Power System Dynamics -- Postgraduate Course of Tsinghua Univ. Graduate School at Shenzhen NI Yixin...

Power System Dynamics

-- Postgraduate Course of Tsinghua Univ. Graduate School at

Shenzhen

NI Yixin

Associate Professor

Dept. of EEE, HKU

<[email protected]>

Introduction

0.1 Requirements of modern power systems (P. S. )

0.2 Recent trends of P. S.

0.3 Complexity of modern P. S.

0.4 Definitions of different types of P. S. stability

0.5 Computer-aid P. S. stability analysis

0.6 Contents of our course

Introduction (1)0.1 Requirements of modern power systems (P. S. )

Satisfying load demands (as a power source) Good quality: voltage magnitude, symmetric three phase

voltages, low harmonics, standard frequency etc. (as a 3-phase ac voltage source)

Economic operation Secure and reliable operation with flexible controllability

Loss of any one element will not cause any operation limit violations (voltage, current, power, frequency, etc. ) and all demands are still satisfied.

For a set of specific large disturbances, the system will keep stable after disturbances.

Good energy management systems (EMS)

Introduction (2)0.2 Recent trends of P. S.

Systems interconnection: to obtain more benefits. It may lead to new stability issues ( e.g. low-frequency power oscillation on the tie lines; SSR caused by series-compensated lines etc. ).

Systems are often heavily loaded and very stressed. System stability under disturbances is of great concern.

New technology applications in power systems. (e.g. computer/ modern control theory/ optimization theory/ IT/ AI tech. etc. )

Power electronics applications: provides flexible controller in power systems. ( e. g. HVDC transmission systems, STATCOM, UPFC, TCSC, etc.)

Introduction (3)0.3 Complexity of modern P. S.

Large scale, Hierarchical and distributed structure, Non-storable electric energy, Fluctuate and random loads, Highly nonlinear dynamic behavior, Unforeseen emergencies, Fast transients which may lead to system collapse in

seconds or minutes, Complicated control and their coordination requests. -- Modern P. S. is much more complicated than ever and in

the meantime it plays a significant role in modern society.

Introduction (4)Some viewpoints of Dr. Kundur (author of the ref. book ):

--- The complexity of power systems is continually increasing because of the growth in interconnections and use of new technologies. At the same time, financial and regulatory constrains have forced utilities to operate the systems nearly at stability limits.

--- Of all the complex phenomena on power systems, power system stability is the most intricate to understand and challenging to analyze. Electric power systems of the 21 century will present an even more formidable challenge as they are forced to operate closer to their stability limit.

Introduction (5)0.4 Definitions of different types of P. S. stability

P. S. stability: the property of a P. S. that enable it to remain in a state of operating equilibrium under normal operating conditions and to return to an acceptable state of equilibrium after being disturbed.

Classification of stability Based on size of disturbance:

large disturbance stability ( transient stability, IEEE): nonlinear system models

small disturbance/signal stability ( steady-state stability, IEEE): linearized system models

The time span considered: transient stability: 0 to 10 seconds mid-term stability: 10 seconds to a few minutes long-term stability(dynamics): a few minutes to 1 hour

Introduction (6)0.4 Definitions of different types of P. S. stability (cont.)

Classification of stability (cont.) Based on physical nature of stability:

Synchronous operation (or angle) stability: insufficient synchronizing torque -- non-

oscillatory instability insufficient damping torque -- oscillatory

instability Voltage stability:

insufficient reactive power and voltage controllability

Subsynchronous oscillation (SSO) stability insufficient damping torque in SSO

Introduction (7)0.5 Computer-aid P. S. stability analysis

Introduction (8) 0.6 Contents of the course

IntroductionPart I: Power system element models

1. Synchronous machine models 2. Excitation system models 3. Prime mover and speed governor models

4. Load models 5. Transmission line and transformer models

Part II: Power system dynamics: theory and analysis 6. Transient stability and time simulation 7. Steady-state stability and eigenvalue analysis 8. Low-frequency oscillation and control 9. *Voltage stability

10. *Subsynchronous oscillation 11. Improvement of system stability Summary

Part I Power system element models

Chapter 1

Synchronous machine models

(a)

Chapter 1 Synchronous machine

(S. M.) models1.1 Ideal S. M. and its model in abc coordinates

1.1.1 Ideal S. M. definition Note: * S. M. is a rotating magnetic element with complex dynamic

behavior. It is the heart of P. S. It

* It provides active and reactive power to loads and has

strong power, frequency and voltage regulation/control

capability .

* To study S. M., mathematic models are developed for S. M.

* Special assumptions are made to simplify the modeling.


(S. M.) models1.1.1 Ideal S. M. definition (cont.): Assumptions for ideal S. M.

Machine magnetic permeability () is a constant with magnetic saturation neglected. Eddy current, hysteresis, and skin effects are neglected, so the machine is linear.

Symmetric rotor structure in direct (d) and quadratic (q) axes.

Symmetric stator winding structure: the three stator windings are 120 (electric) degrees apart in space with same structure.

The stator and rotor have smooth surface with tooth and slot effects neglected. All windings generate sinusoidal distributed magnetic field.


(S. M.) models1.1.2 Voltage equations in abc coordinates Positive direction setting:

dq and abc axes, speed direction Angle definition:

directions for abcfDQ windings i directions for abcfDQ u directions for abcfDQ

(uD=uQ=0)

: ( leading ahead )

120 , 240

240 , 120

a

b a a

c a a

d a


(S. M.) models

1.1.2 Voltage equations in abc coordinates (cont.) Voltage equations for abc windings:

where p= d / dt, t in sec.

rabc: stator winding resistance, in .

iabc : stator winding current, in A.

uabc: stator winding phase voltage, in V.

abc: stator winding flux linkage, in Wb.

Note: * pabc: generate emf in abc windings

* uabc~iabc: in generator conventional direction.

* iabc~abc: positive iabc generates negative abc respectively

a a a a

b b b b

c c c c

u pΨ r i

u pΨ r i

u pΨ r i


(S. M.) models1.1.2 Voltage equations in abc coordinates (cont.) Voltage equations for fDQ windings:rfDQ: rotor winding resistance, in .

f: field winding, D: damping winding in d-axis, Q: damping winding in q-axis.

ifDG, ufDG, fDG: rotor winding currents, voltages and flux linkages in A, V, Wb.

Note: * uD=uQ=0 * ufDQ~ifDQ: in load convention * ifDG ~fDG: positive ifDG generates

positive fDG respectively

* q-axis leads d-axis by 90 (electr.) deg.

0

0

f f f f

D D D D

Q Q Q Q

u pΨ r i

u pΨ r i

u pΨ r i


(S. M.) models1.1.2 Voltage equations in abc coordinates (cont.) Voltage equations in matrix format:

where ‘–’ before iabc is caused by generator convention of stator windings.

T

T

T

T

( , , , , , )

( , , , , , )

diag( , , , , , )

( , , , , , )

a b c f D Q

a b c f D Q

a a a f D Q

a b c f D Q

p

u u u u u u

Ψ Ψ Ψ Ψ Ψ Ψ

r r r r r r

i i i i i i

i

u Ψ ri

u

Ψ

r


(S. M.) models1.1.3 Flux linkage equations in abc coordinates

a aa ab ac af aD aQ a

b ba bb bc bf bD bQ b

c ca cb cc cf cD cQ c

f fa fb fc ff fD fQ f

D Da Db Dc Df DD DQ D

Q Qa Qb Qc Qf QD QQ Q

Ψ L L L L L L i

Ψ L L L L L L i

Ψ L L L L L L i

Ψ L L L L L L i

Ψ L L L L L L i

Ψ L L L L L L i

11 3 3 12 3 3

(6 1) (6 6) (6 1)

21 3 3 22 3 3

or = ;abc abc

fDQ fDQ

L L iL i

iL L


(S. M.) models1.1.3 Flux linkage equations in abc coordinates (cont.) In Flux linkage eqn.:

Lij ( i, j = a, b, c, f, D, Q ): self and mutual

inductances,

L11 : stator winding self and mutual inductance

, L22 : rotor winding self and mutual inductances,

L12 , L21 : mutual inductances among

stator and rotor windings ,

, i : same definition as voltage eqn..

Note: * Positive iabc generates negative abc

respectively. * The negative signs of iabc make Laa, Lbb, Lcc> 0.


(S. M.) models1.1.3 Flux linkage equations in abc coordinates (cont.) Stator winding self/mutual inductance (L11)

Stator winding self inductance (Laa, Lbb, Lcc)

Laa: reach max @ d-a aligning (when a=0, 180°)

reach min @ d-a perpendicular (when a=90, 270°)

Laa~ a: ‘sin’-curve, with period of 180°

(Ls>Lt>0, for round rotor: Lt=0) (See appendix 1 of the text book for derivation)

0 ( , , , , 0)aaa b c f D Q

a

ΨL i i i i i

i

cos 2 cos 2

cos 2 cos 2( 120 )

cos 2 cos 2( 120 )

aa S t a S t

bb S t b S t

cc S t c S t

L L L L L

L L L L L

L L L L L


(S. M.) models1.1.3 Flux linkage equations in abc coordinates (cont.) Stator winding self/mutual inductance (L11)

Stator winding mutual inductance

Lab: reach max |.| when a= -30, 150°

reach min |.| when a= 60, 240°

Laa~ a: ‘sin’-curve, with period of 180°

(Ms>Lt>0, for round rotor: Lt=0)(See appendix 1 of the text book for derivation)

, , , ,0 ( 0); 0 ( 0)a bab a c fDQ ba ab b c fDQ

b a

L i L L ii i

= cos 2( 30 )

( cos 2( 30 ))

= ( cos 2( 90 ))

= ( cos 2( 150 ))

ab ba s t a

s t

bc cb s t

ca ac s t

L L M L

M L

L L M L

L L M L


(S. M.) models1.1.3 Flux linkage equations in abc coordinates (cont.)

Rotor winding self/mutual inductance (L22)

Rotor winding self inductance (constant: why?)

Lff = Lf = const. >0

LDD = LD = const. >0

LQQ = LQ = const. >0

Rotor winding mutual inductance

LfQ = LfQ = 0, LDQ = LQD = 0

LfD = LDf = MR = const. > 0


(S. M.) models1.1.3 Flux linkage equations in abc coordinates (cont.) Stator and rotor winding mutual inductance (L12; L21 )

abc~f: (Mf=const.>0, period: 360°, max. when d-abc align)

abc~D: similar to abc~f, MfMD>0 abc~Q:(MQ=const.>0, period: 360°, max. when q-abc align)

cos cos

cos( 120 )

cos( 120 )

af fa f a f

bf fb f

cf fc f

L L M M

L L M

L L M

cos( 90 ) sin

sin( 120 )

sin( 120 )

aQ Qa Q a Q

bQ Qb Q

cQ Qc Q

L L M M

L L M

L L M


(S. M.) models1.1.3 Flux linkage equations in abc coordinates (summary) Time varying L-matrix : related to rotor position L11 (abc~abc): 180° period; L12, L21(abc~fDG): 360° period. Non-sparse L-matrix: most mutual inductances 0 L-matrix: non-user friendly, lead to abc dq0 coordinates!

0

0

0 0

a aa ab ac af aD aQ a

b ba bb bc bf bD bQ b

c ca cb cc cf cD cQ c

f fa fb fc f R f

D Da Db Dc R D D

Q Qa Qb Qc Q Q

Ψ L L L L L L i

Ψ L L L L L L i

Ψ L L L L L L i

Ψ L L L L M i

Ψ L L L M L i

Ψ L L L L i


(S. M.) models1.1.4 Generator power, torque and motion eqns.

Instantaneous output power eqn. (Pe in W)

Electromagnetic torque eqn. (Te in N-m, in rad.)

ccbbaae iuiuiuP

T

T

1 1[ ( ) ( ) ( )]

2 3

0 1 11

1 0 13

1 1 0

Pe P a b c b c a c a b

P abc abc

dLT p i i p i i i i i i

d

p i

(6 1)

: number of pole pairs,

: (- , )

P

T T Tabc fDQ

p

i i i


(S. M.) models1.1.4 Generator power, torque and motion eqns. (cont.) Rotor motion eqns.

According to Newton’s law, we have:

where Tm: input mechanical torque of generator (in N-m)

Te: output electromagnetic torque (in N-m)

m/m: rotor mechanical speed/angle (in rad/s, rad.)

e/e: rotor electrical speed/angle (in rad/s, rad.),

J: rotor moment of inertia (also called rotational inertia) J= Kg-m2

In the manufacturer’s handbook, J is given by [GD2], in ton-m2.

[GD2] (ton-m2) 103/4 J (Kg-m2).

d mm e

mm

J T Tdtd

dt

/ / ; / /m e P P m e P Pp p p p

2

iiimr


(S. M.) models1.1.4 Generator power, torque and motion eqns. (cont.) Rotor motion eqns. (cont.)

1 dd mm em e

P

mm

J T TJ T Tp dtdt

d ddt dt

( / / ; / / )m e P P m e P Pp p p p

1[ ( ) ( ) ( )]

3e P a b c b c a c a bT p i i i i i i


(S. M.) models1.1.5 Summary of S. M. model in abc coordinates and SI units:

6 volt. DEs. (abcfDQ): 6 flux linkage AEs. (abcfDQ): 2 rotor motion eqns. (,

Totally 14 eqns. with 8 DEs and 6 AEs. 8th order nonlinear model. 8 state variables are: (61) and , (related to 8 DEs)

Totally 19 variables: u: 4 (vD=vQ=0), i: 6, : 6, plus (Tm, , If 5 variables are known, remaining 14 variables can be solved. Usually uf and Tm are known (as input signals), 3 network interface

eqns. (3 vabc-iabc relations from network) are known.

1[ ( ) ( ) ( )]

3e P a b c b c a c a bT p i i i i i i

u p ri Li

1 d;m e

P

dJ T T

p dt dt


(S. M.) models

1.1.5 Summary of S. M. model in abc coordinates (cont.) Request of transformation of S. M. model:

abc to dq0 coordinates: Park’s transformation, Park’s eqns.

per unit system and S. M. pu model Reduced-order practical models:

-- Neglect stator abc winding transients (8th order 5th order). It can interface with network Y-matrix in Aes.

-- Introduce practical variables (E’dq, E”dq, Ef etc.)

Power System Dynamics -- Postgraduate Course of Tsinghua Univ. Graduate School at Shenzhen NI Yixin...

Documents

Transcript of Power System Dynamics -- Postgraduate Course of Tsinghua Univ. Graduate School at Shenzhen NI Yixin...