Predetermined Time Systems
-
Upload
dinesh-garg -
Category
Documents
-
view
164 -
download
7
Transcript of Predetermined Time Systems
11
Chapter 26:Chapter 26: Predetermined Predetermined Time Systems (PTS) Using MTMTime Systems (PTS) Using MTM
MTM = Methods-Time MeasurementMTM = Methods-Time Measurement• MTM-1 // MTM-2 // MTM-3MTM-1 // MTM-2 // MTM-3
Developed by the Gilbreths:Developed by the Gilbreths: improved the bricklaying by 300%: a > 2000 yrs practice !!
Occurs in 2 steps:Occurs in 2 steps:• Break work down into its therblig elementsBreak work down into its therblig elements• Assign time values to each elementAssign time values to each element
Each element is independent and additiveEach element is independent and additive
22
MTM-1MTM-1
Most detailed Most detailed systemsystem
Motions are broken Motions are broken into 10 categoriesinto 10 categories
Times are found in Times are found in Tables 26.1-26.11Tables 26.1-26.11
Distance, Distance, complexity, and/or complexity, and/or weights are taken weights are taken into considerationinto consideration
MTM Categories MTM Categories • ReachReach• MoveMove• Turn Turn • Apply PressureApply Pressure• GraspGrasp• PositionPosition• ReleaseRelease• DisengageDisengage• Body MotionsBody Motions• Eye MotionsEye Motions
33
Methods Analysis and Time:Methods Analysis and Time:
Reference: Karger, D. & Bayha, F. “ Engineered Work Reference: Karger, D. & Bayha, F. “ Engineered Work Measurement”, 4th edition. New York, Ind. Press Measurement”, 4th edition. New York, Ind. Press 1987.1987.
• Time is given in time measurement units (Time is given in time measurement units (TMUTMU’s)’s)
1 TMU = 0.000 010 h = 0.000 600 min = 0.036 s1 TMU = 0.000 010 h = 0.000 600 min = 0.036 s
-Or--Or-
1 s = 27.78 TMU’s1 s = 27.78 TMU’s1 min = 1,667 TMU’s 1 min = 1,667 TMU’s 1 hr = 100,000 TMU’s1 hr = 100,000 TMU’s
No Allowances Included
44
MTM-2 and MTM-3MTM-2 and MTM-3
Fewer types of motions than MTM-1 Fewer types of motions than MTM-1 therefore are easier to usetherefore are easier to use
Fewer cycles needed in order to Fewer cycles needed in order to study the processstudy the process
• MTM-1 – requires 250 cycle timesMTM-1 – requires 250 cycle times• MTM-2 – requires 100 cycle timesMTM-2 – requires 100 cycle times• MTM-3 – requires 35 timesMTM-3 – requires 35 times
55
REACH: Table 26.1
Distances: Motion path of hand knuckle or finger tip. Body assistance (shoulder movement or pivoting) not included. Interpolation is suggested: R15A
Acceleration & Deceleration:Hands could be in motion at the beginning and end of the cycle. Then Acc. & Decel. can be omitted. Double this decrease is subtracted (Hand in Motion Table 26.2)
MOVE: Table 26.2
Hand is usually holding something (or pushing and dragging an object. Three cases are considered (nature of their destination).
66
Methods Analysis and Time:Methods Analysis and Time:
Movements can be refined to consider the effect of acceleration or Dec., or both. Also considered as a refinement for Object weight resistance to movement.
MTM: Both Moves and Reach are influenced by motions preceding or following them
Nomenclature:Accel. - Decel. If omitted we use m: mM6B or M6Bm
Weight: Included up to 2.5 lb/hand If two hand used, and object is 5lb, no extra time is allocated.
77
Methods Analysis and Time:Methods Analysis and Time:
Sliding: Takes the Object Weight (wood-wood = wood-metal = 0.4, metal-metal = 0.3)
Example: M6B = 8.9 a 5lb weight object(T-26.2) M6B5 = 8.9 1.06 + 2.2 = 11.8
Dynamic Factor Static Constant
Weight of Additional Components: To gain control through dynamic component for extra Travel Time.
88
Methods Analysis and Time:Methods Analysis and Time:
TURN: (Table 26.4)Considers the rotation of the hand, wrist and forearm about long axis of forearm:
Time = f(,weight, resistance to )
APPLY PRESSURE: (Table 26.5)Is the application of force without resultant move:APA = Basic element APB = APA + Regrasp
GraspPosition
DisengageRelease
Time Reducers
Skill Motions
99
Methods Analysis and Time:Methods Analysis and Time:GRASP: (Table 26.6)To gain Control of an object or Objects (followed by a move). Considers 5 Types:
Type 1: Pick-up Grasp: Follows an A or B reachType 2: Regrasp: Performed during a move: limited-outType 3: Transfer Grasp: Control from 1 hand to the otherType 4: Jumbled Grasp: Follows a C reachType 5: Contact, sliding or hook Grasp: Between a Reach & a Move
POSITION: (Table 26.7)
Collection of minor hand movements (less than 1 inch) for aligning, orienting, engaging 1 object with another.
1010
Methods Analysis and Time:Methods Analysis and Time:
Align: Orient longitudinal axes of the two items.
Orient: Rotation about long axis to align mating features (key in a lock, for example).
Engaging: Move along longitudinal axis to mate the parts
Disengage: Complement of the engage portion position Assumption: Alignement & Orientation are done: t = 0
Position Times: Table 26.7They are a function of: Pressure to Fit, Object Symmetry, Ease of Handling
1111
Methods Analysis and Time:Methods Analysis and Time:3 Classes of Fit: (Table 26.8)
1) Loose: Gravity will do it, code = 1
1) Close: Light pressure needed (1 APA), code = 2
1) Tight: Heavy pressure needed (3APA+G2), code=3
3 Classes of Symmetry: (Table 26.8)
1) Symmetrical (Code = S): No matter the orientation no rotation is needed for assembly (peg in round hole)
1) Non-Symmetrical (Code = NS): There is one and only one orientation in which the parts will mate.
1) Semisymmetrical: Any position that is not S or NS Example: A turn of 45°
1212
Same rules as MODAPTSSame rules as MODAPTS
Need experienced operator and Need experienced operator and experienced practitionerexperienced practitioner
Allowances are applied separatelyAllowances are applied separately Will need to measure certain number Will need to measure certain number
of cycles in order to get statistically of cycles in order to get statistically significant sample significant sample
1313
Plus Some Additional RulesPlus Some Additional Rules
Must be repetitive work, not occasionalMust be repetitive work, not occasional Distances (or degrees or other Distances (or degrees or other
qualifying codes) determine time qualifying codes) determine time elementselements
Tables must be present in order to get Tables must be present in order to get correct time per elementcorrect time per element
Additional weight (or symmetry or Additional weight (or symmetry or other “penalties”) may be appliedother “penalties”) may be applied