Prepared by - WordPress.com...SONOMETER The Tint Testa is a photo optic instrument used to measure...
Transcript of Prepared by - WordPress.com...SONOMETER The Tint Testa is a photo optic instrument used to measure...
TITLE
Prepared by:
SONOMETER
The Tint Testa is a photo optic instrument used to measure
quickly, simply and accurately, visible light transmission (VLT)
through any type of glass or film. Comprising a light transmitter
and receiver, the Tint Testa is designed to determine the amount
of VLT that passes from the transmitter through tinted glass.
Many authorities and experts agree that less than 35% VLT on
car windows is dangerous.
The Tint Testa is used: In accordance with Government
regulation, for vehicle safety inspections, in traffic accident
investigation, by police in roadside inspections
The Tint Testa is operated by aligning the transmitter and
TINTED GLASS TESTER
The Tint Testa is operated by aligning the transmitter and
receiver on opposite sides of the glass and pressing the “Enter”
button. The results will appear on the display. All glass and tint
types can be tested on vehicles or buildings. The receiver can
measure visible light of any “colour” or frequency.
The Tint Testa provides a measurement of the amount of VLT
passing between thetransmitter and the receiver. This
measurment is expressed as a percentage. The test results can
be viewed on the unit’s display screen, or alternatively,
information can be transmitted by infra-red, to a serial printer.
Data can alsobe downloaded to a PC and then printed.
TINTED GLASS TESTER
TEORI UJIAN
R1 = Bacaan cahaya luar
R2 = Bacaan cahaya dalam
Peratusan cahaya = %1001
2×
R
R
R2 = Bacaan cahaya dalam
TINTED GLASS TESTER
MINOLTA T-10TINTED GLASS TESTER
PHOTODIODE LIGHT SOURCEILLUMINANCE METER
( MINOLTA T-10 )
TINTED GLASS TESTER
TOPCON IM5TINTED GLASS TESTER
GAS LEAK DETECTOR
RIKEN KEIKI ( GH -202F )GAS LEAK DETECTOR
PROBESENSOR
SWITCH ( OFF-LOW-HIGH )
SENSOR
INDICATOR LIGHT
GAS LEAK CHECKER MODEL JB-99
CASING
START
READYCHECK
PROBE SENSOR
SWITCH
START
WEIGHING
WEIGHING
PORTABLE BRAKE TESTERThe BrakeCheck is a fully self-contained, portable, battery-
powered device that can be used by workshops,
government traffic authorities, testing and inspection
stations etc. to test and report on vehicle brake efficiency.
The BrakeCheck can be used to test any type of vehicle,
including motorcycles, and can be positioned anywhere in
the vehicle. The unit determines braking efficiency of both
the Service Brake (Foot brake) and Hand Brake by
measuring deceleration. All operations are performed using
only three buttons on the unit.
The device operates on 4 rechargeable Nickel Cadmium
batteries and will power-down after a period of inactivity to
conserve energy. Results of the last test performed are
available for viewing and printing even after a power-down.
With the BrakeCheck, test results can be viewed on the
display or downloaded to a PC. Serial printing can be done
using the optional Infrared Link (or cable) printer.
It should be noted that the BrakeCheck may not comply
with your local Government Regulations concerning brake
testing of road registered vehicles. Local Statutory
requirements should be determined before a Brake Tester
is selected.
NSW Authorised Inspection Stations are referred to our
NSW compliant testers, Brake-Testa Millennium and Brake-
Testa Millennium HV for heavy vehicles.
What Type of Test can be done with
the Circuitlink Brake Tester?
� Service Brake
� Hand Brake� Hand Brake
Brake Efficiency
This is the average brake efficiency figure - an
expression of braking performance (%).
It is calculated from Test Speed and Stopping
Distance and can be compared with some statutory
requirements.
What are the advantages In using the
Circuitlink Brake Tester?
� Easy to Use.
� Easy to Calibrate.� Easy to Calibrate.
� Tamper Proof.
� Comprehensive and Simple Reports.
� Excellent Back -Up And Service.
� Very accurate.
� Low Cost.