www.akcp.com042017

SPC+ features Power Monitoring so you can ensure you are not close to tripping your circuit breakers.Power switching used as part of our patent pending fire suppression system and UPS battery drain rate monitoring to shut down the cabinet in an emergency. Thermal map sensors wil check for cabinet hotspotsand enable you to adjust your data center to gain optimal PUE readings without exceeding environmentallimitations. Use SPC+ power meters to aid in PUE calculations.

Features

SPC+ upgrades any power strip. Simply connect power in to the SPC+ and power out to your existing strip. SPC+ adds power metering, switching, sensor ports and additional switched outlets, mounted 0U or 1U. For multiple cabinets use a single SPC+ Gateway with Remote devices, a cost effective upgrade path, monitoring all units from a single IP address.

Upgrade Your Existing Power StripPower.Sensors.Security Smart Power Controller (SPC+)

www.akcp.com042017

Basic Expansion BusLine power out to existing power strip Existing power strips,

or AKCP PS+(1 for each cabinet)

Cost Effective SolutionWith a traditional managed PDU, each device has it’s own controller and IP address. This increases the cost per unit, and the network managment overhead. By removing the meters and relays from the main power strip to a seperate 1U or 0U space, it allows for a greater number of outlets to be placed on the power strip. Our patent pending design allows the SPC+ Gateway to be removed. In case of failure or loss of communication the remote units will continue to operate independently.

SPC+

www.akcp.com042017

1U SPC+ Inline DeviceFeatures Diagram

12

3/54

AC Power In

AC Power Out

1. Sensor PortsMonitor your cabinets environmental condition.Check for hotspots with thermal map sensorsUse Smoke detector with our patent panding fire suppression system

5. Power MonitoringCheck how close you are to tripping your circuit breakers. Calculate data center PUE and identify energy savings Monitor UPS battery drain rates and alert when battery is critical

4. Additional Outlets2x C13 switched outlets add the ability to reboot devices remotely. For example, use AKCess Pro Server virtual sensors to ping a managed switch or router. If it fails to respond cycle the relay to reboot the device.

3. Power RelayThe power relay can shutdown the power strip. Use in conjunction with a smoke detector as part of our patent pending fire suppression system.

2. Basic Expansion BusCommunicate between remote and gateway devices. Monitor up to 8 cabinets from a single IP address

SPC+

www.akcp.com042017

0U SPC+ Inline Device

Sensor PortsMonitor your cabinets environmental condition.Check for hotspots with thermal map sensorsUse Smoke detector with our patent panding fire suppression system

Power MonitoringCheck how close you are to tripping your circuit breakers. Calculate data center PUE and identify energy savings Monitor UPS battery drain rates and alert when battery is critical

Additional Outlets4x C13 outlets switched on a x2 bank basis add the ability to reboot devices remotely. For example, use AKCess Pro Server virtual sensors to ping a managed switch or router. If it fails to respond cycle the relay to reboot the device.

Power RelayThe power relay can shutdown thepower strip. Use in conjunctionwith a smoke detector as partof our patent pending firesuppression system.

SPC+ is available in 0U configuration should you have no 1U spaceavailable. 0U devices come with a universal tool-less mountingsystem for easy installation in any cabinet.

Basic Expansion BusCommunicate between remote and gateway devices. Monitor up to 8 cabinets from a single IP address

SPC+

www.akcp.com042017

1U SPC+ Hotswap Gateway

Basic Expansion BusLine power out to existing power strip Existing power strips,

or AKCP PS+(1 for each cabinet)

SPC+ Hot-Swap Gateway (Optional)SPC+ can be installed with a 1U Gateway hotswap controller to take full advantage of our patent pending bootsequence technology. With this setup the main controller can be removed without any effect on your cabinets power. Should the controller need replacing it can be removed leaving remote SPC+ inline units undisturbed. Remote units will continue to function as normal due to our patent pending distributed boot sequence technology.Remote devices will continue to log total active power, boot sequences still function and your cabinets are protected by our patent pending fire suppression system.

SPC+

www.akcp.com042017

Rear

Top

Front

Side

1U, Inline, SPC+ Gateway for upgrading existing power strips

Technical DrawingsSPC+

www.akcp.com042017

RearSideFront

Tool-lessmounting

4x C13 outletsswitched x2

4x intelligentsensor ports

Basic Expansion Bus

Power metering

Power Relay

0U, Inline, SPC+ Gateway for upgrading existing power strips

Technical DrawingsSPC+

www.akcp.com042017

1U SPC+ Hot-swap Gateway

Technical Drawings

Power supply carriage

1U mounting bracketx8 Basic Expansion Bus (optional)

Front

Top

Rear

SPC+

www.akcp.com042017

SPC+ Specification

Status Indicators LED - Power on, network connectivity, sensor online and threshold status, output online and power output status

Sensors 4x Sensor Ports supports wide range of AKCP intelligent sensors.

Power In / Out 100V~250V, up to 32Amps C20 inlet with C19 - local power cable (16 Amp only) or,Fixed 1.5m cable with choice of connector (32A)

Mounting 1U 17” rackmount or 0U Universal Tool-less mount

Power Options Power Meter measures kWh, kW, RMS Current, RMS Voltage,Power Factor, Residual current with billable grade accuracy.Power/Fire Suppression Relay 2x block switched 2xC13 outlets

Communication Interfaces

10/100 Ethernet (Gateway only)2x Basic Expansion Bus Ports (Daisychain up to 8 units)

SPC+

About AKCPAKCP established in the USA in 1981, created the market for networked temperature, environmental and power monitoring solutions. Today with over 100 employees and130,000 installations, AKCP is the world’s oldest and largest manufacturer of SNMP enabled networked sensors for the data center.