMBU

Pole base joint assembly:

• Place the joint support in the pole profile.

• Fix both parts with the provided screws.

Note: follow this procedure for the four poles.

Pre-installing the profile joint kits depending on the chosen

assembly option:

• 15º-0º for poles and 5º-0º for up profiles

BAMBU

BAMBU

• Placing the fabric at the up profiles:

• Put the flanges as shown at the image.

• Place the fabric through the ogives at the upper part of the

crossbeam.

BAMBU

• Put the caps at the up profiles

• Screw down the caps at up profiles

Fabric tensor kit assembly:

• Coil the prisoners to the piece and align as shown at the image

• Put and screw to the profile • Fix the flanges with the

screws

BAMBU

BAMBU

INSTALLATION: part 2 at place

BAMBU

Put the base poles at the right position.

• Check the parallelism of the base poles using diagonal lines

• Drill and fix the base poles to the floor with screws (non included).

M12 recommended.

A = 3,282 m

C1 = C2 = 3,843 m

B = 2,0 m

BAMBU

Placing the poles in the base poles:

• Put the pole in the base pole.

Note: The poles at the base can be oriented in two positions, 0° and 15°, turning 180º the pole.

• Insert the bolt and fix it with the safety pin.

Note: Follow this procedure for the four poles.

BAMBU

Place the adjustment of the jointknot:

• Introduce it through the profile guide

• Block it to the right distance depending on the chosen assembly option.

BAMBU

Assembling the knot at the pole:

• Put the knot through the pole guide to the limit until the assembly flange.

BAMBU

Assembling the up profile at the poles.

• Bring up the up beams and fix the knot with the screws and the flanges previously placed.

BAMBU

Assembling the up profiles:

• Put the fixed strut at the mobile one (already placed at the up profiles) and introduce the guide profile until it leans on the pole

• Fix to the pole.

• Tighten the prisoners until the fabric is taut

BAMBU

BAMBU

Assembling the pole caps:

• Place the caps at the upper part of the poles.

BAMBU

Concrete slabs:

• It is possible to assemble the Bambu Canvas to the floor whenever is not permitted by law thanks to the use of 100 Kg. reinforced concrete slabs.

BAMBU

Connected structures: